Documente Academic
Documente Profesional
Documente Cultură
Information
Box Includes
QuickStart Guide
FortiGate/FortiWiFi
Ethernet Cable
4 Rubber Feet
2 WiFi Antennas
(WiFi models only) Wall Mount Kit
Installation
The FortiGate unit can be placed on any flat surface with the provided rubber feet, or
mounted to a wall with the providing mounting hardware.
1. Ensure that the surface onto which the FortiGate unit to be installed is clean, level,
and stable and that there is at least 1.5in (3.8cm) of clearance on all sides to allow
for adequate airflow.
2. Attach the provided rubber feet to the bottom of the FortiGate unit.
3. Place the unit in the designated location.
4. Verify that the spacing around the FortiGate unit conforms to requirements and that
the unit is level.
5. If applicable, attach the antennas to the device.
6. Plug the provided power adapter into the rear of the unit, and then plug the
transformer into a grounded electrical outlet or a separate power source such as
an uninterruptible power supply (UPS) or a power distribution unit (PDU) with the
provided power cable.
1. Use the mounting bracket to mark the location of the mounting holes on a flat wall
surface.
2. Drill the mounting holes in the marked locations.
3. Insert the provided anchors into the drilled holes then screw the
screws into the anchors, leaving approximately 2mm of the screw
exposed for connecting to the mounting bracket.
Power
Green: The unit is on
Off: The unit is off
Status
Green: Normal
Flashing Green: Booting up
HA
Green: Operating in an HA cluster
Off: Not in an HA cluster
FortiGate 60E/61E
Power
12V DC
100-240V AC, 50-60Hz adapter
Console (RJ-45)
Optional connection to the management computer
Provides access to the CLI
USB (USB A)
USB 3.0 server port
FortiGate 60E-POE
Max PoE
Red: Maximum PoE power allocated
Off: PoE power available
PoE
Logo Green : PoE device powered
Green: The unit is on Flashing Green: PoE device requesting power
Off: The unit is off Off: No PoE device connected
Power
Green: The unit is on
Off: The unit is off
Status
Green: Normal
Flashing Green: Booting up
HA
Green: Operating in an HA cluster
Off: Not in an HA cluster
Power
54V DC
100-240V AC, 50-60Hz adapter
Console (RJ-45)
Optional connection to the management computer
Provides access to the CLI
Power
Green: The unit is on
Off: The unit is off
Status
Green: Normal
Flashing Green: Booting up
HA
Green: Operating in an HA cluster
Off: Not in an HA cluster
WiFi
Green: WiFi connected
Flashing Green: WiFi active
Off: WiFi disabled
FortiWiFi 60E/61E
Power
12V DC
100-240V AC, 50-60Hz adapter Antenna Connection (SMA)
Console (RJ-45)
Optional connection to the management computer
Provides access to the CLI
USB (USB A)
USB 3.0 server port
Safety For product available in the USA/Canada market, only channel 1~11 can be
operated. Selection of other channels is not possible.
Battery – Risk of explosion if the battery is replaced by an incorrect type. Do
not dispose of batteries in a fire. They may explode. Dispose of used batteries Pour les produits disponibles aux États-Unis / Canada du marché, seul le canal 1
according to your local regulations. IMPORTANT: Switzerland: Annex 4.10 of à 11 peuvent être exploités. Sélection d’autres canaux n’est pas possible.
SR814.013 applies to batteries.
This equipment complies with ISED radiation exposure limits set forth for an
Batterie – Risque d’explosion si la batterie est remplacée par un type incorrect. uncontrolled environment. This equipment should be installed and operated with
Ne jetez pas les batteries au feu. Ils peuvent exploser. Jetez les piles usagées minimum distance 22cm between the radiator & your body.
conformément aux réglementations locales. IMPORTANT: Suisse: l’annexe 4.10
de SR814.013 s’appliquent aux batteries. Cet équipement est conforme aux limites d’exposition aux rayonnements ISED
établies pour un environnement non contrôlé. Cet équipement doit être installé
警告 et utilisé avec un minimum de 22cm de distance entre la source de rayonnement
本電池如果更換不正確會有爆炸的危險 et votre corps.
請依製造商說明書處理用過之電池
The maximum antenna gain permitted for devices in the band 5725-5850 MHz
Caution: This equipment is to be used in a Network Environment 0 per IECTR shall be such that the equipment still complies with the e.i.r.p. limits specified for
62101. This product is connected only to PoE networks without routing to the point-to-point and non-point-to-point operation as appropriate.
outside plant.
Le gain maximal d’antenne permis (pour les dispositifs utilisant la bande 5725-
Attention: Ce matériel doit être utilisé dans un Environnement Réseau 0 par 5850 MHz)
IECTR 62101. Ce produit est uniquement connecté aux réseaux PoE sans doit se conformer à la limite de p.i.r.e. spécifiée pour l’exploitation point à point et
installation externe de routage. non point à point, selon le cas.
Regulatory Notices Caution: The device for the band 5150-5250 MHz is only for indoor usage to
reduce potential for harmful interference to co-channel mobile satellite systems.
High-power radars are allocated as primary users (i.e. priority users) of the bands
Federal Communication Commission (FCC) – USA 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interfer-
ence and/or damage to LE-LAN devices.
This device complies with Part 15 of FCC Rules. Operation is subject to the
following two conditions: Attention: Le dispositif de la bande 5150-5250 MHz est réservé à un usage
(1) this device may not cause harmful interference, and intérieur afin de réduire l’interférence nuisible potentielle aux systèmes mobiles par
(2) this device must accept any interference received; including interference that satellite co-canal. Les radars à haute puissance sont désignés comme utilisateurs
may cause undesired operation. principaux (à savoir les utilisateurs prioritaires) des bandes 5250-5350 MHz et
5650-5850 MHz et que ces radars pourraient causer des interférences et / ou
This equipment has been tested and found to comply with the limits for a Class endommager les périphériques LE-LAN
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in residential instal- This device has been designed to operate with an antenna having a maximum
lation. This equipment generates, uses, and can radiate radio frequency energy, gain of 3 dBi for 2.4GHz and 6 dBi for 5GHz. Antenna having a higher gain is
and if it is not installed and used in accordance with the instruction manual, it strictly prohibited per regulations of ISED. The required antenna impedance is
may cause harmful interference to radio communications. However, there is no 50 ohms.
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, Under ISED regulations, this radio transmitter may only operate using an antenna
which can be determined by turning the equipment off and on, the user is of a type and maximum (or lesser) gain approved for the transmitter by ISED. To
encouraged to try to correct the interference by one or more of the following reduce potential radio interference to other users, the antenna type and its gain
measures: should be so chosen that the equivalent isotopically radiated power (e.i.r.p.) is not
Reorient or relocate the receiving antenna. more than that necessary for successful communication.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to Ce dispositif a été conçu pour fonctionner avec une antenne ayant un gain
which the receiver is connected. maximal de 3 dBi pour 2,4 GHz et 6 dBi pour 5GHz. Une antenne ayant un gain
Consult the dealer or an experienced radio/TV technician for help. supérieur sont strictement interdites par la réglementation d’ISED. L’impédance
d’antenne requise est de 50 ohms.
WARNING: Any changes or modifications to this unit not expressly approved by
the party responsible for compliance could void the user’s authority to operate Conformément à la réglementation d’ISED, cet émetteur radio peut fonctionner
the equipment seulement avec une antenne d’un type et d’un gain maximal (ou inférieur) ap-
prouvé pour l’émetteur par ISED. Dans le but de réduire les risques de brouillage
This equipment complies with FCC radiation exposure limits set forth for an radioélectrique aux autres utilisateurs, il faut choisir le type d’antenne et son gain
uncontrolled environment. This equipment should be installed and operated with de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas
minimum distance 20cm between the radiator and your body. This transmitter l’intensité nécessaire à l’établissement d’une communication réussie.
must not be co-located or operating in conjunction with any other antenna or
transmitter. This radio transmitter 7280B-120512 has been approved by ISED to operate with
the antenna types listed below with the maximum permissible gain and required
Caution: Operation of this device is restricted to indoor use only. antenna impedance for each antenna type indicated. Antenna types not included
in this list, having a gain greater than the maximum gain indicated for that type,
For operation within 5.15 ~ 5.25GHz frequency range, it is restricted to indoor are strictly prohibited for use with this device.
environment. The band from 5600-5650MHz will be disabled by the software
during the manufacturing and cannot be changed by the end user. Le présent émetteur radio 7280B-120512 a été approuvé par ISED pour
fonctionner avec les types d’antenne énumérés ci-dessous et ayant un gain
This device meets all the other requirements specified in Part 15E, Section admissible maximal et l’impédance requise pour chaque type d’antenne. Les
15.407 of the FCC Rules. types d’antenne non inclus dans cette liste, ou dont le gain est supérieur au gain
maximal indiqué, sont strictement interdits pour l’exploitation de l’émetteur.
Industry Canada Equipment Standard for Digital Equipment This device and it’s antennas(s) must not be co-located or operating in
(ICES) – Canada conjunction with any other antenna or transmitter except in accordance with IC
multi-transmitter product procedures.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil et son antenne (s) ne doit pas être co-localisés ou fonctionnement en
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du association avec une autre antenne ou transmetteur.
Canada.
Wireless models only:
Gain (dBi)
Antenna Type Connector Simplified EU Declaration of Conformity
2.4GHz 5GHz
This declaration is only valid for Fortinet products (including, combinations of
Dipole RSMA 3 6 software, firmware and hardware) provided by Fortinet or Fortinet’s authorized
partners to the end-customers directly for use within the EU or countries that
have implemented the EU Directives and/or spectrum regulation. Any Fortinet
Professional Installation Instruction products not obtained directly from Fortinet or Fortinet’s authorized partners
1. Installation personnel may not comply with EU Directives and Fortinet makes no assurances for such
This product is designed for specific application and needs to be installed by products.
qualified personnel who has RF and related rule knowledge. The general user
shall not attempt to install or change the settings. Български
2. Installation location Този продукт е в съответствие с Директива 2014/53/ЕС.
The product shall be installed at a location where the radiating antenna can
be kept 22cm from nearby person in normal operation condition to meet Česky
Regulatory RF exposure requirement. The installation applies to both indoor Tento produkt je v souladu se směrnicí 2014/53/EU.
and outdoor location.
3. External antenna(s) Dansk
Use only the antenna(s) that have been approved by the manufacturer. The Dette produkt er i overensstemmelse med direktiv 2014/53/EU.
non-approved antenna(s) may produce unwanted spurious or excessive RF
transmitting power that may lead to the violation of FCC/ISED limit and is Deutsch
prohibited. Dieses Produkt entspricht der Richtlinie 2014/53/EU.
4. Warning
Please carefully select the installation position and ensure that the final output Eesti
power does not exceed the limit set forth in relevant rules. The violation of the See toode vastab direktiivile 2014/53/EL.
rule could lead to serious federal penalty.
English
Instructions d’installation professionnelle This product is in compliance with Directive 2014/53/EU.
1. Installation
Ce produit est conçu pour un usage spécifique et doit être installé par un Español
personnel qualifié maîtrisant les radiofréquences et règle similaires. L’utilisa- Este producto cumple con la Directiva 2014/53/UE.
teur ne doit pas tenter d’installer ou de modifier les paramètres.
2. Emplacement d’installation Ελληνική
En usage normal, afin de respecter les exigences réglementaires concernant Το προϊόν αυτό συμμορφώνεται με την Οδηγία 2014/53/ΕΕ.
l’exposition aux radiofréquences, ce produit doit être installe de façon à
respecter une distance de 22cm entre l’antenne émettrice et. L’installation Français
s’applique aux emplacements intérieur et extérieur. Ce produit est conforme à la Directive 2014/53/UE.
3. Antenne externe (s)
Utiliser uniquement l’antenne (s) approuvées par le fabricant. L’utilisation Hrvatski
d’autres antennes peut conduire à un niveau de rayonnement essentiel ou Ovaj proizvod je u skladu s Direktivom 2014/53/EU.
non essentiel dépassant les niveaux limites définis par FCC/ISED, ce qui
est interdit. Italiano
4. Avertissement Questo prodotto è conforme alla Direttiva 2014/53/EU.
Choisir avec soin la position d’installation et s’assurer que la puissance de
sortie ne dépasse pas les limites en vigueur. La violation de cette règle peut Latviski
conduire à de sérieuses pénalités fédérales. Questo prodotto è conforme alla Direttiva 2014/53/EU.
Lietuvių
European Conformity (CE) - EU Šis gaminys atitinka direktyvą 2014/53/ES.
This is a Class B product. In a domestic environment, this product may cause Malti
radio interference, in which case the user may be required to take adequate Dan il-prodott huwa konformi mad-Direttiva 2014/53/UE.
measures.
Magyar
Ez a termék megfelel a 2014/53/EU irányelvnek.
Nederlands
Dit product is in overeenstemming met Richtlijn 2014/53/EU.
The product transmits within the frequency ranges and less than or equal to the
power listed below: Norsk
2412-2472MHz less than 20dBm Dette produktet er i samsvar med direktiv 2014/53/EU.
5180-5240MHz less than 23dBm
Polski
Voluntary Control Council for Interference (VCCI) – Japan Ten produkt jest zgodny z dyrektywą 2014/53/UE.
この装置は、クラスB情報技術装置です。この装置は、家庭環境で使用するこ Português
とを目的としていますが、この装置がラジオやテレビジョン受信機に近接して Este produto está em conformidade com a Diretiva 2014/53/UE.
使用されると、受信障害を引き起こすことがあります。
取扱説明書に従って正しい取り扱いをして下さい。 Rumunski
VCCI-B Acest produs este în conformitate cu Directiva 2014/53/UE.
Slovensky
Product Safety Electrical Appliance & Material (PSE) – Japan
Tento produkt je v súlade so smernicou 2014/53/EÚ.
日本では電気用品安全法(PSE)の規定により、同梱している電源コードは本製
Slovensko
品の専用電源コードとして利用し、他の製品に使用しないでください。
Ta izdelek je v skladu z Direktivo 2014/53/EU.