eran01s Duke Today: HC - Typical L2 Configuration Commands
8) non ge
H3C - Typical L2 Configuration Commands
Pott et eet
1.4. VLAN Configuration
4 Configure VLANs
#add acess ports o VLAN
°
port erhl/0/1 to exnl/o/24
or VolP phones
interface Kthernet/0/1
port trunk pyid vlan 10
lindo port trunk permit vlan
Display conigued VLANs
1.2.Bridge Aggregation
Orders importantin LAG group configuration
‘Clear out current port conte
(Create LAG group and set to dynamic HLACP is desiree
‘Add the ports to the LAG
1p remaining config onthe LAG.
tpn srackarellcom/2011/10lcongurationcemmands-1 hleria018 Duke Today: HSC - Typical L2 Configuration Commands
fegation verbose
Alinerfaces should have a status of S (selected). they say U (unselected),
someting is wrong,
41.3. Trunk Ports (802.10 tag)
Configure interfaces as tunk ports between switches according to reference
topology.
Repeat the above configuration on relevant pots.
Use the below command to verfy the unk configuration
41.4. Spanning Tree - MSTP interoperability with PVST*
Ityou want PVST to interoperate wih MSTP, you need tothe Cisco to
interoperate wth an eee 802.1 standard BPDU packet and not the proprietary
PVST packet. The only way to have the Cisco running PVST* to send standare
802.1 packets i to ensure thatthe native van is equalto 1
‘The other possibly sto do nothing and have each pass-through the'r bpd
packets which are unknown inthe other environment. To make your He easier,
have only one connection between both environments
‘Tne spanning tre configuration on each swich using the CST ofthe MST.
to interoperate wth Cisco PVST+ vlan ieee RSTP SPOUS.
‘Apply these commands to all HP switches
Configure the access ports or sip ecge mode:
age Port:
[AIHSC swiches should agree thatthe root bridge isthe Cisco root bridge for
the csr
Aso, standardize the STP port costs in both platforms.
On the HP-A switches:
lise] stp patncost:
on Cisco:
‘Very wit he folowing commands:
yernet 1/0/1
‘ter connecting PC, the access port should move to forwarding state
immediatly
tpn srackarellcom/2011/10lcongurationcemmands-1 hleria018 Duke Today: HSC - Typical L2 Configuration Commands
a
418. Voice VLAN
Configure pots to support Cisco VolP phones. Interfaces willeary voice and
data VLANs. Place phones in voice VLAN via LLOP COP compliance. Place in
appropiate IDF-VoIP-VLAN id per ste configuration. To avoid stp issues,
remove vin fom the interface and set as an edge pot.
Interface commands’
Configure addtional ports as necessary.
Connect P Phone ta interface configured in Voice VLAN,
Data VLAN tat wl pass Vac untagged while voice trafic willbe tagged.
Interfaces in the voice vin wll rst the QOS (602. 1p or DSCP) markings on
voice packets glven preferetal wealmenvcissifed based on packelirame
markings.
1.6. Layer 3 VLAN Interface Configuration
Assign IP addresses tothe Management VLAN interfaces:
To show the confgured interface address
Neighboring interfaces should be reachable
17.Interface Options and Port Security
1.74.dombo Frames
turbos are on y dete, ut o manually eral sch o pass jumbo ares ona gen
terface git/0/
1.2.0H6P Snooping
Enable DHGP Snooping on the switch and display resus of elent ONCP request,
\Wth OHCP-Snooping enabled, a swich wilbock al OHCP ACKs preventing rogue
DHGP servers om affecting the netwotk. n order fora trusted DHCP server to
‘uncton correctly and respond to requests, the interface must be configured as
“ust
tpn srackarelicom/2011/10lcongurationcemmands-1 hleria018 Duke Today: H3C - Typical L2 Configuration Commands
8 Specty Gigabitétnemel 1/01 as tustes
‘Switen should maintain DHOP snooping database tru snooping OHCP requests,
‘and responses. Use the fllowing to veri
dlaplay dnep-sncoping po!
# enable sFlow on each interface required:
nt ten 2/2/0/1
sflow enable ( inbound | outbound
rave (detaclt is 1638)
Verity collector receives fow data.
1.8, Por mieing
cal Port miroring
tpn srackarelicom/2011/10lcongurationcemmands-1 hl
78eria018 Duke Today: H3C - Typical L2 Configuration Commands
interface ochi/a/7é
stp disable
mirroring-group 1 mirroring-port ethi/0/1 to ethi/0/9 be
irroring-group 1 monicor-port ethi/0/24
splay miroring configuration
display mizroring-group 1
Connect host o mioring port and generate traf.
Connect Ethereal host to monitor port and observe packet capture.
Etyerealappication should capture packet data from source mirorng port
$4 cenit en Gone
5 comments:
eat
Ren
smonanimed sa 5182014552 08
‘canu peas hlp ets cntgure PSECin 360M ue?
FE) ora reten ontrnte steht
a
Te orccnre stn voy oso campeon re ae
a
Comments: Goole Accan +
=a) ae
tpn srackarelicom/2011/10lcongurationcemmands-1 hl 28eria018 Duke Tosiay: HC
Sunrobate Pst commen)
1 ceo bees
1 Tre Guten Project
Yow my comps pote
tpn srackarelicom/2011/10lcongurationcemmands-1 hl
= Typical L2 Coniguration Commands
‘Sle ns, Ponered yon,