Sunteți pe pagina 1din 35

Republic of the Philippines

Department of Health

BILL OF QUANTITIES

CONSTRUCTION OF PRESIDENTIAL SECURITY GROUP STATION HOSPITAL PHASE 1


Malacañang Park, Manila
Project Name and Location

Item
DESCRIPTION QTY UNIT UNIT COST TOTAL COST
No.
A. GENERAL REQUIREMENTS
a.1 Mobilization/Demobilization (%age of civil works) 0.75 %
a.2 Utilities (Power, Water and Communications) 9.00 months
a.3 Security 9.00 months
a.4 Permits, clearances & other Gov't Taxes 1.00 lot
a.5 Temporary Facility, Warehouse, Office 1.00 lot
SUB-TOTAL A

B. SOIL/EARTHWORKS
b.1 Excavation 760.00 cu.mts.
b.2 Backfill and Compaction 2,055.60 cu.mts.
b.3 Gravel Fill 280.00 cu.mts.
b.4 Soil Poisoning 2,575.00 sq.m.
SUB-TOTAL B

C. FOUNDATION/PILE WORKS
c.1 500mm x 500mm concrete pile (L = 15m) 8,040.00 mts
c.2 Pile Density Analyzer (PDA) test 5.00 piles
SUB-TOTAL C

D. CONCRETE AND REBAR WORKS


d.1 Ready Mix Concrete (3000 psi) 287.00 cu.m.
d.2 Ready Mix Concrete (4000 psi) 2,147.10 cu.m.
d.3 25mmØ RSB 194,498.67 kgs.
d.4 20mmØ RSB 98,424.47 kgs.
d.5 16mmØ RSB 6,511.47 kgs.
d.6 12mmØ RSB 142,924.88 kgs.
d.7 10mmØ RSB 13,483.41 kgs.
d.8 Formworks and plywood 2,500.00 pcs
d.9 scaffoldings 37,500.00 bd.ft
d.10 tiewires 160.00 roll
SUB-TOTAL D

E. DEMOLITION OF EXISTING BUILDING

e.1 1 - unit air compressor with two jackhammer 200.00 hrs


e.2 1 - unit backhoe/breaker 120.00 hrs
e.3 2 - units dumptruck 120.00 hrs
e.4 1 - unit oxy/acetelene cutter 30.00 days
e.5 1 - General Foreman 30.00 days
e.6 20 - laborers 30.00 days
SUB-TOTAL E

F. EQUIPMENT RENTALS/EXPENSES (Building construction)

f.1 1 - unit loader 200.00 hrs


f.2 1 - unit backhoe/breaker 240.00 hrs
f.3 2 - units dumptruck 200.00 hrs
f.4 1 - unit truck mounted crane 200.00 hrs
f.5 1 - unit static pile hammer 536.00 position
f.6 1 - unit trailer (hauling of piles) 89.00 trips
SUB-TOTAL F

Page 1 of 35
Republic of the Philippines
Department of Health

BILL OF QUANTITIES

CONSTRUCTION OF PRESIDENTIAL SECURITY GROUP STATION HOSPITAL PHASE 1


Malacañang Park, Manila
Project Name and Location

Item
DESCRIPTION QTY UNIT UNIT COST TOTAL COST
No.
A. GENERAL REQUIREMENTS TOTAL STRUCTURAL WORKS
B ARCHITECTURAL WORKS
B.1 MASONRY WORKS
Supply and installation of CHB in cement sand & mortar (1:3)
including reinforcement as shown in drawings
CHB 150mm thick to exterior walls( exterior walls 1st and 2nd
1.1 9500 sq.m
Floor and inner wall of ground floor)
1.2 CHB 100mm thick to interior walls( 2nd floor only ) 1200 sq.m
SUB-TOTAL

B.2 FINISHING CONCRETE


Supply and install plain cement-plastered walls (100mm thk
2.1 2400 sq.m
CHB)
Supply and install plain cement-plastered walls including
2.2 19000 sq.m
skimcoating (150mm thk CHB)
SUB-TOTAL

B.3 MOISTURE PROTECTION / ROOFING / WATERPROOFING


Supply and installation of 0.6mm thk. Pre painted rib type long
3.1 span roofing including bended accessories,rafter and purlins 290 sq.m
(powerhouse, cadaver holding room and supply office)
Provision and installation of PE Foam Insulation (10mm x 1m x
3.2 40 rollS
50m - 2 sided)
Supply and installation of 6mm thk. Solid polycarbonate, this
includes the joining clip, edge clip, tek screws with o-ring gasket
3.3 315 sq.m
and silicon insulations, Tubular purlins, bracing an diagonal
support
Supply and application of waterproofing membrane at Elevator pit
3.4 1600 sq.m
and elevator shaft and roof slab
Supply and application of waterproofing membrane at balcony
3.5 360 sq.m
and exterior hallways at second floor
3.6 Supply and application of waterproofing membrane in all toilets 182 sq.m
SUB-TOTAL

B.4 CEILING FINISHES


CF. 1 Supply and install 4.5mm thk Fiber Cement Board on Light
Steel Framing System including all necessary hardwares and
fixing accessories, jointing, maintenance manhole and usage of
4.1 3000 sq.m
scaffolding temporary platforms, equipment and tools necessary
to complete all works ( this includes the building with
powerhouse, cadaver holding room and supply room )
CF. 2 Supply and installation of aluminum metal cladding ceiling /
4.2 260 sq.m
spandrel ceiling with ceiling ventilation at soffit
SUB-TOTAL

B.5 FINISHING METAL WORKS / RAILINGS


Supply and installation of grab bar/ railings 50mm Ø Stainless
5.1 150 lm
Steel Pipe at PWD toilet
Supply and installation of 2.5mm x 150mm x 200mm x 10mts
stainless tubular vertical facade louver, horizontal trellis above
5.2 the exterior hallway on the ground floor. This includes all the 220 pcs.
specialized welding rod, construction forms and other tools
needed to complete the works

Page 2 of 35
Republic of the Philippines
Department of Health

BILL OF QUANTITIES

CONSTRUCTION OF PRESIDENTIAL SECURITY GROUP STATION HOSPITAL PHASE 1


Malacañang Park, Manila
Project Name and Location

Item
DESCRIPTION QTY UNIT UNIT COST TOTAL COST
No.
A. GENERAL REQUIREMENTS
Supply and install glass railings and stainless handrail at ramp,
5.3 stairs interior and exterior hallway/balcony at second floor of the 180 lm
building, including all accessories needed to complete the work

Supply and install 2mm thk. x 25mm x 25mm square tubing


5.4 window grill, Epoxy Primed & Acrylic Painted 6mm thk. 50mm X 640 sq.m
50mm Baseplate bolted on concrete. Window grill should be
fabricated in accordance with the location of window handles
SUB-TOTAL

B.6 DOORS
D-1. (1600MM X 2200MM) 10mm thk. Frameless double panel
and double swing tempered glass on powder coated white
6.1 4 sets
aluminum frame complete with hardwares and fixing accessories
to complete the works per Architect's specifications
D-2. (1600MM X 2200MM) 10mm thk. Two leaf double swing
tempered glass on powder coated white aluminum frame
6.2 30 sets
complete with hardwares and fixing accessories to complete the
works per Architect's specifications
D-3. (800MM X 2200MM) 10mm thk. single leaf tempered glass
on powder coated white aluminum frame complete with
6.3 17 sets
hardwares and fixing accessories to complete the works per
Architect's specifications
D-4. (1000MM X 2200MM) 10mm thk. single leaf tempered glass
on powder coated white aluminum frame complete with
6.4 7 sets
hardwares and fixing accessories to complete the works per
Architect's specifications
D-5. (1200MM X 2200MM) 1/2" thk. Plywood painted flush type
6.5 door with 3/4" thk. Vision complete with hardwares and fixing 12 sets
accessories to complete the works per Architect's specifications
D-6. (800MM X 2200MM) Double sided aluminum flush type door
6.6 complete with hardwares and fixing accessories to complete the 11 sets
works per Architect's specifications
D-7. (600MM X 2200MM) Double sided aluminum flush type door
6.7 with louver vent complete with hardwares and fixing accessories 5 sets
to complete the works per Architect's specifications
D-8. (800MM X 2200MM) Double sided aluminum flush type door
with 3/4" thk. Side vision glass complete with hardwares and
6.8 48 sets
fixing accessories to complete the works per Architect's
specifications
D-9. (1000MM X 2200MM) Double sided aluminum flush type
door with 3/4" thk. Side vision glass complete with hardwares
6.9 10 sets
and fixing accessories to complete the works per Architect's
specifications
D-10. (1900MM X 2200MM) 10mm thk. Two leaf sliding
tempered glass door on powder coated white aluminum frame
6.10 3 sets
complete with hardwares and fixing accessories to complete the
works per Architect's specifications
D-11. (800MM X 2100MM) Double sided aluminum flush type
door with 3/4 thk. Vision glass and louver vent complete with
6.11 5 sets
hardwares and fixing accessories to complete the works per
Architect's specifications

Page 3 of 35
Republic of the Philippines
Department of Health

BILL OF QUANTITIES

CONSTRUCTION OF PRESIDENTIAL SECURITY GROUP STATION HOSPITAL PHASE 1


Malacañang Park, Manila
Project Name and Location

Item
DESCRIPTION QTY UNIT UNIT COST TOTAL COST
No.
A. GENERAL REQUIREMENTS
D-12. (1000MM X 2100MM) Double sided aluminum flush type
door with 3/4 thk. Vision glass and louver vent complete with
6.12 5 sets
hardwares and fixing accessories to complete the works per
Architect's specifications
D-13. (600MM X 2100MM) Double sided aluminum flush type
door with 3/4 thk. Vision glass and louver vent complete with
6.13 17 sets
hardwares and fixing accessories to complete the works per
Architect's specifications
D-14. (1200MM X 2200MM) 10mm thk. Tempered glass sliding
door on powder coated white aluminum frame complete with
6.14 2 sets
hardwares and fixing accessories to complete the works per
Architect's specifications
D-15. (4900MM X 2850MM) 4 leaf bullet proof glass sliding door
on powder coated white aluminum frame complete with
6.15 1 set
hardwares and fixing accessories to complete the works per
Architect's specifications
D-16. (2750MM X 2850MM) 2 leaf bullet proof glass sliding door
on powder coated white aluminum frame complete with
6.16 1 set
hardwares and fixing accessories to complete the works per
Architect's specifications
D-17. (1000MM X 2200MM) double sided aluminum flush type
7.16 door complete with hardwares and fixing accessories to complete 1 set
the works per Architect's specifications
D-18. (600MM X 1650MM) double sided aluminum flush type
8.16 door with louver vent complete with hardwares and fixing 4 sets
accessories to complete the works per Architect's specifications

D-19. (1300MM X 2100MM) 2 leaf 3/4 thk. Glass door on powder


6.17 coated white aluminum frame complete with hardwares and fixing 3 sets
accessories to complete the works per Architect's specifications

D-20. (1950MM X 2800MM) 1" x 1" x 2.5mm thk. Stainless steel


6.18 vertical louver type door complete with hardwares and fixing 2 sets
accessories to complete the works per Architect's specifications

D-23. aluminum roll up door complete with hardwares and fixing


6.19 1 set
accessories to complete the works per Architect's specifications
D-24. doors with lead shielding complete with hardwares and
7.19 fixing accessories to complete the works per Architect's 14 sq.m
specifications
SUB-TOTAL

B.7 WINDOWS
Aluminum Windows:

Supply & installation of 6mm thk. Glass on aluminum powder


coated white finish complete with hardwares and fixing
accessories to complete the works per Architect's specifications
W-1 (4700mm X 1250mm) seamless powder coated white
7.1 10 sets
aluminum framed glass awning type window.
W-2 (4700mm X 1250mm) seamless powder coated white
7.2 6 sets
aluminum framed glass awning type window.
W-3 (4550mm X 1250mm) seamless powder coated white
7.3 1 set
aluminum framed glass awning type window.
W-4 (2500mm X 1250mm) seamless powder coated white
7.2 20 sets
aluminum framed awning type window
W-5 (2000mm X 1250mm) seamless powder coated white
7.3 8 set
aluminum framed awning type window
Page 4 of 35
Republic of the Philippines
Department of Health

BILL OF QUANTITIES

CONSTRUCTION OF PRESIDENTIAL SECURITY GROUP STATION HOSPITAL PHASE 1


Malacañang Park, Manila
Project Name and Location

Item
DESCRIPTION QTY UNIT UNIT COST TOTAL COST
No.
A.7.4
GENERAL REQUIREMENTS
W-6 (1500mm X 1250mm) seamless powder coated white
12 sets
aluminym framed awning type window
W-7 (1200mm X 1250mm) seamless powder coated white
7.5 2 set
aluminum framed awning type window
W-8 (1000mm X 1250mm) seamless powder coated white
7.6 8 sets
aluminum framed awning type window
W-9 (800mm X 1250mm) seamless powder coated white
7.7 8 sets
aluminum framed awning type window
W-10 (600mm X 1250mm) seamless powder coated white
7.8 1 set
aluminum framed awning type window
W-11 (1200mm X 5000mm) powder coated white aluminum
7.9 2 sets
frame fixed glass window
W-12 (1200mm X 4700mm) powder coated white aluminum
7.10 2 set
framed fixed glass window
W-13 (1800mm X 2900mm) powder coated white aluminum
7.11 1 set
frame fixed glass window
W-14 (2500mm X 1200mm) powder coated white aluminum
7.12 9 sets
frame fixed glass window
W-15 (2000mm X 1200mm) powder coated white aluminum
7.13 2 sets
frame fixed glass window
W-16 (1500mm X 1200mm) powder coated white aluminum
7.14 9 sets
frame fixed glass window
W-17 (1200mm X 1200mm) powder coated white aluminum
7.15 10 sets
frame fixed glass window
W-18 (1000mm X 1200mm) powder coated white aluminum
7.16 13 sets
frame fixed glass window
W-19 (800mm X 1200mm) powder coated white aluminum
7.17 7 set
frame fixed glass window
W-20 (600mm X 1200mm) powder coated white aluminum
7.18 12 sets
frame fixed glass window
W-21 (5000mm X 600mm) seamless glass on powder coated
7.19 2 sets
white aluminum frame awning type window
W-22 (4700mm X 600mm) powder coated white aluminum
7.20 1 set
frame awning type window
W-24 (2500mm X 600mm) seamless glass on powder coated
7.21 2 sets
white aluminum frame awning type window
W-25 (2000mm X 600mm) seamless glass on powder coated
7.22 5 sets
white aluminum frame awning type window
W-26 (1500mm X 600mm) seamless glass on powder coated
7.23 9 sets
white aluminum frame awning type window
W-27 (1200mm X 600mm) seamless glass on powder coated
7.24 12 sets
white aluminum frame awning type window
W-28 (1000mm X 600mm) seamless glass on powder coated
7.25 8 sets
white aluminum frame awning type window
W-29 (800mm X 600mm) seamless glass on powder coated
7.26 2 sets
white aluminum frame awning type window
W-30 (600mm X 500mm) seamless glass on powder coated
7.27 1 set
white aluminum frame awning type window
W-31 (2000mm X 1200mm) powder coated white aluminum
7.28 2 sets
framed fixed glass window
W-32 (800mm X 1200mm) powder coated white aluminum
7.29 1 set
framed fixed glass window
W-33 (4700mm X 1200mm) seamless, one way and bullet proof
7.30 glass on powder coated white aluminum framed awning type 1 set
window
W-34 (2000mm X 1200mm) seamless, one way and bullet proof
7.31 glass on powder coated white aluminum framed awning type 2 sets
window

Page 5 of 35
Republic of the Philippines
Department of Health

BILL OF QUANTITIES

CONSTRUCTION OF PRESIDENTIAL SECURITY GROUP STATION HOSPITAL PHASE 1


Malacañang Park, Manila
Project Name and Location

Item
DESCRIPTION QTY UNIT UNIT COST TOTAL COST
No.
A. GENERAL REQUIREMENTS
W-35 (1200mm X 1200mm) seamless, one way and bullet proof
7.32 glass on powder coated white aluminum framed awning type 3 sets
window
W-36 (5000mm X 1200mm) powder coated white aluminum
7.33 1 set
framed fixed glass window
W-37 (1200mm X 1200mm) powder coated white aluminum
7.34 2 sets
framed fixed glass window
W-38 (1000mm X 1200mm) powder coated white aluminum
7.35 2 sets
framed fixed glass window
W-39 (4700mm X 600mm) seamless and bullet proof glass on
7.36 1 set
powder coated white aluminum framed awning type window
W-40 (2500mm X 600mm) seamless, one way and bullet proof
7.37 glass on powder coated white aluminum framed awning type 1 set
window
W-41 (1200mm X 600mm) seamless, one way and bullet proof
7.38 glass on powder coated white aluminum framed awning type 2 sets
window
W-42 (1000mm X 600mm) seamless, one way and bullet proof
7.39 glass on powder coated white aluminum framed awning type 2 sets
window
W-43 (2000mm X 1250mm) powder coated white aluminum
7.40 1 set
frame combined fixed and sliding window
W-44 (1200mm X 1200mm) powder coated white aluminum
7.41 1 set
frame combined fixed and sliding window
W-45 (2000mm X 1250mm) powder coated white aluminum
7.42 7 sets
frame combined fixed and sliding window
W-47 (2000mm X 600mm) powder coated white aluminum
7.43 2 sets
frame louver/ grilles type window
W-48 (5000mm X 1200mm) powder coated white aluminum
7.44 2 sets
frame louver/ grilles type window
W-49 (4550mm X 1200mm) powder coated white aluminum
7.45 1 sets
frame louver/ grilles type window
W-52 (4700mm X 2200mm) seamless glass on powder coated
8.44 1 set
white aluminum frame detachable type window
Supply and installation of Mechanically operated louver type
9.44 ventillation at skylight with all necessary accessories to complete 70 sq.m
the works
Supply and installation of 10mm thk. Glass on powder coated
7.45 white aluminum framed windows on supply room and cadaver 50 sq.m
holding room.
SUB-TOTAL

B.8 FLOOR FINISHES


FF-1. Supply and installation of 600mm x 600mm x 6mm thk.
Shades of gray synthetic granite floor tiles, including application
8.1 950 sq.m
of approved tile grout, tile adhesive and all necessary
accessories to complete all works
FF-2. Supply and installation of 600mm x 600mm non-skid
8.2 polished floor tiles including application of approved tile grout, tile 1800 sq.m
adhessive and all necessary accessories to complete the works
FF-3. Supply and installation of hard wood planks with
polyurethane top coat finish including wood glue and all
8.3 80 sq.m
necessary accessories to complete the works ( hyperbaric
chamber room and prayer room)
FF-4. Supply and installation of antibacterial polyvinyl chloride
8.4 flooring including adhessives and all necessary accessories to 230 sq.m
complete the works (presidential suite area)
Page 6 of 35
Republic of the Philippines
Department of Health

BILL OF QUANTITIES

CONSTRUCTION OF PRESIDENTIAL SECURITY GROUP STATION HOSPITAL PHASE 1


Malacañang Park, Manila
Project Name and Location

Item
DESCRIPTION QTY UNIT UNIT COST TOTAL COST
No.
A. GENERAL REQUIREMENTS
FF-5. Supply and installation of 200mm x 200mm Shades of gray
non-skid ceramic floor tiles, including application of approved tile
8.5 182 sq.m
grout, tile adhesive and all necessary accessories to complete all
works (all toilets )
FF-6. Supply and installation of 200mm x 200mm Shades of gray
non-skid ceramic floor tiles (rough finish) with bronze nosing,
8.6 70 sq.m
including application of approved tile grout, tile adhesive and all
necessary accessories to complete all works

FF-7. Supply and installation of 400mm x 400mm shades of gray


non-skid ceramic floor tiles (high quality), including application of
8.7 12 sq.m
approved tile grout, tile adhesive and all necessary accessories
to complete all works ( presidential suite toilet )

FF-8. Supply and installation of rough topping/ finish with 10mm


grooves at 200mm O.C. painted with clorinated rubber based
8.8 214 sq.m
floor coating, including application of approved epoxy sealer as
primer and all necessary accessories to complete all works

B.9 WALL FINISHES


Supply and install WF-6 (200mm x 300mm) glossy glazed
9.1 ceramic wall Tiles including tile grout, tile adhesive, tile trim and 350 sq.m
all necessary accessories to complete all works
Supply and install WF-6 at presidential suite toilet (200mm x
300mm) glossy glazed ceramic wall Tiles with approved accent
9.2 40 sq.m
wall tiles including tile grout, tile adhesive, tile trim and all
necessary accessories to complete all works
Supply and installation of lead shielding in x-ray room and ct-
9.3 scan room (walls only) and all necessary accessories to 170 sq.m
complete all works
SUB-TOTAL

B.10 CARPENTRY AND GENERAL WORKS


Supply and installation of cabinets and shelves in the presidential
suite, this includes the shelves, cabinets in the closet, dressing
10.1 60.0 sq.m
area, and wash area in the toilet. This includes painting and other
types of finishing.
Supply and installation of cabinets, overhanging cabinets ,
cupboards and cabinets under the wash area in every toilet in
10.2 300.0 sq.m
phase 01 and phase 02 this includes painting preparations and
high standard finishing touches.

Supply and construct 25mm thk. Solid surface counter top with
100 mm high splash board, under counter cabinets/drawer &
10.3 overhead cabinets with 6mm thk. Clear glass in 19mm thk. HPL 40.0 sq.m
(High Pressure Laminate) finish at laboratory, dental complex,
private rooms/icu and physical and neuro examination.
including hardwares and accessories (see detailed drawings)
SUB-TOTAL

B.11 PAINTING WORKS


Exterior
WF 1. Supply and application self priming elastomeric exterior
11.1 paint shades of gray color, 3 coats; including use of tools & 2920 sq.m
equipment and all necessary items to complete the works

Page 7 of 35
Republic of the Philippines
Department of Health

BILL OF QUANTITIES

CONSTRUCTION OF PRESIDENTIAL SECURITY GROUP STATION HOSPITAL PHASE 1


Malacañang Park, Manila
Project Name and Location

Item
DESCRIPTION QTY UNIT UNIT COST TOTAL COST
No.
A. GENERAL REQUIREMENTS
WF 2. Supply and application of self priming elastomeric exterior
paint dark brown color with grooves 200 M.M. O.C., 3 coats;
11.2 1000 sq.m
including use of tools & equipment and all necessary items to
complete the works
WF 3. Supply and application of water based acrylic paint,
shades of white color, 3 coats; 1 base coat, 2 under coat, 3
11.3 220 sq.m
finishing coat, including use of tools & equipment and all
necessary items to complete the works
WF 4. Supply and application of odorless and anti bacterial
shades of white paint color, 3 coats; 1 base coat, 2 under coat, 3
11.4 19040 sq.m
finishing coat, including use of tools & equipment and all
necessary items to complete the works
CF1. Supply and application of flat latex paint including surface
preparation, sealer, fillers; with (1) basecoat, (2) under coats; (1)
11.5 2000 sq.m
finish coating; including use of tools & equipment and all
necessary items to complete the works
SUB-TOTAL

TOTAL ARCHITECTURAL WORKS

I. ELECTRICAL WORKS AND AUXILLARY WORKS


A Lighting Fixtures
1 140mm diameter LED recessed Circular Downlight 214 sets
15 Watts, 1050 lumens, 4000k, 220-240V, 60 Hz
2 1200mm x 300mm LED Slim panel, 40 watts, 6500k, 382 sets
3,200 Lumens, 220-240V, 60 Hz, 0.9 p.f
3 LED Emergency Light, 2X1 Watts SMT LED 109 sets
4V 4AH Sealed Lead Acid, charging time: 20 hrs,
4 LED Exit Sign, Red, Double face, 2 watts 31 sets
Thermoplastic Housing
SUB-TOTAL

B Wiring Devices
1 Single Pole Single Throw Switch(SPST), 16A, 250VAC 118 sets
Wide Series, White
2 Two Pole Single Throw Switch(2PST), 16A, 250VAC 33 sets
Wide Series, White
3 Three Pole Single Throw Switch(3PST), 16A, 250VAC 3 sets
Wide Series, White
4 Single Three-Way Switch, 16A, 250VAC 52 sets
Wide Series, White
5 2-Gang Three-Way Switch, 16A, 250VAC 14 sets
Wide Series, White
6 3-Gang Three-Way Switch, 16A, 250VAC 2 sets
Wide Series, White
7 Four-Way Switch, 16A, 250VAC 4 sets
Wide Series, White
8 1-Gang Convenience Outlet, 16A, 250VAC 101 sets
(For Exit and Emergency Lights)
9 Special Purpose Outlet, 20A, 250VAC 8 sets
10 Weatherproof Duplex Convenience Outlet, 16A, 230V w/ 10 sets
grounding-type (Hospital Grade)
11 Duplex Convenience Outlet, 16A, 230V w/ 186 sets
grounding-type (Hospital Grade)
SUB-TOTAL

C Roughing-In
1 20 mmΦ uPVC Pipe 1904 length
Page 8 of 35
Republic of the Philippines
Department of Health

BILL OF QUANTITIES

CONSTRUCTION OF PRESIDENTIAL SECURITY GROUP STATION HOSPITAL PHASE 1


Malacañang Park, Manila
Project Name and Location

Item
DESCRIPTION QTY UNIT UNIT COST TOTAL COST
No.
20 mmΦ REQUIREMENTS
A. 2GENERAL uPVC Adapter 2936 pcs.
3 20 mmΦ uPVC Coupling 952 pcs.
4 20 mmΦ Locknut & Bushing 2936 pcs.
5 25 mmΦ uPVC Pipe 15 length
6 25 mmΦ uPVC Adapter 6 pcs.
7 25 mmΦ uPVC Coupling 8 pcs.
8 25 mmΦ Locknut & Bushing 6 pcs.
9 32 mmΦ uPVC Pipe 162 length
10 32 mmΦ uPVC Adapter 30 pcs.
11 32 mmΦ uPVC Coupling 81 pcs.
12 32 mmΦ Locknut & Bushing 30 pcs.
13 40 mmΦ uPVC Pipe 22 length
14 40 mmΦ uPVC Adapter 10 pcs.
15 40 mmΦ uPVC Coupling 11 pcs.
16 40 mmΦ Locknut & Bushing 10 pcs.
17 50 mmΦ uPVC Pipe 45 length
18 50 mmΦ uPVC Adapter 20 pcs.
19 50 mmΦ uPVC Coupling 22 pcs.
20 50 mmΦ Locknut & Bushing 20 pcs.
21 63 mmΦ uPVC Pipe 6 length
22 63 mmΦ uPVC Adapter 2 pcs.
23 63 mmΦ uPVC Coupling 3 pcs.
24 63 mmΦ Locknut & Bushing 2 pcs.
25 75 mmΦ uPVC Pipe 73 length
26 75 mmΦ uPVC Adapter 32 pcs.
27 75 mmΦ uPVC Coupling 37 pcs.
28 75 mmΦ Locknut & Bushing 32 pcs.
29 110 mmΦ UPVC Pipe 44 pcs.
30 110 mmΦ UPVC Adopter 20 pcs.
31 110 mmΦ UPVC Coupling 22 pcs.
32 110 mmΦ Locknut & Bushing 20 pcs.
33 40 mmΦ RSC Pipe w/ Coupling 1 length
34 40 mmΦ RSC Elbow 2 length
35 40 mmΦ RSC Locknut & Bushing 2 length
36 50 mmΦ RSC Pipe w/ Coupling 2 length
37 50 mmΦ RSC Elbow 4 length
38 50 mmΦ RSC Locknut & Bushing 4 length
39 65 mmΦ RSC Pipe w/ Coupling 1 length
40 65 mmΦ RSC Elbow 2 length
41 65 mmΦ RSC Locknut & Bushing 2 length
42 90 mmΦ RSC Pipe w/ Coupling 2 length
43 90 mmΦ RSC Elbow 4 length
44 90 mmΦ RSC Locknut & Bushing 4 length
45 100 mmΦ RSC Pipe w/ Coupling 1 length
46 100 mmΦ RSC Elbow 2 length
47 100 mmΦ RSC Locknut & Bushing 2 length
48 Junction Box w/ Cover 1303 pcs.
49 Utility Box 771 pcs.
50 Pullbox 35 pcs.
51 Cable Tray System 1 lot
SUB-TOTAL

D Wires and Cables


1 3.5 sq. mm. THWN 108 rolls
2 5.5 sq. mm. THWN 2 rolls
3 5.5 sq. mm. TW 1 roll
4 8.0 sq. mm. THWN 3 rolls
5 8.0 sq. mm. TW 0.5 roll
6 14 sq. mm. TW Page 9 of 35 50 mts
Republic of the Philippines
Department of Health

BILL OF QUANTITIES

CONSTRUCTION OF PRESIDENTIAL SECURITY GROUP STATION HOSPITAL PHASE 1


Malacañang Park, Manila
Project Name and Location

Item
DESCRIPTION QTY UNIT UNIT COST TOTAL COST
No.
A. 7GENERAL REQUIREMENTS
22 sq. mm. TW 50 mts
8 30 sq. mm. THWN 1040 mts
9 30 sq. mm. TW 20 mts
10 80 sq. mm. THWN 90 mts
11 100 sq. mm. THWN 90 mts
12 200 sq. mm. THWN 384 mts
SUB-TOTAL

E Panelboards, Circuit Breakers and Equipments


1 CB in NEMA Enclosure 6 assy
40AT/100AF,400V, 10 KAIC ,3P,BO

2 CB in NEMA Enclosure 6 assy


60AT/100AF,400V, 10 KAIC ,3P,BO

3 ELSPB1- Main : 40AT/100AF, 3P 1 assy


400VAC, 25 KAIC
Bolt-On MCCB
Branches : 18 - 20AT/100AF, 240 V, 10 KAIC, 1P

4 ELSPB2- Main : 40AT/100AF, 3P 1 assy


400VAC, 25 KAIC
Bolt-On MCCB
Branches : 12 - 20AT/100AF, 240 V, 10 KAIC, 1P

5 ECP1, ECP2 & ECP3 - Main : 100AT/100AF, 3P 3 assy


240VAC, 25 KAIC
Bolt-On MCCB
Branches : 18 - 20AT/100AF, 240 V, 10 KAIC, 1P

6 EEBP1A Main : 100AT/100AF, 3P 1 assy


400VAC, 25 KAIC
Bolt-On MCCB
Branches : 6 - 30AT/100AF, 240 V, 10 KAIC, 3P

7 EEBP1B - Main : 300AT/400AF, 3P 1 assy


400VAC, 42 KAIC
Bolt-On MCCB
Branches : 1 - 200AT/225AF, 400 V, 42 KAIC, 3P
1 - 150AT/225AF, 400 V, 42 KAIC, 3P
2 - 100AT/100AF, 400 V, 42 KAIC, 3P

8 EEBP2 & EEBP3 - Main : 100AT/400AF, 3P 2 assy


400VAC, 42 KAIC
Bolt-On MCCB
Branches : 1 - 40AT/100AF, 400 V, 25 KAIC, 3P
7 - 30AT/100AF, 400 V, 25 KAIC, 3P

9 NLP1 Main : 175AT/225AF, 3P 1 assy


400VAC, 42KAIC
Bolt-On MCCB
Branches : 31 - 20AT/100AF, 240 V, 10 KAIC, 1P
9 - 30AT/100AF, 240 V, 10 KAIC, 1P
2 - 40AT/100AF, 240 V, 10 KAIC, 1P

10 NLP2 Main : 100AT/100AF, 3P 1 assy


400VAC, 42KAIC
Bolt-On MCCB
Branches : 19 - 20AT/100AF, 240 V, 10 KAIC, 1P Page 10 of 35
Republic of the Philippines
Department of Health

BILL OF QUANTITIES

CONSTRUCTION OF PRESIDENTIAL SECURITY GROUP STATION HOSPITAL PHASE 1


Malacañang Park, Manila
Project Name and Location

Item
DESCRIPTION QTY UNIT UNIT COST TOTAL COST
No.
A. GENERAL REQUIREMENTS
4 - 30AT/100AF, 240 V, 10 KAIC, 1P
1 - 40AT/100AF, 240 V, 10 KAIC, 1P

11 NLP3 Main : 100AT/100AF, 3P 1 assy


400VAC, 42KAIC
Bolt-On MCCB
Branches : 34 - 20AT/100AF, 240 V, 10 KAIC, 1P
2 - 40AT/100AF, 240 V, 10 KAIC, 1P

12 PPACU 1 : 200AT/225AF, 3P 1 assy


400VAC, 42KAIC
Bolt-On MCCB
Branches : 6 - 60AT/100AF, 400 V, 10 KAIC, 3P

13 PPACU 2 : 175AT/225AF, 3P 1 assy


400VAC, 42KAIC
Bolt-On MCCB
Branches : 2 - 60AT/100AF, 400 V, 10 KAIC, 3P
4 - 40AT/100AF, 240 V, 10 KAIC, 3P

14 PPACU 3 : 125AT/225AF, 3P 1 assy


400VAC, 42KAIC
Bolt-On MCCB
Branches : 6 - 40AT/100AF, 400 V, 10 KAIC, 3P

15 EDP1 Main : 100AT/100AF, 3P 1 assy


400VAC, 42KAIC
Bolt-On MCCB
Branches : 6 - 40AT/100AF, 240 V, 10 KAIC, 1P

16 MEEBP - Main : 600AT/600AF, 3P 1 assy


400VAC, 85KAIC
Bolt-On MCCB
Branches : 6 - 100AT/100AF, 400 V, 25 KAIC, 3P
3 - 300AT/100AF, 400 V, 42 KAIC, 3P

17 MNLP : 500AT/600AF, 3P 1 assy


400VAC, 85KAIC
Bolt-On MCCB
Branches : 2 - 100AT/100AF, 400 V, 25 KAIC, 3P
1 - 150AT/100AF, 400 V, 42 KAIC, 3P
1 - 175AT/100AF, 400 V, 42 KAIC, 3P
18 NDP1- Main : 150AT/225AF, 3P 1 assy
240VAC, 42KAIC
Bolt-On MCCB
Branches : 5 - 50AT/100AF, 240 V, 25 KAIC, 2P
1 - 70AT/100AF, 240V, 25 KAIC, 1P
1 - 70AT/100AF, 400V, 25 KAIC, 3P

19 MPPACU - Main : 500AT/600AF, 3P 1 assy


400VAC, 85KAIC
Bolt-On MCCB
Branches : 1 - 100AT/100AF, 400 V, 25 KAIC, 3P
1 - 125AT/225AF, 400 V, 25 KAIC, 3P
1 - 175AT/225AF, 400 V, 25 KAIC, 3P
1 - 200AT/225AF, 400 V, 25 KAIC, 3P

20 MPOGP & PP-Fire - Main : 100AT/100AF, 3P 2 assy


400VAC, 25KAIC Page 11 of 35
Republic of the Philippines
Department of Health

BILL OF QUANTITIES

CONSTRUCTION OF PRESIDENTIAL SECURITY GROUP STATION HOSPITAL PHASE 1


Malacañang Park, Manila
Project Name and Location

Item
DESCRIPTION QTY UNIT UNIT COST TOTAL COST
No.
A. GENERAL REQUIREMENTS
Bolt-On MCCB
Branches : 2 - 40AT/100AF, 400 V, 10 KAIC, 3P
6 - 40AT/100AF, 240 V, 10 KAIC, 1P

21 PP-STP- Main : 100AT/100AF, 3P 1 assy


400VAC, 25KAIC
Bolt-On MCCB
Branches : 10 - 30AT/100AF, 400 V, 10 KAIC, 3P
7 - 20AT/100AF, 240 V, 10 KAIC, 1P

22 MNDP - Main : 1200AT/1200AF, 3P 1 assy


400VAC, 125KAIC
Bolt-On MCCB
Branches : 1 - 100AT/100AF, 400 V, 42 KAIC, 3P
1 - 150AT/225AF, 400 V, 42 KAIC, 3P
2 - 500AT/600AF, 400 V, 85 KAIC, 3P
Bolt-on Circuit Breaker
w/complete Metering Devices as follows:
Masterpact NW Air Circuit Breaker with electronic
Meter Micrologic Control Unit of 2.0A.
in NEMA-1, free standing, ANSI-49 paint gauge
#14 with lugs and extension busbars.
W/complete Ammeter Metering Devices
to all branch sub-breakers.

23 MEDP - Main : 1000AT/1000AF, 3P 1 assy


400VAC, 125KAIC
Bolt-On MCCB
Thermal Magnetic ACB
Branches : 3 - 100AT/100AF, 400 V, 42 KAIC, 3P
1 - 250AT/225AF, 400 V, 85 KAIC, 3P
1 - 600AT/600AF, 400 V, 85 KAIC, 3P
Bolt-on Circuit Breaker
w/complete Metering Devices as follows:
Masterpact NW Air Circuit Breaker with electronic
Meter Micrologic Control Unit of 2.0A.
in NEMA-1, free standing, ANSI-49 paint gauge
#14 with lugs and extension busbars.
W/complete Ammeter Metering Devices
to all branch sub-breakers.

24 MDP - Main : 2000AT/2000AF, 3P 1 assy


240VAC, 125KAIC
Bolt-On MCCB
Thermal Magnetic ACB
Branches : 1 - 1200AT/1200AF, 400 V, 125 KAIC, 3P
1 - 1000AT/1000AF, 400 V, 125 KAIC, 3P
Bolt-on Circuit Breaker
w/complete Metering Devices as follows:
Masterpact NW Air Circuit Breaker with electronic
Meter Micrologic Control Unit of 2.0A.
in NEMA-1, free standing, ANSI-49 paint gauge
#14 with lugs and extension busbars.
W/complete Ammeter Metering Devices
to all branch sub-breakers.

25 MCB - Main : 2000AT/2000AF, 3P 1 assy


240VAC, 125KAIC
Bolt-On MCCB Page 12 of 35
Republic of the Philippines
Department of Health

BILL OF QUANTITIES

CONSTRUCTION OF PRESIDENTIAL SECURITY GROUP STATION HOSPITAL PHASE 1


Malacañang Park, Manila
Project Name and Location

Item
DESCRIPTION QTY UNIT UNIT COST TOTAL COST
No.
A. GENERAL REQUIREMENTS
Thermal Magnetic ACB
w/complete Analog Metering Devices as follows:
Voltages, Currents, Power, Frequency and
Power Factor to all incoming Phases and Lines.
in NEMA-1, free standing, ANSI-49 paint gauge
#14 with lugs and extension busbars.
26 Automatic Transfer Switch (ATS1) 1 assy
Main: 1000A, 3P, 400VAC, 125KAIC
27 Automatic Transfer Switch (ATS1) 1 assy
Main: 1200A, 3P, 400VAC, 125KAIC
28 Synchronizing Panel 1 assy
2-450KVA, 400 Volts, Three Phase
SUB-TOTAL
F Generator Sets
1 Brand New 450 KVA Standby Diesel Generator 1 assy
Standby 450kVA/360kW, 220-415 Volts, Three Phase
60Hz, 80%PF, Length 3500mm, Width 1110mm, Height
2158 & Weights 2814kg dry, Silent Type
SUB-TOTAL
G First Private Pole
1 Supply and Installation of the First Private Pole and 1 lot
Primary Lines Facilities with 3 - 250 kVA Transformer,
Single Phase, Pole Mounted and other accessories
SUB-TOTAL
H Related Civil Works
1 Service Entrance Pedestal 1 lot
2 Electrical Handhole (6 sets) 1 lot
SUB-TOTAL
I Miscellaneous
1 Electrical PVC Tape 90 rolls
2 G.I. Wire gauge 16 30 kgs
3 Hacksaw Blade 60 pcs
4 Assorted Tox, screw, nails, drill bits, etc. 1 lot
SUB-TOTAL

J Auxiliary System
J.1 Fire Detection and Alarm System
Auxiliary Devices
1 Smoke Detector 102 sets
2 Heat Detector 5 sets
3 Annunciator 7 sets
4 Fire Alarm Bell, 6 inch. Dia 18 sets
5 Fire Alarm Manual Push-Button Station 18 sets
Roughing-Ins
1 15 mmΦ EMT Pipe 319 length
2 15 mmΦ EMT Connector 160 pcs.
3 15 mmΦ EMT Locknut & Bushing 264 pcs.
4 25 mmΦ EMT Pipe 59 length
5 25 mmΦ EMT Connector 30 pcs.
6 25 mmΦ EMT Locknut & Bushing 24 pcs.
7 Utility Box 48 pcs
8 Junction Box 118 pcs
9 Hangers and Supports 1 lot
Wires and Cables
1 #16 AWG 2C TF Shielded Twisted Wire 7 rolls
Panelboards and Circuit Breakers
1 10 Zones FACP System with workstation, printer, 1 assy
firemans, telephone outlet, EVAC panel and UPS with
complete hardware and accessories Page 13 of 35
Republic of the Philippines
Department of Health

BILL OF QUANTITIES

CONSTRUCTION OF PRESIDENTIAL SECURITY GROUP STATION HOSPITAL PHASE 1


Malacañang Park, Manila
Project Name and Location

Item
DESCRIPTION QTY UNIT UNIT COST TOTAL COST
No.
A. GENERAL REQUIREMENTS
Miscellaneous
1 Electrical PVC Tape 10 rolls
2 G.I. Wire gauge 16 5 kgs
3 Hacksaw Blade 5 pcs
4 Assorted Tox, screw, nails, drill bits, etc. 1 lot
SUB-TOTAL

J.2 Public Address System/Background Music


1 Ceiling Mounted Speaker 32 sets
Roughing-Ins
1 15 mmΦ EMT Pipe 146 length
2 15 mmΦ EMT Connector 73 pcs.
3 15 mmΦ EMT Locknut & Bushing 64 pcs.
4 Junction Box 36 pcs
5 Hangers and Supports 1 lot
SUB-TOTAL

Wires and Cables


1 1.25 sq. mm. TF wires 3 rolls
Panelboards and Circuit Breakers
1 PA/EVAC System matrix controller, power amplifier 1 assy
PATB, paging microphone, pre-amplifier, pre-recorded
voice, EVAC panel and UPS complete hardware and
accessories
Miscellaneous
1 Electrical PVC Tape 5 rolls
2 G.I. Wire gauge 16 3 kgs
3 Hacksaw Blade 3 pcs
4 Assorted Tox, screw, nails, drill bits, etc. 1 lot
SUB-TOTAL

J.3 Structured Cabling


1 Combination RJ45 & RJ11 Port Universal Information 41 pcs
Outlet (Lan/Tel)
2 2-Gang Data Outlet 8 pcs
SUB-TOTAL

Roughing-Ins
1 25 mmΦ EMT Pipe 422 length
2 25 mmΦ EMT Connector 211 pcs.
3 25 mmΦ EMT Locknut & Bushing 54 pcs.
7 100mm(W)x50mm(D) with cover including 110 mts
connectors, couplings and bolts
8 200mm(W)x50mm(D) with cover including 70 mts
connectors, couplings and bolts
9 Hangers and Supports 1 lot
10 IDF 2 pcs
11 Utility Box 54 pcs
Wires and Cables
1 #24 AWG Cat6 UTP Cable 9 rolls
SUB-TOTAL

Panelboards and Circuit Breakers


1 Data Center complete with MDF, MTTC, IDF, TTC, 1 assy
IIPABX and uninterruptible power supply complete
hardware and accessories
SUB-TOTAL

Miscellaneous Page 14 of 35
Republic of the Philippines
Department of Health

BILL OF QUANTITIES

CONSTRUCTION OF PRESIDENTIAL SECURITY GROUP STATION HOSPITAL PHASE 1


Malacañang Park, Manila
Project Name and Location

Item
DESCRIPTION QTY UNIT UNIT COST TOTAL COST
No.
A. 1GENERAL
ElectricalREQUIREMENTS
PVC Tape 25 rolls
2 G.I. Wire gauge 16 10 kgs
3 Hacksaw Blade 8 pcs
4 Assorted Tox, screw, nails, drill bits, etc. 1 lot
SUB-TOTAL

J.4 Closed Circuit Television System


1 IP-based fixed colored cctv camera - dome type 11 pcs
2 Power Over Ethernet Switch 2 pcs
SUB-TOTAL

Roughing-Ins
1 15 mmΦ EMT Pipe 164 length
2 15 mmΦ EMT Connector 82 pcs.
3 15 mmΦ EMT Locknut & Bushing 15 pcs.
4 Hangers and Supports 1 lot
5 Junction Box 10 pcs
Wires and Cables
1 #24 AWG Cat6 UTP Cable 2 rolls
Panelboards and Circuit Breakers
SUB-TOTAL

1 CCTV System complete with switch, network 1 assy


video recorder, monitoring server, pan-tilt zoom
controller, LCD monitor, LCD spot monitor, un-interruptible power
supply, hardward and accessories
Miscellaneous
1 Electrical PVC Tape 10 rolls
2 G.I. Wire gauge 16 5 kgs
3 Hacksaw Blade 5 pcs
4 Assorted Tox, screw, nails, drill bits, etc. 1 lot
SUB-TOTAL

J.5 Nurse Call System


1 Nurse Call per Hub complete with audio visual 2 assy
nurse call station, corridor nurse call annunciator,
nurse call call complete with call points and door
light, single LED indicator.
2 Power Over Ethernet Switch 2 pcs
SUB-TOTAL

Roughing-Ins
1 15 mmΦ EMT Pipe 88 length
2 15 mmΦ EMT Connector 44 pcs.
3 15 mmΦ EMT Locknut & Bushing 47 pcs.
4 Hangers and Supports 1 lot
5 Utility Box 22 pcs
Wires and Cables
1 #24 AWG Cat6 UTP Cable 1 roll
Panelboards and Circuit Breakers
1 Nurse Call System complete with nurse call 1 assy
server, workstation, printer and uninterruptible
power supply, complete hardware and accessories
SUB-TOTAL

Miscellaneous
1 Electrical PVC Tape 5 rolls
2 G.I. Wire gauge 16 4 kgs
3 Hacksaw Blade Page 15 of 35 4 pcs
Republic of the Philippines
Department of Health

BILL OF QUANTITIES

CONSTRUCTION OF PRESIDENTIAL SECURITY GROUP STATION HOSPITAL PHASE 1


Malacañang Park, Manila
Project Name and Location

Item
DESCRIPTION QTY UNIT UNIT COST TOTAL COST
No.
A. 4GENERAL
Assorted REQUIREMENTS
Tox, screw, nails, drill bits, etc. 1 lot
SUB-TOTAL

J.6 Master Antenna Television System


1 MATV Outlet 13 pcs.
2 Hub Equipment, Splitter, MATV Equipment Cabinet 2 set
Roughing-Ins
1 15 mmΦ EMT Pipe 135 length
2 15 mmΦ EMT Connector 68 pcs.
3 15 mmΦ EMT Locknut & Bushing 30 pcs.
4 Hangers and Supports 1 lot
5 Utility Box 17 pcs
Wires and Cables
1 RG-6/U Coaxial Cable 90% Braided 2 roll
SUB-TOTAL

Miscellaneous
1 Electrical PVC Tape 5 rolls
2 G.I. Wire gauge 16 4 kgs
3 Hacksaw Blade 4 pcs
4 Assorted Tox, screw, nails, drill bits, etc. 1 lot
SUB-TOTAL

PROPOSED POWER HOUSE


I. EARTHWORKS
1 Excavation 18.00 cu.m.
2 Backfilling 10.50 cu.m.
3 Soil Compaction 7.00 cu.m.
4 3/4" Gravel Bedding 3.00 cu.m.

II. CONCRETE
1 40kg. Portland Cement 300.00 bags
2 Sand 30.00 cu.m.
3 Gravel 33.00 cu.m.

III. REINFORCEMENT
1 16mm.x6mts. 1,228.00 kgs.
2 12mm.x6mts. 1,093.00 pcs.
3 10mm.x6mts. 573.00 pcs.
4 Tie Wire No.16 1.50 roll

IV. FORMWORKS
1 1/2"x4'x8' Ordinary Plywood 33.00 pcs.
2 2"x3"x12' Coco Lumber 120.00 pcs.
3 1 1/2" Common Nail 8.00 kgs.
4 3" Common Nail 15.00 kgs.
5 4" Common Nail 22.00 kgs.

V. MASONRY
1 6" CHB 1,000.00 pcs.
2 10mm.x6mts. 47.00 pcs.
3 Tie Wire No.16 1.50 roll
4 40kg. Portland Cement 63.00 bags
5 Sand 8.00 cu.m.

ARCHITECTURAL
VI. PAINTING
1 Interior Finish 165.00 sq.mts.
Odour-less and Anti-Bacterial Acrylic Page 16 of 35
Republic of the Philippines
Department of Health

BILL OF QUANTITIES

CONSTRUCTION OF PRESIDENTIAL SECURITY GROUP STATION HOSPITAL PHASE 1


Malacañang Park, Manila
Project Name and Location

Item
DESCRIPTION QTY UNIT UNIT COST TOTAL COST
No.
A. GENERAL REQUIREMENTS
Interior Latex Paint Finish - Plant Mixed
full putty - includes Miscellaneous items

2 Exterior Finish 180.00 sq.mts.


Semi-Gloss Latex Paint Finish (Plan Mixed)
full putty - includes Miscellaneous items

3 Elastomeric Waterproofing Paint 73.50 sq.mts.

VIII. DOORS
1 COMPONENTS : 2.00 set
Metal Door (4 Panels -800mm X 2100mm)
2"X6"x2.0mm. Thick with steel louvers
includes Metal Single Rabbet Jambs
Cylindrical Type Door Knob, Dead Bolt
8-pcs Ball Bearing Hinges
Quick Drying Enamel Finish (Metal) Spray
Applied

IX. PLUMBING
1 PVC Pipe 3"x3mts. Series 1000 7.00 pcs.
2 PVC Pipe 4"x3mts. Series 1000 5.00 pcs.
3 90deg. Elbow, 3" dia. 15.00 pcs.
4 4" Roof Drain (Dome Type) S/S Strainer 4.00 pcs.
5 Area Drain Stainless Cover 300mmx300mm. 4.00 pcs.
6 4"x4" Stainless Floor Drain 2.00 pcs.
7 3" P-Trap PVC 2.00 pcs.
8 400cc Solvent Cement 5.00 cans
9 Hose Bibb 1/2" 1.00 pc.
10 1/2" Gate Valve 1.00 pc.
11 20mm.dia.x4mts. PPR Pipes 2.00 pcs.
12 20mm.dia.x1/2" Male Adapter PPR 3.00 pcs.
13 20mm.dia.x 1/2" Female Elbow PPR 2.00 pcs.

SUB-TOTAL

TOTAL ELECTRICAL AND AUXILLARY WORKS


A PLUMBING FIXTURES (GROUND FLOOR PHASE 1)
A.1 Wc- Tank Type Dual Flush elongated
w/ complete fittings and accessories 6 sets
A.2 Lavatory Semi-Pedestal Type complete w/ spray
faucet, ceramic disk type with fittings and access. 6 sets
A.3 Lavatory Counter Type complete w/ spray
faucet, ceramic disk type with fittings and access. 2 sets
A.4 Wash sink Ga.#16 single compartment with drain board
w/ spray faucet, ceramic disk type with fittings and access. 2 sets
A.5 Urinal - Flush valve type elongated w/ fittings and access. 5 sets
A.6 Face mirror, Lead, Copper and Distortion Free 0.8m x 0.50m
6mm thk, complete with studs/brackets and accessories 8 sets
A.7 Face mirror, Lead, Copper and Distortion Free 0.8m x 1.60m
6mm thk,complete with studs/brackets and accessories 6 sets
A.8 Concealed Floor Drains (Stainless steel) 19 pcs
A.9 Tissue Paper Holder Wall embedded 6 pcs
A.10 Bidet/Spray hose complete w/ fittings stainless steel 6 pcs
A.11 Hose Bibb Faucet Page 17 of 35 1 unit
Republic of the Philippines
Department of Health

BILL OF QUANTITIES

CONSTRUCTION OF PRESIDENTIAL SECURITY GROUP STATION HOSPITAL PHASE 1


Malacañang Park, Manila
Project Name and Location

Item
DESCRIPTION QTY UNIT UNIT COST TOTAL COST
No.
A.A.12
GENERAL REQUIREMENTS
Oil/Grease interceptor 15gals Stainless Steel 2 pcs
Sub Total A

A PLUMBING FIXTURES (GROUND FLOOR PHASE 2)


A.1 Wc- Tank Type Dual Flush elongated
w/ complete fittings and accessories 6 sets
A.2 Lavatory Semi-Pedestal Type complete w/ spray
faucet, ceramic disk type with fittings and access. 9 sets
A.3 Lavatory Counter Type complete w/ spray
faucet, ceramic disk type with fittings and access. 1 sets
A.4 Wash sink Ga.#16 single compartment with drain board
w/ spray faucet, ceramic disk type with fittings and access. 3 sets
A.5 Urinal - Flush valve type elongated w/ fittings and access. 4 sets
A.6 Face mirror, Lead, Copper and Distortion Free 0.8m x 0.50m
6mm thk, complete with studs/brackets and accessories 10 sets
A.7 Concealed Floor Drains (Stainless steel) 28 pcs
A.8 Tissue Paper Holder Wall embedded 6 pcs
A.9 Bidet/Spray hose complete w/ fittings stainless steel 6 pcs
A.10 Oil/Grease interceptor 15gals Stainless Steel 3 pcs
Sub Total A

B SEWER SYSTEM (GROUND FLOOR)


B.1 200mm dia uPVC Extra HD 118 L.m.
B.2 160mm dia uPVC Extra HD 122 L.m.
B.3 110mm dia uPVC Extra HD 246 L.m.
B.4 90mm dia uPVC Extra HD 60 L.m.
B.5 63mm dia uPVC Extra HD 65 L.m.
B.6 200x200mm uPVC Wye 5 pcs
B.7 200x160mm uPVC Wye 2 pcs
B.8 200x110mm uPVC Wye 5 pcs
B.9 160x160mm uPVC Wye 8 pcs
B.10 110x110mm uPVC Wye 53 pcs
B.11 110x90mm uPVC Wye 6 pcs
B.12 110x63mm uPVC Wye 124 pcs
B.13 90x90mm uPVC Wye 4 pcs
B.14 90x63mm uPVC Wye 26 pcs
B.15 63x63mm uPVC Wye 6 pcs
B.16 200mm dia uPVC Elbow 45 3 pcs
B.17 160mm dia uPVC Elbow 45 11 pcs
B.18 110mm dia uPVC Elbow 45 33 pcs
B.19 90mm dia uPVC Elbow 45 14 pcs
B.20 63mm dia uPVC Elbow 45 8 pcs
B.21 200mm dia uPVC Elbow 90 2 pcs
B.22 160mm dia uPVC Elbow 90 2 pcs
B.23 110mm dia uPVC Elbow 90 65 pcs
B.24 90mm dia uPVC Elbow 90 14 pcs
B.25 63mm dia uPVC Elbow 90 76 pcs
B.26 200mm dia Ground Cleanout with encasement 6 pcs
B.27 150mm dia Ground Cleanout with encasement 8 pcs
B.28 100mm dia Floor Cleanout Stainless Steel 33 pcs
B.29 75mm dia Floor Cleanout Stainless Steel 14 pcs
B.30 50mm dia P-trap 60 pcs
B.31 uPVC Solvent Cement 400ml 30 can
Sub Total B

C LABORATORY WASTEWATER SYSTEM (GROUND FLOOR)


C.1 90mm dia HDPE pipe 34 L.m.
C.2 63mm dia HDPE pipe 14 L.m.
C.3 90x90mm HDPE Wye Page 18 of 35 9 pcs
Republic of the Philippines
Department of Health

BILL OF QUANTITIES

CONSTRUCTION OF PRESIDENTIAL SECURITY GROUP STATION HOSPITAL PHASE 1


Malacañang Park, Manila
Project Name and Location

Item
DESCRIPTION QTY UNIT UNIT COST TOTAL COST
No.
A.C.4
GENERAL
90x63mmREQUIREMENTS
HDPE Wye 13 pcs
C.5 63x63mm HDPE Wye 4 pcs
C.6 90mm dia HDPE Elbow 45 5 pcs
C.7 63mm dia HDPE Elbow 45 6 pcs
C.8 90mm dia HDPE Elbow 90 1 pcs
C.9 63mm dia HDPE Elbow 90 7 pcs
Sub Total C

D VENT SYSTEM (GROUND FLOOR)


D.1 90mm dia uPVC Extra HD 89 L.m.
D.2 63mm dia uPVC Extra HD 420 L.m.
D.3 90mm dia uPVC Elbow 90 4 pcs
D.4 63mm dia uPVC Elbow 90DEG 286 pcs
D.5 110x63mm Tee 32 pcs
D.6 90x90mm Tee 2 pcs
D.7 90x63mm Tee 14 pcs
D.8 63x63mm Tee 228 pcs
D.9 90x63mm uPVC Reducer 4 pcs
D.10 Hangers and Brackets 127 pcs
D.11 uPVC Solvent Cement 400ml 35 can
Sub Total D
E POTABLE COLD WATER SYSTEM (GROUND FLOOR PHASE 1)
E.1 63mm dia (PN25) Fusion weld pipe 226 L.m.
E.2 32mm dia (PN25) Fusion weld pipe 4 L.m.
E.3 25mm dia (PN25) Fusion weld pipe 78 L.m.
E.4 20mm dia (PN25) Fusion weld pipe 82 L.m.
E.5 63x63x63mm dia (PN25) Tee 7 pcs
E.6 63x32x63mm dia (PN25) Tee 2 pcs
E.7 63x25x63mm dia (PN25) Tee 7 pcs
E.8 32x20x32mm dia (PN25) Tee 1 pcs
E.9 25x25x25mm dia (PN25) Tee 4 pcs
E.10 25x20x25mm dia (PN25) Tee 9 pcs
E.11 20x20x20mm dia (PN25) Tee 4 pcs
E.12 63mm dia (PN25) Elbow 90DEG 8 pcs
E.13 25mm dia (PN25) Elbow 90DEG 22 pcs
E.14 20mm dia (PN25) Elbow 90DEG 33 pcs
E.15 63x50mm (PN25)Reducer 1 pcs
E.16 63x25mm (PN25)Reducer 1 pcs
E.17 63x20mm (PN25)Reducer 1 pcs
E.18 32x25mm (PN25)Reducer 1 pcs
E.19 25x20mm (PN25)Reducer 10 pcs
E.20 20mm dia (PN25) Hammer arrester 27 pcs
E.21 20mm dia (PN25) Tee Adaptor 31 pcs
E.22 20mm dia (PN25) Elbow Adaptor 4 pcs
E.23 Hangers and Brackets 77 pcs
E.24 Gate valves 63mm (PN25) 2 pcs
E.25 Gate valves 25mm (PN25) 4 pcs
E.26 Gate valves 20mm (PN25) 9 pcs
E.27 Teplon Tapes 31 pcs
Sub Total E

E POTABLE COLD WATER SYSTEM (GROUND FLOOR PHASE 2)


E.1 32mm dia (PN25) Fusion weld pipe 41 L.m.
E.2 25mm dia (PN25) Fusion weld pipe 80 L.m.
E.3 20mm dia (PN25) Fusion weld pipe 115 L.m.
E.4 63x32x63mm dia (PN25) Tee 2 pcs
E.5 63x25x63mm dia (PN25) Tee 1 pcs
E.6 63x20x63mm dia (PN25) Tee 1 pcs
E.7 32x25x32mm dia (PN25) Tee Page 19 of 35 3 pcs
Republic of the Philippines
Department of Health

BILL OF QUANTITIES

CONSTRUCTION OF PRESIDENTIAL SECURITY GROUP STATION HOSPITAL PHASE 1


Malacañang Park, Manila
Project Name and Location

Item
DESCRIPTION QTY UNIT UNIT COST TOTAL COST
No.
A.E.8
GENERAL REQUIREMENTS
32x20x32mm dia (PN25) Tee 4 pcs
E.9 25x25x25mm dia (PN25) Tee 3 pcs
E.10 25x20x25mm dia (PN25) Tee 15 pcs
E.11 20x20x20mm dia (PN25) Tee 6 pcs
E.12 32mm dia (PN25) Elbow 90DEG 3 pcs
E.13 25mm dia (PN25) Elbow 90DEG 24 pcs
E.14 20mm dia (PN25) Elbow 90DEG 42 pcs
E.15 32x25mm (PN25)Reducer 1 pcs
E.16 32x20mm (PN25)Reducer 1 pcs
E.17 25x20mm (PN25)Reducer 9 pcs
E.18 20mm dia (PN25) Hammer arrester 25 pcs
E.19 20mm dia (PN25) Tee Adaptor 30 pcs
E.20 20mm dia (PN25) Elbow Adaptor 5 pcs
E.21 Hangers and Brackets 41 pcs
E.22 Gate valves 25mm (PN25) 6 pcs
E.23 Gate valves 20mm (PN25) 13 pcs
E.24 Teplon Tapes 30 pcs
Sub Total E

E POTABLE COLD WATER SYSTEM (GROUND FLOOR PHASE 3)


E.1 50mm dia (PN25) Fusion weld pipe 100 L.m.
E.2 25mm dia (PN25) Fusion weld pipe 78 L.m.
E.3 20mm dia (PN25) Fusion weld pipe 194 L.m.
E.4 63x63x63mm dia (PN25) Tee 1 pcs
E.5 63x32x63mm dia (PN25) Tee 1 pcs
E.6 63x25x63mm dia (PN25) Tee 6 pcs
E.7 63x20x63mm dia (PN25) Tee 8 pcs
E.8 32x25x32mm dia (PN25) Tee 4 pcs
E.9 32x20x32mm dia (PN25) Tee 4 pcs
E.10 25x20x25mm dia (PN25) Tee 5 pcs
E.11 20x20x20mm dia (PN25) Tee 19 pcs
E.12 32mm dia (PN25) Elbow 90DEG 2 pcs
E.13 25mm dia (PN25) Elbow 90DEG 13 pcs
E.14 20mm dia (PN25) Elbow 90DEG 89 pcs
E.15 32x25mm (PN25)Reducer 2 pcs
E.16 25x20mm (PN25)Reducer 8 pcs
E.17 20mm dia (PN25) Hammer arrester 47 pcs
E.18 20mm dia (PN25) Tee Adaptor 47 pcs
E.19 Hangers and Brackets 93 pcs
E.20 Gate valves 25mm (PN25) 4 pcs
E.21 Gate valves 20mm (PN25) 26 pcs
E.22 Teplon Tapes 47 pcs
Sub Total E
F NON POTABLE WATER SYSTEM ( FOR WATER CLOSET AND URINAL) (GROUND FLOOR PHASE 1)
F.1 50mm dia (PN25) Fusion weld pipe 260 L.m.
F.2 32mm dia (PN25) Fusion weld pipe 4 L.m.
F.3 25mm dia (PN25) Fusion weld pipe 52 L.m.
F.4 20mm dia (PN25) Fusion weld pipe 20 L.m.
F.5 50x50x50mm dia (PN25) Tee 7 pcs
F.6 50x32x50mm dia (PN25) Tee 1 pcs
F.7 50x25x50mm dia (PN25) Tee 2 pcs
F.8 32x25x32mm dia (PN25) Tee 1 pcs
F.9 25x25x25mm dia (PN25) Tee 5 pcs
F.10 50mm dia (PN25) Elbow 90DEG 8 pcs
F.11 25mm dia (PN25) Elbow 90DEG 19 pcs
F.12 20mm dia (PN25) Elbow 90DEG 8 pcs
F.13 50x20mm (PN25)Reducer 2 pcs
F.14 32x25mm (PN25)Reducer 1 pcs
F.15 25x20mm (PN25)Reducer Page 20 of 35 5 pcs
Republic of the Philippines
Department of Health

BILL OF QUANTITIES

CONSTRUCTION OF PRESIDENTIAL SECURITY GROUP STATION HOSPITAL PHASE 1


Malacañang Park, Manila
Project Name and Location

Item
DESCRIPTION QTY UNIT UNIT COST TOTAL COST
No.
A.F.16
GENERAL
25mm diaREQUIREMENTS
(PN25) Hammer arrester 5 pcs
F.17 20mm dia (PN25) Hammer arrester 6 pcs
F.18 25mm dia (PN25) Tee Adaptor 5 pcs
F.19 20mm dia (PN25) Tee Adaptor 6 pcs
F.20 Hangers and Brackets 84 pcs
F.21 Gate valves 50mm (PN25) 2 pcs
F.22 Gate valves 25mm (PN25) 5 pcs
F.23 Gate valves 20mm (PN25) 2 pcs
F.24 Teplon Tapes 5 pcs
Sub Total F

F NON POTABLE WATER SYSTEM ( FOR WATER CLOSET AND URINAL) (GROUND FLOOR PHASE 2)
F.1 25mm dia (PN25) Fusion weld pipe 58 L.m.
F.2 20mm dia (PN25) Fusion weld pipe 18 L.m.
F.3 50x25x50mm dia (PN25) Tee 4 pcs
F.4 25x25x25mm dia (PN25) Tee 5 pcs
F.5 25x20x25mm dia (PN25) Tee 1 pcs
F.6 25mm dia (PN25) Elbow 90DEG 16 pcs
F.7 20mm dia (PN25) Elbow 90DEG 4 pcs
F.8 25x20mm (PN25)Reducer 5 pcs
F.9 25mm dia (PN25) Hammer arrester 4 pcs
F.10 20mm dia (PN25) Hammer arrester 6 pcs
F.11 25mm dia (PN25) Tee Adaptor 4 pcs
F.12 20mm dia (PN25) Tee Adaptor 6 pcs
F.13 Hangers and Brackets 19 pcs
F.14 Gate valves 25mm (PN25) 4 pcs
F.15 Gate valves 20mm (PN25) 2 pcs
F.16 Teplon Tapes 4 pcs
Sub Total F

F NON POTABLE WATER SYSTEM ( FOR WATER CLOSET AND URINAL) (GROUND FLOOR PHASE 3)
F.1 50mm dia (PN25) Fusion weld pipe 100 L.m.
F.2 32mm dia (PN25) Fusion weld pipe 10 L.m.
F.3 25mm dia (PN25) Fusion weld pipe 112 L.m.
F.4 20mm dia (PN25) Fusion weld pipe 58 L.m.
F.5 50x50x50mm dia (PN25) Tee 2 pcs
F.6 50x32x50mm dia (PN25) Tee 1 pcs
F.7 50x25x50mm dia (PN25) Tee 5 pcs
F.8 32x25x32mm dia (PN25) Tee 2 pcs
F.9 25x20x25mm dia (PN25) Tee 6 pcs
F.10 20x20x20mm dia (PN25) Tee 4 pcs
F.11 50mm dia (PN25) Elbow 90DEG 3 pcs
F.12 32mm dia (PN25) Elbow 90DEG 2 pcs
F.13 25mm dia (PN25) Elbow 90DEG 37 pcs
F.14 20mm dia (PN25) Elbow 90DEG 24 pcs
F.15 50x32mm (PN25)Reducer 1 pcs
F.16 25x20mm (PN25)Reducer 5 pcs
F.17 25mm dia (PN25) Hammer arrester 16 pcs
F.18 20mm dia (PN25) Hammer arrester 20 pcs
F.19 25mm dia (PN25) Tee Adaptor 16 pcs
F.20 20mm dia (PN25) Tee Adaptor 20 pcs
F.21 Hangers and Brackets 70 pcs
F.22 Gate valves 25mm (PN25) 10 pcs
F.23 Gate valves 20mm (PN25) 8 pcs
F.24 Teplon Tapes 16 pcs
Sub Total F

G AIRCON DRAIN (GROUND & SECOND FLOOR PHASE 1)


G.1 90mm dia pipe (HDPE) Page 21 of 35 205 L.m.
Republic of the Philippines
Department of Health

BILL OF QUANTITIES

CONSTRUCTION OF PRESIDENTIAL SECURITY GROUP STATION HOSPITAL PHASE 1


Malacañang Park, Manila
Project Name and Location

Item
DESCRIPTION QTY UNIT UNIT COST TOTAL COST
No.
A.G.2
GENERAL
32mm diaREQUIREMENTS
pipe (HDPE) 180 L.m.
G.3 90x32mm Wye 71 pcs
G.4 32mm Elbow 90DEG 142 pcs
G.5 32mm Elbow 45DEG 142 pcs
G.6 Floor Clean out 4 pcs
G.7 Hangers and Brackets 96 pcs
Sub Total G

G AIRCON DRAIN (GROUND & SECOND FLOOR PHASE 2)


G.1 90mm dia pipe (HDPE) 126 L.m.
G.2 32mm dia pipe (HDPE) 120 L.m.
G.3 90x32mm Wye 46 pcs
G.4 32mm Elbow 90DEG 92 pcs
G.5 32mm Elbow 45DEG 92 pcs
G.6 Floor Clean out 4 pcs
G.7 Hangers and Brackets 62 pcs
Sub Total G

G AIRCON DRAIN (GROUND & SECOND FLOOR PHASE 3)


G.1 90mm dia pipe (HDPE) 233 L.m.
G.2 32mm dia pipe (HDPE) 170 L.m.
G.3 90x32mm Wye 65 pcs
G.4 32mm Elbow 90DEG 130 pcs
G.5 32mm Elbow 45DEG 130 pcs
G.6 Floor Clean out 4 pcs
G.7 Hangers and Brackets 101 pcs
Sub Total G

A PLUMBING FIXTURES (SECOND FLOOR PHASE 1)


A.1 Wc- Tank Type Dual Flush elongated
w/ complete fittings and accessories 8 sets
A.2 Lavatory Semi-Pedestal Type complete w/ spray
faucet, ceramic disk type with fittings and access. 5 sets
A.3 Lavatory Counter Type complete w/ spray
faucet, ceramic disk type with fittings and access. 4 sets
A.4 Wash sink Ga.#16 single compartment with drain board
w/ spray faucet, ceramic disk type with fittings and access. 1 sets
A.5 Wash sink Ga.#16 double compartment with drain board
w/ dual spray faucet, ceramic disk type with fittings and access. 1 sets
A.6 Urinal - Flush valve type elongated w/ fittings and access. 5 sets
A.7 Face mirror, Lead, Copper and Distortion Free 0.8m x 0.50m
6mm thk, complete with studs/brackets and accessories 9 sets
A.8 Face mirror, Lead, Copper and Distortion Free 0.8m x 1.00m
6mm thk,complete with studs/brackets and accessories 2 sets
A.9 Face mirror, Lead, Copper and Distortion Free 0.8m x 1.60m
6mm thk,complete with studs/brackets and accessories 6 sets
A.10 Concealed Floor Drains (Stainless steel) 15 pcs
A.11 Tissue Paper Holder Wall embedded 8 pcs
A.12 Shower head, Shower valve and faucet ceramic disk type 1 sets
A.13 Over head shower, hot and cold valve and faucet 1 sets
A.14 Bidet/Spray hose complete w/ fittings stainless steel 8 pcs
A.15 Hot and cold Whirlpool bath tub complete with accessories 1 unit
A.16 Multi point electric water heater 2 unit
A.17 Oil/Grease interceptor 15gals Stainless Steel 2 pcs
Sub Total A

A PLUMBING FIXTURES (SECOND FLOOR PHASE 2)


A.1 Wc- Tank Type Dual Flush elongated Page 22 of 35
Republic of the Philippines
Department of Health

BILL OF QUANTITIES

CONSTRUCTION OF PRESIDENTIAL SECURITY GROUP STATION HOSPITAL PHASE 1


Malacañang Park, Manila
Project Name and Location

Item
DESCRIPTION QTY UNIT UNIT COST TOTAL COST
No.
A. GENERAL REQUIREMENTS
w/ complete fittings and accessories 11 sets
A.2 Lavatory Semi-Pedestal Type complete w/ spray
faucet, ceramic disk type with fittings and access. 6 sets
A.3 Lavatory Counter Type complete w/ spray
faucet, ceramic disk type with fittings and access. 5 sets
A.4 Wash sink Ga.#16 single compartment with drain board
w/ spray faucet, ceramic disk type with fittings and access. 5 sets
A.5 Urinal - Flush valve type elongated w/ fittings and access. 3 sets
A.6 Face mirror, Lead, Copper and Distortion Free 0.8m x 0.50m
6mm thk, complete with studs/brackets and accessories 10 sets
A.7 Concealed Floor Drains (Stainless steel) 24 pcs
A.8 Tissue Paper Holder Wall embedded 11 pcs
A.9 Shower head, Shower valve and faucet ceramic disk type 5 sets
A.10 Bidet/Spray hose complete w/ fittings stainless steel 11 pcs
A.11 Hose Bibb Faucet 2 pcs
A.12 Oil/Grease interceptor 15gals Stainless Steel 3 pcs
Sub Total A

B SEWER SYSTEM (SECOND FLOOR)


B.1 160mm dia uPVC Extra HD 102 L.m.
B.2 110mm dia uPVC Extra HD 226 L.m.
B.3 63mm dia uPVC Extra HD 136 L.m.
B.4 160x160mm uPVC Wye 10 pcs
B.5 160x110mm uPVC Wye 26 pcs
B.6 110x110mm uPVC Wye 45 pcs
B.7 110x63mm uPVC Wye 128 pcs
B.8 63x63mm uPVC Wye 31 pcs
B.9 160mm dia uPVC Elbow 45 10 pcs
B.10 110mm dia uPVC Elbow 45 44 pcs
B.11 63mm dia uPVC Elbow 45 18 pcs
B.12 160mm dia uPVC Elbow 90 6 pcs
B.13 110mm dia uPVC Elbow 90 560 pcs
B.14 63mm dia uPVC Elbow 90 80 pcs
B.15 150mm dia Floor Cleanout Stainless Steel 10 pcs
B.16 100mm dia Floor Cleanout Stainless Steel 28 pcs
B.17 50mm dia Floor Cleanout Stainless Steel 9 pcs
B.18 50mm dia P-trap 82 pcs
B.19 uPVC Solvent Cement 400ml 52 can
Sub Total B

C VENT SYSTEM (GROUND FLOOR)


C.1 90mm dia uPVC Extra HD 20 L.m.
C.2 63mm dia uPVC Extra HD 433 L.m.
C.3 90mm dia uPVC Elbow 90 2 pcs
C.4 63mm dia uPVC Elbow 90DEG 33 pcs
C.5 110x63mm Tee 33 pcs
C.6 90x90mm Tee 6 pcs
C.7 90x63mm Tee 12 pcs
C.8 63x63mm Tee 166 pcs
C.9 90x63mm uPVC Reducer 5 pcs
C.10 Hangers and Brackets 127 pcs
C.11 uPVC Solvent Cement 400ml 35 can
Sub Total C

E POTABLE COLD WATER SYSTEM (SECOND FLOOR PHASE 1)


E.1 63mm dia (PN25) Fusion weld pipe 178 L.m.
E.2 50mm dia (PN25) Fusion weld pipe 20 L.m.
E.3 40mm dia (PN25) Fusion weld pipe 6 L.m.
E.5 25mm dia (PN25) Fusion weld pipe Page 23 of 35 30 L.m.
Republic of the Philippines
Department of Health

BILL OF QUANTITIES

CONSTRUCTION OF PRESIDENTIAL SECURITY GROUP STATION HOSPITAL PHASE 1


Malacañang Park, Manila
Project Name and Location

Item
DESCRIPTION QTY UNIT UNIT COST TOTAL COST
No.
A.E.6
GENERAL
20mm diaREQUIREMENTS
(PN25) Fusion weld pipe 46 L.m.
E.7 63x63x63mm dia (PN25) Tee 7 pcs
E.10 63x25x63mm dia (PN25) Tee 1 pcs
E.11 63x20x63mm dia (PN25) Tee 1 pcs
E.7 50x50x50mm dia (PN25) Tee 1 pcs
E.10 50x25x50mm dia (PN25) Tee 2 pcs
E.11 50x20x50mm dia (PN25) Tee 1 pcs
E.14 40x20x40mm dia (PN25) Tee 1 pcs
E.18 25x20x25mm dia (PN25) Tee 7 pcs
E.19 20x20x20mm dia (PN25) Tee 6 pcs
E.20 63mm dia (PN25) Elbow 90DEG 11 pcs
E.21 50mm dia (PN25) Elbow 90DEG 2 pcs
E.24 25mm dia (PN25) Elbow 90DEG 27 pcs
E.25 20mm dia (PN25) Elbow 90DEG 30 pcs
E.26 63x50mm (PN25)Reducer 1 pcs
E.27 50x25mm (PN25)Reducer 2 pcs
E.32 25x20mm (PN25)Reducer 13 pcs
E.33 20mm dia (PN25) Hammer arrester 22 pcs
E.34 20mm dia (PN25) Tee Adaptor 25 pcs
E.35 20mm dia (PN25) Elbow Adaptor 3 pcs
E.36 Hangers and Brackets 70 pcs
E.37 Gate valves 63mm (PN25) 2 pcs
E.40 Gate valves 25mm (PN25) 4 pcs
E.41 Gate valves 20mm (PN25) 8 pcs
E.42 Teplon Tapes 25 pcs
Sub Total E

E POTABLE COLD WATER SYSTEM (SECONDFLOOR PHASE 2)


E.1 25mm dia (PN25) Fusion weld pipe 72 L.m.
E.6 20mm dia (PN25) Fusion weld pipe 94 L.m.
E.10 63x25x63mm dia (PN25) Tee 7 pcs
E.11 63x20x63mm dia (PN25) Tee 4 pcs
E.18 25x20x25mm dia (PN25) Tee 14 pcs
E.19 20x20x20mm dia (PN25) Tee 6 pcs
E.24 25mm dia (PN25) Elbow 90DEG 30 pcs
E.25 20mm dia (PN25) Elbow 90DEG 34 pcs
E.32 25x20mm (PN25)Reducer 9 pcs
E.33 20mm dia (PN25) Hammer arrester 29 pcs
E.34 20mm dia (PN25) Tee Adaptor 34 pcs
E.35 20mm dia (PN25) Elbow Adaptor 5 pcs
E.36 Hangers and Brackets 42 pcs
E.40 Gate valves 25mm (PN25) 6 pcs
E.41 Gate valves 20mm (PN25) 11 pcs
E.42 Teplon Tapes 34 pcs
Sub Total E

E POTABLE COLD WATER SYSTEM (SECOND FLOOR PHASE 3)


E.1 63mm dia (PN25) Fusion weld pipe 122 L.m.
E.4 32mm dia (PN25) Fusion weld pipe 54 L.m.
E.5 25mm dia (PN25) Fusion weld pipe 88 L.m.
E.6 20mm dia (PN25) Fusion weld pipe 246 L.m.
E.9 63x32x63mm dia (PN25) Tee 1 pcs
E.10 63x25x63mm dia (PN25) Tee 9 pcs
E.11 63x20x63mm dia (PN25) Tee 9 pcs
E.16 32x25x32mm dia (PN25) Tee 1 pcs
E.17 32x20x32mm dia (PN25) Tee 2 pcs
E.18 25x25x25mm dia (PN25) Tee 2 pcs
E.18 25x20x25mm dia (PN25) Tee 20 pcs
E.19 20x20x20mm dia (PN25) Tee Page 24 of 35 10 pcs
Republic of the Philippines
Department of Health

BILL OF QUANTITIES

CONSTRUCTION OF PRESIDENTIAL SECURITY GROUP STATION HOSPITAL PHASE 1


Malacañang Park, Manila
Project Name and Location

Item
DESCRIPTION QTY UNIT UNIT COST TOTAL COST
No.
A.E.23
GENERAL
32mm diaREQUIREMENTS
(PN25) Elbow 90DEG 1 pcs
E.24 25mm dia (PN25) Elbow 90DEG 41 pcs
E.25 20mm dia (PN25) Elbow 90DEG 80 pcs
E.31 32x20mm (PN25)Reducer 1 pcs
E.32 25x20mm (PN25)Reducer 12 pcs
E.33 20mm dia (PN25) Hammer arrester 49 pcs
E.34 20mm dia (PN25) Tee Adaptor 55 pcs
E.35 20mm dia (PN25) Elbow Adaptor 6 pcs
E.36 Hangers and Brackets 128 pcs
E.40 Gate valves 25mm (PN25) 6 pcs
E.41 Gate valves 20mm (PN25) 25 pcs
E.42 Teplon Tapes 55 pcs
Sub Total E

F NON POTABLE WATER SYSTEM ( FOR WATER CLOSET AND URINAL) (SECOND FLOOR PHASE 1)
F.1 50mm dia (PN25) Fusion weld pipe 178 L.m.
F.3 40mm dia (PN25) Fusion weld pipe 26 L.m.
F.5 25mm dia (PN25) Fusion weld pipe 49 L.m.
F.6 20mm dia (PN25) Fusion weld pipe 24 L.m.
F.12 50x50x50mm dia (PN25) Tee 7 pcs
F.13 50x40x50mm dia (PN25) Tee 1 pcs
F.15 50x25x50mm dia (PN25) Tee 2 pcs
F.16 50x20x50mm dia (PN25) Tee 2 pcs
F.19 40x20x40mm dia (PN25) Tee 1 pcs
F.23 25x25x25mm dia (PN25) Tee 3 pcs
F.25 20x20x20mm dia (PN25) Tee 2 pcs
F.27 50mm dia (PN25) Elbow 90DEG 11 pcs
F.28 40mm dia (PN25) Elbow 90DEG 2 pcs
F.30 25mm dia (PN25) Elbow 90DEG 19 pcs
F.31 20mm dia (PN25) Elbow 90DEG 11 pcs
F.35 50x40mm (PN25)Reducer 1 pcs
F.35 50x20mm (PN25)Reducer 1 pcs
F.39 32x25mm (PN25)Reducer 1 pcs
F.41 25x20mm (PN25)Reducer 5 pcs
F.42 25mm dia (PN25) Hammer arrester 5 pcs
F.42 20mm dia (PN25) Hammer arrester 8 pcs
F.43 25mm dia (PN25) Tee Adaptor 5 pcs
F.43 20mm dia (PN25) Tee Adaptor 8 pcs
F.45 Hangers and Brackets 70 pcs
F.47 Gate valves 50mm (PN25) 2 pcs
F.50 Gate valves 25mm (PN25) 5 pcs
F.51 Gate valves 20mm (PN25) 3 pcs
F.52 Teplon Tapes 5 pcs
Sub Total F

F NON POTABLE WATER SYSTEM ( FOR WATER CLOSET AND URINAL) (SECOND FLOOR PHASE 2)
F.1 25mm dia (PN25) Fusion weld pipe 13 L.m.
F.2 20mm dia (PN25) Fusion weld pipe 24 L.m.
F.3 50x25x50mm dia (PN25) Tee 3 pcs
F.4 50x20x50mm dia (PN25) Tee 7 pcs
F.5 25x25x25mm dia (PN25) Tee 2 pcs
F.6 20x20x20mm dia (PN25) Tee 2 pcs
F.7 25mm dia (PN25) Elbow 90DEG 8 pcs
F.8 20mm dia (PN25) Elbow 90DEG 27 pcs
F.9 25x20mm (PN25)Reducer 2 pcs
F.10 25mm dia (PN25) Hammer arrester 3 pcs
F.11 20mm dia (PN25) Hammer arrester 11 pcs
F.12 25mm dia (PN25) Tee Adaptor 3 pcs
F.13 20mm dia (PN25) Tee Adaptor Page 25 of 35 11 pcs
Republic of the Philippines
Department of Health

BILL OF QUANTITIES

CONSTRUCTION OF PRESIDENTIAL SECURITY GROUP STATION HOSPITAL PHASE 1


Malacañang Park, Manila
Project Name and Location

Item
DESCRIPTION QTY UNIT UNIT COST TOTAL COST
No.
A.F.14
GENERAL
Hangers REQUIREMENTS
and Brackets 19 pcs
F.15 Gate valves 25mm (PN25) 5 pcs
F.16 Gate valves 20mm (PN25) 3 pcs
F.17 Teplon Tapes 3 pcs
Sub Total F

F NON POTABLE WATER SYSTEM ( FOR WATER CLOSET AND URINAL) (SECOND FLOOR PHASE 3)
F.1 32mm dia (PN25) Fusion weld pipe 4 L.m.
F.5 25mm dia (PN25) Fusion weld pipe 12 L.m.
F.6 20mm dia (PN25) Fusion weld pipe 42 L.m.
F.14 50x32x50mm dia (PN25) Tee 1 pcs
F.15 50x25x50mm dia (PN25) Tee 2 pcs
F.16 50x20x50mm dia (PN25) Tee 6 pcs
F.21 32x25x32mm dia (PN25) Tee 1 pcs
F.22 32x20x32mm dia (PN25) Tee 1 pcs
F.23 25x25x25mm dia (PN25) Tee 2 pcs
F.24 25x20x25mm dia (PN25) Tee 2 pcs
F.25 20x20x20mm dia (PN25) Tee 3 pcs
F.29 32mm dia (PN25) Elbow 90DEG 1 pcs
F.30 25mm dia (PN25) Elbow 90DEG 10 pcs
F.31 20mm dia (PN25) Elbow 90DEG 36 pcs
F.40 32x20mm (PN25)Reducer 1 pcs
F.42 25mm dia (PN25) Hammer arrester 5 pcs
F.42 20mm dia (PN25) Hammer arrester 14 pcs
F.43 25mm dia (PN25) Tee Adaptor 5 pcs
F.43 20mm dia (PN25) Tee Adaptor 14 pcs
F.45 Hangers and Brackets 70 pcs
F.50 Gate valves 25mm (PN25) 3 pcs
F.51 Gate valves 20mm (PN25) 10 pcs
F.52 Teplon Tapes 5 pcs
Sub Total F
A PLUMBING FIXTURES (ROOF)
A.1 Wc- Tank Type Dual Flush elongated
w/ complete fittings and accessories 3 sets
A.2 Lavatory Counter Type complete w/ spray
faucet, ceramic disk type with fittings and access. 2 sets
A.3 Urinal - Flush valve type elongated w/ fittings and access. 2 sets
A.4 Face mirror, Lead, Copper and Distortion Free 0.8m x 0.50m
6mm thk, complete with studs/brackets and accessories 2 sets
A.5 Concealed Floor Drains (Stainless steel) 6 pcs
A.6 Tissue Paper Holder Wall embedded 3 pcs
A.7 Bidet/Spray hose complete w/ fittings stainless steel 3 pcs
A.8 Hose Bibb Faucet 1 pcs
Sub Total A

B SEWER SYSTEM (ROOF)


B.1 110mm dia uPVC Extra HD 26 L.m.
B.2 63mm dia uPVC Extra HD 4 L.m.
B.3 110x110mm uPVC Wye 6 pcs
B.4 110x63mm uPVC Wye 9 pcs
B.5 110mm dia uPVC Elbow 45 3 pcs
B.6 63mm dia uPVC Elbow 45 4 pcs
B.7 110mm dia uPVC Elbow 90 5 pcs
B.8 63mm dia uPVC Elbow 90 4 pcs
B.9 100mm dia Floor Cleanout Stainless Steel 3 pcs
B.10 50mm dia P-trap 6 pcs
B.11 uPVC Solvent Cement 400ml 2 can
Sub Total B
Page 26 of 35
Republic of the Philippines
Department of Health

BILL OF QUANTITIES

CONSTRUCTION OF PRESIDENTIAL SECURITY GROUP STATION HOSPITAL PHASE 1


Malacañang Park, Manila
Project Name and Location

Item
DESCRIPTION QTY UNIT UNIT COST TOTAL COST
No.
A. CGENERAL REQUIREMENTS
VENT SYSTEM (ROOF)
C.1 90mm dia uPVC Extra HD 12 L.m.
C.2 63mm dia uPVC Extra HD 16 L.m.
C.3 63mm dia uPVC Elbow 90DEG 15 pcs
C.4 110x63mm Tee 3 pcs
C.5 63x63mm Tee 10 pcs
C.6 Vent Cap stainless 4 pcs
C.7 Hangers and Brackets 8 pcs
C.8 uPVC Solvent Cement 400ml 2 can
Sub Total C

E POTABLE COLD WATER SYSTEM (ROOF)


E.1 32mm dia (PN25) Fusion weld pipe 12 L.m.
E.5 25mm dia (PN25) Fusion weld pipe 16 L.m.
E.6 20mm dia (PN25) Fusion weld pipe 4 L.m.
E.12 40x40x40mm dia (PN25) Tee 1 pcs
E.14 40x20x40mm dia (PN25) Tee 1 pcs
E.16 32x25x32mm dia (PN25) Tee 1 pcs
E.18 25x25x25mm dia (PN25) Tee 1 pcs
E.18 25x20x25mm dia (PN25) Tee 2 pcs
E.22 40mm dia (PN25) Elbow 90DEG 1 pcs
E.23 32mm dia (PN25) Elbow 90DEG 2 pcs
E.24 25mm dia (PN25) Elbow 90DEG 5 pcs
E.25 20mm dia (PN25) Elbow 90DEG 2 pcs
E.30 40x20mm (PN25)Reducer 1 pcs
E.31 32x25mm (PN25)Reducer 1 pcs
E.32 25x20mm (PN25)Reducer 3 pcs
E.33 20mm dia (PN25) Hammer arrester 5 pcs
E.34 20mm dia (PN25) Tee Adaptor 5 pcs
E.36 Hangers and Brackets 4 pcs
E.40 Gate valves 25mm (PN25) 2 pcs
E.41 Gate valves 20mm (PN25) 1 pcs
E.42 Teplon Tapes 5 pcs
Sub Total E

F NON POTABLE WATER SYSTEM ( FOR WATER CLOSET AND URINAL) (ROOF)
F.1 32mm dia (PN25) Fusion weld pipe 12 L.m.
F.5 25mm dia (PN25) Fusion weld pipe 14 L.m.
F.6 20mm dia (PN25) Fusion weld pipe 4 L.m.
F.17 40x40x40mm dia (PN25) Tee 1 pcs
F.21 32x25x32mm dia (PN25) Tee 1 pcs
F.23 25x25x25mm dia (PN25) Tee 1 pcs
F.24 25x20x25mm dia (PN25) Tee 2 pcs
F.28 40mm dia (PN25) Elbow 90DEG 1 pcs
F.29 32mm dia (PN25) Elbow 90DEG 2 pcs
F.30 25mm dia (PN25) Elbow 90DEG 3 pcs
F.36 40x32mm (PN25)Reducer 1 pcs
F.39 32x25mm (PN25)Reducer 1 pcs
F.41 25x20mm (PN25)Reducer 3 pcs
F.42 25mm dia (PN25) Hammer arrester 2 pcs
F.42 20mm dia (PN25) Hammer arrester 3 pcs
F.43 25mm dia (PN25) Tee Adaptor 2 pcs
F.43 20mm dia (PN25) Tee Adaptor 3 pcs
F.45 Hangers and Brackets 4 pcs
F.50 Gate valves 25mm (PN25) 2 pcs
F.52 Teplon Tapes 2 pcs
Sub Total F

Page 27 of 35
Republic of the Philippines
Department of Health

BILL OF QUANTITIES

CONSTRUCTION OF PRESIDENTIAL SECURITY GROUP STATION HOSPITAL PHASE 1


Malacañang Park, Manila
Project Name and Location

Item
DESCRIPTION QTY UNIT UNIT COST TOTAL COST
No.
A. GGENERAL REQUIREMENTS
STORM DRAINAGE SYSTEM
G.1 110mm dia uPVC Extra HD 370 L.m.
G.2 63mm dia uPVC Extra HD 105 L.m.
G.3 110x63mm uPVC Wye 76 pcs
G.4 63x63mm uPVC Wye 4 pcs
G.5 63mm dia uPVC Elbow 45 79 pcs
G.6 110mm dia uPVC Elbow 90 41 pcs
G.7 63mm dia uPVC Elbow 90 79 pcs
G.8 uPVC Solvent Cement 400ml 20 can
G.9 200mm dia. Concrete pipe 88 L.m.
G.10 300mm dia. Concrete pipe 108 L.m.
G.11 400mm dia. Concrete pipe 40 L.m.
G.12 Catch Basin/Area Drain 41 units
G.13 Concealed Floor Drains (Stainless steel) 38 pcs
G.14 Gutter Drain/ledge drain dome type stainless 4" 41 pcs
G.15 Gutter Drain/ledge drain dome type stainless 2" 41 pcs
Sub Total G
H POTABLE WATER CISTERN
H.1 excavation and dewatering 38.00 cu.m.
H.2 backfill and compaction 19.00 cu.m.
H.3 excess fill disposal/hauling 20.00 cu.m.
H.4 ready mixed concrete 3500PSI 19.90 cu.m.
Concrete and rebar works
H.5 20mm dia RSB 1,598.40 kgs.
H.6 16mm dia RSB 2,979.90 kgs.
H.7 12mm dia RSB 1,598.40 kgs.
H.8 10mm dia RSB 518.00 kgs.
H.9 crushed gravel 14.00 cu. m.
H.10 non-toxic water proofing 79.00 sq. m.
H.11 polyethylene sheet 20.00 sq. m.
H.12 ga. 16 tie wire 200.00 kgs.
H.13 concrete pavement 2.20 cu.m.
H.14 ladder rung, stainless steel 1.00 pieces
H.15 manhole cover, 6mm thick MS plate 2.00 pieces
form works, scaffoldings
H.16 1/2" x 4' x 8' form plywood 30.00 pieces
H.17 2" x 4" form lumber 1,700.00 bd.ft.
H.18 2" x 3" form lumber 2,000.00 bd.ft.
H.19 4" x 4" form lumber 2,500.00 bd.ft.
H.20 tiewire 150.00 kgs.
H.21 assorted nails 100.00 kgs.
Masonry works
H.22 portland cement 75.00 bags
H.23 sand 20.00 cu. m.
H.24 crushed gravel 7.00 cu. m.
H.25 6" CHB 1,500.00 pieces
H.26 20mm dia x 6m RSB 300.00 kgs
H.27 12mm dia x 6m RSB 500.00 kgs
H.28 10mm dia x 6m RSB 200.00 kgs
H.29 ga. 16 tiewire 50.00 kgs
H.30 steel ladder, caged, mild steel 1.00 set
H.31 W-1, steel louver window 4.00 pieces
H.32 D-1, steel louver door 1.00 pieces
H.33 insect screen 16.00 sq m
SUB-TOTAL H

I POTABLE WATER SYSTEM


I.1 63mm dia (PN25) Fusion weld pipe 110 L.m.
I.2 63x63x63mm dia (PN25) Tee Page 28 of 35 14 pcs
Republic of the Philippines
Department of Health

BILL OF QUANTITIES

CONSTRUCTION OF PRESIDENTIAL SECURITY GROUP STATION HOSPITAL PHASE 1


Malacañang Park, Manila
Project Name and Location

Item
DESCRIPTION QTY UNIT UNIT COST TOTAL COST
No.
A.I.3
GENERAL
63mm diaREQUIREMENTS
(PN25) Elbow 90DEG 24 pcs
I.4 Hangers and Brackets 30 pcs
I.5 Gate valve brnze 50mm dia 11 pcs
I.6 Check valve bronze 50mm dia 3 pcs
I.7 Foot valve 50mm dia brass 2 pcs
I.8 Float valve 50mm dia brass 2 pcs
I.9 Centrifugal Pump 3Hp, 3Ph 2 set
I.10 Level Electrode 2 set
I.11 Wires and conduit 84 Lm
I.12 Duplex controller w/ circuit breaker,magnetic contactor 2 units
voltage relay, alternating relay, enclosure & etc
I.13 5000 Gals Stainless Steel Storage tank 6mm thk w/ acc 2 set
I.14 225 Gals CapacityBladder Tank 1 set
I.15 Jet/Booster pump 1.5Hp Heavy Duty 2 set
SUB-TOTAL I

J NON POTABLE WATER SYSTEM (RAINWATER)


J.1 63mm dia (PN25) Fusion weld pipe 110 L.m.
J.2 63x63x63mm dia (PN25) Tee 14 pcs
J.3 63mm dia (PN25) Elbow 90DEG 24 pcs
J.4 Hangers and Brackets 30 pcs
J.5 Gate valve brnze 50mm dia 11 pcs
J.6 Check valve bronze 50mm dia 3 pcs
J.7 Foot valve 50mm dia brass 2 pcs
J.8 Float valve 50mm dia brass 2 pcs
J.9 Centrifugal Pump 3Hp, 3Ph 2 set
J.10 Level Electrode 2 set
J.11 Wires and conduit 84 Lm
J.12 Duplex controller w/ circuit breaker,magnetic contactor 2 units
voltage relay, alternating relay, enclosure & etc
J.13 5000 Gals Stainless Steel Storage tank 6mm thk w/ acc 2 set
J.14 225 Gals CapacityBladder Tank 1 set
J.15 Jet/Booster pump 1.5Hp Heavy Duty 2 set
SUB-TOTAL J

K RAINWATER STORAGE 2.00 SETS


K.1 4969 Gals Stainless Steel Storage tank 6mm thk w/ acc 1.00 set
K.2 Self Cleaning Vortex Fine Filter for 100sqm 1.00 set
K.3 Concrete Slab Foundation 3500PSI 2.80 cu.m.
K.4 12mm dia Rebar 70.00 KG
K.5 Gravel Bedding 1.80 cu.m.
K.6 110mm dia uPVC Extra HD 10 L.m.
K.7 Tee 100mm dia uPVC 2.00 pcs
K.8 Elbow 100mm dia uPVC 2.00 pcs
K.9 Drainage Non Return Valve/Flush Valve 1.00 pc
K.10 2in dia PE overflow pipe 15.00 L.m.
K.11 Check Valve Bronze Body 2in dia 3.00 pcs
K.12 Gate Valve Bronze body 2in dia 2.00 pcs
K.13 Ball Valve Bronze body 1/2in dia 1.00 pc
K.14 Float Valve 1.00 pc
K.15 Wash Gravel 1.00 cu.m.
K.16 Wash Sand 1.00 cu.m.

Steel Frame/Stand
K.17 3"x3"x1/4" Angular Bar 22.00 L.m
K.18 2"x2"x1/4" Angular Bar 24.00 L.m
K.19 Steel Plate 6mm 1.00 pc
K.20 Concrete Pedestal (Cement Finished) 0.50 cu.m.
K.21 12mm dia Rebar Page 29 of 35 16.00 kg
Republic of the Philippines
Department of Health

BILL OF QUANTITIES

CONSTRUCTION OF PRESIDENTIAL SECURITY GROUP STATION HOSPITAL PHASE 1


Malacañang Park, Manila
Project Name and Location

Item
DESCRIPTION QTY UNIT UNIT COST TOTAL COST
No.
A.K.22
GENERAL REQUIREMENTS
Anchor bolts 16mm dia 16.00 pcs
SUB-TOTAL K

L OTHER
L.1 Excavation 59 cu.m
L.2 Backfilling 44.25 cu.m
L.3 Concrete breaking 24 cu.m
SUB-TOTAL L

SEWAGE TREATMENT PLANT


A CIVIL WORKS
A.1 Excavation 120 cu.m
A.2 Bacfilling 56 cu.m
A.3 Concrete 3500PSI 45 cu.m
A.4 Coarse Aggregates 4 cu.m
A.5 Rebars 16mm dia 3120.48 Kg
A.6 Rebars 12mm dia 554.112 Kg
A.7 Rebars 10mm dia 1116.192 Kg
A.8 GI Tie wire 55 Kg
A.9 Angle bar 2x2x1/4" 6 pcs
A.10 Formworks 180 sq.m.
A.11 Scaffoldings 3541.5 bd.ft.
A.12 Cement 105 bags
A.13 Sand 6 cu.m.
A.14 Miscellaneous 1 lot
Housing
A.15 Excavation 6 cu.m
A.16 Bacfilling 2 cu.m
A.17 Concrete 3500PSI 3 cu.m.
A.18 Rebar 12mm dia 159.84 kg
A.19 Rebars 10mm dia 258.72 Kg
A.20 GI Tie wire 6 Kg
A.21 Formworks 30 sq.m.
A.22 Scaffoldings 295 bd.ft.
A.23 Steel Door 1 set
A.24 Louver blocks 1 lot
A.25 CHB 350 pcs
A.26 Cement 50 bags
A.27 Sand 6 cu.m.
A.28 Miscellaneous 1 lot
Sub total

TOTAL SANITARY WORKS


B MECHANICAL WORKS
B.1 Roots type Blower, 2.2Kw, 3phase, 230V 60hz 3 units
complete w/ base, suction silencer with filter
& discharge silencer
B.2 Fine bubble Tube Diffusers 24 pcs
B.3 Submersible pumps 1Hp complete w/ accessories 7 units
and fittings, Stainless steel, w/ float switch
B.4 Metering pump (chlorine) complete w/ check valve, 1 set
foot valve & Hose, 1250 ml/min, 0.2MPA, 1-360SPM,
48 watts, 230V, 60hz, 1-phase, IP65. japan
B.5 Chlorine Mixer, 120RPM,220V,60Hz,1P,japan w/ stirrer 1 set
complete w/ 210 Gals HDPE tank w/ drain & Graduation
B.6 Main air supply pipe BI pipe epoxy painted 1 set
B.7 Air pipe line submerged 1 set
including hardware and accessories Page 30 of 35
Republic of the Philippines
Department of Health

BILL OF QUANTITIES

CONSTRUCTION OF PRESIDENTIAL SECURITY GROUP STATION HOSPITAL PHASE 1


Malacañang Park, Manila
Project Name and Location

Item
DESCRIPTION QTY UNIT UNIT COST TOTAL COST
No.
A.B.8
GENERAL
DecanterREQUIREMENTS 2 pcs
B.9 Butterfly valve 17 pcs
B.10 Check Valve 7 pcs
B.11 Flanges 34 pcs
B.12 Miscellaneous 1 lot
Sub total

C ELECTRICAL WORKS
C.1 MCC Controller complete w/ wires and accessories 1 set
C.2 Lighting including fixtures wires and conduits 1 set
C.3 Supply wires/Main feedr line 22mm dia THWN 375 L.m
C.4 Conduits 32mm dia uPVC 125 L.m
C.5 Concrete Trench 3000PSI 8 cu.m
C.6 Miscellaneous 1 lot
Sub total

D OTHER
D.1 B.I. Railings 1 1/2" x 3/16" 15 pcs
D.2 Angle bar 1 1/2" x 1 1/2" x1/4" 3 pcs
D.3 Flat Bar 1 1/2"x 1/4" 1 pcs
D.4 Concrete cover 3500PSI 0.1 cu.m.
D.5 Water stop 55 Lm
D.6 Manhole cover 5 pcs
D.7 Cementitious Water Proofing 2 Coats 300 sq.m.
D.8 Epoxy Paint 3 Gal
D.9 Elastomeric Paint 110 sq.m.
D.10 Primer 110 sq.m.
D.11 Neutralizer 30 Gal
D.12 Bar screen stainless steel 1 set
D.13 Hauling 30 cum
Sub total

TOTAL SANITARY WORKS

I. MEDICAL GAS AND VACUUM SYSTEM-Grid A-K/5-12


1.1 Pipes, Valves and Fittings
1.1.1 50mmØ x 6M, hard drawn copper tube 5.00 pieces
1.1.2 40mmØ x 6M, hard drawn copper tube 12.00 pieces
1.1.3 30mmØ x 6M, hard drawn copper tube 15.00 pieces
1.1.4 25mmØ x 6M, hard drawn copper tube 17.00 pieces
1.1.5 20mmØ x 6M, hard drawn copper tube 12.00 pieces
1.1.6 15mmØ x 6M, hard drawn copper tube 22.00 pieces
1.1.7 12mmØ x 6M, hard drawn copper tube 32.00 pieces
1.1.8 50mmØ x 90° elbow, wrought copper 10.00 pieces
1.1.9 40mmØ x 90° elbow, wrought copper 20.00 pieces
1.1.10 30mmØ x 90° elbow, wrought copper 25.00 pieces
1.1.11 25mmØ x 90° elbow, wrought copper 35.00 pieces
1.1.12 20mmØ x 90° elbow, wrought copper 25.00 pieces
1.1.13 15mmØ x 90° elbow, wrought copper 41.00 pieces
1.1.14 12mmØ x 90° elbow, wrought copper 75.00 pieces
1.1.15 50mmØ tee, wrought copper 1.00 pieces
1.1.16 40mmØ tee, wrought copper 8.00 pieces
1.1.17 30mmØ tee, wrought copper 25.00 pieces
1.1.18 25mmØ tee, wrought copper 38.00 pieces
1.1.19 20mmØ tee, wrought copper 55.00 pieces
1.1.20 15mmØ tee, wrought copper 40.00 pieces
1.1.21 12mmØ tee, wrought copper 68.00 pieces
1.1.22 40 x 30mmØ reducer, wrought copper 6.00 pieces
1.1.23 30 x 15mmØ reducer, wrought copper Page 31 of 35 21.00 pieces
Republic of the Philippines
Department of Health

BILL OF QUANTITIES

CONSTRUCTION OF PRESIDENTIAL SECURITY GROUP STATION HOSPITAL PHASE 1


Malacañang Park, Manila
Project Name and Location

Item
DESCRIPTION QTY UNIT UNIT COST TOTAL COST
No.
A. GENERAL
1.1.24 REQUIREMENTS
25 x 15mmØ reducer, wrought copper 43.00 pieces
1.1.25 20 x 15mmØ reducer, wrought copper 58.00 pieces
1.1.26 14 x 12mmØ reducer, wrought copper 89.00 pieces
1.1.27 38 x 30mmØ, tee reducer wrought copper 25.00 pieces
1.1.28 30 x 15mmØ, tee reducer wrought copper 22.00 pieces
1.1.29 15 x 12mmØ, tee reducer wrought copper 65.00 pieces
1.1.30 electrical works 1.00 lot
1.1.31 40mm dia service valve, ceiling type 2.00 pieces
1.1.31 30mm dia service valve, ceiling type 2.00 pieces
1.1.31 25mm dia service valve, ceiling type 2.00 pieces
1.1.32 15mm dia service valve, ceiling type 8.00 pieces
1.1.33 6mm x 25mm flat bar, MS 12.00 pieces
1.1.34 6mm x 30mm x 30mm angle bar, MS 8.00 pieces
1.1.35 38mm dia. U bolt with nut and washer 125.00 pieces
1.1.36 30mm dia. U bolt with nut and washer 130.00 pieces
1.1.37 25mm dia. U bolt with nut and washer 115.00 pieces
1.1.38 20mm dia. U bolt with nut and washer 115.00 pieces
1.1.39 15mm dia. U bolt with nut and washer 180.00 pieces
1.1.40 12mm dia. U bolt with nut and washer 122.00 pieces
1.1.41 welding filler rod, silver 7.00 kgs
1.1.42 oxygen 5.00 cyls
1.1.43 acetylene 1.00 cyls
1.1.44 sodium bicarbonate 2.00 kgs
1.1.45 nitrogen 50.00 cyls
1.1.46 12mm dia. x 3m long, PVC Pipe 5.00 pieces
1.1.47 25mm dia. x 3m long, PVC Pipe 2.00 pieces
1.1.48 50mm dia. x 3m long, PVC Pipe 1.00 pieces
1.1.49 12mm dia. expansion bolt 250.00 pieces
1.1.50 10mm dia. expansion bolt 250.00 pieces
1.1.51 steel brush 10.00 pieces
1.1.52 primer paint 1.00 gallons
1.1.53 enamel 1.00 gallons
1.1.54 paint brush 1.00 pieces
1.1.55 paint thinner 1.00 gallons
1.1.56 portland cement 1.00 bags
1.1.57 washed sand 1.00 cu m
sub-total

1.2 Outlets, Alarms and Zone Valves


1.2.1 bed head unit, 2.0 meters long 1.00 sets
1.2.2 oxygen outlet, UL/FM 26.00 sets
1.2.3 air outlet, UL/FM 14.00 sets
1.2.4 vacuum inlet, UL/FM 14.00 sets
1.2.5 Zone Valve with Alarm, UL/FM 3.00 sets

sub-total

2. FIRE SPRINKLER SYSTEM-Grid A-K/5-12


2.1 Pipes, Valves and Fittings
2.1.1 water flow detector, UL/FM 2.00 pieces
2.1.2 gate valve supervisory switch 2.00 pieces
2.1.3 25 mm dia. Drain valve 6.00 pieces
2.1.4 25 mm dia. Sight Glass, UL/FM 6.00 pieces
2.1.5 100mmØ floor control valve assembly 2.00 set
2.1.6 50mm dia. gate valve 2.00 pieces
2.1.7 pressure gauge 2.00 pieces
2.1.8 100 mm dia. Check valve 1.00 pieces
2.1.9 100 mm dia. B.I. pipes, S-40 @ 6 M 6.00 length
2.1.10 75 mm dia. B.I. pipes, S-40 @ 6 M Page 32 of 35 28.00 length
Republic of the Philippines
Department of Health

BILL OF QUANTITIES

CONSTRUCTION OF PRESIDENTIAL SECURITY GROUP STATION HOSPITAL PHASE 1


Malacañang Park, Manila
Project Name and Location

Item
DESCRIPTION QTY UNIT UNIT COST TOTAL COST
No.
A. GENERAL
2.1.11 REQUIREMENTS
65 mm dia. B.I. pipes, S-40 @ 6 M 12.00 length
2.1.12 50 mm dia. B.I. pipes, S-40 @ 6 M 8.00 length
2.1.13 38 mm dia. B.I. pipes, S-40 @ 6 M 18.00 length
2.1.14 30 mm dia. B.I. pipes, S-40 @ 6 M 21.00 length
2.1.15 25 mm dia. B.I. pipes, S-40 @ 6 M 214.00 length
2.1.16 38mmØ thread-o-let 36.00 pcs.
2.1.17 30mmØ thread-o-let 60.00 pcs.
2.1.18 38 x 30 mm dia. B.I., tee reducer 50.00 pcs.
2.1.19 38 x 25 mm dia. B.I., tee reducer 41.00 pcs.
2.1.20 30 x 25 mm dia. G.I., tee reducer 30.00 pcs.
2.1.21 25 x 12 mm dia. B.I., reducer 87.00 pcs.
2.1.22 30 mm dia. Union patente 12.00 pcs.
2.1.23 100mm dia companion flange with BNG 48.00 pcs.
2.1.24 65mm dia companion flange with BNG 12.00 pcs.
2.1.25 38mm dia companion flange with BNG 26.00 pcs.
2.1.26 100mmØ VICTAULIC coupling 10.00 sets
2.1.27 75mmØ VICTAULIC coupling 22.00 sets
2.1.28 100mm dia. B.I., Tee 12.00 pcs.
2.1.29 75mmØ B.I. Tee 14.00 pcs.
2.1.30 65mmØ B.I. Tee 6.00 pcs.
2.1.31 50mm dia. B.I., Tee 8.00 pieces
2.1.32 38mm dia. B.I., Tee 25.00 pcs.
2.1.33 25 mm dia. B.I., Tee 145.00 pcs.
2.1.34 100 mm dia. B.I. Elbow 9.00 pieces
2.1.35 65 mm dia. B.I. Elbow 28.00 pieces
2.1.36 50 mm dia. B.I. Elbow 8.00 pieces
2.1.37 25 mm dia. B.I. Elbow 108.00 pcs.
2.1.38 25 x 12 mm dia Bell reducer 215.00 pcs.
2.1.39 acetylene 15.00 cyls
2.1.40 oxygen 40.00 cyls
2.1.41 welding materials 400.00 kgs
2.1.42 firehose cabinet 6.00 sets
2.1.43 #16 TF electric wire 3.00 rolls
2.1.44 15mm dia IMC conduit 45.00 pieces
2.1.45 100mm junction box 12.00 pieces
2.1.46 sprinkler heads 324.00 sets
2.1.47 alarm check valve assembly 1.00 set
2.1.48 clean gas fire suppression sytem for radiology 72.50 sq m

sub-total

2.2 Firepump and Jockey pump


2.2.1 fire pump, w/ controller, AC motor, UL/FM 1.00 set
2.2.2 jockey pump, w/ controller, AC motor, UL/FM 1.00 set
2.2.3 sprinkler alarm control panel 1.00 set
2.2.4 electrical works 1.00 lot
2.2.5 welding materials 200.00 kgs
2.2.6 50mm dia float valve 1.00 pieces
2.2.7 100 mm dia. O S and Y valve 5.00 pieces
2.2.8 100mm dia check valve 2.00 pieces
2.2.9 30 mm dia. GATE valve 2.00 pieces
2.2.10 30mm dia check valve 1.00 pieces
2.2.11 100mm dia companion flange with BNG 4.00 pairs
2.2.12 50 mm dia. B.I. pipes, S-40 @ 6 M 15.00 length
2.2.13 100 mm dia. B.I. pipes, S-40 @ 6 M 5.00 length
2.2.14 30 mm dia. B.I. pipes, S-40 @ 6 M 1.00 length

sub-total
Page 33 of 35
Republic of the Philippines
Department of Health

BILL OF QUANTITIES

CONSTRUCTION OF PRESIDENTIAL SECURITY GROUP STATION HOSPITAL PHASE 1


Malacañang Park, Manila
Project Name and Location

Item
DESCRIPTION QTY UNIT UNIT COST TOTAL COST
No.
A.2.3
GENERAL
FirewaterREQUIREMENTS
Tank and Pumphouse
2.3.1 Earthworks
a. excavation and dewatering 38.00 cu.m.
b. backfill and compaction 19.00 cu.m.
c. excess fill disposal/hauling 20.00 cu.m.

sub-total

2.3.2 Concrete and Rebar works


a. ready mixed concrete 19.90 cu.m.
b. 20mm dia RSB 1,598.40 kgs.
c. 16mm dia RSB 2,979.90 kgs.
d. 12mm dia RSB 1,598.40 kgs.
e. 10mm dia RSB 518.00 kgs.
f. crushed gravel 14.00 cu. m.
g. non-toxic water proofing 79.00 sq. m.
h. polyethylene sheet 20.00 sq. m.
i. ga. 16 tie wire 200.00 kgs.
j. concrete pavement 2.20 cu.m.
k. ladder rung, stainless steel 1.00 pieces
l. manhole cover, 6mm thick MS plate 2.00 pieces

sub-total

2.3.3 Formworks, Scaffoldings/Shoring


a. 1/2" x 4' x 8' form plywood 30.00 pieces
b. 2" x 4" form lumber 1,700.00 bd.ft.
c. 2" x 3" form lumber 2,000.00 bd.ft.
d. 4" x 4" form lumber 2,500.00 bd.ft.
e. tiewire 150.00 kgs.
f. assorted nails 100.00 kgs.

sub-total

2.3.4 Masonry Works


a. portland cement 75.00 bags
b. sand 20.00 cu. m.
c. crushed gravel 7.00 cu. m.
d. 6" CHB 1,500.00 pieces
e. 20mm dia x 6m RSB 300.00 kgs
f. 12mm dia x 6m RSB 500.00 kgs
g. 10mm dia x 6m RSB 200.00 kgs
h. ga. 16 tiewire 50.00 kgs
i. steel ladder, caged, mild steel 1.00 set
j. W-1, steel louver window 4.00 pieces
k. D-1, steel louver door 1.00 pieces
l. insect screen 16.00 sq m

sub-total

2.3.5 Painting Works


a. latex paint 12.00 gallons
b. concrete neutralizer 1.00 liters
c. red lead primer 2.00 gallons
d. paint thinner 1.00 gallons
e. glazing putty 1.00 gallons
f. calsomine 1.00 bags

sub-total
Page 34 of 35
Republic of the Philippines
Department of Health

BILL OF QUANTITIES

CONSTRUCTION OF PRESIDENTIAL SECURITY GROUP STATION HOSPITAL PHASE 1


Malacañang Park, Manila
Project Name and Location

Item
DESCRIPTION QTY UNIT UNIT COST TOTAL COST
No.
A. GENERAL REQUIREMENTS
3.0 VENTILATION AND AIR CONDITIONING - Grid A-K/5-12
3.1 0.75 TR fan coil unit, wall mounted 25.00 sets
3.2 1.0 TR fan coil unit, wall mounted 37.00 sets
3.3 1.5 TR fan coil unit, wall mounted 53.00 sets
3.4 2.0 TR fan coil unit, wall mounted 2.00 sets
3.5 23.5 TR air cooled condensing unit, VRV 1.00 set
3.6 22 TR air cooled condensing unit, VRV 2.00 sets
3.7 19.25 TR air cooled condensing unit, VRV 1.00 sets
3.8 16 TR air cooled condensing unit, VRV 2.00 set
3.9 14 TR air cooled condensing unit, VRV 1.00 set
3.10 13 TR air cooled condensing unit, VRV 1.00 set
3.11 condensate drainage pipe with insulation 145.00 meters
3.12 20 lps exhaust fan, ceiling mounted, cassette type 24.00 pcs.
3.13 70 lps exhaust fan, ceiling mounted, cassette type 1.00 pc
3.14 95 lps exhaust fan, ceiling mounted, cassette type 3.00 pcs.
3.15 100mmØ air duct, G.I. 39.00 meters
3.16 100mmØ vent cap, with insect screen 24.00 pcs.
3.17 150mmØ air duct, G.I. 17.00 meters
3.18 150mmØ vent cap, with insect screen 4.00 pcs.
3.19 wired controller 117.00 pcs.
3.20 Indoor jointed pipe 117.00 pcs.
3.21 refrigerant pipes, refrigerant, fittings, insulation 305.00 meters

sub-total

ELEVATOR SYSTEM
4.0 Bed elevator, 1600 kgs capacity, machineroomless 1.00 sets

sub-total

TOTAL MECHANICAL WORKS

TOTAL PROJECT COST

Page 35 of 35

S-ar putea să vă placă și