Documente Academic
Documente Profesional
Documente Cultură
INSTALLATION
and
MAINTENANCE
INSTRUCTIONS
Introduction
Valve Description ................................................................................................................................... 3
Valve Design Features .......................................................................................................................... 3
Flange and Pipe Schedule Compatibility ............................................................................................... 3
Gasket Compatibility .............................................................................................................................. 3
Operating Pressures .............................................................................................................................. 3
Product Identification ............................................................................................................................. 3
Installation Recommendations
Valve Ratings ........................................................................................................................................ 4
Valve Seat Position ............................................................................................................................... 4
Disc Clearances .................................................................................................................................... 4
Opening Rotation ................................................................................................................................... 4
Installation Position ................................................................................................................................ 4
Valve and Flange Preparation ............................................................................................................... 4
Installation Tools .................................................................................................................................... 4
Required Bolting .................................................................................................................................... 4
Unpacking and Storage Instructions ...................................................................................................... 4
Pre-Installation Procedure ..................................................................................................................... 5
Valve Installation Procedure ............................................................................................................ 5 & 6
Flange Bolting Recommendations ......................................................................................................... 7
Maintenance Instructions
Safety Precautions ................................................................................................................................ 8
General Maintenance ............................................................................................................................ 8
Butterfly Valve Disassembly .................................................................................................................. 8
Butterfly Valve Assembly ................................................................................................................. 8 & 9
Check Valve Disassembly ..................................................................................................................... 9
Check Valve Assembly ........................................................................................................................ 10
Ratchet Handle Mounting Procedure .................................................................................................. 10
Manual Gear Mounting Procedure ...................................................................................................... 10
Remote Actuator (Male Drive) Mounting Procedure ............................................................................ 10
Remote Actuator (Female Drive) Mounting Procedure ....................................................................... 10
Parts List .............................................................................................................................................. 11
Centerline Figure Number System ........................................................................................ Back Cover
SECTION 1
Valve Description Gasket Compatibility
The Center Line Resilient Seat Butterfly Valve (RSBFV) is In the Center Line butterfly valve and check valve design, the
designed for use in ANSI Class 150 piping systems and is elastomer seat extends beyond the valve face and provides
available in both Wafer and Lug style body designs. The a leakproof seal between the valve and the mating pipe
standard valve size range available is as follows: flange faces. Gaskets are not needed and should not be
• Series 200 200 psi Standard BFV 2" to 12" used when the valve is installed between standard weld
150 psi Standard BFV 14" to 36" neck or slip-on type flanges.
• Series 205 200 psi Short Neck BFV 2" to 12"
• Series 225 285 psi BFV 2" to 24"
• Series 400 Damper Style BFV 2" to 12"
• Series 800 Check Valve 2" to 24" Operating Pressures
Center Line Series 225 Butterfly Valve are also available All Center Line Series 200 and 205 Butterfly Valves are rated
with an ANSI Class 300 bolt pattern for Lug bodies of sizes at 200 psi bubble tight shut-off for sizes 2" to 12" and 150 psi
2" through 12". bubble tight shut-off for sizes 14" and larger. Center Line
Series 225 Butterfly Valves are rated for bubble tight shut-
Valve Design Features off at 285 psi, while Series 400 Damper Valves which are not
• The unique Center Line seat and disc design insures designed for bubble tight shut-off have a body working
positive valve sealing while maintaining low seating torque. pressure of 200 psi. Center Line Series 800 Check Valves
• All Center Line Butterfly Valve discs are precision ma- are rated at a minimum pressure differential of 25 psi and a
chined to a half ball profile, providing a precise disc to seat maximum pressure differential of 150 psi for bubble tight
relationship. shut-off.
• Center Line's cartridge style seat incorporates an elas-
tomer bonded to a phenolic stabilizing ring, eliminating
elastomer movement and reducing seat tearing or fatigu-
ing due to bunching. Product Identification
• Center Line's basic three bushing design completely Each Center Line valve has an identification tag attached to
isolates the valve shaft from the body, resulting in in- the valve body. Information on this tag includes the valve
creased control of the valve disc, lower valve seating Series Number, materials of construction for the Body, Disc,
torque, and longer valve life. and Seat, and the valve Pressure Rating.
• The Center Line cartridge seat has a much smaller mass
of elastomer than traditional boot seat designs, limiting
seat swell and the accompaning variations in seating
torque.
SECTION 2
Incorrect Correct
Disc opened beyond valve Disc positioned in the
body face. Pipe flanges not almost closed position.
spread sufficiently. Pipe flange spread allows
sufficient room for valve.
Incorrect Correct
Disc in closed position. No flange gaskets used.
Gaskets installed between Disc in the “almost closed”
Gasket
valve and mating flanges. position.
1 13
1 5 15 5
1 5 12 9 8 9
1 3 8 3 8 3 12 3
4 4 7 4 11
4 2 7
10 11 10 7
6 2
6 2 6 16
14 2
Incorrect Correct
Pipe Flanges mis-aligned. Piping aligned.
Uneven torque applied to Thread engagement even
bolting. on both sides of valve.
Bolting and torque recommendations are made without a warranty, and apply only to steel weld-neck or slip-on flanges.
The use of lock washers and/or lubrication with the bolting will affect stated torque values.
5. Remove the check valve plates (2) from the valve insert.
Note the location of the thrust washers (6). These must be
replaced in the same location upon reassembly.
7. Insert taper pin(s) into the disc and set with two or three
sharp blows. Wipe dust shield o-ring with silicone grease
and place over the shaft into the top of the body.
8. If the valve is of dead end service design, insert set screws
through the body into the seat. 8
4
Key
O-Ring 8
1
6
2
Taper Pins
2
6
5
5
1
7
Parts List
, ,
6 Series 200, 205, 225
4 Butterfly Valve
,,
7 Item Description
8 1 Body
6
2 Disc
9 3* Seat 8 11
4 Shaft
3
5* Taper Pin
6 Key
5 7* O-Ring Detail A 5
8 Bushing
7
9 Bushing
See Detail A
10 Bushing
1
2 *Recommended Spare Parts
9
4
10
1
2
Series 800
Check Valve
Item Description 10
3
1* Valve Body
2* Liner (Molded to Item 1)
3 Shaft
Series 400
4 Shaft Plug (Qty. 2)
5 Plate (Qty. 2)
Damper Valve
6 Thrust Washer (Qty. 4) Item Description
7 Spring (Qty. 2)
1 Body
8 Alignment Body
2 Disc
4 9 Set Screw
3 Shaft
10 Plate Travel Stop (14" &
4* Taper Pin
larger only)
5 Key
* Items 1 and 2 Must Be 6* Packing (V-Ring)
3 Ordered Together. 7 Packing Retainer
8 Washer (Qty. 2)
9 Bushing
6 10 Bushing
2 11 Snap Ring
1 7 *Recommended Spare Parts
5 9
7
8
6
4
10
1 2 3 4 5 6 7 8 9
1. Size Code 3. Body Code 7. Bushing Code
2" 02 Cast Iron 1 Bronze 0
21/2" 25 * Ductile Iron 2 PTFE 3
3" 03 Carbon Steel 3 Springs (CLC):
To 316 SS 4 316 SS D
36" 36 Ductile Iron-(A395) G Nitronic 50 F
A395 Epoxy H
A395-HI Epoxy J
2. Series/Style Code Cast Iron-Epoxy S
* Ductile Iron-Epoxy V
200-Wafer A Cast Iron-HI Epoxy D
200-Lug B * Ductile Iron-HI Epoxy P
200-Lug/Dead End C No Body X
36"-Series 200 Flanged D * A536
205-Wafer F
205-Lug G
205-Lug/Dead End H
4. Pressure Code 8. Seat/Liner Code
225-Wafer J 200 PSI 0 Buna 1
225-Lug K
232 PSI (16 Bar) 1 Abrasion Resistant Buna 2
225-Lug/Dead End L
75 PSI 3 Black Neoprene 3
225-Lug /ANSI 300 Bolt Pattern M
285 PSI 5 EPDM 5
255-Lug/Dead End /ANSI 300 N
150 PSI 6 Low Temp Viton 6
400 P
125 PSI (For PTFE Seats) 8 Hypalon 7
800 R
For ATC: PTFE/Buna L
200-Wafer, Euro T
200 PSI Shut-off A High Temp Viton P
• 2"-12", Universal
75 PSI Shut-off B EPDM Food Grade V
• 14"-30", PN16
285 PSI Shut-off C No Seat X
• 36"-Flanged, PN16
For Damper: Viton O
200-Lug, Euro U
250 DEG F P White Buna-Food Grade W
• 2"-30", PN16
500 DEG F T Peroxide Cured Buna 8
200-Lug/Dead End, Euro V
Potable Water EPDM D
• 2"-30, PN16
White Buna B
800-Euro W
• 2"-10", Universal
• 12"-16", PN10
200-Wafer, Euro 7 5. Disc Code 9. Actuator Code
• 14"-30", PN10
• 36"-Flanged, PN10 Ductile Iron-ENP 2 Handle (DIT) 2
200-Lug, Euro 8 316 SS 4 Handle/Infinite Adjustment/ 3
• 2"-30", PN10 Ductile Iron-Zinc Paint 5 Lockable (DIT/IOL)
200-Lug/Dead End, Euro 9 Aluminum Bronze 6 Handle/Infinite Adjustment 4
• 2"-30", PN10 Monel 7 (DIT/IO)
200-Wafer S Ductile Iron-Abrasion Resistant E Gear/Handwheel 5
• Silicone Free Ductile Iron-HI Epoxy T Gear/Chainwheel U
200-Lug E Gear W/Balance Stop/Handwheel G
• Silicone Free Buried Service Gear 2" Sq. Nut C
200-Lug/Dead End Q Direct Nut Operator D
• Silicone Free No Operator X
800-Silicone Free Y
6. Shaft Code
416 SS 1
316 SS 4
Monel K500 5
Monel 400 7
17-4 PH 9
CENTER LINE
3201 Walnut Avenue Long Beach, California 90807
310/430-1094 • FAX: 310/490-9546