Documente Academic
Documente Profesional
Documente Cultură
®
www.unifiedalloys.com 1
MANUFACTURING STANDARD
FOR STAINLESS STEEL GAUGE PIPING
Material Welding
All pipes and fittings are manufactured from stainless steel sheet or plate to ASTM Welding procedures, welders and welding operators meet the requirements of
A-240 standards. Material 10 gauge (3.6 mm) and lighter will have No. 2D or better ASME Code Sec. IX. Welding procedures are carefully established and tested to
finish; material 3/16” (4.8 mm) and heaveier will have No. 1 finish. achieve full penetration welding.
Type of stainless steel shall be specified by the customer. The longitudinal welds in pipes and fittings are made either by the automatic
GTAW with or without filler metal, the automatic GMAW (spray transfer) or the
automatic plasma arc welding process. Gas backup protection is provided in all
ASTM Standards cases.
Pipe and fittings to ASTM standards A-778, A-774, A-358 HT-O and A-409 HT-O
can be supplied on request. The circumferential welds in fittings and assemblies are made by GTAW and/
or SMAW processes. Where the internal surface is not accessible for welding,
the root pass is welded from outside using GTAW while the internal surface is
ANSI-B31.1 and B31.3 Codes protected with flux.
Whenever pipes, fittings or piping assemblies are required to meet these Codes,
the purchase order must indicate the applicable code, the complete design data, The consumables are of a grade similar to the base material and always of the
the type of service and the status of registration with Provincial Authorities. extra low carbon grade. Weld reinforcement does not exceed 0.063” (1.5 mm)
at the inside surface and 0.094” (2.4 mm) at the outside surface. Surface finish
In such cases, design, fabrication, examination and inspection of piping of welds is left as welded. However, grinding and polishing can be done upon
assemblies and sub-assemblies will meet the requirements of ANSI-B31.1 or request.
B31.3 as applicable. All welding will comply with ASME Code Sec. IX.
Some of the fittings illustrated in this catalogue have been designed for Non-Code Cleaning
applications. For complete information on the pressure rating of fittings for Code All pipes and fittings are pickled in an acid solution and rinsed thoroughly with
application and the provinces in which they are registered, please contact our clean water. Piping assemblies can be acid washed upon request.
representative.
Whenever specified in the purchase order, piping assemblies will be hydro-
Inspection
statically tested. Such test will be witnessed by the Authorized Provincial Inspector.
Our aim is to produce a good quality product. To this end, tools, dies, jigs and
The quality control system used during fabrication of straight pipes, fittings and fixtures used throughout the manufacturing process are periodically inspected in
piping assemblies to the above Codes has been approved by the Provincial order to ensure that dimensional tolerances are observed. All pipes, fittings and
Authorities having jurisdiction. assemblies are visually inspected and random radiographic examination of welds
is undertaken to the extent necessary to ensure good quality welding.
Pressure Rating Piping assemblies are inspected for dimensional accuracy. Tolerance will conform
Pressure ratings of pipe and fittings are shown on pages 17 and 18. to spooling manufacturing tolerance as shown on page 4.
Facilities are available for more extensive testing, inspection and quality control.
2
TOLERANCES OF GAUGE PIPE AND FITTINGS
90° Ells, Reducers,
Size of Pipe 45° Ells,
All Pipe and Fittings Stub Ends, Backing Rings Squareness & Angle
or Fitting Laterals,
Tee’s, Y’s Connectors Ovality at
Wall Concentric Welding Ends
O.D. at Centre to Overall O.D.
mm In thickness at Bolt Circle I.D. to A B
Welding End End. Dim. Length I.D.
Welding End Bolt Circle
38 1-1/2
51 2 ± 1/32” ± 1/16” ± 1/16” 1/32” 1/16”
64 2 (± 1 mm) (± 2 mm) (± 2 mm) (1 mm) (2 mm) ± 1/16”
I.D. & I.P.S. Piping: Not less than 87.5% of nominal thickness.
76 3 (± 2 mm)
102 4
152 6 + 1/16” + 1/8” ± 1/16” ± 1/16” 1/16” 1/8” ± 3/32”
– 1/32”
203 8 (+ 2 mm) –0 (2 mm) (3 mm) (± 2.5 mm)
(– 1 mm)
254 10 ± 3/32” ± 3/32” (± 3mm) (± 2mm) (± 2 mm) 3/32” 3/16” ± 1/8”
+ 3/32”
305 12 – 1/32” (± 2.5 mm) (± 2.5 mm) (2.5 mm) (5 mm) (± 3 mm)
356 14 (± 2.5 mm) 3/32” 1/4” ± 5/32”
(– 1 mm)
406 16 (2.5 mm) (7 mm) (± 4 mm)
457 18 ± 1/8” ± 1/8” 1/8” 3/8”
508 20 (3 mm) (10 mm) ± 3/16”
610 24 ± 1/8” (± 3 mm) (± 3 mm) (± 5 mm)
– 1/32”
762 30 (+ 3 mm) 3/16” 3/8”
( – 1 mm)
914 36 ± 1/4”
1016 40 3/16” 1/2” (± 7 mm)
(5 mm) (13 mm)
Note:
1. Other tolerance requests from customers will be considered.
2. Pressed van-stones and pressed stub-ends; wall thickness
reduction may be greater than the tolerance shown above.
3. Tolerance on piping assemblies will generally conform to
spooling manufacturing tolerance shown on page E-4.
®
www.unifiedalloys.com 3
SPOOLING MANUFACTURING TOLERANCE
Pipe Diameter
4
I.D. GAUGE PIPE
GAUGE
14 12 11 10 7 3
INSIDE DIAMETER
WALL WALL WALL WALL WALL WALL
.078” 2.0 mm .109” 2.8 mm .125” 3.2 mm .140” 3.6 mm .188” 4.7 mm .250” 6.3 mm
Inches MM
LB/FT kg/m LB/FT kg/m LB/FT kg/m LB/FT kg/m LB/FT kg/m LB/FT kg/m
NOTES
1. Wall thickness tolerance to ASTM A 778. WALL
2. Material: Stainless steel 304L - 316L - 317L. Other alloys available upon request
3. For maximum working pressure see technical section. I.D.
4. Diameters & thickness other than shown available on request.
®
www.unifiedalloys.com 5
I.D. SMOOTH-FLOW GAUGE ELBOWS
90° 45°
Inside. Wall U.S.S. Weight Inside. Wall U.S.S. Weight
A B
Dia. Thickness Gauge (Lb/Ln.Ft.) Dia. Thickness Gauge (Lb/Ln.Ft.)
1-1/2 0.078 14 2-1/4 0.4 1-1/2 0.078 14 15/16 0.2
0.125 11 2-1/4 0.4 0.125 11 15/16 0.2
2 0.078 14 3 0.6 2 0.078 14 1-1/4 0.4
0.125 11 3 1.2 0.125 11 1-1/4 0.6
2-1/2 0.078 14 3-3/4 1.1 2-1/2 0.078 14 1-9/16 0.6
0.125 11 3-3/4 1.7 0.125 11 1-9/16 0.9
3 0.078 14 4-1/2 1.6 3 0.078 14 1-7/8 0.8
0.125 11 4-1/2 2.5 0.125 11 1-7/8 1.2
4 0.078 14 6 3.0 4 0.078 14 2-1/2 1.5
0.125 11 6 4.6 0.125 11 2-1/2 2.3
5 0.078 14 7-1/2 4.1 5 0.078 14 3-1/8 2.0
0.125 11 7-1/2 6.6 0.125 11 3-1/8 3.3
6 0.078 14 9 6.0 6 0.078 14 3-3/4 3.0
0.125 11 9 9.9 0.125 11 3-3/4 4.9
8 0.078 14 12 10.6 8 0.078 14 5 5.3
0.125 11 12 17.0 0.125 11 5 8.5
10 0.109 12 15 23.0 10 0.109 12 6-1/4 11.5
0.125 11 15 26.7 0.125 11 6-1/4 13.5
12 0.109 12 18 34.6 12 0.109 12 7-1/2 17.3
0.125 11 18 38.3 0.125 11 7-1/2 19.2
14 0.125 11 21 52.5 14 0.125 11 8-3/4 26.3
0.187 3/16 21 77.5 0.187 3/16 8-3/4 38.8
16 0.125 11 24 68.0 16 0.125 11 10 34.0
0.187 3/16 24 101.0 0.187 3/16 10 50.5
18 0.125 11 27 96.4 18 0.125 11 11-1/4 48.2
0.187 3/16 27 128.0 0.187 3/16 11-1/4 64.0
0.250 1/4 27 171.0 0.250 1/4 11-1/4 85.5
20 0.140 11 30 121.0 20 0.140 11 12-1/2 60.5
0.187 3/16 30 158.0 0.187 3/16 12-1/2 79.0
0.250 1/4 30 211.0 0.250 1/4 12-1/2 105.0
24 0.187 3/16 36 234.0 24 0.187 3/16 15 117.0
0.250 1/4 36 312.0 0.250 1/4 15 156.0
All dimensions in inches
®
www.unifiedalloys.com 7
I.D. PRESSED VAN-STONES
8
I.D. ROLLED VAN-STONES
A B C T
3 4-1/2 3/4 1/8 0.6
4 6 1 1/8 0.8
5 7 1 1/8 1.0
6 8 1 1/8 1.5
8 10-1/2 1-1/4 1/8 2.4
10 13 1-1/2 1/8 3.7
12 15 1-1/2 1/8 4.3
14 17 1-1/2 1/8 5.0
16 19 1-1/2 3/16 8.4
18 21 1-1/2 3/16 9.4
20 23 1-1/2 3/16 10.3
24 28 2 3/16 15.8
24 28 2 1/4 21.0
30 34 2 1/4 25.7
36 40 2 1/4 31.4
Material: Stainless steel angle types 304, 304L, 316 and 316L.
Recommended max. working pressure:
Up to 24” dia.: 150 PSI at 200°F.
®
30” and 36” dia.: 125 PSI at 200°F.
www.unifiedalloys.com 9
BACKING FLANGES (FOR I.D. GAUGE PIPE)
Material: ASTM 285-C or equal for T1 and T2. SA 516-70 or equal for T3.
Drilling: To ANSI B16.1 class 125.
Finish: Metal primer or galvanized.
Note: Backing flanges in T3 series are not stocked in sizes 8” and over.
T1 and T2 thicknesses do not comply with ANSI B31.1 and B31.3.Cald
10
I.D. SLIP ON BACKING FLANGES
Outside Inside
I.D. of Weight
Dia. Dia.
Pipe
O.D. I.D. T A B C T
3 7-1/2 3-7/8 3/4 6 4 3/4 7.1
4 9 4-7/8 3/4 7-1/2 8 3/4 9.5
5 10 5-7/8 3/4 8-1/2 8 7/8 10.7
6 11 6-7/8 3/4 9-1/2 8 7/8 12.3
8 13-1/2 8-7/8 3/4 11-3/4 8 7/8 17.7
10 16 11 1 14-1/4 12 1 30.2
12 19 13 1 17 12 1 43.5
14 21 15 1-1/8 18-3/4 12 1-1/8 55
16 23-1/2 17 1-1/8 21-1/4 16 1-1/8 66
18 25 19-1/4 1-1/4 22-3/4 16 1-1/4 81.4
20 27-1/2 21-3/8 1-1/4 25 20 1-1/4 86.3
24 32 25-3/8 1-3/8 29-1/2 20 1-3/8 121
30 39 31-3/4 1-1/2 36 28 1-3/8 176
36 46 37-3/4 1-1/2 42-3/4 32 1-5/8 237
42 53 43-3/4 1-3/4 49-1/2 36 1-5/8 339
48 59-1/2 49-3/4 2 56 44 1-5/8 455
All dimensions in inches
®
www.unifiedalloys.com 11
CLAD BLIND FLANGES
Outside Bolt Circ.
Nominal Thickness Number Dia. of Weight
Dia. Dia.
Dia. T of Bolts Bolt Holes W
O.D. B.C.D.
1-1/2 5 3/4 3-7/8 4 5/8 4.3
2 6 3/4 4-3/4 4 3/4 6.2
2-1/2 7 3/4 5-1/2 4 3/4 8.5
3 7-1/2 3/4 6 4 3/4 9.8
4 9 3/4 7-1/2 8 3/4 14.0
5 10 3/4 8-1/2 8 7/8 17.6
6 11 3/4 9-1/2 8 7/8 21.3
8 13-1/2 3/4 11-3/4 8 7/8 32.2
10 16 1 14-1/4 12 1 58.0
12 19 1 17 12 1 83.1
14 21 1-1/8 18-3/4 12 1-1/8 113.0
16 23-1/2 1-1/8 21-1/4 16 1-1/8 142.0
18 25 1-1/4 22-3/4 16 1-1/4 179.0
20 27-1/2 1-1/4 25 20 1-1/4 217.5
24 32 1-3/8 29-1/2 20 1-3/8 323.0
30 38-3/4 1-1/2 36 28 1-3/8 530.0
36 46 1-1/2 42-3/4 32 1-3/8 755.0
All dimensions in inches
Blind Flanges are available from stock in galvanized mild steel with stainless steel 316, .078” thick cladding.
Also available upon request in solid stainless steel, primed mild steel, various types and thicknesses of cladding, flange thickness and diameter.
12
I.D. STUB-ENDS TYPE “B”
I.D.
Material: ASTM A240 types, 304, 304L, 316 and 316L.
Welding: Automatic Paw or GTAW with or without filler metal or GMAW.
All stub-ends are pickled and washed.
NOTE: FABRICATED IN INCHES.
®
www.unifiedalloys.com 13
IPS ANGLE COLLARS
ASTM A 774
Angle
Diameter A B Weight
Dimension
INCHES mm INCHES mm INCHES mm INCHES mm LB kg
3 75 3.5 89 3.56 90 3/4 x 3/4 x 1/8 16 x 19 x 3.2 0.5 0.2
4 100 4.5 114 4.56 116 1 x 1 x 1/8 25 x 25 x 3.2 0.8 0.4
5 125 5.56 141 5.62 143 1 x 1 x 1/8 25 x 25 x 3.2 1.0 0.5
1 x 1 x 1/8 25 x 25 x 3.2 1.5 0.7
6 150 6.62 168 6.75 171
1 x 1 x 3/16 25 x 25 x 4.8 2.2 1.0
*1-1/4 x 1-1/4 x 1/8 32 x 32 x 3.2 3.4 1.1
8 200 8.62 219 8.75 222
*1-1/4 x 1-1/4 x 3/16 32 x 32 x 4.8 3.6 1.6
*1-1/4 x 1-1/4 x 1/8 32 x 32 x 3.2 3.0 1.4
10 250 10.75 273 10.84 275
*1-1/4 x 1-1/4 x 3/16 32 x 32 x 4.8 4.5 2.0
1-1/2 x 1-1/2 x 1/8 38 x 38 x 3.2 4.3 1.9
12 300 12.75 324 12.84 326
1-1/2 x 1-1/2 x 3/16 38 x 38 x 4.8 6.5 2.9
1-1/2 x 1-1/2 x 1/8 38 x 38 x 3.2 5.0 2.3
14 350 14 356 14.09 358
1-1/2 x 1-1/2 x 3/16 38 x 38 x 4.8 7.0 3.2
1-1/2 x 1-1/2 x 3/16 38 x 38 x 4.8 8.0 3.6
16 400 16 406 16.09 409
1-1/2 x 1-1/2 x 1/4 38 x 38 x 6.3 10.5 4.7
1-1/2 x 1-1/2 x 3/16 38 x 38 x 4.8 9.0 4.1
18 450 18 457 18.09 460
1-1/2 x 1-1/2 x 1/4 38 x 38 x 6.3 12.0 5.4
1-1/2 x 1-1/2 x 3/16 38 x 38 x 4.8 10.2 4.6
20 500 20 508 20.12 511
1-1/2 x 1-1/2 x 1/4 38 x 38 x 6.3 13.5 6.1
2 x 2 x 3/16 51 x 51 x 4.8 15.7 7.5
24 600 24 610 24.12 613
2 x 2 x 1/4 51 x 51 x 6.3 21.0 9.5
2 x 2 x 1/4 51 x 51 x 6.3 26.0 11.8
30 750 30 762 30.12 765
2 x 2 x 3/8 51 x 51 x 9.5 39.0 17.7
2 x 2 x 1/4 51 x 51 x 6.3 31.0 14.1
36 900 36 914 36.12 918
2 x 2 x 3/8 51 x 51 x 9.5 46.5 21.1
NOTES
1. Material: Stainless steel 304L - 316L. Other alloys available upon request.
2. Available in other thicknesses & diameters.
3. For maximum working pressure see technical section.
*Sizes 8” & 10” - use 1” x 1” for slip-on type.
14
IPS BACKING FLANGES
SLIP-ON
3 4 5 6 8 10 12
75 100 125 150 200 250 300
7-1/2 9 10 11 13-1/2 16 19
190 229 254 279 343 407 483
4-1/8 5-1/8 6-1/8 7-1/4 9-1/4 11-3/8 13-3/8
105 130 156 184 235 289 340
5/8 5/8 5/8 5/8 5/8 5/8 3/4
15.9 15.9 15.9 15.9 15.9 15.9 19
3/4 3/4 3/4 3/4 3/4 1 1
19 19 19 19 19 25.4 25.4
3/4 3/4 3/4 3/4 7/8 1 1-1/4
19 19 19 19 22.2 25.4 31.7
4 8 8 8 8 12 12
NOTES
1. Material: T2, mild steel. T1, T3, A516 Gr. 70. upon request
2. Drilling: ASME B16.5 CL. 150.
®
www.unifiedalloys.com 15
MAXIMUM WORKING PRESSURE IPS PIPE & FITTINGS
TEMP: 200°F (100°C) MAX ASTM A 778 / ASTM A 774
Nominal Outside Nominal Wall Thickness Pipe & Reducers L.R. Elbows Mitred Elbows Tees Laterals
Diameter Diameter (See notes) One Reduction Smooth Flow L.R. (See notes) (See notes)
IN mm IN mm Gauge IN mm psi kPa psi kPa psi kPa psi kPa psi Kpa
14 0.078 2.0 505 3480 450 3105 380 2620 250 1725 155 1070
5S 0.083 2.1 535 3690 485 3345 405 2790 265 1825 165 1140
4 100 4.500 114 12 0.109 2.8 710 4895 640 4415 535 3690 355 2450 220 1515
10S 0.120 3.0 790 5445 710 4895 595 4105 390 2690 245 1690
11 0.125 3.2 825 5690 740 5100 620 4275 410 2825 255 1760
14 0.078 2.0 405 2790 365 2515 305 2105 200 1380 125 860
5S 0.109 2.8 570 3930 515 3550 425 2930 285 1965 175 1205
5 125 5.563 141
11 0.125 3.2 660 4550 595 4105 490 3380 325 2240 200 1380
10S 0.134 3.4 710 4895 640 4415 530 3655 350 2415 215 1480
14 0.078 2.0 340 2345 305 2105 260 1795 168 1160 105 725
5S 0.109 2.8 475 3275 430 2965 365 2515 235 1620 145 1000
6 150 6.625 168
11 0.125 3.2 550 3790 495 3415 420 2895 275 1895 170 1170
10S 0.134 3.4 590 4070 530 3655 450 3105 295 2035 180 1240
14 0.078 2.0 260 1795 230 1585 200 1380 125 860 80 550
5S 0.109 2.8 365 2515 325 2240 280 1930 180 1240 110 760
8 200 8.625 219
11 0.125 3.2 420 2895 375 2585 320 2205 210 1450 130 895
10S 0.134 3.4 450 3105 405 2790 345 2380 225 1550 140 965
12 0.109 2.8 290 2000 260 1795 225 1550 140 965 90 620
11 0.125 3.2 335 2310 300 2070 260 1795 160 1105 105 725
10 250 10.750 273
5S 0.134 3.4 360 2480 320 2205 275 1895 170 1170 110 760
10S 0.165 4.2 445 3070 400 2760 340 2345 215 1480 135 930
12 0.109 2.8 245 1690 220 1515 190 1310 115 795 75 515
11 0.125 3.2 280 1930 250 1725 220 1515 130 895 85 585
12 300 12.750 324
5S 0.156 4.0 350 2413 315 2170 275 1895 165 1140 110 760
10S 0.180 4.6 405 2790 365 2515 315 2345 195 1345 125 860
NOTES
1. Pressure ratings are limited to non-toxic, non-lethal, non-flammable liquids in non-cyclic
vibration-free service, and where ASME B31 piping codes are not applicable.
2. Thickness tolerance to ASTM A 778 and A 774.
16
MAXIMUM WORKING PRESSURE IPS PIPE & FITTINGS
TEMP: 200°F (100°C) MAX ASTM A 778 / ASTM A 774
Nominal Outside Nominal Wall Thickness Pipe & Reducers L.R. Elbows Mitred Elbows Tees Laterals
Diameter Diameter (See notes) One Reduction Smooth Flow L.R. (See notes) (See notes)
IN mm IN mm Gauge IN mm psi kPa psi kPa psi kPa psi kPa psi Kpa
11 0.125 3.2 255 1760 230 1585 200 1380 120 825 80 550
10 0.140 3.6 285 1965 255 1760 225 1550 135 930 90 620
14 350 14.000 356
5S 0.156 4.0 320 2205 285 1965 255 1760 150 1035 100 690
10S 0.188 4.8 385 2605 350 2415 305 2105 185 1275 120 825
11 0.125 3.2 220 1515 200 1380 175 1205 95 655 65 450
10 0.140 3.6 250 1725 225 1550 200 1380 110 760 70 485
16 400 16.000 406
5S 0.165 4.2 295 2035 265 1825 235 1620 128 885 85 585
10S 0.188 4.8 335 2310 305 2105 265 1825 145 1000 95 655
11 0.125 3.2 195 1345 175 1205 155 1070 85 585 50 345
10 0.140 3.6 220 1515 200 1380 175 1205 95 655 60 415
18 450 18.000 457
5S 0.165 4.2 260 1795 235 1620 205 1415 115 795 70 485
10S 0.188 4.8 300 2070 270 1860 235 1620 130 895 80 550
10 0.140 3.6 200 1380 180 1240 160 1105 85 585 55 380
5S 0.188 4.8 268 1850 240 1655 215 1480 115 795 75 515
20 500 20.000 508
10S 0.218 5.5 310 2135 280 1930 245 1690 135 930 85 585
1/4 0.250 6.4 360 2480 325 2240 285 1965 155 1070 100 690
10 0.140 3.6 165 1140 150 1035 130 895 60 415 40 275
3/16 0.188 4.8 225 1550 200 1380 175 1205 85 585 55 380
24 600 24.000 611
5S 0.218 5.5 260 1795 235 1620 205 1415 110 690 65 450
10S 0.250 6.4 300 2070 270 1860 235 1620 115 795 75 515
3/16 0.188 4.8 180 1240 160 1105 140 965 75 515 35 240
30 750 30.000 762 5S 0.250 6.4 235 1620 215 1480 190 1310 100 690 45 310
10S 0.312 7.9 295 2035 270 1860 235 1620 125 860 60 415
1/4 0.250 6.4 195 1345 175 1205 155 1070 80 550 50 345
36 900 36.000 914
5/16 0.312 7.9 245 1690 220 1515 195 1345 105 725 65 450
NOTES
1. Pressure ratings are limited to non-toxic, non-lethal, non-flammable liquids in non-cyclic
vibration-free service, and where ASME B31 piping codes are not applicable.
2. Thickness tolerance to ASTM A 778 and A 774.
®
www.unifiedalloys.com 17
ASTM A 774 IPS ELBOWS
SCH 5S AND 10S
IN mm IN mm Sch. IN mm IN mm IN mm LB kg LB kg
5S 0.083 2.1 1.8 0.8 0.9 0.4
3 75 3.5 89 4.5 114 2 51
10S 0.120 3.0 2.7 1.2 1.4 0.6
5S 0.083 2.1 3.2 1.4 1.6 0.7
4 100 4.5 114 6 152 2.5 63
10S 0.120 3.0 4.6 2.1 2.3 1.0
5S 0.109 2.8 9.0 4.1 4.5 2.0
6 150 6.62 168 9 229 3.75 95
10S 0.134 3.4 11.2 5.1 5.6 2.5
5S 0.109 2.8 16.0 7.3 8.0 3.7
8 200 8.62 219 12 305 5 127
10S 0.148 3.7 21.5 9.7 10.7 4.9
5S 0.134 3.4 31.5 13.8 15.2 6.9
10 250 10.75 273 15 381 6.25 159
10S 0.165 4.2 37.0 17.0 18.8 8.5
5S 0.155 4.0 50.0 22.9 25.0 11.5
12 300 12.75 324 18 457 7.5 190
10S 0.180 4.6 58.0 26.4 29.0 13.2
5S 0.154 4.0 64.0 29.0 32.0 14.5
14 350 14.0 356 21 533 8.75 222
10S 0.188 4.8 80.0 36.3 40.0 18.2
5S 0.165 4.2 89.0 40.4 44.0 20.2
16 400 16.0 406 24 610 10 254
10S 0.188 4.8 114.0 47.2 57.0 23.6
5S 0.165 4.2 114.0 51.7 57.0 25.8
18 450 18.0 457 27 686 11.25 286
10S 0.188 4.8 130.0 59.4 66.0 29.7
5S 0.188 4.8 160.0 72.6 80.0 36.3
20 500 20.0 508 30 762 12.5 317
10S 0.216 5.5 190.0 83.9 92.0 41.9
5S 0.218 5.5 267.0 121.0 133.0 60.5
24 600 24.0 610 36 914 15 381
10S 0.250 6.3 306.0 139.0 153.0 69.5
NOTES
1. Wall thicknesses are nominal.
2. Material: Stainless steel 304L - 316L. Other alloys available upon request.
3. For maximum working pressure see technical section.
18 Wall Wall
O.D. O.D.
CLEAN-OUT (I.D. AND N.P.S.) CLEAN-OUT (I.D. AND N.P.S.)
PLUG TYPE QUICK-OPENING TYPE
The cover of this type of clean-out is provided with snugly fitting plug. Quick opening clean-out as shown was introduced by Douglas Bros. several years
ago, and since then, thousands have been installed in Paper Mills.
The inside of the pipe, with plug in place, provides smooth bore eliminating stock
hang-up. It is ideally suited for welding at the end of the pipe-run or on elbows, providing
quick and easy access for inspection and cleaning.
Material: ASTM A-240 types 304L and 316L (stub and plug). 150 6 238 9-3/8 9.1 20
200 8 267 10-1/2 12.7 28
250 10 336 13-1/4 15.5 34
300 12 371 14-5/8 20.0 44
®
www.unifiedalloys.com 19
DIAMOND CLEAN-OUT AND INSPECTION PORT
Size
in mm For Installation In
6 150 6”90° and 45° Long Sweep Elbows (150 mm)
8 200 8”90° and 45° Long Sweep Elbows (200 mm)
10 250 10”90° and 45° Long Sweep Elbows (250 mm)
20
DIAMOND CLEAN-OUT AND INSPECTION PORT
For Installation In Manufactured From Type 316 Stainless Steel
Size 90° ELLs 45° ELLs Reducers Tube & Pipe The Clean-out Consists of the Following Parts:
*4 Fits 4 4 6 6 • Safety chain to prevent loss of components.
6 Fits 6 6 8 & 10 8 & 10
• Nickel bronze wing nut to ensure easy operation and prevent galling of
8 Fits 8 8 12 thru 16 12 thru 16 thread.
10 Fits 10 10 18 thru 22 18 thru 22 • Nickel bronze cast yoke.
12 Fits 21 thru 18 12 thru 18 24 & Larger 24 & Larger
• Stainless steel cover and stud complete with neoprene “O” ring.
* 4” size requires special trimming on all items except 4” tube size elbows. • Stainless steel mounting frame.
May we suggest you let Douglas install when possible.
Note: 12” size also fits tanks and vessels. For Installation In
Size 90° ELLs 45° ELLs Reducers Tube & Pipe
Installation Instructions 100 mm 100 100 150 150
150 mm 150 150 200 & 250 200 & 250
• Remove the cover from the frame. Place frame in position on pipe and
mark the outside contour. Cut desired opening approximately 1/4” inside 200 mm 200 200 300 to 400 300 to 400
line and tack weld the frame in position. 250 mm 250 250 450 to 550 450 to 550
• Heliarc weld inside and grind weld smooth. Weld the outside of the frame, 300 mm 300 to 450 300 to 450 600 & larger 600 & larger
let cool and insert cover.
Approximate opening all sizes 4-3/4” x 2-3/4” (120 mm x 70 mm)
• Cover must be removed to prevent damage to O ring during welding.
Approximate shipping weight 6 pounds (2.7 kg).
• Note: Clean-outs are designed for installation in 90° ELLs and therefore
require slight dressing when installing in straight pipe, reducers, tanks or
vessels.
www.unifiedalloys.com 21
PIPE REINFORCING FOR FULL VACUUM SERVICE @ 200°C.
STAINLESS STEEL I.D. PIPE
22
UNIFIEDALLOYS I. D. PIPE
ASTM A 778
GAUGE / JAUGE
INSIDE DIA. 14 12 11 10 7 3
DIA. INTÉRIEURE WALL / MUR WALL / MUR WALL / MUR WALL / MUR WALL / MUR WALL / MUR
INCHES .078" 2.0 mm .109" 2.8 mm .125" 3.2 mm .140" 3.6 mm .188" 4.7 mm .250" 6.3 mm
mm LB/FT LB/FT LB/FT LB/FT LB/FT LB/FT
POUCES kg/m kg/m kg/m kg/m kg/m kg/m
LB/PI LB/PI LB/PI LB/PI LB/PI LB/PI
NOTES
1. Wall thickness tolerance to ASTM A 778.
2. Material: Stainless steel 304L - 316L - 317L.
Other alloys available upon request.
3. For maximum working pressure
see technical section.
4. Diameters & thicknesses other than
shown available on request.
23
I.D. ELBOWS
UNIFIEDALLOYS ASTM A 774
NOTES
1. Wall thickness tolerance to ASTM A 774. 1. Tolérance des murs selon ASTM A 774.
2. Material: Stainless steel 304L - 316L - 317L. 2. Matériau: acier inoxydable 304L - 316L -
Other alloys available upon request. 317L.
Autres alliages disponibles sur demande.
3. For maximum working pressure 3. Pour pression maximale
see technical section. voire section technique.
4. Diameters & thicknesses other than 4. Diamètres et epaisseurs autres que
shown available on request. montrés, disponibles sur demande.
24
I.D. MITRED ELBOWS
UNIFIEDALLOYS I.D. REDUCERS
ASTM A 774
INSIDE DIA.
A B C D
DIA. INTÉRIEUR
INCHES INCHES INCHES INCHES INCHES
mm mm mm mm mm
POUCES POUCES POUCES POUCES POUCES
1½ 38 6 152 4 102 2¼ 57 4½ 114
2 51 6½ 165 4½ 114 2½ 64 5 127
2½ 64 7 178 5 127 3 76 5½ 140
3 76 7¾ 197 5½ 140 3 76 6 152
4 102 9 229 6½ 165 4 102 7 178
5 127 10 ¼ 260 7½ 191 4½ 114 8 203
6 152 11 ½ 292 8 203 5 127 9 229
8 203 14 356 9 229 5½ 140 11 279
10 254 16 ½ 419 10 279 6½ 165 12 305
12 305 19 483 11 305 7½ 191 14 356
14 356 21 ½ 546 12 356 7½ 191 16 406
16 406 24 610 15 381 8 203 18 457
18 457 26 ½ 673 16 ½ 419 8½ 216 19 483
20 508 29 737 18 457 9½ 241 20 508
24 610 34 864 22 559 11 279 24 610
30 762 41 ½ 1054 25 635 15 381 30 762
36 914 49 1245 28 711 18 457 36 914
NOTES
1. Wall thickness tolerance to ASTM A 774. 1. Tolérance des murs selon ASTM A 774.
2. Material: Stainless steel 304L - 316L - 317L. 2. Matériau: acier inoxydable 304L - 316L -
Other alloys available upon request. 317L.
Autres alliages disponibles sur demande.
3. For maximum working pressure 3. Pour pression maximale
see technical section. voir section technique.
4. Available in same thickness as pipe. 4. Disponible dans les mêmes épaisseurs que
le tuyau.
25
I.D. FITTINGS
UNIFIEDALLOYS ASTM A 774
TEE / TÉ &
INSIDE DIA. CROSS / LATERAL / LATÉRAL WYE / Y
CROIX
DIA. INTÉRIEUR A B C D E F
INCHES INCHES INCHES INCHES INCHES INCHES INCHES
mm mm mm mm mm mm mm
POUCES POUCES POUCES POUCES POUCES POUCES POUCES
NOTES
1. Wall thickness tolerance to ASTM A 774. 1. Tolérance des murs selon ASTM A 774.
2. Material: Stainless steel 304L - 316L - 317L. 2. Matériau: acier inoxydable 304L - 316L -
Other alloys available upon request. 317L.
Autres alliages disponibles sur demande.
3. For maximum working pressure 3. Pour pression maximale
see technical section. voir section technique.
4. Available in same thickness as pipe. 4. Disponible dans les mêmes épaisseurs que
le tuyau.
26
UNIFIEDALLOYS I.D. BACKING FLANGES
SI UNITS UNITÉS SI
DIA. O.D. I.D. WEIGHT / POIDS
T1 T2 T3 A B C
(NOM.) D.E. D.I. T1 T2 T3
38 127 51 15.9 19.0 19.0 98 4 15.9 1.4 1.6 1.6
50 152 63 15.9 19.0 19.0 121 4 19.0 1.8 2.1 2.1
64 178 76 15.9 19.0 19.0 140 4 19.0 2.4 2.8 2.8
76 191 92 15.9 19.0 19.0 152 4 19.0 2.7 3.2 3.2
102 229 117 15.9 19.0 19.0 190 8 19.0 3.6 4.3 4.3
127 254 143 15.9 19.0 19.0 216 8 22.2 4.0 4.9 4.9
152 279 168 15.9 19.0 19.0 241 8 22.2 4.7 5.6 5.6
203 343 219 15.9 19.0 22.2 298 8 22.2 6.7 8.0 9.4
254 407 273 19.0 25.4 25.4 362 12 25.4 8.6 13.7 13.7
305 483 324 19.0 25.4 31.7 432 12 25.4 14.8 19.7 24.7
356 534 375 19.0 28.6 31.7 476 12 28.6 16.6 25.0 35.7
406 597 425 19.0 28.6 38.1 540 16 28.6 20.0 29.9 40.1
457 635 476 25.4 31.7 38.1 578 16 31.7 22.1 36.9 44.4
508 699 530 25.4 31.7 41.2 635 20 31.7 31.3 39.1 50.9
610 813 632 25.4 34.9 51.0 749 20 34.9 39.9 44.9 80.2
762 985 787 25.4 38.1 60.3 914 28 34.9 53.1 79.8 126.7
914 1169 940 25.4 38.1 73.0 1086 32 41.3 71.7 107.5 206.5
NOTES
1. Material: T1, T2 mild steel, T3 A516 Gr. 70 1. Matériau: T1, T2 acier doux, T3 A516 Gr. 70
2. Drilling: ASME B16.5 CL. 150 2. Perçage: ASME B16.5 CL. 150
3. For maximum working pressure 3. Pour pression maximale
see technical section. voir section technique.
4. Finish: Galvanized 4. Fini: Galvanisé
5. T1 available on request only 5. Epaisseur T1 sur demande seulement.
27
UNIFIEDALLOYS BLIND FLANGES
SI UNITS UNITÉS SI
DIA. O.D. NO. OF HOLES DIA. OF HOLES WEIGHT (kg)
T5 A B
(NOM.) D.E. NB. DE TROUS DIA. DES TROUS POIDS (kg)
38 127 19.0 98 76 4 15.9 1.9
50 152 19.0 121 89 4 19.0 2.8
64 178 19.0 140 114 4 19.0 3.9
76 191 19.0 152 127 4 19.0 4.5
102 229 19.0 190 165 8 19.0 6.4
127 254 19.0 215 187 8 22.2 8.0
152 279 19.0 241 213 8 22.2 9.7
203 343 19.0 298 270 8 22.2 14.6
254 407 25.4 362 330 12 25.4 26.5
305 483 25.4 432 397 12 25.4 37.8
356 534 28.6 476 435 12 28.6 51.4
406 597 28.6 540 502 16 28.6 64.5
457 635 31.7 578 536 16 31.7 81.4
508 699 31.7 635 594 20 31.7 98.9
610 813 34.9 749 705 20 34.9 146.8
762 985 38.1 914 870 28 34.9 240.4
914 1169 38.1 1086 1035 32 41.3 342.5
NOTES
1. Flange material: mild steel 1. Matérial de la bride: acier doux
Lining: stainless steel 316L Recouvrement: acier inox. 316L
2. Drilling: ASME B16.5 CL. 150 2. Perçage: ASME B16.5 CL. 150
3. For maximum working pressure 3. Pour pression maximale
see technical section. voir section technique.
4. Finish: galvanized. 4. Fini: galvanisé.
28
IPS ANGLE COLLARS
UNIFIEDALLOYS ASTM A 774
ANGLE / CORNIÈRE
DIA. (NOM.) A B WEIGHT / POIDS
DIMENSION
INCHES INCHES INCHES INCHES
mm mm mm mm LB kg
POUCES POUCES POUCES POUCES
3 75 3.5 89 3.56 90 3/4 x 3/4 x 1/8 16 x 19 x 3.2 0.5 0.2
4 100 4.5 114 4.56 116 1 x 1 x 1/8 25 x 25 x 3.2 0.8 0.4
5 125 5.56 141 5.62 143 1 x 1 x 1/8 25 x 25 x 3.2 1.0 0.5
1 x 1 x 1/8 25 x 25 x 3.2 1.5 0.7
6 150 6.62 168 6.75 171
1 x 1 x 3/16 25 x 25 x 4.8 2.2 1.0
*1¼ x 1¼ x 1/8 32 x 32 x 3.2 3.4 1.1
8 200 8.62 219 8.75 222
*1¼ x 1¼ x 3/16 32 x 32 x 4.8 3.6 1.6
*1¼ x 1¼ x 1/8 32 x 32 x 3.2 3.0 1.4
10 250 10.75 273 10.84 275
*1¼ x 1¼ x 3/16 32 x 32 x 4.8 4.5 2.0
1½ x 1½ x 1/8 38 x 38 x 3.2 4.3 1.9
12 300 12.75 324 12.84 326
1½ x 1½ x 3/16 38 x 38 x 4.8 6.5 2.9
1½ x 1½ x 1/8 38 x 38 x 3.2 5.0 2.3
14 350 14 356 14.09 358
1½ x 1½ x 3/16 38 x 38 x 4.8 7.0 3.2
1½ x 1½ x 3/16 38 x 38 x 4.8 8.0 3.6
16 400 16 406 16.09 409
1½ x 1½ x 1/4 38 x 38 x 6.3 10.5 4.7
1½ x 1½ x 3/16 38 x 38 x 4.8 9.0 4.1
18 450 18 457 18.09 460
1½ x 1½ x 1/4 38 x 38 x 6.3 12.0 5.4
1½ x 1½ x 3/16 38 x 38 x 4.8 10.2 4.6
20 500 20 508 20.12 511
1½ x 1½ x 1/4 38 x 38 x 6.3 13.5 6.1
2 x 2 x 3/16 51 x 51 x 4.8 15.7 7.5
24 600 24 610 24.12 613
2 x 2 x 1/4 51 x 51 x 6.3 21.0 9.5
2 x 2 x 1/4 51 x 51 x 6.3 26.0 11.8
30 750 30 762 30.12 765
2 x 2 x 3/8 51 x 51 x 9.5 39.0 17.7
2 x 2 x 1/4 51 x 51 x 6.3 31.0 14.1
36 900 36 914 36.12 918
2 x 2 x 3/8 51 x 51 x 9.5 46.5 21.1
NOTES
1. Material: Stainless steel 304L - 316L. 1. Matériau: acier inoxydable 304L - 316L.
Other alloys available upon request. Autres alliages disponibles sur demande.
2. Available in other thicknesses & diameters. 2. Autres diamètres et épaisseurs disponibles sur
demande.
3. For maximum working pressure 3. Pour pression maximale
see technical section. voir section technique.
*4. Sizes 8" & 10" - use 1" x 1" for slip-on type. *4. Grandeurs 8" & 10" - utiliser 1" x 1" pour type
coulissant.
29
MAXIMUM WORKING
UNIFIEDALLOYS PRESSURE
COLLARS COLLETS
PRESSED COLLARS
1 1/2" (38 mm) - 12" (305 mm) 150 psig 1 MPa
COLLETS EMBOUTIS
ROLLED COLLARS 4" (100 mm) - 24" (600 mm) 150 psig 1 MPa
COLLETS EN CORNIERE 30" (750 mm) & 36" (900 mm) 125 psig 850 kPa
NOTES
1. T3 is intended for use in ASME B31.1 and B31.3 1. Les brides T3 sont conformes aux exigences des
applications. Thickness must be calculated for codes ASME B31.1 et B31.3. Toutefois,
each case taking into consideration the bolting l'épaisseur doit être calculée pour chaque
material and the properties of the gasket material utilisation en tenant compte des propriétés des
used. matériaux des boulons et du joint d'étanchéité
utilisés.
2. T1, T2 & T5 are intended for non-toxic, non-lethal, 2. Les brides T1, T2 & T5 ne devraient être utilisées
non-flammable liquids in non-cyclic vibration-free qu'en cas de liquides non-toxiques, non-mortels,
service, and where ASME B31 piping codes are non-inflammables en service non-cyclique, sans
not applicable. Pressure rating is based on the use vibration, et non-assujettis aux codes ASME B31.
of soft gaskets.
3. Special machined "Type B" collar is available for 3. Un collet à face usinée "Type B" est disponible sur
pressures above 150 PSIG. commande pour des pressions supérieures à 150
PSIG.
30
IPS BACKING FLANGES
UNIFIEDALLOYS SLIP-ON
IN / PO 3 4 5 6 8 10 12
DIA. (NOM.)
mm 75 100 125 150 200 250 300
OUTSIDE DIA. IN / PO 7½ 9 10 11 13½ 16 19
DIA. EXTÉRIEUR mm 190 229 254 279 343 407 483
INSIDE DIA. IN / PO 4 1/8 5 1/8 6 1/8 7¼ 9¼ 11 3/8 13 3/8
DIA. INTERIEUR mm 105 130 156 184 235 289 340
IN / PO 5/8 5/8 5/8 5/8 5/8 5/8 3/4
T1
mm 15.9 15.9 15.9 15.9 15.9 15.9 19
IN / PO 3/4 3/4 3/4 3/4 3/4 1 1
T2
mm 19 19 19 19 19 25.4 25.4
IN / PO 3/4 3/4 3/4 3/4 7/8 1 1¼
T3
mm 19 19 19 19 22.2 25.4 31.7
NUMBER OF BOLTS
4 8 8 8 8 12 12
NOMBRE DE BOULONS
NOTES
1. Material: T2, mild steel. 1. Matériau: T2, acier doux.
T1, T3, A516 Gr. 70. upon request T1, T3, A516 Gr.70. sur demande seulement
2. Drilling: ASME B16.5 CL. 150 2. Perçage: ASME B16.5 CL. 150.
31
MAX. WORKING PRESSURE
UNIFIEDALLOYS I.D. PIPE & FITTINGS
DIA. NOM. ÉPAISSEUR NOMINALE TUYAU & COUDES R.L. COUDES À TÉS LATÉRAUX
(VOIR NOTES) RÉDUITS EMBOUTIS ONGLETS (VOIR NOTES) (VOIR NOTES)
(UNE R.L.
RÉDUCTION)
NOTES
1. Pressure ratings are limited to non-toxic, non- 1. Ces donnés ne s'appliquent qu'aux liquides non-
lethal, non-flammable liquids in non-cyclic toxiques, non-mortels, non-inflammables en
vibration-free service, and where ASME B31 service non-cyclique, sans vibration, et non-
piping codes are not applicable. assujettis aux codes ASME B31.
2. 2. Les tés et latéraux peuvent être conçus pour des
Pressure rating of tees & laterals can be increased
pressions plus élevées en utilisant des plaques de
by the use of reinforcing pads. Please contact
renfort. Veuillez vous renseigner auprès de nos
technical services.
services.
3. 3. Tolérance sur l'épaisseur d'après ASTM A 778 et
Thickness tolerance to ASTM A 778 and A 774.
A 774.
32
MAX. WORKING PRESSURE
UNIFIEDALLOYS I.P.S. PIPE & FITTINGS
COUDES À
DIA. NOM. DIA. EXTÉRIEUR ÉPAISSEUR NOMINALE TUYAU & RÉDUITS COUDES R.L. TÉS LATÉRAUX
ONGLETS
(VOIR NOTES) (UNE RÉDUCTION) EMBOUTIS (VOIR NOTES) (VOIR NOTES)
R.L.
NOTES
1. Pressure ratings are limited to non-toxic, non-lethal, non-flammable 1. Ces donnés ne s'appliquent qu'aux liquides non-toxiques, non-
liquids in non-cyclic vibration-free service, and where ASME B31 mortels, non-inflammables en service non-cyclique, sans vibration, et
piping codes are not applicable. non-assujettis aux codes ASME B31.
2. Thickness tolerance to ASTM A 778 and A 774. 2. Tolérance sur l'épaisseur d'après ASTM A 778 et A 774.
33
ASTM A 774
UNIFIEDALLOYS IPS ELBOWS
SCH 5S and 10S
90° 45°
DIA. (NOM.) O.D. / D.E. WALL / MUR A B WEIGHT / WEIGHT /
POIDS POIDS
INCHES INCHES INCHES INCHES INCHES
mm mm SCH. mm mm mm lb kg lb kg
POUCES POUCES POUCES POUCES POUCES
5S 0.083 2.1 1.8 0.8 0.9 0.4
3 75 3.5 89 4.5 114 2 51
10S 0.120 3.0 2.7 1.2 1.4 0.6
5S 0.083 2.1 3.2 1.4 1.6 0.7
4 100 4.5 114 6 152 2.5 63
10S 0.120 3.0 4.6 2.1 2.3 1.0
5S 0.109 2.8 9.0 4.1 4.5 2.0
6 150 6.62 168 9 229 3.75 95
10S 0.134 3.4 11.2 5.1 5.6 2.5
5S 0.109 2.8 16.0 7.3 8.0 3.7
8 200 8.62 219 12 305 5 127
10S 0.148 3.7 21.5 9.7 10.7 4.9
5S 0.134 3.4 31.5 13.8 15.2 6.9
10 250 10.75 273 15 381 6.25 159
10S 0.165 4.2 37.0 17.0 18.8 8.5
5S 0.155 4.0 50.0 22.9 25.0 11.5
12 300 12.75 324 18 457 7.5 190
10S 0.180 4.6 58.0 26.4 29.0 13.2
5S 0.154 4.0 64.0 29.0 32.0 14.5
14 350 14.0 356 21 533 8.75 222
10S 0.188 4.8 80.0 36.3 40.0 18.2
5S 0.165 4.2 89.0 40.4 44.0 20.2
16 400 16.0 406 24 610 10 254
10S 0.188 4.8 114.0 47.2 57.0 23.6
5S 0.165 4.2 114.0 51.7 57.0 25.8
18 450 18.0 457 27 686 11.25 286
10S 0.188 4.8 130.0 59.4 66.0 29.7
5S 0.188 4.8 160.0 72.6 80.0 36.3
20 500 20.0 508 30 762 12.5 317
10S 0.216 5.5 190.0 83.9 92.0 41.9
5S 0.218 5.5 267.0 121.0 133.0 60.5
24 600 24.0 610 36 914 15 381
10S 0.250 6.3 306.0 139.0 153.0 69.5
NOTES
1. Wall thicknesses are nominal. 1. L'épaisseur des murs est nominale.
2. Material: Stainless steel 304L - 316L. 2. Matériau: acier inoxydable 304L - 316L.
Other alloys available upon request. Autres alliages disponibles sur demande.
3. For maximum working pressure 3. Pour pression maximale
see technical section. voir section technique.
34
UNIFIEDALLOYS
Stainless Steel Piping
NOTES
1. Type of stiffeners: A) angle, B) flat bar. 1. Mode de renfort: A) cornière, B) méplat.
2. Minimum total weld length on each side of the 2. La longueur totale de la soudure de chaque côté
stiffener shall not be less than half of the du renforcement ne devrait pas être moins d'une
circumference. demi-circonférence.
UNIFIEDALLOYS
35
I.D. PRESSED COLLARS
UNIFIEDALLOYS ASTM A 774
4 102 6½ 165 0.125 3.18 4 5/16 110 4 7/32 107 0.9 0.41
NOTES
1. Material: Stainless steel 304L - 316L - 317L. 1. Matériau: acier inoxydable 304L - 316L -
Other alloys available upon request. 317L.
Autres alliages disponibles sur demande.
2. For maximum working pressure 2. Pour pression maximale
see technical section. voire section technique.
I.D. IN / PO 3 4 6 8 10 12
D.I. mm 76 102 152 203 254 305
Dia. IN / PO 5 6½ 8½ 10 5/8 12 ¾ 15
A mm 127 157 216 270 324 381
Dia. IN / PO 2½ 3 3½ 4 5 6
C mm 64 76 89 102 127 152
B .125" (3.18 mm) ALL SIZES / TOUTES LES GRANDEURS
36
I.D. ANGLE COLLARS
UNIFIEDALLOYS ASTM A 774
NOTES
1. Material: Stainless steel 304L - 316L. 1. Matériau: acier inoxydable 304L - 316L.
Other alloys available upon request. Autres alliages disponibles sur demande.
2. For maximum working pressure 2. Pour pression maximale
see technical section. voire section technique.
*3. For slip-on collar 24" - use 1 ½ (38 mm) *3. Pour collet coulissant de 24" - utilisez
angle.
cornière 1 ½ (38 mm)
37
UNIFIEDALLOYS MAXIMUM UNSUPPORTED SPAN FOR
STAINLESS STEEL PIPE FILLED WITH WATER
TEMP: 200°F (100°C) max
ASTM A 778 / ASTM A 774
36 15 4.6 25 7.6
NOTES
This table is applicable to pipes operating at a Ce tableau est valide pour tuyaux opérant à des
maximum temperature of 200°F (100°C), and températures ne dépassant pas 200°F (100°C), et
supported on saddles covering at least one-third of supportés sur au moins 1/3 de la circonférence.
the circumference.
38
TOLERANCES OF
UNIFIEDALLOYS PIPE AND FITTINGS
90° ELLs
NOMINAL ALL PIPE 45° ELLs REDUCERS BACKING SQUARENESS
DIAMETER AND FITTINGS LATERALS COLLARS FLANGES ALL PIPE AND FITTINGS OVALITY
TEES, Y's AT WELDING
O.D. AT CENTER ENDS
OVERALL BOLT
INCHES mm WELDING TO END OD / ID A B
LENGTH CIRCLE
END DIM
1 1/2 38
2 50 ± 1/32" ± 1/32" ± 1/16" ± 1/16"
2 1/2 65
(± 1 mm) (± 1 mm) (± 2 mm) (± 2 mm)
3 75
± 1/16" ± 1/16"
4 100
6 150 (± 2 mm) (± 2 mm)
+ 1/16" ± 1/8" ± 3/32"
± 1/16"
- 1/32"
8 200 (+ 2 mm)
(± 2 mm) (± 3.2 mm) (± 2.5 mm)
(- 1 mm)
± 1/8" ± 1/16"
10 250 ± 3/32" ± 3/32" ± 3/32" ± 3/16" ± 1/8"
+ 3/32"
12 300 (± 2.5 mm) (± 2.5 mm) (± 3.2 mm) (± 2 mm) (± 2.5 mm) (± 5 mm) (± 3.2 mm)
- 1/32"
14 350 ± 3/32" ± 1/4"
(+ 2.5 mm) (± 2.5 mm) (± 7 mm) ± 5/32"
16 400
(- 1 mm) (± 4 mm)
18 450 ± 1/8" ± 3/8"
20 500 ± 1/8" ± 1/8" ± 3/16"
24 600 + 1/8" (± 3.2 mm) (± 10 mm) (± 5 mm)
- 1/32" (± 3.2 mm) (± 3.2 mm)
± 3/8"
30 750 ± 1/4"
(± 10 mm)
(+ 3 mm) ± 3/16"
36 900 (- 1 mm) (± 5 mm) ± 1/2"
(± 7 mm)
40 1016 (± 13 mm)
A A A A
39
UNIFIEDALLOYS
FABRICATING TOLERANCES
METRIC CONVERSIONS
Pipe sizes together with applicable wall thicknesses are not shown with
metric equivalents. The SI (metric) values where included with the
customary U.S. values in this Standard are the rounded equivalents of the
U.S. values and are for reference only.
Conversion Factor
inches to
25.4
millimetre
40
APPLICATION OF PIPE
UNIFIEDALLOYS FABRICATION TOLERANCES
“A”
ROTATION OF FLANGES
FROM THE INDICATED
POSITION MEASURED AS
SHWON 1/16” MAXIMUM
1/ ”
x x 8
“A”
“A”
“A”
“A”
SECTION X-X
ALIGNMENT OF FACINGS OR
“A ENDS SHALL NOT DEVIATE
“A”
UNIFIEDALLOYS
41
FRACTIONS AND DECIMAL
UNIFIEDALLOYS EQUIVALENTS
UNIFIEDALLOYS
42