Documente Academic
Documente Profesional
Documente Cultură
COMPRESSORS
GENUINE PARTS
SERVICE
Sundyne Corporation
14845 West 64th Avenue
Arvada, Colorado 80007
USA
Phone: 1.303.425.0800
Fax: 1.303.425.0896
www.sundyne.com SIMPLE BY DESIGN ™
Power monitoring represents one of the best values available today to protect your pump from system upset
damage and avoid costly shutdowns, unexpected repair costs, and premature equipment failures. SundGard
Power Monitors are easy to install and operate, and designed to protect your pump from:
• Dry-Running Conditions
• Low Flow / “Back-on-Curve” Operation
• Increased Viscosity / Precipitation
• Deadhead / Closed Discharge Valve
• High Flow / “End-of-Curve Operation
Sundyne Sealless Pumps
• Jammed Impeller
What makes Sundyne sealless pumps a better, more • Severe Cavitation
reliable, choice for your process? It’s simple: • Decoupled Magnetic Drive
Unlike competitive pump designs, the Ansimag Ansimag Pumps have the fewest wear parts of any
stationary shaft design tolerates greater changes in operating magnetic drive pump on the market today.
system conditions.
Solving Your Most Demanding Corrosive and Hazardous Pumping Challenges
● Chemical Processing
• Transfer
KM K+ KF • Unloading
• Bulk Storage
● Hydrocarbon Processing/Refining
• Sour Water
“Sub-ANSI” pumps for lower flow ANSI dimensioned pumps for Large ANSI dimensioned pumps for
• Neutralization Industry Leadership
requirements chemical process applications higher flow and head requirements
• Boiler House Engineering expertise delivering
complete UPTIME ASSURANCE™
● General Industrial
Performance Envelopes • Steel Finishing, Pickling, Etching
• Electroplating Typical Services
• High Purity Processes
• Filtration ● Acid ● Benzene
Specifications ● Caustic Soda
• Acetic
● Municipal • Chlorosulphonic ● Bleach Solution
• Flow: to 1400 GPM (318 m3/h) • Wastewater/Wastechemical Treatment • Chromic ● Ferric Chloride
• Scrubber Systems • Hydrochloric ● Ferrous Chloride
• Hydrofluoric ● Hydrogen Peroxide
• Head: to 500 feet (152 m)
● Mining • Nitric ● Methanol
• Leaching Experience and Reliability • Oleum ● Methyl Ethyl Ketone
• Temp: -120°F to 250°F (-84°C to 121°C) Experience you can count • Phosphoric ● Sodium Hydroxide
● BioFuels on to handle the toughest • Sulfuric ● Sodium Hypochlorite
• Distillation applications ● Sodium Sulfate
• Pressure: to 350 psi (24 Bar) ● Acetone
• Transesterification ● Aluminum Chloride ● Sour Water
• Neutralization ● Ammonia
• Design Standard: ANSI B73.3 (K+ and KF)
● Pulp & Paper
• Bleaching
• Waste Treatment
● Pharmacuetical
SIMPLE BY DESIGN (Model K+ Shown)
Options
Outer Magnet Drive
- Neodynium Iron Boron magnets for hard-start, • PFA Construction (in select sizes) for maximum
synchronous operation. corrosion resistance
- Magnets are fully encapsulated for protection • Frame Mounted Pumps for direct sealed pump
against corrosion and physical damage. replacement
• ANSI/ASME B16.5 Class 300 flanges for
higher operating pressure capability
Shaft Support O-Ring Rear Casing Rear Casing Support
Shaft • ISO 2858 and JIS B8313 dimensional pumps
Casing Drain - Fully supported, oversized shaft for worldwide installation capability
eliminates deflection for maximum • 316 Stainless Steel Casings (in select sizes)
durability. for cryogenic applications to -120°F
- Patented groove enables unexpected
particles to pass through the pump without
Casing disturbing flow or damaging the bushings.
- Solid, non-rotating design eliminates
need for internal fasteners or o-rings.