Documente Academic
Documente Profesional
Documente Cultură
Exam questions
1 . You want to statically define an ARP entry. Which command do you use?
2 . What categories of information should you take into consideration when you document the properties of a router for a Network
Configuration Table? (Choose three)
STP state
interface IP address
EtherChannel configuration
management IP address
interface types
3 . What command would you use to display the LMI DLCI number on a Frame Relay interface?
4 . What command would you use to display the contents of all current IP access lists?
show ip access-lists
show ip acl
TrafficDirector
NetSys
CiscoWorks
CiscoView
6 . The following is output from the “debug ppp negotiation” command. What does this output tell you?
This is a normal negotiation, where both sides agree on Network Control Program (NCP) parameters
Digital Multimeter
Breakout Box
Protocol Analyzer
Cable Tester
8 . What are three ways that the ARP entries from the ARP Cache table are removed?
9 . What four groups in the RMON specification (RFC 1757) does the Catalyst 5000 embedded RMON agent support?
Statistics Group
Supervisor Group
History Group
Alarms Group
Events Group
console
buffer
syslog server
Your LMI does not have to match the service providers LMI
If your router supports auto-sensing, you can’t manually configure the LMI
12 . Which command would you use to clear all statistics from access list statements?
13 . You receive the following output: Router#traceroute 10.3.3.3 Type escape sequence to abort. Tracing the route to 10.3.3.3 1
10.1.1.1 4 msec 4 msec 4msec 2 U U U 3 U U U ^C Router# What does this output mean?
A timed-out request
14 . Which of the following documentation traits have to be addressed when creating network diagram standards?
Inventory
Abbreviations
Configurations
Command syntax
Digital Multimeter
Volt-Ohm Meter
TDR
Network Monitor
SNMP
RPC
DNS
TFPT
IPX
Spanning Tree
SPAN
RMON8
CWSI
18 . You want your router to rediscover a reconfigured device and allow the router to be aware of newer devices. Which command
would you use?
19 . When troubleshooting a network, what are the advantages of using a logically layered network model?
Robustness
Security
Speed
Error checking
21 . Which one of the following is the leading cause of lost network availability?
Natural disasters
Operational errors
22 . What tool should you use to check for attenuation and return loss in the three predominant wavelengths -- 850nm, 1300nm, and
1500nm?
TDR
Volt-Ohm Meter
Digital Multimeter
23 . Which processes does TCP, but not UDP, use? Choose two.
Windowing
Acknowledgements
Source Port
Destination Port
24 . You want to display the current TCP/IP network configuration parameters on a Windows 98 client. What command would you
use?
ipconfig
winipcfg
winipconfig
winipcfg /showclassid
25 . What does the following output from the “debug isdn q931” command tell you?
A call teardown procedure from the router
26 . According to Cisco’s problem-solving model, what should a network troubleshooter do after they have resolved a problem?
27 . What command would you use to show the BRI 0 PPP status?
debug bri
show interface
29 . You want to know which devices your router can access out of the FastEthernet0 port at this particular moment. Which command
should you use?
show ip packets
show arp
show cache
30 . Which of the following components should you include in an End-System Topology Diagram? (Choose all that apply.)
Device illustration
Operating system
IP routing protocol
Device name
VTP domain
31 . While using the “debug isdn q921” command, what is the first AI value after doing a “no shut” on the BRI 0 interface to start a TEI
(Terminal Endpoint Identifier)?
64
127
128
33 . Which of the following commands converts broadcast messages into directed broadcast or unicast messages?
ip dhcp pool
ip helper-address
ip bootp agent
netbios-name-server
34 . Which of the following pieces of information are relevant to an end-system network configuration table? Select four.
35 . When analyzing a network problem; in what terms should a network troubleshooter define the problem?
36 . If the IP helper address is specified and UDP forwarding is enabled, broadcast packets destined for the following protocols are
forwarded by default:
Only A, B, C, and D
Only B, D, E, F, and G
37 . A problem while troubleshooting fiber optic networks is called fiber optic asymmetric connectivity? Which of the following best
describes this?
The transmit cable fails while the receive cable continues working
The receive cable fails while the transmit cable continues working
One side of a transmit and receive cable fails, but the remaining cable nonetheless forwards frames
38 . What does the following output from the “debug isdn q931” command tell you?
39 . You want to set up a default gateway on your router so that any IP address with any subnet mask will be sent out of the interface
172.16.100.1. What command would you use to accomplish this?
40 . Which of the following is a network process characterized by the following: Log in, Interface discovery, and Device discovery?
Network testing
Network documentation
Network configuration
Network troubleshooting
41 . Only the local DLCI 0 and DLCI 1023 come up. What should you do?
Check again in 5 minutes because DLCIs take approximately 5 minutes to become active after being configured
Use the “show frame-relay map” command to check the status of the DLCIs
42 . Which of the following best describes the process of the connection-oriented three-way handshake?
Two packets consisting of SYN, SYN/ACK (the second and third parts of the three-way handshake are including in the second
packet)
This is a normal negotiation, where both sides agree on Network Control Program (NCP) parameters
44 . While looking at a datagram, you notice that the Protocol field contains 17. What protocol is being used to send the datagram?
TCP
IP
UDP
ICMP
SNMP
CHAP
PAP
RMON
NetSys
CiscoWorks 2000
CiscoView
47 . Encryption and tunneling protocols that work with PAT (Port/Address Translation) sometimes have problems. At which OSI level
do PAT problems exist at?
Network Layer
Transport Layer
Presentation Layer
Physical Layer