Sunteți pe pagina 1din 11

1 INTRODUCTION

This document describes the procedure to upgrade LTMR.

Limitation: this package and procedure describe only the upgrade of the LTMR firmware for all network
versions (Modbus, Profibus, DeviceNet, CANopen and Ethernet)

1.1 Setup
Content of the TeSysT upgrade package:
 LTMR Upgrade procedure
 TeSysT Programmer
 Different Firmware Packages

Installation procedure:

1. Extract the files of the zip in the


folder of your choice: the calibration
Files folder is reserved for the
programmer use.
The Firmware Packages folder is created
to receive the different Firmware versions
included in the TeSysT upgrade package

2. Install the firmware package:


Extract the files of each firmware
packages zip in the Firmware Packages
folder.
You can install only the firmware package
you want to download into the product
You can now use the Programmer
Software to upgrade products

1
3A. Hardware installation: serial line on
SubD
Plug RS232 -->RS485 converter to the
PC serial port (1)
Plug RJ45 cable on the converter and
on the HMI port of the LTMR (2)
1
 Energize the LTMR: power LED should 2
be green

3B. Hardware installation: on USB port


Plug the USB connector of the
TCSMCNAM3MxxxP cable in the PC USB
port
Plug RJ45 cable on the converter and the
HMI port of the LTMR
To know which port number is affected to
the virtual Com port if using the the
TCSMCNAM3MxxxP cable, open the
device manager and expand the
Ports(COM & LPT) line
c Energize the LTMR: power LED should
be green

4. Only for Ethernet product:


 Plug Ethernet cable from one side to
TeSys T network port and the other side
to the Ethernet RJ45 of the PC
Open Network configurations and click
on Properties

2
Select Internet Protocol (TCP/IP) and
click on Properties

Select Use IP address radio button


Fill the PC IP address with 85.16.0.1 and
the subnet mask with 255.0.0.0
On the TeSys T product, make sure that
IP address is set to 0.0.0.0.
This is true in the following cases:
- for an "out-of-the-box" TeSys T product
- after a "Clear All command"
- by rotating the Ones thumbwheel to
ClearIP position, executes a power
Cycle.
In this state, when the Ones thumbwheel
is on Disabled position, TeSys T will
responds to an IP address which starts
by 85.16 and finishes with the 2 last
bytes (converted in decimal) of the
product MAC address as end of IP
address
For example
Product MAC address: 0080 F4D0 0114
 default IP address: 85.16.1.20 (0x01
= 1; 0x14 = 20)

3
To check this connection
Connect the PC and the TesSys T
product
Open a command line window on the PC

Execute a ping to the TeSys T default IP


address

4
2 UPGRADE PROCEDURE FOR MODBUS/CANOPEN/DEVICENET/PROFIBUS

1. Run the TeSysT programmer and set the serial port number if different from the
default value

2. Click “Load Firmware Package” and select the desired firmware package from
“Firmware Packages” folder.

5
3. Select the .fw file and valid your choice

4. All firmware releases ready to be downloaded are displayed

5. Click “Connect to LTMR on HMI port”. Software will change to “Connected” and
display versions inside of the unit

6
6. Click “Program LTMR. Read the warning message and press “Proceed” to start the
download process

7. LEDs will blink and you can see the evolution of the progress bar on the PC tool.
Download will take about 5 minutes.

8. When finished , the following message will appear.

Power cycle the LTMR and press OK


9. TeSys T Programmer will indicate “Programming finished successfully” and re-read
the firmware versions loaded in LTMR
10. The LTMR is now ready to use

7
3 UPGRADE PROCEDURE FOR ETHERNET

1. Run the TeSysT programmer and set the serial port number if different from the
default value

2. Click “Load Firmware Package” and select the desired firmware package from
“Firmware Packages” folder.

8
3. Select the .fw file and valid your choice

4. All firmware releases ready to be downloaded are displayed

5. Click “Connect to LTMR on HMI port”. Software will change to “Connected” and
display versions inside of the unit.

9
6. A valid IP address which corresponds to the TeSys T Ethernet port must be entered

7. Click on ‘Connect to LTMR on Ethernet port’. All firmware versions in the product are
identified. Connection state is updated and a message will confirm the connection to
Ethernet port

8.
9. Click “Program LTMR. Read the warning message and press “Proceed” to start the
download process

10
10. LEDs will blink and you can see the evolution of the progress bar on the PC tool.
Download will take about 8 minutes.

11. When finished , the following message will appear.

Power cycle the LTMR and press OK


12. TeSys T Programmer will indicate “Programming finished successfully” and re-read the
firmware versions loaded in LTMR
13. The LTMR is now ready to use

11

S-ar putea să vă placă și