Documente Academic
Documente Profesional
Documente Cultură
10040
PO Nº 1004006710
DOCUMENT TITLE:
PIPE DATA SHEET
CONTRACTOR review comments do not indicate either responsibility or liability for accuracy and completeness of this Document or alter any
contractual terms and conditions.
This document is property of UTE TR Fadhili Project and TR Saudia for Services and Contracting Co Ltd.
Its reproduction without previous permission in writing is strictly forbidden.
10040-00-082-PD-0002-tmp02
P I P E D A T A S H E E T S
Project 10040 ‐ Fadhili Gas Program (FGP)
Client UTE TR (Tecnicas Reunidas)
Service Oily Water & Sanitary Sewer (1FE0U01) ‐
Installation Type Burried ‐
System Thrust Balance Restrained ‐
Product Type GRE ‐
Manufacturing Process Helical Filament Winding ‐
Joint Type Adhesive Tapered Bell/Spigot ‐
Nominal Diameter 100 mm
Design Pressure 10.0 Barg
Site Hydrostatic Test Pressure 6.9 Barg
Required Vacuum Rating N/A Barg
Maximum Pipe Length 6,000 mm
Minimum Total Wall Thickness 3.2 mm
Liner Thickness 0.5 mm
Resin Type Epoxy ‐
Glass Type C‐Veil ‐
Structural Wall Thickness 2.4 mm
Resin Type Epoxy ‐
Glass Type E‐Glass ‐
Aggregate None ‐
Top Coat Thickness 0.3 mm
QUO‐LT‐041215‐15‐PDS R2 Form: TSD‐FCEN‐PDS‐R0
17/10/2016 16:10 Page: 1 of 21 Nov 25, 2012
P I P E D A T A S H E E T S
Project 10040 ‐ Fadhili Gas Program (FGP)
Client UTE TR (Tecnicas Reunidas)
Service Oily Water & Sanitary Sewer (1FE0U01) ‐
Installation Type Burried ‐
System Thrust Balance Restrained ‐
Product Type GRE ‐
Manufacturing Process Helical Filament Winding ‐
Joint Type Adhesive Tapered Bell/Spigot ‐
Nominal Diameter 150 mm
Design Pressure 10.0 Barg
Site Hydrostatic Test Pressure 6.9 Barg
Required Vacuum Rating N/A Barg
Maximum Pipe Length 12,000 mm
Minimum Total Wall Thickness 3.3 mm
Liner Thickness 0.5 mm
Resin Type Epoxy ‐
Glass Type C‐Veil ‐
Structural Wall Thickness 2.5 mm
Resin Type Epoxy ‐
Glass Type E‐Glass ‐
Aggregate None ‐
Top Coat Thickness 0.3 mm
QUO‐LT‐041215‐15‐PDS R2 Form: TSD‐FCEN‐PDS‐R0
17/10/2016 16:10 Page: 2 of 21 Nov 25, 2012
P I P E D A T A S H E E T S
Project 10040 ‐ Fadhili Gas Program (FGP)
Client UTE TR (Tecnicas Reunidas)
Service Oily Water & Sanitary Sewer (1FE0U01) ‐
Installation Type Burried ‐
System Thrust Balance Restrained ‐
Product Type GRE ‐
Manufacturing Process Helical Filament Winding ‐
Joint Type Adhesive Tapered Bell/Spigot ‐
Nominal Diameter 200 mm
Design Pressure 10.0 Barg
Site Hydrostatic Test Pressure 6.9 Barg
Required Vacuum Rating N/A Barg
Maximum Pipe Length 12,000 mm
Minimum Total Wall Thickness 4.1 mm
Liner Thickness 0.5 mm
Resin Type Epoxy ‐
Glass Type C‐Veil ‐
Structural Wall Thickness 3.3 mm
Resin Type Epoxy ‐
Glass Type E‐Glass ‐
Aggregate None ‐
Top Coat Thickness 0.3 mm
QUO‐LT‐041215‐15‐PDS R2 Form: TSD‐FCEN‐PDS‐R0
17/10/2016 16:10 Page: 3 of 21 Nov 25, 2012
P I P E D A T A S H E E T S
Project 10040 ‐ Fadhili Gas Program (FGP)
Client UTE TR (Tecnicas Reunidas)
Service Oily Water & Sanitary Sewer (1FE0U01) ‐
Installation Type Burried ‐
System Thrust Balance Restrained ‐
Product Type GRE ‐
Manufacturing Process Helical Filament Winding ‐
Joint Type Adhesive Tapered Bell/Spigot ‐
Nominal Diameter 300 mm
Design Pressure 10.0 Barg
Site Hydrostatic Test Pressure 6.9 Barg
Required Vacuum Rating N/A Barg
Maximum Pipe Length 12,000 mm
Minimum Total Wall Thickness 5.1 mm
Liner Thickness 0.5 mm
Resin Type Epoxy ‐
Glass Type C‐Veil ‐
Structural Wall Thickness 4.3 mm
Resin Type Epoxy ‐
Glass Type E‐Glass ‐
Aggregate None ‐
Top Coat Thickness 0.3 mm
QUO‐LT‐041215‐15‐PDS R2 Form: TSD‐FCEN‐PDS‐R0
17/10/2016 16:10 Page: 4 of 21 Nov 25, 2012
P I P E D A T A S H E E T S
Project 10040 ‐ Fadhili Gas Program (FGP)
Client UTE TR (Tecnicas Reunidas)
Service Oily Water & Sanitary Sewer (1FE0U01) ‐
Installation Type Burried ‐
System Thrust Balance Restrained ‐
Product Type GRE ‐
Manufacturing Process Helical Filament Winding ‐
Joint Type Adhesive Tapered Bell/Spigot ‐
Nominal Diameter 350 mm
Design Pressure 10.0 Barg
Site Hydrostatic Test Pressure 6.9 Barg
Required Vacuum Rating N/A Barg
Maximum Pipe Length 12,000 mm
Minimum Total Wall Thickness 5.7 mm
Liner Thickness 0.5 mm
Resin Type Epoxy ‐
Glass Type C‐Veil ‐
Structural Wall Thickness 4.9 mm
Resin Type Epoxy ‐
Glass Type E‐Glass ‐
Aggregate None ‐
Top Coat Thickness 0.3 mm
QUO‐LT‐041215‐15‐PDS R2 Form: TSD‐FCEN‐PDS‐R0
17/10/2016 16:10 Page: 5 of 21 Nov 25, 2012
P I P E D A T A S H E E T S
Project 10040 ‐ Fadhili Gas Program (FGP)
Client UTE TR (Tecnicas Reunidas)
Service Oily Water & Sanitary Sewer (1FE0U01) ‐
Installation Type Burried ‐
System Thrust Balance Restrained ‐
Product Type GRE ‐
Manufacturing Process Helical Filament Winding ‐
Joint Type Adhesive Tapered Bell/Spigot ‐
Nominal Diameter 400 mm
Design Pressure 10.0 Barg
Site Hydrostatic Test Pressure 6.9 Barg
Required Vacuum Rating N/A Barg
Maximum Pipe Length 12,000 mm
Minimum Total Wall Thickness 6.5 mm
Liner Thickness 0.5 mm
Resin Type Epoxy ‐
Glass Type C‐Veil ‐
Structural Wall Thickness 5.7 mm
Resin Type Epoxy ‐
Glass Type E‐Glass ‐
Aggregate None ‐
Top Coat Thickness 0.3 mm
QUO‐LT‐041215‐15‐PDS R2 Form: TSD‐FCEN‐PDS‐R0
17/10/2016 16:10 Page: 6 of 21 Nov 25, 2012
P I P E D A T A S H E E T S
Project 10040 ‐ Fadhili Gas Program (FGP)
Client UTE TR (Tecnicas Reunidas)
Service Oily Water & Sanitary Sewer (1FE0U01) ‐
Installation Type Burried ‐
System Thrust Balance Restrained ‐
Product Type GRE ‐
Manufacturing Process Helical Filament Winding ‐
Joint Type Adhesive Tapered Bell/Spigot ‐
Nominal Diameter 450 mm
Design Pressure 10.0 Barg
Site Hydrostatic Test Pressure 6.9 Barg
Required Vacuum Rating N/A Barg
Maximum Pipe Length 12,000 mm
Minimum Total Wall Thickness 7.3 mm
Liner Thickness 0.5 mm
Resin Type Epoxy ‐
Glass Type C‐Veil ‐
Structural Wall Thickness 6.5 mm
Resin Type Epoxy ‐
Glass Type E‐Glass ‐
Aggregate None ‐
Top Coat Thickness 0.3 mm
QUO‐LT‐041215‐15‐PDS R2 Form: TSD‐FCEN‐PDS‐R0
17/10/2016 16:10 Page: 7 of 21 Nov 25, 2012
P I P E D A T A S H E E T S
Project 10040 ‐ Fadhili Gas Program (FGP)
Client UTE TR (Tecnicas Reunidas)
Service Oily Water & Sanitary Sewer (1FE0U01) ‐
Installation Type Burried ‐
System Thrust Balance Restrained ‐
Product Type GRE ‐
Manufacturing Process Helical Filament Winding ‐
Joint Type Adhesive Tapered Bell/Spigot ‐
Nominal Diameter 500 mm
Design Pressure 10.0 Barg
Site Hydrostatic Test Pressure 6.9 Barg
Required Vacuum Rating N/A Barg
Maximum Pipe Length 12,000 mm
Minimum Total Wall Thickness 7.9 mm
Liner Thickness 0.5 mm
Resin Type Epoxy ‐
Glass Type C‐Veil ‐
Structural Wall Thickness 7.1 mm
Resin Type Epoxy ‐
Glass Type E‐Glass ‐
Aggregate None ‐
Top Coat Thickness 0.3 mm
QUO‐LT‐041215‐15‐PDS R2 Form: TSD‐FCEN‐PDS‐R0
17/10/2016 16:10 Page: 8 of 21 Nov 25, 2012
P I P E D A T A S H E E T S
Project 10040 ‐ Fadhili Gas Program (FGP)
Client UTE TR (Tecnicas Reunidas)
Service Oily Water & Sanitary Sewer (1FE0U01) ‐
Installation Type Burried ‐
System Thrust Balance Restrained ‐
Product Type GRE ‐
Manufacturing Process Helical Filament Winding ‐
Joint Type Adhesive Tapered Bell/Spigot ‐
Nominal Diameter 600 mm
Design Pressure 10.0 Barg
Site Hydrostatic Test Pressure 6.9 Barg
Required Vacuum Rating N/A Barg
Maximum Pipe Length 12,000 mm
Minimum Total Wall Thickness 9.1 mm
Liner Thickness 0.5 mm
Resin Type Epoxy ‐
Glass Type C‐Veil ‐
Structural Wall Thickness 8.3 mm
Resin Type Epoxy ‐
Glass Type E‐Glass ‐
Aggregate None ‐
Top Coat Thickness 0.3 mm
QUO‐LT‐041215‐15‐PDS R2 Form: TSD‐FCEN‐PDS‐R0
17/10/2016 16:10 Page: 9 of 21 Nov 25, 2012
P I P E D A T A S H E E T S
Project 10040 ‐ Fadhili Gas Program (FGP)
Client UTE TR (Tecnicas Reunidas)
Service Oily Water & Sanitary Sewer (1FE0U01) ‐
Installation Type Burried ‐
System Thrust Balance Restrained ‐
Product Type GRE ‐
Manufacturing Process Helical Filament Winding ‐
Joint Type Lamination ‐
Nominal Diameter 700 mm
Design Pressure 10.0 Barg
Site Hydrostatic Test Pressure 6.9 Barg
Required Vacuum Rating N/A Barg
Maximum Pipe Length 12,000 mm
Minimum Total Wall Thickness 10.1 mm
Liner Thickness 0.5 mm
Resin Type Epoxy ‐
Glass Type C‐Veil ‐
Structural Wall Thickness 9.3 mm
Resin Type Epoxy ‐
Glass Type E‐Glass ‐
Aggregate None ‐
Top Coat Thickness 0.3 mm
QUO‐LT‐041215‐15‐PDS R2 Form: TSD‐FCEN‐PDS‐R0
17/10/2016 16:10 Page: 10 of 21 Nov 25, 2012
P I P E D A T A S H E E T S
Project 10040 ‐ Fadhili Gas Program (FGP)
Client UTE TR (Tecnicas Reunidas)
Service Oily Water & Sanitary Sewer (1FE0U01) ‐
Installation Type Burried ‐
System Thrust Balance Restrained ‐
Product Type GRE ‐
Manufacturing Process Helical Filament Winding ‐
Joint Type Lamination ‐
Nominal Diameter 900 mm
Design Pressure 10.0 Barg
Site Hydrostatic Test Pressure 6.9 Barg
Required Vacuum Rating N/A Barg
Maximum Pipe Length 12,000 mm
Minimum Total Wall Thickness 11.6 mm
Liner Thickness 0.5 mm
Resin Type Epoxy ‐
Glass Type C‐Veil ‐
Structural Wall Thickness 10.8 mm
Resin Type Epoxy ‐
Glass Type E‐Glass ‐
Aggregate None ‐
Top Coat Thickness 0.3 mm
QUO‐LT‐041215‐15‐PDS R2 Form: TSD‐FCEN‐PDS‐R0
17/10/2016 16:10 Page: 11 of 21 Nov 25, 2012
P I P E D A T A S H E E T S
Project 10040 ‐ Fadhili Gas Program (FGP)
Client UTE TR (Tecnicas Reunidas)
Service Oily Water & Sanitary Sewer (1FE0U01) ‐
Installation Type Burried ‐
System Thrust Balance Restrained ‐
Product Type GRE ‐
Manufacturing Process Helical Filament Winding ‐
Joint Type Lamination ‐
Nominal Diameter 1,200 mm
Design Pressure 10.0 Barg
Site Hydrostatic Test Pressure 6.9 Barg
Required Vacuum Rating N/A Barg
Maximum Pipe Length 11,000 mm
Minimum Total Wall Thickness 15.4 mm
Liner Thickness 0.5 mm
Resin Type Epoxy ‐
Glass Type C‐Veil ‐
Structural Wall Thickness 14.6 mm
Resin Type Epoxy ‐
Glass Type E‐Glass ‐
Aggregate None ‐
Top Coat Thickness 0.3 mm
QUO‐LT‐041215‐15‐PDS R2 Form: TSD‐FCEN‐PDS‐R0
17/10/2016 16:10 Page: 12 of 21 Nov 25, 2012
P I P E D A T A S H E E T S
Project 10040 ‐ Fadhili Gas Program (FGP)
Client UTE TR (Tecnicas Reunidas)
Service Oily Water & Sanitary Sewer (1FE0U01) ‐
Installation Type Burried ‐
System Thrust Balance Restrained ‐
Product Type GRV ‐
Manufacturing Process Continuous Filament Winding ‐
Joint Type Lamination ‐
Nominal Diameter 1,400 mm
Design Pressure 10.0 Barg
Site Hydrostatic Test Pressure 6.9 Barg
Required Vacuum Rating N/A Barg
Maximum Pipe Length 11,800 mm
Minimum Total Wall Thickness 17.3 mm
Liner Thickness 1.0 mm
Resin Type Vinyl Ester ‐
Glass Type C‐Veil + Chop ‐
Structural Wall Thickness 16.0 mm
Resin Type Vinyl Ester ‐
Glass Type E‐Glass ‐
Aggregate None ‐
Top Coat Thickness 0.3 mm
QUO‐LT‐041215‐15‐PDS R2 Form: TSD‐FCEN‐PDS‐R0
17/10/2016 16:10 Page: 13 of 21 Nov 25, 2012
P I P E D A T A S H E E T S
Project 10040 ‐ Fadhili Gas Program (FGP)
Client UTE TR (Tecnicas Reunidas)
Service Fire Water (1FE0W01) ‐
Installation Type Burried ‐
System Thrust Balance Restrained ‐
Product Type GRE ‐
Manufacturing Process Helical Filament Winding ‐
Joint Type Adhesive Tapered Bell/Spigot ‐
Nominal Diameter 25 mm
Design Pressure 16.0 Barg
Site Hydrostatic Test Pressure 24.0 Barg
Required Vacuum Rating N/A Barg
Maximum Pipe Length 3,000 mm
Minimum Total Wall Thickness 2.6 mm
Liner Thickness 0.5 mm
Resin Type Epoxy ‐
Glass Type C‐Veil ‐
Structural Wall Thickness 1.8 mm
Resin Type Epoxy ‐
Glass Type E‐Glass ‐
Aggregate None ‐
Top Coat Thickness 0.3 mm
QUO‐LT‐041215‐15‐PDS R2 Form: TSD‐FCEN‐PDS‐R0
17/10/2016 16:10 Page: 14 of 21 Nov 25, 2012
P I P E D A T A S H E E T S
Project 10040 ‐ Fadhili Gas Program (FGP)
Client UTE TR (Tecnicas Reunidas)
Service Fire Water (1FE0W01) ‐
Installation Type Burried ‐
System Thrust Balance Restrained ‐
Product Type GRE ‐
Manufacturing Process Helical Filament Winding ‐
Joint Type Adhesive Tapered Bell/Spigot ‐
Nominal Diameter 50 mm
Design Pressure 16.0 Barg
Site Hydrostatic Test Pressure 24.0 Barg
Required Vacuum Rating N/A Barg
Maximum Pipe Length 3,000 mm
Minimum Total Wall Thickness 2.6 mm
Liner Thickness 0.5 mm
Resin Type Epoxy ‐
Glass Type C‐Veil ‐
Structural Wall Thickness 1.8 mm
Resin Type Epoxy ‐
Glass Type E‐Glass ‐
Aggregate None ‐
Top Coat Thickness 0.3 mm
QUO‐LT‐041215‐15‐PDS R2 Form: TSD‐FCEN‐PDS‐R0
17/10/2016 16:10 Page: 15 of 21 Nov 25, 2012
P I P E D A T A S H E E T S
Project 10040 ‐ Fadhili Gas Program (FGP)
Client UTE TR (Tecnicas Reunidas)
Service Fire Water (1FE0W01) ‐
Installation Type Burried ‐
System Thrust Balance Restrained ‐
Product Type GRE ‐
Manufacturing Process Helical Filament Winding ‐
Joint Type Adhesive Tapered Bell/Spigot ‐
Nominal Diameter 80 mm
Design Pressure 16.0 Barg
Site Hydrostatic Test Pressure 24.0 Barg
Required Vacuum Rating N/A Barg
Maximum Pipe Length 6,000 mm
Minimum Total Wall Thickness 3.2 mm
Liner Thickness 0.5 mm
Resin Type Epoxy ‐
Glass Type C‐Veil ‐
Structural Wall Thickness 2.4 mm
Resin Type Epoxy ‐
Glass Type E‐Glass ‐
Aggregate None ‐
Top Coat Thickness 0.3 mm
QUO‐LT‐041215‐15‐PDS R2 Form: TSD‐FCEN‐PDS‐R0
17/10/2016 16:10 Page: 16 of 21 Nov 25, 2012
P I P E D A T A S H E E T S
Project 10040 ‐ Fadhili Gas Program (FGP)
Client UTE TR (Tecnicas Reunidas)
Service Fire Water (1FE0W01) ‐
Installation Type Burried ‐
System Thrust Balance Restrained ‐
Product Type GRE ‐
Manufacturing Process Helical Filament Winding ‐
Joint Type Adhesive Tapered Bell/Spigot ‐
Nominal Diameter 100 mm
Design Pressure 16.0 Barg
Site Hydrostatic Test Pressure 24.0 Barg
Required Vacuum Rating N/A Barg
Maximum Pipe Length 6,000 mm
Minimum Total Wall Thickness 3.2 mm
Liner Thickness 0.5 mm
Resin Type Epoxy ‐
Glass Type C‐Veil ‐
Structural Wall Thickness 2.4 mm
Resin Type Epoxy ‐
Glass Type E‐Glass ‐
Aggregate None ‐
Top Coat Thickness 0.3 mm
QUO‐LT‐041215‐15‐PDS R2 Form: TSD‐FCEN‐PDS‐R0
17/10/2016 16:10 Page: 17 of 21 Nov 25, 2012
P I P E D A T A S H E E T S
Project 10040 ‐ Fadhili Gas Program (FGP)
Client UTE TR (Tecnicas Reunidas)
Service Fire Water (1FE0W01) ‐
Installation Type Burried ‐
System Thrust Balance Restrained ‐
Product Type GRE ‐
Manufacturing Process Helical Filament Winding ‐
Joint Type Adhesive Tapered Bell/Spigot ‐
Nominal Diameter 150 mm
Design Pressure 16.0 Barg
Site Hydrostatic Test Pressure 24.0 Barg
Required Vacuum Rating N/A Barg
Maximum Pipe Length 12,000 mm
Minimum Total Wall Thickness 3.3 mm
Liner Thickness 0.5 mm
Resin Type Epoxy ‐
Glass Type C‐Veil ‐
Structural Wall Thickness 2.5 mm
Resin Type Epoxy ‐
Glass Type E‐Glass ‐
Aggregate None ‐
Top Coat Thickness 0.3 mm
QUO‐LT‐041215‐15‐PDS R2 Form: TSD‐FCEN‐PDS‐R0
17/10/2016 16:10 Page: 18 of 21 Nov 25, 2012
P I P E D A T A S H E E T S
Project 10040 ‐ Fadhili Gas Program (FGP)
Client UTE TR (Tecnicas Reunidas)
Service Fire Water (1FE0W01) ‐
Installation Type Burried ‐
System Thrust Balance Restrained ‐
Product Type GRE ‐
Manufacturing Process Helical Filament Winding ‐
Joint Type Adhesive Tapered Bell/Spigot ‐
Nominal Diameter 200 mm
Design Pressure 16.0 Barg
Site Hydrostatic Test Pressure 24.0 Barg
Required Vacuum Rating N/A Barg
Maximum Pipe Length 12,000 mm
Minimum Total Wall Thickness 4.1 mm
Liner Thickness 0.5 mm
Resin Type Epoxy ‐
Glass Type C‐Veil ‐
Structural Wall Thickness 3.3 mm
Resin Type Epoxy ‐
Glass Type E‐Glass ‐
Aggregate None ‐
Top Coat Thickness 0.3 mm
QUO‐LT‐041215‐15‐PDS R2 Form: TSD‐FCEN‐PDS‐R0
17/10/2016 16:10 Page: 19 of 21 Nov 25, 2012
P I P E D A T A S H E E T S
Project 10040 ‐ Fadhili Gas Program (FGP)
Client UTE TR (Tecnicas Reunidas)
Service Fire Water (1FE0W01) ‐
Installation Type Burried ‐
System Thrust Balance Restrained ‐
Product Type GRE ‐
Manufacturing Process Helical Filament Winding ‐
Joint Type Adhesive Tapered Bell/Spigot ‐
Nominal Diameter 250 mm
Design Pressure 16.0 Barg
Site Hydrostatic Test Pressure 24.0 Barg
Required Vacuum Rating N/A Barg
Maximum Pipe Length 12,000 mm
Minimum Total Wall Thickness 4.9 mm
Liner Thickness 0.5 mm
Resin Type Epoxy ‐
Glass Type C‐Veil ‐
Structural Wall Thickness 4.1 mm
Resin Type Epoxy ‐
Glass Type E‐Glass ‐
Aggregate None ‐
Top Coat Thickness 0.3 mm
QUO‐LT‐041215‐15‐PDS R2 Form: TSD‐FCEN‐PDS‐R0
17/10/2016 16:10 Page: 20 of 21 Nov 25, 2012
P I P E D A T A S H E E T S
Project 10040 ‐ Fadhili Gas Program (FGP)
Client UTE TR (Tecnicas Reunidas)
Service Fire Water (1FE0W01) ‐
Installation Type Burried ‐
System Thrust Balance Restrained ‐
Product Type GRE ‐
Manufacturing Process Helical Filament Winding ‐
Joint Type Adhesive Tapered Bell/Spigot ‐
Nominal Diameter 400 mm
Design Pressure 16.0 Barg
Site Hydrostatic Test Pressure 24.0 Barg
Required Vacuum Rating N/A Barg
Maximum Pipe Length 12,000 mm
Minimum Total Wall Thickness 7.4 mm
Liner Thickness 0.5 mm
Resin Type Epoxy ‐
Glass Type C‐Veil ‐
Structural Wall Thickness 6.6 mm
Resin Type Epoxy ‐
Glass Type E‐Glass ‐
Aggregate None ‐
Top Coat Thickness 0.3 mm
QUO‐LT‐041215‐15‐PDS R2 Form: TSD‐FCEN‐PDS‐R0
17/10/2016 16:10 Page: 21 of 21 Nov 25, 2012