Sunteți pe pagina 1din 12

Cat Electronic Technician 2016C v1.

0
Product Status Report

20/12/2017 10:56 AM

Product Status Report


Parameter Value
Product ID B9K00497
Equipment ID B9K00497
Comments

Trans/Chassis 24M (HKY01200)


Parameter Value
Product ID B9K00497
Equipment ID B9K00497
Transmission Serial Number HKY01200
ECM Part Number 3045687-02
ECM Serial Number 09426150MS
ECM Location Code 1
Software Group Part Number 5108192-00
Software Group Release Date APR2016
Software Group Description 24 MG Chassis/Trans

Logged Diagnostic Codes [Diagnostic Clock = 19263.5824 hours] - Trans/Chassis 24M


(HKY01200)
Code Description Occ. First Last
No Logged
Diagnostic
Codes

Logged Event Codes [Diagnostic Clock = 19263.5826 hours] - Trans/Chassis 24M (HKY01200)
Code Description Occ. First Last
E258 (3) No steering detected with command given 5 19179 19215
E334 (2) Low Auto Lube Pressure 127 18778 19263

Active Diagnostic Codes - Trans/Chassis 24M (HKY01200)


Code Description
No Active
Diagnostic
Codes

Active Event Codes - Trans/Chassis 24M (HKY01200)


Code Description
No Active
Event Codes
Current Totals - Trans/Chassis 24M (HKY01200)
Description Value Unit
Total Operating Hours 19264 hours
Total Hours Coasting In Neutral 70 hours
Parking Brake Pressure Switch 20094
Cycles
Parking Brake Solenoid Cycles 20098
Starter Relay Cycles 7863
Service Brake Pedal Switch 676680
Cycles
Machine Idle Time 2262.60 hours
Number of Cold Temperature 6
Transmission Filter Bypasses
Total Cold Temperature 0 hours
Transmission Oil Filter Bypass
Hours
Total Operating Hours While 0.0 hours
Compression Brake Disabled

Configuration - Trans/Chassis 24M (HKY01200)


Description Value Unit
Transmission Serial Number HKY01200
Transmission Maximum Forward Gear 6
Transmission Maximum Reverse Gear 3
Transmission Initial Forward Gear 1
Transmission Initial Reverse Gear 1
Transmission Maximum Forward Autoshift 4
Gear
Transmission Minimum Forward Autoshift 4
Gear
Transmission Minimum Reverse Autoshift 3
Gear
Transmission Maximum Reverse Autoshift 3
Gear
Machine Speed Correction Factor 0.0000 %
Auto Lube System Installation Status Installed
Auto Lube Interval 5 min
Auto Lube Duration 120 sec
Minimum Auto Lube Pressure 17237 kPa
Configuration
Compression Brake Switch Type Momentary
Configuration
Battery Cable Shield Monitoring System Not Installed
Installation
Hydraulic Oil Level Warning System Not Installed
Installation Status
CAN Communication Protocol Write Unavailable
Security
CAN Communication Protocol Read Unavailable
Security
Total Tattletale 0
Shift Count Matrix - Trans/Chassis 24M (HKY01200)
To N R1 R2 R3 1 2 3 4 5 6
From
N --- 140748 7840 58 196117 5853 2204 735 720 0
R1 69371 --- 67308 0 7802 0 2 0 0 0
R2 70455 3089 --- 2013 14 10 839 0 0 0
R3 1356 0 714 --- 0 0 0 0 0 0
1 41423 646 1 0 --- 178883 466 233 14 0
2 72590 1 294 0 17026 --- 154415 0 0 0
3 72620 3 264 0 482 59584 --- 78085 0 0
4 24523 1 0 0 233 0 53130 --- 23428 0
5 1852 0 2 0 0 0 0 22274 --- 1679
6 34 0 0 0 0 0 0 0 1645 ---

Counters - Trans/Chassis 24M (HKY01200)


Description Value
Parking Brake Pressure Switch Cycles 20094
Parking Brake Solenoid Cycles 20098
Starter Relay Cycles 7863
Service Brake Pedal Switch Cycles 676680
Number of Cold Temperature Transmission 6
Filter Bypasses
Total Overspeed Protective Upshift Count Unavailable

VIMS Main Module (B9K00497)


Parameter Value
Product ID B9K00497
Equipment ID
ECM Part Number 4174722-00
ECM Serial Number 0463F004CR
Software Group Part Number 4619131-00
Software Group Release Date FEB2016
Software Group Description A5N2_VIMS_2015A_PROD_1.0
Application Software Part Number 4854413-00

Logged Diagnostic Codes [Diagnostic Clock = 19263.5826 hours] - VIMS Main Module
(B9K00497)
Code Description Occ. First Last
No Logged
Diagnostic
Codes

Logged Event Codes [Diagnostic Clock = 19263.5826 hours] - VIMS Main Module (B9K00497)
Code Description Occ. First Last
E558 (1) Snapshot Stored 11 18001 19103
E2139 (1) Snapshot Memory Full 10 18017 19113

Active Diagnostic Codes - VIMS Main Module (B9K00497)


Code Description
No Active
Diagnostic
Codes

Active Event Codes - VIMS Main Module (B9K00497)


Code Description
E558 (1) Snapshot Stored
E2139 (1) Snapshot Memory Full

Current Totals - VIMS Main Module (B9K00497)


Description Value Unit
Total Operating Hours 19264 hours
Lifetime Total Payload Weight Unavailable tonne
Machine Loaded Travel Hours Unavailable hours
Machine Loaded Distance Unavailable km
Traveled
Total Load Count Unavailable

Configuration - VIMS Main Module (B9K00497)


Description Value Unit
Data Acquisition System Installation Status Installed
Data Acquisition System Customer Enable Enabled
Status
Data Acquisition System Temporary 0 min
Installation Time Remaining
Customer Password #1 ********
Customer Password #2 ********
Product ID B9K00497
Equipment ID
External Service Lamp Installation Installed
Configuration
External Service Lamp Display Mode Snapshot Occurred
Setting
Telemetry Port Selection Serial Port #2
TMAC Protocol Port Selection Disabled
Ethernet Media Access Control (MAC) 30:30:3A:30:41:3A
Address
Internet Protocol Host Name VIMS3G
Internet Protocol (IPv4) Address 0.0.0.0
Internet Protocol (IPv4) Network Mask 0.0.0.0
Network Default Gateway Internet Protocol 0.0.0.0
(IPv4) Address
Web Server Administrator Password Unavailable
Dynamic Host Configuration Protocol Disabled
(DHCP) Enable Status
Machine Payload Control System Unavailable
Installation Status
Target Payload Unavailable tonne
Payload Overload Limit Unavailable %
Green TPMS Lamp Installation Unavailable
Configuration
Red TPMS Lamp Installation Configuration Unavailable
Truck Payload Last Pass Indicator Enable Unavailable
Status
External Payload Indicator Configuration Unavailable
OHT Payload Re-weigh Unavailable
Front Axle Strut Pressure to Payload Unavailable
Weight Ratio Configuration
Road Analysis System Installation Status Unavailable
Road Analysis Severity Selection Unavailable
Tire Analysis System Installation Status Unavailable
Tire Analysis System Temporary Unavailable
Installation Status
Tire Analysis System Customer Enable Unavailable
Status
Tire Analysis System Temporary Unavailable min
Installation Time Remaining
Machine Weight-Speed Averaging Duration Unavailable hours
Empty Machine Weight Unavailable tonne
Empty Machine Rear Axle Weight Unavailable %
Distribution
Loaded Machine Rear Axle Weight Unavailable %
Distribution
Machine Speed Limit Activation Front Tires Unavailable TKPH
Weight-Speed Threshold
Machine Speed Limit Deactivation Front Unavailable TKPH
Tires Weight-Speed Threshold
Machine Speed Limit Activation Rear Tires Unavailable TKPH
Weight-Speed Threshold
Machine Speed Limit Deactivation Rear Unavailable TKPH
Tires Weight-Speed Threshold
Machine Tire Weight-Speed Machine Unavailable km/h
Speed Limit

Implement 24M (B9K00497)


Parameter Value
Product ID B9K00497
Equipment ID B9K00497
ECM Part Number 3045687-02
ECM Serial Number 22116209MS
ECM Location Code 2
Software Group Part Number 4750242-00
Software Group Release Date AUG2015
Software Group Description 24 MG Master Impl Cntl

Logged Diagnostic Codes [Diagnostic Clock = 19263.5824 hours] - Implement 24M (B9K00497)
Code Description Occ. First Last
No Logged
Diagnostic
Codes

Logged Event Codes [Diagnostic Clock = 19263.5824 hours] - Implement 24M (B9K00497)
Code Description Occ. First Last
E258 (3) No steering detected with command given 8 19179 19222
E2085 (2) Invalid Articulation Response Detected 7 19177 19252

Active Diagnostic Codes - Implement 24M (B9K00497)


Code Description
No Active
Diagnostic
Codes

Active Event Codes - Implement 24M (B9K00497)


Code Description
No Active
Event Codes

Current Totals - Implement 24M (B9K00497)


Description Value Unit
Total Operating Hours 19264 hours

Configuration - Implement 24M (B9K00497)


Description Value Unit
Steering System Configuration Code 1
Left Steering Cylinder Maximum Extension 1282.5 mm
Length
Right Steering Cylinder Maximum 1282.0 mm
Extension Length
Left Steering Cylinder Minimum Retraction 838.7 mm
Length
Right Steering Cylinder Minimum 837.8 mm
Retraction Length
Left Steering Cylinder Position Sensor 186.1 uSec
Maximum Pulse Duration
Right Steering Cylinder Position Sensor 186.6 uSec
Maximum Pulse Duration
Left Steering Cylinder Position Sensor 26.7 uSec
Minimum Pulse Duration
Right Steering Cylinder Position Sensor 26.8 uSec
Minimum Pulse Duration
Hydraulic Oil Viscosity Rating SAE 10W
Grade Control On Joystick Attachment Disabled
Enable Status
Blade Constant Down Force Installation Not Installed
Status
Ripper AutoStow Enable Status Enabled
Machine Shipping Mode Enable Status Disabled
Blade Pitch Lockout Status Not Locked Out
Blade Sideshift Lockout Status Not Locked Out
Circle Sideshift Lockout Status Not Locked Out
Wheel Lean Lockout Status Not Locked Out
Articulation Lockout Status Not Locked Out
Blade Rotation Angle Limit Enable Status Disabled
Blade Rotation Angle Limit 33.00 Deg
AccuGrade System Installation Status Installed
AccuGrade Enable Status Disabled
AccuGrade Temporary Installation Status Not Installed
Cross Slope Control System Installation Not Installed
Status
Cross Slope Control System Temporary Not Installed
Installation Status
Cross Slope Control System Enable Status Disabled
Blade Cross Slope Angle Offset Switch Unavailable %
Adjustment
Drawbar Length 3794 mm
Blade Width 4.267 meters
Lift Cylinder Ball Stud Distance 1686 mm
CAN Communication Protocol Write Unavailable
Security
CAN Communication Protocol Read Unavailable
Security

Calibration Status - Implement 24M (B9K00497)


Calibration Status Last Successful Completion
Articulation Position Sensor Success 19161.1 hours
Calibration
Auxiliary Valve #1 Port B Success 1.9 hours
Solenoid
Auxiliary Valve #1 Port A Success 1.9 hours
Solenoid
Auxiliary Valve #2 Port B Unknown Never Successfully Calibrated
Solenoid
Auxiliary Valve #2 Port A Unknown Never Successfully Calibrated
Solenoid
Auxiliary Valve #3 Port B Not Calibrated Never Successfully Calibrated
Solenoid
Auxiliary Valve #3 Port A Not Calibrated Never Successfully Calibrated
Solenoid
Auxiliary Valve #4 Port B Not Calibrated Never Successfully Calibrated
Solenoid
Auxiliary Valve #4 Port A Not Calibrated Never Successfully Calibrated
Solenoid
Auxiliary Valve #5 Port B Not Calibrated Never Successfully Calibrated
Solenoid
Auxiliary Valve #5 Port A Not Calibrated Never Successfully Calibrated
Solenoid
Auxiliary Valve #6 Port B Not Calibrated Never Successfully Calibrated
Solenoid
Auxiliary Valve #6 Port A Not Calibrated Never Successfully Calibrated
Solenoid
Blade Left Constant Down Not Calibrated Never Successfully Calibrated
Force Control
Blade Right Constant Down Not Calibrated Never Successfully Calibrated
Force Control
Blade Rotation Angle Sensor Unknown Never Successfully Calibrated
Calibration
Left Lift Valve Calibration Unknown Never Successfully Calibrated
Right Lift Valve Calibration Unknown Never Successfully Calibrated
Slope Sensors Calibration Unknown Never Successfully Calibrated
Blade Right Lower Solenoid Success 19160.7 hours
Calibration
Blade Right Lower Float Success 19160.7 hours
Solenoid Calibration
Blade Left Lower Solenoid Success 19160.8 hours
Calibration
Blade Left Lower Float Solenoid Success 19160.8 hours
Calibration
Circle Right Solenoid Success 19160.8 hours
Calibration
Circle Left Solenoid Calibration Success 19160.8 hours
Blade Right Raise Solenoid Success 19160.8 hours
Calibration
Blade Left Raise Solenoid Success 19160.8 hours
Calibration
Blade Sideshift Right Solenoid Success 19160.9 hours
Calibration
Blade Sideshift Left Solenoid Success 19160.9 hours
Calibration
Blade Pitch Forward Solenoid Success 19160.9 hours
Calibration
Blade Pitch Backward Solenoid Success 19160.9 hours
Calibration
Circle Sideshift Right Solenoid Success 19160.9 hours
Calibration
Circle Sideshift Left Solenoid Success 19160.9 hours
Calibration
Articulate Right Solenoid Success 19160.9 hours
Calibration
Articulate Left Solenoid Success 19160.9 hours
Calibration
Wheel Lean Right Solenoid Success 19160.9 hours
Calibration
Wheel Lean Left Solenoid Success 19161.0 hours
Calibration
Steering Cylinder Position Success 19161.1 hours
Sensors Calibration
Arm Steering System/Solenoid Unknown Never Successfully Calibrated
Calibration

C18 24M (TXH02115)


Parameter Value
Equipment ID B9K00497
Engine Serial Number TXH02115
ECM Serial Number 24516134JL
Software Group Part Number 4336931-00
Software Group Release Date NOV12
Software Group Description MG 24M

Logged Diagnostic Codes [Diagnostic Clock = 19263.5699 hours] - C18 24M (TXH02115)
Code Description Occ. First Last
No Logged
Diagnostic
Codes

Logged Event Codes [Diagnostic Clock = 19263.5699 hours] - C18 24M (TXH02115)
Code Description Occ. First Last
E360 (3) Low Engine Oil Pressure 1 14539 14539
E361 (2) High Engine Coolant Temperature 41 17288 17477
E362 (1) Engine Overspeed 72 12200 18889

Active Diagnostic Codes - C18 24M (TXH02115)


Code Description
No Active
Diagnostic
Codes

Active Event Codes - C18 24M (TXH02115)


Code Description
No Active
Event Codes

Current Totals - C18 24M (TXH02115)


Description Value Unit
Total Operating Hours 19264 hours
Total Fuel 511780 L
Total Max Fuel 1406018 L
Total Idle Time 2128:57 hours
Total Idle Fuel 17275 L
Lifetime Total Engine 1171875964 rev
Revolutions
Engine Starts 6498
Total Engine Idle Shutdown 0
Count
Total Engine Idle Shutdown 0
Overrides Count

Configuration - C18 24M (TXH02115)


Description Value Unit
Equipment ID B9K00497
Engine Serial Number TXH02115
ECM Serial Number 24516134JL
ECM Part Number 2622878-01
Software Group Part Number 4336931-00
Software Group Release Date NOV12
Software Group Description MG 24M
Engine Cooling Fan Map Unavailable
Ether Solenoid Configuration Continuous Flow Solenoid
Engine Warm Up Elevated Idle Feature Enabled
Enable Status
Engine Retarder Enable Command Enabled
Exhaust Temperature Sensor Installation Not Installed
Status
Engine Idle Shutdown Enable Status Disabled
Engine Idle Shutdown Delay Time 5.0 min
FLS -43
FTS 59
Total Tattletale 26

Injector Trim Calibration - C18 24M (TXH02115)


Injector Serial Number File Version
Injector1 000000005A5328709340 0
Injector2 000000005A53283636FC 0
Injector3 000000005A5328698177 0
Injector4 000000005A53282386BD 0
Injector5 000000005A532870975C 0
Injector6 000000005A5328326616 0

Monitoring System - C18 24M (TXH02115)


Description State Trip Point Delay Time
Engine Overspeed
Least Severe (1) Always On 2400 rpm 0 sec
Moderate Severity (2) Always On 2500 rpm 0 sec
High Air Filter
Restriction Pressure
Least Severe (1) Always On 7.5 kPa 0 sec
Moderate Severity (2) Always On 9.0 kPa 0 sec
High Engine Coolant
Temperature
Least Severe (1) Always On 110 Deg C 10 sec
Moderate Severity (2) On 111 Deg C 10 sec
Most Severe (3) Off 111 Deg C 10 sec
High Engine Inlet Air
Temperature
Least Severe (1) Always On 82.0 Deg C 8 sec
Moderate Severity (2) Always On 86.0 Deg C 8 sec
High Fuel Filter
Pressure Restriction
Least Severe (1) On None 3600 sec
Moderate Severity (2) On None 14400 sec
High Fuel Pressure
Least Severe (1) Always On 758.0 kPa 8 sec
High Fuel Temperature
Least Severe (1) Always On 90.0 Deg C 30 sec
Moderate Severity (2) On 91.0 Deg C 10 sec
High Turbo Turbine
Outlet Temperature
Moderate Severity (2) Always On 0 Deg C 15 sec
Most Severe (3) Always On 0 Deg C 15 sec
Low Engine Oil
Pressure
Least Severe (1) Always On None 8 sec
Most Severe (3) Always On None 4 sec

Implement Control #2 (B9K00497)


Parameter Value
Product ID B9K00497
Equipment ID B9K00497
ECM Part Number 3045687-02
ECM Serial Number 21916023MS
ECM Location Code 3
Software Group Part Number 3855563-00
Software Group Release Date SEP2011
Software Group Description Aux Implement Ctrl #1

Logged Diagnostic Codes [Diagnostic Clock = 19263.5826 hours] - Implement Control #2


(B9K00497)
Code Description Occ. First Last
No Logged
Diagnostic
Codes

Logged Event Codes [Diagnostic Clock = 19263.5826 hours] - Implement Control #2 (B9K00497)
Code Description Occ. First Last
No Logged
Event Codes

Active Diagnostic Codes - Implement Control #2 (B9K00497)


Code Description
No Active
Diagnostic
Codes

Active Event Codes - Implement Control #2 (B9K00497)


Code Description
No Active
Event Codes

Configuration - Implement Control #2 (B9K00497)


Description Value Unit
Advanced Machine Security System Not Installed
Installation Status
Total Tattletale 13

Monitor 24M (B9K00497)


Parameter Value
Product ID B9K00497
Equipment ID B9K00497
ECM Part Number 3083869-02
ECM Serial Number 2211B049HL
Software Group Part Number 4465906-00
Software Group Release Date DEC13
Software Group Description Msngr MG

Logged Diagnostic Codes [Diagnostic Clock = 19263.6246 hours] - Monitor 24M (B9K00497)
Code Description Occ. First Last
No Logged
Diagnostic
Codes

Logged Event Codes [Diagnostic Clock = 19263.6249 hours] - Monitor 24M (B9K00497)
Code Description Occ. First Last
No Logged
Event Codes

Active Diagnostic Codes - Monitor 24M (B9K00497)


Code Description
No Active
Diagnostic
Codes

Active Event Codes - Monitor 24M (B9K00497)


Code Description
No Active
Event Codes

Current Totals - Monitor 24M (B9K00497)


Description Value Unit
Total Operating Hours 19264 hours

Configuration - Monitor 24M (B9K00497)


Description Value Unit
Equipment ID B9K00497
Product ID B9K00497
Articulation Gauge Deflection Offset Unavailable %
Display Language Status Unavailable
Information Units Status Unavailable
All Wheel Drive System Installation Status Not Installed

S-ar putea să vă placă și