Documente Academic
Documente Profesional
Documente Cultură
Summary, fn this work the large-eddy simulation (LES) is used to investigate in-
compressible flow around a sphere with trip wire. The sphere is located in a channel
with square cross-section, and the bulk Reynolds number is Re = 50 000. The com-
putational effort implied by demands for sufficient spatial and temporal resolution
of the flow structures requires parallel runs on a high-performance computer. The
numerical results are compared to the experimental ones in order to provide reliable
data for testing, calibrating and improvement of statistical turbulence models. The
time-averaged LES-results and the measured data obtained by the laser-Doppler-
anemometry (LDA) for the velocity and the Reynolds-stress components are in
reasonable agreement. Accuracy of the predicted mean-flow velocity component is
particularly good. Comparison of the Reynolds stresses shows certain deviations in
the far wake, agreement is however acceptable from the qualitative point of view.
1 Introduction
Statistical turbulence models - those used to close the Reynolds-averaged
Navier-Stokes (RANS) equations which are commonly used in scientific and
engineering practice - suffer from severe deficiencies in the computation of
flows with transition and separation. They fail in the prediction of the drag
force and the wake structure. Appropriate assessment of applicability of these
models and their eventual improvement require reliable information not only
on integral values such as drag force but also d a t a on the velocity field and
the Reynolds-stress field in the entire flow, particularly in the wake.
T h e lack of d a t a on the velocity and the Reynolds-stress field in the wake
behind a sphere at high i?e-numbers motivated a series of investigations at
our department, including b o t h experimental and numerical work. Essential
190 M. Torlak, G. Jensen, I. Hadzic
2 Numerical m e t h o d
The starting point of LES is flltering the governing equations over a length
scale. For Newtonian fluids, a modified form of the Navier-Stokes equations
for incompressible fiow extended for the t e r m of the SGS-stress tensor is
obtained:
(1)
dxi
takes place either through the Message Passing Interface (MPI) hbrary or
ParaUel Virtual Machine (PVM).
3 Problem description
The accompanying experiments were conducted in a closed wind tunnel
with square cross-section. T h e dimensions of the test section are 300 m m x
300 m m x 600 mm. The geometry of the sphere with position of the trip wire
and the dimensions is depicted in Fig. 1 (left). T h e sphere was placed at the
centre of the tunnel, and fixed by a supporting bar from its rear side, in the
wake. Thus, influence of the sphere support onto the development of the flow
was retained as small as possible.
trip wire
Fig. 1. Geometry of the sphere with trip wire and dimensions in mm (left). A part
of the solution domain with only a quarter being shown (right)
Fig. 2. Longitudinal section of the computational grid around the sphere with trip
wire. Only upper part is shown. The grid consists of about 3.1 • 10^ CVs. Two levels
of local refinement — around the sphere and in the wake (left), and additional
refinement in the area of expected separation (right) can be clearly seen
maximum of about 0.75, and it was about 1.5 along the wall of the support
bar for x > 1.3D.
T h e time step size was At ^ 0.005D/Uo- T h e time averaging of the flow
properties (velocity, pressure, Reynolds-stress) started after SOD/Uo- T h e
subsequent averaging time in the simulation was taver ~ l^OD/Uo-
4 Computational aspects
The computational runs for the grid with about 3.1 • 10^ CVs were per-
formed parallel in space, using 64 processing units on the computer Cray
T 3 E . After automatic partitioning of the solution domain, about 47000 com-
putational points were assigned to a processing unit. Finer partitioning would
increase time overheads in the communication between the processing units.
The achieved load balancing was:
Np
99.9% (4)
NpvNp
where Np is the total number of computational points in the overall solution
domain, A^pu is the number of processing units, and Np is the maximum
number of computational points per processing unit. Here, Np also represents
dimension of the matrix of systems of equations to be solved. Several other
values used in the computational set-up which indicate consumption of the
computing resources are given in Tab. 1.
5 Results
In Fig. 3, the instantaneous fields of the mean-flow velocity component (left)
and the pressure (right) are shown. The turbulent boundary layer separates
194 M. Torlak, G. Jensen, I. Hadzic
Table 1. Computational set-up parameters and the resulting computing effort per
time step
start of the time averaging after 16 000 time steps
averaging period 30 000 time steps
number of averaging samples 30 000 (for each time step)
time step size 2.5- 10-^ s
convergence tolerance for outer iterations 10-^
maximum number of outer iterations required per 9
time step
computing time per time step about 65 s
from the rear side of the sphere, and is directed towards the mean-flow axis of
the channel. In the wake, whose width approximately equals the sphere diam-
eter, local velocity and pressure variations indicate a strongly turbulent flow
structure. The oscillatory n a t u r e of the velocity iso-lines, seen in front of the
trip wire, was triggered by the non-orthogonal grid along the non-matching
faces which are introduced by the local refinement. An instantaneous shot
from the fiow visualisation [2] is shown in Fig. 4. The instantaneous veloc-
ity vectors in the vicinity of the trip-wire are presented in Fig. 5. Laminar
boundary layer separates from the frontal side of the wire. Small vortices
which are generated behind the wire and trigger transition to turbulence in
the boundary layer are clearly seen.
Fig. 3. The iso-lines of the mean-flow velocity component Ux (left) and the pressure
(right) at an instant of time
Fig. 6 (left) shows the time- and circumferentially averaged pressure dis-
P-PQ
tribution. A profile of the averaged pressure coefficient Cp along
a meridian of the sphere is depicted in Fig. 6 (right). In the region in front of
LES of Flow Around a Sphere with Trip Wire at Re = 50 000 195
LES, Re=50.000
invisicid fluid,
smooth sphere
_i_
90 120 150
the trip wire, the pressure variation is similar to the one for flow around the
smooth sphere. Certain increase of the pressure in front of the trip wire and
a severe pressure drop behind it are noticeable. T h e variation of Cp is actually
continuous across the wire, and the pressure j u m p noticeable in the diagram
is due to distribution of interpolating points employed in the post-processing
stage. Interestingly, distribution of Cp does not show the minimum value at
a distinct value of the meridional angle (p. Instead, minimum of Cp extends
over a short range of (/?, indicating flat distribution of Cp behind the trip
wire. Shortly before the equator, about (/? = 85° measured from the frontal
stagnation point, the adverse pressure gradient arises, which is strong until
about 100°. Further, Cp increases and approaches zero in the vicinity of the
supporting bar while remaining negative. Slight local maximum of Cp around
170° is addressed to the effects induced by the supporting bar.
In Fig. 7, the time-averaged velocity vectors obtained from LES (left) are
compared to the time-averaged velocities obtained by LDA-measurements
(right). The vectors are constructed using the mean-flow component, Ux, and
radial component, Ur- A qualitatively good agreement of the global flow pat-
tern is observed in the simulation. Approximately at 105° measured from the
frontal stagnation point, flow separation is observed. The main flow stream
re-attached the support behind the sphere, bounding a recirculation area
about 0.95D long. Based on the LDA-measurements [2] the separation point
was visually estimated at the angle of 120° and the length of recirculation
196 M. Torlak, G. Jensen, I. Hadzic
area of about ID. T h e raster of the samphng points in the measurements was
too coarse near the sphere wah, so t h a t the very thin layer of backward flow
in the range between 105° and 120° could not be recorded.
A detailed quantitative comparison of the mean-flow velocity component
is shown in Fig. 8 (above). Agreement of the results in the vicinity of the
sphere and the near wake is very good. Deviations from the measured val-
ues are noticeable in the upper part of the far wake, for x/D > 1, where
LES LDA
Fig. 7. The time-averaged velocity in the wake of the sphere: LES results (left)
and LDA measurements (right)
x/D=0
x/D=0.167
x/D=0.333
x/D=0.500
x/D=0.667
x/D=0.833
x/D=1.000
x/D=1.167
x/D=1.333
x/D=1.500
x/D=1.667
x/D=1.833
0.5 1 1.5
x/D + 0.25 (U/U^)
x/D=0
x/D=0.167
x/D=0.333
x/D=0.500
x/D=0.667
x/D=0.833
x/D=1.000
x/D=1.167
x/D=1.333
x/D=1.500
x/D=1.667
x/D=1.833
0 0.5 1 1.5 2
x/D + sqrtiujjJ/U^
Fig. 8. Profiles of the normalised mean-flow velocity component UX/UQ (above) and
normalised Reynolds stress \/UXUX/UQ (below): LES results (lines) and measured
values (symbols)
LES of Flow Around a Sphere with Trip Wire at Re = 50 000 197
10 f
id
Q. 10't
^10'
10 10
16' log St
Fig. 9. Fourrier transformation of the velocity (red) and pressure (blue) time his-
tories at a point immediately behind the trip wire (left) and a point in the far wake
(right)
Fig. 10. The invariant map of the anisotropy tensor for the flow around the sphere
with trip wire at Re = 50 000
Table 2. Global flow properties obtained after time averaging: (*) numerical results
from [6], (o) numerical results from [4], (o) experimental results from [2], and (•)
present numerical results
the sphere with the trip wire is clearly less t h a n for the smooth sphere. This
finding is in accordance with experience. Unfortunately, measured values of
the drag force for the case investigated here are not available for a more
precise verification.
The flow around sphere with trip wire is substantially different t h a n for
smooth sphere. Locations of maxima and minima b o t h in the velocity and
the Reynolds-stress field, as well as their intensities differ [2]. Principally, the
flow structure is predicted by LES b o t h qualitatively and quantitatively well.
While quantitative discrepancies between the computed and measured values
of the Reynolds-stress in the far wake are observed in the present simulation,
comparison with the numerical results from [6] for smooth sphere shows t h a t
LES has predicted all changes in the right direction and also largely with the
right magnitude.
6 Conclusions
In this paper, it is shown t h a t LES captures all phenomena of separated flow
around a sphere with transition to turbulence. Prediction of the flow around
LES of Flow Around a Sphere with Trip Wire at Re = 50 000 199
a sphere using LES is much better t h a n with RANS-models, which may give
quahtatively wrong results for this type of flow, particularly drag force and
turbulence quantities.
Since LES is too expensive for every-day simulations, the RANS-models
still have to be used in engineering practice. Therefore, they need to be
assessed in detail by performing a term-by-term analysis. T h e LES results
can be used to validate new RANS-models or the ideas for improvement
of existing ones, since - contrary to experimental work - LES delivers all
necessary information for assessment of modelling assumptions. T h e accom-
panying experiments provide sufficient d a t a to confirm quality of the LES
results.
Further LES has to be performed on the finer grids, in order to examine
still noticeable deviations from experimental data. W i t h this validated LES
d a t a a term-by-term analysis of RANS turbulence models can be performed
in order to identify their deficiencies. Also, URANS and DES can be assessed
against the d a t a obtained from the LES simulation.
Acknowledgements
T h e financial support provided by Deutsche Forschungsgemeinschaft (DFG)
within the project grant No. P E 350/15-2 is gratefully acknowledged. It is
also the authors' pleasure to t h a n k Dr. Milovan Peric, CD adapco Group,
for many helpful discussions. The computations were performed using the
program Comet on the computer Cray T 3 E of Hochstleistungsrechenzentrum
(HLRS) S t u t t g a r t , Germany.
References
1. Comet, Version 2.000 - User Manual CD adapco Group, 2000.
2. V. Bakic. Experimental investigation of turbulent flows around a sphere. PhD
thesis, TU Hamburg-Harburg, Arbeitsbereiche Schiffbau, Bericht 621, 2003.
3. I. Demirdzic and S. Muzaferija. Numerical method for coupled fluid flow, heat
transfer and stress analysis using unstrucutred moving meshes with cells of ar-
bitrary topology. Comput. Methods Appl. Mech. Engrg., 125:235-255, 1995.
4. I. Hadzic, V. Bakic, M. Peric, V. Sajn, and F. Kosel. Experimental and numerical
studies of flow around sphere at sub-critical Reynolds number. In 5th Int. Symp.
on Engineering Turbulence Modelling and Measurements, Mallorca, Spain, 16-18
Sept. 2002, 2002.
5. K. Hanjalic, I. Hadzic, and S. Jakirlic. Modelling turbulent wall flows subjected
to strong pressure variations. Journal of Fluids Engineering, 125:235-, 1998.
6. M. Schmid. Crobstruktursimulation turbulenter Stromungen auf unstrukturi-
erten Cittern mit einer parallelen Finite-Volumen Methode. PhD thesis, TU
Hamburg-Harburg, Arbeitsbereiche Schiffbau, Bericht 616, 2002.
200 M. Torlak, G. Jensen, I. Hadzic