Documente Academic
Documente Profesional
Documente Cultură
CONTENTS
1
1 RBS6000 Hardware and Software
GSM900 TEI DCP1 DCP2 DCP3 MCTRI Max PWR Max TRX TX MPWR
GSM900 TEI DCP1 DCP2 DCP3 MCTRI Max PWR Max TRX TX MPWR
2
GSM900&GSM1800 3X3 (RUS 80W)
GSM900 TEI DCP1 DCP2 DCP3 MCTRI Max PWR Max TRX TX MPWR
3 / / / / / / /
7 / / / / / / /
11 / / / / / / /
2G RBS6000 RUG
Configuration.xls
GSM1800 TEI DCP1 DCP2 DCP3 MCTRI Max PWR Max TRX TX MPWR
GSM1800 TEI DCP1 DCP2 DCP3 MCTRI Max PWR Max TRX TX MPWR
3
GSM1800 3X3 (RUG)
GSM1800 TEI DCP1 DCP2 DCP3 MCTRI Max PWR Max TRX TX MPWR
2G RBS6000 RUS
Configuration.xls
3 2G RBS6000 Swap
3.1 Flow chart for 2G rbs6000 swap
2GMP
RAN TN
BTS SUPPORT CORERAN
(BSC)
NOC CENTER
1. 2GMP sends the 2G rbs6000 swap plan job in each last weekend.
2. We (BSC) will prepare the 2G rbs6000 swap scripts with the plan job.
3. If the plan job has new site or addition E1 site, TN_CORERAN will provide the E1 DSX
port.
4. We will send the jumper to CENTER prepare the connections.
5. Start for 2G rbs6000 site swap. BTS call NOC&BSC. NOC will be record. BSC will be
start halt site and input the script.
6. Wait the BTS completed the sites hardware and IDB. We will check the transmission
with BTS. If the transmission is WO that we will bring the MOs into service and unblocking the
4
MOs. If the transmission is ABL that BTS will be check the transmission cable.
7. Wait the BTS completed the antenna jumper. We will active the site and BTS will test call
on site.
8. Wait the BTS response the test call was completed. At this moment, 2G rbs6000 swap
was completed too.
5
3. Open the Command Handling. Choose the Start->Applications->Ericsson->Tools->AXE
Management-> Command Handling.
6
4. Copy and paste the Script in the Command Handling. Copy the script ->Right click the
input area for the command handling->Choose the Edit->Paste.
7
2. Change the cell status for halted.
COMMAND: RLSTC:CELL=A2006A,STATE=HALTED;
3. Check the status information for the managed objects (MO). The status as below
when the site will be halted.
COMMAND: RXMSP:MO=RXOTG- 432,SUBORD;
8
4. Check all of administration data for the MO instances. When parameter
SUBORD is used, MO instances are processed only if their superior MOs are
defined. The TG parameter as below before the RBS6000 swap.
COMMAND: RXMOP:MO=RXOTG-432;
9
5. Check the DIP status. There are 3 statuses of WO (Working) or MBL
(Manually blocked) or ABL (Automatically blocked) with the DIP.
COMMAND: DTSTP:DIP=152RBL2;
6. Deblock the specified DIP, when the DIP status was MBL:
COMMAND:DTBLE:DIP=152RBL2;
7. Check the device state details. The start DEV = DIP*32 and the end
10
DEV = start DEV + 31.
COMMAND: STDEP:DEV=RBLT2-46864&&-4895;
11
After deblocked the devices status as below:
12
11. Manual forced blocking indication the subordinate MOs.
COMMAND: RXBLI:MO=RXOTG-432,SUBORD,FORCE;
13
12. Out of service for the subordinate MOs. The MOs must be manually blocked,
that is in state COM.
COMMAND: RXESE:MO=RXOTG-432,SUBORD;
13. Change the CF terminal endpoint identifier. When the MOs out of service can
be use the RXMOC change all of the MOs configurations. In general practice,
14
GSM900 = 1st TG &
GSM1800 = 2nd TG in the cascade stream. TEI value of CFs = 62, 61, 60and so
on.
COMMAND: RXMOC:MO=RXOCF-432,TEI=62;
14. Deletes specified Abis paths between the Base Station Controller (BSC) and
the BTS for a specified TG in the transmission mode TDM. The last Abis path within a
TG will only be deleted if its associated transmission device does not have a
connected Digital Path (DIP).
COMMAND: RXAPE:MO=RXOTG-432,DCP=ALL;
15. Defines one or more Abis paths between the Base Station Controller (BSC)
and the BTS. This command is only valid if TG is in the transmission mode Time
Division Multiplexing (TDM).
COMMAND: RXAPI:MO=RXOTG-432,DCP=1&&15,DEV=RBLT2-4865&&-4879;
15
To facilitate the deployment of CS-3/4 & EDGE, for 2xE1 and 2xDUG case (dual band or large
configuration), please connect both E1s to the 1st DUG and then cascade them to the 2nd
DUG. For this configuration, we can dynamically assign TSs of these 2xE1 between the two
DUGs.
16. Define the TRX tei value and dcp mapping in the BSC.
COMMAND: RXMOI:MO=RXOTRX-432-0,TEI=0,DCP1=128,DCP2=129&130;
16
COMMAND: RXMOI:MO=RXORX-432-0,RXD=AB,BAND=GSM1800; (PCS)
COMMAND: RXMOI:MO=RXOTS-4321-0-0&&-7;
COMMAND: RXMOC:MO=RXOTX-432-0,CELL= A2006A;
The GSM900 TRX parameter as below:
The GSM1800 TRX dont mapping MCTR for RBS6000 RUG. Its TRX parameter as
below:
18. Adding the MCTR for the GSM. PCS dont mapping the MCTR for RBS6000
RUG.
COMMAND: RXMOI:MO=RXOMCTR-432-0,MAXPWR=48,MAXTRX=3; (RUS 60W)
COMMAND: RXMOI:MO=RXOMCTR-432-0,MAXPWR=49,MAXTRX=4; (RUS 80W)
COMMAND: RXMOC:MO=RXOTRX-432-0,MCTRI=0;
17
COMMAND: RXMOC:MO=RXOTRX-432-1,MCTRI=0;
COMMAND: RXMOC:MO=RXOTRX-432-2,MCTRI=0;
21. Brings MOs into service and manual unblocking the MOs.
COMMAND: RXESI:MO=RXOTG-432,SUBORD;
18
COMMAND: RXBLE:MO=RXOTG-432,SUBORD;
19
22. Check the MOs status. When all of the MOs states are operation, the cell can
be active.
COMMAND: RXMSP:MO=RXOTG-432,SUBORD;
20
Above fault code is CF-2A69 (Cabinet Product Data Mismatch). Action: Add the values stated
on the cabinet enclosure label to the IDB description by BTS team. Can be checking the alex
fault list for RBS6000. It path as below: http://alex/cgi-bin/alex
21
26. Change the limit value for availability with traffic channel.
COMMAND: RLSLC:CELL=A2006A,CHTYPE=SDCCH,LVA=15;
COMMAND: RLSLC:CELL=A2006A,CHTYPE=TCH,LVA=21;
22
they are only one TG number.
The scripts & MO data of 2G RBS6601 swap as below:
Config: 4G+2P
B14_W1773A&W34 B14_W1773A&W34
04A_RBS6601_Script.txt 04A_RBS6601_MO.txt
B15_Y1829B&Y382 B15_Y1829B&Y382
9B_RBS6301_Script.TXT9B_RBS6301_MO.txt
23
Open the attachment files with CR, can be look at the parameter for the site.
24
3. Set up new site in the plan area (b16_z2406b).
Edit->New->Site
Input the specific parameters into the corresponding blank area, and then click new.
25
4. Set up new cell in the plan area b16_z2406b.
Edit->New->Cell->Internal
26
5. Set up inner cell
Input CO and RO, then click OK.
27
7. Fine a cell template in the same BSC, and then copy all the parameters to the new
cell.
Selected the cell template. Edit->Copy->All Parameters.
Select the defined new cell. Edit->paste. then change the parameters as the follow
pictures showed.
28
29
30
If all parameters are input the new cell plan area, then click OK.
31
8. Define Neighbor cells of the new cell.
Input Neighbor cell name, choose CS type, if the neighbor cell is internal cell with new cell,
please choose the CS to YES, else choose NO, and then click New. Keep doing this step
until all neighbor cells defined.
32
Change the parameters of all neighbor cell, then Edit->Apply.
33
Check internal cell properties.
34
Check inner cell properties.
35
Input update job name, update of BA list choose Unconditional, Fallback area
choose YES, and then click OK.
36
13. Check the state of the update job. File->Jobs->My own.
37
Check the update job report
NOTICE: If the CNA update job is failed, look into the ALEX (http://alex/cgi-bin/alex)
for help.
14. Check if all the cell parameters are correctly defined. Open a command handling
and input corresponding commands.
38
4.2 Command Handling With New Site.
1. Check the new cell parameters in the BSC with command handling.
RLDEP:CELL=XXX;
Command description: prints cell description data
RLCFP:CELL=XXX;
Command description: prints cell configuration frequency data.
39
RLDHP:CELL=XXX;
Command description: prints dynamic hr allocation data.
RLPRP:CELL=XXX;
Command description: prints BSC differential channel allocation priority profile resource
type data.
RLGSP:CELL=XXX;
Command description:prints GPRS data.
RLNRP:CELL=XXX,CELLR=ALL;
Command description: prints all the neighbour cells and relation data.
40
RLMFP:CELL=XXX;
Command description: prints all the measurement frequencies of specific cell.
RLCPP:CELL=XXX;
Command description: prints cell configuration power data.
RLLHP:CELL=XXX;
Command description: prints cell locating hierarchical data.
41
2. Define a New TG For the New Site
RXMOI:MO=RXOTG-
58,SWVER=B1305R061E,TRACO=POOL,RSITE=LOC_2402,COMB=HYB;
Command description: De f ine tg -5 8 fo r th e site 24 02 , B TS so f t wa re ve rsio n is
B1 30 5 R06 1 E . Tran scod e r con ne ct io n t ype is P OO L , ra d io sit e na me is
LO C_ 24 02 , an d co mb ine r is HY B (Hyb rid ) co mb ine r.
RXMOI: MO=RXOIS-58;
Command description: Defines IS MO in tg-58. The IS is short for interface switch.
B16_Z2402AB&Z30
18A_New site script.TXT
42
5 Abis Over IP Site Cutover
Abis over IP site cutover is change the transmission of between the BSC and the BTS from
TDM transport networks to IP or ethernet transport service
In the preparation phasesend the TG PSTU name for the Abis over IP site to TN team
43
CommandRXTCE:MO=RXOTG-213,CHGR=0,CELL=Z2516A;
2Define the SCGR, Super Channel Group: SCGR=[TG number], the SCGR no.
follow the TG NO. Corresponding parameters are common to all various TGs &
SCGRs.
Command:RRSGI:SCGR=101,MODE=IPM,PSTU=TG101,MBWDL=8192,MBWUL=
8192,JBSUL=20;
44
3. Define TF and ISthe same as E1 site
CommandRXMOI:MO=RXOTF-101,TFMODE=SA;
CommandRXMOI:MO=RXOIS-101;
5. Define TRXs DCP with CS3CS4 / EGPRS settingsThese are one SC NO. for the
TRX must be 0 on each TG with AbisoIP.
!Assign each TRXs with ascending SC no. for the TRXs,!
! TEI Value: SC number: !
! 0/4/8 0 !
! 1/5/9 1 !
! 2 / 6 / 10 2 !
! 3 / 7 / 11 3 !
Command RXMOI:MO=RXOTRX-101-0,TEI=0,DCP1=178,DCP2=179&&186,SC=0;
Command RXMOI:MO=RXOTRX-101-1,TEI=1,DCP1=187,DCP2=188&&195,SC=1;
Command RXMOI:MO=RXOTRX-101-2,TEI=2,DCP1=196,DCP2=197&&204,SC=2;
Command RXMOI:MO=RXOTRX-101-3,TEI=3,DCP1=205,DCP2=206&&213,SC=3;
45
Command RXTCI:MO=RXOTG-101,CELL=[Cell Name],CHGR=0;
5.4 Check the SIU status and activate the BTS again.
1. Prints the data for PSTU.
Command RRPTP:PSTU=TG101;
The PSTU is not ready:
46
5. Orders the manual unblocking of the Moinstance.
Command RXBLE:MO=RXOTG-101,SUBORD;
CESoPSN Encapsulation for emulation of low-rate TDM circuits over PSN. In the
bsc, CESoPSN site cutover main task is change CRCCyclic redundancy checkof
the transmission from 0 to 2. 0is no CRC, only Frame Alignment Signal word
violations are counted as bitfaults. 2 is CRC-4 ,performed on both outgoing and
incoming PCM bitstream, and E-bits will be sent to the remote end. The remote end
must have the same type of supervision.
In the preparation phasesend the RBLT for CES site to TN team.
The following format:
GSM PCS GSM TG PCS TG
3G
BSC Site Site Abis/CES RBLT DSX PSTU PSTU
No.
No. No. name name
47
3. Prints all administration data for one or more MO instances.
CommandRXMOP:MO=RXOTG-230,SUBORD;
4. Prints all defined Abis paths for specified TG in the BTS. Write down the DEV and DCP.
CommandRXAPP:MO=RXOTG-230;
7. Initiates a printout of all initial data for the specified digital path.
CommandDTIDP:DIP=137RBL2;
CESoPSN site cutover main task is change CRC (Cyclic redundancy check) of the
transmission from 0 to 2.
48
3. Removes specified MOs from service.
CommandRXESE:MO=RXOTG-230,SUBORD;
4. Deletes specified Abis paths between the BSC and the BTS in the transmission.
CommandRXAPE:MO=RXOTG-230,DCP=ALL;
8. Initiates a printout of all initial data for the specified digital path.
CommandDTBLE:DIP=137RBL2;
2. Initiates a printout of the state for the specified DIP WOthe transmission is
OK. ABL, the transmission is Disconnect.
CommandDTSTP:DIP=137RBL2;
Procedure Printouts
3. Defines one or more Abis paths between the BSC and the BTSThe DEV and
DCP are the same as before cutover.
49
CommandRXAPI:MO=RXOTG-230,DCP=1&&6,DEV=RBLT2-4385&&-4390;
4. Prints all defined Abis paths for specified TG in the BTS again.
CommandRXAPP:MO=RXOTG-230;
7 CS3CS4 Configuration
0 178 179&&186
1 187 188&&195
2 196 197&&204
3 205 206&&213
4 214 215&&222
5 223 224&&231
6 232 233&&240
7 241 242&&249
8 250 251&&258
50
TRX TEI DCP1 DCP2
9 259 260&&267
10 268 269&&276
11 277 278&&285
Command:
RXMOI:MO=RXOTRX-XXX-0,DCP1=178,DCP2=179&&186;
RXMOI:MO=RXOTRX- XXX-1,DCP1=187,DCP2=188&&195;
RXMOI:MO=RXOTRX- XXX-2,DCP1=196,DCP2=197&&204;
RXMOI:MO=RXOTRX- XXX-3,DCP1=205,DCP2=206&&213;
RXMOI:MO=RXOTRX- XXX-4,DCP1=214,DCP2=215&&222;
RXMOI:MO=RXOTRX- XXX-5,DCP1=223,DCP2=224&&231;
RXMOI:MO=RXOTRX- XXX-6,DCP1=232,DCP2=233&&240;
RXMOI:MO=RXOTRX- XXX-7,DCP1=241,DCP2=242&&249;
RXMOI:MO=RXOTRX- XXX-8,DCP1=250,DCP2=251&&258;
RXMOI:MO=RXOTRX- XXX-9,DCP1=259,DCP2=260&&267;
RXMOI:MO=RXOTRX- XXX-10,DCP1=268,DCP2=269&&276;
RXMOI:MO=RXOTRX- XXX-11,DCP1=277,DCP2=278&&285;
TRX Timeslot
Control Channel 0 0 1 2 3 4 5 6 7
E1 Devices 0 1 2 3 16 31 Total 32
NUMREQCS3CS4BPC = 0
51
CS3CS4 TRX AND E1 DEVICES RELATION
TRX Timeslot
Control Channel 0 0 1 2 3 4 5 6 7
RES64K
E1 Devices 0 1 2 3 4 5 6 16 31 Total 32
NUMREQCS3CS4BPC = 4
Command:
RXAPI:MO=RXOTG-XXX,DCP=1&&6,DEV=RBLT-1&&-4,RES64K;
RXAPI:MO=RXOTG-XXX,DCP=1&&6,DEV=RBLT-5&&-6;
RLGSC:CELL=XXXX, CHCSDL=CS4;
RLBDC:CELL=XXXX, NUMREQCS3CS4BPC=4;
TRX Timeslot
Control Channel 0 0 1 2 3 4 5 6 7
RES64K
E1 Devices 0 1 2 3 4 5 6 7 8 9 16 31 Total 32
NUMREQCS3CS4BPC = 8
Command:
RXAPI:MO=RXOTG-XXX,DCP=1&&6,DEV=RBLT-1&&-8,RES64K;
RXAPI:MO=RXOTG-XXX,DCP=1&&6,DEV=RBLT-9&&-12;
RLGSC:CELL=XXXX, CHCSDL=CS4;
RLBDC:CELL=XXXX, NUMREQCS3CS4BPC=8;
RBS6000 CS3CS4
Script.txt
52
RLDSI:CELL=V2263C;
RLDGI:CELL=V2263C,SCTYPE=OL,CHGR=1,BAND=GSM1800;
2. Check the cell configuration frequency data, then add the PCS frequency
and hopping sequence number to the expansion channel group. Relocate
PCS SDCCH to GSM, if GSM had 2 CHGR, then relocate SDCCH to CHGR
with GSM BCCH.
RLCFP:CELL=V2263C&V5589C;
RLCFI:CELL=V2263C,CHGR=1,DCHNO=523&662;
RLCHC:CELL=V2263C,CHGR=1,HOP=ON,HSN=34,MAIO=DEFAULT;
RLCCC:CELL=V2263C,CHGR=0,SDCCH=2;
53
4. Defined the cell locating overlaid subcell data for designated value.
RLOLC:CELL=V2263C,LOL=130,LOLHYST=2,TAOL=61,TAOLHYST=0,DTCBHYST=0,NDIS
T=0,NNCELLS=1;
5. Turn the subcell load distribution status on, and then change the subcell
load distribution data for designated value.
RLLLC:CELL=V2263C,SCLD=ON,SCLDSC=OL,SCLDLOL=20,SCLDLUL=30;
6. Change the cell locating intracell handover data of overlaid subcell for
designated value.
RLIHC:CELL=V2263C,SCTYPE=OL,IHO=ON,MAXIHO=3,TMAXIHO=6,TIHO=5;
54
7. Change the cell locating data for designated value.
RLLOC:CELL=V2263C,FBOFFSP=7;
RLLOC:CELL=V2263C,SCTYPE=UL,BSTXPWR=50;
RLLOC:CELL=V2263C,SCTYPE=OL,BSTXPWR=39;
55
8. Change the cell locating hierarchical data for designated value.
RLLHC:CELL=V2263C,LAYER=2,LAYERTHR=75;
9. The AMR power control cell data of overlaid subcell match underlaid
subcell.
RLAPC:CELL=V2263C,SCTYPE=OL,ssdesdlafr=85,qdesdlafr=30,qdesulafr=35;
RLAPC:CELL=V2263C,SCTYPE=OL,ssdesdlahr=85,qdesdlahr=30,qdesulahr=35;
10. The dynamic ms power control cell data of overlaid subcell match
underlaid subcell.
RLPCC:CELL=V2263C,SCTYPE=OL,qdesul=35;
56
11. The dynamic BTS power control cell data of overlaid subcell match
underlaid subcell.
RLBCC:CELL=V2263C,SCTYPE=OL,ssdesdl=85;
12. Change the underlaid subcell support cell general packet radio service.
RLGSC:CELL=V2263C,scalloc=UL;
13. Change the connection of cell to channel allocation profile data for
designated value.
RLHPC:CELL=V2263C,chap=6;
57
8.2 MO data description for GSM
1. Change the GSM frequency hopping for baseband hopping.
RXMOC:MO=RXOTG-60,FHOP=BB;
2. Change the GSM TF synchronization mode for master, and the TG cluster
identity for designated value.
RXMOC:MO=RXOTF-60,TFMODE=M;
RXMOC:MO=RXOTG-60,CLUSTERID=3;
58
8.3 MO data description for PCS
1. End the GPRS for PCS and support the GPRS for GSM.
RLGSE:CELL=V5589C;
RLGSI:CELL=V2263C;
4. Disconnect the before PCS cell for the CHGR 0 with tg-14 and connect
after PCS cell for the CHGR 1 with tg-14.
RXTCE:MO=RXOTG-14,CELL=V5589C,CHGR=0;
RXTCI:MO=RXOTG-14,CELL=V2263C,CHGR=1;
59
RXMOC:MO=RXOTRX-14-0,CELL=V2263C,CHGR=1;
7. Change the channel alarm limit value for availability to specified value.
RLSLC:CELL=V2263C,SCTYPE=UL,CHTYPE=SDCCH,ACL=A1,LAV=15;
RLSLC:CELL=V2263C,SCTYPE=UL,CHTYPE=TCH,ACL=A1,LAV=21;
RLSLC:CELL=V2263C,SCTYPE=UL,CHTYPE=BCCH,ACL=A1;
RLSLC:CELL=V2263C,SCTYPE=OL,CHTYPE=BCCH,ACL=A1;
RLSLC:CELL=V2263C,SCTYPE=OL,CHTYPE=SDCCH,ACL=A1;
RLSLC:CELL=V2263C,SCTYPE=OL,CHTYPE=TCH,ACL=A1,LAV=16;
60
2GHO_Script.txt
2GHI_Script.txt
3GHO_Script.txt
3GDR_RNC17_Scrip
t.txt
MBC_2263&5589_S
cript.txt
61
9 FAULT CODE LIST
62