Documente Academic
Documente Profesional
Documente Cultură
Version: V2.00
ZTE CORPORATION
NO. 55, Hi-tech Road South, ShenZhen, P.R.China
Postcode: 518057
Tel: +86-755-26771900
Fax: +86-755-26770801
URL: http://ensupport.zte.com.cn
E-mail: support@zte.com.cn
LEGAL INFORMATION
Copyright © 2011 ZTE CORPORATION.
The contents of this document are protected by copyright laws and international treaties. Any reproduction or
distribution of this document or any portion of this document, in any form by any means, without the prior written
consent of ZTE CORPORATION is prohibited. Additionally, the contents of this document are protected by
contractual confidentiality obligations.
All company, brand and product names are trade or service marks, or registered trade or service marks, of ZTE
CORPORATION or of their respective owners.
This document is provided “as is”, and all express, implied, or statutory warranties, representations or conditions
are disclaimed, including without limitation any implied warranty of merchantability, fitness for a particular purpose,
title or non-infringement. ZTE CORPORATION and its licensors shall not be liable for damages resulting from the
use of or reliance on the information contained herein.
ZTE CORPORATION or its licensors may have current or pending intellectual property rights or applications
covering the subject matter of this document. Except as expressly provided in any written license between ZTE
CORPORATION and its licensee, the user of this document shall not acquire any license to the subject matter
herein.
ZTE CORPORATION reserves the right to upgrade or make technical change to this product without further notice.
Users may visit ZTE technical support website http://ensupport.zte.com.cn to inquire related information.
The ultimate right to interpret this product resides in ZTE CORPORATION.
Revision History
I
II
About This Manual
Purpose
This manual gives introduction on the product external interfaces, indicators and modules.
Intended Audience
l Hardware Installation Engineer
l Operation and Maintenance Engineer
Chapter Summary
I
II
Chapter 1
Product Introduction
Table of Contents
Product Appearance...................................................................................................1-1
Product External Interfaces ........................................................................................1-1
Product Indicators ......................................................................................................1-3
1-1
Table 1-1 shows the detailed description of all the external interfaces.
1-2
8 Grounding Terminal -
1-3
RUN Green Running status l Blinking every 1.5 second: physical link
in the process of initialization
l Blinking every 0.07 second: the link
between eBBU and eRRU is in the
process of establishment, or the link is
broken
l Blinking every 0.3 second: device is in
good state
1-4
OPT1 Green Optical interface running l Solid ON: physical link is good, logical
indicator link is abnormal
l OFF: physical link is abnormal
l Blinking every 0.3 second: interface is
in good state
OPT2 Green Optical interface running l Solid ON: physical link is good, logical
indicator link is abnormal
l OFF: physical link is abnormal
l Blinking every 0.3 second: interface is
in good state
VSWR1 Red Transmission channel 0 l Solid ON: there are VSWR alarms
VSWR indicator l OFF: there is no VSWR alarm
VSWR2 Red Transmission channel 1 l Solid ON: there are VSWR alarms
VSWR indicator l OFF: there is no VSWR alarm
1-5
1-6
R8882 comprises TRM, PAD, FLD, and EPBA, as shown in Table 2-1.
Dual power amplification Provide the amplification function of RF signals on two chan-
PAD
unit nels
2-1
TRM
l Optical interface processing
l Clock processing
l Uplink and downlink processing
l Frequency hopping
l Adaptive modulation rate
l Monitoring
l Indication
l Power supply and on-off switch
l Reset switch
l Interfaces for connecting external devices
PAD
l Amplifies downlink radio signals received from the TRM, and outputs the amplified
signals to the FLD.
l Amplifies four signals received from the FLD with the LNA, and then sends the
amplified signals to the TRM.
l Provides a pre-distortion feedback interface to the TRM.
l Provides an interface to the TRM for Voltage Standing Wave Ratio (VSWR) detection
(forward power detection).
l Supports separate switch-off.
l Supports Inner-module temperature detection.
l Provides read and write interfaces for module inventory management.
FLD
l Transmits and receives uplink and downlink signals in duplex mode.
l Suppresses spurious emission on the downlink to get acceptable out-band Tx
spurious emission required by the system and related protocol.
l Suppresses interference signals on the uplink to achieve a satisfied noise coefficient.
EPB
l Provides the lightning protection for -48 V power supply.
2-2
2-3
2-4
Power cable Connects the ZXSDR R8882 One end is circular 6-core
GUL1812 power interface to cable connector (hole) with
the power supply equipment plastic cover, the other end is
interface reserved for power cable. The
length of cable is based on the
engineering survey.
Grounding cable Connects one ZXSDR R8882 The grounding cable is made
GUL1812 ground bolt to the up of strands of flame-retardant
copper bar wire. The cross sectional area
of ZXSDR R8882 GUL1812
grounding cable is 25 mm2.
Copper lugs are crimped at both
ends of the grounding cable
.
Fiber There are two types of ZXSDR There are two types of fiber:
R8882 GUL1812 fiber: BBU BBU connection and ZXSDR
connection and ZXSDR R8882 R8882 GUL1812 cascading.
GUL1812 cascading.
Environment monitor cable Connects the ZXSDR R8882 For the environment monitor
GUL1812 environment monitor cable, end A is PIN header.
interface to the external monitor End B, with 3m length in total,
components or the dry contact. is made depending on the field
engineering conditions.
AISG control cable Connects the ZXSDR R8882 AISG is used to control the
GUL1812 debugging interface electrical-adjustment antenna.
(AISG) to the control interface of
electrical-adjustment antenna.
3-1
Antenna jumper Connects ZXSDR R8882 The RF jumper usually uses the
GUL1812 to main feeder finished 1/2″ jumper
with 2m length. The jumper
can be customized depending
on actual conditions. One end
of the jumper is N connector
(male) and the other end is DIN
connector (female).
3-2