Documente Academic
Documente Profesional
Documente Cultură
SERVICE MANUAL
CONTENTS
SPECIFICATIONS ···································································· 3
PANEL LAYOUT······································································· 4
CIRCUIT BOARD LAYOUT ······················································ 5
WIRING····················································································· 6
DIMENTIONS ··········································································· 7
BLOCK DIAGRAM ···································································· 8
DISASSEMBLY PROCEDURE················································· 9
IC BLOCK DIAGRAM ····························································· 11
CIRCUIT BOARDS ································································· 12
INSPECTIONS········································································ 17
PARTS LIST
This document is printed on chlorine free (ECF) paper with soy ink. OVERALL CIRCUIT DIAGRAM
PA 011553
HAMAMATSU, JAPAN
1.222K-496 Printed in Japan '00.11
Downloaded from www.Manualslib.com manuals search engine
CP2000
IMPORTANT NOTICE
This manual has been provided for the use of authorized Yamaha Retailers and their service personnel. It has been assumed that
basic service procedures inherent to the industry, and more specifically Yamaha Products, are already known and understood by
the users, and have therefore not been restated.
WARNING: Failure to follow appropriate service and safety procedures when servicing this product may result in personal
injury, destruction of expensive components and failure of the product to perform as specified. For these
reasons, we advise all Yamaha product owners that all service required should be performed by an authorized
Yamaha Retailer or the appointed service representative.
IMPORTANT: This presentation or sale of this manual to any individual or firm does not constitute authorization, certification,
recognition of any applicable technical capabilities, or establish a principal-agent relationship of any form.
The data provided is belived to be accurate and applicable to the unit(s) indicated on the cover. The research engineering, and
service departments of Yamaha are continually striving to improve Yamaha products. Modifications are, therefore, inevitable and
changes in specification are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist,
please contact the distributor's Service Division.
WARNING: Static discharges can destroy expensive components. Discharge any static electricity your body may have
accumulated by grounding yourself to the ground bus in the unit (heavy gauge black wires connect to this bus).
IMPORTANT: Turn the unit OFF during disassembly and parts replacement. Recheck all work before you apply power to the
unit.
WARNING
Components having special characteristics are marked and must be replaced with parts having specification equal to those
originally installed.
SPECIFICATIONS
Power Output Level 8 Ω/STEREO 450 W + 450 W
4 Ω/STEREO 650 W + 650 W
1 kHz, THD+N=1 %
8 Ω/BRIDGE 1300 W
1 kHz 2 Ω/STEREO 1000 W + 1000 W
20 ms, non-clip 4 Ω/BRIDGE 2000 W
Power Bandwidth THD+N=0.2 % (half power) 10 Hz—40 kHz
Total Harmonic Distortion (THD+N) 4–8 Ω/STEREO
0.1%
20 Hz–20 kHz (half power) 8 Ω/BRIDGE
Intermodulation Distortion 4–8 Ω/STEREO
0.1%
60 Hz:7 kHz, 4:1, half power 8 Ω/BRIDGE
Frequency Response 8 Ω, Po=1W 0 dB, +0.5 dB, -1 dB f=20 Hz—50 kHz
Channel separation Half power, RL=8 Ω
≥70 dB, 1 kHz
LEVEL=max., input 600 Ω shunt
Residual Noise LEVEL=min., 12.7 kHz LPF, IHF-A network ≤ -70 dB
S/N Ratio 12.7 kHz LPF 104 dB
Damping Factor RL=8 Ω, 1 kHz ≥200
Sensitivity LEVEL=max., rated power into 8 Ω +4 dB
Voltage Gain LEVEL=max. 33.8 dB
Input Impedance 30 kΩ (balanced), 15 kΩ (unbalanced)
POWER switch (push on/push off)
Front panel
LEVEL attenuator (31 position) x2
Controls
Mode switch (STEREO/BRIDGE/PARALLEL)
Rear panel
YAMAHA SPEAKER PROCESSING switch (ON/OFF)
XLR-3-31 type (balanced) L+R
Input
1/4" phone jack (balanced) L+R
Connectors
1/4" phone jack L+R
Output
5-way binding post x1
POWER x1 (green)
PROTECTION x1 (red)
TEMP x1 (red) heatsink temp ≥85 °C
Indicators
CLIP x2 (red)
x2 (green) output voltage ≥2 V
SIGNAL
x2 (yellow) output voltage ≥20 V
POWER switch on/off mute
DC detection
Protection Circuit
TEMP (heatsink temp ≥90 °C)
PC limiter: RL ≤1 Ω
Fan Circuit Stop–low speed (50 °C)–variable–high Speed (70 °C)
Limiter Circuit Comp: THD≥0.5 %
U.S.A. & Canada 120 V AC, 60 Hz
Power requirements Europe 230 V AC, 50 Hz
Australia 240 V AC, 50 Hz
Idle Power Consumption 30 W
1/8 Power Consumption (4 Ω) 400 W
Maximum Power Consumption (4 Ω) 2000 W
Dimensions (W x H x D) 480 x 88 x 416 mm (18.9 x 3.46 x 16.4 inches)
Weight 14 kg (30.9 lbs)
AC Power cord length 2.3 m
* 0 dB=0.775 V rms, half power = 1/2 output level.
PANEL LAYOUT
Front Panel
6 7
1 2 3 4 5
Rear Panel
8 11
9 10 12
CN616
CN617
CN615
70
CN303 CN305 CN304 CN302
AC 1/6
80
CN102
CN103
CN104
CN301
AC 2/6
IN PA
1 1
CN606 CN607 CN610
CN608 CN609
CN105
CN106
CN601 CN602
CN306
CN612 CN611
CN603
CN614
CN313
CN605
2 CN604
CN101 3
AC 3/6
• Wire Colors
U, V, T H, W, B A
1 BR BE RE
2 WH BE BE
3 BL BR BR
3NC2-V617020 2
CP2000
AC 6/6
WIRING
FAN AC 5/6 AC 1/6
POWER
TRANSFORMER
AC 4/6 POWER
switch
PA
AC 2/6
AC 3/6
IN
to Rear panel
AC cord
KEC-92573 3
DIMENTIONS
416
410
480
88
Unit: mm
CP2000
BLOCK DIAGRAM
AC 4/6
IN CHANNEL PA AC 3/6, 5/6, 6/6
BA L Lch Power Amp
IC302 ATT W607
SPEAKERS
3+ 1 RY101
1
JK301
- 3 Limiter
2 CN105
1 2 IC301 ON VR601
LD605
OFF SW302 JK601
CHANNEL L 3 LD606
(BRIDGE) LD604
(PARALLEL) SIGNAL
2 CLIP CHANNEL L
3
1
JK303
CN303 CN615 CN304 LD601
INV Temperature PROTECTION
6 7 Protection
INPUT YAMAHA
Sensor
Circuit LD603
SPEAKER (Heat Sink) L+R BRIDGE
IC302 TEMP
PROCESSING
JK302 CN616
1 2
2
LD609 CHANNEL R
3 CHANNEL Rch Power Amp
1 R PARALLEL
IC303 SW301 RY102
BA ATT BRIDGE
JK304 1
5+
7
STEREO Limiter
3 CN106 W609
-
6 ON VR602
IC301 JK602
OFF SW302
PA
CN302
POWER
LD602
POWER CIRCUIT CN614
+B
AC Cord E
-B
POWER SW
+24
SW601 AC 2/6, E FAN
-24
AC 1/6 Power transformer
KEC-92572 1
DISASSEMBLY PROCEDURE
1. Top Cover (time required: about 3 minutes) 4. AC2/6 Circuit Board
1-1 Remove the nine (9) screws marked [420]. The top cover (time required: about 15 minutes)
can then be removed. (Fig. 1) 4-1 Remove the top cover. (See procedure 1.)
4-2 Remove the AC3/6 circuit board. (See procedure 3.)
2. IN Circuit Board (time required: about 8 minutes) 4-3 Remove the screw marked [80A], the three (3) screws
2-1 Remove the top cover. (See procedure 1.) marked [120] and the two (2) screws marked [140]. The
2-2 Remove the six (6) screws marked [180], the four (4) screws AC2/6 circuit board and the DB angle can then be removed.
marked [290A] and the two (2) hexagonal nuts marked [A]. (Fig. 2, Fig. 4)
The IN circuit board can then be removed. (Fig. 2, Fig. 3)
5. Power Transformer
3. AC3/6 Circuit Board (time required: about 8 minutes)
(time required: about 10 minutes) 5-1 Remove the top cover. (See procedure 1.)
3-1 Remove the top cover. (See procedure 1.) 5-2 Remove the two (2) screws marked [103] and the
3-2 Remove the two (2) screws marked [320]. The speaker hexagonal bolt marked [C]. The transformer holder and
terminal cover can then be removed. (Fig. 3) the power transformer can then be removed. (Fig. 2, Fig. 4)
3-3 Remove the screw marked [290B], the two (2) screws
marked [300] and the two (2) hexagonal nuts marked [B].
The AC3/6 circuit board can then be removed. (Fig. 3)
[420]
AC 2/6
[120]
IN
DB angle
[420] [420]
[C]
[420]
[420]: Bind Head Tapping Screw-B 4.0X8 MFZN2BL (EG340190) [80A]: Bind Head Screw A4.0X8 MFZN2BL (VP156800)
[120]: Bind Head Tapping Screw-B 3.0X8 MFZN2BL (EP600190)
[160]: Bonding Tapping Screw-B 4.0X8 MFZN2BL (VR779900)
(Fig. 1) [180]: Bind Head Tapping Screw-B 3.0X8 MFZN2BL (EP600190)
(Fig. 2)
<Rear view> <Side view>
[290A] [320] [300] [320] [290B] DB angle
• PA Unit
[80B] [80B] [80B] AC 1/6 [50]
[60] x 2
PA Transistor holder (L)
AC 4/6
Power switch
knob
[40] Fan
[100A]
[D]
AC 6/6
PA AC 5/6
Transistor holder (R)
Attenuation knob
[100B]
[80B] [80B] [80B]
[250]
[250]: Oval Head Screw 4.0X8 MFZN2BL (VS153600)
9. AC1/6, AC4/6, AC5/6 and AC6/6 Circuit Board (Fig. 7)
(time required: about 20 minutes)
9-1 Remove the top cover. (See procedure 1.) 9-5 AC5/6 Circuit Board:
9-2 Remove the front panel (See procedure 8.) Remove the screw marked [100A]. The AC5/6 circuit board
9-3 AC1/6 Circuit Board: can then be removed. (Fig. 6)
Pull out the power switch knob. (Fig. 6) 9-6 AC6/6 Circuit Board:
Remove the two (2) screws marked [60]. The AC1/6 circuit Remove the screw marked [100B]. The AC6/6 circuit board
board can then be removed. (Fig. 6) can then be removed. (Fig. 6)
9-4 AC4/6 Circuit Board:
Pull out the attenuation knobs. (Fig. 6)
Remove the two (2) hexagonal nuts marked [D]. The AC4/6
circuit board can then be removed. (Fig. 6)
10
IC BLOCK DIAGRAM
+DC Voltage
+
Output A 1 +V 8 A B
Supply
Inverting - -
2 7 Output B
Input A - +
Non-Inverting 3 6
Inverting 1 2 3 4 5 6 7 8
Input A + - Input B
OUT -IN +IN -V +IN -IN OUT +V
-DC Voltage Supply 4 -V 5 Non-Inverting A A A B B B
Input B
Note: See parts list for details of circuit board component parts.
11
CIRCUIT BOARDS
IN Circuit Board A
to AC 2/6-CN614
to FAN
to AC 5/6
-CN616
to AC6/6
-CN617
to AC 4/6
-CN615
A'
to AC 2/6-
CN603
Component side
to AC 2/6- to AC 2/6-
CN601 CN602 Component side AC 6/6 Circuit Board
Component side
to IN-CN305
to IN-CN304 IN: 3NA-V607200 1
12
A
to PA-CN101
(BRIDGE)
CHANNEL L
ON
YAMAHA
SPEAKER
PROCESSING
OFF
INPUT
PARALLEL
BRIDGE
STEREO
CHANNEL R
Component side
A'
13
PA Circuit Board
B
3NA-V60721 1
14
Component side
B'
3NA-V60721 1
15
to Power
transformer
Component side
CN601: to AC 1/6-W601 CN606: to Power transformer CN611: to Power transformer
CN602: to AC 1/6-W602 CN607: to Power transformer CN612: to AC 3/6-W608
CN603: to AC 1/6-W603 CN608: to Power transformer W604: to PA-CN102
CN604: to AC cord (L) CN609: to Power transformer W605: to PA-CN103
CN605: to AC cord (N) CN610: to Power transformer W606: to PA-CN104
• Wire Colors
CN604 CN605 CN606, CN607
U, V, T BL WH BR
H, W, B BR BE BE
A BR BE RE
3NA-V607220 2
16
INSPECTIONS
1. Inspection during stereo mode and parallel mode
1.1 Preparations
Input attenuator MAX
Input terminal Cannon connector No. 2 hot; No. 1, 3 ground
Mode SW Stereo
Yamaha speaker processing Off
Output terminal Resistance load 4 Ω, Non inductance resistor, input capacitance 500 W or more.
Others Unless otherwise specified, drive both channels unless otherwise specified.
<Top View>
1.2 Inspection and adjustment AC 3/6
1.2.1 Fan and temperature indicator
The fan shall operate when the two jumper wires inside the frame marked AC 2/6 PA IN
FAN-C inside sheet IN are shorted. Next, the temperature indicator shall
come on when the two jumper wires inside the frame marked TM-C are TM-C
shorted. (Refer to the figure to the right for FAN-C, TM-C.) FAN-C
1.2.5 Gain
An output voltage of +24.0 ± 0.5 dBu shall be attained when 1 kHz, -10.0 dBu sine wave is input to the input terminal.
This inspection shall also be performed in the PARALLEL mode.
17
1.2.10 Stability
The following conditions shall be met when a 10 kHz, -10dBu rectangular pulse is input and a capacitance of 10 pf ~ 0.47 µF is
connected in parallel with a load resistance of 4 Ω.
Overshoot Vp/Vo < = 1.8
Ringing: Within 5 waves
Next, when there is only a pure capacitance of 10 pf ~ 0.47 µF the following conditions shall be met.
Vp/Vo <= 2.5
Ringing: There shall be convergence within 7 waves and no oscillation, etc.
1.2.12 Efficiency
(1) The primary electrical power shall be measured and be within the range shown below when a 1 kHz, -6.6 dBu sine wave is input
to the input terminal.
330 W ± 50 W (U: 4.0 A ± 0.6 A, H: 2.0 A ± 0.3A)
(2) The primary electrical power shall be measured and be within the range shown below when the input terminal is grounded by the
introduction of the input terminal.
25 W ± 10 W (U: 0.33 A ± 0.13 A, H: 0.20 A ± 0.08 A)
2. Bridge mode
2.1 Preparations
Input attenuator L channel only operates. Set to MAX.
Input terminal L channel cannon connector (No. 2 hot, No. 1, 3 ground)
Mode SW Bridge
Yamaha speaker processing Off
Output terminal Use L channel +, R channel +.
Load resistance 4 Ω + 4Ω, Non inductance resistor, input capacitance 500 W or more.
Measurement connection Set to a floating ground and connect at center point of load resistance.
SPEAKERS MEASURING
INSTRUMENT
INPUT
GND
2.2 Inspection
2.2.1 Gain
An output voltage of +24.0 ± 1.0 dBu shall be attained when a 1 kHz, -10 dBu sine wave is input to the input terminal.
18
4. Others
A DIN audio filter shall be used for the measurement of the noise level.
0 dBu=0.775 V
19
PARTS LIST
CONTENTS
OVERALL ASSEMBLY······························································································································ 2
ELECTRICAL PARTS ························································································································· 5~12
WARNING
Components having special characteristics are marked and must be replaced with parts having
specification equal to those originally installed.
OVERALL ASSEMBLY
400 50 40 40a
70
420 410 60
290 310
330
320
390
130 180
160 145
250 370
140 80
102 380
30
210
103 90
170
101
95
97
100
20 340 350
10
96
* V6170800 PA Unit
P10 -- Heat Sink (V617230)
P20 VV086500 Support H=7.4 B=5.5 6 01
* P30 V6072100 Circuit Board PA
P40 EG330290 Bind Head Screw SP 3.0X8 MFZN2Y 6 01
* P50 V6172500 Insulation Sheet TBM51W T=0.15 2
* P60 V6172600 Transistor Holder LEFT
* P70 V6172700 Transistor Holder RIGHT
P80 VQ074600 Bind Head Tapping Screw-B 3.0X12 MFZN2BL 18 01
ELECTRICAL PARTS
REF NO. PART NO. DESCRIPTION REMARKS QTY RANK
IN
2 2
CHANNEL L
INPUT
3 3
CHANNEL R
OP AMP
4 4
Fan
5 5
REGULATOR
OP AMP
6 to AC 2/6 CN614 6
to AC 5/6 CN616
to PA CN101
7 7
KEC-92569 1
to IN CN303
8 Power Transformer 8
AC 1/6 AC 2/6
to CN609 or 611
to CN610
to CN609 or 611
POWER
AC 4/6 KEC-92570 3
Switch
L LEVEL Controls R
to CN613
KEC-92570 3
to IN CN304
9 AC Cord 9
to IN CN301
AC 5/6 KEC-92570 3
10 10
to IN CN305
to PA CN102
to PA CN103
to PA CN104
KEC-92570 3
from AC3/6 W608
11 11
F601 F602 F603 F604 J603,604 C604,610,616,K601 RY601 T101
U, V, T 12A 250V 12A 250V 1A 250V 1A 250V XY980
H, W, B T5AH T5AH T1AL T1AL XY981
A: Australian model
A T5AH T5AH T1AL T1AL XZ157 B: British model AC 6/6 KEC-92570 3
: installed : not installed H: North European model
• Wire Colors U: U.S.A. model
CN604 CN605 CN606, CN607 T: Taiwan model
U, V, T BL WH BR V: General export model (110 V)
W: General export model (220 V)
H, W, B BR BE BE
A BR BE RE
12 12
PA
not used
13 13
to IN CN306
14 14
Note : See parts list for details of circuit board
AC 3/6 component parts.
CHANNEL L
NJM7815FA(XD853A00) NJM7915FA(XD854A00)
REGULATOR +15V REGULATOR -15V
1 SPEAKERS
to AC2/6
CN612
from W609 32 32
1 1
CHANNEL R
1: OUTPUT 1: OUTPUT
2: COMMON 2: INPUT
16 3: INPUT 3: COMMON
16
2
to PA CN106 FMU-22U(V4816400) RBV-2506 (V4833600)
DIODE STACK 10.0A 200V DIODE STACK 25.0A 600V
KEC-92570 3
not used
to REAR PANEL
17 17
CP2000 CP2000
Downloaded from
A
www.Manualslib.com
B
manuals
C
search engine
D E F G H I J K L