Documente Academic
Documente Profesional
Documente Cultură
website:http://biz.LGservice.com
PLASMA TV
SERVICE MANUAL
CHASSIS :PA75C
Keep wires away from high voltage or high temperature parts. Leakage Current Hot Check circuit
AC Volt-meter
Copyright © 2007 LG Electronics. Inc. All right reserved. - 2 - LGE Internal Use Only
Only for training and service purposes
TABLE OF CONTENTS
SPECIFICATIONS.................................................................4
EXPLODED VIEW...............................................................20
SCHEMATIC DIAGRAM..........................................................
Copyright © 2007 LG Electronics. Inc. All right reserved. - 3 - LGE Internal Use Only
Only for training and service purposes
SPECIFICATIONS
Including stand 41.3 x 30.2 x 12.2 inches 48.9 x 34.9 x 14.6 inches
Dimensions 1048.0 x 766.0 x 310.0 mm 1242.0 x 887.6 x 370.0 mm
(Width x Height x Depth) Excluding stand 41.3 x 28.1 x 3.3 inches 48.9 x 32.6 x 3.5 inches
1048.0 x 713.0 x 83.5 mm 1242.0 x 827.2 x 88.0 mm
Copyright © 2007 LG Electronics. Inc. All right reserved. - 4 - LGE Internal Use Only
Only for training and service purposes
ADJUSTMENT INSTRUCTIONS
1. Application Range
This spec sheet is applied all of the PDP TV, PA75C chassis.
O HEAT RUN
Preliminary action is applied to the test for afterimage
discharge detection, and 100% FULL WHITE PATTERN
must be operated automatically.
Copyright © 2007 LG Electronics. Inc. All right reserved. - 5 - LGE Internal Use Only
Only for training and service purposes
ADJUSTMENT INSTRUCTIONS
3-2. Adjustment(60”)
Connection Diagram of Power Adjustment for Measuring
(1) Va Voltage Adjustment (Power Board): 50”
1) Connect + terminal of D.M.M to Va pin of P812 and
connect – terminal to GND pin of P812.
2) Adjust VR901 voltage to match that of the label on the
Top/Right of the panel. (Deviation : ±0.5V) 3-4. Adjustment(42”)
(2) Vs Voltage Adjustment (1) Va Voltage Adjustment
1) Connect + terminal of D.M.M to Vs pin of P812 and 1) Connect + terminal of D.M.M to Va pin of P812 and
connect – terminal to GND pin of P812. connect – terminal to GND pin of P812.
2) Adjust VR951 voltage to match that of the label on the 2) Adjust VR901 voltage to match that of the label on the
Top/Right of the panel. (Deviation : ±0.5V) Top/Right of the panel. (Deviation : ±0.5V)
Copyright © 2007 LG Electronics. Inc. All right reserved. - 6 - LGE Internal Use Only
Only for training and service purposes
ADJUSTMENT INSTRUCTIONS
4. Component 480i/1080p RGB (3) After receiving signal for at least 1 second, press the ADJ
Key on the Service R/C to enter the ‘Ez - Adjust’ and select
1080p Adjustment the ‘4. ADC 1080i Comp1/RGB’.
Component 480i/1080p RGB 1080p adjustment to set the Pressing the Enter Key to adjust automatically component1.
black level and the Gain to optimum. (4) When the adjustment is over, 'ADC Component1 Success’
is displayed. If the adjustment has errors, 'ADC
4-1. Test Equipment Component1 1080i Fail’ is displayed.
(1) Service R/C (5) After the Component1 adjustment is over, convert the
(2) 801GF(802B, 802F, 802R) or MSPG925FA Pattern RGB-DTV Mode and start RGB adjustment.
Generator (480i/1080i The Horizontal 100% Color Bar When the adjustment is over, 'ADC RGB 1080P Success’
Pattern adjust to within 0.7±0.1Vp-p) is displayed.
(6) Readjust after confirming the case Pattern or adjustment
condition where the adjustment errors.
Error massage is ‘Component1 Not Connected’ or ‘Not
Valid Format’ or ‘Check Signal Status’.
(7) After adjustment is complete, exit the adjustment mode by
pressing the ADJ KEY.
Copyright © 2007 LG Electronics. Inc. All right reserved. - 7 - LGE Internal Use Only
Only for training and service purposes
ADJUSTMENT INSTRUCTIONS
5-2. EDID DATA for PA75C : EDID for HDMI-3 (DDC (Display Data Channel) Data)
: EDID for HDMI-1 (DDC (Display Data Channel) Data) EDID table =
EDID table = 0 1 2 3 4 5 6 7 8 9 A B C D E F
0 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01
0 1 2 3 4 5 6 7 8 9 A B C D E F
10 00 11 01 03 80 73 41 96 0A CF 74 A3 57 4C B0 23
0 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01
20 09 48 4C AF CF 00 31 40 45 40 61 40 81 80 A9 40
10 00 11 01 03 80 73 41 96 0A CF 74 A3 57 4C B0 23
30 01 01 01 01 01 01 66 21 50 B0 51 00 1B 30 40 70
20 09 48 4C AF CF 00 31 40 45 40 61 40 81 80 A9 40
40 36 00 C4 8E 21 00 00 1E 02 3A 80 18 71 38 2D 40
30 01 01 01 01 01 01 66 21 50 B0 51 00 1B 30 40 70
50 58 2C 45 00 C4 8E 21 00 00 1E 00 00 00 FD 00 30
40 36 00 C4 8E 21 00 00 1E 02 3A 80 18 71 38 2D 40
60 58 1F 64 11 00 0A 20 20 20 20 20 20 00 00 00 FC
50 58 2C 45 00 C4 8E 21 00 00 1E 00 00 00 FD 00 30
70 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 8A
60 58 1F 64 11 00 0A 20 20 20 20 20 20 00 00 00 FC
70 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 8A 0 1 2 3 4 5 6 7 8 9 A B C D E F
0 02 03 16 F1 47 84 05 03 02 20 22 10 23 15 07 50
0 1 2 3 4 5 6 7 8 9 A B C D E F
10 65 03 0C 00 30 00 01 1D 00 72 51 D0 1E 20 6E 28
0 02 03 16 F1 47 84 05 03 02 20 22 10 23 15 07 50
20 55 00 C4 8E 21 00 00 1E 01 1D 80 18 71 1C 16 20
10 65 03 0C 00 10 00 01 1D 00 72 51 D0 1E 20 6E 28
30 58 2C 25 00 C4 8E 21 00 00 9E 8C 0A D0 8A 20 E0
20 55 00 C4 8E 21 00 00 1E 01 1D 80 18 71 1C 16 20
40 2D 10 10 3E 96 00 C4 8E 21 00 00 18 8C 0A D0 8A
30 58 2C 25 00 C4 8E 21 00 00 9E 8C 0A D0 8A 20 E0
50 20 E0 2D 10 10 3E 96 00 13 8E 21 00 00 18 26 36
40 2D 10 10 3E 96 00 C4 8E 21 00 00 18 8C 0A D0 8A
60 80 A0 70 38 1F 40 30 20 25 00 C4 8E 21 00 00 1A
50 20 E0 2D 10 10 3E 96 00 13 8E 21 00 00 18 26 36
70 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 F0
60 80 A0 70 38 1F 40 30 20 25 00 C4 8E 21 00 00 1A
70 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 10
Copyright © 2007 LG Electronics. Inc. All right reserved. - 8 - LGE Internal Use Only
Only for training and service purposes
ADJUSTMENT INSTRUCTIONS
6. Adjustment of White Balance (1) Connect the set according to the internal pattern or HDMI
input in accordance with measuring device connection
6-1. Required Test Equipment diagram.
(1) Color Analyzer : CA-210 (CH 9) (2) Set the Baud Rate of RS-232C to 115200. It is set to
=> To adjust color temperature of PDP, CS-1000 is the 115200 as default.
Color Analyzer(CA-210) and should be set to use CH 9 (3) Connect the RS-232C Cable to the set.
in which white, red, green, and blue color are corrected. (4) Connect the HDMI Cable to the set. (Limited to the set with
Conduct the adjustment according to the coordinates for HDMI option)
White Balance adjustment in the table below. (5) Select and adjust the model applicable to PA75C chassis
from the adjuster.
(2) Computer for adjusting (necessary for the automatic
adjustment, possible to communicate with the RS-232C, [RS-232C command used for the automatic adjustment]
Baud Rate : 115200) RS-232C COMMAND Meaning
(3) Video Signal Generator MSPG-925F 720p, 216Gray
[CMD ID DATA]
(Model :217, Pattern 78)
wb 00 00 White Balance Adjustment Start
6-2. Connection Diagram of Equipment wb 00 10 Gain Adjustment Start(Internal white pattern)
for Measuring (Automatic Adjustment) wb 00 1f Gain Adjustment End
wb 00 20 Offset Adjustment Start(Internal white pattern)
wb 00 2f Offset Adjustment End
(internal pattern) wb 00 ff White Balance Adjustment End
(Disappear Internal pattern)
Ô Jb 00 c0
Ô ...
[Adjustment Map]
6-3. White Balance Adjustment Method G Gain Jh Jb Je 00 187 183 159 192
Basically it uses the internal pattern but when internal pattern B Gain Ji Jc Jf 00 192 161 95 192
is not possible, you can select HDMI input for adjustment.
Through the option at the most bottom part of the Ez Adjust R Cut 64 64 64 127
Menu 7.White Balance menu, you can select NONE, INNER
G Cut 64 64 64 127
and HDMI, and the default is set to INNER. When the
adjustment cannot be done with the internal pattern, you can B Cut 64 64 64 127
select HDMI input for adjustment.
Copyright © 2007 LG Electronics. Inc. All right reserved. - 9 - LGE Internal Use Only
Only for training and service purposes
ADJUSTMENT INSTRUCTIONS
(2) Enter the ‘Ez - Adjust’ by pressing the ADJ on the Service
R/C.
(3) Select 10.TEST PATTERN using the CH + / - KEY and
press the Enter KEY to execute a heat run for more than
30 minutes.
(4) Execute a Zero Calibration for CA-210 and put it at
distance of less than 10Cm from the PDP module surface
center during the adjustment.
(5) Select ‘7. White-Balance’ of ‘Ez - Adjust’ by pressing the
ADJ KEY on the Service R/C. Then enter adjustment mode
by pressing the Right KEY (G) .
(The internal pattern of full white appears by pressing G)
(6) The adjustment is conducted in three levels of color
temperature; COOL, MEDIUM, and WARM.
Copyright © 2007 LG Electronics. Inc. All right reserved. - 10 - LGE Internal Use Only
Only for training and service purposes
Block Diagram - Overview
AGC CTL (From BCM)
DDR(128MB)
DDR(128MB)
X-tal(54M) Flash
IF(AT)
AT/NT DDR(64MB)
DDR(64MB)
(16MB)
Tuner
- 11 -
SDA
SCL EEPROM
BCM3553
To Micom I2S
Audio NTP3000
Dual DSP (Digital AMP)
TMDS341A
HDMI HDMI
BLOCK DIAGRAM
- 12 -
RGB_B RGB Input
RGB_R DVO Out[0:29]
H Sync
RGB H_Sync
V Sync 74F08D
RGB V_Sync
BLOCK DIAGRAM
- 13 -
+5V Power_1 TMDS RX2+/-
Out Input
Hot Plug Detect_1 TMDS RXCLK+/-
INPUT
I2S_CLK_IN/DATA_IN
RESET SPK R
- 14 -
I2S_CLK_OUT OUT1A/B
ANA L/R OP AMP ANA L/R OUT I2S_CLK_OUT/
I2S_DATA_OUT DATA_OUT/
[MC33078] (CS5340) I2S_LR_OUT LRCH OUT PWM MODULATOR/
POWER AMP
(NTP3000)
[NTP3000] SPK L
BLOCK DIAGRAM
[L2 / R2]
Decoder
AV2_Audio
Switch
Switch MPEG2
RGB_Audio [L3 / R3]
HDMI Rx
Comp1_Audio [L4 / R4] [Rout/Lout] I2C SCL/SDA Dolby Built in
Comp2_Audio [L5 / R5] AUDIO Internal
I2S/SPDIF
Processor Convert
BCM3553 4.7K‰
Address
I2C0_5V
I2C_Channel 0 ATSC/NTSC Tuner 0xC2
5.0V
LM57(DS1621) 0x94
- 15 -
CAT6431 Ready
(only S/W mode)
BLOCK DIAGRAM
NVRAM 0xA6
3.3V
1K‰ 0xD4
I2C2_3.3V I2C2_2.5V
I2C_Channel 2 PDP MODULE 0x1C
3.3VST
4.7K‰
NTP3000 0x54
I2C3_3.3V
MTV416 0x50
I2C_Channel 3
Speaker R/L
- 16 -
+12.0V
+12.0V LCD control B/D FAN
IC806 +9V
BLOCK DIAGRAM
KA7809
IC500 IC504
TEA6420D MC33078 Digital eye
(Audio SW) (OP AMP)
IC901,902
KIA78R09F
(FAN REG)
FAN
IC202
IC404 +3.3VST_MICOM
AZ1117H-3.3
IC406 IC407
- 17 -
AT24C16AN MTV416GMF
(EEPROM) ( micom )
HDMI CEC
BIAS
BLOCK DIAGRAM
Inv/RL/live-on
3.3V->5V
BIAS
IC800 +5V_TU
+6.0V
+6.0V PQ05DZ1U
TUNER
IC801 +5.0V
PQ05DZ1U
- 18 -
BIAS
BCM PCI 단 IC600
Inv/RL/live-on EDID EEPROM
BCM SCL/SDA0~1 입력단자 HPD 3:1HDMI SW
3.3V->5V W/P SCL/SDA
BCM DS-AGC,AUD_VDD
BLOCK DIAGRAM
D3.3V_BCM
IC804
AZ1117H-3.3
IC401
IC101 74LVC14ADW
BCM3553 Reset SW
Flash MEM 32M Reset 슈미트트리거
A3.3V_BCM
BCM3553 BOOT
DAC/USB,AGC,HDMI STRAP
3.3V_TMDS_SW IC600
IC802
PICHDMI341
AZ1117H-3.3 HDMI 3:1 SW
+3.3V
+3.3V
IC200,201 IC501 IC502 IC503
JK501
BIAS
IC407
MTV416GMF LVDS Tuner CTR
+3.3V detect signal
IC300,301,302,303
Power_CTL_2.6V_1.2V BCM3553
DDR IC 전원
- 19 -
DDR0_VTT
IC304 DDR0_REF
DDR Memory
5C25955TR
BLOCK DIAGRAM
A2.6V_BCM
BCM3553
D1.2V_BCM
IC805 A1.2V_BCM
BCM3553
SC4519STRT
DC-DC converter
Power_CTL_2.6V_1.2V
IC501
IC807 +1.8V_NTP
NTP3000
AZ1117H-1.8
(sound IC)
300
601
602
600
306
603
120 LV1
301
560
570
304
302
200
303
205 206
590
501 202
204
250
520 201
203
400
240
502
A2
900
901
Copyright © 2007 LG Electronics. Inc. All right reserved. - 20 - LGE Internal Use Only
Only for training and service purposes
Copyright © 2007 LG Electronics. Inc. All right reserved. LGE Internal Use Only
Only for training and service purposes
Copyright © 2007 LG Electronics. Inc. All right reserved. LGE Internal Use Only
Only for training and service purposes
Copyright © 2007 LG Electronics. Inc. All right reserved. LGE Internal Use Only
Only for training and service purposes
MAIN(TOP) CONTROL(TOP)
CONTROL(BOTTOM)
SIDE A/V(TOP)
SIDE A/V(BOTTOM)
Copyright © 2007 LG Electronics. Inc. All right reserved. LGE Internal Use Only
Only for training and service purposes
Dec., 2007
P/NO : MFL39961603 Printed in Korea