Documente Academic
Documente Profesional
Documente Cultură
1
⁄4 0.12 3.40 1,360
5
⁄16 0.18 5.27 2,108
3
⁄8 0.26 7.55 3,020
7
⁄16 0.35 10.2 4,080
1
⁄2 0.46 13.3 5,320
9
⁄16 0.59 16.8 6,720
5
⁄8 0.72 20.6 8,240
3
⁄4 1.04 29.4 11,760
7
⁄8 1.42 39.8 15,920
11
⁄8 2.34 65.0 26,000
** Minimum breaking forces listed above apply to ropes with bright or drawn galvanized wires. Minimum breaking forces are 10% lower 6 x19 IWRC
for ropes with wires galvanized at finish size.
*Regarding wire rope, ANSI B30.7, requires a minimum of 5:1 design factor with an 18:1 rope pitch diameter to drum is required for
lifting and lowering applications.
2. How fast is the load to be moved e. Clutches: In the U.S.A., clutches are
(if at all)? permitted on lifting winches. Although we
don’t usually recommend them, for certain
3. How much wire rope is needed? lifting applications they make sense. In
Contact your Lifting Gear Hire representative to Europe, clutches are not allowed on lifting
help you answer these questions and guide you winches. The Liftstar series is for lifting and
through the selection process. the Pullstar for pulling. They are the same
winches, but with different ratings — and
Lifting applications are generally defined as the Pullstar winches have clutches.
those that require the brake to be engaged to
prevent the load from falling. Refer to the quick Pulling applications:
selection guide earlier in this section. Because of the 3.5:1 design criteria and
the first layer rating, the ratings for pulling
a. Choose a winch with a lifting capacity equal applications are higher for the same winch.
to or greater than your application load. Choose a winch based on capacity, speed
Tip: Consider using a pulley and distance to be pulled. Manual band
to increase capacity, reduce brakes and clutches are popular configu-
speed, and for better load rations, but each application has its own
Winch capacity:
control. specific requirements. Again, consider
Winches can lift or pull the highest loads
pulleys to increase pulling capacity.
at the first layer, and can lift/pull the least
at the top layer. This is due to the “torque
Air supply and consumption:
arm” effect of the rope spooling on the
b. Make sure the average speed meets your All IR winches are rated at 90 psig (6.3
winch drum. The closer the load is to the
criteria for cycle time. kg/m2) inlet pressure when the winch
drum, the easier it is for the winch to turn
is running. The volume of air required is
and move the load. The further away the
c. Wire rope selection is based on a 5:1 design expressed in cubic feet per minute (cfm) or
load is from the drum, the harder it is for
factor and an 18:1 D/d ratio. cubic meters per minute (m3/min). Refer
the winch to turn.
The 18:1 D/d ratio is an ANSI / ASME B30-7 to the charts for air consumption data
recommendation and is calculated as D + d / d for specific models. Compressor output
Winch speed:
where D = winch barrel diameter and d = wire must equal air consumption for continu-
Winches generally move the load fastest at
rope size. The higher the ratio, the longer the ous operation. Intermittent operation and/
the top layer and slowest at the first layer.
wire rope life. As a guideline, this ratio should or air storage facilities will allow the use of
Think of your old record player. If you put
never go below 15:1. The use of 6 x 37 rope will smaller compressors. Hoses and fittings
a penny near the center of the record, it
increase flexibility. should be sized equal to or preferably one
would simply spin at the same rate as the
size larger than the winch inlet. Strainers,
record. But if you put it near the outside Tip: Winches with lower gear
lubricators, drum guards, filters and regula-
edge, it would fly off. This is because the ratios overhaul better; that is,
tors are recommended based on air quality
outer diameter of the record is travelling the load will run them
and the application. Mufflers and kits for
faster than the inner diameter. The same backwards in a controlled
piping away the exhaust are always sug-
is true for a winch drum, and consequently descent with the throttle off.
www.lgh-usa.com | Pulling
gested for operator safety and comfort.
the wire rope. By applying the manual band
brake, exceptional spotting
Follow these guidelines to choose can be achieved. Auto brakes
the correct utility winch for are always recommended
your application: with remote control operation.
First, consider these three fundamental
questions:
1. How much is to be lifted, pulled, or
tensioned?
d. Either manual or automatic brakes are suit-
able, although automatic brakes are recom-
mended for lifting applications.
Lifting: ANSI/ASME B30.16 Allowable Rated Line Pulls (5:1 Design Factor)
First Layer Mid Layer Top Layer Average Flow
Model Capacity Speed Capacity Speed Capacity Speed Required
lbs. kg fpm m/min. lbs. kg fpm m/min. lbs. kg fpm m/min. cfm m3/min.
LS150R 455 207 103 31 380 173 115 35 330 150 138 42 78 2.2
LS300R 840 382 56 17 740 336 63 19 660 300 69 21 78 2.2
BU7A 1,200 545 36 11 1,000 454 43 13 1,000 454 39 12 50 1.4
LS600R 1,680 764 26 8 1,480 673 30 9 1,325 600 34 10 78 2.2
EU, EUL 2,100 955 62 19 2,000 909 68 21 2,000 909 64 20 100 2.8
LS1500R (1) 4,000 1,818 19 6 3,600 1,636 21 6 3,300 1,500 23 7 125 3.5
FA2B 5,000 2,273 79 24 4,000 1,818 96 29 3,200 1,455 122 37 350 9.9
FA2.5A 5,000 2,273 119 36 5,000 2,273 114 35 4,100 1,864 141 43 700 19.8
HU40A 5,000 2,273 44 14 4,000 1,818 57 18 3,200 1,455 70 22 291 8.2
LS2000R 6,200 2,818 47 14 5,150 2,341 56 17 4,400 2,000 66 20 354 10.0
FA2 6,600 3,000 31 9 5,200 2,364 40 12 4,400 2,000 47 14 280 7.9
FA2.5 7,000 3,182 97 30 5,800 2,636 117 36 5,000 2,273 132 40 700 19.8
FA5A 11,400 5,182 40 12 10,000 4,545 50 15 8,000 3,636 62 19 700 19.8
FA5T 12,500 5,682 47 14 11,300 5,136 52 16 8,400 3,818 70 21 700 19.8
FA5 12,500 5,682 47 14 12,500 5,682 48 15 11,000 5,000 54 16 700 19.8
LS5000R 15,600 7,091 23 7 12,900 5,864 28 9 11,000 5,000 33 10 354 10.0
FA7T 18,880 8,545 32 10 16,700 7,591 37 11 12,600 5,727 48 15 750 21.2
FA7 18,800 8,545 32 10 18,800 8,545 33 10 15,400 7,000 40 12 750 21.2
FA10 27,200 12,364 28 9 27,100 12,319 19 6 22,000 10,000 23 7 800 22.7
Green shading reflects rental inventory.
Pulling: ANSI/ASME B30.7 Allowable Rated Line Pulls (3.5:1 Design Factor)
First Layer Mid Layer Top Layer Average Flow
Model Capacity Speed Capacity Speed Capacity Speed Required
lbs. kg fpm m/min. lbs. kg fpm m/min. lbs. kg fpm m/min. cfm m3/min.
BU7A 1,500 682 26 8 1,200 545 34 10 1,000 454 39 12 50 1.4
PS1000R 2,200 1,000 15 5 1,950 886 17 5 1,740 791 19 6 78 2.2
EU, EUL 3,000 1,364 45 14 2,600 1,182 49 15 2,000 909 64 20 100 2.8
FA2B 5,100 2,318 76 23 4,000 1,818 96 29 3,200 1,455 122 37 350 9.9
PS2400R (1) 5,280 2,400 12 4 4,800 2,182 13 4 4,370 1,986 14 4 125 3.5
FA2 6,800 3,091 29 9 5,400 2,455 37 11 4,500 2,045 44 13 280 7.9
FA2.5A 7,100 3,227 67 20 6,400 2,909 42 13 5,400 2,455 45 14 700 19.8
FA2.5 8,000 3,636 79 24 6,600 3,000 42 13 5,300 2,409 119 36 700 19.8
HU40A 5,100 2,318 42 13 4,000 1,818 54 17 3,200 1,455 68 21 291 8.2
PS4000R 8,800 4,000 13 4 7,300 3,318 16 5 6,200 2,818 18 5 354 10.0
FA5A 13,100 5,955 26/8 8 10,000 4,545 50 15 8,000 3,636 62 19 700 19.8
Sales@lgh-usa.com | Pulling
Specifications
Nominal Line Recommended Drum Rope Anchor
Rope Size (in.) Motor Av. CFM Pipe Inlet Hose Max Stall Net Weight
Capacity Model Speed Root Diam. Hole Diam.
HP Required Size Size Pull (lbs.) (lbs.)
(lbs.) (fpm) 15:1 18:1 (in.) (in.)
1,000 BU7A 45 1
⁄4 1
⁄4 4 1⁄2 1.6 50 1
⁄2 3
⁄4 3
⁄8 2,000 75
2,000 EU, EUL 55 3
⁄8 3
⁄8 6 4.4 100 3
⁄4 1 9
⁄16 4,500 360, 490
2,500 HU, HUL 110 1
⁄2 3
⁄8 7 11 175 1 3
⁄4 11
⁄16 5,000 562
3,000 H5U, H5UL 150 1
⁄2 3
⁄8 7 14 290 1 1⁄4 1 1⁄2 11
⁄16 7,800 525, 598
3,300 LS1500R 23 10mm 10mm 7 3⁄32 3.3 125 3
⁄4 3
⁄4 10mm 7,000 143
4,000 HU40, HUL40 70 1
⁄2 N/A 7 11 175 1 1 1⁄4 11
⁄16 9,000 525, 600
4,400 FA2 55 3
⁄4 5
⁄8 10 3⁄4 9.4 335 1 1 1⁄4 3
⁄4 9,000 775
5,000 K5U, K5UL 115 5
⁄8 1
⁄2 8 ⁄8
5
19 420 1 ⁄4 1
1 ⁄2 1 11
⁄16 10,500 890
5,000 FA2.5 140 3
⁄4 5
⁄8 10 3⁄4 25 700 1 1⁄4 1 1⁄2 3
⁄4 10,000 1,061
8,000 FA5T 80 1 3
⁄4 15 25 700 1 1⁄4 1 1⁄2 1 24,000 2,065
10,000 K6U, K6UL 55 7
⁄8 3
⁄4 12 3⁄4 24 600 1 1⁄4 1 1⁄2 1 15,000 1,314 | 1,550
11.000 FA5 65 1 3
⁄4 15 25 700 1 1⁄4 1 1⁄2 1 24,000 2,000
12,600 FA7T 50 1 ⁄8 1 7
⁄8 16 25 750 1 ⁄4 1
1 1⁄2 1 1⁄8 36,000 2,300
15,400 FA7 45 1 1⁄8 7
⁄8 16 25 750 1 1⁄4 1 1⁄2 1 1⁄8 36,000 1,977
22,000 FA10 30 1 ⁄8 3
1 ⁄8 1
20 31 800 1 ⁄4 1
1 ⁄2 1
1 ⁄8 3
38,000 2,800
Green shading reflects rental inventory.
www.lgh-usa.com | Pulling
HU40
K5U
Dimensions Dimensions
D E A B C D E
A B C Model
Model Air Inlet Exhaust in. in. in. in. in.
in. in. in.
Pipe Tap Pipe tap
www.lgh-usa.com | Pulling
K6U 46 1⁄2 12 26 7⁄8 10 3⁄4 9 1⁄4
HU 32 ⁄8
3
7 ⁄8
1
22 ⁄16
3
1 NPT 1 ⁄4 NPT
1
K6UL 58 1⁄2 24 38 7⁄8 16 3⁄4 15 1⁄4
HUL 40 11⁄16 15 3⁄16 30 3⁄8 1 NPT 1 1⁄4 NPT Note: Dimensions are subject to change. Please contact factory for certified prints.
Green shading reflects rental inventory.
H5U 32 7⁄8 7 1⁄8 22 5⁄16 1 1⁄4 NPT 1 1⁄2 NPT*
H5UL 40 ⁄16
15
15 ⁄16
13
30 ⁄8
3
1 ⁄4 NPT
1
1 1⁄2 NPT*
HU40 32 5⁄8 7 1⁄8 22 3⁄16 1 NPT 1 1⁄4 NPT
HUL40 40 ⁄16
11
15 ⁄16
3
30 ⁄8
3
1 NPT 1 1⁄4 NPT
*Remote control units 1 1/4” NPT.
Note: Dimensions are subject to change. Please contact factory for certified prints.
Green shading reflects rental inventory.
Dimensions
Drum
with Disc Brake Only with Manual Drum Brake Only with Manual and Disc Brake
Length
Model A B C D B C D B C D
in. mm in. mm in. mm in. mm in. mm in. mm in. mm in. mm in. mm in. mm
FA2.5A
FA2.5A-S 7 178 38.44 976 9.55 243 4.78 121 37.64 956 12.31 313 7.5 191 41.19 1,046 12.31 313 7.5 191
FA2.5A-M 13.5 343 44.94 1,141 16.05 408 8.03 204 44.14 1,121 18.81 478 10.8 274 47.69 1,211 18.81 478 10.8 274
FA2.5A-L 20 508 51.44 1,306 22.55 573 11.28 286 50.64 1,286 25.31 643 14 356 54.19 1,376 25.31 643 14 356
FA2.5A-R 24 610 55.44 1,408 26.55 674 13.28 337 54.64 1,388 29.31 744 16 406 58.19 1,478 29.31 744 16 406
FA5A
FA5A-SX 15 381 46.50 1,181 17.89 454 8.94 227 43 1,092 17.89 454 10.5 266 46.5 1,181 17.89 454 10.5 266
FA5A-LX 27 686 58.50 1,486 29.89 759 14.94 379 55 1,397 29.89 759 16.5 419 58.5 1,486 29.89 759 16.5 419
Note: Drum lengths for the FA5A-SM = 12 in. (305 mm), and FA5A-LM = 24 in. (610 mm).
Green shading reflects rental inventory.
Standard Configuration Open Front Configuration (Option H) Standard Configuration Open Front Configuration (Option H)
Standard Features:
• Automatic disc brake or manual band brake
• Corrosion resistant, marine duty “Blue” fasteners
• New self-cleaning K5C2 control valve improves flow and performance,
has more stainless steel and polymer corrosion resistant parts, and is
totally interchangeable with previous designs. 100% natural gas / sour
gas compatible.
• Easy to install wedge type self-tightening rope anchor
• Powerful 5 piston air motor
Construction:
Safety is built In: • Designed to meet the space and performance requirements of
• Meets ASME B30.7 safety standards Classic winches
• “Lift and shift” throttle lever prevents accidental throttle movement
• Throttle lever returns to OFF position and locks when released Options:
• Disc brake is fully automatic and self-adjusting • Corrosion resistant marine grade coating system: Sandblast to
• Wedge type, self tightening-rope anchor provides 80% of rope breaking white metal finish and carbozinc primer with Marine 812 finish
strength • Band brakes – manual and automatic
• Remote controls
Reliability: • Construction cages
• Open frame configurations
• Maximum external corrosion protection against marine and other envi-
• Foot print base with K6U and K6UL bolt pattern for FA5A
ronments is provided as standard.
• Free spool clutch
• Automatic oil bath disc brake has high thermal duty. Suitable for de-
• Tensioning manifold
manding applications.
• Drum guard
• Marine grade alloys and stainless steel components make the valve
• Under wound configuration
• Chest corrosion resistant and maintenance free. • CE package
Performance:
Wire Rope Storage Capacity
• Superior load spotting control Length of Drum in. (mm)
Rope Diam-
• Positive braking action with automatic disc brake eter S M L R
7 (178) 13 1/2 (343) 20 (508) 24 (610)
Specifications* in. mm ft. m ft. m ft. m ft. m
Rated Mid Layer Line Pull, 5:1 DF 5,000 lbs. 2,273 kg 10,000 lbs. 4,545 kg 3
⁄8 9 593 181 1,176 359 1,758 536 2,116 645
www.lgh-usa.com | Pulling
Rated Mid Layer Line Speed 114 fpm 35 m/min. 32 fpm 10 m/min. ⁄16
7
11 460 140 915 279 1,371 418 1,651 503
Top (6th) Layer Line Pull, 5:1 DF 4,100 lbs. 1,860 kg 8,000 lbs. 3,629 kg 1
⁄2 13 356 109 712 217 1,068 326 1,287 392
Top (6th) Layer Line Speed 141 fpm 43 m/min. 43 fpm 13 m/min. 5
⁄8 16 206 63 416 127 625 191 754 230
Max. Stall at First Layer 10,400 lbs. 4,727 kg 17,000 lbs. 7,727 kg Short Drum Long Drum
Drum Root Diameter 9.25 in. 235 mm 12.75 in. 324 mm 12 (305) (1) 15 (381) (2) 24 (610) (1) 27 (686) (2)
Specifications
Performance Based on 90 psi (6.3 bar) Air Inlet Pressure with Motor Running
Utility Rating 5:1 Design Factor Avg. Air Consumption Maximum
Drum Length
Top Layer Top Layer at rated Load Stall Pull Pipe Inlet Size Hose Size Ship Weight
Model A
Line Pull Line Speed @90 psi (6.3 bar) 1st Layer
lbs. kg fpm m/min. in. mm hp scfm m3/min. lbs. kg in. mm in. mm lbs. kg
FA2-24 4,400 2,000 47 14 24 610 9.4 335 9.5 9,000 4,091 1 1⁄4 32 1 1⁄4 32 825 374
FA2.5-24 5,000 2,273 132 40 24 610 25 700 19.9 10,000 4,545 1 1⁄4 32 1 1⁄2 38 1,061 481
FA5-24 11,000 5,000 54 16 24 610 25 700 19.9 24,000 10,909 1 ⁄41
32 1 ⁄2
1
38 1,872 849
FA5T-24 8,400 3,818 70 21 24 610 25 700 19.9 24,000 10,909 1 1⁄4 32 1 1⁄2 38 2,153 977
FA7-24 15,400 7,000 40 12 24 610 25 750 21.3 36,000 16,364 1 ⁄41
32 1 ⁄2
1
38 2,205 1,000
FA7T-24 12,600 5,727 48 15 24 610 25 750 21.3 36,000 16,364 1 1⁄4 32 1 1⁄2 38 2,335 1,059
FA7TGL-42 3,400 1,545 152 46 42 1,067 25 750 21.3 10,000 4,545 1 1⁄4 32 1 1⁄2 38 2,981 1,352
FA7TPL-42 10,200 4,636 60 18 42 1,067 25 750 21.3 36,000 16,364 1 ⁄41
32 1 ⁄2
1
38 2,850 1,293
FA10-24 22,000 10,000 23 7 24 610 31 800 22.7 38,000 17,273 1 1⁄4 32 1 1⁄2 38 3,200 1,451
Green shading reflects rental inventory.
FA5
www.lgh-usa.com | Pulling
www.lgh-usa.com | Pulling
Dimensions are for reference only and subject to change without notice.
Load Rating 1st Layer 18,000 lbs. 18,000 lbs. 18,000 lbs.
Load Rating Mid-Drum 14,000 lbs. 14,000 lbs. 14,000 lbs.
Load Rating Full Drum 11,500 lbs. 11,500 lbs. 11,500 lbs.
Line Speed 1st Layer 30 fpm 30 fpm 30 fpm
TA5 Series Dimensions
Line Speed Mid-Drum 39 fpm 39 fpm 39 fpm
Item TA5-16MX1 TA5-24MX1 TA5-30MX1
Line Speed Full Drum 47 fpm 47 fpm 47 fpm
A 57 in. 65 in. 71 in.
Drum Capacity 1st Layer 72 ft. 120 ft. 150 ft.
C 10.53 in. 12.78 in. 17.03 in.
Drum Capacity Mid-Drum 360 ft. 550 ft. 680 ft.
F 7.75 in. 7.75 in. 7.75 in.
Drum Capacity Full Drum 810 ft. 1,210 ft. 1,520 ft.
H 34.50 in. 34.50 in. 34.50 in.
Input HP 17.8 hp 17.8 hp 17.8 hp
J 35.50 in. 43.50 in. 49.50 in.
Max. Stall Pull 1st Layer 33,000 lbs. 33,000 lbs. 33,000 lbs.
K 4.03 in. 5.78 in. 4.53 in.
Wire Rope Diameter .75 in. .75 in. .75 in.
Pressure 90 psi 90 psi 90 psi
L 9.00 in. 10.50 in. 10.00 in.
Flow 550 scfm 550 scfm 550 scfm W 16.00 in. 24.00 in. 30.00 in.
Pipe Inlet Size 1.5 in. 1.5 in. 1.5 in. No. of Bolt
8 8 10
Holes
Hose Size 1.5 in. 1.5 in. 1.5 in.
Y1 32.50 in. 32.50 in. 32.50 in.
Approximate Ship Weight 2,585 lbs. 2,745 lbs. 2,870 lbs.
Y2 48.00 in. 48.00 in. 48.00 in.
Green shading reflects rental inventory.
Z1 224º 224º 224º
Load Rating 1st Layer 23,600 lbs. 23,600 lbs. 23,600 lbs.
Load Rating Mid-Drum 19,000 lbs. 19,000 lbs. 19,000 lbs.
Load Rating Full Drum 15,900 lbs. 15,900 lbs. 15,900 lbs.
Line Speed 1st Layer 19 fpm 19 fpm 19 fpm
Line Speed Mid-Drum 24 fpm 24 fpm 24 fpm
Line Speed Full Drum 29 fpm 29 fpm 29 fpm TA7 Series Dimensions
Drum Capacity 1st Layer 120 ft. 160 ft. 190 ft. Item TA7-24MX1 TA7-30MX1 TA7-36MX1
Drum Capacity Mid-Drum 520 ft. 650 ft. 780 ft. A 69 in. 75 in. 81 in.
Drum Capacity Full Drum 1,150 ft. 1,440 ft. 1,730 ft. C 15.41 in. 17.41 in. 19.41 in.
Input HP 14.4 hp 14.4 hp 14.4 hp F 9.25 in. 9.25 in. 9.25 in.
Max. Stall Pull 1st Layer 38,000 lbs. 38,000 lbs. 38,000 lbs. H 37.00 in. 37.00 in. 37.00 in.
Wire Rope Diameter .88 in. .88 in. .88 in. J 47 in. 53 in. 59 in.
Pressure 90 psi 90 psi 90 psi K 5.38 in. 6.38 in. 7.38 in.
Flow 550 scfm 550 scfm 550 scfm L 9.00 in. 10.00 in. 11.00 in.
Pipe Inlet Size 1.5 in. 1.5 in. 1.5 in. W 24.00 in. 30.00 in. 36.00 in.
Hose Size 1.5 in. 1.5 in. 1.5 in. Y1 32.00 in. 32.00 in. 32.00 in.
Approximate Ship Weight 3,600 lbs. 3,765 lbs. 3,965 lbs. Y2 51.00 in. 51.00 in. 51.00 in.
Green shading reflects rental inventory.
Z1 210º 210º 210º
www.lgh-usa.com | Pulling
Ø O.63 (Ø 16)
0.59 (15)
Ø 161.14 (Ø 410)
Ø 7.09 (Ø 180)
2.87 (73)
OIL PLUG
1.46 (37)
ROPE ENTRY
AIR INLET
CLUTCH LEVER
TOP LAYER
Rc1 BRAKE LEVER
7.80 (198)
6.16 (156.5)
24.29 (617)
DRUM CENTER
EXHAUST
12.01 (305)
www.lgh-usa.com | Pulling
NOTE:
AIR PRESSURE MOTOR POWER ROPE PULL ROPE SPEED AIR CONSUMPTION ROPE CAPACITY WEIGHT
psi (MPa) hp (kW) 1b (kN) fpm (m/min) cfm (Nm3 / min) Ø i n x f t (m) l b (kg)
ABOUT
90 (0.62) 9.6 (7.15) 4400 (20) 62 (19) 191 (5.4)
Specifications (at Half Drum)
1/2 x 750 (230)
631
(287)
Air Pressure Motor Power Rope Pull Rope Speed Air Consumption Rope Capacity Weight
psi (MPa) hp (kW) 1 b (kN) fpm (m/min) cfm (Nm3 / min) 0 in x ft (m) lbs. (kg)
90 (0.62) 9.6 (7.15) 4,400 (20) 62 (19) 191 (5.4) 1
⁄2 x 750 (230) About 631 (287)
Note: Dimensions are inches, ( ) metric mm.
Green shading reflects rental inventory.
122
Lifting Gear Hire Corporation
U-8 Series
Specifications
Sales@lgh-usa.com | Pulling
U-8A-15 1,500 40 fpm 125 cfm @ 90 psi 650 400 240 165 80
Green shading reflects rental inventory.
TM
Dimensions
B C D E
Model
in. in. in. in.
12” DIA 32 27 35 53.78
42” DIA 52 57 65 83.78
Note: Dimensions are subject to change.
Please contact factory for certified prints.
Green shading reflects rental inventory.
Specifications
Accumulated Max Hp
Capacity Pitch Dia Flange Stall Line Pull Start Line Pull
Layer No. Capacity Line pull Speed FPM AT F.S.
(ft) (in) Clearance (lbs) (lbs)
(ft) (lbs) (fpm)
1 56 56 16.9 36,899 30.4 8.4 56,320 44,039 72
www.lgh-usa.com | Pulling
5 76 331 22.9 27,142 41.3 5.4 41,428 32,394 98
9’ - 0”
4’ - 7”
4’ - 0”
3’ - 10.5”
Sales@lgh-usa.com | Pulling
MOUNTING OPTION 1
THERN TA2 - 16 SERIES WINCH
5’ - 10”
9’ - 0” 4’ - 7”
Measurements in this diagram reflect the dimensions of the winch frame ONLY.
Refer to the dimension table for more information.
87.75
www.lgh-usa.com | Pulling
74.00
87.75
Measurements in this diagram reflect the dimensions of the winch frame ONLY. Refer to the dimension table for more information.
87.75
Sales@lgh-usa.com | Pulling
74.00
87.75
Measurements in this diagram reflect the dimensions of the winch frame ONLY. Refer to the dimension table for more information.