Documente Academic
Documente Profesional
Documente Cultură
To Check the Number of HSDPA User allocated per cell: LST UCELLCAC-----in RNC
end
3. LST OP ADD OP (For Creating Account in RNC/BSc for Local login during M2000
Connectivity down)
6. DSP UCELL---To check the status of Node-B cell(Result---Cell is Setup and enabled)DSP
UCELLCHK---to check traffic in RNC end BLK UCELL---to Block cell in RNCDEA
UCELL--To Deactivate Cell in RNC.ACT UCELL--To Activate Cell in RNCUBL UCELL--
--To UBlock Ucell in RNCBLK Unode-B----To Block Unode-B in RNCUBL Unode-B----To
Unblock Unode-B in RNCRST Unode-B----to Reset Unode-B in RNCPING IP--------To ping
the Node-B Service from RNC TRC IPADDR------To check where we are getting drop in
RNCLST UCELL------To get information about the Cell like
PSC,Frequency,Transmitting Power,LAC,SAC,RAC in RNCLST UPCPICH------To check
pilot channel powerMOD UPCPICHPWR----To Change Pilot Channel Power in RNC.LST
UINTRAFREQNCELL------Use this command to query the intra-frequency neighboring
cell.ADD UINTRAFREQNCELL---- to add neighbour Cells (IntraFreq)
HUAWEI NODEB O&M BASIC MML COMMANDS
To connect to Node B, Go to Local Maintenance Terminal : Install LMTCreate Office/add
:Name : NODEBIP : 17.21.2.15UN : adminPW : NodeBLMT :Segment IP Add of Laptop :IP
: 17.21.2.10SM : 255.255.255.0
REQ CMCTRL:;
when connecting via LMT at Site this command will be use to manage/control configured
thenodeb using LMT. It will display CM CONTROL States LMT Enabled instead of M2000.After
disconnecting the Node B via LMT, it will forced/automatically transfer to M2000 command control.
FOC CMDCTRL:;
To force the control of the Node B to LMT.
LST NODEBTYPE
display the nodeb model.
DSP BRD
Display the status of BBU.
DSP BRD:;
77P5416GSNO+++ 77P5416GSNO 2011-06-21 15:02:11O&M #38644%%/*21227*/DSP
BRD:;%%RETCODE = 0 Succeed.Board Status------------
Cabinet No. Subrack No. Slot No. Board Type Standby Status Availability Status Operate
State Admin State
Master 0 3 WBBP NULL Normal Enabled UnblockedMaster 0 7 WMPT Active Normal
Enabled NULLMaster 0 16 UBF NULL Normal Enabled NULLMaster 0 19 UPEA NULL
Normal Enabled NULLMaster 4 0 WRFU NULL Normal Enabled Unblocked(Number of
results = 5)DSP CELLDSP CLKSRCLST ETHPORTDSP E1T1DSP CLKSTATLST
ALMLOG
DSP IUBCP
:;
RETCODE = 0 Succeed.NCP/CCP Port Status-------------------NCP/CCP Port Type =
CCPCCP Port No. = 0Belong Flag = Master RncMaster/Slave Flag = MasterCCP Port Status
= NormalCCP Use State = UsedNCP/CCP Port Type = NCPBelong Flag = Master
RncMaster/Slave Flag = MasterNCP Port Status = NormalNCP Use State = Used(Number of
results = 2)
LST IUBCP:; -
to Identify the kind of txmn we of the bts.