Documente Academic
Documente Profesional
Documente Cultură
0
4
3
31
23
2
2
33
29
21010101
2s
4
4
Yes
5
10
60
60
60
60
No
Parameter Name Object Name HW setting range HW default value Ericsson
NetWork Optimization Index of Original Cell Basic Parameters 0~2048 cell specific
Name of Original Cell Basic Parameters A string of 32 characters cell specific
Allow Dynamic Voltage Adjustment Basic Parameters Yes,No No Yes
Allow Dynamic Shutdown of TRX Power Amplifier Basic Parameters Yes,No No Yes
TRX Aiding Function Control Call Control TRX Aiding Not Allowed,
Allowed
Allowed
& Recover
& Recover
When
Allowed
Forbidden,
Check
& Recover
ResAllowed
Immediately
& Recover Immediate
Preference for 2G
Cell, Preference Preference for
Preference for 2G
TDD Inter-RAT HO Preference Handover Control for 3G Cell, 2G Cell By
Cell By Threshold
Preference for 2G Threshold
By Threshold
Load HO of OL Subcell to UL Subcell Enabled Handover Control Yes,No Yes Cell specific
Load HO From UL Subcell to OL Subcell Allowed Handover Control Yes,NO No Cell specific
En Iuo Out Cell Serious OverLoad Thred Handover Control 0100 90 90/cell specific
En Iuo Out Cell Low Load Thred Handover Control 0100 20 cell specific
Incoming-to-BSC HO Optimum Layer Handover Control Overlaid Subcell, Underlaid Subcell, No Preference
Underlaid Subcell
RX_LEV Hysteresis Handover Control 0-63 5 When the cell is a 5dual-timeslot cell, the default value is set to 0
RX_LEV for UO HO Allowed Handover Control Yes, No The default value is Yes
generally set to Yes. When the cell is a dual-ti
HwIII Down Link Power Control Adjust Period Power Control 0255 3 3
Power Control Algorithm Switch Power Control HWII Power Contrl, HWIII
HWII Power Contrl HWIII Power Control
Busy Threshold of TCH Traffic in Overlaid Subcell Channel Management0-100 50 cell specific
AMR TCH/H Prior Cell Load Threshold Channel Management099 40 cell specific
MAX Paging Message Number 0f Cell In Period Other Property 160 220
Interfere Band Stat Algorithm Type Other Property 0, 1 1 Interference Band Measurement Algorithm II
cell specific
cell specific
No
Yes
63
Yes
A5/0A5/2
Yes
Yes
Yes
No
Yes
Shall Use
0
No
No
Yes
6dB
50
2 Multiframe Period
1
11111111
No
50
Yes
0
15
63
31
23
15
63
31
23
010101
25
17
12
28
19
15
10010101
1
Different Band
No
No
No
No
No
Yes
0
0
15
+0dB
No
Yes
15
RSCP
Use Qsearch_I
15
Yes
Yes
20
No
00000
0000000000
4 Times
No
34
29
23
No
60
60
200
150
50
50
60
-110
180
101111
20
24
20
24
70
No
16
20
45
No
50
25
68
63
10
35
50
50
90
25
30
10
No
No
10
10
90
80
No
Yes
50
No
35
50
25
Preference for 2G Cell By Threshold
35
25
60
50
90/cell specific
cell specific
cell specific
10
40
15
Yes
cell specific
cell specific
Underlaid Subcell
System Optimization
61
No
61
cell specific
System Optimization
3
0
60
cell specific
10
No
No
Yes
Yes
Yes
80
25
20
15
10
25
70
90
10
60
60
60
60
40
41
42
43
44
45
46
47
48
49
50
60
55
No
10
10
10
10
10
10
10
10
60
60
61
Open
255
10
10
10
63
cell specific
cell specific
63
4
3
16
Yes
No
No
No
Yes
No
2
2
Close
3
4
NO
10
20
4
5
Yes
8
0
2
30
No
2
3
3
cell specific
10
Yes
Yes
Yes
Yes
Yes
No
Yes
No
No
No
No
No
Yes
0
0
13
13
12
12
14
14
14
14
18
18
13
13
12
12
14
14
14
14
18
18
16
2
3
25
33
18
25
Yes
16
10
2
0
Yes
25
45
18
25
95
Yes
cell specific
cell specific
Close
Close
80
80
60
cell specific
Yes
30
30
45
30
35
Yes
Yes
Yes
Yes
Yes
No
Not Support
Quality Preferred
Yes
60
cell specific
cell specific
26000
34000
10000
10
15000
1000
30000
25000
30000
5000
10000
10000
5000
3000
220
180
Forced turn-on
Yes
No
No
Yes
Yes
Maximum/Mean Value
1
1
No
15
Yes
Yes
Yes
360
360
5000
15
100
15
10
36671
NO
65535
20
48
90
98
104
108
115
90
Yes
0001110110
StartUp
Not Report
Invalid
10
3
20
Not Support
No handover between underlaid subcell and overlaid subcell
16
6
Not Support
Not Support
Not Support
MCS6
UNFIXED
MCS2
UNFIXED
8
LA
20
10
20
10
5
5
CS2
UNFIXED
20
10
20
10
5
5
CS1
UNFIXED
30
2
No preempt of CCHs
30
Only convert at UL
80
70
cell specific
cell specific
cell specific
Report the frequencies of six strongest cells
-110dB
2
2
2
NoExclusive
Permit
2dB
10sec
Yes
0
c31standard
2dB
No
No
6
16
14
13
12
20
20
7
7
7
7
0
1
4
1
0.96sec
15.36sec
0.24sec
-2db
10sec
10dB
60sec
type1
1
1
em0
Yes
Yes
Area specific
Packet access of levels 1-4
No
nc0
12
4
2
10
Four access pulses by default
8bit
4
500ms
500ms
Network Operation Mode II
0.6
14
10
10
pdch
2
Parameter Description
This parameter determines the actual coverage area of a cell. When the BTS receives a CHANNEL REQUEST message or a
HANDOVER ACCESS message, it compares the TA with the value of this parameter to determine whether channel assignment or
handover is performed in this cell.
Yes: It indicates that the TCH is immediately assigned when the SDCCH has no available resource during the processing of access
request. No: It indicates that only the SDCCH can be assigned.
Additional Cell Reselectiom Param Indication:If ACS=0,Invalid in SySTEM INFO=3,but works in SYSTEM INFO=4 to tell SYTEM INFO
4.IF ACS=1,tells it means that the MS should obtain PI and other parameters for calculating C2 from other bytes of system
information 7 and 8.
If this parameter is reasonably configured, the number of handovers can be reduced and a better cell can be assigned to.When PT
is set to 31, it becomes more difficult for an MS to access a cell when CRO increases
Cell Reselection Parameter:Indicates whether to perform C2-Based Cell reselection.When PI=1 MS will calculate C2 from SYSTEM
INFO and perform Cell Reselection.If PI=0 then C1=C2,Cell-Reselection will be based on C1
CELL_RESELECT_HYSTERESIS,As MS does not responds to Paging messages during Location Update,too much Cell-Selection will
lead to Connection
"Forced Periodic drop.If
Locationit too Low,Frequent
Update".T3212 Cell-Rselection
is used for Forced will OccurUpdate
Location causingofLoad onmobile
Every Signaling.Too High valueArea.Unit
in Cell-Coverage can causeidMS
6 t
minutes.
Paging MutiFrame period:Defines Period for sending PAGING REQUEST message for to same Paging-Subgroup,the number ofcell-
If any mobile failed to respond to Paging message for a long time it will be considered as "Off-Line",and if this mobile
4.75 Kbps-12.2 Kbps 12.2 Kbps, 10.2 Kbps, 7.95 Kbps, 7.40 Kbps, 6.70 Kbps, 5.90 Kbps, 5.15 Kbps, 4.75 Kbps,If only value is selscted
then AMR starting Mode(F) must be 0,If two are selected then AMR Starting Mode(F) must be 1.
This parameter must meet the following conditions:[ AMR DL Coding Rate adj.th2 (F) + AMR DL Coding Rate adj.hyst2 (F) ] < [AMR
DL Coding Rate adj.th3 (F)+ AMR DL Coding Rate adj.hyst3(F)]
This parameter must meet the following conditions:[ AMR DL Coding Rate adj.th2 (F) + AMR DL Coding Rate adj.hyst2 (F) ] < [AMR
DL Coding Rate adj.th3 (F)+ AMR DL Coding Rate adj.hyst3(F)]
This parameter must meet the following conditions:[ AMR DL Coding Rate adj.th1 (F) + AMR DL Coding Rate adj.hyst1 (F) ] < [AMR
DL Coding Rate adj.th2 (F)+ AMR DL Coding Rate adj.hyst2(F)]
This parameter must meet the following conditions:AMR DL Coding Rate adj.th2(F) < AMR DL Coding Rate adj.th3(F) [ AMR DL
Coding Rate adj.th2(F) + AMR DL Coding Rate adj.hyst2 (F) ] < [AMR DL Coding Rate adj.th3(F) + AMR DL Coding Rate adj.hyst3 (F)]
This parameter must meet the following conditions:AMR DL Coding Rate adj.th2(F) < AMR DL Coding Rate adj.th3(F) [ AMR DL
Coding Rate adj.th2(F) + AMR DL Coding Rate adj.hyst2 (F) ] < [AMR DL Coding Rate adj.th3(F) + AMR DL Coding Rate adj.hyst3 (F)]
This parameter must meet the following conditions:AMR DL Coding Rate adj.th1(F) < AMR DL Coding Rate adj.th2(F) [ AMR DL
Coding Rate adj.th1(F) + AMR DL Coding Rate adj.hyst1 (F) ] < [AMR DL Coding Rate adj.th2(F) + AMR DL Coding Rate adj.hyst2 (F)]
This parameter must meet the following conditions:[ AMR UL Coding Rate adj.th2 (F) + AMR UL Coding Rate adj.hyst2 (F) ] < [AMR
UL Coding Rate adj.th3 (F)+ AMR UL Coding Rate adj.hyst3(F)]
This parameter must meet the following conditions:[ AMR UL Coding Rate adj.th2 (F) + AMR UL Coding Rate adj.hyst2 (F) ] < [AMR
UL Coding Rate adj.th3 (F)+ AMR UL Coding Rate adj.hyst3(F)]
This parameter must meet the following conditions:[ AMR UL Coding Rate adj.th1 (F) + AMR UL Coding Rate adj.hyst1 (F) ] < [AMR
UL Coding Rate adj.th2 (F)+ AMR UL Coding Rate adj.hyst2(F)]
This parameter must meet the following conditions:AMR UL Coding Rate adj.th2(F) < AMR UL Coding Rate adj.th3(F) [ AMR UL
Coding Rate adj.th2(F) + AMR UL Coding Rate adj.hyst2 (F) ] < [AMR UL Coding Rate adj.th3(F) + AMR UL Coding Rate adj.hyst3 (F)]
This parameter must meet the following conditions:AMR UL Coding Rate adj.th2(F) < AMR UL Coding Rate adj.th3(F) [ AMR UL
Coding Rate adj.th2(F) + AMR UL Coding Rate adj.hyst2 (F) ] < [AMR UL Coding Rate adj.th3(F) + AMR UL Coding Rate adj.hyst3 (F)]
This parameter must meet the following conditions:AMR UL Coding Rate adj.th1(F) < AMR UL Coding Rate adj.th2(F) [ AMR UL
Coding Rate adj.th1(F) + AMR UL Coding Rate adj.hyst1 (F) ] < [AMR UL Coding Rate adj.th2(F) + AMR UL Coding Rate adj.hyst2 (F)]
12.2 Kbps, 10.2 Kbps, 7.95 Kbps, 7.40 Kbps, 6.70 Kbps, 5.90 Kbps, 5.15 Kbps, 4.75 Kbps,Default is 11100100,
Indicates Max No. of Assignment Retry times.Valid only when TCH Assignment Retry is Enabled.
In normal Assignment proceedure,after receiving "Assignment Failure" message from MS,BSc does not Inform this to MSC
immediately.Instead it Re-Assigns Radio Channel & Re-Origenates assignment Proceedure.Option Different Band can cause
Whether to disable all users in a particular cell to receive messages in DL,but MS in call can receive messages in DL
Whether to disable all users in a particular cell to send messages in DL.
This parameter is used to concurrently deliver the channel activation message and immediate assignment command message to
quicken
This parameter the processing
indicates whether toofenable
signaling.
the Thus the response
function speedisof
that the TCHH the network
adjusted is ensured.
according to Abis resources.
This parameter indicates whether the enhanced multi level precedence and preemption (eMLPP) function is allowed. The eMLPP
means that the network is allowed to use different policies such as queuing, preemption, and direct retry according to the calls
with different priorities when the network resources are seized.
This parameter indicates whether the reassignment function is allowed.
This parameter indicates the reporting threshold for TDD cells.When the receive level of the TDD cell in the measurement report
is greater than the value of this parameter, the measurement report is valid.After the valid measurement report is filtered, the
TDD cell joins in the cell priority rank
This parameter indicates the reporting offset for TDD cells.When ranking the priority of a TDD cell, it is recommended to first add
the value of this parameter to the receive level of it in the measurement report.
This parameter indicates whether the reassignment function is allowed.
If this parameter is set to Yes, the BSC originates a second assignment when the BSC receives the Assignment Failure message. If
this parameter is set to Yes, it is good to raise the call completion rate of the MS. If there are a lot of MS assignment failures,
The TDD cell can become a candidate cell only when the average receive level of the TDD cell is greater than the "FDD Q Offset" of
the serving cell.
This parameter indicates the reporting offset for 3G cells.When ranking the priority of a 3G cell, it is recommended to first add the
value of this parameter to the receive level of it in the measurement report.
This parameter indicates the report offset for 3G cells.
When ranking the priority of a 3G cell, it is recommended to first add the value of this parameter to the receive level of it in the
measurement report
This parameter indicates the reporting offset for DCS1800 cells.When ranking the priority of a GSM1800cell based on its frequency
band, it is recommended to first add the value of this parameter to the receive level of it in the measurement report
This parameter indicates the reporting offset for DCS1800 cells.When ranking the priority of a GSM1800cell based on its frequency
band, it is recommended to first add the value of this parameter to the receive level of it in the measurement report
This parameter indicates the reporting threshold for GSM900 cells.When ranking the priority of a GSM900 cell based on its
frequency band, it is recommended to first add the value of this parameter to the receive level of it in the measurement report
This parameter indicates the reporting offset for GSM900 cells.When ranking the priority of a GSM900 cell based on its frequency
band, it is recommended to first add the value of this parameter to the receive level of it in the measurement report.
This parameter indicates the threshold of level for cell reselection in connection mode.In connection mode, if the signal level in
the service cell is below (0-7) or above (8-15), the MS starts to search for 3G cells.
For example:If this parameter is set to 5 and the signal level in the service cell is below 5, the MS starts to search for 3G cells.
This parameter indicates the strength added to the received signal strength before the MS delivers the enhanced measurement
report
This parameter indicates whether a cell with invalid BISC is allowed in the measurement report
This parameter indicates whether the MS is allowed to search for a 3G cell when the BISC must be decoded
This parameter indicates one of the threshold of level for cell reselection in packet mode.In packet mode, if the signal level in the
service cell is below (0-7) or above (8-15), the MS starts to search for 3G cells.
This parameter indicates one of the threshold of level for the reselection of 3G cells. Only when the receive level of a 3G cell is
greater than FDD Qmin, the 3G cell can be one of the candidate cells for reselection.0= -20dB
1= -6dB
This parameter indicates the number of UTRAN FDD cells that a best cell list or a measurement report should include
This parameter indicates the strength added to the received signal strength before the MS delivers the enhanced measurement
report
Only when the average receive level of a 3G cells is FDD Q Offset greater than that of the current service cell, the 3G cell can
become a candidate cell
This parameter indicates the threshold of level for cell reselection in connection mode befour the BTS receives the Qsearch C.
This parameter indicates the threshold of level for cell reselection in idle mode.In idle mode, if the signal level in the service cell is
below (0-7) or above (8-15), the MS starts to search for 3G cells.
For example:If this parameter is set to 5 and the signal level in the service cell is below 5, the MS starts to search for 3G cells.
If the system information indicates "MBR", the MS reports the quantities of neighbor cells on different frequency bands.When the
MS reports the quantity of neighbor cells on the same frequency band with the serving cell, a maximum of the value of "Serving
Band Reporting" can be reported.
If a class 3 MS on the DCS1800 band does not receive the original power command after random access, the power that the MS
uses is the MS maximum transmit power level plus the power calculated from the power deviation. See protocol GSM 05.08
The MS does not receive the original power command after random access. This parameter indicates whether the power
deviation is added to the class 3 MS on the DCS1800 band on the basis of the maximum MS transmit power
This parameter is used for the MS to report neighboring cell explanation of multiple bands. It is sent in the system messages 2ter
and 5ter.0: The MS reports the measurement results of six neighboring cells known and permitted by the NCC at the bands with
the best signal regardless of the band at which the neighboring cell is located.
Use for Dual-Band support MS to inform that Dual Band is Supported. Invalid for Single-Band MS
determins the time of Disconnecting a call when MS fails to Decode SAACH sent by BTS,Once a dedicated channel is assigned a
Timer S is started. Every time BTS sussceesfully Decdes a SACCH,it Increments by 2 otherwise Decrement by 1. When this timer
For MSs whose access class is from 0 to 9, if the reaches
Emergent0 Radio Link will
Call Disable be Fail
is set to No, emergency calls are allowed.For MSs whose
access class is from 11 to 15, emergency calls are not allowed only when the access control bit is set to 0 and the Emergent Call
Disable is set to Yes
This parameter is used for load control. It determines whether the users of special access class are allowed to access the network.
This parameter is used to control the load. It determines whether the users of common access class are allowed to access the
network
This parameter indicates the maximum times for sending Channel Request messages by the MS during an immediate assignment.
This parameter indicates the maximum number of retransmissions of the immediate assignment message. When this number is
reached, no retransmission is performed
Within the period specified by this parameter, the immediate assignment message can be dispatched and retransmitted.
Otherwise, the message cannot be dispatched or retransmitted
When establishing LAPDm between the BTS and MS, the BTS sends frame I to the MS. When the MS detects error in the frame I,
the BTS should resend frame I.This parameter indicates the Max retransmit times of frame I on the FACCH (a full-rate channel).
When establishing LAPDm between the BTS and MS, the BTS sends frame I to the MS. When the MS detects error in the frame I,
the BTS should resend frame I.This parameter indicates the Max retransmit times of frame I on the FACCH (a full-rate channel).
When establishing LAPDm between the BTS and MS, the BTS sends frame I to the MS. When the MS detects error in the frame I,
the BTS should resend frame I.This parameter indicates the Max retransmit times of frame I on the SDCCH.
When establishing LAPDm between the BTS and MS, the BTS sends frame I to the MS. When the MS detects error in the frame I,
the BTS should resend frame I.This parameter indicates the Max retransmit times of frame I on the SACCH
When establishing LAPDm between the BTS and MS, the BTS sends frame I to the MS. When the MS detects error in the frame I,
the BTS should resend frame I.This parameter indicates the maximum retransmission times of frame I during the multi-frame
release.
When establishing LAPDm between the BTS and MS, the BTS sends frame I to the MS. When the MS detects error in the frame I,
the BTS should resend frame I.This parameter indicates the maximum retransmission times of frame I.
This parameter controls whether the BSC delivers the LAPDm N200 parameter to the BTS.
This parameter determines the expiry value of T200 when the SDCCH supports SAPI3 services.
This parameter determines the expiry value of T200 on the SACCH on the SDCCH
This parameter determines the expiry value of T200 on the SACCH over the Um interface when the TCH supports SAPI3 services
This parameter determines the expiry value of T200 on the SACCH over the Um interface when the TCH supports SAPI0 services
This parameter determines the expiry value of T200 on the FACCH or full-rate channel over the Um interface
This parameter determines the expiry value of T200 on the FACCH or full-rate channel over the Um interface
This parameter determines the expiry value of timer T200 on the SDCCH over the Um interface,T200 Prevents Dead-Lock on Data
Link Layer of Um Interface.two Entities use Acknowlege & Retransmission method. Whenever any one entity sends any message it
should have acknowlegment,Otherwise T200 will be Expired.
This is min Level of RACH upon which it will be accepted bythe network.If level is less than this thrsh then RACH will be disgarded.
the system can determine whether the received signal is the random access signal of the MS through the correlation of training
sequence TSC (41 bits) and can calculate the TA value.
TRX Aiding Not Allowed indicates that the TRX aiding function is not allowed.
The six bits, from the most significant one to the least significant one, each bit indicates whether the BSC supports the following
Indicates RLT of AMR Half Rate
When target cells are selected during direct retry, only the cells whose loads are smaller than or equal to the Directed Retry Load
Access Threshold are selected as candidate target cells
When the Assignment Cell Load Judge Enabled is set to Yes, the direct try flow is allowed if the following two conditions are met:
This parameter indicates the measurement time of the 3G better cell handover algorithm
If the Outgoing-RAT HO Allowed parameter is set to Yes and the Better 3G Cell HO Allowed parameter is set to Yes,better 3G cell
handover is triggered when the RSCP of a 3G neighboring cell is greater than RSCP Threshold for Better 3G CELL HO in a period.
When the Inter-RAT HO Preference is set to 2 (2G cells are preferentially selected according to the threshold), 3G cells are the
preferential selection for handover if the receive level of the first candidate 2G cell is smaller than or equal to HO Preference
Threshold for 2G Cell.
This parameter indicates whether a 2G cell or a 3G cell is preferentially selected during cell handover
A quick switchover can be initiated only when the path loss difference between chain-type adjacent cells and serving cells is not
smaller than the value of this parameter within a measurement period.
This parameter indicates the level value to punish the original cell afthe a quick handover is triggerd
This parameter indicates the length of time to punish the orignal cell after a quick handover is performed
When the received number of measurement reports is no larger than the "Neglected Number of Measurement Reports", the
measurement reports are not filtered and the quick handover is not decided either.
This parameter prevents you from making an incorrect switchover decision on the basis of an inaccurate measurement report.
This parameter indicates the number of measurement reports filtered after the BSC receives measurement reports from serving
cells
The triggering of quick switchover must conform to the P/N rule. That is, within P seconds, there must be N seconds in succession
when the triggering conditions are met: This parameter is applied in conjunction with the following parameters:Quick Handover
Up Trigger Level (dB) or Quick Handover Down Trigger Level (dB)
This parameter indicates the P mentioned previously. If the duration when the triggering conditions are met is not smaller than
the value of this parameter within the time preset by Quick Handover Static Time, quick switchover is triggered.
The quick switchover can be initiated only when the MS speed is greater than Quick Move Speed Thres within a measurement
period.This parameter is applied in conjunction with the following parameters:
The quick switchover can be initiated only when the downlink level of a serving cell is lower than Quick Handover Down Trigger
Level within a measurement period after the measurement reports of the cell are compensated.This parameter is applied in
The quick switchover can be initiated onlyconjunction with the
when the uplink levelfollowing parameters:
of a serving cell is lower than Quick Handover Up Trigger Level
within a measurement period after the measurement reports of the cell are filtered.This parameter is applied in conjunction with
the following parameters:
If the ratio of channel occupancy in overlaid subcell is greater than the value of this parameter, it is not allowed to make the load
handover from underlaid cell to overlaid cell in an enhanced dual-band network.
P/N criterion: In P measurement reports, N measurement results meet handover requirements. Handover is started.
In P measurement reports, N measurement results meet handover requirements. Handover is started.This parameter indicates
the P in P/N criterion
After the handover succeeds, handover is not allowed within the time this parameter sets.
This parameter indicates the lowest threshold of overlaid subcell level of the handover from underlaid subcell to overlaid subcell.
This parameter indicates the lowest threshold of overlaid subcell level of the handover from underlaid subcell to overlaid subcell
This parameter indicates the level step of the load handover from overlaid subcell to underlaid subcell
This parameter indicates the period of the hierarchical handover from underlaid subcell to overlaid subcell. When the ratio of
overlaid subcell cell channel occupancy is greater than the value of En Iuo Out Cell General OverLoad Threshold, all the calls in the
cell request for handover at the same time. The BSC load is sharply increased, Thus the call may drop because the target cell is
This parameter indicates whether the load handover from overlaid subcell to underlaid subcell is allowed.
If underlaid subcell load is higher than the value of Out Cell Serious OverLoad Threshold, the period of handover from underlaid
subcell cell to overlaid subcell cell is shortened by the value of Out Cell Serious OverLoad Threshold every second based on the
value of the Out Cell Load classification HO Period.
This parameter indicates the level step of the hierarchical handover from underlaid subcell to overlaid subcell
This parameter indicates the period of the hierarchical handover from underlaid subcell to overlaid subcell. When the ratio of
overlaid subcell cell channel occupancy is greater than the value of En Iuo Out Cell General OverLoad Threshold, all the calls in the
cell request for handover at the same time. The BSC load is sharply increased, Thus the call may drop because the target cell is
When the ratio of underlaid subcell channel occupancy is high, whether some calls in the overlaid subcell are allowed to be
handed over to the overlaid subcell.
To prevent ping-pong handover, the BSC determines whether the handover of the MS from overlaid subcell cell to underlaid
subcell cell based on the value of this parameter.Suppose the signal strength of serving cell is SS(s), and neighboring cell SS(n). If
the value of SS(s)-SS(n) is smaller than the value of Distance Between Out And Inn Cell boundary-Distance Hyst Between Out And
This parameter indicates the distance between the overlaid subcell and underlaid subcell. The value of this parameter is
comparative. The greater the value is, the longer the distance is.
If the current system flow level is greater than the value of this parameter, the handover between the overlaid subcell and
underlaid subcell because the underlaid subcell load is too high or too low, is not allowed.
If the ratio of the underlaid cell channel occupancy is greater than the value of this parameter, the period of handover from
underlaid subcell to overlaid subcell is reduced by the value of Out Cell Load HO Modify Step every second based on the value of
Out of
If the ratio Cell Load Classification
underlaid HO Period.
subcell channel Thus is
occupancy the handover
greater thanfrom underlaid
the value subcell
of this to the some
parameter, overlaid subcell
calls in thespeeds up.subcell
underlaid
are handed over to the underlaid subcell. Moreover, calls initiated in the overlaid subcell are preferably assigned to the overlaid
subcell.
This parameter indicates whether the channel request in the overlaid subcell is preferably assigned between overlaid subcell and
underlaid subcell according to the Out Cell Low Load Threshold.
This parameter indicates whether the access request initiated in the underlaid subcell is preferably assigned between overlaid
subcell cell and underlaid subcell cell according to the Out Cell Low Load Threshold.
If the underlaid subcell channel occupancy ratio is smaller than the value of this parameter, some calls of the overlaid subcell is
handed over to the underlaid subcell. Moreover, the MS that requests for the overlaid subcell channel is preferably assigned to
the underlaid subcell.
This parameter indicates whether the better 3G cell handover algorithm is allowed
During the decision of 3G better cell handover algorithm, 3G better cell handover is originated only when the period that meets
the conditions of the 3G better cell handover algorithm in the measurement period is greater than 3G Better Cell HO Valid Time
This parameter indicates the measurement time of the 3G better cell handover algorithm
If the Outgoing-RAT HO Allowed parameter is set to Yes and the Better 3G Cell HO Allowed parameter is set to Yes, better 3G cell
handover is triggered when the Ec/No of a 3G neighboring cell is greater than Ec/No Threshold for Better 3G CELL HO in a period.0-
49 with
If the Outgoing-RAT HO Allowed parameter 0 indicating
is set to Yes and-24
thedB and 63
Better 3Gindicating 0 dB parameter is set to Yes,better 3G cell
Cell HO Allowed
handover is triggered when the RSCP of a 3G neighboring cell is greater than RSCP Threshold for Better 3G CELL HO in a period.
When the Inter-RAT HO Preference is set to 2 (2G cells are preferentially selected according to the threshold), 3G cells are the
preferential selection for handover if the receive level of the first candidate 2G cell is smaller than or equal to HO Preference
Threshold for 2G Cell.
This parameter indicates whether a 2G cell or a 3G cell is preferentially selected during cell handover.
Received level threshold of the handover from the UL subcell to the OL subcell of the PS service in the PS concentric algorithm
Received level threshold of the handover from the OL subcell to the UL subcell of the PS service in the PS concentric algorithm
This parameter indicates the level step of the hierarchical handover from underlaid subcell to overlaid subcell.
When the ratio of overlaid subcell cell channel occupancy is greater than the value of En Iuo Out Cell General OverLoad Threshold
all the calls in the cell request for handover at the same time. The BSC load is sharply increased. Thus the call may drop because
If the the target
ratio of thecell is congested.
underlaid Therefore
cell channel the algorithm
occupancy of hierarchical
is greater handover
than the value of this is applied tothe
parameter, hand overof
period the calls in thehandover
hierarchical cell
from underlaid subcell to overlaid subcell is shorten. That is, the value of Out Cell Load HO Modify Step is reduced every second
based on the value of Out Cell Load Classification HO Period. Thus the handover from underlaid subcell to the overlaid subcell
If the ratio of the underlaid subcell channel occupancy is greater than the value of this parameter, some calls in the underlaid
subcell are handed over to the overlaid subcell.
If the ratio of the underlaid subcell channel occupancy is smaller than the value of this parameter, some calls in the overlaid
subcell are handed over to the underlaid subcell.
This parameter indicates the threshold of UL to OL handover failures.UL to OL handover is not allowed if the number of handover
failures reaches this threshold.
This parameter indicates the penalty level given to a target cell. A penalty level is given to a target cell to avoid further attempts
when a handover fails due to any of the following reasons:
After an OL to UL handover fails, no OL to UL handover request is allowed before the penalty time expires.
This parameter indicates the penalty time for forbidding ping-pong handovers. After an OL to UL handover is performed, UL to OL
handover
This parameter indicates the length of is not
a grade in levelallowed beforeUL
grade-based the
topenalty time expires.
OL handover. Thus, high-level calls are handed over with
higher priority.This parameter and Underlay HO Step Period control the level band of the step-by-step handover from underlaid
subcells
This parameter indicates the interval between to overlaid
two grades subcells handovers.When
of level-based together. multiple UL to OL handover requests
are initiated simultaneously, it is possible that calls with low level are handed over. This does not conform to the principle that the
call with the best quality should be handed over firstly. Thus, level grade-based handover is used to hand over high-level calls with
This parameter indicates whether the traffic in the underlaid subcell determines the Enhanced Concentric underlaid to overlaid
(UL to OL) handover and the Enhanced Concentric overlaid to underlaid handover.
This is one of the parameters that determine the regions of overlaid and underlaid subcells,When Enhanced Concentric Cell is
allowed, the regions are co-determined by RX_QUAL Threshold, UtoO HO Receive Level Threshold, OtoU HO Receive Level
This is one of the parameters that determine Threshold, TA Threshold,
the regions of overlaidand
andTAunderlaid
Hysteresis
subcells. When Enhanced Concentric Cell is
allowed, the regions are co-determined by RX_QUAL Threshold, UtoO HO Receive Level Threshold, OtoU HO Receive Level
Threshold, TA Threshold, and TA Hysteresis.
This parameter indicates the method of selecting an optimum layer for an incoming handover.
The default value is System Optimization. For a hybrid cell, the default value is Underlaid Subcell.The default value is System
Optimization.
This parameter For
indicates the a dual-timeslot
threshold extended
of overlaid cell or
cell-based a hybrid cell,
immediate the defaultTAvalue
assignment.If Pref is
ofUnderlaid Subcell
Imme-Assign Allowed is set to
Yes, the system prefers the channel in overlaid subcell while ACCESS_DELAY is smaller than TA Thrsh. of Imme- Assign pref.
Otherwise, the system prefers the channel in Underlaid subcell.
This parameter indicates whether access_delay is used in the channel request message for immediate assignment. When this
parameter is set to No, a channel in the underlaid subcell is assigned.
When the optimal layer is selected through system optimization, the current SDCCH level can be estimated (inserted/filtered)
based on the uplink measurement result in the previous SDCCH MR. Then, overlaid and underlaid subcells are allocated by
comparing
When this parameter
the optimal and the receive
layer is selected throughlevel of SDCCH,
system and bythe
optimization, comparing
current TA and level
SDCCH the TA threshold
can of optimum
be estimated assignment
(inserted/filtered)
based on the uplink measurement result in the previous SDCCH MR. Then, overlaid and underlaid subcells are allocated by
comparing
This this parameter
parameter with
indicates the the receive
method of TCHlevel of SDCCH,
assignment and by comparing
a concentric TA with
cell.System the TA threshold
Optimization: of optimum
The system assignment.
selects the optimum
serving layer according to the MR provided through the SDCCH.
This parameter indicates the duration when the conditions for a concentric cell handover are met within UO HO Watch Time.
This parameter indicates the duration during which the BSC counts the duration when the conditions for an concentric cell
handover are met to decide whether to trigger a concentric cell handover.
This is one of the parameters that determine the regions of overlaid and underlaid subcells.When Concentric Circles HO Allowed is
set to No, the regions are co-determined by RX_LEV Threshold, RX_LEV Hysteresis, RX_QUAL Threshold, TA Threshold, and TA
Hysteresis.
This is one of the parameters that determine the regions of overlaid and underlaid subcells.When Concentric Circles HO Allowed is
set to No, the regions are co-determined by RX_LEV Threshold, RX_LEV Hysteresis, RX_QUAL Threshold, TA Threshold, and TA
Hysteresis.
This is one of the parameters that determine the regions of overlaid and underlaid subcells.When Concentric Circles HO Allowed is
set to No, the regions are co-determined by RX_LEV Threshold, RX_LEV Hysteresis, RX_QUAL Threshold, TA Threshold, and TA
Hysteresis.
This is one of the parameters that determine the regions of overlaid and underlaid subcells. It is invalid when Enhanced
Concentric Cell is allowed.This is one of the parameters that determine the regions of overlaid and underlaid subcells. It is invalid
when Enhanced
This is one of the parameters that determine Concentric
the regions Cell
of overlaid is allowed.
and underlaid subcells. It is invalid when Enhanced
Concentric Cell is allowed:When Enhanced Concentric Cell is not allowed, the regions are co-determined by RX_LEV Threshold,
This parameter indicates the signalHysteresis,
RX_LEV intensity compensation between
RX_QUAL Threshold, TAthe overlaidand
Threshold, andTA
underlaid subcells.It equals the sum of
Hysteresis
power difference between overlaid and underlaid power amplifiers, insertion loss difference between combiners, path loss
difference caused by antennas, and path loss difference caused by frequencies.
This parameter indicates whether the TA is used to determine a Concentric Cell handover.
This parameter indicates whether the downlink receive level is used to determine a Concentric Cell handover
This parameter indicates whether the downlink receive quality is used to determine a Concentric Cell handover
This parameter indicates whether an underlay (UL) to overlay (OL) handover is allowed
The load threshold for the tight BCCH handover. To initiate the intra-cell tight BCCH handover, the load should be greater than the
threshold.
Signal quality threshold for the tight BCCH handover. To initiate the intra-cell tight BCCH handover, the downlink receiving quality
This parameter indicates the K offset used for Kshould be lower
Ordering.To thanthe
reduce theping-pong
threshold effect during switchover, the BSC first deducts
K Bias from the actual downlink receiving level of a candidate cell. Then, the BSC performs K ordering over the downlink receiving
level of the candidate cell.
This parameter indicates the expected uplink receive level on a new channel after an MS is handed over to a new cell.
This parameter indicates the period during which penalty is performed on the neighboring cells of the fast moving MS.During this
period, penalty on the neighboring cells (on only the other three layers except the umbrella layer) of fast moving MS is valid.
This parameter indicates the penalty given to the level in a neighboring cell when an MS is moving fast.Only the cells in the
umbrella layer can give penalty to the cells in other three layers.
This parameter indicates the period for judging whether two continuous intra-cell handovers are consecutive
This parameter indicates the timer that starts when the threshold of maximum consecutive intra-cell handovers is reached.Intra-
cell handovers is allowed only when the timer expires
This parameter indicates the maximum number of consecutive intra-cell handovers allowed.If the interval of two continuous intra-
cell handovers is less than a specified threshold, the two handovers are regarded as consecutive handovers.
This parameter indicates the threshold for judging whether an MS moves fast across a cell.The threshold is obtained based on the
cell radius and specified velocity.
Suppose that the actual number of the micro cells that the MS fast crosses is N.According to the P/N rule,when the MS fast
crosses N ones among the P micro cells, a fast moving handover is triggered by the BSC when this parameter satisfies the required
conditions.
During the moving, the MS passes P micro cells.According to the P/N rule, when the MS fast crosses N ones among the P micro
cells, the BSC starts to trigger a fast-moving micro cell handover.
During the hierarchical load switchover, the load switchover band starts from Edge HO DL RX_LEV Threshold and a Load HO Step
Level is added to the upper threshold of the load switchover band every one Load HO Step Period. In this way, the BSC conducts
switchover levelisbynot
If a cell load level. Finally,
smaller thanallLoad
the calls with the receiving
HO Threshold, levelwith
all the calls of the
thiscurrent serving
cell as the cell cell
serving ranging
sendfrom Edge HO
switchover DL RX_LEV
requests
simultaneously. As a result, the system load soars.In serious situations, the congestion may occur to this cell, thus leading to call
drop. To avoidofcall
The setting thisdrop, the BSCis uses
parameter the hierarchical
relevant with Edge HO load
DL switchover algorithmuser
RX_LEV Threshold.A to control the number
is allowed ofload
to initiate usersswitchover
who experience
only
when the receiving level of the user's current serving cell is within the range from Edge HO DL RX_LEV Threshold to Edge HO DL
RX_LEV on,
When the load handover is switched Threshold + Load HO Bandwidth.
it is recommended that the Load HO Threshold is set to 85.
The cell load refers to TCH usage.
When the cell load exceeds the value of Load HO Threshold, the BSC starts the load handover. That is, the BSC starts the load
When the load handover is switched on, it is recommended that the Load HO Threshold is set to 85.When the cell load exceeds
the value of Load HO Threshold, the BSC starts the load handover. That is, the BSC starts the load handover after the TCH in the
cell are proportionally occupied.
System Flux Threshold for Load HO is obtained based on message load, CPU load, and FID queuing load. The system flow level is
the current flow control level of the system. 0-11: There are 12 flow control levels.Level 11 is the highest and level 0 is the lowest.
This parameter indicates the urgent switchover uplink quality control for the AMR HR service.The values of this parameter match
quality levels 0-7 multiplying 10. The urgent switchover is triggered only when the uplink receiving quality of the MS is greater
This parameter indicates the than theswitchover
urgent switchoverdownlink
threshold, that control
quality is, the receiving quality
for the AMR HR is poor.
service.The values of this parameter
match quality levels 0-7 multiplying 10. The urgent switchover is triggered only when the downlink receiving quality of the MS is
This parameter indicates thegreater
urgentthan the switchover
switchover threshold,
uplink quality thatfor
control is, the
the AMR
receiving quality is poor.
FR service.The values of this parameter match
quality levels 0-7 multiplying 10.The urgent switchover is triggered only when the uplink receiving quality of the MS is greater than
the switchover
This parameter indicates the urgent switchoverthreshold, that is, control
downlink quality the receiving
for thequality
AMR FR is poor.
service. The values of this parameter
match quality levels 0-7 multiplying 10.The urgent switchover is triggered only when the downlink receiving quality of the MS is
When determining whethergreater than
to initiate the switchover
interference threshold,
switchover, thethat is, the
system receiving
compares quality
the is poor.
difference between the receiving quality
of the MS and this parameter with the switchover threshold.For the AMR calls, this parameter, together with RXQUALn, is used in
interference handover decision. An uplink interference handover is easily triggered if this parameter is set to a smaller value.
Quality threshold 12 for the interference handover of non-AMR FR voice services. The value corresponds to (quality level 0-7) x 10.
Quality threshold 11 for the interference handover of non-AMR FR voice services. The value corresponds to (quality level 0-7) x 10.
Quality threshold 10 for the interference handover of non-AMR FR voice services. The value corresponds to (quality level 0-7) x 10.
Quality threshold 9 for the interference handover of non-AMR FR voice services. The value corresponds to (quality level 0-7) x 10.
Quality threshold 8 for the interference handover of non-AMR FR voice services. The value corresponds to (quality level 0-7) x 10.
Quality threshold 7 for the interference handover of non-AMR FR voice services. The value corresponds to (quality level 0-7) x 10.
Quality threshold 6 for the interference handover of non-AMR FR voice services. The value corresponds to (quality level 0-7) x 10.
Quality threshold 5 for the interference handover of non-AMR FR voice services. The value corresponds to (quality level 0-7) x 10.
Quality threshold 4 for the interference handover of non-AMR FR voice services. The value corresponds to (quality level 0-7) x 10.
Quality threshold 3 for the interference handover of non-AMR FR voice services. The value corresponds to (quality level 0-7) x 10
Quality threshold 2 for the interference handover of non-AMR FR voice services. The value corresponds to (quality level 0-7) x 10.
Quality threshold 1 for the interference handover of non-AMR FR voice services. The value corresponds to (quality level 0-7) x 10
This parameter indicates the upper threshold of consecutive MRs containing no downlink measurement result for a call.Each call
is configured with a global timer, which counts the number of consecutive MRs containing no downlink measurement. When the
timer exceeds this threshold, the handover is disabled and the timer is reset.
This parameter indicates the uplink receive quality threshold of triggering an emergency handover when no measurement result
on downlink channels is contained in the MR.
This parameter is used to control the handover algorithm without downlink measurement report.If this parameter is set to 0, the
no handover algorithm without downlink measurement report is disabled. Therefore, handover decision without downlink
measurement
This parameter indicates the general trend report is not
of a cell on receiving allowed
levels withininathis cell You can set this parameter for the filter
period.
when the levels of a cell plunge.If you attempt to initiate the switchover upon quick level decrease, the decrease trend of cell
Theselevels must beare
parameters increasingly remarkable
used for the as theoffilter
configuration parameter
the fast B becomes
drop filter. They aregreater.
used inThis parameter
conjunction should
with be applied
the filter in B,
parameter
which are 9 parameters in total as filter parameters. In the program, 10 is deducted from the actual values of A1-A8.C1(nt) = A1 x
C(nt) + A2 x C(nt-t) + A3 x C(nt-2t) + ... + A8 x C(nt-7t), where:
These parameters are used for the configuration of the fast drop filter. They are used in conjunction with the filter parameter B,
which are 9 parameters in total as filter parameters.
These parameters are used for the configuration of the fast drop filter. They are used in conjunction with the filter parameter B,
which are 9 parameters in total as filter parameters.
These parameters are used for the configuration of the fast drop filter. They are used in conjunction with the filter parameter B,
which are 9 parameters in total as filter parameters.
These parameters are used for the configuration of the fast drop filter. They are used in conjunction with the filter parameter B,
which are 9 parameters in total as filter parameters.
These parameters are used for the configuration of the fast drop filter. They are used in conjunction with the filter parameter B,
which are 9 parameters in total as filter parameters.
These parameters are used for the configuration of the fast drop filter. They are used in conjunction with the filter parameter B,
which are 9 parameters in total as filter parameters.
These parameters are used for the configuration of the fast drop filter. They are used in conjunction with the filter parameter B,
which are 9 parameters in total as filter parameters.
This parameter indicates the uplink receive quality threshold of triggering an emergency handover.When the receive quality of
the uplink is greater than UL Qual Threshold, an emergency handover is triggered due to bad quality.When frequency hopping or
DTXdownlink
This parameter indicates the of the cell is enabled,it
receive qualityisthreshold
recommended that you
of triggering an set this parameter
emergency to 70
handover.When the receive quality of
the downlink is greater than DL Qual Threshold, an emergency handover is triggered.When frequency hopping or DTX of the cell is
enabled,
This it the
is one of is recommended thatdetermine
parameters that you set this
theparameter
regions oftooverlaid
70. Whenandan emergency
underlaid handover isConcentric
subcells.When triggered, inter-cell
Circles HOhandover
Allowed is
set to No, the regions are co-determined by RX_LEV Threshold, RX_LEV Hysteresis, RX_QUAL Threshold, TA Threshold, and TA
Hysteresis.
By setting this parameter, you can select values from a measurement report. If the sender uses DTX when this parameter is set to
Open, select SUB from measurement reports. Otherwise, select FULL from measurement reports
This parameter indicates the length of the penalty timer for handover failure between adjacent cells due to incorrect data
configuration.
This parameter indicates the length of the penalty timer for handover failure between adjacent cells due to failed air interface
connection.
This parameter indicates the length of the penalty timer for handover failure between adjacent cells due to cell congestion
This parameter indicates the length of the filter on the NBR_RCVD_BLOCK traffic channel when the measurement report type is
EMR.By setting this parameter, you can use NBR_RCVD_BLOCK of multiple EMRs, thus avoiding inaccuracy owing to the use of
only one EMR signaling channel when the measurement report type is
This parameter indicates the length of the filter on the NBR_RCVD_BLOCK
EMR.By setting this parameter, you can use NBR_RCVD_BLOCK of multiple EMRs, thus avoiding inaccuracy owing to the use of
onlyto
This parameter determines the penalty time for AMR full rate one EMR.
half rate (FR-to-HR) handovers. Before the timer expires, no AMR
FR-to-HR handover request is allowed if the previous full-half handover fails due to channel unavailability or channel mismatch.
This parameter indicates the length of the filter on the REP_QUANT voice channel when the measurement report type is EMR.By
setting this parameter, you can use REP_QUANT of multiple EMRs, thus avoiding inaccuracy owing to the use of only one EMR
This parameter indicates the length of the filter on the REP_QUANT signaling channel when the measurement report type is
EMR.By setting this parameter, you can use REP_QUANT of multiple EMRs, thus avoiding inaccuracy owing to the use of only one
EMR.
This parameter indicates the number of previous measurement reports obtained when you average CV_BEP of the traffic channel
during the process for averaging EMRs
This parameter indicates the number of previous measurement reports obtained when you average CV_BEP of the signaling
channel during the process for averaging EMRs.By setting this parameter, you can use CV_BEP of multiple EMRs, thus avoiding
This parameter indicates the number ofinaccuracy owing to the reports
previous measurement use of only one EMR.
obtained when you average MEAN_BEP of the traffic
channel during the process for averaging.By setting this parameter, you can use MEAN_BEP of multiple EMRs, thus avoiding
inaccuracy
This parameter indicates the number of previous owing to thereports
measurement use of obtained
only one EMR.
when you average MEAN_BEP of the signaling
channel during the process for averaging EMRs.By setting this parameter, you can use MEAN_BEP of multiple EMRs, thus avoiding
inaccuracy owing to the use of only one EMR.
This parameter indicates the penalty time given to the original serving cell where emergency handover is performed due to TA.
This parameter indicates the penalty level given to the original serving cell where emergency handover is performed due to
TA.After emergency handover is performed due to TA, the receive level of the original serving cell is decreased by the penalty
level. Thus, other cells are given higher priority and handover to the original serving cell is not allowed.
This parameter indicates the penalty time given to the original serving cell where emergency handover is performed due to bad
quality.
After emergency handover is performed due to bad quality, the receive level of the original serving cell is decreased by the
penalty level. Thus, other cells are given higher priority and handover to the original serving cell is not allowed.
This parameter indicates the penalty level given to a target cell.A penalty level is given to a target cell to avoid further attempts
when a handover fails due to any of the following reasons:
This parameter indicates the number of previous measurement reports obtained when you average the timing advances during
the process for averaging the measurement reports.
This parameter indicates the number of previous measurement reports obtained when you average the signal strength of
adjacent cells during the process for averaging measurement reports
This is Filter Length(How many MR are to be taken) Network will require for decision of SDCCH Qual HO.TVH HO will initiate
depending upon specific no of MR.
This is Filter Length(How many MR are to be taken) Network will require for decision of SDCCH HO.TVH HO will initiate depending
upon specific no of MR.
This is Filter Length(How many MR are to be taken) Network will require for decision of TCH Qual HO.TVH HO will initiate
depending upon specific no of MR.
This is Filter Length(How many MR are to be taken) Network will require for decision of TCH HO.TVH HO will initiate depending
upon specific no of MR.
This parameter indicates the number of measurement reports allowed to be continuously lost in the interpolation calculation.
If the number of continuously lost measurement reports is not larger than the value, the value of the lost measurement reports is
This parameter is used to select the candidate cells during directed retry
After the MR is preprocessed by BTS, the BTS transfers the preprocessed MR to the BSC.This parameter indicates the frequency
that the BTS transfers the preprocessed MR to the BSC
This parameter indicates whether the original BS/MS power class is transferred to the BSC
Determines whether MS will process measurement Report & then send it or just send MR to BTS. If it is Pre-process then MS must
also send Originl MR with that MR
Determines whether MS will process measurement Report & then send it or just send MR to BTS. If it is Pre-process then MS must
also send Originl MR with that MR
This parameter indicates whether the MS uses the optimum transmit power to access a new channel after the handover.
This parameter indicates whether penalty is given to certain cells, including target cells where handover fails and serving cells
where handover is triggered due to excessive TA or poor signal strength.
This parameter indicates whether an inter-BSC SDCCH handover is allowed. An inter-BSC SDCCH handover is triggered when an MS
succeeds in requesting SDCCH but fails to request TCH in a BSC.
This parameter indicates the minimum interval between two consecutive emergency handovers.
This parameter is used to prevent Ping-Pong HO due to any reason. Any kind of HO is not activated after the time of first HO
This parameter indicates the duration of a timer, which starts upon new SDCCH assignment and triggers handover upon timeout.
To avoid
To indicate incorrectofhandovers
the duration caused
a timer, which by the
starts inaccurate
upon new TCHmeasurements
assignment andattriggers
early stage of callupon
handover establishment.
timeout. To avoid
incorrect handovers caused by the inaccurate measurements at early stage of call establishment.
This parameter indicates whether to switch on/off the concentric DTCB handover.
This parameter indicates P of the P/N criterion for the tight BCCH handover
This parameter indicates N of the P/N criterion for the tight BCCH handover.
This parameter indicates whether an quick handover is allowed.
This parameter indicates the threshold of TCHH to TCHF handover.
This parameter indicates the threshold of a handover from full rate data TCH (TCHF) to half rate data TCH (TCHH).
This parameter indicates the period that satisfies full rate to half rate handover.
This parameter indicates the time threshold that satisfies full rate to half rate handover.
To indicate whether the handover between the full rate and half rate is allowed or not.
This parameter indicates the lower threshold of downlink receive level when a cell becomes a candidate cell .
This parameter indicates the lower threshold of Uplink receive level when a cell becomes a candidate cell .
This parameter indicates the hysteresis of an inter-layer or inter-priority handover. It is used to avoid inter-layer ping-pong
This parameter indicates the Threshold of an inter-layerhandovers.
or inter-priority handover. It is used to avoid inter-layer ping-pong
handovers.
To indicate the UL receive level threshold of an edge handover. An edge handover will be triggered if the uplink receive level is
constantly lower than "Edge HO UL RX_LEV Thrsh." for a period longer than Edge HO Valid Time(s) within Edge HO Watch Time(s).
To indicate whether an interference handover is allowed. An interference handover is triggered when the receive level is higher
than the receive threshold, but the transmission quality is lower than the handover triggering threshold
This parameter indicates whether a concentric circle handover is allowed ( 900 to 1800 & 1800 to 900 )
The parameter indicates whether a Timing Advance (TA) handover is allowed. A TA handover is triggered when the TA is higher
than the triggering threshold
To indicate whether a Bad quality handover is allowed. BQ handover is triggered when Bit Error Ratio (BER) over uplink/downlink
channels is higher than the triggering threshold.
To indicate whether a fringe handover is allowed. A fringe handover is used to prevent call drops in cell edges and initiated when
the downlink level in the serving cell is lower than Edge HO DL RX_LEV Threshold or the uplink level in the serving cell is lower
than Edge HO UL RX_LEV Threshold.
The parameter indicates whether the layer level handover is allowed . To guide the traffic to the cell that has high priority.
To indicate whether a power budget handover is allowed. Calculations for the power budget handovers are based on path loss
and search for desired cell in real time and the cell must provide less path loss and other requirements.
The parameter indicates whether the emergency handover algorithm is allowed. The emergency handover algorithm is used to
prevent call drops when the receive level of the MS drops rapidly
This parameter indicates whether a fast moving handover is allowed . The fast moving handover enables a fast moving MS to hand
over rapidly
This parameter indicates whether a traffic to a macro
load-sharing cell, is
handover thus reducing
allowed handovers.functions only within the same BSC or
. Load-sharing
in cells of the same layer. It applies to only TCH.
This parameter indicates whether the sequence of candidate cells is adjusted . After the sequence is adjusted, the handover
within the same BSC/MSC takes priority
To indicate the receive quality gain when the number of frequency hopping is 8. The receive quality is brought out when the cell is
configured with the frequency hopping. BSC performs power control based on the gain.
To indicate the receive quality gain when the number of frequency hopping is 7. The receive quality is brought out when the cell is
configured with the frequency hopping. BSC performs power control based on the gain.
To indicate the receive quality gain when the number of frequency hopping is 6. The receive quality is brought out when the cell is
configured with the frequency hopping. BSC performs power control based on the gain.
To indicate the receive quality gain when the number of frequency hopping is 5. The receive quality is brought out when the cell is
configured with the frequency hopping. BSC performs power control based on the gain.
To indicate the receive quality gain when the number of frequency hopping is 4. The receive quality is brought out when the cell is
configured with the frequency hopping. BSC performs power control based on the gain.
To indicate the receive quality gain when the number of frequency hopping is 3. The receive quality is brought out when the cell is
configured with the frequency hopping. BSC performs power control based on the gain.
To indicate the receive quality gain when the number of frequency hopping is 2. The receive quality is brought out when the cell is
configured with the frequency hopping. BSC performs power control based on the gain.
To indicate the receive quality gain when the number of frequency hopping is 1. The receive quality is brought out when the cell is
configured with the frequency hopping. BSC performs power control based on the gain.
This parameter indicates the maximum permissible adjustment step when the BSC increases uplink transmit power according to
signal quality.
This parameter indicates the maximum permissible adjustment step when the BSC reduces uplink transmit power according to
signal quality.
This parameter indicates the lower threshold of downlink power control quality level of AMR half-rate traffic channel. When the
receive quality is lower than the value of this parameter, the BSC performs HW III power control.
This parameter indicates the upper threshold of uplink power control quality level of AMR half-rate traffic channel. When the
receive quality is higher than the value of this parameter, the BSC performs HW III power control.
This parameter indicates the lower threshold of downlink power control quality level of AMR full-rate traffic channel. When the
receive quality is lower than the value of this parameter, the BSC performs HW III power control.
This parameter indicates the upper threshold of uplink power control quality level of AMR full-rate traffic channel. When the
receive quality is higher than the value of this parameter, the BSC performs HW III power control.
This parameter indicates the lower threshold of downlink power control quality level of half-rate traffic channel. When the
receive quality is lower than the value of this parameter, the BSC performs HW III power control.
This parameter indicates the upper threshold of uplink power control quality level of half-rate traffic channel. When the receive
quality is higher than the value of this parameter, the BSC performs HW III power control.
This parameter indicates the lower threshold of downlink power control quality level of full-rate traffic channel. When the receive
quality is lower than the value of this parameter, the BSC performs HW III power control.
This parameter indicates the upper threshold of uplink power control quality level of full-rate traffic channel. When the receive
quality is higher than the value of this parameter, the BSC performs HW III power control.
This parameter indicates the lower threshold of uplink power control signal level. When the receive level is smaller than the value
of this parameter, the BSC performs the HW III power control.
This parameter indicates the upper threshold of uplink power control signal level. When the receive level is higher than the value
of this parameter, the BSC performs the HW III power control.
This parameter indicates the step ratio of the quality level adjusted by uplink power control.
This parameter indicates the step ratio of the signal strength adjusted by uplink power control
This parameter indicates the period of the filtering of quality level smooth window through uplink power control.
This parameter indicates the period of the filtering of signal level smooth window through uplink power control.
This parameter indicates the period of the filtering quality level index through uplink power control.
This parameter indicates the period of the filtering of signal level index through uplink power control.
This parameter indicates the maximum permissible adjustment step during up power control adjustment based on signal quality.
This parameter indicates the maximum permissible adjustment step during down power adjustment based on signal quality.
This parameter indicates the lower threshold of downlink power control quality level of AMR half-rate traffic channel. When the
receive quality is lower than the value of this parameter, the BSC performs HW III power control.
This parameter indicates the upper threshold of downlink power control quality level of AMR half-rate traffic channel. When the
receive quality is higher than the value of this parameter, the BSC performs HW III power control.
This parameter indicates the lower threshold of downlink power control quality level of AMR half-rate traffic channel. When the
receive quality is lower than the value of this parameter, the BSC performs HW III power control.
This parameter indicates the upper threshold of downlink power control quality level of AMR full-rate traffic channel. When the
receive quality is higher than the value of this parameter, the BSC performs HW III power control.
This parameter indicates the lower threshold of downlink power control quality level of half-rate traffic channel. When the
receive quality is lower than the value of this parameter, the BSC performs HW III power control.
This parameter indicates the upper threshold of downlink power control quality level of half-rate traffic channel. When the
receive quality is higher than the value of this parameter, the BSC performs HW III power control.
This parameter indicates the lower threshold of downlink power control quality level of full-rate traffic channel. When the receive
quality is lower than the value of this parameter, the BSC performs HW III power control.
This parameter indicates the upper threshold of downlink power control quality level of full-rate traffic channel. When the receive
quality is higher than the value of this parameter, the BSC performs HW III power control.
This parameter indicates the lower threshold of downlink power control signal level. When the receive level is lower than the
value of this parameter, the BSC performs the downlink power control.
This parameter indicates the upper threshold of downlink power control signal level. When the receive level is higher than the
value of this parameter, the BSC performs the downlink power control.
This parameter indicates the step ratio of the quality level adjusted by downlink power control.
This parameter indicates the step ratio of the signal strength adjusted by downlink power control.
This parameter indicates the smooth window filter length of quality level through downlink power control.
This parameter indicates the smooth window filter length of signal level through downlink power control.
This parameter indicates the exponent filter length of quality level through downlink power control.
This parameter indicates the exponent filter length of signal level through downlink power control.
This parameter indicates the maximum number of allowed discarded TCH measurement reports in a power control period.
This parameter indicates the maximum number of allowed discarded SDCCH measurement reports in a power control period.
This parameter indicates the shortest interval between two continuous downlink power control commands
This parameter indicates the shortest interval between two continuous uplink power control commands.
When the number of discarded measurement reports within the power control period is greater than the value of this parameter,
the BSC stops power control.
This parameter indicates the maximum range of dynamic power adjustment for the BTS . If the value of this parameter is too
small, the dynamic power adjustment capability of the BTS is lowered.
During downlink power control, when the quality of received downlink signals is larger than or equal to DL Qual Bad
TrigThreshold, the actual value of DL RX_LEV Upper Threshold is the one plus the value of DL Qual Bad Up LEVDiff.
During downlink power control, when the quality of received downlink signals is larger than or equal to this trigger threshold , the
actual value of DL RX_LEV Upper Threshold is the one plus the value of DL Qual Bad Up LEVDiff in the data configuration
During downlink power control, when the quality of received downlink signals is larger than or equal to DL Qual Bad
TrigThreshold , the actual value of DL RX_LEV Upper Threshold is the one plus the value of DL Qual Bad Up LEVDiff.
During uplink power control, when the quality of received uplink signals is larger than or equal to this trigger threshold , the
actual value of DL RX_LEV Upper Threshold is the one plus the value of DL Qual Bad Up LEVDiff in the data configuration
This parameter determines the maximum permissible adjustment step during power adjustment based on the quality.
This parameter determines the maximum permissible adjustment step during up power adjustment based on the level.
This parameter determines the maximum permissible adjustment step during power adjustment based on the quality.
In the Huawei II power control algorithm, three quality zones (0, 1-2, 3) are defined according to the quality of received signals. A
maximum permissible down power adjustment step is set for each quality zone. This parameter determines the maximum power
adjustment step permitted by the level down power control when the RQ value is quality zone 2 (quality value3) during down
This parameter determines the maximum power adjustment step permitted by the level down power control when the RQ value
is quality zone 1 (0 < quality value < 3) during down power adjustment based on level.
This parameter determines the maximum power adjustment step permitted by power control when the RQ value is 0.
When the power control step is calculated according to the signal quality, the quality of the received signal has an upper
threshold and a lower threshold. When the signal quality exceeds the upper threshold or is below the lower threshold, power
control is performed. This parameter determines the downlink quality lower threshold for power control
This parameter determines the downlink quality upper threshold for power control.
This parameter determines the lower threshold of the downlink signal for the AMR power control. If the signal level is below this
threshold, calculate an increased value (= (AMR DL RX_LEV Upper Threshold +AMR DL RX_LEV Lower Threshold)/2 - Received
Level).
This parameter determines the upper threshold of the downlink signal for the AMR power control. If the signal level exceeds this
threshold, calculate a decreased value (= Received Level- (AMR DL RX_LEV Upper Threshold +AMR DL RX_LEV Lower
Threshold)/2).
This parameter determines the uplink quality lower threshold for the AMR power control.
This parameter determines the uplink quality upper threshold of the stable state quality zone.
This parameter determines the lower threshold of the uplink signal for power control. If the signal level is below this threshold,
calculate an increased value (= (AMR UL RX_LEV Upper Threshold +AMR UL RX_LEV Lower Threshold)/2 - Received Level).
This parameter determines the upper threshold of the uplink signal for power control. If the signal level exceeds this threshold,
calculate a level adjustment value (=Received Level-(AMR UL RX_LEV Upper Threshold +AMR UL RX_LEV Lower Threshold)/2 ).
In Huawei II power control algorithm, the prediction function is added in the filter to compensate the dela of power adjustment.
This parameter determines the number of downlink measurement reports for prediction.
This parameter determines the number of uplink measurement reports for prediction
When this parameter is set to Yes, the Huawei II power control algorithm puts the received measurement reports in the
measurement report compensation queue and then records the change in transmit power based on the MS power and the BTS
When the network receives measurementpower reports, an average
in the value of
measurement downlink signal quality values in consecutive
report
measurement reports should be obtained to reflect the radio environment where the BTS locates. This parameter indicates the
number
When of measurement
the network reports in which
receives measurement the average
reports, of thevalue
an average downlink signalsignal
of uplink quality is taken
quality before
values BTS power adjustment.
in consecutive measurement
reports should be obtained to reflect the radio environment where the MS locates. This parameter indicates the number of
measurement reports in which the average of the uplink signal quality is taken before MS power adjustment.
This parameter indicates the number of measurement reports in which the average of the downlink signal strength is taken
before BTS power adjustment
This parameter indicates the number of measurement reports in which the average of the uplink signal strength is taken before
AMR MS power adjustment.
Minimum time interval between two continuous AMR power control commands
To indicate the maximum range of dynamic power adjustment for the BTS. Smaller the value, dynamic adjustment capability of
BTS is lowered.
During downlink power control, when the quality of received downlink signals is larger than or equal to DL Qual Bad
TrigThreshold, the actual value of DL RX_LEV Upper Threshold is the one plus the value of DL Qual Bad Up LEVDiff.
During downlink power control, when the quality of received downlink signals is larger than or equal to this trigger threshold, the
actual value of DL RX_LEV Upper Threshold is the one plus the value of DL Qual Bad Up LEVDiff.
During uplink power control, when the quality of received uplink signals is larger than or equal to UL Qual Bad TrigThreshold, the
actual value of UL RX_LEV Upper Threshold is the one plus the value of UL Qual Bad Up LEVDiff.
During uplink power control, when the quality of received uplink signals is larger than or equal to this trigger threshold, the actual
value of UL RX_LEV Upper Threshold is the one plus the value of UL Qual Bad Up LEVDiff in the data configuration.
This parameter determines the maximum permissible adjustment step during down power adjustment based on the quality of
received signals.
This parameter determines the maximum permissible adjustment step during up power adjustment based on the level.
This parameter determines the maximum permissible adjustment step during power adjustment based on the quality.
In the Huawei II power control algorithm, three quality zones (0, 1-2, 3) are defined according to the quality of received signals.
This parameter indicates the maximum power control step permitted when the received signals are within quality zone 2 (RQ
value 3) and when the power is lowered based on the level.
This parameter indicates the maximum power control step permitted when the received signals are within quality zone 1 (0 < RQ
value < 3) and when the power is lowered based on the level.
This parameter indicates the maximum power control step permitted when the received signals are within quality zone 2 (1< RQ
value <3) and when the power is lowered based on the level.
After the BSC delivers the power control command, it will be a period before the BSC receives an acknowledgement message. The
measurement reports lag behind the changes in the MS received level and in the MS received signal quality. Thus the power
adjustment is delayed. in a short period of time, the BSC samples several downlink measurement reports and performs weighted
This parameter indicates the number of uplink measurement reports predicted by the BSC. The value of the parameter equals the
previous number N.
If this parameter is set to Yes, the BSC or BTS puts the received measurement reports in the measurement report compensation
queue. Then record the change of transmit power based on the MS power and the BTS power in the measurement report. After
To reflect
values the current
are added radio environment
in the measurement where
report, MS locates,
compensate the BSS receive
received measurement
level value in the reports and
historical an average value
measurement ofbased
report uplinkon
signal quality is obtained in consecutive MR. This parameter indicates the number of measurement reports in which the average
of the downlink signal quality is taken before BTS power adjustment.
This parameter indicates the number of measurement reports in which the average of the uplink signal quality is taken before MS
power adjustment
This parameter indicates the number of measurement reports in which the average of the downlink signal strength is taken
before BTS power adjustment.
This parameter indicates the number of measurement reports in which the average of the uplink signal strength is taken before
MS power adjustment.
To indicate whether BSC applies HW III power control algorithm. Yes: BSC Applies; NO: BSC does not apply
In order to calculate the power control according to the signal quality, the quality of the received signal has upper threshold and
lower threshold. This parameter determines the downlink quality lower threshold for the power control.
This parameter determines the downlink quality upper threshold for the power control.
This parameter determines the lower threshold of the downlink signal for power control. If the signal level is below this threshold ,
calculate an increased value (= (DL RX_LEV Upper Threshold +DL RX_LEV Lower Threshold )/2 - Received Level).
This parameter determines the upper threshold of the downlink signal for power control. If the signal level exceeds this
threshold , calculate a decreased value (= Received Level - (DL RX_LEV Upper Threshold +DL RX_LEV Lower Threshold )/2).
This parameter determines the uplink quality lower threshold for the power control.
This parameter determines the uplink quality upper threshold of the stable state quality zone. The upper threshold is larger than
or equal to the lower threshold .
The step of power control is determined by UL RX_LEV Upper Threshold and UL RX_LEV Lower Thrsh. If the uplink signal strength
is within the range from UL RX_LEV Upper Threshold to UL RX_LEV Lower Thrsh, power control on the MS is not performed. If the
uplink signal strength is beyond the range, power control on the MS is performed.
If the uplink signal strength is within the range from UL RX_LEV Upper Threshold to UL RX_LEV Lower Thrsh, power control on the
MS is not performed. If the uplink signal strength is beyond the range, power control on the MS is performed.
Minimum time interval between two continuous power control commands
If the uplink received level difference of calls of the same timeslot exceeds threshold of the difference between uplink received
levels, the situation must be recorded.During the observation of N seconds, if this situation lasts P seconds, the call with the
highest
If the uplink received uplink signal
level difference of intensity in same
calls of the the timeslot should
timeslot be handed
exceeds over
threshold to another
of the timeslot.
difference between uplink received
levels, the situation must be recorded.During the observation of N seconds, if this situation lasts P seconds, the call with the
highest uplink signal intensity in the timeslot should be handed over to another timeslot.
The value is 0-1 in fact; however, RRM and CM are multiplied by 10 to prevent floating-point values.
This parameter indicates whether the BSC is allowed to assign the half-rate channels and full-rate channels to the MS according to
the channel seizure ratio of the underlaid subcell and overlaid subcell.
The BSC assigns channels in underlaid subcell to the MS in the concentric cell. If the channel seizure ratio of underlaid subcell is
higher than the value of this parameter, half-rate channels are assigned; if the channel seizure ratio of underlaid subcell is not
The BSC assigns channels inhigher thansubcell
overlaid the value of this
to the MS inparameter, full-rate
the concentric cell.channels are assigned.
If the channel seizure ratio of overlaid subcell is
greater than the value of this parameter, half-rate channels are assigned. If the channel seizure ratio of overlaid subcell is not
greater than the value of this parameter, full-rate channels are assigned.
This parameter indicates whether dynamic HSN is permissible to use. To reduce the inter frequency interference
This parameter indicates whether the BSC enables the function of FlexMAIO. When the frequency hopping and FlexMAIO are
enabled in a cell, part of the intra-frequency interferences can be avoided.
To control the Abis resource load threshold. When Abis resource load is lower than this threshold, full rate channel is assigned.
When the static Abis resource load is greater than the static Abis load threshold, half-rate channel is preferably assigned if the
dynamic Abis resource load is greater than the value of this parameter; full-rate channel is preferably assigned when if the
dynamic Abis resource load is not greater than the value of this parameter.
If the dynamic PDCHs configured in the cell are occupied by the PCU, the BSC periodically reclaims dynamic PDCHs from the PCU
when the CS services of the cell are overloaded.
The channel type to be assigned is decided according to the channel types that are allowed by the MSC and the percentage of
seized TCHs in the cell.
This parameter indicates whether the TCH /H prior function is allowed during the channel assignment.
This parameter indicates the duration after which the flow of updating the history channel priority starts.
This parameter indicates how many measurement reports are used to determine the quality of SDCCHs.
This parameter indicates how many measurement reports are used to determine the level of SDCCHs.
This parameter indicates how many measurement reports are used to determine the quality of TCHs .
This parameter indicates how many sequential measurement reports are used to determine the level of TCHs .
This parameter indicates the interference threshold of the downlink channel quality.
This parameter indicates the interference threshold of the downlink channel level.
This parameter indicates the interference threshold of the uplink channel quality. The higher the level, the greater the signal
strength is. The greater the quality, the lower the signal strength is.
This parameter indicates the interference threshold of the uplink channel level. The higher the level, the greater the signal
strength is. The greater the quality, the lower the signal strength is.
This parameter indicates whether the random selection of the channels as the start of the channel traversal is allowed.
This parameter indicates whether the factor of the history record priority is effective in the channel priority.
This parameter indicates whether the TRX priority factor is effective in the channel priority.
This parameter indicates whether the interference measurement of the occupied channels is allowed.
This parameter indicates whether the interference priority factor is effective in the channel priority. Yes: Effective; No: ineffective
This parameter indicates whether to turn on the switch for the tight BCCH algorithm, and thus controls whether to enable the
BCCH aggressive frequency reuse algorithm.
This parameter indicates whether the current cell supports the dynamic transmission diversity or dynamic PBT
This parameter sets the priority of different types in channel allocation. These types include:priority by capacity, priority by
quality, relative priority by PS domain, absolute priority by PS domain
This parameter indicates whether the channel rearrangement (two single TCHHs are rearranged as a TCHF) is allowed.
This parameter indicates the minimum time for the recovery of a TCH from an SDCCH .
This parameter indicates the maximum number of SDCCHs that can be configured in a cell.
When the number of idle SDCCHs in a cell is smaller than or equal to the value of this parameter, more TCHs in the cell are
changed into SDCCHs .
The BSC delivers the ChannelRelease message and the AMRHR encoding mode, and enables the T3109 (AMRHR) timer. If the BSC
receives the ReleaseIndication message before the T3109 (AMRHR) timer expires, the T3109 (AMRHR) timer stops; if the T3109
(AMRHR) timer expires, the BSC deactivates the channel.
The BSC delivers the ChannelRelease message and the AMRFR encoding mode, and enables the T3109 (AMRFR) timer. If the BSC
receives the ReleaseIndication message before the T3109 (AMRFR) timer expires, the T3109 (AMRFR) timer stops; if the T3109
(AMRFR) handover
The T3103 timer starts when the intra-BSC timer expires, the BSC
command is deactivates thewhen
sent and ends channel.
the handover is complete. If the timer
expires, the intra-BSC handover fails.
This parameter indicates the timer that the WaitIndcation information element carries when the BSC sends the Immediate
Assignment Reject message to the MS. The MS receiving the Immediate Assignment Reject message attempts to access the
network after the period specified by this parameter.
The T8 starts when the handover command is sent and ends when the successful handover message is received. If the timer
expires, the out-BSC handover is regarded as unsuccessful
The T3121 timer starts when the handover request is sent and ends when the handover complete message is received. If the timer
expires, the ClearReq message is sent.
The T3107 timer starts when the assignment command is sent and ends when the assignment complete message is sent. If the
timer expires, the assignment fails and the seized channels are released.
The T7 timer starts when the handover request message is sent and ends when the handover response message is reported. If the
timer expires, the outgoing BSC handover fails.
The T3103 timer starts when the intra-BSC handover command is sent and ends when the handover is complete. If the timer
expires, the intra-BSC handover fails.
This timer starts when the CR message is reported and ends when the CC message is received. If the timer expires, the seized
SDCCH is released.
If the timer expires, the seized SDCCH is released. If the reception of the EST IND message expires, the BSS releases the seized
SDCCH.
This parameter indicates the maximum number of paging messages that a cell is allowed to send within a statistical period.
This parameter indicates the average number of paging messages that a cell is allowed to send within a statistical period.
This parameter indicates the maximum number of messages in the buffer of the cell paging group packet when the Cell Paging
Message Group Packet Function Switch is turned on.
This parameter indicates the interval between two cell paging group packets, which is an integral multiple of 50 ms.
The cell paging message packaging is determined by the system load. If the paging message packaging timer is enabled, the paging
messages are packaged according to cells; otherwise, the paging messages are packaged according to the MTLS.
This parameter indicates the algorithm type of the interference band measurement when frequency scan is enabled: interference
band algorithm I or interference band algorithm II.
This parameter indicates the algorithm type of the interference band measurement when frequency scan is enabled: interference
band algorithm I or interference band algorithm II.
This parameter indicates when BTSs are cascaded, whether the BSC allows the CS service to preempt the sublink resources of the
PS service of the lower-level BTS if the sublink of the BTS cannot be preempted.
This parameter indicates whether the BSC allows the CS service to preempt the sublink resources of the PS service.
This parameter indicates whether the BSC forces the MS to send the handover access message.
This parameter indicates whether the MS can be handed over to other channels through assignment procedure in intra-cell
handover.
Every UL frequency is scanned for 10 times. The average of the 10 levels is reported. The result type is main/diversity before, and
maximum/average is new added.
If this parameter is set to 0, the call drop caused by the expiration of the intra-cell handover is not measured as a call drop . If this
parameter is set to 1, the call drop caused by the expiration of the intra-cell handover is measured as a call drop.
If this parameter is set to 0, the call drop caused by the expiration of the intra-BSC out-cell handover is not measured as a call
drop . If this parameter is set to 1, the call drop caused by the expiration of the intra-BSC out-cell handover is measured as a call
drop.
If this parameter is set to 0, the call drop caused by the expiration of the out-BSC handover is not measured as a call drop . If this
parameter is set to 1, the call drop caused by the expiration of the out-BSC handover is measured as a call drop.
If this parameter is set to 0, the call drop caused by the expiration of the into-BSC handover is not measured as a call drop . If this
parameter is set to 1, the call drop caused by the expiration of the into-BSC handover is measured as a call drop.
If this parameter is set to 0, the call drop caused by the resource check is not measured as a call drop . If this parameter is set to 1,
the call drop caused by the resource check is measured as a call drop.
this parameter is set to 0, the call drop caused by the unavailability of measurement reports on the MS for a long time is not
measured as a call drop . If this parameter is set to 1, the call drop caused by the unavailability of measurement reports on the MS
for a long time is measured as a call drop.
If this parameter is set to 0, the call drop caused by the forced handover failure is not measured as a call drop . If this parameter is
set to 1, the call drop caused by the forced handover failure is measured as a call drop.
If this parameter is set to 0, the call drop caused by the Abis territorial link failure is not measured as a call drop . If this parameter
is set to 1, the call drop caused by the Abis territorial link failure is measured as a call drop.
If this parameter is set to 0, the call drop caused by the Abis territorial link failure is not measured as a call drop. If this parameter
is set to 1, the call drop caused by the Abis territorial link failure is measured as a call drop.
If this parameter is set to 0, the call drop caused by either of the following factors is not measured as a call drop,If this parameter
If this parameterisisset
settoto0,0,the call
the drop
call caused
drop by by
caused either of reasons
other the following factors isfailure
of connection not measured
(besidesas a call
the drop: four connection
previous
failures) is not measured as a call drop . If this parameter is set to 1, the call drop caused by other reasons of connection failure
(besides the previous four connection failures) is measured as a call drop.
If this parameter is set to 0, the call drop caused by the unavailability of radio resources is not measured as a call drop . If this
parameter is set to 1, the call drop caused by the unavailability of radio resources is measured as a call drop.
If this parameter is set to 0, the call drop caused by the OM intervention is not measured as a call drop . If this parameter is set to
1, the call drop caused by the OM intervention is measured as a call drop.
If this parameter is set to 0, the call drop caused by the HO access failure is not measured as a call drop . If this parameter is set to
1, the call drop caused by the HO access failure is measured as a call drop.
If this parameter is set to 0, the call drop caused by the radio link failure is not measured as a call drop. If this parameter is set to
1, the call drop caused by the radio link failure is measured as a call drop.
If this parameter is set to 0, the call drop caused by the radio link failure is not measured as a call drop . If this parameter is set to
1, the call drop caused by the radio link failure is measured as a call drop.
If this parameter is set to 0, the call drop caused by the error of unsolicited DM response is not measured as a call drop . If this
parameter is set to 1, the call drop caused by the error of unsolicited DM response is measured as a call drop.
If this parameter is set to 0, the call drop caused by the T200 timeout is not measured as a call drop . If this parameter is set to 1,
the call drop caused by the T200 timeout is measured as a call drop.
To indicate whether a repeater is present. This parameter influence the handover between the repeaters. For repeaters that are
far away from each other should have asynchronous handovers, otherwise handovers will be failed.
To indicates the delay time after the cell initialization to detect whether the TRX mutual-aid function is enabled. To delay
detecting whether the trx mutual aid function is enabled because the cell that has been initialized is not in the stable state.
To indicate whether the flow on Abis interface is allowed. When BSS is congested some requests are rejected or delayed to
decrease the system load. This function applies to call management.
To indicate whether half rate is supported in the cell or not. It is one of the cell re-selection parameters in system message 3.
This parameter indicates the maximum transmit power level of MSs. It is one of the cell re-selection parameters in system
message 3.
This parameter indicates whether the power control function is allowed. It is one of the cell selection parameters in system
message 3.
---
To indicate the interval between the transmission of an overload message and the retransmission of the overload message from
the BTS to the BSC
TO indicate the load on CCCH timeslot. Overload message is sent to the BSC by BTS if the load on CCCH is greater than this
threshold.
To indicates the interval between the transmission of a load message and the retransmission of the load message. Used by BTS to
inform the BSC about the load on the CCCH timeslot.
Used by BTS to inform the BSC of the interference levels on the idle channels of a TRX. This parameter indicates the period of
sendingadjustment.
This parameter indicates the value of frequency the RF Resource indicationconsists
The parameter message.of 16 bits. The most significant bit indicates
whether the parameter is valid. Bits 14-8 indicate the level threshold. Bits 7-0 indicate the BER threshold.
If this parameter is set to Yes, the BTS calculates the speed of the MS with the BTS as the reference object and reports the speed
in the uplink measurement report to the BSC. The value Yes is used for deciding whether to initiate quick cell switchover.
This parameter is used to detect whether the antenna feeder system connecting the TRX is faulty. Smaller the value, smaller will
be the error and vice versa.
This parameter is used to detect whether the antenna feeder system connecting the TRX is faulty. Smaller the value, smaller will
be the error and vice versa.
Indicates the threshold of the error and triggering condition for the generation of alarm. If the output power of a trx of a
transmitter is lower than a fixed value, an error is generated. Greater the value, smaller the error and vice versa.
Indicates the threshold of the error and triggering condition for the generation of alarm. If the output power of a trx of a
transmitter is lower than a fixed value, an error is generated. Greater the value, smaller the error and vice versa.
This parameter is used for BTS 2X to compensate the difference between the RSSI when the TMA is installed and the RSSI when
the TMA is not installed and to ensure the accuracy of the RSSI value when BTS 2X has no TMA. For other BTS version, this
parameter is not used.
To indicate the start frame number of the BTS. To Keep synchronization between MS and BTS after BTS is re-initialized.
This parameter indicates the maximum number of levels that the BTS RF power decreases. It controls the reduction in the BTS RF
power . Higher this value, lower will be BTS RF power and vice versa.
Before the BTS transmits the radio resource indication message to the BSC, the interference levels measured on idle channels in
the period defined by this parameter are averaged.
This parameter indicates the threshold used for the interference measurement. The BSS measures the uplink quality of the radio
channels occupied by the serving MSs, calculates, and reports the interference level for each of the idle channels. This helps the
BSC to assign channels. The measurement result of the interference bands helps to set variable thresholds and analyze the
interference.
This parameter indicates the threshold used for the interference measurement. The BSS measures the uplink quality of the radio
channels occupied by the serving MSs, calculates, and reports the interference level for each of the idle channels. This helps the
BSC to assign channels. The measurement result of the interference bands helps to set variable thresholds and analyze the
interference.
This parameter indicates the threshold used for the interference measurement. The BSS measures the uplink quality of the radio
channels occupied by the serving MSs, calculates, and reports the interference level for each of the idle channels. This helps the
BSC to assign channels. The measurement result of the interference bands helps to set variable thresholds and analyze the
interference.
This parameter indicates the threshold used for the interference measurement. The BSS measures the uplink quality of the radio
channels occupied by the serving MSs, calculates, and reports the interference level for each of the idle channels. This helps the
BSC to assign channels. The measurement result of the interference bands helps to set variable thresholds and analyze the
interference.
This parameter indicates the threshold used for the interference measurement. The BSS measures the uplink quality of the radio
channels occupied by the serving MSs, calculates, and reports the interference level for each of the idle channels. This helps the
BSC to assign channels. The measurement result of the interference bands helps to set variable thresholds and analyze the
interference.
This parameter indicates the threshold used for the interference measurement. The BSS measures the uplink quality of the radio
channels occupied by the serving MSs, calculates, and reports the interference level for each of the idle channels. This helps the
BSC to assign channels. The measurement result of the interference bands helps to set variable thresholds and analyze the
interference.
If the parameter Assignment Cell Load Judge Enabled is set to Yes, the direct retry process is started and channels are assigned
when the cell supports direct retry and the load of the current cell is equal to or greater than the value of Cell Direct Try
Forbidden Threshold during channel assignment.
Short message of cell broadcast DRX mode. Here, DRX means SMSBC DRX MODE (cell broadcast short message incontinuous
receiving mode). BSC supporting SMSBC DRX must send scheduling message for MS to receive cell broadcast messages
incontinuously. A scheduled message includes many broadcast messages to be sent in a cell. The duration occupied by the
broadcast messages in scheduled message is called scheduled period. The scheduled message includes both the description of
short messages (arranged in the order of transmission sequence) to be broadcasted and their respective positions in the
scheduled period. Therefore, MS can fetch the wanted broadcast message in the least time, and the power consumption is also
Indicates the types of data services supported. This parameter is set according to the requirements
If this parameter is set to StartUp, the BSC sends the handoff command to the MS and adjusts the transmission power of the BTS
to the maximum.
This parameter During the
controls whether the BTS
handoff, thethe
reports BSCvoice
doesquality
not change
indexthe BTSVoice
(VQI). powerquality
to ensure the handoff
becomes success.
better as the voice level
decreases.
In the BTS3002C, the signals transmitted through the primary and secondary antennas are optimized by the low noise amplifier
(LNA ) bypass circuit. The BTS3002C supports the configuration of diversity antennas. That is, the main diversity signals
transmitted on a DRU are treated by the LNA circuit and then connected to the diversity port of another DRU through a tributary.
When both the MS and the network support PFC, the QoS parameters are obtained from the ABQP in the PFC.
Default MCS type used on the downlink.
MCS type fixedly used on the downlink.
Default MCS type used on the uplink.
MCS type fixedly used on the uplink.
Average period of bit error probe.
During the data transmission process, the modulation scheme and coding scheme can be changed to dynamically adapt to the radio transmission
Retransmissionenvironment,
rate thresholdthus improving
for the theTBF
downlink quality of links.
to change from CS4 to CS3.
Retransmission rate threshold for the downlink TBF to change from CS3 to CS2.
Retransmission rate threshold for the downlink TBF to change from CS2 to CS1.
Retransmission rate threshold for the downlink TBF to change from CS3 to CS4.
Retransmission rate threshold for the downlink TBF to change from CS2 to CS3.
Retransmission rate threshold for the downlink TBF to change from CS1 to CS2.
Default CS type used on the downlink.
CS type fixedly used on the downlink.
Retransmission rate threshold for the uplink TBF to change from CS4 to CS3. When the retransmission rate of the uplink TBF is greater than or
equal to the value of this parameter, the coding scheme of the uplink TBF changes from CS4 to CS3.
Retransmission rate threshold for the uplink TBF to change from CS3 to CS2.
Retransmission rate threshold for the uplink TBF to change from CS2 to CS1.
Retransmission rate threshold for the uplink TBF to change from CS3 to CS4. When the retransmission rate of the uplink TBF is smaller than or
equal to the value of this parameter, the coding scheme of the uplink TBF changes from CS3 to CS4.
Retransmission rate threshold for the uplink TBF to change from CS2 to CS3.
Retransmission rate threshold for the uplink TBF to change from CS1 to CS2.
Default CS type used on the uplink.
CS type fixedly used on the uplink.
Timer set to release the Abis timeslots.
Number of channels reserved for CS services.
Level of dynamic channel preemption by CS services and PS services
Timer set to release the idle dynamic channel.
In a concentric cell, the overlaid subcell uses DCS1800 and the underlaid subcell uses GSM900.
PDCH downlink multiplex threshold
PDCH uplink multiplex threshold.
Downlink multiplex threshold of dynamic channel conversion.
Uplink multiplex threshold of dynamic channel conversion.
The total number of TCHs and PDCHs is fixed. The PDCH ratio equals PDCHs/(TCHs + PDCHs).
Multi-frequency reporting.
Threshold of HCS signal strength.
HCS priority of a GPRS cell.
Maximum TX power level for an MS to access the packet control channel.
Minimum RX power level for an MS in the cell to access the system.
Exclusive access or not.
Whether the cell can be accessed during cell reselection.
Hysteresis of cell reselection in different routing areas.
Period when cell reselection is prohibited.
Whether the MS can access another cell.
Whether GPRS_RESELECT_OFFSET is used for C32 calculation during cell reselection Value range: 0, 1.
Whether GPRS Cell Reselect Hysteresis is applied to the C31 standards.
Hysteresis of cell reselection in the same routing area.
Whether the PSI status message is supported.
Whether the measurement report command is allowed.
Repetition period of the PS information PSI1.
Persistence level 4 of radio priority access.
Persistence level 3 of radio priority access.
Persistence level 2 of radio priority access.
Persistence level 1 of radio priority access.
Number of timeslots for extension transmission in random access.
Minimum number of timeslots between two successive channel requests.
Maximum number of retransmissions for radio priority 4.
Maximum number of retransmissions for radio priority 3.
Maximum number of retransmissions for radio priority 2.
Maximum number of retransmissions for radio priority 1.
Access control class; 16-bit bitmap; value range: 0-65535.
Number of PRACH blocks. Value range: 1-12.
Number of PAGCH blocks. Value range: 1-12.
Number of PBCCH blocks. Value range: 1-4.
Period of cell reselection measurement report in packet transfer mode.
Period of cell reselection measurement report in packet idle mode.
Minimum duration when the MS stays in non-DRX mode after the NC-measurement report is sent.
GPRS reselection offset is used to calculate C32. A higher value indicates a higher access priority.
Timer used for the MS to calculate C32. The timer is sent through the system information broadcast in each cell.
When the BCCH frequency of a cell is listed in the neighbor cells for the MS, the negative offset of C2 is calculated before timer T expires.
Interval between extension measurement reports.
Frequency type in the extension measurement report. Value range: type1, type2, and type3
Frequency index of the interference measurement. Value range: 0-31.
Whether MSs are permitted to report the NCC bitmap of measurement reports. 0-255 are the parameters of the NCC bitmap.
The network can require the MS to send measurement reports. When the MS is in idle mode, it sends the extension measurement reports. This
parameter can be set to em0 or em1.
Whether the CS paging on the A interface is supported.
Whether the 11-bit EGPRS access is supported.
Routing area color code of a GPRS cell.
This parameter determines the priority of packet access of MSs to a cell.
Whether the cell supports SPLIT_PG_CYCLE on the CCCH.
In the cell reselection required by the network, the network requests the MS to send measurement reports to control its cell reselection. There
are three
Pan Max.is network
also the control
maximum modes.
value of N3102.
This parameter is used to set the value of N3102. When the MS receives a Packet Uplink Ack/Nack message that allows V(S) or V(A) increase,
N3102
This parameter is used to set the value is increased
of N3102. Whenby the value
T3182 of this
expires, parameter.
N3102 is decreased by the value of this parameter.
Maximum countdown value of the MS
Control acknowledgment type. This parameter determines the acknowledgment message type used by the MS.
Access burst type used by the MS in the PRACH, PTCCH/U, and packet control acknowledgment message.
Maximum duration of the non-DRX mode. DRX_Timer_Max (DRX: discontinuous reception) is a parameter carried by the cell broadcast message.
Timer set for the MS to wait for the TBF release after receiving the last data block.
Timer set for the MS to wait for the Packet Uplink Assignment message.
Based on the paging channel used by the system, the network operation modes are classified into Network Operation Mode I, Network Operation
Mode II, is
This parameter and Network
used for theOperation
open loopMode
powerIII.control.
Initial power level.
Signal strength filter length in packet idle mode.
Signal strength filter length in packet transmission mode.
This parameter determines the channel where the receive power level of the MS is measured for the uplink power control.
Constant of the interference signal strength filtering by power control.