Documente Academic
Documente Profesional
Documente Cultură
Between Flange
Proportioners
(3, 4, 6, and 8 in.)
Application
ANSUL® proportioners are specifically designed to accurately 001152
proportion and control the mixing of pressurized ANSUL foam
concentrates into a water stream with minimum pressure loss.
ANSUL proportioners are UL Listed and FM Approved with Specifications
various ANSUL foam concentrates, and are used in conjunction
with bladder tanks and pump proportioning skids. Typical The proportioner body and inlet nozzle shall be of low zinc (less
applications include flammable liquid storage tanks, loading than 15%) brass. The nozzle and foam orifice retaining rings shall
racks, aircraft hangars, heliports, and anywhere flammable liquids be of stainless steel.
are used, stored, processed, or transported. The proportioner body shall be designed so that it fits between
two ANSI 150 lb pipe flanges. Only the recovery section of the
proportioner shall protrude into the system water piping. To
Description capture and seal against the flange gaskets, the mating face
Each ANSUL proportioner consists of a body, inlet nozzle, and shall be machined with 32 grooves per inch (25 mm) for the 4,
metering orifice, all of which are corrosion-resistant brass. 6, and 8 in. models, and 64 grooves per inch (25 mm) for the 3
in. model. The body shall be clearly marked with a flow direction
The proportioner body design includes four sizes to fit between arrow, and the type and percent of foam concentrate that it was
a 3 in., 4 in., 6 in., or 8 in. pipe flange. Clearly marked on the designed to proportion.
proportioner body is the flow direction arrow, as well as the type
and percentage of the designated concentrate. The convergent inlet nozzle shall have a rounded inlet and a
smooth machined finish to ensure minimum stream
The inlet nozzle is secured by a stainless steel retaining ring that constriction and maximum velocity. It shall be retained by an
is internally concealed to prevent removal after installation. internally concealed retaining ring that prevents removal after
The metering orifice is sized according to the type and percent- installation.
age of concentrate used and is also secured with a stainless steel The foam concentrate metering orifice shall be machined to the
retaining ring. proper diameter for the agent. It shall rest on a machined surface
to prevent leakage and shall be secured by a removable stainless
steel retaining ring.
D
F
RETAINING INLET
RING NOZZLE
METERING
ORIFICE
001200 001199
BODY
N.
Foam
N.
8I
4I
N.
(10.3) 150
2% JET-X Foam 70817** 69369** 69387** 69407*
6I
2 3/4% JET-X Foam 70816* 69366* 69386* 69406*
N.
3I
0.5% SILV-EX Foam 70818 — — — WATER INLET PRESSURE (6.9) 100
Shipping Weight 10 lb 20 lb 40 lb 70 lb
(4.5 kg) (9.1 kg) (18.1 kg) (31.8 kg)
* UL Listed with Bladder Tanks
** UL Listed and FM Approved with Bladder Tanks (3.4) 50
Proportioners are only FM Approved when used in conjunction with the (2.8) 40
specific foam concentrates and equipment shown in the Approval Guide
(www.ApprovalGuide.com).
(2.1) 30
Safety Data Sheet (SDS) available at www.ansul.com
Note: The converted values in this document are provided for dimensional (1.4) 20
reference only and do not reflect an actual measurement. 400 700 1000 2000 3000 5000 gpm
ANSUL, JET-X, and the product names listed in this material are marks and/ (1514) (2650) (3785) (7571) (11356) (18927) (Lpm)
or registered marks. Unauthorized use is strictly prohibited. WATER FLOW
N.
6I
8I
(1.03) 15
N.
N.
4I
3I
(0.41) 6
(0.34) 5
(0.28) 4
(0.21) 3
(0.17) 2.5
(0.14) 2
(0.10) 1.5
(0.07) 1
150 200 300 400 600 1000 2000 3000 5000 7000 gpm
(568) (757) (1136) (1514) (2271) (3785) (7571) (11356) (18927) (26498) (Lpm)
FLOW RATE