Documente Academic
Documente Profesional
Documente Cultură
PROJECT
II. LOADING
2.1 Roof Loading
I.
DESIGN CRITERIA
Roof LRT Project , are use steel construction. The project site is located at Jl. Kelapa
Gading North Jakarta.
Sub Structure
Sub structure of the building is using existing foundation by others.
An early stage of planning is studying the structure of the system that can be used by
following the requirements which is defined or specified by the architect and the mechanical
& electrical and determine loadings depend on the function of its chambers, then do an early
design to determine the dimensions of the components of the structure.
Structural analysis using SAP program V14.00 with 3-Dimensional analysis was modeled as
a 3-D frame. Geometry defined structure of the line and column spans relationships
whichproduced 3-D structure of the frame.
The calculation of seismic forces, carried out with a dynamic 3-D analysis (Model Analysis)
by applying elastic response spectrum as specified in SNI 1726-2012.
The results dynamic analysis is used to perform seismic shear force distribution on each
floor. The pattern distribution of dynamic seismic forces are then used in static analysis.
Calculation of reinforcement beams and columns are done with SAP program with the load
coefficient calculations are based on SNI 1726-2012 regulations. Reinforced concrete
reinforcement planning for each element follows the structure and the combination of
strength reduction factors such as SNI 2847-2013 regulations.
3. CODE USED
Planning this structure of this building, in all things complied with all regulations and the
conditions with applicable in Indonesia. The rules were as follows :
The Planning Of Procedures Earthquake Resistance for the Building
( SNI 1726-2012)
The Procedurs For The design Steel Sructure Of Buildings (SNI 1929-2015).
The Procedurs For The design Concrete Sructure Of Buildings (SNI 2847-2013).
The Guideline Planning of Loading For Home and Building (SNI 1727-2013).
1
4. Material Spesification
5. LOADING COMBINATION
For planning elements of beams and columns follow the rule standard procedures planning
structure concrete to the building sni 2847-2013 , on strong need to .In accordance with sni
2847-2013 , the influence of earthquake considered work in two the direction of the axis main
in simultaneously , which is 100 % of earthquake directions combined with a 30 % major
earthquake the straight vertical direction. Combination loading for fixed and temporary load
, the next is as follows:
1. U = 1.4 D
2. U = 1.2 D + 1.6 L + 0.5(Lr atau R)
3. U = 1.2 D + 1.6 ( Lr atau R ) + (L atau 0.5W)
4. U = 1.2 D ± 1.0 W + L+ 0.5 ( Lr atau R )
5. U = 1.2 D ± 1.0 E + L
6. U = 0.90 D ± 1.0 W
7. U = 0.90 D ± 1.0 E
Whereas:
D = Dead load
L = Live load
W = Wind load
Lr = Roof live load
R = Rain Load
E = Earthquake Load
H = Lateral soil pressure
6. LOADING
2
6.2. Live Load
Live load used in accordance with Indonesian Loading Regulation, is based on each function
room. For rooms that have special functions assigned individually.
Ir. Suhartoyo
SIBP : No. 93/8.6.1//31/-1.785.5/2016
3
CALCULATION STRUCTURE
REPORT
II.
LOADING
2.1 Roof Loading
WIND LOAD
Wind Load Assumption = 25 Kg/m2
Span Between Column = 7.5 m
a = 27
SAP2000 v14.0.0 - File:ATAP PULOMAS-R2 - Frame Span Loads (DL) (As Defined) - Kgf, m, C Units
SAP2000 8/24/17 17:54:02
SAP2000 v14.0.0 - File:ATAP PULOMAS-R2 - Frame Span Loads (LL) (As Defined) - Kgf, m, C Units
SAP2000 8/24/17 17:53:07
SAP2000 v14.0.0 - File:ATAP PULOMAS-R2 - Frame Span Loads (WL) (As Defined) - Kgf, m, C Units
CALCULATION STRUCTURE
REPORT
III.
q sin a trekstang
a
q cos a
q
Wind Load :
Pressure Of Wind = 25 kg/m2
Wind Load, at wind (+0.02α - 0.4) = 3.5 kg/m2 (pressure)
(qa x s) = 6.475 kg/m'
V
M
V baut
M baut
IV.
0. 1. 1. 1. 1.
SAP2000 v14.0.0 - File:ATAP PULOMAS-R2 - Steel P-M Interaction Ratios (AISC-LRFD99) - Kgf, m, C Units
SAP2000 8/24/17 16:51:30
0. 1. 1. 1. 1.
SAP2000 v14.0.0 - File:ATAP PULOMAS-R2 - Steel P-M Interaction Ratios (AISC-LRFD99) - Kgf, m, C Units
SAP2000 8/24/17 16:51:16
0. 1. 1. 1. 1.
SAP2000 v14.0.0 - File:ATAP PULOMAS-R2 - Steel P-M Interaction Ratios (AISC-LRFD99) - Kgf, m, C Units
SAP2000 8/24/17 16:51:04
0. 1. 1. 1. 1.
SAP2000 v14.0.0 - File:ATAP PULOMAS-R2 - Steel P-M Interaction Ratios (AISC-LRFD99) - Kgf, m, C Units
SAP2000 8/24/17 16:50:53
0. 1. 1. 1. 1.
SAP2000 v14.0.0 - File:ATAP PULOMAS-R2 - Steel P-M Interaction Ratios (AISC-LRFD99) - Kgf, m, C Units
SAP2000 8/24/17 16:50:16
0. 1. 1. 1. 1.
SAP2000 v14.0.0 - File:ATAP PULOMAS-R2 - Steel P-M Interaction Ratios (AISC-LRFD99) - Kgf, m, C Units
SAP2000 8/24/17 16:57:58
0. 1. 1. 1. 1.
SAP2000 v14.0.0 - File:ATAP PULOMAS-R2 - Steel P-M Interaction Ratios (AISC-LRFD99) - Kgf, m, C Units
ATAP PULOMAS-R2.SDB SAP2000 v14.0.0 - License #
24 August 2017
Page 1 of 2
ATAP PULOMAS-R2.SDB SAP2000 v14.0.0 - License #
24 August 2017
Page 2 of 2
ATAP PULOMAS-R2.SDB SAP2000 v14.0.0 - License #
24 August 2017
Page 1 of 6
ATAP PULOMAS-R2.SDB SAP2000 v14.0.0 - License #
24 August 2017
Page 2 of 6
ATAP PULOMAS-R2.SDB SAP2000 v14.0.0 - License #
24 August 2017
Page 3 of 6
ATAP PULOMAS-R2.SDB SAP2000 v14.0.0 - License #
24 August 2017
Page 4 of 6
ATAP PULOMAS-R2.SDB SAP2000 v14.0.0 - License #
24 August 2017
Page 5 of 6
ATAP PULOMAS-R2.SDB SAP2000 v14.0.0 - License #
24 August 2017
Page 6 of 6