Documente Academic
Documente Profesional
Documente Cultură
Getting Started
2. All electrical and electronic products European Standards Centre:
should be disposed of separately Krijgsman 1, 1186 DM Amstelveen
from the municipal waste stream The Netherlands
via designated collection facilities
appointed by the government or the yy Please note that this is NOT a
local authorities. Customer Service contact point. For
Customer Service Information, see
3. The correct disposal of your old
Warranty Card or contact the dealer
appliance will help prevent potential
that you purchased this product.
negative consequences for the
environment and human health.
4. For more detailed information about
disposal of your old appliance, please POWER: This unit operates on a mains supply of
contact your city office, waste disposal 200-240V~, 50/60Hz.
service or the shop where you WIRING: This unit is supplied with a BSI 1363
purchased the product. approved 13 amp mains plug, fused at 5 amp.
Disposal of waste batteries/accumulators When replacing the fuse always use a 5 amp BS
1362, BSI or ASTA approved type. Never use this
plug with the fuse cover omitted. To obtain a
1. When this crossed-out wheeled replacement fuse cover contact your dealer. If the
bin symbol is attached to batteries/ type of plug supplied is not suitable for the mains
accumulators of Your product it means sockets in your home, then the plug should be
they are covered by European Directive removed and a suitable type fitted. Please refer to
2006/66/EC. the wiring instructions below:
2. This symbol may be combined with
WIRING: A mains plug removed from the mains
chemical symbols for mercury(Hg),
lead of this unit must be destroyed. A mains plug
cadmium(Cd) or lead(Pb) if the battery
with bared wires is hazardous if inserted in a
Contains more that 0.0005% of
mains socket. Do not connect either wire to the
mercury,0.002% of cadmium or 0.004%
earth pin, marked with the letter E or with the
of lead.
earth symbol or coloured green or green and
3. All batteries/accumulators should be yellow. If any other plug is fitted, use a 5 amp fuse,
disposed separately from the municipal either in the plug, or at the distribution board.
waste stream via designated collection
facilities appointed by the government IMPORTANT: The wires in this mains lead are
or the local authorities. coloured in accordance with the following codes:
4. The correct disposal of Your old - BLUE: NEUTRAL, BROWN: LIVE - As the colours
batteries/accumulators will help of the wires in the mains lead of this unit may not
to prevent potential negative correspond with the coloured marking identifying
consequences for the environment, the terminals in your plug, proceed as follows: The
animal and human health. wire which is coloured blue must be connected
5. For more detailed information to the terminal which is marked with the letter
about disposal of Your old batteries/ N or coloured black. The wire which is coloured
accumulators, please contact Your city brown must be connected to the terminal which
office, waste disposal service or the is marked with the letter L or coloured red.
shop where You purchased the product.
1
5 Troubleshooting
27 Troubleshooting
6 Appendix 2
28 Maintenance
28 Handling the Unit
28 Notes on Discs
29 Area Code List 3
30 Language Code List
31 Trademarks and Licenses
32 Specifications
7 Warranty 4
34 Warranty
Getting Started
contains audio titles, DivX, MP3, WMA and/or
JPEG files. Some DVDRW/DVDR or CD-RW/ y Video files contained in the
USB/Disc
CD-R cannot be played on this unit due to the
recording quality or physical condition of the disc, u Audio files contained in the
or the characteristics of the recording device and USB/Disc
authoring software.
i Photo files
DVD-VIDEO (8 cm / 12 cm disc)
Discs such as movies that can be
purchased or rented. ,,Note
Indicates special notes and operating features.
DVDR (8 cm / 12 cm disc)
Video mode and finalized only. >>Caution
DVD-RW (8 cm / 12 cm disc) Indicates cautions for preventing possible damages
from abuse.
Video mode and finalized only.
DVD VR format that have been
finalized can not be played in this Regional Codes
unit. This unit has a regional code printed on the rear of
DVD+R: Video mode only. the unit. This unit can play only DVD discs labeled
same as the rear of the unit or ALL.
Supports the double layer disc also.
yy M
ost DVD discs have a globe with one or more
DVD+RW (8 cm / 12 cm disc) numbers in it clearly visible on the cover. This
Video mode and finalized only. number must match your units regional code; or
the disc cannot play.
Audio CD: Music CDs or CD-R/CD-
yy I f you try to play a DVD with a different regional
RW in music CD format that can be code from your unit, the message Check
purchased. Regional Code appears on the TV screen.
Getting Started
yy T he file name of the DivX subtitle should be
entered within 45 characters.
yy I f there is impossible code to express in the
DivX file, it may be displayed as _ mark on the
display.
yy F rame rate : less than 30 fps.
yy I f the video and audio structure of recorded
files is not interleaved, either video or audio is
outputted.
yy P
layable DivX file : .avi, .mpg, .mpeg, .divx
yy P
layable Subtitle format : SubRip (*.srt/ *.txt),
SAMI (*.smi), SubStation Alpha (*.ssa/ *.txt),
MicroDVD (*.sub/ *.txt), SubViewer 2.0 (*.sub/
*.txt), Vobsub (*.sub)
yy P
layable Codec format : DIVX3.xx, DIVX4.xx,
DIVX5.xx, MP4V3, 3IVX.
yy P
layable Audio format : AC3, PCM, MP3, WMA.
yy S ampling frequency : within 32 to 48 kHz (MP3),
within 32 to 48 kHz (WMA)
yy B
it rate : within 32 kbps to 320 kbps (MP3), 40
kbps to 192 kbps (WMA)
yy F or Discs formatted in Live file system, you can
not it on this unit.
yy I f the name of movie file is different from that of
the subtitle file, during playback of a DivX file,
subtitle may not be display.
yy I f you play a DivX file different from the DivXspec,
it may not operate normally.
Front panel
1 2 3 4 5 6 7
1
Getting Started
11 10 9 8
a DVD/CD Disc Drawer h TUNING (-/+)(C/V), Skip/Search
b Power (1/!) You can search chapter/ track/ file by pressing
and holding C/V.
c Open/Close (B)
i USB port
d Display window You can play video, image and sound files by
e Play/Pause (d/M), MONO/ ST. connecting the USB device.
f Stop (Z) jP
.(Portable) IN port
g Function (F) You can enjoy music from portable device on
Selects the function or input source. your unit.
k Volume (VOL.)
Rear panel
1 2 3 4 5 6
7
a Power cord e MONITOR (VIDEO OUT) connector
b Speaker terminal Connect to a TV with video inputs.
c ANTENNA connector (FM) f AUX (L/ R) INPUT connector
d SCART connector g COMPONENT VIDEO (PROGRESSIVE SCAN)
OUTPUT (Y PB PR)
Connect to a TV with Y PB PR inputs.
Remote control
POWER : Switches the unit ON or VOL (Volume) (+/-) : Adjusts
1 OFF. speaker volume. 1
OPEN/CLOSE : Opens and closes LG EQ (9) : Selects a NAT PLUS
Getting Started
the disc Drawer. or Local Specialization equalizer
TITLE : If the current DVD title has effect by using LG EQ.
2 a menu, the title menu appears EQ$ (EQUALIZER effect) :
on the screen. Otherwise, the disc Chooses sound impressions.
menu may not appear. CLEAR : Removes a track number
b on the Program List.
DISPLAY : Accesses On-Screen SUBTITLE : During playback, press
3
Display. SUBTITLE repeatedly to select a
desired subtitle language .
MENU : Accesses the menu on a
DVD disc. 0 to 9 numerical buttons :
Selects numbered options in a
4 SETUP : Accesses or removes menu.
setup menu.
PRESET (WS) : Selects e
programme of Radio. TV Control buttons : Controls the
TUN. (-/+) : Tunes in the desired TV. (LG TV only)
5 radio station. -- You can control the sound
W/S/A/D (up/ down/ left/ level, input source, and power
right): Used to navigate on-screen switching of LG TVs as well.
displays. Hold POWER (TV) and press
PR/CH (+/) button repeatedly
ENTER (b) : Acknowledges menu until the TV turns on or off.
selection.
PROG./MEMO. : Accesses or
Battery Installation RETURN (x) : Moves backwards removes Program menu.
in the menu or exits the setup
menu. ?: This button is not available.
REC (X) : USB Direct Recording. RDS : Radio Data System.
PTY : Views the various displays of
c the RDS.
STOP (Z) : Stops playback or
recording.
Remove the battery cover on the PLAY (d), MO./ST. : Starts
rear of the Remote Control, and playback. Selects Mono/ Stereo.
insert one (size AAA) battery with PAUSE/STEP (M) : Pauses
4 and 5 matched correctly. playback.
SKIP (C/V) : Goes to next
or previous chapter/ track/ file.
a
SCAN (c/v) : Searches
FUNCTION : Selects the function
backward or forward.
and input source.
SLEEP : Sets the system to turn off d
automatically at a specified time. REPEAT/RANDOM : Selects a play
(Dimmer : The display window will mode.(Random, repeat)
be darken by half.) MUTE : Mutes the sound.
PC monitor. A A
A
E
A
A
D
Connecting
in this manual.
yy Please refer to the manuals of your TV,
Stereo System or other devices as necessary
to make the best connections.
>>Caution
yy Make sure the unit is connected directly
to the TV. Tune the TV to the correct video
input channel
yy Do not connect your player via your VCR.
The image could be distorted by the copy
protection system.
,,Note
If your TV accepts progressive format signals,
you must use this connection and set
[Progressive Scan] in [Display] setup to [On]
(See page 17).
SCART Connection
Connect the SCART jack on the unit to the SCART in
jack on the TV using a video cable.
You can hear the sound through the systems
speakers.
Connecting
Removing the USB Device from the unit
1. Choose a different function mode or
press STOP (Z) twice in a row. ,,Note
2. Remove the USB device from the unit. Be sure to fully extend the FM wire antenna.
After connecting the FM wire antenna, keep it
as horizontal as possible.
LANGUAGE
2. Use WSAD to select a language then press
ENTER.
Menu Language
The confirm menu will appear. Select a language for the Setup menu and then on
screen display.
TV Output Select
[Original]
Select an option according to the TV connection
Refers to the original language in which the type.
disc was recorded.
[Other] [RGB]
To select another language, press numeric When your TV is connected with the SCART
buttons and then ENTER to enter the jack.
corresponding 4-digit number according to
the language code list on the page 30. If you [YPBPR]
enter the wrong language code, press CLEAR. When your TV is connected with the
COMPONENT/ PROGRESSIVE SCAN jacks on the
[Off (for Disc Subtitle)] unit.
Turn off Subtitle.
,,Note
DISPLAY If you change TV Output Select to RGB from
3
YPbPr on the setup menu especially when
connecting the unit in the way of component
System Setting
TV Aspect video connection, the screen turns black.
Select which screen aspect to use based on the In that case, connect the video cable to
shape of your TV screen. MONITOR jack and select YPbPr on the setup
menu again.
[4:3]
Select when a standard 4:3 TV is connected. Progressive Scan (For Component
[16:9]
Video connections)
Select when a 16:9 wide TV is connected. Selects whether the COMPONENT
VIDEO(PROGRESSIVE SCAN) OUTPUT jacks output
progressive signal. If your TV accepts progressive
Display Mode format signals, you will enjoy accurate color
The Display Mode setting works only when the TV reproduction and high quality image by selecting
Aspect mode is set to 4:3. [On]. If your TV does not accept progressive format
signals, select [Off ].
[Letterbox] If you set Progressive Scan to [On] in error, you must
reset the unit. First, remove the disc in the unit.
Displays a wide picture with bands on the
Next, press and hold STOP (Z) for five seconds.
upper and lower portions of the screen.
The video output will be restored to the standard
[Panscan] setting, and a picture will be visible on your TV.
Automatically displays the wide picture on the
entire screen and cuts off the portions that do
not fit. (If the disc/file is not compatible with
Pan Scan, the picture is displayed at Letterbox
ratio.)
AUDIO [Volume]
Press AD to adjust the output level of the
DRC (Dynamic Range Control) selected speaker.
Make the sound clear when the volume is turned [Distance]
down (Dolby Digital only). Set to [On] for this effect.
After you connected speakers to your unit,
set the Distance between the speakers and
Vocal your listening point if the distance of Center
Select [On] to mix karaoke channels into normal or Rear speakers is bigger than the distance
stereo. of Front speakers. This allows the sound from
each speaker to reach the listener at the same
This function is effective for multi-channel karaoke
time. Press AD to adjust the Distance of the
DVDs only.
selected speaker. This distance is equivalent to
a difference of the distance between Center or
5.1 Speaker Setup Rear speaker and Front speakers.
3 Make the following settings for the built-in 5.1 [Test]
channel surrounds decoder.
System Setting
[Size]
Since the speaker settings are fixed, you cannot
change the settings.
System Setting
4. Press ENTER to confirm your rating selection. DivX(R) VOD
ABOUT DIVX VIDEO: DivX is a digital video
Password format created by DivX, LLC, a subsidiary of Rovi
You can enter or change password. Corporation. This is an official DivX Certified device
that plays DivX video. Visit divx.com for more
1. Select [Password] on the [Lock] menu and then information and software tools to convert your files
press D. into DivX videos.
2. Input a password and press ENTER. ABOUT DIVX VIDEO-ON-DEMAND: This DivX
To change the password, press ENTER when Certified device must be registered in order to play
the [Change] option is highlighted. Input a purchased DivX Video-on-Demand (VOD) movies.
password and press ENTER. Enter it again and To obtain your registration code, locate the DivX
press ENTER to verify. VOD section in your device setup menu. Go to vod.
3. Press SETUP to exit the menu. divx.com for more information on how to complete
your registration.
,,Note
If you forget your password, you can clear [Register]
it using the following steps:
Displays the registration code of your unit.
1. Press SETUP to display the Setup menu.
2. Input the 6-digit number 210499 and [Deregister]
press ENTER. The password is cleared. Deactivate your unit and display the deactivation
code.
,,Note
All the downloaded videos from DivX VOD
can only be played back on this unit.
20 Operating
Operating
Angle Selected angle/total number of angles.
Sound Selected sound mode. Selecting a subtitle language
,,Note ry
If any button is not pressed for a few seconds, During playback, press SUBTITLE( ] ) repeatedly
the onscreen display disappears. to select a desired subtitle language.
Operating
1. Use WSAD to highlight (
press ENTER to start slide Show.
) icon then
,,Note
You can check the remaining time before the
2. You can change slide show speed using unit turns off.
AD when ( ) icon is highlighted.
About help menu for slide show
Dimmer
Menu Buttons Operation
Press SLEEP once. The display window will be
w/s Rotating the darken by half. To cancel it, press SLEEP repeatedly
W/S picture until dimmer gets off.
/
a/ d Moving to
Prev./ Next
A/D
another file Turn off the sound temporarily
Press MUTE to mute your unit.
x Hiding the help
RETURN menu You can mute your unit, for example, to answer
Hide
the telephone, the MUTE displayed in the display
Closing the slide window.
Z STOP show
On Display Description
You can enjoy the natural
NAT PLUS sound effect same as a
5.1-channel.
Operating
equalizer MERENGUE/ SALSA/ SAMBA/
CUMBIA/ AFRO) (Optional)
4. Turn the portable player or external device and The making of unauthorized copies of copy-
start it playing. protected material, including computer programs,
files, broadcasts and sound recordings, may be
an infringement of copyrights and constitute a
Recording to USB criminal offense. This equipment should not be
1. Connect the USB device to the unit. used for such purposes.
2. Select a DVD/ CD function by pressing Be responsible
FUNCTION. Respect copyrights
One track recording - You can record to USB after
playing the file you want.
All tracks recording - You can record to USB after
stop.
Program list recording - After showing the
programmed list, you can record it to USB.
3. Start the recording by pressing X REC.
4. To stop recording, press Z STOP.
Troubleshooting
PROBLEM CORRECTION
No power Plug the power cord into the wall outlet securely.
Select the appropriate video input mode on the TV so the picture
from the unit appears on the TV screen.
No picture
Connect the video cables securely to both the TV and unit.
Select the correct input mode of the unit so you can hear the sound
from the unit.
There is little or no sound Connect the audio cables into the connection terminals correctly.
Replace with a new audio cable.
The DVD picture quality is poor Clean the disc using a soft cloth with outward strokes.
Insert a disc.
Insert a playable disc (check the disc type, colour system and
regional code).
A DVD/CD will not play
Place the disc with the label or printed side facing upwards.
Enter your password or change the rating level.
Troubleshooting
Check the antenna connection and adjust its position.
Attach an external aerial if necessary.
Radio stations cant be tuned in
properly. Tune to the station manually.
Preset some radio stations, see page 24 for details.
The remote is not pointed directly at the unit.
Point the remote directly at the unit.
The remote is too far from the unit.
Use the remote within 23 feet (7m) of the unit.
The remote control doesnt work
well / at all There is an obstacle in the path between the remote control and
the unit.
Remove the obstacle.
The battery in the remote control are flat.
Replace the battery with new ones.
Appendix
Appendix
Specifications
General
Power requirements 200 - 240 V , 50/ 60 Hz
Power consumption 45 W
Dimensions (W x H x D) Approx. 360 x 65 x 320 mm without foot
Net Weight (Approx.) 2.5 kg
Operating temperature 5 C to 35 C (41 F to 95 F)
Operating humidity 5 % to 90 %
Outputs
VIDEO OUT 1.0 V (p-p), 75 , sync negative, RCA jack x 1
(Y) 1.0 V (p-p), 75 , sync negative, RCA jack x 1
COMPONENT VIDEO OUT
(Pb)/(Pr) 0.7 V (p-p), 75 , RCA jack x 2
ANALOG AUDIO IN 2.0 Vrms (1 kHz, 0 dB), 600 , RCA jack (L, R) x 1
PORT. IN 0.5Vrms (3.5 mm stereo jack)
System
Laser Semiconductor laser, wavelength: 650 nm
Signal system Standard NTSC/ PAL color TV system
Frequency response 20 Hz to 20 kHz (48 kHz, 96 kHz, 192 kHz sampling)
Signal-to-noise ratio More than 80 dB
Harmonic distortion 0.05 % at 1 W
Amplificador
Stereo mode 45 W + 45 W (4 at 1 kHz)
Front 45 W + 45 W (THD 1 %)
Center 45 W
Surround mode
Surround 45 W + 45 W (4 at 1 kHz)
Subwoofer 75 W (8 at 60 Hz)
Tuner
FM Tuning Range 87.5 to 108.0 MHz or 87.50 to 108.00 MHz
Front Speaker
Type 1 Way 1 Speaker
Impedance Rated 4
Input Power 45 W
Max. Input Power 90 W
Net Dimensions (W x H x D) 103 x 111 x 94 mm
Net Weight 0.39 kg
Rear Speaker
Type 1 Way 1 Speaker
Impedance Rated 4
Input Power 45 W
Max. Input Power 90 W
Net Dimensions (W x H x D) 103 x 111 x 94 mm
Net Weight 0.39 kg
Centre Speaker
Type 1 Way 1 Speaker
Impedance Rated 4
Input Power 45 W
Max. Input Power 90 W
Net Dimensions (W x H x D) 103 x 111 x 94 mm
Net Weight 0.39 kg
Subwoofer
6
Appendix
Type 1 Way 1 Speaker
Impedance Rated 8
Input Power 75 W
Max. Input Power 150 W
Net Dimensions (W x H x D) 156 x 325 x 320 mm
Net Weight 3.6 kg
In all cases of difficulty - consult your LG dealer from whom the product was purchased