Documente Academic
Documente Profesional
Documente Cultură
making steelwork
Purlins
TECHNOLOGY
BW Purlins 2 TEL 01262 400088 • EMAIL sales@bw-industries.co.uk • WEB www.bw-industries.co.uk
Introduction .................................................................................................... 3
Design
All of BW Industries steel section Certification
property information and load
tables have been independently
BW Industries have developed design software
assessed and verified under based on the methodology in the relevant European
the “SCI Assessed” Scheme standards and extensive testing of their product range.
“Calculation of the member
resistances”. The section This information has been independently assessed
properties are calculated in and approved by the SCI who are an internationally
accordance with BS-EN 1993-1-3
(Design of steel structures,, Part recognized authority in the field of light gauge
1-3 General rules – Supplementary steelwork design and construction.
rules for cold-formed members and
sheeting BSI 2006). BW Industries are pleased to display the SCI logo
CE Marking and to confirm that their products have achieved
SCI Assessed status with the
BW Industries Limited
“Factory Production Control” was appropriate certification.
third party assessed against
EN 1090-1:2009+A1 2011, by SGS
UK. We achieved accreditation to
EXC2 and standard ISO 14731 and
ISO 3834.
This certification covers the
following products: Steel
Structural Purlins, Mezzanine Steel
Channels, Fabricated Structural
Steel Assemblies and SureBUILD
Engineered Wall Panels.
Dispatch and Supply
BW Industries have a team of
experienced personnel who hand
pick the items for dispatch and
load these onto the vehicles that
have been arranged for onward
transportation.
Depending on the end users
requirements, specialist vehicles
with on board lifting equipment can
be arranged to facilitate off-loading
Photograph of Zed Purlin undergoing load testing in the John Payne Building
at the delivery address. Laboratory at Oxford Brookes University as witnessed and documented by the
SCI (Steel Construction Institute)
BW Purlins 6 TEL 01262 400088 • EMAIL sales@bw-industries.co.uk • WEB www.bw-industries.co.uk
BW Cleat Details
page 21
Range Gauges mm
Top Flange
Use the
Z121 1.3 , 1.4 , 1.5 , 1.6 , 1.8 , 2.0
BW Building
Z141 1.3 , 1.4 , 1.5 , 1.6 , 1.8 , 2.0
Z151 1.3 , 1.4 , 1.5 , 1.6 , 1.8 , 2.0
Wizard
Top
p Lip
Top Hole Z171 1.3 , 1.4 , 1.5 , 1.6 , 1.8 , 2.0 , 2.3 , 2.5
Software
Z201 1.4 , 1.5 , 1.6 , 1.8 , 2.0 , 2.3 , 2.5 for accurate
Gauge
Z231 1.5 , 1.6 , 1.8 , 2.0 , 2.3 , 2.5 calculations
Z261 1.6 , 1.8 , 2.0 , 2.3 , 2.5 , 2.9
Z301 2.0 , 2.3 , 2.5 , 2.9
Depth Z341 2.3 , 2.5 , 2.7 , 3.0
Range Depth Top Top Lip Bottom Bottom Top Hole Bottom
mm Flange mm Flange Lip mm Hole
mm mm mm mm
The software package facilitates cost effective design of purlins, side rails and mezzanine floor beams all in accordance with
current standards. An integral database allows for quick and accurate assessment of loadings including wind load and snow
INDUSTRIES load for all locations in the United Kingdom and Ireland. This all in one application enables production of detailed reports for
making steelwork
submission to any checking authority. See our website or contact our sales team to request the latest version.
Building Wizard Software
TEL 01262 400088 • EMAIL sales@bw-industries.co.uk • WEB www.bw-industries.co.uk 9 BW Purlins
Moment
Second Moment of Area Section Modulus Radius of Gyration
Section Weight Capacity
Reference kg/m Major Axis Minor Axis Major Axis Minor Axis Major Axis Minor Axis Major Axis
cm4 cm4 cm3 cm3 cm cm kNm
Z12113 2.59 74.01 23.05 12.07 4.24 4.81 2.68 5.03
Z12114 2.78 79.39 24.66 12.94 4.54 4.80 2.67 5.72
Z12115 2.97 84.70 26.23 13.81 4.83 4.79 2.67 6.40
Z12116 3.16 89.93 27.78 14.66 5.12 4.78 2.66 7.08
Z12118 3.53 100.20 30.77 16.34 5.68 4.77 2.64 8.40
Z12120 3.89 110.18 33.64 17.97 6.22 4.75 2.62 9.68
Z14113 2.79 105.74 23.12 14.81 4.24 5.53 2.59 6.17
Z14114 3.00 113.48 24.73 15.90 4.54 5.52 2.58 7.02
Z14115 3.20 121.13 26.32 16.97 4.84 5.51 2.57 7.87
Z14116 3.41 128.69 27.87 18.03 5.13 5.51 2.56 8.70
Z14118 3.81 143.52 30.89 20.11 5.70 5.49 2.55 10.33
Z14120 4.21 157.99 33.79 22.13 6.24 5.47 2.53 11.93
Z15113 2.89 124.17 23.14 16.25 4.25 5.89 2.54 6.77
Z15114 3.11 133.29 24.76 17.45 4.55 5.88 2.53 7.71
Z15115 3.32 142.31 26.35 18.63 4.84 5.87 2.53 8.63
Z15116 3.53 151.22 27.91 19.79 5.13 5.86 2.52 9.55
Z15118 3.95 168.72 30.94 22.08 5.70 5.84 2.50 11.35
Z15120 4.36 185.81 33.85 24.32 6.25 5.83 2.49 13.11
Z17113 3.32 186.23 37.64 21.56 5.75 6.73 3.03 7.54
Z17114 3.57 200.06 40.33 23.16 6.16 6.72 3.02 8.79
Z17115 3.82 213.74 42.97 24.75 6.57 6.71 3.01 10.04
Z17116 4.06 227.29 45.57 26.31 6.97 6.70 3.00 11.27
Z17118 4.54 253.96 50.64 29.40 7.76 6.69 2.99 13.69
Z17120 5.02 280.09 55.54 32.43 8.52 6.67 2.97 16.07
Z17123 5.73 318.27 62.59 36.85 9.63 6.65 2.95 19.55
Z17125 6.20 343.04 67.09 39.71 10.33 6.63 2.93 21.81
Z20114 3.90 292.20 40.43 28.81 6.17 7.77 2.89 10.94
Z20115 4.17 312.31 43.09 30.79 6.58 7.76 2.88 12.49
Z20116 4.44 332.25 45.70 32.76 6.98 7.76 2.88 14.03
Z20118 4.97 371.56 50.81 36.63 7.78 7.74 2.86 17.06
Z20120 5.50 410.14 55.75 40.44 8.55 7.72 2.85 20.04
Z20123 6.28 466.64 62.86 46.01 9.66 7.69 2.82 24.41
Z20125 6.79 503.41 67.41 49.63 10.37 7.68 2.81 27.25
Z23115 4.76 472.25 63.17 40.37 8.30 8.94 3.27 14.03
Z23116 5.06 502.66 67.06 42.97 8.82 8.93 3.26 16.07
Z23118 5.67 562.75 74.68 48.10 9.84 8.91 3.25 20.09
Z23120 6.28 621.87 82.09 53.16 10.83 8.89 3.23 24.05
Z23123 7.18 708.72 92.81 60.58 12.27 8.87 3.21 29.87
Z23125 7.77 765.42 99.70 65.43 13.19 8.85 3.19 33.68
Z26116 5.53 689.05 75.94 52.07 9.51 10.01 3.32 18.45
Z26118 6.20 771.92 84.63 58.34 10.61 9.99 3.31 23.35
Z26120 6.86 853.56 93.09 64.51 11.68 9.97 3.29 28.17
Z26123 7.85 973.74 105.36 73.59 13.25 9.94 3.27 35.29
Z26125 8.50 1052.34 113.26 79.53 14.26 9.92 3.26 39.94
Z26129 9.78 1205.94 128.40 91.13 16.21 9.89 3.23 49.04
Z30120 7.87 1299.79 134.69 85.32 15.02 11.49 3.70 33.92
Z30123 9.00 1484.83 152.78 97.47 17.06 11.46 3.68 43.42
Z30125 9.75 1606.17 164.48 105.43 18.39 11.45 3.66 49.65
Z30129 11.24 1844.04 187.04 121.05 20.96 11.41 3.63 61.87
Z34123 10.16 2149.05 212.63 124.69 21.36 12.99 4.08 51.30
Z34125 11.01 2326.33 229.18 134.98 23.04 12.97 4.07 59.34
Z34127 11.86 2501.54 245.38 145.14 24.70 12.95 4.06 67.29
Z34130 13.12 2760.50 269.04 160.16 27.12 12.92 4.03 79.05
BW Purlins 10 TEL 01262 400088 • EMAIL sales@bw-industries.co.uk • WEB www.bw-industries.co.uk
Range Gauges mm
Flange Use the
C121 1.3 , 1.4 , 1.5 , 1.6 , 1.8 , 2.0
BW Building
Lip C141 1.3 , 1.4 , 1.5 , 1.6 , 1.8 , 2.0
Hole C151 1.3 , 1.4 , 1.5 , 1.6 , 1.8 , 2.0
Wizard
Gauge C171 1.3 , 1.4 , 1.5 , 1.6 , 1.8 , 2.0 , 2.3 , 2.5
Software
C201 1.4 , 1.5 , 1.6 , 1.8 , 2.0 , 2.3 , 2.5 for accurate
C231 1.5 , 1.6 , 1.8 , 2.0 , 2.3 , 2.5 calculations
C261 1.6 , 1.8 , 2.0 , 2.3 , 2.5 , 2.9
C301 2.0 , 2.3 , 2.5 , 2.9
Depth C341 2.3 , 2.5 , 2.7 , 3.0
C121 121 54 17 43
Hole
C141 141 54 17 43
Lip
C151 151 54 17 43
C171 171 66 17 43
C201 201 66 17 43
C231 231 75 17 43
C261 261 79 17 43
C301 301 89 19 43
C341 341 99 21 43
The software package facilitates cost effective design of purlins, side rails and mezzanine floor beams all in accordance with
current standards. An integral database allows for quick and accurate assessment of loadings including wind load and snow
INDUSTRIES load for all locations in the United Kingdom and Ireland. This all in one application enables production of detailed reports for
making steelwork
submission to any checking authority. See our website or contact our sales team to request the latest version.
Building Wizard Software
TEL 01262 400088 • EMAIL sales@bw-industries.co.uk • WEB www.bw-industries.co.uk 11 BW Purlins
Moment
Second Moment of Area Section Modulus Radius of Gyration
Section Weight Capacity
Reference kg/m Major Axis Minor Axis Major Axis Minor Axis Major Axis Minor Axis Major Axis
cm4 cm4 cm3 cm3 cm cm kNm
C12113 2.58 74.01 13.36 12.23 3.72 4.82 2.05 5.25
C12114 2.77 79.39 14.30 13.12 3.98 4.81 2.04 5.95
C12115 2.96 84.70 15.22 14.00 4.24 4.80 2.03 6.64
C12116 3.14 89.94 16.12 14.87 4.49 4.79 2.03 7.32
C12118 3.51 100.20 17.87 16.56 4.98 4.78 2.02 8.66
C12120 3.88 110.18 19.56 18.21 5.45 4.76 2.01 9.96
C14113 2.78 105.67 14.08 14.99 3.79 5.54 2.02 6.43
C14114 2.99 113.41 15.08 16.09 4.06 5.53 2.02 7.29
C14115 3.19 121.05 16.05 17.17 4.32 5.52 2.01 8.14
C14116 3.39 128.60 17.01 18.24 4.58 5.51 2.01 8.98
C14118 3.80 143.42 18.87 20.34 5.08 5.50 1.99 10.63
C14120 4.19 157.87 20.66 22.39 5.57 5.48 1.98 12.24
C15113 2.88 124.06 14.41 16.43 3.82 5.90 2.01 7.05
C15114 3.10 133.17 15.43 17.64 4.09 5.89 2.00 7.99
C15115 3.31 142.18 16.42 18.83 4.36 5.88 2.00 8.93
C15116 3.52 151.08 17.40 20.01 4.62 5.87 1.99 9.85
C15118 3.94 168.56 19.31 22.33 5.12 5.85 1.98 11.67
C15120 4.35 185.63 21.15 24.59 5.61 5.84 1.97 13.44
C17113 3.33 187.81 24.25 21.97 5.23 6.75 2.42 7.81
C17114 3.58 201.75 25.99 23.60 5.61 6.74 2.42 9.09
C17115 3.83 215.56 27.71 25.21 5.98 6.73 2.41 10.36
C17116 4.07 229.22 29.40 26.81 6.34 6.72 2.41 11.61
C17118 4.56 256.13 32.70 29.96 7.06 6.71 2.40 14.08
C17120 5.04 282.49 35.90 33.04 7.75 6.69 2.38 16.51
C17123 5.75 321.00 40.52 37.54 8.75 6.66 2.37 20.05
C17125 6.22 346.00 43.47 40.47 9.39 6.65 2.36 22.35
C20114 3.91 294.41 27.36 29.29 5.71 7.79 2.38 11.29
C20115 4.18 314.69 29.17 31.31 6.09 7.78 2.37 12.86
C20116 4.45 334.77 30.96 33.31 6.46 7.77 2.36 14.43
C20118 4.98 374.39 34.45 37.25 7.19 7.76 2.35 17.51
C20120 5.51 413.27 37.84 41.12 7.90 7.74 2.34 20.54
C20123 6.29 470.23 42.73 46.79 8.93 7.71 2.32 24.98
C20125 6.81 507.29 45.87 50.48 9.59 7.69 2.31 27.88
C23115 4.75 471.52 41.54 40.82 7.53 8.94 2.65 14.84
C23116 5.05 501.88 44.12 43.45 7.99 8.93 2.65 16.89
C23118 5.66 561.86 49.17 48.65 8.91 8.92 2.64 20.96
C23120 6.26 620.87 54.09 53.75 9.80 8.90 2.63 24.96
C23123 7.16 707.56 61.22 61.26 11.10 8.87 2.61 30.83
C23125 7.75 764.15 65.81 66.16 11.94 8.85 2.60 34.67
C26116 5.53 690.54 51.97 52.92 8.78 10.02 2.75 19.53
C26118 6.20 773.59 57.96 59.28 9.80 10.00 2.74 24.50
C26120 6.86 855.41 63.80 65.55 10.79 9.98 2.73 29.40
C26123 7.85 975.84 72.28 74.78 12.23 9.95 2.71 36.62
C26125 8.50 1054.61 77.76 80.81 13.16 9.93 2.70 41.34
C26129 9.78 1208.52 88.29 92.61 14.95 9.90 2.68 50.58
C30120 7.80 1288.47 89.43 85.61 13.25 11.49 3.03 35.04
C30123 8.93 1471.76 101.51 97.79 15.04 11.46 3.01 44.56
C30125 9.75 1609.07 113.51 106.92 16.96 11.46 3.04 51.35
C30129 11.24 1847.36 129.25 122.75 19.32 11.42 3.02 63.74
C34123 10.16 2152.39 147.22 126.24 19.69 13.00 3.40 53.23
C34125 11.01 2329.94 158.77 136.65 21.24 12.98 3.39 61.36
C34127 11.86 2505.42 170.10 146.95 22.76 12.96 3.38 69.40
C34130 13.12 2764.77 186.66 162.16 24.98 12.93 3.36 81.29
BW Purlins 12 TEL 01262 400088 • EMAIL sales@bw-industries.co.uk • WEB www.bw-industries.co.uk
Range Gauges mm
e E195 2.0, 2.4, 3.0
Flang Lip
E235 2.0, 2.4, 3.0
E300 2.0, 2.4, 3.0
Angle of Top Flange
E360 2.0, 2.4, 3.0
from 0 to 20 degrees
Moment
Second Moment of Area Section Modulus Radius of Gyration
Section Weight Capacity
Reference kg/m Major Axis Minor Axis Major Axis Minor Axis Major Axis Minor Axis Major Axis
cm4 cm4 cm3 cm3 cm cm kNm
19520 6.26 478.52 84.57 49.08 13.69 7.81 3.28 19.89
19524 7.46 567.16 99.63 58.17 16.14 7.78 3.26 27.06
19530 9.21 694.53 120.88 71.23 19.58 7.73 3.22 37.38
23520 6.89 736.90 89.97 62.71 14.02 9.24 3.23 25.42
23524 8.21 874.75 106.07 74.45 16.53 9.21 3.21 34.64
23530 10.15 1073.74 128.84 91.38 20.08 9.16 3.17 47.95
30020 7.91 1307.16 97.00 87.14 14.40 11.49 3.13 35.32
30024 9.44 1554.59 114.45 103.64 17.00 11.45 3.11 48.22
30030 11.68 1913.67 139.20 127.58 20.70 11.40 3.07 66.94
36020 8.85 2019.15 102.10 112.18 14.67 13.50 3.04 45.47
36024 10.57 2404.43 120.54 133.58 17.33 13.46 3.01 62.15
36030 13.09 2965.60 146.74 164.76 21.11 13.40 2.98 86.45
The software package facilitates cost effective design of purlins, side rails and mezzanine floor beams all in accordance with
current standards. An integral database allows for quick and accurate assessment of loadings including wind load and snow
INDUSTRIES load for all locations in the United Kingdom and Ireland. This all in one application enables production of detailed reports for
making steelwork
submission to any checking authority. See our website or contact our sales team to request the latest version.
Building Wizard Software
TEL 01262 400088 • EMAIL sales@bw-industries.co.uk • WEB www.bw-industries.co.uk 13 BW Purlins
Single Span
Double Span
The sleeved purlin system is suitable for buildings with two The sleeves, which achieve a high degree of continuity over the
or more bays and utilises single span length purlins with purlin supports are fitted at all penultimate rafter connections and
sleeves. The sleeves are formed from the same section as staggered on all internal bays, allow economy of purlin section
the purlins but are installed inverted. selection.
The system can be used for single span purlins and for double
span purlins.
TEL 01262 400088 • EMAIL sales@bw-industries.co.uk • WEB www.bw-industries.co.uk 15 BW Purlins
The butted purlin system is suitable for all building types but is
primarily used in single span applications.
It is the simplest purlin system and can be used in inset and
oversail configurations.
Non standard end configurations can be accommodated
as required.
BW “Z” Section Standard Hole Details BW “Z” Section Standard Hole Details Double
Non-continuous Spanning Butt-jointed
Holes for purlin ties at mid-span or one third and two thirds Holes for purlin ties at mid-span or one third and two thirds
span points. span points.
Length of purlin is span less 6mm. Length of left hand span plus length of right hand span less 6mm.
Holes for purlin ties are 18mm diameter. Holes for purlin ties are 18mm diameter.
The software package facilitates cost effective design of purlins, side rails and mezzanine floor beams all in accordance with
current standards. An integral database allows for quick and accurate assessment of loadings including wind load and snow
INDUSTRIES load for all locations in the United Kingdom and Ireland. This all in one application enables production of detailed reports for
making steelwork
submission to any checking authority. See our website or contact our sales team to request the latest version.
Building Wizard Software
TEL 01262 400088 • EMAIL sales@bw-industries.co.uk • WEB www.bw-industries.co.uk 17 BW Purlins
The heavy end bay system is a variation of the sleeved system which
is suitable for buildings with five or more bays.
Heavier gauge sections are fitted to the end bays with corresponding
heavy gauge sleeves to all penultimate rafter connections.
Inner bay purlins are of lighter gauge as are the inner bay sleeves
which are fitted at every connection.
BW ‘Z’ Section Standard Hole Details The system can be used with double span inner bay purlins with
fewer inner sleeves.
Holes for purlin ties at mid-span or one third and two thirds span points.
Holes for purlin ties are 18mm diameter.
Monopitch Roof
Use the For monopitch and other roofs where there is no restraint to the
BW Building ridge purlin via apex ties an equivalent anchor must be used
Wizard (ie threaded bar). This may take the form of a simple tie to a
substantial ridge beam or alternatively by a combination of struts
Software and diagonal bracing between the top two purlins.
for accurate Restraints should be used at mid-span for purlin spans greater than
calculations 3.5m and at third points of span for purlin spans greater than 7.5m.
For long roof slopes additional diagonal bracing may be required
depending on sheeting.
Tiled/Mansard Roof
Steep Roof
The software package facilitates cost effective design of purlins, side rails and mezzanine floor beams all in accordance with
current standards. An integral database allows for quick and accurate assessment of loadings including wind load and snow
INDUSTRIES load for all locations in the United Kingdom and Ireland. This all in one application enables production of detailed reports for
making steelwork
submission to any checking authority. See our website or contact our sales team to request the latest version.
Building Wizard Software
TEL 01262 400088 • EMAIL sales@bw-industries.co.uk • WEB www.bw-industries.co.uk 21 BW Purlins
130 130
30 30
70 30
30
C
A
C
A 65 65
35
30 30
D
D
T T
Range A B C D T Type A B C D T
mm mm mm mm mm mm mm mm mm mm
Alternative bolt on type cleats can be supplied in either Flat Plate Alternative weld on cleats can be supplied without baseplate.
Form or Angle (excluding bottom flange holes).
Packer Plates
Finish: galvanised or primer paint. All dimensions in millimetres
30
36 diameter
30
hole
30
30 Rail Packers 30
PJR Packers
60
30
30
141 55 141 55
60
*used to accept counter formed holes *used when side rail supports are at 3rd points
BW Purlins 22 TEL 01262 400088 • EMAIL sales@bw-industries.co.uk • WEB www.bw-industries.co.uk
NOTE: When ordering ancillary items, please ensure the correct production details are given for each item. It is our intent to avoid any
unnecessary delay or error, which misleading information may cause.
BW ‘Snaptite’
Purlin Anti-sag Ties
n BW ‘Snaptite’ Ties also prevent the purlin from ‘rotating’ during n In some cases Anti-sag Ties are not required for roof pitches
installation whilst assisting with restraining the bottom flange above 4 degrees. This can require that temporary props/
against wind uplift. The rigidity of the purlin is greatly enhanced bars are used until the sheeting is fixed. The maximum spans
once the roof sheeting is installed without ties are:
n BW ‘Snaptite’ Anti-sag Ties should be fitted when a purlin span is Z141, Z151, Z171, Z201 .......................................... up to 6.1m
in excess of 4.6m so that the laterally unsupported length does Z231 ............................................................................ up to 7.1m
not exceed 3.8m. For Z301 & Z341 Purlins use ‘sheeting rail’ type Z261 ............................................................................. up to 7.6m
angle braces (as diagram) above. Z301, Z341 ................................................................. up to 8.1m
Apex Ties
Apex Ties are used to offer rigid restraint on pitched roofs. Used
in conjunction with anti-sag ties to give perpendicular support to
the purlins.
Apex Ties connect the two uppermost purlins across the ridge
and are usually 12mm screwed rod.
Apex Ties are cranked at centre point. M12 threaded Rod BZP with
M12 Nuts & M12 Flat Washers. 14mm diameter holes required in
purlins to take these ties.
Roof Ties
45 x 45 Angle 2mm Galvanised with 2 No. End Brackets. 14mm dia holes required in
purlins to take these ties.
Purlin Ref 141 151 171 201 231 261 301 341
Hole Centres 56 66 86 116 146 176 216 256
All dimensions in millimetres
The above Roof Ties should be used for pitches below 4º and purlin spacing exceeding
2.5m. These can also be used instead of Eaves Ties.
Where the roof slope is longer than 18m we would recommend the use of the Roof Ties
c/w the diagonal tie system within the roof slope.
Apex roof ties are used in conjunction with above roof ties. For use with the above Roof Ties.
Material: 45x45x2mm angle with 2 no. end brackets. 5mm diameter Galvanised Wire Rope with 2 No. 40 x 8mm
Flat Bar End Brackets.
14mm dia holes required in purlins to take these ties.
14mm dia holes required in purlins to take these wires.
Product information required when ordering Product information required when ordering
roof pitch apex dimensions purlin type purlin centre span hole centres
BW Purlins 24 TEL 01262 400088 • EMAIL sales@bw-industries.co.uk • WEB www.bw-industries.co.uk
Cleader Rail Available in 2 sizes. Both supplied from stock in 6 metre plain
Unpunched lengths.
Small
45x45mm Angle 2mm Galvanised for use where purlin centres
are up to 1.8m
Large
100x100mm Angle 2mm Galvanised for use where purlin
centres are over 1.8m
BW Cleader rail is fixed to the end of the purlins to carry vertical
cladding. A 6mm gap is recommended for joints in the Cleader
Rail. A Jointing Cleat to be used where required – not supplied
by BW (Size suggested 70x60x3mm 50mm long) or simply
overlap by approx 28mm.
*Non-standard cleader can be supplied on request
(c/w holes if required) *
Rafter/Stanchion Stays
Use the
BW Building
Wizard
Software
for accurate
calculations
To securely fix the purlin to the main steelwork frame, stays are used,
fixed as shown by 2 pre-punched 14mm diameter holes.
Product information required when ordering
Detail consists of: L x 45 x 45 x 2 Galv. Steel hole centre dimension
The software package facilitates cost effective design of purlins, side rails and mezzanine floor beams all in accordance with
current standards. An integral database allows for quick and accurate assessment of loadings including wind load and snow
INDUSTRIES load for all locations in the United Kingdom and Ireland. This all in one application enables production of detailed reports for
making steelwork
submission to any checking authority. See our website or contact our sales team to request the latest version.
Building Wizard Software
TEL 01262 400088 • EMAIL sales@bw-industries.co.uk • WEB www.bw-industries.co.uk 25 BW Purlins
Eaves Beam Stiffening Brackets are bolted inside the Eaves Beam
to offer a fixing point for the Eaves Tie Fixing Bracket.
6mm mild steel plate, hot dip galvanised after manufacture, Product information required when ordering
pre-punched with 4 No. 14mm diameter holes.
eaves beam type
BW Purlins 26 TEL 01262 400088 • EMAIL sales@bw-industries.co.uk • WEB www.bw-industries.co.uk
The software package facilitates cost effective design of purlins, side rails and mezzanine floor beams all in accordance with
current standards. An integral database allows for quick and accurate assessment of loadings including wind load and snow
INDUSTRIES load for all locations in the United Kingdom and Ireland. This all in one application enables production of detailed reports for
making steelwork
submission to any checking authority. See our website or contact our sales team to request the latest version.
Building Wizard Software
TEL 01262 400088 • EMAIL sales@bw-industries.co.uk • WEB www.bw-industries.co.uk 27 BW Purlins
Sleeved System
The sleeved side rail system is suitable for buildings with two or section selection.
more bays and utilizes single span length side rails with sleeves.
The system can be used for single span side rails and for double
The sleeves are formed from plain channel section ie without lips.
span side rails.
The sleeves, which achieve a high degree of continuity over the
Sides rails can be supplied in Zeds also
side rail supports are fitted at all penultimate column connections
and staggered on internal bays, allow economy of side rail
The butted side rail system is suitable for all building types but is Non-standard end configurations can be accommodated as
primarily used in single span applications. required.
It is the simplest side rail system and can be used in inset and
oversail configurations. Use the
BW Building
Wizard
Software
for accurate
BW ‘C’ Section Standard Hole Details calculations
Non-continuous
Holes for side rail struts at mid-span or one third and two thirds
span points.
Length of side rail is span less 6mm.
Holes for side rail struts at mid-span or one third and two thirds
span points.
Length of side rail is span less 6mm.
The software package facilitates cost effective design of purlins, side rails and mezzanine floor beams all in accordance with
current standards. An integral database allows for quick and accurate assessment of loadings including wind load and snow
INDUSTRIES load for all locations in the United Kingdom and Ireland. This all in one application enables production of detailed reports for
making steelwork
submission to any checking authority. See our website or contact our sales team to request the latest version.
Building Wizard Software
BW Purlins 30 TEL 01262 400088 • EMAIL sales@bw-industries.co.uk • WEB www.bw-industries.co.uk
15 15
Holes
PJR140 1.6, 2.0
Lip
Range Depth Top Top Lip Bottom Bottom Holes
Depth mm Flange mm Flange Lip mm
mm mm mm
PJR140 140 95 17 95 17 35
Flange
Holes
G140 1.6, 2.0
Lip
Range Depth Top Top Lip Bottom Bottom Holes
Depth mm Flange mm Flange Lip mm
mm mm mm
Flange
TEL 01262 400088 • EMAIL sales@bw-industries.co.uk • WEB www.bw-industries.co.uk 31 BW Purlins
Panel joint rails are formed from 1.6mm thick There is an allowance of 10mm clearance
material for rail centres up to 2m for rail centres above and below panel joint rail between
over 2m use 2mm thick panel joint rails. sheeting rails.
BW ‘Restraint’ or ‘Supporting’ ancillaries are incorporated to reduce loading deformation of the side rails and assist in strengthening the
overall structure when loads are supplied. All loading conditions are specifically calculated, only use BW Products illustrated to ensure
correct stability under wind pressure and suction loads.
For Z141 & Z151 Rails For Z171,Z201, Z231, Z261, Z301, Special Fixing to Eaves Beam
Z341 Rails
Support Cleat Hole Centres Face to Face Hole centres in End Brackets
with Rails. It is recommended that the two
lower rails are fixed first and aligned before Rail Type Z141 Z151 Z171 Z201 Z231 Z261 Z301 Z341
the remaining rails are installed. Centres 56 66 86 116 146 176 216 256
All dimensions in millimetres
BW Clamp Plate
Product information required when ordering
rail centres top & bottom rail type
Detail
Deta
etail A
Detail
etail
ail B
Detail
D etail C
Sheeting Rail
60
25
45
A
Sheeting Rail
60
45
25
We can also manufacture rails with auto-formed ends (manufactured to individual client specification)
TEL 01262 400088 • EMAIL sales@bw-industries.co.uk • WEB www.bw-industries.co.uk 35 BW Purlins
The software package facilitates cost effective design of purlins, side rails and mezzanine floor beams all in accordance with
current standards. An integral database allows for quick and accurate assessment of loadings including wind load and snow
INDUSTRIES load for all locations in the United Kingdom and Ireland. This all in one application enables production of detailed reports for
making steelwork
submission to any checking authority. See our website or contact our sales team to request the latest version.
Building Wizard Software
BW Purlins 36 TEL 01262 400088 • EMAIL sales@bw-industries.co.uk • WEB www.bw-industries.co.uk
In certain applications it is necessary to include fire protection to some or all of the perimeter walls around the building. There are many fire
resistant wall cladding systems which are available today.
‘Butt/Non-Continuous Rail Arrangement’, normally fixed outside ‘Sleeved Rail Arrangement’. Alternate sleeve butt/non-continuous
the columns, but can also be fitted between the columns. Allow connection to column, even number of bays. When odd bays occur,
60mm gap at rail joint for expansion. use the special sleeve. Allow 60mm gap at rail joints for expansion.
Firewall Sleeves
General Notes
The rail or cleat is slotted longitudinally (14mm x 50mm) on the
standard gauge lines. 60mm gap required between ends of rails.
Fixing bolts to all joints must be fitted with a combustible washer.
This will collapse under fire conditions, to allow movement for the
rail to expand.
The period of resistance is solely dependent on the cladding
material used, and the type of construction. A certificate should be
obtained from the cladding supplier.
All primary structural steelwork, supporting the rails and cladding,
should be fire protected.
Profile 6 20 14.0
30.0
(including insulation and battens) Tile Weights
Building Wizard So
ftware
©BW Industries 2011
17
Detail sheets
A full range of detail sheets
are available on request or to
download from our website at
www.bw-industries.co.uk
BW INDUSTRIES
Carnaby Industrial Estate
Carnaby, Bridlington
East Yorks. YO15 3QY
We reserve the right to alter and amend specifications shown at any time
without prior notice. All dimensions are nominal. Care has been taken that
the contents of this publication are accurate. However BW Industries Ltd.
and its associated companies do not accept responsibility for errors or
information found to be misleading and accept no liabilities whatsoever
in respect thereof. The contents of this publication are meant as a general
introduction to our products and any purchaser, specifier or user retains
the entire responsibility for satisfying themselves, independently of anything
herein, as to the suitability or fitness for purpose of any BW Industries Ltd.
products, services or systems. Our normal terms & conditions of business
apply to any order (A copy will be supplied upon request.) © December 2015