Documente Academic
Documente Profesional
Documente Cultură
Radan 2018 R1
Installation Guide
Contents
1 Radan CAD/CAM 2018 R1 and Radbend 2018 R1 .................. 3
1.1 Introduction
The installation instructions will guide you through installing or updating to Radan CAD/CAM 2018
R1 and Radbend 2018 R1.
Important information
Radan licensing is based around Sentinel RMS, which either uses some of your computer’s hardware
or a CLS Token (dongle) to identify the PC which manages the Radan Licenses. This means that any
changes to your hardware or a change to a new server will mean that you may need to transfer the
license. Always contact support beforehand to discuss.
CAD/CAM
Pentium 4, 2 GHz CPU or greater
4GB RAM or greater (depending on OS)
20 GB available storage
Graphics card capable of 1024 x 768 minimum resolution (32bit mode)
DVD ROM drive
Available RS232 Serial ports (one port per machine requiring RS232 serial DNC)
Keyboard and mouse
Network interface using TCP/IP
Note: This PC specification also applies when configured as a PC DNC, Radview DNC client computer.
CAD/CAM with 3D / Radbend / RadviewPlus Server / RadviewDNC Server
Dual Core, 2.8 GHz CPU or greater
8GB RAM or greater (depending on OS)
40 GB available storage
Dedicated graphics card capable of 1024 x 768 minimum resolution (32bit mode)
DVD ROM drive
Available RS232 Serial ports (one port per machine requiring RS232 serial DNC)
Keyboard and mouse
Network interface using TCP/IP
Supported Operating systems
Windows® 7, Windows® 8, Windows® 10 (see Important Note below)
Windows Server 2008 R2, Windows® Server 2012
We may require the latest service packs to be installed
64bit versions are supportedProfessional / Business versions of the operating systems are
recommended
Important Note
Additional Notes
A Virtual Server will need a USB CLS Token (dongle) at an additional cost if it is to run as a
license server. Please be aware not all Virtualisations can support USB Tokens.
A USB port must be available if the PC is going to be licensed from a CLS Token (dongle).
Software and subsequent updates will be shipped on DVD ROM only; however they can be
downloaded from the Customer Portal.
If the customer purchases Radan's installation service, it is their responsibility to make sure
the IT structure/hardware is suitable based on system requirements above. The Radan
engineer will require any PC to have a supported Windows O/S, Administrative Rights and
network access (if using network applications) to be able to install and configure Radan
software.
Application performance is dependent upon a number of factors e.g. Number of used
applications or network traffic. Should you require further clarification, please contact your
IT provider.
CPU Processor must the support SSE2 instruction set, see http://en.wikipedia.org/wiki/SSE2
License file
The installation process will try to connect to our servers via the internet and automatically
download the license file. The licensing system uses a ‘lock code’ to identify your PC which will
become the Radan license server and is made up of your network card address and hard disk and is
unique to your PC.
If you have an internet connection on the PC you are installing the software on, this ‘lock code’ will
be sent to our server, together with details about your ‘Server Code’. Our server will then send back
the license file.
If you do not have an internet connection on the server you are installing the software on, you will
be asked to follow the manual procedure to obtain a license file. After the license file has been
downloaded or you have selected the license file in the installation screen, the RMS licensing
software will be installed and the Radan installation will continue.
Note: the lock code is generated from hardware components in the PC; this means that if you decide
to make any changes to the PC hardware, or intend to change the PC you use as the Radan License
Server, you will need to contact us.
2.1.2 Preparation
Before Installation please make sure you:
Reboot
Are logged in as a user with admin rights
Close all non-essential applications
Have a running Radan server that has started the software successfully
Reboot the Client PC
Are logged in as a user with admin rights
Close all non-essential applications
2.3.1 Preparation
Please make sure you:
You will also need to reboot the server after the update.
2.4.1 Preparation
Please make sure you:
Have upgraded the Radan server and started the software successfully
Boot up the client PC
You are logged in as a user with admin rights
Close all non-essential applications
The upgrade process will automatically detect that your PC is a Radan client and will update all
components automatically – please follow the on-screen instructions.
If you have an internet connection on the PC you are installing the software on, this ‘lock code’ will
be sent to our server, together with details about your ‘Server Code’. Our server will then send back
the license file.
If you do not have an internet connection on the server you are installing the software on, you will
be asked to follow the manual procedure to obtain a license file. After the license file has been
downloaded or you have selected the license file in the installation screen, the RMS licensing
software will be installed and the Radan installation will continue.
NB: the lock code is generated from hardware components in the PC; this means that if you decide
to make any changes to the PC hardware, or intend to change the PC you use as the Radan License
Server, you will need to contact us.
A System is an item that will ‘run’ by itself, such as the main Radan 2D CAD application) or DNC (PC-
DNC). There always needs to be one System license Reserved
A Module is an item that needs a running System to be able to be used, such as a nesting license, 3D
or a 3D translator. Module licenses can be Optional or Reserved
If the option ‘Use License Profiles’ is off then CLS will use the default profile that can apply to all
users.
On starting the software for the first time without a license profile set the ‘Configure Network
Licenses’ dialog will be loaded.
The ‘Configure Network Licenses’ dialog can also be accessed from Radan SystemInfo or via the
Radan 2018 R1 License Manager found in Start > Radan Software.
2.6.3 Systems
In the dialog select a System license and click « Reserved (the list on the left shows the licenses you
have selected for your license profile).
NB. Once you have Reserved a System license the list on the right may show additional Modules. You
can only select a Module after you have selected a System license that allows use of that Module.
2.6.4 Modules
You can add any Module to your license profile as either ‘Reserved’ or ‘Optional’.
Optional – any Modules that are Optional are not taken until you access the software that uses that
Module. E.g. in the license profile shown above, the 3D license Optional so will not be taken until
you enter 3D; up to that moment, any other user can take that license, possibly denying you that
license.
Important information
These instructions are displayed because the PC on which the software was installed does not have
Internet access. Please print or copy these instructions to another PC that has Internet access and
follow the steps below.
License download
Start your Internet Browser and go to:
https://customers.verosoftware.com/Public/Licensing/LicenceActivation.aspx
Enter the details; including an e-mail address if you wish to receive the license file by e-mail (this is
optional).
Press Generate License. This will show you the details of the license and a link to download the file.
Transfer the file to the server where you are performing the installation and select it during the
installation process.
Standalone
Server
Client
Smbviewer
Custom
Standalone
Standalone installation is used when licenses , “Data” and software is installed on the same PC .
Server
Server installation only installs the (RMS) license server and creates a “Data” folder that needs to be
shared manually. If you already have a license server installed (by the radan 2018 install) and have
already the “Data” folder on a network share you can skip the server installation.
Client
Client installation installs the software and will ask you after the installation what license server to
use and where the “Data” folder can be found.
Smbviewer
Smbviewer installation is a client installation for installing the viewer for simulating the bend
programs.
If you follow the instructions the wizard will try to connect to our servers via the internet and
automatically download the license file. The licensing system uses a ‘lock code’ to identify your PC
which will become the Radan license server and is made up of your network card address and hard
disk and is unique to your PC.
If you have an internet connection on the PC you are installing the software on, this ‘lock code’ will
be sent to our server, together with details about your ‘Server Code’. Our server will then send back
the license file.
If you do not have an internet connection on the server you are installing the software on, you will
be asked to follow the manual procedure to obtain a license file. After the license file has been
downloaded or you have selected the license file in the wizard the product is licensed.
License Profiles
Before you can start the software, you will need to specify which licenses you want to use. This is
called a license profile and it is specific to a user. A Radbend user needs at least BENDCAM and
probably CAD4CAM and specific translators.
Customer data
The customer “Data” is supplied in a zip file (*.zip or *tar.gz) and is revered to as “customer files”
during a server or standalone installation. You can however unzip this file to any folder manually and
select this folder the first time you start the software.
Two Radbend icons will be available, one to open the part directly into Radbend, the other to save a
JAX file.
3.5 Updates
Updates are usually detected automatically when running the Radbend setup. If the CLS license
server is already up to date by installing Radan 2018R1 there is no need to update Radbend on the
server.
Preparation
The upgrade process will automatically detect that your PC is a Radan client and will update all
components automatically – please follow the on-screen instructions.
Preparation
The upgrade process will automatically detect that your PC is a Radbend standalone and will update
all components automatically – please follow the on-screen instructions.
The update
The Radan 2018 R1 DVD you have received will install/update all necessary elements of the Radbend
software from any previous level.
Preparation
The upgrade process will automatically detect that your PC is a Radbend Server and will update all
components automatically – please follow the on-screen instructions.