Documente Academic
Documente Profesional
Documente Cultură
ELF, partner of
www.lubricants.elf.com
A brand from
Welcome to your new vehicle
This driver’s handbook contains the information necessary:
– for you to familiarise yourself with your vehicle, to use it to its best advantage and to benefit fully from the all the functions and
the technical developments it incorporates.
– to ensure that it always gives the best performance by following the simple, but comprehensive advice concerning regular main-
tenance.
– to enable you to deal quickly with minor faults not requiring specialist attention.
It is well worth taking a few minutes to read this handbook to familiarise yourself with the information and guidelines it contains
about the vehicle and its functions and new features. If certain points are still unclear, our Network technicians will be only too
pleased to provide you with any additional information.
To help you, you will find the following symbols:
and These appear in the vehicle and indicate that you should consult the manual for detailed information and/or
limits on operations with respect to your vehicle’s equipment.
The descriptions of the models given in this handbook are based on the technical specifications at the time of writing. This hand-
book covers all items of equipment (both standard and optional) available for these models but whether or not these are
fitted to the vehicle depends on the version, options selected and the country where the vehicle is sold.
This handbook may also contain information about items of equipment to be introduced later in the model year.
Throughout the manual, the “approved Dealer” is your RENAULT Dealer.
Translated from English. Copying or translation, in part or in full, is forbidden unless prior written permission has been obtained from the vehicle manu-
facturer.
0.1
0.2
C O N T E N T S
Sections
Driving ................................................................... 2
Maintenance ......................................................... 4
0.3
0.4
Section 1: Getting to know your vehicle
1.2
RENAULT CARD: general information (2/3)
Integrated key 5
The integrated key is used to lock or
unlock the front left-hand door if the
RENAULT card does not work:
– when the RENAULT card battery is
5 drained, flat battery, etc.
Driver’s responsibility
– use of devices using the same fre- when parking or stopping
quency as the card; the vehicle
6 – vehicle located in a high electromag- Never leave an animal,
netic radiation zone. child or adult who is not self-suffi-
cient alone on your vehicle, even for
Access to key 5 a short time.
Press button 6 and pull on key 5 then They may pose a risk to themselves
release the button. or to others by starting the engine,
RENAULT card operating activating equipment such as the
range Using the key
electric windows or locking the
This varies according to the surroun- Please refer to the information on doors.
dings: when handling the RENAULT “Locking and unlocking the opening el-
Also, in hot and/or sunny weather,
card, it is important to make sure that ements”.
please remember that the tempera-
you do not lock or unlock the doors by Once you have accessed the vehicle ture inside the passenger compart-
inadvertently pressing the buttons. using the integrated key, replace it ment increases very quickly.
in its housing in the RENAULT card,
RISK OF DEATH OR SERIOUS
then insert the RENAULT card into
INJURY.
the card reader to start the vehicle.
1.3
RENAULT CARD: general information (3/3)
Driver’s responsibility
when parking or stopping
the vehicle
Never leave an animal,
child or adult who is not self-suffi-
cient alone on your vehicle, even for
a short time.
They may pose a risk to themselves
or to others by starting the engine,
activating equipment such as the
electric windows or locking the
Replacement: need for an doors.
additional RENAULT Card Also, in hot and/or sunny weather,
If you lose your RENAULT card or please remember that the tempera-
require another, you can obtain one ture inside the passenger compart-
from an authorised dealer. ment increases very quickly.
If a RENAULT card is replaced, it RISK OF DEATH OR SERIOUS
Advice INJURY.
will be necessary to take the vehi-
Avoid leaving the card in hot, cold or cle and all of its RENAULT cards to
humid areas. an approved Dealer to initialise the
Do not keep the RENAULT card in system.
a place where it could be bent or You may use up to four RENAULT
damaged accidentally, such as in a cards per vehicle.
back pocket of a garment.
1.4
REMOTE CONTROL RENAULT CARD: use
Locking the doors and Unlocking/locking the
luggage compartment luggage compartment only
Press the locking button 2. The indi- Press button 4 to unlock/lock the lug-
2 3 cator lights and hazard warning lights gage compartment.
flash twice to indicate that the doors
have locked. If a door or the luggage
1 4
compartment is open or not properly RENAULT card not detected
shut, or if a RENAULT card is still in the alarm
reader, the doors and luggage compart- If you open a door while the engine
ment lock then quickly unlock and the is running and the card is not in the
hazard warning lights and side repeat- reader, the message “KEYCARD NOT
ers do not flash. DETECTED” and a beep will warn you.
The warning disappears when the card
is inserted in the reader again.
1.5
HANDS-FREE RENAULT CARD: use (1/4)
3
4
1
1.6
HANDS-FREE RENAULT CARD: use (2/4)
Driver’s responsibility
when parking or stopping
the vehicle
Never leave an animal,
3 child or adult who is not self-suffi-
1 cient alone on your vehicle, even for
a short time.
They may pose a risk to themselves
or to others by starting the engine,
Locking the vehicle Locking is shown by one short flash,
activating equipment such as the
then one long flash of the hazard
There are three ways to lock the vehi- electric windows or locking the
warning lights and the side repeaters
cle: remotely, using button 3, or using doors.
and a beep.
the RENAULT card. Also, in hot and/or sunny weather,
The beep may be switched off. Please
please remember that the tempera-
Remote locking consult an authorised dealer.
ture inside the passenger compart-
With the RENAULT card on you, and If a door or the tailgate is open or not ment increases very quickly.
doors and tailgate closed, move away properly shut, or a card is in the pas-
RISK OF DEATH OR SERIOUS
from the vehicle: it will lock automati- senger compartment (or the card
INJURY.
cally once you have left zone 1. reader) the vehicle will not lock. In
Note: the distance at which the vehicle this situation, no beep sounds and the
locks depends on the surroundings. hazard warning lights and side repeat-
ers do not flash.
1.7
HANDS-FREE RENAULT CARD: use (3/4)
3
1
Locking using button 3 Note: a RENAULT card must be within Note: the maximum distance at which
With the doors and boot closed, press the vehicle's access zone (zone 1) to the vehicle locks depends on the sur-
button 3 on one of the front door han- be able to lock the vehicle using the roundings.
dles. The vehicle will lock. The indicator button.
lights and hazard warning lights flash NB: the vehicle cannot be locked again
twice to indicate that the doors have for three seconds after unlocking after
locked. pressing button 3.
If a door or the tailgate is open or not Locking using the RENAULT card
properly closed, the vehicle will quickly
lock/unlock. With the doors and luggage compart-
ment closed, press button 5: the vehi- After locking/unlocking the vehicle
cle will lock. using the buttons on the RENAULT
The indicator lights and hazard warning card, "hands-free" locking and un-
lights flash twice to indicate that the locking is deactivated.
doors have locked.
To reactivate the “hands-free” mode:
restart the vehicle.
1.8
HANDS-FREE RENAULT CARD: use (4/4)
“Hands-free” RENAULT card non-
detection alarm
With the engine running, if you open
and close a door and the card is no
longer within range 6, the message
“KEYCARD NOT DETECTED” and a
beep warns you of this. Driver’s responsibility
The warning disappears when the card when parking or stopping
6 is again within range 6. the vehicle
Never leave an animal,
child or adult who is not self-suffi-
cient alone on your vehicle, even for
a short time.
They may pose a risk to themselves
or to others by starting the engine,
Special features
activating equipment such as the
The vehicle will not lock if: electric windows or locking the
– a door or the tailgate is open or not doors.
properly closed; Also, in hot and/or sunny weather,
– a card is still in zone 6 (or in the card please remember that the tempera-
reader) and no other card is in the ture inside the passenger compart-
external detection zone. ment increases very quickly.
RISK OF DEATH OR SERIOUS
INJURY.
1.9
RENAULT CARD: deadlocking
Special note: deadlocking is not pos-
sible if the hazard warning lights or the
side lights are lit.
1 2
1.10
OPENING AND CLOSING THE DOORS (1/2)
4
1 3
Opening the doors from the Rear doors Opening from the inside
outside With the doors unlocked, pull handle 3. Pull handle 4.
Front doors
With the doors unlocked, pull handle 1.
As a safety precaution,
the doors should only be
opened or closed when the
vehicle is stationary.
1.11
OPENING AND CLOSING THE DOORS (2/2)
Lights-on reminder buzzer
If you have switched off the ignition
and left the lights switched on, a re-
minder buzzer will sound when a door
is opened.
1.12
LOCKING, UNLOCKING THE DOORS (1/2)
Locking/Unlocking the doors
from the outside
This is done using the RENAULT Card;
see the “RENAULT Card” information in 2
Section 1.
In certain cases, the RENAULT card
may not work: 1
– if the RENAULT card battery is weak,
flat, etc.
– if equipment operating on the same
frequency as the card (mobile
phones, etc.) is used;
– vehicle located in a high electromag-
netic radiation zone.
Using the key integrated in Locking the doors manually
It is then possible:
the RENAULT card Turn screw 2 with the door open (using
– to use the key integrated into the the end of the key) and close the door.
Insert key 1 into the lock in the driver’s
card to unlock the front left-hand
door and lock or unlock. This means that the doors are then
door;
locked from the outside.
– to lock each of the doors manually;
The doors may then only be opened
– to use the interior door locking/un- from the inside or by using the key in
locking control (refer to the following the front left-hand door.
pages).
1.13
LOCKING, UNLOCKING THE DOORS (2/2)
Locking the doors without Door and tailgate status
3 the RENAULT card indicator
For example, in the event of a dis- With the ignition on, the warning light
charged battery or the RENAULT card integrated in switch 3 informs you of the
temporarily not working, etc. locking status of the opening elements:
With the engine switched off and – indicator light on, the doors and tail-
an opening element (door or boot) gate are locked,
open, press and hold switch 3 for more – indicator light off, the doors and tail-
than five seconds. gate are unlocked.
When the door is closed, all the doors When you lock the doors, the indicator
and the tailgate will be locked. light remains lit and then goes out.
Unlocking the vehicle from the outside
is only possible with the RENAULT card
in the vehicle's access zone or using
Interior locking/unlocking the key integrated in the RENAULT
door control card.
Switch 3 controls the doors, boot and,
depending on the vehicle, the fuel filler Never leave your vehicle
flap simultaneously. with the RENAULT card
If a door or the tailgate is open or not inside.
closed properly, the doors and tailgate
lock/unlock quickly.
If you need to transport objects with the
boot open, the other opening elements Driver’s responsibility
After locking/unlocking the vehicle
can still be locked: with the engine using the buttons on the RENAULT If you decide to keep the
stopped, press switch 3 for more than card, "hands-free" locking and un- doors locked when you are
five seconds to lock the other opening locking is deactivated. driving, remember that it
elements. may be more difficult for those as-
To reactivate the “hands-free” mode:
sisting you to gain access to the
restart the vehicle.
passenger compartment in the
event of an emergency.
1.14
RENAULT ANTI-INTRUDER DEVICE (RAID)
Activating/deactivating the
1 function
With the engine running, press
button 1 for approximately five seconds
until you hear a beep.
Operating faults
If you experience an operating fault
(no automatic locking, the indicator
light incorporated in button 1 does not
light up when trying to lock the open-
ing elements, etc.), firstly check that the
opening elements are properly closed.
If they are properly closed, contact an
Operating principle authorised dealer.
After the vehicle is started, the system
automatically locks the doors when
you are driving at approximately 6 mph
(10 km/h) and over.
The door can be unlocked:
– by pressing the door unlocking
button 1.
– by opening a front door (vehicle sta-
tionary). Driver’s responsibility
1.15
FRONT HEADRESTS
To raise the headrest
Raise the headrest to its highest po-
sition (tilt the seatback backwards if
A necessary). Press button 1 and lift the
2
headrest to release it.
1
To refit the headrest
Insert the headrest rods into the holes
(tilt the seatback backwards if neces-
sary). Lower the headrest until it locks
and press button 1 to adjust to the de-
sired height. Check that each rod 2 on
the seatback is securely locked.
1.16
FRONT SEATS (1/3)
2
3
4
1
To move the seat forwards or To raise or lower the seat To tilt the seatback
backwards base Turn control knob 4 and tilt the seat-
Lift handle 1 to unlock. Release the Move lever 2 as many times as neces- back to the desired position.
handle once the seat is in the correct sary upwards or downwards.
position and ensure that the seat is
locked.
Heated seats
With the ignition switched on, press
For safety reasons, carry switch 3 on the required seat. The indi-
out any adjustments when cator light in the switch lights up.
the vehicle is not being The system, which has a thermostat,
driven. regulates the heating and deactivates it
Nothing should be placed on the if necessary.
We would advise you not
floor (area in front of driver) as such to recline the seatbacks too
objects may slide under the pedal far to ensure that the effec-
during braking manoeuvres, thus tiveness of the seat belts is
obstructing its use. not reduced.
1.17
FRONT SEATS (2/3)
To reposition the passenger seat
For your safety, attach any
Make sure that nothing prevents the transported objects when
5 seat from moving. the seat is in the table po-
– Activate control 5 to unlock the seat- sition.
back;
– Lift the seat back;
– Make sure the seat is correctly
locked in position.
1.18
FRONT SEATS (3/3)
1.19
SEAT BELTS (1/4)
Always wear your seat belt when trav- Before starting, first adjust your driv-
elling in your vehicle. You must also ing position, then ask all occupants
comply with the legislation of the par- to adjust their seat belts to ensure
ticular country you are in. optimum protection.
1.20
SEAT BELTS (2/4)
Front seat belt reminder
ß warning light
This lights up on the central display
when the engine is started then, if the
driver’s or front passenger’s seat belt 6
(if this seat is occupied) is not fastened
and the vehicle has reached approxi-
1 mately 12 mph (20 km/h), it flashes and
a bleep sounds for around 2 minutes.
Note: an object placed on the passen-
ger seat base may activate the warning
3 light in some cases.
4 Rear seat belt reminder (depending
5 5 on vehicle)
Locking
the ß warning light on the cen-
tral display lights up accompanied by a Adjusting the height of the
Unwind the belt slowly and smoothly message on the instrument panel indi- front seat belts
and ensure that buckle 3 locks into cating the number of seat belts buck- Press button 6 to adjust the seat belt
catch 5 (check that it is locked by pull- led for approximately 30 seconds each height so that shoulder strap 1 is worn
ing on buckle 3). time: as shown previously. Press button 6
– the vehicle is started; and raise or lower the seat belt. Make
If the belt jams, allow it to return slightly
– a door is opened; sure that the seat belt is locked in posi-
before attempting to unwind it again.
– a rear seat belt is fastened or unfas- tion correctly after you have adjusted it.
If your seat belt is completely jammed, tened.
pull slowly, but firmly, so that just over
Check that the rear passengers are Unlocking
3 cm unwinds. Allow it to return slightly
wearing seat belts and that the number
before attempting to unwind it again. Press button 4 and the seat belt will be
of seat belt shown as fastened corre-
If there is still a problem, contact an ap- sponds to the number of rear bench rewound by the inertia reel. Guide the
proved dealer. seat places occupied. belt.
1.21
SEAT BELTS (3/4)
7 9 10
12
11
Rear side seat belts 7 Rear centre seat belt Fasten sliding buckle 10 into the corre-
sponding red catch 12.
The belts are locked, unlocked and Unwind belt 9 slowly from its housing,
adjusted in the same way as the front then fasten buckle 8 into the corre-
belts. sponding black catch 11.
1.22
SEAT BELTS (4/4)
The following information applies to the vehicle’s front and rear seat belts.
– No modification may be made to the component parts of the originally fitted restraint system: seat belts, seats and
their mountings. For special operations (e.g. fitting child seats), contact an authorised dealer.
– Do not use devices which allow any slack in the belts (e.g. clothes pegs, clips, etc.): a seat belt which is worn too
loosely may cause injury in the event of an accident.
– Never wear the shoulder strap under your arm or behind your back.
– Never use the same belt for more than one person and never hold a baby or child on your lap with your seat belt around
them.
– The belt should never be twisted.
– Following an accident, have the seat belts checked and replaced if necessary. Always replace your seat belts as soon as
they show any signs of wear.
– When the rear bench seat is being put back, make sure that the seat belts and buckles are correctly positioned so that they
can be used properly.
– Make sure that the buckle is inserted into the appropriate catch.
– Ensure that no objects are placed in the area around the seat belt catch as they could prevent it from being properly se-
cured.
– Make sure the seat belt catch is properly positioned (it should not be hidden away, crushed or flattened by people or ob-
jects).
1.23
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (1/4)
Depending on the vehicle, they will con-
sist of: – Have the entire restraint
system checked following
– front seat belt inertia reel preten- an accident.
sioners;
– No operation whatso-
– chest-level load limiters; ever is permitted on any part of
– air bags for driver and front pas- the system (pretensioners, air
senger. bags, computers, wiring) and the
system components must not
These systems are designed to act in- be reused on any other vehicle,
dependently or together when the vehi- even if identical.
cle is subjected to a frontal impact.
– To avoid incorrect triggering of
Depending on the severity of the the system which may cause
impact, the system can trigger: injury, only qualified personnel
1
– seat belt locking; from an approved Dealer may
work on the pretensioner and air
– the seat belt inertia reel pretensioner Pretensioners bag system.
(which engages to correct seat belt
slack); The pretensioners hold the seat belt – The electric trigger system may
against the body, holding the occupant only be tested by a specially
– airbags. more securely against the seat, thus in- trained technician using special
creasing the seat belt’s efficiency. equipment.
With the ignition on, following a signif- – When the vehicle is scrapped,
icant frontal impact and depending on contact an approved Dealer for
the severity of the impact, the system disposal of the pretensioner and
may trigger the seat belt inertia reel air bag gas generators.
pretensioner 1, which instantly retracts
the seat belt.
1.24
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (2/4)
Load limiter Airbags for driver and front
Above a certain severity of impact, this passenger
mechanism is used to limit the force of Fitted to the driver and passenger side.
the belt against the body so that it is at A
an acceptable level. The presence of this equipment is in-
dicated by the word “Air bag” on the
steering wheel and dashboard (air bag
zone A) and, depending on the vehicle,
a symbol on the lower section of the
windscreen.
Each air bag system consists of:
– an air bag and gas generator fitted
on the steering wheel for the driver
and in the dashboard for the front
passenger;
– an electronic unit for system monitor-
ing which controls the gas generator
electrical trigger system;
1.25
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (3/4)
1.26
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (4/4)
All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent
the risk of serious injuries caused by items which may be dislodged when the air bag inflates.
1.27
METHODS OF RESTRAINT IN ADDITION TO THE REAR SIDE SEAT BELTS
Force limiter
Above a certain severity of impact, this
mechanism is used to limit the force of
the belt against the body so that it is at
an acceptable level.
1.28
SIDE PROTECTION DEVICES
Side Airbags
This airbag may be fitted to each of the
front seats and is activated at the sides
of the seats (door side) to protect the
occupants in the event of a severe side
impact.
1.29
ADDITIONAL METHODS OF RESTRAINT
All of the warnings below are given so that the airbag is not obstructed in any way when it is inflated and also to prevent
the risk of serious injuries caused by items which may be dislodged when it inflates.
The airbag is designed to complement the action of the seat belt. Both the air bags and seat belts are integral parts of
the same protection system. It is therefore essential to wear seat belts at all times. If seat belts are not worn, the oc-
cupants are exposed to the risk of serious injury in the event of an accident. It may also increase the risk of minor su-
perficial injuries occurring when the airbag is deployed, although such minor injuries are always possible with air bags.
If the vehicle should overturn or in the event of a rear impact, however severe, the pretensioners and airbags are not always
triggered. Impacts to the underside of the vehicle, e.g. from pavements, potholes or stones, can all trigger these systems.
– No work or modification whatsoever may be carried out on any part of the airbag system (airbags, pretensioners, computer,
wiring harness, etc.), except by qualified Network personnel.
– To ensure that the system is in good working order and to avoid accidental triggering of the system which may cause injury,
only qualified Network personnel may work on the airbag system.
– As a safety precaution, have the airbag system checked if your vehicle has been involved in an accident, or is stolen or
broken into.
– When selling or lending the vehicle, inform the user of these points and hand over this handbook with the vehicle.
– When scrapping your vehicle, contact your approved Dealer for disposal of the gas generator(s).
1.30
CHILD SAFETY: General information (1/2)
Carrying children
Please ensure that you comply with the
legislation of your country.
Children, and adults, must be correctly
seated and strapped in for all journeys.
The children being carried in your vehi-
cle are your responsibility.
A child is not a miniature adult. Children Driver’s responsibility
are at risk of specific injuries as their when parking or stopping
muscles and bones have not yet fin- the vehicle
ished growing. The seat belt alone Never leave an animal,
would not provide suitable protection. child or adult who is not self-suffi-
Use an approved child seat and ensure cient alone on your vehicle, even for
you use it correctly. a short time.
They may pose a risk to themselves
or to others by starting the engine,
A collision at 30 mph activating equipment such as the
(50 km/h) is the same as fall- electric windows or by locking the
ing a distance of 10 metres. doors.
Transporting a child without Also, in hot and/or sunny weather,
a restraint is the equivalent of allow- please remember that the tempera-
ing him or her to play on a fourth- ture inside the passenger compart-
floor balcony without railings. ment increases very quickly.
Never travel with a child held in your
arms. In the event of an accident, RISK OF DEATH OR SERIOUS
you will not be able to keep hold of INJURY.
To prevent the doors being the child, even if you yourself are
opened, use the “Child wearing a seat belt.
safety” device (refer to the If your vehicle has been involved in
information on “Opening a road accident, replace the child
and closing the doors” in Section 1). seat and have the seat belts and
ISOFIX anchorage points checked.
1.31
CHILD SAFETY: General information (2/2)
Using a child seat
Set a good example by always fas-
The level of protection offered by the
tening your seat belt and teaching
child seat depends on its ability to re-
your child:
strain your child and on its installation.
– to strap themselves in correctly;
Incorrect installation compromises the
– to always get in and out of the car
protection it offers the child in the event
at the kerb, away from busy traf-
of harsh braking or an impact.
fic.
Before purchasing a child seat, check
Do not use a second-hand child
that it complies with the regulations for
seat or one without an instruction
the country you are in and that it can
manual.
be fitted in your vehicle. Consult an ap-
proved dealer to find out which seats Check that there are no objects in
are recommended for your vehicle. the vicinity of the child seat which
could impede its operation.
Before fitting a child seat, read the
manual and respect its instructions. If
you experience any difficulties during Never leave a child unat-
installation, contact the manufacturer tended in the vehicle.
of the equipment. Keep the instructions
Check that your child is
with the seat.
always strapped in and that
the belt or safety harness used is
correctly set and adjusted. Avoid
wearing bulky clothing which could
cause the belts to slacken.
Never let your child put their head or
arms out of the window.
Check that the child is in the correct
position for the entire journey, espe-
cially if asleep.
1.32
CHILD SAFETY: choosing a child seat
1.33
CHILD SAFETY: choosing a child/baby seat mounting (1/2)
There are two ways of attaching child Attachment using the ISOFIX
seats: via the seat belt or using the Before using an ISOFIX system
ISOFIX system. child seat that you pur-
chased for another vehicle, Authorised ISOFIX child seats are ap-
Attachment via the seat belt check that its installation is proved in accordance with regulation
The seat belt must be adjusted to authorised. Consult the list of ve- ECE-R44 in one of the three following
ensure that it is effective in the event of hicles which can be fitted with the cases:
harsh braking or an impact. seat from the equipment manufac- – ISOFIXuniversal 3-point forward-fac-
Ensure that the strap paths indicated turer. ing seat;
by the child seat manufacturer are re- – ISOFIXsemi-universal 2-point seat;
spected. – specific.
Always check that the seat belt is cor- For the latter two, check that your child
rectly fastened by pulling it up, then seat can be installed by consulting the
pulling it out fully whilst pressing on the list of compatible vehicles.
child seat. Attach the child seat with the ISOFIX
Check that the seat is correctly held by locks, if these are provided. The ISOFIX
moving it from side to side and back system allows quick, easy, safe fitting.
to front: the seat should remain firmly
fixed. The seat belt must never The ISOFIX system consists of 2 rings
Check that the child seat has not been be twisted or the tension and, in some cases, a third ring.
installed at an angle and that it is not relieved. Never pass the
resting against a window. shoulder strap under the
arm or behind the back.
Check that the seat belt has not
been damaged by sharp edges.
If the seat belt does not operate nor-
mally, it will not protect the child.
Do not use the child seat
Consult an approved dealer. Do not
if it may unfasten the seat
use this seat until the seat belt has
belt restraining it: the base
been repaired. No modifications may be
of the seat must not rest on
the buckle and/or catch of the seat made to the component
belt. parts of the restraint system
(seat belts, ISOFIX and
seats and their mountings) originally
fitted.
1.34
CHILD SAFETY: choosing a child/baby seat mounting (2/2)
Pull the belt 2 so that the back of the
child seat comes into contact with the
vehicle seatback.
A B
2
3
1 4
The two rings 1 are located between Rear seats
the seatback and the seat base, they The 2 belt should be positioned be-
are marked (depending on the vehicle) tween the seatback and the rear parcel
by A or B. shelf. To do this, remove the rear parcel
The third ring 4 is used to attach the shelf (refer to the information on the
upper strap on some child seats. “Rear parcel shelf” in Section 3). Attach
the hook to one of the 4 rings, identi-
fied using the symbol. Depending
on the vehicle, unclip cover 3 from the
mobile floor to access the ring.
Check that the seatback
The ISOFIX anchorage points have been exclusively designed for child of the forward-facing child
seats with the ISOFIX system. Never fit a different type of child seat, seat seat is in contact with the
belt or other objects to these anchorage points. back of the vehicle seat.
Check that nothing is obstructing the anchorage points. In this case, the child seat may not
If your vehicle has been involved in a road accident, have the ISOFIX anchorage always rest on the base of the vehi-
points checked and replace your child seat. cle seat.
1.35
CHILD SAFETY: fitting a child seat, general information (1/2)
Some seats are not suitable for fitting In the front seat After installing the child seat, when this
child seats. The diagram on the follow- The laws concerning children travel- is possible, you can move the vehi-
ing page shows you how to attach a ling in the front passenger seat differ in cle seat forward if necessary (so as to
child seat. every country. Consult the legislation in leave enough space in the rear seats
The types of child seat indicated may force and follow the indications on the for passengers or other child seats). In
not be available. Before using a differ- diagram on the following page. the case of a rear-facing child seat, do
ent child seat, check with the manufac- not let it touch the dashboard or move it
Before fitting a child seat in this seat (if to the furthest forward position.
turer that it can be fitted. authorised):
Do not change other settings after in-
– lower the seat belt as far as possible; stalling the child seat.
– move the seat as far back as possi-
ble;
Ensure that the child seat
or the child’s feet do not – gently tilt the seatback away from
prevent the front seat from vertical (approximately 25°);
locking correctly. Refer to – on equipped vehicles, raise the seat
the information on the “Front seat” base as far as possible.
in Section 1.
Check that when installing the child In all situations, reinsert the headrest to
seat in the vehicle it is not at risk of its full extent so that it does not interfere
coming loose from its base. with the child seat (see the information
If you have to remove the headrest, on “Front headrests” in Section 1);
check that it is correctly stored so
that it does not come loose under RISK OF DEATH OR
harsh braking or impact. SERIOUS INJURY: Before
Always attach the child seat to the installing a child seat on the
vehicle even if it is not in use so that front passenger seat, check
it does not come loose under harsh that the airbag has been deacti-
braking or impact. vated (please refer to “Child safety:
front passenger airbag deactivation
and activation” in Section 1).
1.36
CHILD SAFETY: fitting a child seat, general information (2/2)
In the rear side seat Rear centre seat
A carrycot can be installed across the Check that the belt is suitable for secu-
vehicle and will take up at least two ring your child seat. Consult an appro-
seats. Position the child with his or her ved dealer.
feet nearest the door.
Move the front seat as far forward as
possible to install a rear-facing child
seat, then move back the seat in front
as far as it will go, although without al-
lowing it to come into contact with the
child seat.
For the safety of the child in the for-
ward-facing position:
– Move the relevant seat backwards
as far as possible;
– move the seat in front of the child
forwards, and set the position of the
seatback to avoid contact between
the seat and the child’s legs.
Always remove the headrest from the A child seat with floor sup-
rear seat used for the child seat (see ports must never be ins-
“Rear headrests” in Section 3). If nec- talled on the rear centre
essary, position the rear seat as far seat. RISK OF DEATH OR
back as possible. This must be done SERIOUS INJURY.
before fitting the child seat. Check that
the child seat is resting against the
back of the vehicle seat.
1.37
CHILD SEATS: attachment by seat belt (1/5)
The table below summarises the information already shown in the diagram on the following pages, to ensure the appli-
cable regulations are respected.
Front passenger
Type of child seat Weight of the child Rear side seats (6) Rear centre seat
seat (1) (2)
Carrycot fitted
across the vehicle < 10 kg X U (3) X
Group 0
Rear-facing shell
seat < 10 kg and < 13 kg U U (4) U (4)
Groups 0 or 0 +
Shell seat/rear-facing
seat < 13 kg and 9 to 18 kg U U (4) U (4)
Groups 0+ and 1
Forward-facing seat
9 to 18 kg X U (5) U (5)
Group 1
(1) RISK OF DEATH OR SERIOUS INJURY: Before installing a child seat on the front passenger seat, check that
the airbag has been deactivated (please refer to “Child safety: front passenger airbag deactivation and activation” in
Section 1).
1.38
CHILD SEATS: attachment by seat belt (2/5)
X = Seat not suitable for fitting child seats of this type.
U = Seat which allows a child seat with “Universal” approval to be installed using a seat belt; check that it can be fitted.
(2) Raise the seat to the maximum and position it as far back as possible, tilting the seatback slightly (approximately 25°).
(3) A carrycot can be installed across the vehicle and will take up at least two seats. Position the child with his or her feet nearest
the door.
(4) Move the front seat as far forward as possible to install a rear-facing child seat, then move back the seat in front as far as it will
go, although without allowing it to come into contact with the child seat.
(5) Forward-facing child seat; position the seatback of the child seat in contact with the seatback of the vehicle seat. Adjust the
headrest, or remove it if necessary. Do not push the seat in front of the child more than halfway back on its runners and do not
recline the seatback more than 25°.
(6) Make sure that the child seat or the child’s feet do not prevent the front seat from locking correctly. Refer to the information on
the “Front seat” in Section 1.
1.39
CHILD SEATS: attachment by seat belt (3/5)
Visual installation of five door and estate versions
³ Check the status of the airbag
before fitting a child seat or allowing a
passenger to use the seat.
Seat not suitable for fitting
² child seats.
Child seat attached using the belt
RISK OF DEATH OR
SERIOUS INJURY: Before
installing a child seat on the
front passenger seat, check Using a child safety system
that the airbag has been deacti- which is not approved for
vated (please refer to “Child safety: this vehicle will not correctly
front passenger airbag deactivation protect the baby or child.
and activation” in Section 1). They risk serious or even fatal injury.
1.40
CHILD SEATS: attachment by seat belt (4/5)
View of the utility version installation
³ Check the status of the airbag
before fitting a child seat or allowing a
passenger to use the seat.
Seat not suitable for fitting
² child seats.
Child seat attached using the belt
RISK OF DEATH OR
SERIOUS INJURY: Before
installing a child seat on the
front passenger seat, check Using a child safety system
that the airbag has been deacti- which is not approved for
vated (please refer to “Child safety: this vehicle will not correctly
front passenger airbag deactivation protect the baby or child.
and activation” in Section 1). They risk serious or even fatal injury.
1.41
CHILD SEATS: attachment by seat belt (5/5)
The table below summarises the information already shown on the diagram on U = Seat which allows a child seat with
the previous page, to ensure the regulations in force are respected. “Universal” approval to be installed
using a seat belt; check that it can
be fitted.
Utility version
(2) Raise the seat to the maximum and
position it as far back as possible,
tilting the seatback slightly (approxi-
Front passenger mately 25°).
Type of child seat Weight of the child
seat (1) (2)
Rear-facing shell
seat < 10 kg and < 13 kg U
Groups 0 or 0 +
Shell seat/rear-facing
seat < 13 kg and 9 to 18 kg U
Groups 0+ and 1
Forward-facing seat
9 to 18 kg U
Group 1
Booster seat
15 to 25 kg and 22 to 36 kg U
Groups 2 and 3
1.42
CHILD SEATS: attachment using the ISOFIX system (1/5)
Visual installation of five door and estate versions Child seat fitted using the ISOFIX
mounting
ü Seat which allows a ISOFIX child
seat to be attached.
1.43
CHILD SEATS: attachment using the ISOFIX system (2/5)
The table below summarises the information already shown in the diagram on the following pages, to ensure the appli-
cable regulations are respected.
Carrycot fitted
across the vehicle < 10 kg F, G X IL (1) X
Group 0
Rear-facing shell
< 10 kg and
seat E X IL (2) X
< 13 kg
Groups 0 or 0 +
Shell seat/rear-facing
< 13 kg and 9 to
seat C, D X IL (2) X
18 kg
Groups 0+ and 1
Forward-facing seat
9 to 18 kg A, B, B1 X IUF - IL (3) X
Group 1
1.44
CHILD SEATS: attachment using the ISOFIX system (3/5)
X = Seat not suitable for fitting child seats ISOFIX.
IUF/IL = On equipped vehicles, seat which allows an approved “Universal/semi-universal” or “vehicle specific” child seat to be at-
tached using the ISOFIX system; check that it can be fitted.
(1) A carrycot can be installed across the vehicle and will take up at least two seats. Position the child with his or her feet nearest
the door.
(2) Move the front seat as far forward as possible to install a rear-facing child seat, then move back the seat in front as far as it will
go, although without allowing it to come into contact with the child seat.
(3) Forward-facing child seat; position the seatback of the child seat in contact with the seatback of the vehicle seat. Adjust the
headrest, or remove it if necessary. Do not push the seat in front of the child more than halfway back on its runners and do not
recline the seatback more than 25°.
(4) Make sure that the child seat or the child’s feet do not prevent the front seat from locking correctly. Refer to the information on
the “Front seat” in Section 1.
1.45
CHILD SEATS: attachment using the ISOFIX system (4/5)
View of the utility version installation
1.46
CHILD SEATS: attachment using the ISOFIX system (5/5)
The table below summarises the information already shown on the diagram on the previous page, to ensure the regula-
tions in force are respected.
Utility version
Type of child seat Weight of the child Seat size ISOFIX Front passenger seat
Forward-facing seat
9 to 18 kg A, B, B1 X
Group 1
Booster seat
15 to 25 kg and 22 to 36 kg X
Groups 2 and 3
1.47
CHILD SAFETY: deactivating, activating the front passenger air bag (1/3)
DANGER
1 Since operation of the front
passenger airbag is not
compatible with the position
of a rear-facing child seat, NEVER
2 fit a restraint system for a rear-fac-
ing child in a seat protected by an
ACTIVATED front AIRBAG. This
can cause the CHILD’S DEATH or
SERIOUS INJURY.
Deactivating the front To deactivate the airbags: with the
passenger airbags vehicle stopped and the ignition off,
(on equipped vehicles) push and turn lock 1 to the OFF posi-
tion.
You must deactivate the passenger
airbag before fitting a child seat on the With the ignition on, you must check
front passenger seat. that the warning light¹ on the dis-
play 2 is lit up and, depending on the
The passenger air bag must
only be deactivated or acti-
vehicle, that the message “airbag pas- vated with the ignition off.
senger deactivated” is displayed. If it is interfered with when
This light remains permanently lit to the vehicle is being driven, indicator
let you know that you can fit a child
seat.
lights
on.
å and © will come
1.48
CHILD SAFETY: deactivating, activating the front passenger air bag (2/3)
A
3
1.49
CHILD SAFETY: deactivating, activating the front passenger air bag (3/3)
Operating faults
It is forbidden to fit a rear-facing child
seat to the front passenger seat if the
airbags activation/deactivation system
is faulty.
Allowing any other passenger to sit in
1 that seat is not recommended.
Contact your approved dealer as soon
as possible.
2
1.50
STEERING WHEEL/POWER-ASSISTED STEERING
Power Assisted Steering
Never drive with an inadequately
charged battery.
1.51
DRIVING POSITION: LEFT-HAND DRIVE (1/2)
1 2 3 4 5 6 7 8 9 10 11 12 13 14
27
26 25 24 23 17 16 15
22 18
21
19
20
1.52
DRIVING POSITION: LEFT-HAND DRIVE (2/2)
The equipment fitted, described below, DEPENDS ON THE VERSION AND COUNTRY.
1.53
DRIVING POSITION: RIGHT-HAND DRIVE (1/2)
1 2 3 4 5 6 7 8 9 10 11 12 13 14
15
26 25 24 23 17 16
22
27
21
18
20
19
1.54
DRIVING POSITION: RIGHT-HAND DRIVE (2/2)
The equipment fitted, described below, DEPENDS ON THE VERSION AND COUNTRY.
1 Side air vent. 11 Driver Airbag and horn location. 17 Control for adjusting steering
wheel height and reach.
2 Passenger Airbag location. 12 Multimedia system voice control
button. 18 Main switch for:
3 Heating or air conditioning con- – speed limiter;
trols. 13 Stalk: – cruise control.
– windscreen and rear screen
4 Multimedia touch-screen. wash/wipe; 19 Activation/deactivation control for
– trip computer and warning ECO mode ECO.
5 Windscreen demister outlet. system information readout.
20 Handbrake.
6 Hazard warning lights switch. 14 Side air vent.
21 Gear lever.
7 Door electric locking switch. 15 Controls for:
– electric headlight beam adjust- 22 Cigarette lighter/accessories
8 Centre air vents. ment, socket.
1.55
WARNING LIGHTS (1/5)
The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.
1.56
WARNING LIGHTS (2/5)
The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.
1.57
WARNING LIGHTS (3/5)
The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.
1.58
WARNING LIGHTS (4/5)
The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.
1.59
WARNING LIGHTS (5/5)
The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.
1.60
DISPLAYS AND INDICATORS (1/2)
5
3
6
2
1.61
DISPLAYS AND INDICATORS (2/2)
5 6 7
9
8
1.62
ON-BOARD COMPUTER: general information (1/2)
f) distance travelled;
1 g) average speed;
h) distance before service;
– service counter;
– oil change counter;
2 i) Reset the tyre pressure
j) Cruise control and speed limiter pro-
grammed speed
k) Clock and temperature
l) Trip log, operating faults and infor-
mation message readout
1.63
ON-BOARD COMPUTER: general information (2/2)
Interpreting some of the Automatic resetting of the
values displayed after journey parameters
resetting Resetting occurs automatically when
The values showing average fuel con- the maximum value of any of the pa-
2 sumption, range and average speed rameters is exceeded.
will become more stable and reliable
the further you travel after pressing the
reset button.
For the first few miles after pressing
the reset key you will notice that the
range increases as you travel. This
range takes into account the average
3 fuel consumption since the last time the
reset button was pressed. Therefore,
the average fuel consumption may de-
Resetting the trip mileage crease when:
With “trip mileage recorder” selected on – the vehicle stops accelerating;
the display, press button 2 or 3 until the
mileage recorder resets to zero. – the engine reaches its operating
temperature (if the engine was cold
when the reset key was pressed);
Resetting the journey – when driving from an urban area
parameters (reset button) onto the open road.
With one of the trip parameters selected
as the display, press and hold button 2
or 3 until the display resets.
1.64
TRIP COMPUTER: trip settings (1/5)
The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.
101778 km
112.4 km a) Total mileage and trip mileage recorder.
FUEL USED
b) Journey parameters.
8L Fuel used.
Fuel consumed since the last reset.
AVERAGE
c) Average fuel consumption since the last reset.
5.8 L/100 The value is displayed after having travelled at least 400 metres since the last
reset.
CURRENT
7.4 L/100 d) Current fuel consumption.
This value is displayed after a speed of approximately 20 mph (30 km/h) is reached.
1.65
TRIP COMPUTER: trip settings (2/5)
The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.
RANGE
541 km e) Estimated range with remaining fuel.
The value is displayed after driving 400 metres.
DISTANCE
522 km f) Distance travelled since last reset.
AVERAGE
123.4 km/H g) Average speed since the last reset.
The value is displayed after driving 400 metres.
1.66
TRIP COMPUTER: trip settings (3/5)
The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.
Examples of selections
On-board computer with mileage- Interpreting the display selected
before-service message
h) Mileage before service or oil change.
Reset: to reset the distance before service, press and hold button 2 or 3 for approximately 10 seconds until the display shows
the mileage permanently.
NB: if a service is performed without changing the engine oil, only the mileage before the next service should be reset. In the
event of an oil change, both the distance before the next service and the next oil change should be reset.
1.67
TRIP COMPUTER: trip settings (4/5)
The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.
Examples of selections
On-board computer with distance before Interpreting the display selected
next service message (cntd.)
h) Mileage before service or oil change.
Mileage before service
SERVICE OIL CHANGE IN With the ignition switched on and the engine not running,
INTERVALS 30 000 Kms / 24 MO and the selected display is “Mileage before service”, press one
of buttons 2 or 3 for about 5 seconds to display the mileage
before a service, then briefly press one of buttons 2 or 3 to view
the range (distance or time remaining before the next service).
SERVICE DUE IN When the distance value approaches its limit, there are several
possible scenarios:
300 Kms / 24 DAYS
– distance/time remaining less than 900 miles (1,500 km) or
one month: the message “Service due in” is displayed ac-
companied by the nearest term (distance or time);
– range equal to 0 km/miles or service date reached: the
SERVICE REQUIRED message “service vehicle” is displayed accompanied by the
© warning light.
The vehicle requires an oil change as soon as possible.
Depending on the vehicle, the mileage before an oil change varies according to the driving style (frequent driving at low speed,
door-to-door journeys, extensive use at idling speed, towing a trailer, etc.). The distance remaining until the next oil change can
therefore decrease more quickly in some cases than the actual distance travelled.
Reset: to reset the distance before service, press and hold button 2 or 3 for approximately 10 seconds until the display shows
the mileage permanently.
NB: if a service is performed without changing the engine oil, only the mileage before the next service should be reset. In the
event of an oil change, both the distance before the next service and the next oil change should be reset.
1.68
TRIP COMPUTER: trip settings (5/5)
The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.
SPEED LIMITER
90 km/H
j) Cruise control and speed limiter programmed speed.
Refer to the information in “Cruise control” and “Speed limiter” in Section 2.
CRUISE CONTROL
90 km/H
l) Trip log.
NO MESSAGE Successive display:
MEMORISED
– information messages (passenger airbag OFF etc.);
– operating fault messages (check the injection system, etc.).
1.69
TRIP COMPUTER AND WARNING SYSTEM: information messages
These can help in the vehicle starting phase, or give information about a selection or a driving status.
Examples of information messages are given in the following pages.
« PARKING BRAKE ON » Indicates that the parking brake has been applied.
« PLEASE REMOVE
Request to remove the RENAULT card from the reader when you leave the vehicle.
KEYCARD »
« TRACTION
Indicates that you have deactivated the traction control function.
CONTROL OFF »
« TURN STEERINGWHEEL Turn the steering wheel slightly whilst pressing the vehicle start button to unlock the steering
+ START » column.
« STEERING WHEEL
Indicates that the steering column has not been locked.
NOT LOCKED »
1.70
TRIP COMPUTER AND WARNING SYSTEM: operating fault messages
These appear with the © warning light and mean that you should drive very carefully to an authorised dealer as
soon as possible. If you fail to follow this recommendation, you risk damaging your vehicle.
They disappear when the display selection key is pressed or after several seconds and are stored in the computer log. The
© warning light stays on. Examples of operating fault messages are given in the following pages.
« CLEAN DIESEL FILTER » Indicates the presence of water in the diesel filter; contact an approved Dealer
as soon as possible.
« CHECK VEHICLE » Indicates a fault in one of the pedal sensors, battery management system or oil
level sensor.
« CHECK AIRBAG » Indicates a fault in the restraint system in addition to the seat belts. In the event
of an accident, it is possible that they may not be triggered.
« CHECK ANTI-POLLUTION SYSTEM » Indicates a fault in the vehicle’s particle filter system.
1.71
TRIP COMPUTER AND WARNING SYSTEM: warning message
These appear with the ® warning light and require you to stop immediately, for your own safety, as soon as traf-
fic conditions allow. Stop your engine and do not restart it. Contact an approved Dealer.
Examples of warning messages are given in the following pages. Note: the messages appear on the display either individually
or alternately (when there are several messages to be displayed), and may be accompanied by a warning light and/or a beep.
« ENGINE FAILURE HAZARD » Indicates an injection fault, the vehicle’s engine has overheated or there is a
serious engine fault.
« BATTERY CHARGING FAULT » Indicates a fault in the vehicle battery charging circuit (alternator etc.).
1.72
CLOCK AND EXTERIOR TEMPERATURE (1/2)
A
2
9°C 12:00
1.73
CLOCK AND EXTERIOR TEMPERATURE (2/2)
External temperature
indicator
Special note:
When the exterior temperature is - 3°C
to + 3°C, the °C characters flash (sig-
B nalling a risk of ice on the road).
If the power supply is cut (battery disconnected, supply wire cut, etc.), the clock
must be reset.
We recommend that you do not adjust these settings while driving.
1.74
REAR VIEW MIRRORS
Folding door mirrors
The door mirrors automatically fold out
when the vehicle is unlocked (switch 3
in position B). The door mirrors fold in
when the vehicle is locked.
In any case, you can make the rear view
mirrors fold in (switch 3 in position C) or
1 fold out (switch 3 in position A).
2 Automatic mode is then deactivated. To
reactivate it, position switch 3 to B.
3 4
A
B C
Objects observed in the door mirror glass are actually closer than they For safety reasons, carry
appear. For your safety, take this into account in order to correctly assess out any adjustments when
the distance before any manoeuvre. the vehicle is not being
driven.
1.75
EXTERIOR LIGHTING AND SIGNALS (1/4)
1 2 3
1.76
EXTERIOR LIGHTING AND SIGNALS (2/4)
Depending on the vehicle, the dipped Switching off the lights
beam headlights come on automati-
There are two possibilities:
1 2 3 cally after several sweeps of the wind-
screen wiper blades. – manually, move ring 2 to position 0;
– the lights will go out automatically
Main beam headlights when the engine is switched off, the
á With the engine running and
driver’s door is opened or the vehicle
is locked. In this case, the next time
the dipped beam headlights lit, push the engine is started the lights will be
stalk 1. This indicator light on the instru- switched back on according to the
ment panel comes on. position of the ring 2.
To return to the dipped headlight posi-
tion, pull stalk 1 towards you again. NB: if the fog lights are lit, the lights are
not switched off automatically.
Automatic operation
(depending on vehicle)
Turn ring 2 until the AUTO symbol is op-
posite mark 3: with the engine running,
the dipped beam headlights switch on
or off automatically depending on the
brightness of the light outside, without
any action on stalk 1.
1.77
EXTERIOR LIGHTING AND SIGNALS (3/4)
“Follow-me-home lighting”
function
1 2 3
This function allows you to briefly switch 1 4
on the dipped beam headlights (to pro-
vide light when opening a gate, etc.).
With the engine and lights switched
off and the ring 2 in position 0 or AUTO,
pull the stalk 1 towards you: the dipped
beam headlights come on for approxi-
mately thirty seconds. To increase this
duration, you may pull the stalk up to
four times (total time restricted to two 5
minutes). The message “Follow-me
home for _ _ _” along with the time the
lights will be on for is displayed on the
Welcome and goodbye Front fog lights
function
instrument panel to confirm this action.
You can then lock your vehicle. g Turn centre ring 4 on the
(depending on vehicle) To switch off the lights before they go stalk 1 until the symbol faces mark 5,
Once the function is activated, the side out automatically, turn ring 2 to any po- then release it.
lights come on automatically when the sition, then return it to position AUTO. Operation of the fog lights depends on
vehicle is unlocked. the exterior lighting position selected,
They switch off automatically: and an indicator light will light up on the
– approximately one minute after light- instrument panel.
ing up;
– when starting the engine based on
the position of the lighting stalk;
or
– upon locking the vehicle.
1.78
EXTERIOR LIGHTING AND SIGNALS (4/4)
Switching off the lights
Turn ring 4 again until mark 5 is oppo-
4 site the symbol for the fog light you wish
1 to switch off. The corresponding indi-
cator light goes out on the instrument
panel.
The front and rear fog lights switch off
when the exterior lights are switched
off.
Cornering lights
5 (depending on vehicle equipment)
Whenever the dipped beam headlights
are on and under certain conditions (at
Rear fog light speed, the steering wheel at an angle,
f Turn centre ring 4 on the stalk
in forward gear, the indicator lights on,
etc.), when taking a corner one of the
until the symbol faces mark 5, then re-
front fog lights will come on to light the
lease it.
inside of the bend.
Operation of the fog lights depends on
the exterior lighting selected, and an in-
dicator light will light up on the instru-
ment panel. When driving in fog or snow, or
when transporting objects which are
To avoid inconveniencing other road higher than the roof, the headlights
users, remember to switch off the rear do not come on automatically.
fog light when it is no longer needed.
Switching on the fog lights remains
the responsibility of the driver: the
indicator lights on the instrument
panel inform you whether the fog
lights are lit (indicator light on) or not
(indicator light not on).
1.79
AUDIBLE AND VISUAL SIGNALS
Direction indicators
Move stalk 1 parallel to the steering
wheel and in the direction you are going
to turn it. 2
1
One-touch mode
When driving, it is possible that the
A steering wheel may not be turned suf-
ficiently to return the stalk automatically
to its starting position.
In this case, move the stick 1 to half-
way, then release it: the stalk returns to
its original point and the indicator light
flashes three times.
1.80
HEADLIGHT BEAM ADJUSTMENT
5 doors Estate
1.81
WINDSCREEN WASH, WIPE (1/2)
Vehicles with automatic wiper
function
2
1 1 With the engine running, move stalk 1
E – A park.
A – B automatic wiper function
When this position is selected, the
B system detects water on the wind-
C screen and triggers the wipers at a
suitable wiping speed. It is possi-
D ble to change the triggering thresh-
old and the time sweeps by turning
F ring 2:
– E: minimum sensitivity
– F: maximum sensitivity
With the ignition on, move stalk 1 Special note
When driving, the wiping speed slows NB: in foggy weather or during
– A park.
down whenever the vehicle stops. The snowfalls, the wiping is not automati-
– B intermittent wiping. speed will change from fast wiping cally triggered and remains under
The wipers will pause for several speed to normal wiping speed. the driver’s control.
seconds between sweeps. It is As soon as the vehicle moves off, – C normal wiping speed.
possible to change the time be- wiping will return to the speed originally
tween sweeps by turning ring 2. selected. If stalk 1 is operated, it over- – D fast wiping speed.
– C normal wiping speed. rides and cancels the automatic func-
tion.
– D fast wiping speed.
1.82
WINDSCREEN WASH, WIPE (2/2)
1
1
A
B In freezing or snowy weather, ensure
they are not stuck to the windscreen
C (including the central area located
D behind the interior rear-view mirror)
and the rear screen before starting
the wipers (risk of motor overheat-
ing).
Check the condition of the wiper
blades. You are responsible for their
Windscreen washer service life:
With the ignition on, pull stalk 1 to- – they must remain clean: clean
wards you. the blades, windscreen and
rear screen regularly with soapy
A brief pull will trigger a single sweep water;
of the wipers, in addition to the wind- – do not use them when the wind-
screen washer. screen or rear screen are dry;
A longer pull will trigger three sweeps – free them from the windscreen or
of the wipers followed, a few seconds rear screen when they have not
later, by a fourth, in addition to the wind- Before any action involving been used for a long time.
screen washer. the windscreen (washing In all cases, replace them as soon
the vehicle, de-icing, clean- as they begin to lose efficiency: ap-
ing the windscreen, etc.) proximately once a year.
return stalk 1 to position A (park). Before using the windscreen wiper,
Risk of injury and/or damage. check that no objects are obstruct-
ing the travel of the blade.
1.83
REAR SCREEN WASH, WIPE
Rear screen wash/wipe
p With the ignition on, turn the
end of stalk 1 to align mark 2 with the
2 1 symbol.
When the stalk is released, it returns to
the rear wipe position.
Special note
If the windscreen wipers are operat-
ing or are in automatic mode, the rear
screen wiper wipes intermittently when Check the condition of the wiper
reverse gear is engaged. blades. You are responsible for their
service life:
– they must remain clean: clean
Speed-dependent the blades and the rear screen
Y timed rear screen regularly with soapy water;
wiper – do not use them when the rear
screen is dry;
With the ignition on, turn the end of – free them from the rear screen
stalk 1 to align mark 2 with the symbol. when they have not been used
Wiping frequency varies with speed. for a long time.
In all cases, replace them as soon
as they begin to lose efficiency: ap-
Before any action on the proximately once a year.
rear screen (washing the Before using the rear wiper, check
vehicle, de-icing, cleaning that no object obstructs the travel of
When working in the engine the windscreen, etc.) return the blade.
compartment, ensure that stalk 1 to the park position. Do not use the wiper arm to open or
the windscreen wiper stalk close the tailgate.
is in the park position. Risk of injury or damage.
Risk of injury.
1.84
FUEL TANK (1/3)
Fuel grade Petrol version
Use a high-grade fuel that complies It is essential to use unleaded petrol.
with the legislation in force in each The octane rating (RON) must comply
country and which must comply with with the information given on the label
the specifications given on the label on the cover A. Refer to Section 6 for
1 A on the cover A. Please refer to the in- information on “Engine specifications”.
formation on “Engine specifications” in
Section 6.
Diesel version
2 B
Only use diesel fuel which complies
with the information on the label located
inside the cover A.
1.85
FUEL TANK (2/3)
Filling with fuel
With the ignition off, insert the nozzle
and insert it fully before turning it on to
fill the fuel tank (risk of splashing).
3
Keep the nozzle in this position through-
out the entire filling operation.
When the pump cuts out automatically
at the end of the filling procedure, a
maximum of two further filling attempts
may be made, as there must be suffi-
cient space in the fuel tank to allow for
expansion.
Make sure that no water enters the fuel
tank during filling. The cover A and its
surround must remain clean.
1.86
FUEL TANK (3/3)
3 5
No modifications what-
soever are permitted on
any part of the fuel supply
system (electronic units,
Running out of fuel on diesel Vehicles without priming bulb 4
wiring, fuel circuit, injectors, pro-
versions Insert the RENAULT card into the 5 tective covers, etc.) as this may be
Vehicles with priming bulb 4 card reader. Press the start button 3 dangerous (unless undertaken by
After a breakdown caused by com- without pressing any of the pedals. Wait qualified Network personnel).
pletely running out of fuel, the system a few minutes before starting. This will
must be reprimed before the engine is enable the fuel circuit to be primed. If
restarted: the engine does not start, repeat the
Fill the tank with at least 8 litres of procedure.
diesel fuel.
Press priming bulb 4 several times.
The engine can now be restarted.
If the engine does not start after several The engine may be hot
attempts, contact an approved Dealer. when working in close prox-
imity. In addition, the engine
cooling fan may come on at
any moment.
Risk of injury.
1.87
1.88
Section 2: Driving
(Advice on use relating to fuel economy and the environment)
Running in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.2
Starting/stopping the engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.3
Stop and Start Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.6
Special features of petrol versions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.10
Special features of diesel versions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.11
Gear lever/Handbrake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.12
Eco-driving. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.13
Maintenance and antipollution advice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.18
Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.19
Tyre pressure loss warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.20
Driver correction devices/aids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.23
Speed limiter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.27
Cruise control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.30
Parking distance control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.34
Reversing camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.38
Assisted parking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.40
Automatic gearbox. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.44
2.1
RUNNING IN
Petrol version Diesel version
For the first 600 miles (1,000 km), do For the first 1,000 miles (1,500 km),
not exceed 78 mph (130 km/h) in the do not exceed 80 mph (130 km/h) in
highest gear, or 3,000 to 3,500 rpm. the highest gear, or 2,500 rpm. After
You may only expect top performance completing this mileage you may drive
from your vehicle after approximately faster, although you may only expect
1,800 miles (3,000 km). top performance after approximately
3,600 miles (6,000 km).
Service intervals: refer to the
Maintenance Document for your vehi- During the running in period, do not ac-
cle. celerate hard while the engine is still
cold and do not let the engine over-rev.
Service intervals: refer to the
Maintenance Document for your vehi-
cle.
2.2
STARTING, STOPPING THE ENGINE (1/3)
1 2
Driver’s responsibility
3 when parking or stopping
the vehicle
Never leave an animal,
child or adult who is not self-suffi-
cient alone in your vehicle, even for
a short time.
Remote control RENAULT Hands-free RENAULT card They may pose a risk to themselves
or to others by starting the engine,
card The RENAULT card must be inserted activating equipment such as the
When you get into the vehicle, insert in card reader 2 or in detection zone 3. electric windows or locking the
the RENAULT card integrated key, To start, depress the brake or clutch doors, for example.
pointing towards you, fully into the card pedal and press button 1. If a gear is Also, in hot and/or sunny weather,
reader 2. engaged, the vehicle may only be star- please remember that the tempera-
To start, press button 1. If a gear is en- ted by depressing the clutch pedal. ture inside the passenger compart-
gaged, depress the clutch pedal to start ment increases very quickly.
the vehicle. Starting with the boot open in
hands-free mode RISK OF DEATH OR SERIOUS
INJURY.
In this case, the RENAULT card must
not be located in the luggage compart-
ment.
2.3
STARTING, STOPPING THE ENGINE (2/3)
Special features Operating faults
vehicles with an automatic gearbox In certain cases, the hands-free
The lever should be in position P. RENAULT card may not work:
1 2 – when the RENAULT card battery is
All vehicles drained, flat battery, etc.
– If one of starting conditions is not ap- – near to appliances operating on the
plied, the message “PRESS BRAKE same frequency as the card (mo-
+ START” or “PRESS CLUTCH + nitor, mobile phone, video game,
START” or “SELECT PARK” is dis- etc.);
played on the instrument panel; – vehicle located in a high electroma-
– in some cases it will be necessary gnetic radiation zone.
to move the steering wheel while The message “PLEASE INSERT
pressing the start button 1 to help KEYCARD” appears on the instrument
unlock the steering column; the mes- panel.
sage “TURN STEERINGWHEEL + Insert the RENAULT card fully into card
START” warns you. For other functions: reader 2.
– in the event of starting the engine
in very low exterior temperatures – vehicles with remote control
(lower than -10°C): hold down the RENAULT card, insert the card into Conditions for stopping the
clutch pedal until the engine starts. reader 2; engine
– vehicles with a RENAULT “hands- The vehicle must stationary, with the
free” card, with the card in the pas- lever positioned in N or P for vehicles
Accessories function senger compartment or inserted in
(switching on the ignition) with an automatic transmission.
the card reader 2, press button 1 wi-
Once you have gained access to your thout depressing the pedals.
vehicle, you may use some of its func- Note: depending on the vehicle, pres-
tions (radio, navigation, wipers, etc.). sing button 1 starts the engine.
2.4
STARTING, STOPPING THE ENGINE (3/3)
Remote control RENAULT card Hands-free RENAULT card
With the card in reader 2, press With the card in the vehicle, press
button 1: the engine will stop. Removing button 1: the engine stops. The stee-
1 2 the card from the reader locks the stee- ring column is locked when the driver’s
ring column. door is opened or the vehicle is locked.
Special feature If the card is no longer in the pas-
If the card is no longer in the reader senger compartment when you try to
when you try to switch the engine off, switch the engine off, the message
the message “NO KEYCARD PRESS “NO KEYCARD PRESS AND HOLD”
AND HOLD” will appear on the in- appears on the instrument panel: press
strument panel: press the button 1 for button 1 for longer than two seconds
longer than two seconds.
Special feature
Depending on the vehicle, accessories When you leave your vehicle, especially if you have your RENAULT card
(e.g. radio) stop working either when with you, check that the engine is completely switched off.
the engine is switched off or when the
driver’s door is opened or when the
doors are locked.
Driver’s responsibility when parking or stopping the vehicle
Never leave an animal, child or adult who is not self-sufficient alone in
Never switch off the igni- your vehicle, even for a short time.
tion before the vehicle has They may pose a risk to themselves or to others by starting the engine, ac-
stopped completely. Once tivating equipment such as the electric windows or locking the doors, for example.
the engine has stopped, the Also, in hot and/or sunny weather, please remember that the temperature inside
brake servo, power-assisted steer- the passenger compartment increases very quickly.
ing, etc. and the passive safety de- RISK OF DEATH OR SERIOUS INJURY.
vices such as air bags and preten-
sioners will no longer operate.
2.5
STOP AND START FUNCTION (1/4)
This system enables a reduced fuel For vehicles equipped with manual
consumption and lower greenhouse gearboxes:
gas emissions. The system is acti- – the gearbox is in neutral;
vated automatically when the vehicle is and
started. While driving, the system stops – the clutch pedal is released.
the engine (standby) when the vehicle
is at a standstill (traffic jam, traffic lights,
etc).
If the warning light flashes,
this means that the clutch pedal is
not sufficiently released;
and
Conditions for engine – the vehicle speed is less than ap-
standby proximately 7 mph (3 km/h).
The vehicle has set off from where it
was parked;
For vehicles equipped with auto-
In all vehicles, the warning light
on the instrument panel is lit when the
matic gearboxes: engine is on standby.
– the gearbox is in position D, M or N; The vehicle equipment remain opera-
and tional while the engine is stopped.
– the brake pedal is depressed (suffi- Keep your vehicle station-
ciently hard); ary when the engine is
and on standby (shown by the
– the accelerator pedal is not de-
pressed;
warning light
instrument panel).
on the
and
– the speed is zero for around
1 second.
The engine remains on standby if posi-
tion P is selected, or if position N is se- Before getting out of the
lected with the handbrake engaged and vehicle, you must switch
the brake pedal released. off the ignition by pressing
If the engine stalls while the system the engine stop (please see
is in operation, pressing the clutch “Starting, stopping the engine”).
pedal right down will start it again.
2.6
STOP AND START FUNCTION (2/4)
Preventing the engine from Conditions for coming out of Special note: depending on the vehi-
standing by engine standby cle, if you switch off the ignition when
the engine is on standby, the warning
In certain situations, such as negotiat- For vehicles equipped with auto-
ing a crossroads for instance, it is pos-
sible to keep the engine running so as
matic gearboxes: lightÄ is displayed for a few sec-
onds on the instrument panel.
– the brake pedal is released, position
to be ready to move off quickly. D or M engaged or,
For vehicles equipped with auto- – the brake pedal is released, position
matic gearboxes: N engaged and the handbrake off, or
Keep the vehicle stationary without – the brake pedal is pressed again,
pressing too hard on the brake pedal with position P engaged or position
N engaged with the handbrake ap-
For vehicles equipped with manual plied, or
gearboxes: – position R is engaged or,
Keep the clutch pedal pressed right – the accelerator pedal is pressed.
down For vehicles equipped with manual
gearboxes:
– the gearbox is in neutral and the
clutch pedal is slightly depressed, or
– the engine is in gear and the clutch
pedal is pressed right down.
2.7
STOP AND START FUNCTION (3/4)
Conditions preventing the – for vehicles with automatic gear- Special cases
standby of the engine boxes, the gradient is steeper than
approximately 12%; With the engine on standby (traffic jam,
Certain conditions prevent the system traffic lights, etc.), if the driver unfastens
from using the engine standby function, – the “Clear View” function is activated their seat belt, opens the driver’s door
including when: (please see “Automatic Climate or gets out of their seat, the ignition will
Control” in Section 3); be switched off.
– reverse gear is engaged;
– the engine temperature is too low; To restart and reactivate the Stop and
– the bonnet is not locked; Start system, press the start button
– the emission control system is being
– the driver’s door is not closed; regenerated; (please refer to “Starting, stopping the
or engine” in Section 2).
– the driver’s seatbelt is not fastened;
– ...
– the outdoor temperature is too low or
too high (less than around 0 °C or
higher than around 30 °C);
Warning light is displayed on the
instrument panel. This notifies you that
– the battery is not sufficiently charged; engine standby is not available.
– the difference between the vehicle
interior temperature and the auto-
matic climate control instruction is
too high;
2.8
STOP AND START FUNCTION (4/4)
Special feature of the automatic The system reactivates automati-
engine re-start cally each time the vehicle is started
Under certain conditions, the engine using the start button (please refer
can restart on its own in order to guar- to “Starting, stopping the engine” in
antee your safety and comfort. Section 2).
1
This can occur especially when:
– the outdoor temperature is too low or Operating faults
too high (less than around 0 °C or When the message “Check Stop &
higher than around 30 °C); Start” appears on the instrument panel
– the “Clear View” function is activated 2 and the integrated warning light 2 lights
(please see “Automatic Climate up on the switch 1, the system is deac-
Control” in Section 3); tivated.
– the battery is not sufficiently charged; Please consult an authorised dealer.
– the vehicle speed is above 3 mph
(5 km/h) (downhill slope, etc.);
– repeated pressing on the brake Deactivating, activating the
pedal or braking system require-
ment;
function
– ... Press switch 1 to deactivate the func-
tion. The message “Stop & Start deac-
tivated” will appear on the instrument
panel and the integrated warning light 2
on the switch will light up.
Pressing again will reactivate the
system. The message “Stop & Start ac-
tivated” will appear on the instrument
panel and the integrated warning light 2
In the event of an emer- on switch 1 will go out. Before getting out of the
gency, the engine can be vehicle, you must switch
restarted by pressing on the off the ignition by pressing
clutch pedal if the Stop and the engine stop (please see
Start function is activated. Note: With the engine on standby, “Starting, stopping the engine”).
press switch 1 to automatically re-
start the engine.
2.9
SPECIAL FEATURES OF PETROL VERSIONS
The following operating conditions: If you notice any of the above operating
– driving for long periods when the low faults, have the necessary repairs car-
fuel level warning light is lit; ried out as soon as possible by an ap-
proved Dealer.
– using leaded petrol;
These faults may be avoided by regu-
– using fuel or lubrication additives larly taking your vehicle to an approved
which are not approved. Dealer at the intervals specified in the
Or operating faults such as: Maintenance document.
– faulty ignition system, running out of
fuel or disconnected spark plugs re- Starting problems
sulting in the engine misfiring or cut- To avoid damaging the catalytic con-
ting out when driving; verter, do not keep trying to start the
– loss of power, engine (using the start button, or by
pushing or towing the vehicle) without
as they may cause the catalytic con-
having identified and corrected the
verter to overheat and thus reduce its
starting fault.
efficiency, or damage it irreparably
and cause heat damage to the vehi- If the fault cannot be identified, do not
cle. keep trying to start the engine, but con-
tact an approved Dealer.
2.10
SPECIAL FEATURES OF DIESEL VERSIONS
Diesel engine speed Precautions to be taken in
Diesel engines are fitted with injection winter
equipment which prevents the engine To avoid any faults in icy weather:
speed being exceeded irrespective of
the gear selected. – ensure that the battery is always fully
charged,
If the message “CHECK ANTI-
POLLUTION SYSTEM” is displayed – always keep the diesel tank re-
latively full to avoid water vapour
along with warning lights Ä
and
©, consult an authorised dealer
condensing in it and accumulating at
the bottom of the tank.
immediately.
When driving, depending on the fuel
grade used, it is possible that white
smoke may be emitted.
This is due to the exhaust particle filter
being cleaned automatically, and does
not affect the way the vehicle runs.
2.11
GEAR LEVER/HANDBRAKE
Note: depending on the vehicle, if the
dipped beam headlights are on, the
front fog lights come on simultaneously
when reverse gear is selected.
1
Handbrake
2 When stationary, and de-
To release: pending on the slope and/or
3 Pull the lever 3 up slightly, press vehicle load, it may be nec-
button 2 and then lower the lever to the essary to pull up the hand-
floor. brake at least two extra notches and
The red warning light on the instrument engage a gear (1st or reverse gear)
panel will come on if you are driving for vehicles with a manual gearbox
with an incorrectly released handbrake. or position P for vehicles with an au-
tomatic gearbox.
To apply:
Gear lever Pull lever 3 upwards. Check that the
Vehicles with manual gearbox: refer vehicle is immobilised. The warning
to the grid on the gear lever knob 1.
Vehicles with automatic gear-
D
light
come on.
on the instrument panel will
2.12
DRIVING ADVICE, ECO DRIVING (1/5)
Fuel consumption is accredited in ac- Driving style indicator 2
cordance with a standard regulatory
Informs you about the driving style
method. Identical for all manufactu-
adopted in real time. You will be notified
rers, this enables vehicles to be com-
by the colour of warning light 2.
pared with one another. Consumption
in real time depends on vehicle usage 1 – Green: measured, economical driv-
conditions, the equipment fitted and the ing;
user’s driving style. To optimise fuel – Yellow: opt for a calmer driving style;
consumption, please refer to the fol- – Orange: driving too fast.
lowing advice. To activate/deactivate the driving style
2
Depending on the vehicle, you will have indicator, please see the multimedia
various functions which enable you to system instructions.
lower your fuel consumption:
– the rev counter;
– gear change indicator;
– the driving style indicator; Gear change indicator 1
– the journey record and eco-driving
advice via the multimedia display; To obtain optimum consumption levels,
– ECO mode activated by the ECO a warning light on the instrument panel
button. lets you know the best time to move up
or down a gear:
If fitted on the vehicle, the navigation
system provides additional information.
Š move up a gear;
2.13
DRIVING ADVICE, ECO DRIVING (2/5)
An overall rating from 0 to 100 is dis-
played to let you assess your eco driv-
ing performance. The higher the rating,
the lower the fuel consumption.
3 Eco advice is given to help improve
your performance.
With your favourite journeys saved, you
can evaluate your performance.
For more information, please see the
multimedia system instructions.
Journey record
Once the engine is switched off, you
will see “Journey record” displayed on
the screen 3, enabling you to view in-
formation relating to your last journey.
This indicates:
– average fuel consumption;
– number of miles/kilometres travelled;
– number of miles/kilometres saved.
2.14
DRIVING ADVICE, ECO DRIVING (3/5)
ECO mode
ECO mode is a function which op-
timises fuel consumption. It acts on
certain power consuming systems in
the vehicle (heating, air conditioning,
power-assisted steering etc.) and on
certain driving actions (acceleration,
gear changing, cruise control, deceler-
ation etc.).
4
5
2.15
DRIVING ADVICE, ECO DRIVING (4/5)
– Avoid sudden acceleration.
– Brake as little as possible. If you an-
ticipate an obstacle or bend in ad-
vance, you may then simply release
the accelerator pedal.
– Do not try to maintain the same
speed up a hill, accelerate no more
than you would on the level. Keep
your foot in the same position on the
accelerator pedal.
– Double declutching and accelerating
before switching off are unnecessary
in modern vehicles.
– Bad weather, flooded roads:
2.16
DRIVING ADVICE, ECO DRIVING (5/5)
– In vehicles fitted with air condi-
tioning, it is normal to observe an
increase in fuel consumption (espe-
cially in urban conditions) when it is
used. For vehicles fitted with manual
air conditioning, switch off the system
when it is not required.
Advice for reducing consumption
and therefore helping to preserve
the environment:
If the vehicle has been parked in the
sun, open the doors for a few mo-
ments to let the hot air escape before
starting the engine.
– Do not leave an empty roof rack
Tyres Advice on use fitted to the vehicle.
– It is better to fit a trailer for bulky ob-
– An underinflated tyre increases fuel – Favour the ECO mode. jects.
consumption. – Electricity is fuel; switch off all the – When towing a caravan, fit a wind
– The use of non-recommended tyres electrical components which are deflector and adjust it carefully.
can increase fuel consumption. not really needed. However (safety – Avoid using the car for door-to-door
first), keep your lights on when the calls (short journeys with long waits
visibility is bad (“see and be seen”). in between) because the engine
– Use the air vents. Driving with the never reaches its normal operating
windows open at 60 mph (100 km/h) temperature.
will increase fuel consumption by
4%.
– Never fill the fuel tank right to the
brim to avoid overflow.
2.17
MAINTENANCE AND ANTIPOLLUTION ADVICE
Your vehicle complies with criteria for In addition, replacing engine, fuel – Air filter, fuel filter: a choked ele-
recycling and recovering vehicles at the supply system and exhaust compo- ment will reduce efficiency. It must
end of their service life, which entered nents with parts other than those origi- be replaced.
into force in 2015. nally recommended by the manufac- – Ignition and idle speed: no adjust-
Some parts of your vehicle have there- turer may alter your vehicle so that it ment is needed.
fore been designed to facilitate future no longer complies with anti-pollution
recycling. regulations.
Exhaust gas monitoring
These parts are easy to remove so Have your vehicle adjusted and system
that they can be recovered and reproc- checked by an authorised dealer, in ac-
cordance with the instructions given in The exhaust gas monitoring system will
essed by recycling companies. detect any operating faults in the vehi-
your maintenance schedule: they will
By virtue of its design, moderate fuel have all the equipment necessary for cle’s antipollution system.
consumption and initial settings, your ensuring that your vehicle is maintained If this system malfunctions, toxic sub-
vehicle also conforms to current anti- to its original standard. stances may be released into the at-
pollution regulations. The manufac- mosphere or damage may occur.
turer is actively striving to reduce pol- This warning light on the in-
lutant exhaust gas emissions and to
save energy. But the fuel consumption
Engine adjustments
– Spark plugs: for optimum condi-
Ä strument panel will indicate if
there are any faults in the system:
of your vehicle and the level of pollutant tions of use, output and performance This lights up when the ignition is
exhaust gas emissions are also your the specifications laid down by our switched on and goes out when the
responsibility. Ensure that it is main- Design Department must be strictly engine is started.
tained and used correctly. applied.
– If it lights up continuously, consult an
If the spark plugs have to be changed, approved Dealer as soon as possi-
Maintenance use the make, type and gap specified ble;
It is important to remember that fail- for your vehicle’s engine. Contact an
authorised dealer for this. – if it flashes, reduce the engine speed
ure to respect antipollution regulations until the light stops flashing. Contact
could lead to legal action being taken an authorised dealer as soon as pos-
against the vehicle owner. sible.
2.18
ENVIRONMENT
Your vehicle has been designed with Emissions – At the end of the vehicle’s service
respect for the environment in mind for life, it should be sent to approved
its entire service life: during production, Your vehicle has been designed to centres to ensure that it is recycled.
use and at the end of its life. emit fewer greenhouse gases (CO2)
while in use, and therefore to consume – In all cases, comply with local legis-
This commitment is illustrated by the lation.
Renault eco² signature. less fuel (eg. 140 g/km, equivalent to
5.3 l/100 km for a diesel vehicle).
Our vehicles are also equipped with a Recycling
Manufacture particle filter system including a cata-
Your vehicle is 85% recyclable and
Your vehicle has been manufactured at lytic converter, an oxygen sensor and
95% recoverable.
a factory which complies with a policy an active carbon filter (the latter pre-
to reduce the environmental impact vents vapour from the fuel tank being To achieve these objectives, many of
on the surrounding areas (reduction of released into the open air). the vehicle components have been de-
water and energy consumption, visual signed to enable them to be recycled.
For certain diesel vehicles, this system
and noise pollution, atmospheric emis- The materials and structures have
also has a particle filter to reduce the
sions and waste water; sorting and re- been carefully designed to allow these
volume of soot particles emitted.
using waste). components to be easily removed and
reprocessed by specialist companies.
Please make your own In order to preserve raw material re-
contribution towards sources, this vehicle incorporates nu-
protecting the environment merous parts made from recycled plas-
too tics or renewable materials (vegetable
or animal-derived materials such as
– Worn parts replaced in the course of cotton or wool).
routine vehicle maintenance (vehi-
cle battery, oil filter, air filter, batter-
ies, etc.) and oil containers (empty or
filled with used oil) must be disposed
of through specialist organisations.
2.19
TYRE PRESSURE LOSS WARNING (1/3)
Operating principle In the following situations, the system
This system detects a loss of pressure risk coming into action late or not func-
in one of the tyres by measuring the tioning correctly:
wheel speed while driving. – system not reset after reinflation or
any operation on the wheels;
Warning light 1 comes on to
alert the driver in the event of insuffi-
– system badly reset: different inflation
pressures from the recommended
cient pressure (deflated wheel, punc- pressures;
1 – significant change in load or distribu-
tured tyre, etc.).
tion of load on one side of the vehi-
Operating conditions cle;
The system should be reset with an – sporty driving with strong accelera-
inflation pressure equal to that given tion;
on the tyre inflation pressure label. – driving on snowy or slippery surface;
Otherwise it risks not giving a reliable – driving with snow chains;
warning in the event of a significant loss – fitting a single new tyre;
If fitted on the vehicle, this system – use of tyres not approved by the net-
warns the driver of pressure loss in one of pressure. Please refer to the informa-
tion on “Tyre pressures” in Section 4. work.
or several tyres. – ...
2.20
TYRE PRESSURE LOSS WARNING (2/3)
Resetting the standard level for the Display
tyre pressures 2 The display 2 on the instrument panel
This should be done: informs you of any tyre pressure faults
(flat tyre, punctured tyre, etc.).
– after each reinflation or readjustment 3
of the pressure of one of the tyres; “INFLATE TIRES AND SET TPW”
2.21
TYRE PRESSURE LOSS WARNING (3/3)
“RECALIBRATE SET TPW” Readjustment of tyre pressures After each change of wheel/tyre, read-
The tyre pressures must be adjusted just the tyre pressure and launch the
The warning light flashes for
several seconds, then stays on, along
when cold (please refer to the label lo- reset of the tyre pressure reference
value.
cated on the edge of the driver’s door).
with the message “RECALIBRATE SET
TPW”. If tyre pressures cannot be checked Emergency spare wheel
when the tyres are cold, the recom- If fitted on the vehicle, readjust the tyre
They indicate that the request to reset mended pressures should be increased
the reference value of the tyre pres- pressure and launch the reinitialisation
by 0.2 to 0.3 bar (3 PSI). of the tyre pressure reference value.
sures must be restarted.
Never deflate a hot tyre.
“TPW NOT AVAILABLE” Tyre repair product and inflation kit
After each reinflation or readjustment of
The warning light flashes for sev-
eral seconds, then stays on, along with
the tyre pressure, launch the reinitiali-
sation of the tyre pressure reference
Only use equipment approved by the
brand network, or the system risks
value. being activated late or not operating
the message “TPW NOT AVAILABLE”.
correctly. Please refer to “Tyre inflation
They indicate that the vehicle is
Replacing wheels/tyres kit” in Section 5.
equipped with an emergency spare
wheel which is smaller than the other Only use equipment approved by the After using the tyre inflation kit, readjust
four and that it is fitted to the vehicle. brand network, or the system risks the tyre pressure and launch the reini-
being activated late or not operating tialisation of the tyre pressure reference
“CHECK TPW”
correctly. Please see the information on value.
“Tyres” in Section 5.
The warning light flashes for
several seconds, then stays on, along
with the message “CHECK TPW”.
This message is accompanied by the
warning light ©.
They indicate a system fault. Please
consult an authorised dealer.
2.22
DRIVER CORRECTION DEVICES AND AIDS (1/4)
Depending on the vehicle, this is com- Anti-lock braking system Operating faults:
posed of: (ABS)
– anti-lock braking system (ABS);
– electronic stability program (ESC) Under heavy braking, the ABS prevents
– © and x lit up on the in-
strument panel alongside messages
with understeer control and trac- the wheels from locking, allowing the “CHECK ABS”, “CHECK BRAKING
tion control; stopping distance to be managed and SYSTEM” and “CHECK ESC”: ABS,
– emergency brake assist; keeping control of the vehicle. ESC and emergency brake assist
– hill start assistance. Under these circumstances, the vehi- are deactivated. Braking is always
cle can be steered to avoid an obstacle enabled;
whilst braking. In addition, this system
can increase stopping distances, par-
ticularly on roads with low surface grip
– xD , , © and ® lit
up on the instrument panel alongside
(wet ground etc.).
the message “BRAKING SYSTEM
You will feel a pulsation through the
FAULT”: this indicates a fault in
These functions are an ad- brake pedal each time the system is
the braking system.
ditional aid in the event of activated. The ABS does not in any
critical driving conditions, way improve the vehicle's physical per- In both cases, consult an approved
enabling the vehicle behav- formance relating to the road surface Dealer.
iour to be adapted to suit the driving and road-holding. It is still essential to
conditions. follow the rules of good driving practice
These functions do not take the (such as driving at a safe distance from
place of the driver. They do not the vehicle in front etc.).
increase the vehicle’s limits and
should not encourage you to
drive more quickly. Therefore,
they can under no circumstances Your braking systems
replace the vigilance or responsibil- are partially operational.
ity of the driver when manoeuvring However, it is dangerous
the vehicle (the driver must always In an emergency, apply firm and to brake suddenly and
be ready for sudden incidents which continuous pressure to the brake it is essential to stop immediately,
may occur when driving). pedal. There is no need to pump as soon as traffic conditions allow.
it repeatedly. The ABS will modu- Contact an approved dealer.
late the force applied in the braking
system.
2.23
DRIVER CORRECTION DEVICES AND AIDS (2/4)
Electronic stability program Understeer control Operating faults
(ESC) with understeer control This system optimises the action of the When the system detects an operating
and traction control ESC in the case of pronounced under- fault the message “CHECK ESC” and
steer (loss of front axle road holding).
Electronic stability control ESC
Traction control
warning light © and appear
on the instrument panel. In this case,
This system helps you to keep control the ESC and traction control system
of the vehicle in critical driving condi- This system helps to limit wheelspin of are deactivated.
tions (avoiding an obstacle, loss of grip the drive wheels and to control the ve-
on a bend, etc.). hicle when pulling away accelerating or Consult an approved dealer.
decelerating.
Operating principle Disabling the traction control
Operating principle system
A sensor in the steering wheel detects
Using the wheel sensors, the system
the direction selected by the driver. In some situations (driving on very wet
measures and compares the speed of
Other sensors throughout the vehicle the drive wheels at all times and slows ground: snow, mud, etc. or driving with
measure the actual direction. down their over-rotation. If a wheel is snow chains fitted), the system may
starting to slip, the system brakes au- reduce the engine output to limit whee-
The system compares driver input to lspin.
the actual trajectory of the vehicle and tomatically until the drive supplied be-
corrects the trajectory if necessary by comes compatible with the level of grip
controlling the braking of certain wheels under the wheel again.
and/or engine power. In the event that The system also adjusts the engine
the system is engaged, indicator light speed to the grip available under the
wheels, independently of the pressure
flashes on the instrument panel. exerted on the accelerator pedal.
2.24
DRIVER CORRECTION DEVICES AND AIDS (3/4)
Emergency brake assist Hazard warning lights switching on
Depending on the vehicle, these may
This system supplements the ABS light up in the event of sudden decel-
and helps reduce vehicle stopping dis- eration.
tances.
Braking anticipation
Operating principle Depending on the vehicle, when you
The system is for detecting an emer- rapidly release the accelerator, the
gency braking situation. In this case, system anticipates the braking ma-
the braking assistance immediately de- noeuvre in order to reduce stopping
velops maximum power and may trig- distances.
ger ABS regulation. When using the cruise control:
ABS braking is maintained as long as – if you use the accelerator, when you
the brake pedal is applied. release it, the system may be trig- These functions are an ad-
gered; ditional aid in the event of
– if you do not use the accelerator, the critical driving conditions,
system will not be triggered. enabling the vehicle behav-
Operating faults iour to be adapted to suit the driving
When the system detects an operating conditions.
fault the message “CHECK BRAKING These functions do not take the
SYSTEM” appears on the instrument place of the driver. They do not
panel along with the © warning increase the vehicle’s limits and
light. should not encourage you to
drive more quickly. Therefore,
Consult an approved dealer.
they can under no circumstances
replace the vigilance or responsibil-
ity of the driver when manoeuvring
the vehicle (the driver must always
be ready for sudden incidents which
may occur when driving).
2.25
DRIVER CORRECTION DEVICES AND AIDS (4/4)
Hill start assistance The hill start assistance
Depending on the gradient of the in- system cannot completely
cline, this system assists the driver prevent the vehicle from
when starting on a hill. It prevents the rolling backwards in all sit-
vehicle from rolling backwards, de- uations (extremely steep gradients
pending on the slope, by automatically etc.).
applying the brakes when the driver lifts
In all cases, the driver may depress
his/her foot off the brake pedal to de-
the brake pedal to prevent the vehi-
press the accelerator pedal.
cle from rolling backwards.
System operation The hill start assistance function
It only operates when the gear lever is should not be used for prolonged
in a position other than neutral (other stops: use the brake pedal.
than N or P for automatic transmis- This function is not designed to im-
sions) and the vehicle is completely mobilise the vehicle permanently.
stationary (brake pedal depressed)
If necessary, use the brake pedal to
The system holds the vehicle for ap- stop the vehicle.
proximately 2 seconds. The brakes are
The driver must remain particularly
then gradually released (the vehicle will
vigilant when driving on slippery or
move according to the slope).
low-grip surfaces and/or on hills.
Risk of serious injury.
2.26
SPEED LIMITER (1/3)
2 3 4 5
2.27
SPEED LIMITER (2/3)
Varying the limit speed Exceeding the limit speed
The limit speed may be changed by re- It is possible to exceed the limit speed
peatedly pressing: at any time. To do this: press the accel-
– switch 2 (+) to increase speed; erator pedal firmly and fully (beyond
the resistance point).
– switch 3 (-) to reduce speed.
2 3 While the speed is being exceeded, the
programmed speed displayed on the
instrument panel flashes.
Then, release the accelerator: the
speed limiter function will return as
soon as you reach a speed lower than
the stored speed.
2.28
SPEED LIMITER (3/3)
Recalling the limit speed
If a speed has been saved, it can be re-
called by pressing switch 4 ((R)).
2 3 4 5
2.29
CRUISE CONTROL (1/4)
2 3 4 5
1
This function is an addi-
tional driving aid. However,
the function does not take
the place of the driver.
Therefore, it can under no circum-
The cruise control function helps you to stances replace the driver’s respon- Controls
maintain your driving speed at a speed sibility to respect speed limits and to
that you choose, called the cruising 1 Main “On/Off” switch.
be vigilant (the driver must always
speed. be ready to brake). 2 Cruising speed activation, storage
This cruising speed may be set at any and increase switch (+).
Cruise control must not be used in
speed above 20 mph (30 km/h). heavy traffic, on undulating or slip- 3 Decreasing cruising speed (-).
pery roads (black ice, aquaplan- 4 Activation with recall of saved cruis-
ing, gravel) and during bad weather ing speed (R).
(fog, rain, side winds etc.).
5 Switch the function to standby (with
There is a risk of accidents. cruising speed saved) (O).
2.30
CRUISE CONTROL (2/4)
6 2 3
2.31
CRUISE CONTROL (3/4)
Exceeding the cruising speed
The cruising speed may be exceeded
at any time by depressing the accelera-
tor pedal. While it is being exceeded,
the cruising speed flashes on the in-
strument panel.
2 3
Then, release the accelerator: after a
few seconds, the vehicle will automati-
cally return to its set cruising speed.
2.32
CRUISE CONTROL (4/4)
Returning to the cruising speed
If a speed is stored, it can be recalled,
once you are sure that the road con-
ditions are suitable (traffic, road sur-
face, weather conditions, etc.). Press
switch 4 (R) if the vehicle speed is
2 3 4 5 above 20 mph (30 km/h).
When the stored speed is recalled, acti-
vation of the cruise control is confirmed
by the illumination of the warning 1
light.
NB: if the speed previously stored is
much higher than the current speed,
the vehicle will accelerate more rapidly
to reach this threshold.
Putting the function on Switching off the function
standby The cruise control function is deacti-
The function is set to standby if you: vated if you press switch 1: in this case
a speed is no longer stored. The two in-
– use the switch 5 (O);
strument panel warning lights and
– the brake pedal; go out to confirm that the function is
– depress the clutch pedal or shift into deactivated.
neutral if the vehicle has an auto-
matic gearbox.
In all three cases, the cruising speed
remains stored and the message When the cruise control function is
Putting the cruise control
“MEMORISED” appears on the instru- put on standby, pressing switch 2
on standby or switching it
ment panel. (+) reactivates the cruise control
off does not cause a rapid
function without taking into account
Standby is confirmed when indicator reduction in speed: you
the stored speed: it is the speed at
light goes out. must brake by depressing the brake
which the vehicle is moving that is
pedal.
taken into account.
2.33
PARKING DISTANCE CONTROL (1/4)
Operating principle
Ultrasonic sensors in the rear bumper
measure the distance between the ve-
hicle and an obstacle.
This measurement is indicated by 1
beeps which become more frequent the
closer you come to the obstacle, until
they become a continuous beep when
the vehicle is approximately 20 to
This function is an addi-
30 centimetres from the obstacle.
tional aid that indicates the
The system detects obstacles to the distance between the vehi-
front, the rear and the sides of the ve- cle and an obstacle whilst
hicle. reversing, using sound signals.
The parking distance control system Under no circumstances should it
is only activated when the vehicle is Special features replace the driver’s care or respon-
driven at a speed below approximately sibility whilst reversing.
6 mph (10 km/h). Ensure that the ultrasonic sensors indi-
cated by arrows 1 are not obscured (by The driver should always be ready
dirt, mud, snow, etc.). for sudden incidents while driv-
ing: always ensure that there are
no small, narrow moving obstacles
(such as a child, animal, pushchair,
bicycle, stone, post etc.) in the blind
spot when manoeuvring.
2.34
PARKING DISTANCE CONTROL (2/4)
2 C
A B
Note: the display 2 shows the vehicle Operation
surroundings and emits beeps.
Most objects located less near the
It is necessary to travel a few metres front, rear and sides of the vehicle are
before the side detection is activated. detected.
If all areas have a grey background, the Depending on the distance of the ob-
whole area around the vehicle is being stacle, the frequency of the beep will
monitored: be higher while approaching it, and will
– A: analysis of the vehicle surround- become a solid beep around 20 cm for
ings in progress; obstacles to the sides, and 30 cm for
obstacles to the front or rear. Green,
– B: analysis of the vehicle surround- orange and red zones will be displayed
ings carried out. on the display C.
2.35
PARKING DISTANCE CONTROL (3/4)
If a side obstacle is detected:
D – the beeps become faster and then
sound continuously as the obstacle
gets nearer. Green, orange and red
zones will be displayed on the dis-
play D;
– if there is no risk of collision, no beep
will sound when approaching the ob-
3 stacle. Green, orange and red zones
will be displayed interspersed on the
display D.
Note: in the event of a change in tra-
jectory during a manoeuvre, the risk of
collision with an obstacles may be sig-
nalled late.
Detection of obstacles to the side
Depending on the direction of the
wheels, the system determines the tra-
jectory of the vehicle and notifies the
driver of any risk or otherwise of a col- An impact to the under-
lision with an obstacle 3 to the side of side of the vehicle while
the vehicle. manoeuvring (e.g.: strik-
ing a post, raised kerb or
other street furniture) may result in
damage to the vehicle (e.g.: defor-
mation of an axle).
To avoid any risk of accident, have
your vehicle checked by an ap-
proved Dealer.
2.36
PARKING DISTANCE CONTROL (4/4)
Operating faults
Depending on the vehicle, when the
system detects an operating fault, the
4 message “Check parking sensor” ap-
5 pears on the instrument panel, accom-
panied by the warning light © and
a beep lasting approximately 5 sec-
onds. Consult an approved dealer
2.37
REVERSING CAMERA (1/2)
2
1
Operation Note: make sure that the reversing Note: depending on the vehicle, cer-
Moving into reverse gear, the 1 camera camera is not obscured (by dirt, mud, tain settings can be adjusted from the 2
(located on the tailgate on five-seater snow, etc.). touchscreen. Refer to the handbook for
versions or near the number plate lights the equipment.
on estate versions) provides a view of
the area behind the vehicle on the 2
touchscreen. Depending on the ve-
hicle, this may be accompanied by a
moving guide line or a static guide line.
This function is an additional aid. It cannot, therefore, under any circum-
stances replace the vigilance or the responsibility of the driver.
The driver should always be ready for sudden incidents while driving:
always ensure that there are no small, narrow moving obstacles (such
as a child, animal, pushchair, bicycle, stone, post etc.) in the blind spot when ma-
noeuvring.
2.38
REVERSING CAMERA (2/2)
3 4
2
C
B
A
2.39
ASSISTED PARKING (1/4)
2.40
ASSISTED PARKING (2/4)
Choice of manoeuvre Operation Your speed should not exceed around
4 mph (7 km/h).
The system can perform four types of Parking
manoeuvres:
– parallel parking;
As long as the vehicle speed is less Once the warning light on the
instrument panel goes off and a beep
than 20 mph (30 km/h), the system
– perpendicular parking; looks for available parking spaces on sounds, the manoeuvre has been com-
both sides of the vehicle. pleted.
– angle parking;
– moving out of a parallel parking Once a space has been found, it is dis-
space. played on the multifunction screen, in-
dicated by a small letter “P”. So that
From the multifunction screen, select the vehicle can detect a space, drive
the manoeuvre to be performed. slowly, with the indicators activated on
Note: when starting the vehicle, or after the same side as the space, until the
having successfully completed parallel message "Stop” is displayed, along
parking using the system, the default with a beep.
manoeuvre proposed by the system is The space is then indicated on the mul-
assistance in exiting a parallel parking tifunction screen by a capital “P”.
space. In other cases, the default ma-
noeuvre can be set from the multifunc- – Stop the vehicle;
tion screen. – select reverse gear.
2.41
ASSISTED PARKING (3/4)
Your speed should not exceed around In this case, the reason for suspending
4 mph (7 km/h). the manoeuvre will be displayed on the
Once in position to exit the space, the multifunction screen.
system will notify you of the end of the Make sure:
manoeuvre. – you have released the steering wheel
1
Once the warning light on the
instrument panel goes off and a beep
and;
– that all doors and the boot are closed,
sounds, the manoeuvre has been com- and;
pleted. – that no obstacles are in the way of
the direction of movement, and;
– that the engine is started.
Suspending the manoeuvre
The manoeuvre is suspended in the fol-
lowing circumstances: Cancelling the manoeuvre
– you take control of the wheel; The manoeuvre can be stopped in the
– a door or the boot is opened; following cases:
Exiting a parallel parking space – the vehicle is at a standstill for too – by pressing the system activation
– Select “Exit parallel parking space” long; switch;
mode; – an obstacle in the direction of move- – the vehicle speed has exceeded
– activate the direction indicator on the ment prevents the manoeuvre from 4 mph (7 km/h);
side you wish to go out of; being completed; – you have performed more than ten
– press and hold switch 1 (around – the engine will stop. forwards/backwards movements in
2 seconds).
Once the warning light on the
one manoeuvre;
– the parking distance control sensors
The indicator light lights up
on the instrument panel and a beep
instrument panel goes off and a beep
sounds, the manoeuvre has been sus-
are dirty or blocked;
– the vehicle wheels have skidded.
pended. To resume the manoeuvre,
sounds;
– release the steering wheel;
– go forwards and backwards using
press and hold the system activation
switch. Once the warning light on the
instrument panel goes off and a beep
the parking distance control system sounds, the manoeuvre has been com-
alerts. pleted.
2.42
ASSISTED PARKING (4/4)
This function is an additional driving aid. This function is not under any circumstances intended to replace the due care
and attention of the driver, who should at all times be in control of the vehicle.
Make sure that the manoeuvre complies with the applicable traffic regulations at your location.
– The driver should always be ready for sudden incidents while driving: always ensure that there are no small, narrow moving
obstacles (such as a child, animal, pushchair, bicycle, stone, post etc.) in the blind spot when manoeuvring.
– The system cannot detect objects located in the sensor blind spots.
– When manoeuvring, the steering wheel may turn quickly: do not put your hands inside, and make sure that nothing is caught
inside.
– Always visually check that the parking space proposed by the system is still available and contains no obstacles.
– The system should only be used when towing a trailer or when there is a towing or load carrying system on the vehicle.
2.43
AUTOMATIC TRANSMISSION (1/3)
2 5 5
3
2.44
AUTOMATIC TRANSMISSION (2/3)
Driving in automatic mode Driving in manual mode Special circumstances
Put lever 1 into position D. With the selector lever in position D, – If the bends and road surface do
move the lever to the left into the M po- not allow you to stay in automatic
In most road conditions you will en- sition. Shifting the lever or the paddles
counter, you will not need to touch your mode (e.g. in the mountains), we
repeatedly allows you to change gears recommend that you change to
lever again: the gears will change au- manually:
tomatically at the right time and at the manual mode. This will prevent the
– to move down through the gears, automatic gearbox from changing
most suitable engine speed because push the lever forwards or press the
the automatic system takes into ac- gear repeatedly when climbing, and
left-hand paddle; permit engine braking on long de-
count the vehicle load and road contour – to move up through the gears, push
and adjusts itself to the particular driv- scents.
the lever backwards or press the
ing style you have chosen. right-hand paddle.
The gear selected is displayed on the
Economical driving instrument panel.
When driving, always leave the lever
in position D, keeping the accelerator
pedal lightly depressed to ensure auto-
Special cases
In certain driving conditions (for exam-
matic gear changes at a lower engine
ple, engine protection, operation of the
speed.
Electronic Stability Programme: the au-
Accelerating and overtaking tomatic system may change gear auto-
matically. Likewise, to prevent incorrect
Depress the accelerator pedal firmly manoeuvres, a gear change may be re-
and fully (so that it goes beyond the fused by the automatic system: in this
kickdown point). case the gear display flashes for a few
This will enable you to change down seconds as a warning.
to the optimum gear within the
engine range.
2.45
AUTOMATIC TRANSMISSION (3/3)
Parking the vehicle Operating faults
When the vehicle is stopped, move the 7
– when driving, if the “CHECK AUTO
lever to position P while keeping your GEARBOX ” message appears on
foot on the brake pedal: the gearbox is the instrument panel, it indicates a
in neutral and the drive wheels are me- fault.
chanically locked by the driveshaft. 6
Apply the handbrake. Contact your approved Dealer as
soon as possible;
– when driving, if the message
“Gearbox overheating” appears on
the instrument panel, stop as soon
as possible to let the gearbox cool
down and wait for the message to
disappear;
– If a vehicle with an automatic
gearbox breaks down, refer to the When setting off, if the lever is locked
information on “Towing” in Section 5. in position P even though you are press-
ing the brake pedal, the lever can be re-
leased manually. To do this, release the
base of the lever, then use a tool (rigid
An impact to the under- rod) in the slot 6 and simultaneously
side of the vehicle while press button 7 to unlock the lever.
manoeuvring (e.g.: strik-
ing a post, raised kerb or Contact an authorised dealer as soon
other street furniture) may result in as possible.
damage to the vehicle (e.g.: defor-
mation of an axle).
To avoid any risk of accident, have
your vehicle checked by an ap- For safety reasons, do not
proved Dealer. switch off the ignition before
the vehicle has come to a
complete standstill.
2.46
Section 3: Your comfort
7 8 7
3.2
AIR VENTS, air outlets (2/2)
To remove bad odours from your ve-
hicles, only use the systems designed
for this purpose. Consult an approved
Dealer.
11 12
9
10
3.3
MANUAL AIR CONDITIONING (1/3)
1 2 3 4 The air conditioning system is used
for:
– lowering the temperature inside the
passenger compartment;
– eliminating condensation more
quickly.
6 5
The controls Switching air conditioning on
1 Adjusting the air temperature. or off
(depending on vehicle)
2 Adjusting the ventilation speed.
The air conditioning is switched on (in-
3 Air conditioning. dicator light on) or off (indicator light off)
4 Distribution of air in the passenger using button 3.
compartment. Activation is not possible if control 2 is
5 De-icing/demisting of the rear screen set to OFF.
and, depending on the vehicle, the
door mirrors.
6 Air recirculation.
3.4
MANUAL AIR CONDITIONING (2/3)
Distribution of air in the 1 2 3 4
passenger compartment
There are five air distribution options.
Turn control 4 to choose the distribution
option.
The air flow is directed to the
W windscreen and the front side
window demisting vents.
The air flow is distributed be-
i tween all the air vents, the
front side window demisting vents, the
windscreen demisting vents and the
footwells.
The air flow is directed mainly 6 5
ó towards the footwells.
Switching the air Air recirculation is for:
The air flow is directed towards recirculation on – isolating the vehicle from the exter-
G the dashboard air vents, the
front footwells and, depending on the
Press button 6: the integrated indicator nal atmosphere (driving in polluted
areas, etc.);
light comes on. In these conditions, air
vehicle, the second row footwells. is taken from the passenger compart- – lowering the passenger compart-
ment and is recycled, with no air being ment temperature as quickly as pos-
All the air flow is directed to the
J dashboard vents. taken from outside the vehicle. sible.
Prolonged use of air recirculation can lead to condensation forming on the side
windows and windscreen, and discomfort due to the use of non-renewed air in
the passenger compartment. We therefore advise you to return to normal mode
(external air) as soon as the air recirculation function is no longer required, by
pressing the button 6 again.
3.5
MANUAL AIR CONDITIONING (3/3)
1 4 2 3 4 Adjusting the air temperature
Turn control 1 to obtain the desired
temperature. The further towards the
red the slide is, the higher the tempera-
ture will be.
When the air conditioning system is
used for long periods, it may begin to
feel cold. To increase the temperature,
turn control 1 to the right.
3.6
AUTOMATIC CLIMATE CONTROL (1/4)
1 2 3 4 5 Varying the ventilation speed
In automatic mode, the system uses
the most suitable amount of air to reach
and maintain the desired comfort level.
You can still adjust the ventilation
speed by turning control 6 to increase
or reduce the ventilation speed.
3.7
AUTOMATIC CLIMATE CONTROL (2/4)
Clear View function 1 3 4
Press button 3 – the integrated indica-
tor light comes on.
This function quickly demists and de-
ices the windscreen, the rear screen,
the front side windows, and the door
mirrors (depending on the vehicle). The
air conditioning and rear screen de-ic-
ing functions must be activated.
Press button 8 to stop the heated rear
screen operating, and the integrated in-
dicator goes out.
To exit this function, press button 3
or 1. 8
Adjusting the distribution The air flow is distributed be-
of air in the passenger
Ø tween all the air vents, the
front side window demisting air vents
compartment and the windscreen demisting vents.
Press one of the buttons 4. The in-
The air flow is mainly directed
tegrated warning light in the button
comes on.
½ to the dashboard air vents.
The air flow is directed mainly
It is possible to combine two positions
simultaneously – press both buttons 4.
¿ towards the footwells.
3.8
AUTOMATIC CLIMATE CONTROL (3/4)
5
8
Rear screen de-icing/ Switching air conditioning on
demisting or off
Press button 8 – the integrated indica- In automatic mode, the system switches
tor light comes on. This function en- the air conditioning system on or off,
ables rapid demisting or de-icing of the depending on the climate conditions.
rear screen and de-icing of the door Press button 5 to switch off the air
mirrors (on equipped vehicles). conditioning; the integrated indicator
To exit this function, press button 8 comes on.
again. Demisting automatically stops.
Vehicles fitted with the ECO
mode (button 9): Once activated,
the ECO mode may reduce the ef-
fective performance of the air condi-
tioning. Please refer to the informa-
tion on “Driving advice, Eco-driving”
in Section 2.
3.9
AUTOMATIC CLIMATE CONTROL (4/4)
1 Stopping the system
Turn control 6 to “OFF” to stop the
system. To start, turn control 6 again
to adjust the blower speed or press
button 1.
7 6
Air recirculation (isolation of Manual use
the passenger compartment) Press button 7 – the integrated indica-
tor light comes on.
K Prolonged use of this position may lead
This function is managed automatically to odours, caused by non-renewal of
(operation is confirmed by a warning air, and the formation of condensation
light on button 7), but you can also acti- on the windows.
vate it manually.
We therefore advise you to return to au-
The system determines whether or not tomatic mode as soon as air recircula-
the air recycling function is used, based tion is no longer needed, by pressing
on the quality of the outside air. button 7.
To exit this function, press button 7
again.
3.10
AIR CONDITIONING: information and operating instructions (1/2)
Advice on use Fuel consumption Operating faults
In some situations (air conditioning off, You will normally notice an increase in As a general rule, contact your ap-
air recirculation activated, ventilation fuel consumption (especially in town) proved dealer in the event of an oper-
speed at zero or low etc.), you may when the air conditioning is operating. ating fault.
notice that condensation starts to form For vehicles fitted with air conditioning – Reduction in de-icing, demisting
on the windows and windscreen. with no automatic mode, switch off the or air conditioning performance.
If there is condensation, use the “Clear system when it is not required. This may be caused by the passen-
View” function to remove it, then use Advice for reducing consumption ger compartment filter cartridge be-
the air conditioning in automatic mode and helping to preserve the environ- coming clogged.
to stop it forming again. ment – No cold air is being produced.
Drive with the air vents open and the Check that the controls are set cor-
windows closed. rectly and that the fuses are sound.
If the vehicle has been parked in the Otherwise, switch off the system.
sun, open the doors for a few moments
to let the hot air escape before starting
the engine. Presence of water under the
vehicle
Vehicles equipped with ECO
mode: once activated, ECO mode
Maintenance After prolonged use of the air condi-
Refer to the Maintenance Document tioning system, it is normal for water
may reduce the performance of the
for your vehicle for the inspection fre- to be present under the vehicle. This is
air conditioning. Please refer to the
quency. caused by condensation.
information on “Driving advice, Eco-
driving” in Section 2.
3.11
AIR CONDITIONING: information and operating instructions (2/2)
Type of refrigerant fluid
A A A Ñ
Type of oil in the air condi-
tioning circuit
Inflammable product
Consult the driver’s hand-
book
Maintenance
Quantity of refrigerant
x.xxx kg fluid present in the ve-
The refrigerant circuit may contain hicle.
fluorinated greenhouse gases.
Depending on the vehicle, you will find Global Wa r m i n g
the following information on label A af- GWP xxxxx Potential (CO2 equi-
Do not open the refriger-
fixed inside the engine compartment. valent).
ant circuit. The fluid may
The presence and location of the infor- damage eyes or skin.
mation on label A depends on the ve- CO2 eq Quantity in weight and
hicle. x.xx t in CO2 equivalent.
3.12
ELECTRIC WINDOWS (1/2)
These systems operate with the igni-
tion on or off, until one of the front doors
is opened (limited to about 3 minutes).
1 6
5
2
Driver’s responsibility
Never leave your vehicle 4 3
with the RENAULT card or
key inside, and never leave
a child, adult who is not self-suffi-
cient or a pet, even for a short while.
They may pose a risk to themselves Electric windows
or to others by starting the engine Press or pull the switch to raise or lower Avoid resting any objects against
or activating equipment (such as the a window to the desired height (the rear a half-open window: there is a risk
gear lever or electric windows). windows do not open fully); that the electric window could be
If any part of the body becomes damaged.
From the driver’s seat, use switch:
trapped, reverse the direction of the 1 for the driver’s side;
window immediately by pressing the 2 for the front passenger side;
relevant switch. 3 and 5 for the rear passenger win- Passenger safety
Risk of serious injury. dows. The driver can prevent the
From the passenger seats, use front and rear passenger
switch 6. electric windows from op-
erating (and the driver’s window)
by pressing switch 4. A confirmation
message is displayed on the instru-
ment panel.
3.13
ELECTRIC WINDOWS (2/2)
One-touch mode Operating faults
Depending on the vehicle, this mode In case of a fault when closing a window,
works in addition to the operation of the the system reverts to normal mode:
electric windows described previously. pull the switch concerned up as often 7
It is only fitted to the driver’s window. as necessary to fully close the window
Briefly press or pull switch 1 fully: the (the window will close gradually), hold
window is fully lowered or raised. the switch (still on the closure side) for
Pressing the switch again stops the one second then lower and raise the
window moving. window fully to reinitialise the system.
Note: If the driver’s window detects re- If necessary, contact your authorised
sistance when closing (e.g. tree branch, dealer.
etc.), it stops and then lowers again by
a few centimetres.
3.14
FIXED SUNROOF/SUN VISOR
2 4
3.15
INTERIOR LIGHTING
2 5
1 3
3.16
PASSENGER COMPARTMENT STORAGE, FITTINGS (1/4)
Front door storage pockets 1 Sun visor storage 2 Centre console storage
They can hold a 1.5 litre bottle. This can be used for storing motorway compartment 3
tickets, cards, etc.
3.17
PASSENGER COMPARTMENT STORAGE, FITTINGS (2/4)
4
6
7
8
5
3.18
PASSENGER COMPARTMENT STORAGE, FITTINGS (3/4)
10
3.19
PASSENGER COMPARTMENT STORAGE, FITTINGS (4/4)
12
11
3.20
ASHTRAY, CIGARETTE LIGHTER, ACCESSORIES SOCKET
Accessories socket 1
1
It is provided for connecting accessories
approved by our Technical Department.
2 3
3.21
REAR HEAD RESTS
3.22
REAR BENCH SEAT: functions
To replace the seatback, proceed in
the reverse order to removal.
Refit the seatback and click it back into
place.
1
A
When moving the rear
seats, ensure that nothing
obstructs the anchorage
To fold down the seatback points (passenger’s arm or
leg, a pet, gravel, cloth, toys, etc.).
Ensure that the front seats are far
enough forward.
Lower the headrests fully.
For safety reasons, carry
Place the seat belts in their guides A.
out any adjustments when When refitting the seat-
Press button 1 and lower the seat- the vehicle is not being back, make sure it is cor-
back B. driven. rectly locked in place.
The configuration of the two-seat If seat covers are fitted,
bench with the small seatback B make sure these do not prevent the
pulled down, does not allow the seatback latch from locking in.
central seat to be used as it would Make sure that the seat belts are
be impossible to buckle the seat belt positioned correctly.
(belt buckles inaccessible). Reposition the headrests.
Before moving the seatback, put
the seat belt in belt guide A to avoid
damaging it.
3.23
BOOT
1 3
Lower the tailgate using the handles 2 – access the luggage compartment by
inside the tailgate to help you. tilting the rear bench seatback(s),
– insert a pencil or similar object in
recess 3 and slide the unit as shown The attaching of any carry-
in the illustration; ing device (bike rack, lug-
– push the tailgate to open it. gage box etc.) resting on
the luggage compartment
lid is prohibited. To install a carrying
device on your vehicle, contact an
Approved Dealer.
3.24
REAR PARCEL SHELF
1 B 3
A
A
2 2
3.25
LUGGAGE COMPARTMENT COVER: estate version
1 A
B
1
2
1
Do not place any heavy or solid objects on the luggage cover. These may pose a risk to the vehicle occupants if the
driver has to brake suddenly or if the vehicle is involved in an accident.
3.26
BOOT ARRANGEMENTS
3 6
4
5
2
Bag hooks 4
Maximum weight per hook: 5 kg.
3.27
TRANSPORTING OBJECTS IN THE LUGGAGE COMPARTMENT
Always position the objects transported
so that the largest surface is against:
3.28
TRANSPORTING OBJECTS towbar
3.29
TRANSPORTING OBJECTS: Luggage net (1/2)
2
A
Luggage net A Fitting the luggage net – to access the lower net ring 2 the
behind the front seats first time you use it, please contact
On equipped vehicles, this can be used an authorised dealer;
when transporting animals or luggage, Inside the vehicle on each side:
to separate them from the passenger – once you have accessed the lower
section. – lift the cover 1 to access the upper ring attachment, attach the hook of
mounting ring of the net; the net strap to the ring 2;
It can be positioned:
– fix the net strap hook onto the ring; – adjust the net strap so that it is taut.
– behind the front seats;
– behind the rear bench seat.
3.30
TRANSPORTING OBJECTS: Luggage net (2/2)
4
C
6 7
5 B
3.31
ROOF BARS/SPOILER
Precautions during use
Handling the tailgate A
Before handling the tailgate, check the
1 objects and/or accessories (bike rack,
roof box, etc.) fitted to the roof bars:
these must be correctly positioned and
secured, so as not to hinder the opera-
tion of the tailgate.
3.32
MULTIMEDIA EQUIPMENT
The presence and location of this equip-
ment depends on the vehicle version. 1
1 Multimedia touchscreen;
2 Multimedia sockets;
3 Steering column control;
4 Voice commands;
5 Microphone.
4
5
2
3.33
3.34
Section 4: Maintenance
Bonnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.2
Engine oil level: general information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.4
Engine oil level: topping up/filling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.5
Oil change . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.6
Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.7
engine coolant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.7
brake fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.8
windscreen washer reservoir . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.9
Filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.9
Tyre pressure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.10
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.12
Bodywork maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.13
Interior trim maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.16
4.1
BONNET (1/2)
1
Please note when work-
ing close to the engine that
To open the bonnet, pull the handle 1. Unlocking the bonnet catch it may be hot. The engine
To open, push tab 2 to the left as you cooling fan may also start
open the bonnet.
at any moment. The warning
light in the engine compartment re-
Opening the bonnet minds you of this.
Lift the bonnet; you will need to guide it
Risk of injury.
as it is held by a strut.
4.2
BONNET (2/2)
Closing the bonnet
Check that nothing has been left in the
engine compartment.
To close the bonnet again, hold the
bonnet in the middle and lower it to
30 cm above the closed position, then
release it. It will latch automatically
under its own weight.
4.3
ENGINE OIL LEVEL: general information
It is normal for an engine to use oil for – remove the dipstick and wipe with a
lubrication and cooling of moving parts
B clean, lint-free cloth;
and it is normal to top up the level be- A – push the dipstick in as far as it will
tween oil changes. go (for vehicles equipped with a cap-
However, contact your approved type dipstick C, screw the cap in as
Dealer if more than 0.5 litres is being far as it will go);
consumed every 600 miles (1,000 km) – take out the dipstick again;
after the running in period. C – read the level: it should never fall
Oil change frequency: check the oil B below minimum mark A or exceed
level from time to time and certainly maximum mark B.
before any long journey to avoid the Once the operation has been com-
risk of damaging your engine. A pleted, ensure that the dipstick is
pushed in as far as it will go or that
the “cap-type dipstick” is completely
screwed in.
4.4
ENGINE OIL LEVEL: topping up/filling (1/2)
1 1
2 1
2
4.5
ENGINE OIL LEVEL: topping up, filling (2/2) OIL CHANGE
4.6
LEVELS (1/3)
Frequency of checking coolant level Replacement interval
Check the coolant level regularly Refer to the Maintenance Document for
(very severe damage is likely to be your vehicle.
1 caused to the engine if it runs out of
coolant).
If the level needs to be topped up, only
use products approved by our Technical
Department which ensure:
– protection against freezing;
– an anti-corrosion protection for the
cooling system.
Coolant level
With the engine switched off and on
level ground, the level when cold must
be between the MINI and MAXI marks
on reservoir 1.
Consult your approved dealer at
Top this level up when cold before it once if you notice an abnormal or
reaches the MINI mark. repeated drop in any of the fluid
levels.
4.7
LEVELS (2/3)
Level 2
It is normal for the level to drop as the
brake shoes become worn, but it must
never drop lower than the “MINI" warn-
ing line.
If you wish to check the disc and drum
wear yourself, you should obtain the
document explaining the checking pro-
2 cedure from the manufacturer’s net-
work or web site.
Topping up
After any operation on the hydraulic cir-
cuit, a specialist must replace the brake
fluid.
Brake fluid level Only use fluids approved by our
The level should be read with the engine Technical Department (and taken from
switched off and on level ground. a sealed container).
This should be checked frequently, Replacement interval
and immediately if you notice even the
slightest loss in braking efficiency. Refer to the Maintenance Document for
your vehicle.
Please note when work-
ing close to the engine that
it may be hot. The engine
cooling fan may also start
at any moment. The warning
light in the engine compartment re-
minds you of this.
Consult your approved dealer at
once if you notice an abnormal or Risk of injury.
repeated drop in any of the fluid
levels.
4.8
LEVELS (3/3)/FILTERS
Filters
The replacement of filter components
(air filter, cabin filter, diesel filter, etc.)
is scheduled in the maintenance opera-
tions for your vehicle.
Replacement intervals for filter el-
ements: refer to the Maintenance
Document for your vehicle.
3
4.9
TYRE PRESSURE (1/2)
Vehicle fitted with a tyre pressure
A loss warning system
If under-inflated (puncture, low pres- A
sure etc.), the warning light on
the instrument panel comes on. See
“Tyre pressure loss warning” in B
Section 2.
C E F
C E F
D E F
G
4.10
TYRE PRESSURE (2/2)
Tyre safety and use of snow chains:
Special note concern- Refer to the information on “Tyres” in
ing fully laden vehicles Section 5 for the servicing conditions
(Maximum Permissible and, depending on the version, the use
All-Up Weight) and towing of chains.
a trailer: the maximum speed must
For your safety, please re-
be limited to 60 mph (100 kph) and
spect the speed limit.
the tyre pressure increased by
0.2 bar. When they need to be re-
placed, only tyres of the
Please refer to the information on
same make, size, type and profile
“Weights” in Section 6.
should be used on a single axle.
Risk of tyre blowouts.
They must: either have a load ca-
pacity and speed rating at least
equal to those of the original
tyres, or conform to those recom-
mended by an authorised dealer.
Failure to heed these instructions
could endanger your safety and
affect your vehicle’s roadworthi-
ness.
Risk of loss of control of the ve-
hicle.
4.11
BATTERY
Replacing the battery A 2 3 4
As this operation is complex, we advise
you to contact an approved Dealer.
2
Before performing any 7 6 5
Battery 1 does not require any mainte- action in the engine com- Label A
nance. You should not open it or add partment, the ignition must Observe the indications on the battery:
any fluid. be switched off (please see – 2 naked flames and smoking are for-
the information on "Starting, stop- bidden;
ping the engine" in Section 2). – 3 eye protection required;
Handle the battery with care – 4 keep away from children;
as it contains sulphuric acid, – 5 explosive materials;
which must not come into – 6 refer to the handbook;
contact with eyes or skin. If Please note when work- – 7 corrosive materials.
it does, wash the affected area with ing close to the engine that
plenty of cold water. If necessary, it may be hot. The engine
consult a doctor. cooling fan may also start
Ensure that naked flames, red hot
objects and sparks do not come into
at any moment. The warning
light in the engine compartment re- The battery is a specific
contact with the battery as there is a minds you of this. type, please ensure it is
risk of explosion. Risk of injury. replaced with the same
type. Consult an approved
dealer.
4.12
BODYWORK MAINTENANCE (1/3)
A well-maintained vehicle will last You should Respect local regulations about wash-
longer. It is therefore recommended to ing vehicles (e.g. do not wash your ve-
maintain the exterior of the vehicle reg- Wash your car frequently, with the hicle on a public highway).
ularly. engine off, with cleaning products rec-
ommended by the manufacturer (never Observe the vehicle stopping distances
Your vehicle has been treated with very use abrasive products). Rinse thor- when driving on gravelled surfaces to
effective anti-corrosion products. It is oughly beforehand with a jet: prevent paint damage.
nevertheless subject to various outside – spots of tree resin and industrial Repair, or have repaired quickly, areas
influences. grime; where the paint has been damaged, to
– mud in the wheel arches and under- prevent corrosion spreading.
Corrosive agents in the atmosphere neath the body which forms damp
– atmospheric pollution (built-up and patches; Remember to visit the body shop pe-
industrial areas); – bird droppings, which cause a riodically in order to maintain your
– saline atmospheres (near the sea, chemical reaction with the paint that anti-corrosion warranty. Refer to the
particularly in hot weather); rapidly discolours paintwork and Maintenance Document.
– seasonal and damp weather condi- may even cause the paint to peel If it is necessary to clean mechani-
tions (e.g. road salt in winter, water off; cal components, hinges, etc., spray
from road cleaners, etc.). wash the vehicle immediately to them with products approved by our
remove these marks since it is im- Technical Department to protect them
Minor impacts possible to remove them by polish- after they have been cleaned.
Abrasive action ing;
Dust and sand in the air, mud, road grit – salt, particularly in the wheel arches
thrown up by other vehicles, etc. and underneath the body after driv-
ing in areas where the roads have
You should take a number of minor pre- been gritted.
cautions in order to safeguard your ve-
hicle against such risks. Remove any plant matter (resin, leaves,
etc.) from the vehicle regularly.
4.13
BODYWORK MAINTENANCE (2/3)
What you should not do
Wash the vehicle in bright sunlight or
freezing temperatures. Degrease or clean using
high-pressure cleaning
Do not scrape off mud or dirt without equipment or by spray-
pre-wetting. ing on products not ap-
Allow dirt to accumulate on the exterior. proved by our Technical
Allow rust to form following minor im- Department:
pacts. – mechanical components (e.g.:
engine compartment);
Do not use solvents not approved by – underbody;
our Technical Department to remove – parts with hinges (e.g.: inside the
stains as this could damage the paint- doors);
work. – painted plastic external fittings (e.g.:
Do not drive in snow or muddy condi- bumpers).
tions without washing the vehicle, par- Doing this could give rise to corrosion
ticularly under the wheel arches and or operational faults.
body.
4.14
BODYWORK MAINTENANCE (3/3)
Vehicles with a matte paint Using a roller type car wash Cleaning the headlights
finish Return the windscreen wiper stalk to As the headlights are made of plastic
This type of paint requires certain pre- the Park position (refer to the informa- “glass”, use a soft cloth or cotton wool
cautions. tion on the “Windscreen washer, wiper” to clean them. If this does not clean
in Section 1). Check the mounting of them properly, moisten the cloth with
You should do the following external accessories, additional lights soapy water, then wipe clean with a soft
and mirrors, and ensure that the wiper damp cloth or cotton wool.
Wash the vehicle by hand using plenty
blades are secured with adhesive tape. Finally, carefully dry off with a soft dry
of water, using a soft cloth or a gentle
Remove the radio aerial mast if your cloth.
sponge.
vehicle is fitted with this equipment. Do not use cleaning products con-
Do not do the following taining alcohol or utensils (e.g.: a
Remember to remove the tape and refit
Use wax-based products (polishing). the antenna after washing. scraper).
Rub too hard.
Wash the vehicle in a roller-type car
wash.
Attach stickers to the paintwork (risk of
leaving marks).
4.15
INTERIOR TRIM MAINTENANCE (1/2)
A well-maintained vehicle will last Glass instrument panel Textiles (seats, door trim, etc)
longer. It is therefore recommended to (e.g. instrument panel, clock, exterior
maintain the interior of the vehicle regu- Vacuum-clean the textiles regularly.
temperature display, radio display, etc.)
larly. Liquid stain
Use a soft cloth (or cotton wool).
A stain should always be dealt with If this does not clean them properly, Use soapy water.
swiftly. use a soft cloth (or cotton wool) slightly
moistened with soapy water and then Dab lightly (never rub) with a soft cloth,
Whatever type of stain is on the trim, rinse and remove the excess.
use cold (or warm) soapy water with wipe clean with another soft damp cloth
natural soap. or cotton wool.
Finally, carefully dry off with a soft dry Solid or pasty stain
Detergents (washing-up liquid, pow- cloth. Carefully remove the excess solid or
dered products, alcohol-based prod- pasty material immediately with a
ucts) should not be used. Do not use products containing alco-
hol and/or spray fluids on the area. spatula (working from the edges to the
Use a soft cloth. centre to avoid spreading the stain).
Clean as for a liquid stain.
Rinse and soak up the excess.
Seat belts
Special instructions for sweets or
These must be kept clean. chewing gum
Use products selected by our Technical
Department (Approved outlets) or Put an ice cube on the stain to solidify
warm, soapy water and a sponge and it, then proceed as for a solid stain.
wipe with a dry cloth.
Detergents or dyes must not be used
under any circumstances.
4.16
INTERIOR TRIM MAINTENANCE (2/2)
Removal/replacing removable You should not:
equipment originally fitted in Position objects such as deodorants,
the vehicle scents etc. near air vents as this could
If you need to remove equipment in damage your dashboard trim.
order to clean the passenger com-
partment (for example, mats), always
ensure that they are correctly refitted
and are the right way around (the driv-
er’s mat should be fitted on the driver’s Use high-pressure
side, etc.) and fit them with the compo- cleaning equipment or
nents supplied with the equipment (for sprays inside the pas-
example, the driver mat should always senger compartment:
be fixed using the pre-fitted mounting
components). without careful use, this equipment
could impair the correct functioning
With the vehicle stationary, always of the electrical or electronic compo-
ensure that nothing will impede driving nents in the vehicle, or have other
(anything obstructing the pedals, heel detrimental effects.
wedged by the mat etc.).
4.17
4.18
Section 5: Practical advice
5.2
PUNCTURE, EMERGENCY SPARE WHEEL (2/4)
3
6
7
4 5
A
2
1
Emergency spare wheel – unscrew nut 4 in an anti-clockwise – pull the wheel towards you;
direction until it comes off com- – lay the wheel down flat and unfasten
– Open the tailgate; pletely, then place the palm of your
– lift the carpet; cable 6 from its housing 7.
hand on section A of handle 5 and
– lift the cover 1 and remove it; push towards the front of the vehicle. You may remove the wheel from its
– remove the tool kit by lifting it by its The wheel will be lowered; support.
handles;
5.3
PUNCTURE, EMERGENCY SPARE WHEEL (3/4)
6
7
5
8
To refit a wheel To carry out this operation, the cable After changing a wheel, position the
must be unwound. replaced wheel on support 8, with the
If the cable has been wound back up on valve facing the ground. Clip cable 6
its own, unwind it again as follows: in its housing 7, then push the wheel
A wheel size larger than 15” cannot under the boot.
be installed under the vehicle. – pull the handle to unwind the cable;
Ensure that tab 9 is positioned towards
– press the button located under the rear of the vehicle.
handle 5 to hold the unwound cable,
then guide it down; Position yourself behind the vehicle and
pull handle 5 to raise the wheel until it is
– recover the cable from underneath anchored under the vehicle.
the vehicle.
You may refit the wheel.
Make sure that no-one has their fingers close to the cable when you
move the handle: risk of injury.
5.4
PUNCTURE, EMERGENCY SPARE WHEEL (4/4)
4 5
1
For vehicles fitted with this, take
care not to damage the subwoofer 3
To lock the system Note: If the tool kit does not lock in when you replace the tool kit and
place, check the tightness of nut 4 and the cover 1. If not, this could impair
– Press nut 4, screwing it on fully until the correct positioning of handle 5. the correct functioning of the sub-
it locks in place. Several turns will woofer.
be necessary. This operation is es-
sential to ensure that the wheel is Special features
secure;
The emergency spare wheel holder
– return handle 5 to its original posi- should always be present when you are The system should only be
tion; driving even when the wheel itself is not used with the original ve-
– clip the tool kit; present: risk of water entering the ve- hicle wheels or identical
hicle. wheels.
– replace the cover 1 then lower it and
replace the luggage compartment If you have to release it when it is not
carpet. holding a wheel, push the centre of the
wheel holder towards the ground while It is essential to lock the nut
pressing handle 5. so that the wheel is held se-
curely.
5.5
TYRE PRESSURE KIT (1/3)
A tyre which has been punctured Keep the repair kit away from chil-
should always be inspected (and re- dren.
The kit repairs tyres when paired, where possible) as soon as Do not dispose of the empty bottle
tread A has been dam- possible by a specialist. in the countryside. Return it to your
aged by objects smaller When taking a tyre which has been approved dealer or to a recycling or-
than 4 mm. It cannot repair repaired using this kit to be replaced, ganisation.
all types of puncture, such as cuts you must inform the specialist. The bottle has a limited service
larger than 4 mm, or cuts in tyre life which is indicated on its label.
When driving, vibration may be felt
sidewall B. Check the expiry date.
due to the presence of the repair
Ensure also that the wheel rim is in product injected into the tyre. Contact an approved dealer to re-
good condition. place the inflation tube and repair
Do not pull out the foreign body product bottle.
causing the puncture if it is still in
the tyre.
5.6
TYRE PRESSURE KIT (2/3)
With the engine running and the
parking brake applied,
– Disconnect any accessories previ-
ously connected to the vehicle’s ac-
cessories sockets;
– Refer to the information on the in-
flation kit compressor located in the
vehicle’s luggage compartment and
follow the instructions;
– inflate the tyre to the recommended
pressure (please refer to the infor-
2 mation in the section on “Tyre pres-
1 sures”); Before using this kit, park
– after a maximum of 15 minutes, stop the vehicle at a sufficient
inflating and read the pressure (on distance from traffic, switch
the pressure gauge 1); on the hazard warning
Depending on the vehicle, in the event Note: while the bottle is emptying lights, apply the handbrake, ask all
of a puncture, use the kit located in the (approximately 30 seconds), the passengers to leave the vehicle and
boot or underneath the luggage com- pressure gauge 1 will indicate briefly keep them away from traffic.
partment carpet. a pressure of 6 bar, then the pres-
Vehicle fitted with a tyre pressure sure drops.
loss warning system – Adjust the pressure: to increase
If under-inflated (puncture, low pres- it, continue inflation with the kit. To
reduce it, press the button 2. If the vehicle is parked on
sure, etc.), the warning light
lights up on the instrument panel.
the hard shoulder, you must
warn other road users of
See “Tyre pressure loss warning” in your vehicle’s presence
Section 2. with a warning triangle or with other
devices as per the legislation apply-
ing to the country you are in.
5.7
TYRE PRESSURE KIT (3/3)
Once the tyre is correctly inflated, Precautions when using the
remove the kit: slowly unscrew the in- kit
flation end piece 3 to prevent any prod-
3 uct spatter and store the container in The kit should not be operated for more
plastic packaging to prevent product than 15 consecutive minutes.
leaks.
Please be aware that a
– Affix the driving recommendation poorly tightened or miss-
label to the dashboard where it can ing valve cap can make the
easily be seen by the driver; tyres less airtight and may
– Put the kit away. lead to pressure loss.
– At the end of this initial inflation op-
eration, air will still escape from the Always use valve caps identical to
tyre. You must drive a short distance those fitted originally and tighten
in order to seal the hole. them fully.
– Start immediately and drive at
between 12 and 40 mph (20 and
If a minimum pressure of 1.8 bar is 60 km/h) in order to distribute the
not reached after 15 minutes, repair product evenly in the tyre and, after
is not possible; do not drive the ve- driving for 2 miles (3 km), stop and
hicle but contact an approved dealer. check the pressure. Following repair with the kit,
– If the pressure is greater than do not travel further than
1.3 bar but less than the recom- 120 miles (200 km). In addi-
mended pressure (refer to the label tion, reduce your speed and
affixed to the edge of the driver’s under no circumstances exceed
door), readjust it. Otherwise, please 48 mph (80 km/h). The sticker,
contact an authorised dealer: the which you must affix in a prominent
Nothing should be placed tyre cannot be repaired. position on the dashboard, reminds
around the driver’s feet you of this.
as such objects may slide Depending on the country or local
under the pedals during legislation, a tyre repaired with the
sudden braking manoeuvres and inflation kit may need to be replaced.
obstruct their use.
5.8
TOOLS
2 Jack 2
Fold it correctly before refitting it in its
1 housing (ensure that the wheelbrace is
correctly positioned).
Hubcap tool 3
This tool is used to remove the wheel
6 trims.
A 3
Do not leave the tools unsecured inside the vehicle as they may come loose under braking. After use, check that all
the tools are correctly clipped into the tool kit, then position it correctly in its housing: risk of injury.
If bolts are supplied with the emergency spare wheel, you must use these bolts only for the emergency spare wheel.
The jack is designed for wheel changing purposes only. Under no circumstances should it be used for carrying out re-
pairs underneath the vehicle or to gain access to the underside of the vehicle.
5.9
WHEEL TRIMS - WHEEL
1
A
2
C
B
5.10
CHANGING A WHEEL (1/2)
Vehicles equipped with a jack Continue to crank the jack so that the
and wheelbrace baseplate is correctly positioned (it
1 should be underneath the vehicle and
If necessary, remove the wheel trim. aligned with the jack head).
Use the wheelbrace 1 to slacken off the Turn it a few times to lift the wheel off
wheel bolts. Position it so as to be able the ground.
to push from above.
3
Crank up jack 2 by hand to position the
jack head against the jacking point clos-
2 est to the relevant wheel and marked
by an arrow 3.
5.11
CHANGING A WHEEL (2/2)
Undo the bolts and take off the wheel. Vehicle fitted with a tyre pressure
Fit the emergency spare wheel on the loss warning system
central hub and turn it to locate the If under-inflated (puncture, low pres-
mounting holes in the wheel and the
hub. sure etc.), the warning light
on
the instrument panel comes on. See
Tighten the bolts, checking that the “Tyre pressure loss warning” in
wheel is correctly positioned on its hub. Section 2.
Lower the jack.
With the wheel on the ground, tighten
the bolts fully and have the tightness of
the bolts checked and the emergency
spare wheel pressure checked as soon Do not leave the tools un-
as possible. secured inside the vehicle
as they may come loose
under braking. After use,
check that all the tools are correctly
clipped into the tool kit, then posi-
tion it correctly in its housing: risk of
injury.
If bolts are supplied with the emer-
gency spare wheel, you must use
these bolts only for the emergency
spare wheel.
The jack is designed for wheel
If you have a puncture, re- changing purposes only. Under no
place the wheel as soon as circumstances should it be used for
possible. carrying out repairs underneath the
vehicle or to gain access to the un-
A tyre which has been punc- derside of the vehicle.
tured should always be inspected
(and repaired, where possible) by a
specialist.
5.12
TYRES (1/3)
Tyre and wheel safety When the tyre tread has been worn
The tyres are the only contact between to the level of the warning strips, they
the vehicle and the road, so it is essen- become visible 2: it is then neces-
tial to keep them in good condition. You sary to replace your tyres because the
must comply with the local rules given 2 tread rubber is now only 1.6 mm deep
in the highway code. at most, resulting in poor road hold-
ing on wet roads.
An overloaded vehicle, long journeys
by motorway, particularly in very hot
1 weather, or continual driving on poorly
surfaced minor roads will lead to more
rapid tyre wear and affect safety.
5.13
TYRES (2/3)
Tyre pressures Pressures should be checked when the Vehicle fitted with a tyre pressure
tyres are cold; ignore higher pressures loss warning system
Adhere to the tyre pressures (including which may be reached in hot weather
the emergency spare wheel). The tyre If under-inflated (puncture, low pres-
or following a fast journey.
pressures should be checked at least
once a month and additionally before If tyre pressures cannot be checked sure etc.), the warning light
the instrument panel comes on. See
on
any long journey (refer to the label af- when the tyres are cold, assume an in-
fixed to the edge of the driver’s door). crease of 0.2 to 0.3 bar (or 3 PSI). “Tyre pressure loss warning” in Section
2.
Never deflate a hot tyre.
5.14
TYRES (3/3)
Fitting new tyres Use in winter Snow or Winter tyres
We would recommend that these be
Chains fitted to all four wheels to ensure that
For safety reasons, fitting snow your vehicle retains maximum adhe-
chains to the rear axle is strictly for- sion.
bidden. Warning: These tyres sometimes have
Chains cannot be fitted to tyres which a specific direction of rotation and a
are larger than those originally fitted to maximum speed index which may be
the vehicle. lower than the maximum speed of your
For your safety, please re- vehicle.
spect the speed limit.
Studded tyres
When they need to be re-
placed, only tyres of the This type of equipment may only be
same make, size, type and profile used for a limited period and as laid
should be used on a single axle. down by local legislation. It is neces-
sary to observe the speed specified by
They must: either have a load ca- current legislation.
pacity and a speed capacity at Chains may only be fitted
least equal to the original tyres, to tyres of the same size These tyres must, at a minimum, be
or correspond to those recom- as those originally fitted to fitted to the two front wheels.
mended by your authorised your vehicle.
dealer.
Failure to heed these instructions
could endanger your safety and
affect your vehicle’s roadworthi- 18” wheels cannot be
ness. fitted with chains.
Risk of loss of control of the ve- If you wish to fit snow
hicle. chains, you must use spe-
cial equipment. In all cases, we would recommend
that you contact an approved dealer
Consult an approved dealer who will be able to advise you on
the choice of equipment which is
most suitable for your vehicle.
5.15
FRONT HEADLIGHTS: replacing the bulbs (1/3)
5.16
FRONT HEADLIGHTS: replacing the bulbs (2/3)
Halogen main beam headlight
(depending on vehicle)
To change the bulb:
4 – remove cover C;
– disconnect wiring 6;
– unclip the spring 7 and remove the
bulb.
7
5 Bulb type: H1
It is essential to use anti-U.V. 55W
6 bulbs so as not to damage the plastic
on the headlights.
Do not touch the bulb glass. Hold it
by its base.
To comply with local legislation, or
When the bulb has been changed,
Halogen dipped beam make sure you refit the cover correctly.
as a precaution, you can obtain an
headlight emergency kit containing a set of
(depending on vehicle) spare bulbs and fuses from an ap-
proved dealer.
Remove cover A to access the bulb
holder.
To change the bulb: Any operation on (or modi-
– remove cover B; fication to) the electrical
– disconnect wiring 4; system must be performed
– unclip the spring 5 and remove the by an approved dealer
bulb. since an incorrect connection might
damage the electrical equipment
Bulb type: H7 (harness, components and in partic-
ular the alternator). In addition, your
Dealer has all the parts required for
fitting these units.
5.17
FRONT HEADLIGHTS: replacing the bulbs (3/3)
Additional lights
8 If you wish to fit fog lights to your ve-
hicle, please see an authorised dealer.
5.18
REAR LIGHTS AND SIDE LIGHTS: replacing the bulbs (1/6)
A 2 5
3
6
1
B
4
Five-door version To release the light unit, start by moving Refit the bulb holder and push the unit
the exterior edge away to a suffi- in fully until it locks in place.
Side lights/brake and direction cient extent (movement A) to release Check that the light is properly locked
indicator lights clip 3, then pull the light unit backwards in position.
Open the boot lid and remove screws 1. (movement B).
Tighten screws 1.
Remove the bulb holder by carefully
releasing clips 4, lightly raise the bulb 5 Side light and brake light
holder and then release clip 2. Bulb type: P21/5W.
Change the bulb. 6 Direction indicator lights
Bulb type: PY21W.
5.19
REAR LIGHTS AND SIDE LIGHTS: replacing the bulbs (2/6)
8 9
A
10
5.20
REAR LIGHTS AND SIDE LIGHTS: replacing the bulbs (3/6)
13
11
C
12
Pull the light unit backwards (move- Check that the light is properly locked 14 15
ment C). in position.
Tighten the screw 12 and nut 11.
Clip the cover in place.
14 Side light and brake light
Bulb type: P21/5W.
15 Direction indicator lights
Bulb type: PY21W.
5.21
REAR LIGHTS AND SIDE LIGHTS: replacing the bulbs (4/6)
11
18
17
16
10
Five door and estate versions Unclip cover 17 and remove it. Turn bulb holder 18 fully anticlockwise
and change the bulb.
Fog lights and reversing lights 16 To reassemble, proceed in the reverse
Open the boot lid. order to removal.
When the bulb has been changed,
make sure you refit cover 17 correctly.
Reversing light
Type of bulb: H21W.
Rear fog light
Type of bulb: H21W.
5.22
REAR LIGHTS AND SIDE LIGHTS: replacing the bulbs (5/6)
20 21
22
19
Fog lights 19 and reversing lights 20 Unclip cover 21 and remove it. Turn bulb holder 22 fully anticlockwise
(depending on vehicle) and change the bulb.
Open the boot lid. To reassemble, proceed in the reverse
Note: depending on the vehicle, the re- order to removal.
versing and fog lights are inverted. When the bulb has been changed,
make sure you refit cover 21 correctly.
Reversing light
Type of bulb: H21W.
Rear fog light
Type of bulb: H21W.
5.23
REAR LIGHTS AND SIDE LIGHTS: replacing the bulbs (6/6)
25
23 24 D
26
25
High level brake light 23 Number plate lights 24 Side repeaters with bulbs 26
Consult an approved dealer. – Unclip the light by pressing tab 25; – Unclip the repeater 26 (using a
– remove the light cover to gain access flat-blade screwdriver type tool po-
to the bulb. sitioned at D to tilt the repeater to-
wards the front of the vehicle);
Bulb type: W5W.
– turn the bulb holder a quarter of a
turn and take out the bulb.
Bulb type: WY5W.
5.24
INTERIOR LIGHTING: changing bulbs (1/2)
2
1
Courtesy light Courtesy light fitted with diffusers 2 Luggage compartment light
(depending on vehicle) Consult an approved dealer. Unclip the light 3 by pressing the tab on
Courtesy light fitted with diffusers 1 its left side (using a flat-bladed screw-
driver or similar).
Unclip the lens (using a flat-blade
screwdriver or similar). Remove the bulb concerned.
5.25
INTERIOR LIGHTING: changing bulbs (2/2)
Ambient lighting
Please consult an authorised dealer.
5.26
FUSES (1/5)
1
B
Check the fuse in question and replace it, if necessary, by a fuse of the
same rating.
To comply with current legislation, or
If a fuse is fitted with too high a rating, it may cause the electrical circuit
as a precaution, you can obtain an
to overheat (risk of fire) in the event of an item of equipment using an ex-
emergency kit from your approved
cessive amount of current.
dealer containing a set of spare
bulbs and fuses.
5.27
FUSES (2/5)
Allocation of fuses
(the presence of certain fuse depends on the vehicle equipment level)
1 2 3 36 37 38 39
18
27
19
28
4 11 20 29
5 12 21 30
6 13 22 31
7 14 23 32
8 15 24 33
9 16 25 34
10 17 26 35
5.28
FUSES (3/5)
5.29
FUSES (4/5)
Allocation of fuses
(the presence of certain fuse depends on the vehicle equipment level)
1 2 3 36 37 38 39
18
27
19
28
4 11 20 29
5 12 21 30
6 13 22 31
7 14 23 32
8 15 24 33
9 16 25 34
10 17 26 35
5.30
FUSES (5/5)
5.31
RENAULT CARD: battery
2 A
B
4
1 3
Replacing the battery When refitting, proceed in the reverse Operating faults
When the message “KEYCARD order, then press one of the buttons on If the battery is too weak to ensure cor-
BATTERY LOW” appears on the instru- the card four times, close to the vehicle: rect operation, you can still start (insert
ment panel, replace the RENAULT card the next time the vehicle is started, the the RENAULT card in the card reader)
battery, press button 1 pulling on emer- message will disappear. and lock/unlock the vehicle (refer to the
gency key 2, then unclip the cover 3 Note: it is not advisable to touch the information on "Locking/unlocking the
using tab 4. electronic circuit or contacts on the doors" in Section 1).
Remove the battery by pressing on one RENAULT card when replacing the bat-
side (movement A) and by lifting the tery.
other (movement B) then replace it, en-
suring the polarity and model, shown
on cover 3 are respected.
Check that the cover is clipped shut.
Do not throw away your
used batteries; give them to
an organisation responsible
The batteries are available from approved Dealers, and their service life approxi- for collecting and recycling
mately two years. Check that there is no dye on the battery: risk of an incorrect batteries.
electrical contact.
5.32
BATTERY: breakdown recovery (1/2)
To avoid all risk of sparks: Connecting a battery charger
– Ensure that any electrical consumers The battery charger must be com-
(courtesy lights, etc.) are switched patible with a battery with nominal
off before disconnecting or recon- voltage of 12 volts.
necting the battery. Do not disconnect the battery when the
– When charging, stop the charger engine is running. Follow the instruc-
before connecting or disconnecting tions given by the manufacturer of
the battery. the battery charger you are using.
– Do not place metal objects on the
battery to avoid creating a short cir-
cuit between the terminals.
– Always wait at least one minute after
the engine has been switched off Handle the battery with care
before disconnecting a battery. as it contains sulphuric acid,
which must not come into
– Make sure that you reconnect the contact with eyes or skin. If
battery terminals after refitting. it does, wash the affected area with
plenty of cold water. If necessary,
consult a doctor.
Ensure that naked flames, red hot
Special procedures may be objects and sparks do not come into
required to charge some contact with the battery as there is a
batteries. Contact your ap- risk of explosion.
Before performing any proved dealer. The engine may be hot when car-
action in the engine com-
Avoid all risk of sparks which may rying out operations in close prox-
partment, the ignition must
cause an immediate explosion, and imity. In addition, the engine cooling
be switched off by pressing
charge the battery in a well-venti- fan can come on at any moment.
the engine stop button (please see
the information on “Starting, stop- lated area. Risk of serious injury. Risk of injury.
ping the engine” in Section 2).
5.33
BATTERY: breakdown recovery (2/2)
Starting the vehicle using the
battery from another vehicle 1 2
If you have to use the battery from an-
other vehicle to start, obtain suitable 2
jump leads (with a large cross section) B
from an approved dealer or, if you al-
ready have jump leads, ensure that
they are in perfect condition. A
The two batteries must have an iden- 1
tical nominal voltage of 12 volts. The
battery supplying the current should
4 3
have a capacity (amp-hours, Ah) which
is at least the same as that of the dis-
charged battery.
Ensure that there is no risk of contact Depending on the vehicle, unclip the
between the two vehicles (risk of short battery cover.
circuiting when the positive terminals
are connected) and that the discharged Connect the positive cable A to the
battery is properly connected. Switch support on the (+) terminal 1, then to the
off your vehicle ignition. (+) terminal 4 of the battery supplying
the current.
Start the engine of the vehicle supply-
ing the current and run it at an interme- Connect the negative cable B to the (–)
diate engine speed. terminal 3 of the battery supplying the Check that there is no con-
current and then to the (–) terminal 2 of tact between leads A and B
the discharged battery. and that the positive lead A
is not touching any metal
Start the engine, and as soon as it starts parts on the vehicle supplying the
running, disconnect cables A and B in current.
reverse order ( 2 - 3 - 4 - 1 ).
Risk of injury and/or damage to the
vehicle.
5.34
FITTING A RADIO
5.35
ACCESSORIES
5.36
WINDSCREEN WIPER BLADES (1/2)
To refit
To refit the wiper blade, proceed in re-
verse order to removal. Make sure that
the blade is correctly locked in position.
5.37
WINDSCREEN WIPER BLADES (2/2)
To refit
5 To refit the wiper blade, proceed in re-
verse order to removal. Make sure that
the blade is correctly locked in position.
5.38
TOWING: breakdown recovery (1/2)
Before towing, unlock the steering The speed specified by current legis-
column: with the clutch depressed, lation for towing must always be ob- 2
engage first gear (lever in position N served. If your vehicle is the towing
or R for vehicles with automatic gear- vehicle, do not exceed the maximum
boxes), insert the RENAULT card in the towing weight for your vehicle (refer to
card reader, then press the engine start the information on “Weights” in Section 1
button for two seconds. 6).
Reposition the lever to neutral (posi-
tion N for vehicles fitted with an auto- Towing a vehicle with an
matic gearbox). automatic gearbox
The column is unlocked, the acces- With the engine switched off, the trans-
sory functions are supplied: the vehi- mission is no longer lubricated. It is
cle lights can be used (indicators, brake preferable to tow this type of vehicle on
lights etc.). At night the vehicle must a trailer or tow it with the front wheels
have its lights on. off the ground.
Once you have finished towing, press If the lever is stuck in P, even though
Under exceptional circumstances, you you are depressing the brake pedal, the
the engine start button twice (risk of may tow the vehicle with all four wheels
running down the battery). lever can be released manually. To do
on the ground, only going forward, with this, release the base of the lever, then
the gear lever in the neutral N position, use a tool (rigid rod) in the slot 1 and si-
and for a distance not exceeding multaneously press button 2 to unlock
30 miles (50 km). the lever.
Contact an authorised dealer as soon
as possible.
5.39
TOWING: breakdown recovery (2/2)
5.40
OPERATING FAULTS (1/6)
The following advice will enable you to carry out quick, temporary repairs. For safety reasons you should always contact
an approved Dealer as soon as possible.
The RENAULT card does not lock or Card battery is flat. Replace the battery or have it replaced.
unlock the doors. You can still lock/unlock and start your ve-
hicle (refer to the information on “Locking/
unlocking the doors” in Section 1 and
“Starting/Stopping the engine” in Section
2).
Use of appliances operating on the Stop using the equipment or use the in-
same frequency as the card (mobile tegrated key (refer to the information on
phone, etc.). “Locking, unlocking the opening elements”
in Section 1).
Vehicle located in a high electromag- Use the key integrated in the card (refer to
netic radiation zone. the information on “Locking, unlocking the
Vehicle battery flat. opening elements” in Section 1).
The vehicle is started. With the engine running, the card’s locking/
unlocking device is blocked. Turn off the ig-
nition.
5.41
OPERATING FAULTS (2/6)
The starter is activated POSSIBLE CAUSES WHAT TO DO
The instrument panel indicator lights are Battery terminals not tight, Retighten or reconnect the terminals, or clean them if
weak or fail to light up and the starter battery terminals discon- they are oxidised.
does not turn. nected or oxidised.
Discharged battery or not Connect another battery to the faulty battery. Refer to
operational. information on “Battery: troubleshooting” in Section 5
or replace the battery if necessary.
Do not push the vehicle if the steering column is
locked.
The engine will not start. Starting conditions are not Please refer to the information on “Starting, stopping
fulfilled. the engine” in Section 2.
The RENAULT “hands-free” Insert the card in the card reader in order to start the
card does not work. engine.
Please refer to the information on “Starting, stopping
the engine” in Section 2.
The engine cannot be switched off. Card not detected. Insert the card in card reader.
The steering column remains locked. Steering wheel locked. Move the steering wheel while pressing the engine
start button (please refer to Section 2 “Starting, stop-
ping the engine”).
5.42
OPERATING FAULTS (3/6)
Vibrations. Tyres not inflated to correct pres- Check the tyre pressures: if this is not the
sures, incorrectly balanced or dam- problem, have them checked by an ap-
aged. proved Dealer.
White smoke from the exhaust. In the diesel version, this is necessar- Please refer to the information on “Special
ily a fault. Smoke may be caused by features of diesel versions” in Section 2.
particle filter regeneration.
Smoke under the bonnet. Short-circuit or cooling system leak. Stop, switch off the ignition, stand away
from the vehicle and contact an approved
dealer.
while cornering or braking The level is too low. Top up the engine oil level (refer to the in-
formation on “Engine oil level: topping up,
filling” in Section 4).
is slow to go out or remains lit Loss of oil pressure. Stop the vehicle and contact an approved
under acceleration Dealer.
5.43
OPERATING FAULTS (4/6)
Steering becomes heavy. Assistance overheating. Drive carefully at reduced speed, be aware
Fault with the electric assistance of the level of force in the steering wheel
motor. needed to turn the wheels. Consult an ap-
proved dealer
Fault in the assistance system.
The engine is overheating. The cool- Engine cooling fan not working. Stop the vehicle, switch off the engine and
ant temperature indicator is in the contact an approved dealer.
warning zone and warning light
® comes on.
Coolant boiling in the coolant reser- Mechanical fault: damaged cylinder Stop the engine.
voir. head gasket. Contact an approved dealer.
Radiator: If there is a significant lack of coolant, remember that it must never be topped up using cold coolant while
the engine is very warm. After any procedure on the vehicle which has involved even partial draining of the cooling
system, it must be refilled with a new mixture prepared in the correct proportions. Reminder: only products approved
by our Technical Department may be used for this purpose.
5.44
OPERATING FAULTS (5/6)
Electrical equipment POSSIBLE CAUSES WHAT TO DO
The wipers do not work. Wiper blades stuck. Free the blades before using the wipers.
The wiper does not stop. Faulty electrical controls. Consult an approved dealer.
Direction indicators flashing more Blown bulb. See information on “Headlights: changing
quickly. bulbs” or “Rear and side lights: changing
bulbs”.
The direction indicators do not work. Faulty electrical circuit or control. Consult an approved dealer.
The lights do not come on or go off. Faulty electrical circuit or control. Consult an approved dealer.
5.45
OPERATING FAULTS (6/6)
Electrical equipment POSSIBLE CAUSES WHAT TO DO
Traces of condensation in the lights Traces of condensation may be a nat-
and headlights. ural phenomenon caused by varia-
tions in temperature and humidity.
In this case, the traces will disappear
slowly once the lights are switched
on.
The front seat belt reminder light An object is stuck between the floor Remove all objects from underneath the
comes on when the seat belts are and the seat and is disrupting the op- front seats.
fastened. eration of the sensor.
5.46
Section 6: Technical specifications
A
1
2
3
4
5
A
10 6
9 7
8
6.2
ENGINE IDENTIFICATION PLATES
1 2
3 A
A
1 Engine type.
2 Engine suffix.
3 Engine number.
6.3
DIMENSIONS (in metres) (1/2)
Five-door version
1,448*
1,512
1,945
* unladen
6.4
DIMENSIONS (in metres) (2/2)
Estate version
1,445*
1,512
1,945
* unladen
6.5
ENGINE SPECIFICATIONS
Engine type
H4B Turbo D4F H5F Turbo K9K Turbo
(see engine plate)
Type of fuel It is essential that you use unleaded petrol of the octane rating stated on the Diesel: the label
Octane rating label inside the fuel filler flap. located in the fuel
filler flap indicates
authorised fuels.
Spark plugs Only use the spark plugs specified for your vehicle’s engine.
The type should be marked on a label affixed inside the engine compartment.
If it is not then contact an approved Dealer.
Fitting spark plugs other than those specified may damage the engine. –
6.6
WEIGHTS (in kg)
The weights indicated for a basic vehicle without options: they vary depending on the your vehicle’s equipment. Consult
your approved Dealer.
6.7
REPLACEMENT PARTS AND REPAIRS
Original parts are based on strict specifications and are subject to highly-specialised tests. Therefore, they are of at least the same
level of quality as the parts fitted originally.
If you always fit genuine replacement parts to your vehicle, you will ensure that it performs well. Furthermore, repairs carried out
within the manufacturer’s Network using original parts are guaranteed according to the conditions set out on the reverse of the
repair order.
6.8
SERVICE SHEETS (1/6)
VIN: ..................................................................................
6.9
SERVICE SHEETS (2/6)
VIN: ..................................................................................
6.10
SERVICE SHEETS (3/6)
VIN: ..................................................................................
6.11
SERVICE SHEETS (4/6)
VIN: ..................................................................................
6.12
SERVICE SHEETS (5/6)
VIN: ..................................................................................
6.13
SERVICE SHEETS (6/6)
VIN: ..................................................................................
6.14
ANTICORROSION CHECK (1/6)
If the continuation of the warranty is subject to repair, it is indicated below.
VIN: ..........................................................
Date of repair:
Date of repair:
Date of repair:
6.15
ANTICORROSION CHECK (2/6)
If the continuation of the warranty is subject to repair, it is indicated below.
VIN: ..........................................................
Date of repair:
Date of repair:
Date of repair:
6.16
ANTICORROSION CHECK (3/6)
If the continuation of the warranty is subject to repair, it is indicated below.
VIN: ..........................................................
Date of repair:
Date of repair:
Date of repair:
6.17
ANTICORROSION CHECK (4/6)
If the continuation of the warranty is subject to repair, it is indicated below.
VIN: ..........................................................
Date of repair:
Date of repair:
Date of repair:
6.18
ANTICORROSION CHECK (5/6)
If the continuation of the warranty is subject to repair, it is indicated below.
VIN: ..........................................................
Date of repair:
Date of repair:
Date of repair:
6.19
ANTICORROSION CHECK (6/6)
If the continuation of the warranty is subject to repair, it is indicated below.
VIN: ..........................................................
Date of repair:
Date of repair:
Date of repair:
6.20
ALPHABETICAL INDEX (1/5)
A C
ABS ..............................................................1.58, 2.23 → 2.26 catalytic converter................................................... 2.10 – 2.11
accessories........................................................................ 5.36 central door locking ........................... 1.5 → 1.10, 1.13 → 1.15
accessories socket ............................................................ 3.21 changing a bulb ............................................5.16 → 5.26, 5.26
additional methods of restraint .......................................... 1.30 changing a wheel.................................................... 5.11 – 5.12
side protection ............................................................. 1.29 changing gear ...............................................2.12, 2.44 → 2.46
to the front seat belts .......................................1.24 → 1.27 child restraint/seat ....................1.31 – 1.32, 1.34 → 1.42, 1.48
to the rear seat belts .................................................... 1.28 child safety......1.9, 1.12, 1.27, 1.31 – 1.32, 1.34 → 1.42, 1.48,
adjusting your driving position ......................1.16 → 1.23, 3.22 2.3, 3.13 – 3.14
advice on antipollution ....................................................... 2.18 child seats..........................................1.31 – 1.32, 1.34 → 1.42
air bag...........................................................1.24 → 1.30, 1.56 children ................................. 1.2, 1.9, 1.31 – 1.32, 3.13 – 3.14
activating the front passenger air bags ........................ 1.50 children (safety) .......................................................... 1.2, 1.12
deactivating the front passenger air bags .................... 1.48 cigar lighter ........................................................................ 3.21
air conditioning ........................................................3.4 → 3.12 cleaning:
air vents ...................................................................... 3.2 – 3.3 inside the vehicle .............................................. 4.16 – 4.17
anti-corrosion check ..............................................6.15 → 6.20 clock ....................................................................... 1.73 – 1.74
anti-corrosion protection .................................................... 4.13 closing the doors ...................................................1.11 → 1.15
anti-lock braking system: ABS ...............................2.23 → 2.26 control instruments ............................1.56 → 1.64, 1.73 – 1.74
antipollution controls ..................................................................1.52 → 1.55
advice .......................................................................... 2.18 courtesy light ............................................................ 3.16, 5.25
armrest: courtesy mirrors ........................................................ 3.15, 5.26
front .............................................................................. 3.18 cruise control ................................................1.59, 2.30 → 2.33
ashtray ............................................................................... 3.21 cruise control-speed limiter....................................2.27 → 2.33
assisted parking.....................................................2.40 → 2.43
audible and visual signals.................................................. 1.80 D
automatic gearbox (use) ........................................2.44 → 2.46 dashboard..............................................................1.52 → 1.55
automatic gearbox selector lever...........................2.44 → 2.46 deadlocking the doors ....................................................... 1.10
demisting
B rear screen ..................................................3.4, 3.7 → 3.10
battery............................................................ 4.12, 5.33 – 5.34 windscreen ..................................................3.5, 3.7 → 3.10
troubleshooting ................................................. 5.33 – 5.34 dimensions ................................................................. 6.4 – 6.5
bonnet......................................................................... 4.2 – 4.3 dipstick................................................................................. 4.4
brake fluid ............................................................................ 4.8 display ...................................................................1.56 → 1.62
bulbs doors/tailgate ...........................................................1.2 → 1.15
changing .................................................5.16 → 5.26, 5.26 driver assistance....................................................2.40 → 2.43
driver’s position .....................................................1.52 → 1.60
7.1
ALPHABETICAL INDEX (2/5)
driving ........2.2 → 2.5, 2.10 – 2.11, 2.13 → 2.17, 2.20 → 2.37, passenger compartment filter ........................................ 4.9
2.44 → 2.46 fitting a radio ...................................................................... 5.35
driving aids ............................................................2.40 → 2.43 fittings ....................................................................3.17 → 3.20
driving position front passenger air bag deactivation ................................. 1.48
settings ............................................................1.20 → 1.23 front seat adjustment .............................................1.17 → 1.19
driving recommendations ......................................2.13 → 2.17 front seats
adjustment .......................................................1.16 → 1.20
E fuel
ECO driving ...........................................................2.13 → 2.17 advice on fuel economy ...................................2.13 → 2.17
ECO mode .................................................................. 2.15, 3.9 consumption ...........................................2.13 → 2.15, 2.17
electric beam height adjustment ........................................ 1.81 filling ........................................................1.56, 1.85 → 1.87
electric windows ..................................................... 3.13 – 3.14 grade ................................................................1.85 → 1.87
electronic stability control: ESC .............................2.23 → 2.26 fuel consumption ..........................................2.13 → 2.15, 2.17
emergency brake assist.........................................2.23 → 2.26 fuel economy .........................................................2.13 → 2.17
emergency braking ................................................2.23 → 2.26 fuel filler cap ..........................................................1.85 → 1.87
emergency key ..........................................................1.2 → 1.4 fuel level ................................................................1.56 → 1.61
emergency spare wheel ............................................5.2 → 5.5 fuel tank
engine capacity ........................................................................ 1.85
technical specifications .................................................. 6.6 fuel tank capacity ...................................................1.85 → 1.87
engine coolant ..................................................................... 4.7 fuses ......................................................................5.27 → 5.31
engine oil ...................................................................4.4 → 4.6
engine oil capacity ...................................................... 4.5 – 4.6 G
engine oil level ...........................................................4.4 → 4.6 gear lever........................................................................... 2.12
engine specifications .................................................... 6.3, 6.6
engine standby ..........................................................2.6 → 2.9 H
engine start/stop button .............................................2.3 → 2.5 handbrake.......................................................................... 2.12
environment ....................................................................... 2.19 hands-free telephone integrated control ............................ 3.33
ESC: electronic stability control ....................1.58, 2.23 → 2.26 hazard warning lights signal .............................................. 1.80
external temperature ......................................................... 1.74 headlight beam adjustment ............................................... 1.81
headrest.................................................................... 1.16, 3.22
F heated seats ...................................................................... 1.17
faults heated windscreen ..................................................3.7 → 3.10
operating faults ................................................5.41 → 5.46 heating and air conditioning system ........................3.4 → 3.11
filter heating system ........................................................3.4 → 3.10
air filter ........................................................................... 4.9 Hill Start Assist.......................................................2.23 → 2.26
oil filter .................................................................. 4.5 – 4.6 horn ................................................................................... 1.80
7.2
ALPHABETICAL INDEX (3/5)
horn: lights:
flash ............................................................................. 1.80 adjusting ...................................................................... 1.81
hubcap tool ............................................................... 5.9 – 5.10 brake lights ......................................................5.19 → 5.24
dipped beam headlights .................1.56, 1.76, 5.16 → 5.18
I direction indicators .........................1.56, 1.80, 5.16 → 5.19
indicator lights.................................................................... 5.24 fog lights .................................................... 1.56, 1.78, 5.19
indicators ......................................................1.80, 5.16 → 5.24 hazard warning ............................................................ 1.80
indicators: main beam headlights ................................ 1.56, 1.76, 5.16
direction indicators ....................................................... 1.80 number plate lights ...................................................... 5.24
instrument panel ..............................................1.56 → 1.64 reversing lights ............................................................. 5.19
instrument panel ....................................................1.56 → 1.72 side lights ................................................1.76, 5.16 → 5.19
instrument panel messages...................................1.63 → 1.72 load permitted on the roof.................................................... 6.7
interior trim locking the doors .....................................................1.2 → 1.15
maintenance ..................................................... 4.16 – 4.17 luggage compartment cover .............................................. 3.26
Isofix ....................................................................... 1.34 – 1.35 luggage retaining net .............................................. 3.30 – 3.31
J M
jack ...................................................................................... 5.9 maintenance ...................................................................... 2.18
maintenance:
L bodywork .........................................................4.13 → 4.15
levels .........................................................................4.7 → 4.9 interior trim ........................................................ 4.16 – 4.17
levels: mechanical .........................................4.4, 4.12, 6.9 → 6.14
brake fluid ...................................................................... 4.8 map reading lights ............................................................. 3.16
coolant ........................................................................... 4.7 methods of restraint in addition to the seat belts ...1.24 → 1.30
windscreen washer reservoir ......................................... 4.9 multimedia equipment .............................................. 3.33, 5.35
lifting the vehicle
changing a wheel .............................................. 5.11 – 5.12 N
lighting: navigation system .............................................................. 3.33
exterior .............................................................1.76 → 1.81
instrument panel .......................................................... 1.76 O
interior ............................................. 3.16, 5.25 – 5.26, 5.26 oil change ................................................................... 4.5 – 4.6
lights opening the doors ..................................................1.11 → 1.14
adjustment ................................................................... 1.81 operating faults ................................ 1.56 → 1.60, 5.41 → 5.46
changing bulbs .................................................5.16 → 5.18
front ..................................................................5.16 → 5.18
7.3
ALPHABETICAL INDEX (4/5)
P signals and lights ...................................................1.76 → 1.81
paintwork speakers
maintenance ....................................................4.13 → 4.15 location ........................................................................ 5.35
parking assistance: assisted parking .....................2.40 → 2.43 special features of diesel versions..................................... 2.11
parking distance control.........................................2.34 → 2.37 special features of petrol vehicles ..................................... 2.10
power-assisted steering..................................................... 1.51 speed limiter .................................................1.59, 2.27 → 2.29
pretensioners .........................................................1.24 → 1.27 starting the engine .....................................................2.3 → 2.9
puncture.................................................5.2 → 5.9, 5.11 – 5.12 steering wheel
adjustment ................................................................... 1.51
R Stop & Start ......................................................1.59, 2.6 → 2.9
radio................................................................................... 3.33 Stop & Start function..................................................2.6 → 2.9
rear bench seat.................................................................. 3.23 stopping the engine ...................................................2.3 → 2.5
rear parcel shelf ................................................................. 3.25 storage compartment.............................................3.17 → 3.20
rear seats........................................................................... 1.22 storage compartments ...........................................3.17 → 3.20
functions ...................................................................... 3.23 sun visor ............................................................................ 3.15
rear view mirrors ................................................................ 1.75 switching on the vehicle ignition ................................2.3 → 2.5
RENAULT ANTI-INTRUDER DEVICE (RAID) ................... 1.15
RENAULT card T
battery .......................................................................... 5.32 tailgate ........................................................... 3.24, 3.27 – 3.28
use ................................................... 1.2 → 1.10, 2.3 → 2.5 tanks and reservoirs
RENAULT card battery ...................................................... 5.32 brake fluid ...................................................................... 4.8
replacement parts ................................................................ 6.8 coolant ........................................................................... 4.7
reverse gear tanks and reservoirs:
selecting ....................................................................... 2.12 windscreen washer ........................................................ 4.9
reversing sensor ....................................................2.34 → 2.37 technical specifications ..............................................6.4 → 6.8
roof bars ............................................................................ 3.32 telephone ........................................................................... 3.33
roof rack temperature regulation ............................................3.7 → 3.10
roof bars ....................................................................... 3.32 tool kit .................................................................................. 5.9
running in ............................................................................. 2.2 towing
breakdown ........................................................ 5.39 – 5.40
S towing equipment ......................................................... 3.29
seat belt pretensioners towing a caravan ........................................................ 3.29, 6.7
front seat belt ...................................................1.24 → 1.27 towing equipment
seat belts ......................................................1.20 → 1.27, 1.30 fitting ............................................................................ 3.29
service sheets..........................................................6.9 → 6.14 towing hitch...................................................... 5.9, 5.39 – 5.40
side protection devices ...................................................... 1.29 towing rings ............................................................ 3.27 – 3.28
7.4
ALPHABETICAL INDEX (5/5)
towing weights ..................................................................... 6.7
traction control ..............................................1.58, 2.23 → 2.26
transporting children .................1.31 – 1.32, 1.34 → 1.42, 1.48
transporting objects
in the luggage compartment ........................................ 3.28
luggage net ....................................................... 3.30 – 3.31
on the roof ...................................................................... 6.7
trims ................................................................................... 5.10
trip computer and warning system... 1.56 → 1.60, 1.63 → 1.72
tyre inflation kit...........................................................5.6 → 5.8
tyre pressure.............................2.20 → 2.22, 4.10 – 4.11, 5.14
tyre pressure loss warning.....................................2.20 → 2.22
tyre pressures ......................................................... 4.10 – 4.11
tyres .................... 2.17, 2.20 → 2.22, 4.10 – 4.11, 5.13 → 5.15
U
unlocking the doors ................................................ 1.13 – 1.14
V
variable power-assisted steering ....................................... 1.51
vehicle identification plates .................................................. 6.3
ventilation ................................................................3.2 → 3.10
W
warning lights.........................................................1.56 → 1.72
washing .................................................................4.13 → 4.15
weights ................................................................................ 6.7
wheelbrace .......................................................................... 5.9
wheels (safety) ......................................................5.13 → 5.15
windscreen de-icing/demisting ................................3.7 → 3.10
windscreen washer ................................................1.82 → 1.84
wiper blades ........................................................... 5.37 – 5.38
wipers ....................................................................1.82 → 1.84
blades ............................................................... 5.37 – 5.38
7.5
7.6
Renault s.a.s. Société par Actions Simplifiée au capital de 533 941 113 € /13-15, quai Le Gallo
92100 Boulogne-Billancourt R.C.S. Nanterre 780 129 987 — SIRET 780 129 987 03591 / Tél. : 0810 40 50 60
NU 1189-4 – 99 91 051 91R – 06/2017 – Edition anglaise
à999105191Ròñêä E6