Sunteți pe pagina 1din 3

F10 - Retrofit DEC switch for Normal/Sport/Sport+ modes

Credit to miotoo on bimmer forum.

I really wanted to enable the sports control in my non-sport 520d F10 (4.2011).

Parts needed:

1x 61319202936 DEC switch with Normal/Sport label


2x 61130005197 Wire with bushing contact DEC switch side
2x 61131383776 bushing contact ICM side

The install is quiet easy, albeit one step which was a bit*h to do (see 8 below)

Dis-assembly steps:
1. Pry out rear seat ventilation cover, pull top 1st.
2. Pry out phone compartment lock cover.
3. Remove the revealed torx screw.
4. Pry out the middle console, starting from the rear and lift towards the front.
5. At this point you can decide to disconnect all connectors for easier installation/replacement of
your DEC switch. If you do, the idrive controller connector is a clip-in, press the tab on the side to
release. The 2 DEC switch connectors have a notch that fits into a tiny hole on the connector
socket surface. I used a mini screwdriver to 'lift' the side of the socket and the connectors came
out easily.
6. Remove the 2 torx screws that hold the current control module and remove it.
7. Remove the revealed screw that holds the phone compartment on its front side and lift the
compartment towards the front. The ICM module to which you need to connect the 2 wires, lays
below.
8. This last step of dis-assembly was accessing & releasing the ICM connector. The initial problem
is that even when you release the connector lever, there are 2 plastic extensions/flanges from the
side & in front of the connector that block it's complete removal. So after fiddling around in
acrobatic finger movements in there without success - I can tell you that the easiest way to
release it is to open the 2 central console rear screws which were revealed when you removed
the rear seat ventilation cover in step 1. Once these screws are removed, it's possible to lift the
rear of the console about half an inch which will be just enough to release the ICM connector as
the blocking flanges are now higher...if you work alone, use a small piece of wood under it to
hold it in place for assembly.

Connection:
Now that we have everything exposed and easily accessible, need to do the following.
1. Prepare the wires. The supplied 61130005197 wire with contact is long enough for the
connections. Use a crimping tool to connect a 61131383776 contact to the bare end of the two
wires.
2. On the ICM connector side, remove the connector cover. The connector is made of 2 parts that
slide into each-other. a double & a single row. Identify the empty slots for pins 31 & 45 and slide
your new wires in. Make sure they are fully inserted.
3. Channel the wires inside the center console towards the front and through to the same place
where the DEC switch connectors appear.
4. Slide the new wires to the DEC switch connector slots 4 & 5, making sure ICM 31 goes to DEC 5,
and ICM 45 to DEC 4 (see attached ISTA wiring diagram).

Assembly is a reverse of dis-assembly. The center console clips are very rigid and require quite a
force to 'click' back in.

Next step is to activate the switch via coding (using BMW ENET Cable and E-sys software).

Based on the various forum posts & my own experience, I suggest a full VO CODE of the car. after
removing 205 & adding 2TB to the options list. This took care of adding the SPORT settings menu
to the CIC, added the Kombi graphics and made the proper settings for ICM & EGS now shows
S1-S7 when shifted left. Note if you do that, other personal coding will need to be recoded. Some
I have include activation of BMW Online menu, the digital speed display, memory off for the A/C
etc.

Edit: After VO coding of the modules, need to FDL code the SZL Lenkrad_Schaltpaddles -> nicht
aktiv. Otherwise a fault error for the missing shift paddles will be registered in the module fault
memory.

Result:
1. What can I say. I'm very happy now. I love that finally I can have a more accurate steering at
highway speeds and I can't believe how better is the throttle response. In a way I find it a shame
that people buy the 'hardware', and such minor 'software' settings can transform what is
essentially THE function of the device they bought...

2. I'm yet to understand what exactly is the programming difference between this mod and an
original 2TB purchase. Is there a way to actually identify this difference?

3. I have no ECO PRO functionality and while I tried to add 4U2 to the VO, It seems my KOMBI
does not have the firmware to handle it, and I have a discrepancy in display wording. CIC shows
COMFORT/SPORT/SPORT+ while KOMBI shows NORMAL/SPORT/SPORT+. The animation is also
missing and coding the car with a later ZeitKriterium left me with the heater showing the residual
heat logo all the time. So I dropped it for now and maybe if I figure out how to upgrade the
I-Level, it will be an option..

Afterthought / additional suggestions:

1. The 1st dealer I went to only had the 2 wires, and didn't have in stock the extra pins. He sent
me to a 2nd dealer that showed stock on the system. When I went there, the guy laughed and
asked how many I wanted. He gave me a bunch for free and told me that while it's not clearly
identified in realoem or told by the dealer, in fact the contact pins on both sides of the wires (the
DEC & ICM connectors) are identical and widely used in many connectors and cars. They
themselves don't use the outrageously expensive items from BMW...
2. Further info showed you can use alternative wires, ready with the same pins crimped, from an
Audi dealer - item # 000 979 009 - Easy...
3. The DEC switch is phasing out to a 'modular' model....

S-ar putea să vă placă și