Documente Academic
Documente Profesional
Documente Cultură
ing on
For work
sitive
static sen
electronic
nts!
compone
Static Dissipative
Wiha
Germany
Quality Tools
2 Toll Free: (800) 494-6104
What is ESD? Types of ESD Damage
Static damage to components can take the form of upset failures or catastrophic
Basic Concepts in Electrostatic Discharge (ESD) failures.
We have all seen static electricity in the form of lightning or perhaps felt the
zap when reaching for a door knob. Similar types of electrical charges can have · Upset failures - result in gate leakage
an effect on the electronic components you handle every day in your work. · Catastrophic failures - occur in two forms, Direct and Latent
Unfortunately, their effect is much more hazardous and not as readily apparent.
Direct catastrophic failures occur when a component is damaged to the point
Definition where it is DEAD NOW and it will never again function. This is the easiest type of
Static electricity is an electrical charge at rest. Static electricity is most commonly ESD damage to find since it usually can be detected during testing.
created by friction and separation. Friction causes heat which excites the molecular
particles of the material. When two materials are then separated, a transfer of Latent failures occur when ESD weakens or wounds the component to the point
electrons from one material to the other may take place. where it will still function properly during testing, but over time the wounded
component will cause poor system performance and eventually complete system
As electrons transfer, the absence or surplus of electrons creates an electrical field failure. Because latent failures occur after final inspection or in the hands of your
known as static electricity. The simple separation of two materials, as when tape is customer, the cost for repair is very high. Not only is this type of damage hard to
pulled off a roll, can also create this same transfer of electrons between materials, find, but it severely affects the reputation of your company’s product.
generating static electrical fields.
An upset failure occurs when an electrostatic discharge has caused a current flow
The amount of static electricity generated depends upon the materials subjected that is not significant enough to cause total failure, but in use may intermittently
to friction or separation, the amount of friction or separation and the relative result in gate leakage causing loss of software or incorrect storage of information.
humidity of the environment. Common plastic generally will create the greatest
static charge. Low humidity conditions such as those created when air is heated Upset or latent failures may pass your company’s quality control testing program.
during the winter will also promote the generation of significant static electrical In other words, static damage may occur that cannot be felt, seen, or detected
charges. through normal testing procedures.
Materials that easily transfer electrons (or charge) between atoms are called Think of Static As Contamination!
conductors and are said to have “free” electrons. Some examples of conductors Damage caused by invisible and undetectable events can be understood by
are metals, carbon and the human body’s sweat layer. Materials that do not easily comparing ESD damage to medical contamination of the human body by viruses
transfer electrons are called insulators. Some well known insulators are common or bacteria. Although viruses and bacteria are invisible, they can cause severe
plastics, glass and air. Both conductors and insulators may become “charged” with damage even before you can detect their presence. A defense against this invisible
static electricity. When a conductor is charged, the free electrons give it the ability threat is sterilization.
to discharge rapidly when it comes close to another conductor with a different
potential. As an employee, the hidden threat of electrostatic discharge or ESD should be
of great concern to you. ESD damage can significantly reduce your company’s
Typical Electrostatic Voltages profitability. This may affect your profit sharing, your company’s ability to
Many of the common activities you perform daily may generate charges on your compete in the market place and even your employment. Everyone likes to take
body that are potentially harmful to components. pride in their work, but without proper ESD controls, your best efforts may be
destroyed by static electricity that you can neither feel nor see.
Some of these activities include:
· Walking across a carpet, 1,500 to 35,000 volts
· Walking over untreated vinyl floor, 250 to 12,000 volts ESD Safe Precision Screwdrivers
· Worker at a bench, 700 to 6,000 volts
· Vinyl envelope used for work instructions, 600 to 7,000 volts Description Page
· Picking up a common plastic bag from a bench, 1,200 to 20,000 volts
SYSTEM 4 10-13
This Article courtesy of Desco Industries, Inc
Wiha Quality Tools
Germany
ESD Safe Micro Bit Handles/Bits & Sets ESD Safe Drive-Loc VI Handle
Description Page Description Page
ESD Safe SYS 4 ESD Safe Micro Bit Sets ESD Safe TorqueControl Tools
TorqueControl Blades 22
ESD Safe Cushion Grip Bit Holders
ESD Safe Pliers & Cutters Index
Description Page
Description Page
SoftFinish® Bit Holders 17 Diagonal Cutters 23
Tapered Head
Quick Release Bit Holder 17
Diagonal Cutters 24-25
Wide Tapered & Oval Head
Diagonal Cutters 25
ESD Safe Cushion Grip Screwdrivers Wide Oval & Wide Form
Tapered handle
allows rapid rotation
Blade, CVM steel, hardened,
hard chrome finish
D
273 Phillips Screwdriver, With Precision ESD Safe Dissipative 273 99
Set 8 Pcs. Slotted & Phillips Precision ESD Safe
Handle Blade high alloy chrome-vanadium-molybdenum steel. Dissipative Handle Blade high alloy CVM steel, hardened,
Hard chrome finished. Handle manufactured from impact resistant, hard chromed. Handle manufactured from impact resistant,
dissipative material. ESD standard IEC 61340-5-1 dissipative material. In storage pouch. ESD standard IEC 61340-5-1
Item Item
No. Size mm Inch mm Inch mm Inch lbs. pkg. No. mm mm Size mm lbs.
273 02 000 40 1.6 2.0 .08 120 4.7 .02 10 273 99 272 15 1.5 40 273 02 000 40 .50
273 05 00 40 1.6 2.0 .08 120 4.7 .02 10 272 20 2.0 40 273 05 00 40
273 07 00 75 3.0 2.0 .08 155 6.1 .02 10 272 25 2.5 50 273 10 0 50
273 10 0 50 2.0 3.0 .12 145 5.7 .04 10 272 30 3.0 50 273 20 1 60
273 12 0 75 3.0 3.0 .12 170 6.7 .03 10
273 14 0 100 3.9 3.0 .12 195 7.6 .05 10
273 16 0 150 5.9 3.0 .12 245 9.6 .06 10
273 20 1 60 2.3 4.0 .16 170 6.7 .06 10
273 22 1 75 3.0 4.0 .16 155 6.1 .06 10
273 24 1 100 3.9 4.0 .16 210 8.2 .06 10
273 26 1 150 5.9 4.0 .16 260 10.2 .07 10
*Metric dimensions actual - Inch dimensions approximate
D
Set
273 93 7 Pcs. Extra Long Slotted/Phillips Precision ESD Safe
Dissipative Handle Blade CVM steel, hardened, hard chromed. Handle
impact resistant, dissipative material. ESD standard IEC 61340-5-1
Item
No. mm mm Size mm lbs.
273 93 272 24 2.0 150 273 16 0 150 .50
272 28 2.5 150 273 26 1 150
272 34 3.0 150
272 38 3.5 150
272 43 4.0 150 911 18 Rugged Polyester Canvas Storage Pouch
Holds 8 Precision Tools up to 170mm in length. Folding pouch.
Has security flaps and velcro closer.
Item
No. Size lbs. pkg.
911 18 14 1/2” W x 7 3/4” L .13 1
Wiha
Germany
Quality Tools
6 Toll Free: (800) 494-6104
ESD standard
D IEC 61340-5-1
Set
278 99 8 Pcs. Precision ESD Safe Dissipative Handle
Set In Pouch Blade high alloy CVM steel, hardened, hard chromed.
Handle impact resistant, dissipative material.
Item
No. Size mm Size mm lbs.
278 99 278 01 T1 40 278 05 T5 40 .47
278 02 T2 40 278 06 T6 40
278 03 T3 40 278 07 T7 40
278 04 T4 40 279 20 Chip Lifter
Wiha Quality Tools
Germany
920 92 Master Technicians Bench Top Set 271 Ceramic Phillips Screwdriver, With Wiha-Precision Handle,
Plexiglass frame. Equipped with 50 precision ESD Safe screwdrivers. Out of Anti-static Plastic Blade special ceramic,
Item No. antimagnetic, for correct adjusting in high frequency areas.
920 92 Slotted: .8, 1.0, 1.2, 1.5, 2.0, 2.5, 3.0, 3.5, 4.0mm Item
Phillips: #000, #00, #0, #1 No. Size mm Inch mm Inch lbs. pkg.
Torx: T1, T2, T3, T4, T5, T6, T7, T8, T9, T10, T15, T20 271 00 0 15.0 .59 94.5 3.7 .14 1
lbs. 2.25 Metric Hex: .7, .9, 1.3, 1.5, 2.0, 2.5, 3.0, 4.0mm *Metric dimensions actual - Inch dimensions approximate
Inch Hex: 1/16, 5/64, 3/32, 7/64, 1/8, 9/64, 5/32”
Metric Nut Drivers: 1.5, 2.0, 2.5, 3.0, 3.5, 4.0, 4.5, 5.0, 5.5mm
279 20 Chip Lifter
Rotating Cap
Precision Handle for precise
high quality turning and control
plastic, cadmium
free. ESD Safe
or Standard styles
Collet Lock Handle
adjustable blade length from
15 to 95mm/.6” to 3.75”
95mm 15mm
Tips
Blades
Exact fit,
chrome-vanadium-
precision machined Tapered Handle
molybdenum steel,
allows rapid rotation,
hardened, hard chromed
requires less clearance
280 00 ESD Safe Dissipative Precision 269 SYSTEM 4 Slotted Reversible Blade 269 SYSTEM 4 Phillips Reversible Blade
Handle with rotating control cap. Surface High alloy chrome-vanadium-molybdenum High alloy CVM steel, hardened, hard chromed.
resistant 106-109 Ohms. 4 mm hex retainer steel, hardened, hard chromed. Wiha vapor Wiha vapor Chrome-Top finish on tips.
for all SYSTEM 4 interchangeable blades. Chrome-Top finish on tips. Item
Tapered handle, high quality plastic, impact Item No. Size Size mm Inch lbs.
resistant. Ball retainer hold. 110mm/4.3” OAL No. mm mm mm Inch lbs. 269 11 000 + 00 120 4.7 .03
Item 269 03 1.5 + 3.0 120 4.7 .05 269 12 0 + 1 120 4.7 .03
No. mm Inch mm Inch lbs. 269 04 2.0 + 3.5 120 4.7 .05
280 00 4.0 .1574 14.0 .55 .04 269 05 2.5 + 4.0 120 4.7 .06
269 SYSTEM 4 Metric Ball End & 269 SYSTEM 4 Metric Hex Sizes, 269 SYSTEM 4 Nut Driver Inch,
Standard Hex, Reversible Blade Interchangeable Blade High alloy CVM steel, Interchangeable Blade High alloy chrome-
CVM steel, hardened, hard chromed. Wiha hardened, corrosion protected. vanadium-molybdenum steel, hardened,
vapor Chrome-Top finish on tips. One side Item corrosion protected. 120mm/4.7” OAL
hex, other side ballpoint hex. No. mm mm Inch lbs. Item
Item 269 13 0.7 120 4.7 .06 No. Inch Inch Inch lbs.
No. mm mm mm Inch lbs. 269 14 0.9 120 4.7 .06 269 62 3/32 .16 .16 .04
269 32 1.3 + 1.3 120 4.7 .05 269 15 1.3 120 4.7 .06 269 63 7/64 .20 .20 .04
269 33 1.5 + 1.5 120 4.7 .05 269 16 1.5 120 4.7 .06 269 64 1/8 .20 .20 .04
269 34 2.0 + 2.0 120 4.7 .06 269 17 2.0 120 4.7 .06 269 65 9/64 .21 .24 .04
269 35 2.5 + 2.5 120 4.7 .06 269 18 2.5 120 4.7 .06 269 66 5/32 .22 .24 .04
269 36 3.0 + 3.0 120 4.7 .06 269 19 3.0 120 4.7 .06 269 67 3/16 .26 .28 .04
269 37 4.0 + 4.0 120 4.7 .06 269 20 4.0 120 4.7 .06 269 68 7/32 .30 .32 .04
269 69 1/4 1.34 .36 .04
For angle
entry
280 SYSTEM 4 Metric Ball End Hex 269 SYSTEM 4 Inch Hex Sizes, 269 SYSTEM 4 Reversible Blade
Interchangeable Blade High alloy tool steel, Interchangeable Blade High alloy chrome-vanadium-molybdenum
hardened, corrosion protected. Ball end works High alloy chrome-vanadium-molybdenum steel, hardened, vapor chrome protected,
at 30° angle entry for easy access to fasteners. steel, hardened, corrosion protected. Wiha vapor Chrome-Top finish on tips.
Item Item 120mm/4.7” OAL.
No. mm mm Inch lbs. pkg. No. Inch mm Inch lbs. Item
280 33 1.5 120 4.7 .06 1 269 21 .050 120 4.7 .06 No. Size Size lbs.
280 34 2.0 120 4.7 .06 1 269 23 1/16 120 4.7 .06 269 51 T6 + T8 .03
280 35 2.5 120 4.7 .06 1 269 24 5/64 120 4.7 .06 269 52 T7 + T9 .03
280 36 3.0 120 4.7 .06 1 269 25 3/32 120 4.7 .06 269 53 T10 + T15 .03
280 37 4.0 120 4.7 .06 1 269 26 7/64 120 4.7 .06 269 54 T15 + T20 .03
269 27 1/8 120 4.7 .06
269 28 9/64 120 4.7 .06
269 29 5/32 120 4.7 .06
For angle
entry
280 SYSTEM 4 Inch Ball End Hex 269 SYSTEM 4 Nut Driver Metric, 269 SYSTEM 4 Interchangeable
Interchangeable Blade High alloy tool steel, Interchangeable Blade High alloy chrome- Blade High alloy CVM steel, hardened,
hardened, corrosion protected. Ball end works vanadium-molybdenum steel, hardened, Wiha vapor Chrome-Top finish on tips.
at 30° angle entry for easy access to fasteners. corrosion protected. 120mm/4.7” OAL 120mm/4.7” OAL
Item Item Item
No. Inch mm Inch lbs. No. mm mm Inch Inch lbs. No. Size lbs.
280 21 .050 120 4.7 .06 269 40 1.5 + 1.8 .12 .12 .03 269 55 T3 .03
280 23 1/16 120 4.7 .06 269 41 2.0 + 2.5 .16 .16 .03 269 56 T4 .03
280 24 5/64 120 4.7 .06 269 38 1.5 - .11 .11 .04 269 57 T5 .03
280 25 3/32 120 4.7 .06 269 39 1.8 - .12 .12 .04
280 26 7/64 120 4.7 .06 269 49 2.0 - .13 .13 .06
280 27 1/8 120 4.7 .06 269 50 2.5 - .16 .16 .06
280 28 9/64 120 4.7 .06 269 42 3.0 - .20 .20 .06
280 29 5/32 120 4.7 .06 269 43 3.2 - .20 .20 .06
269 44 3.5 - .22 .24 .06
269 45 4.0 - .22 .24 .06
269 46 4.5 - .25 .28 .06
269 47 5.0 - .27 .28 .06
269 48 5.5 - .30 .32 .06
Wiha
Germany
Quality Tools
12 Toll Free: (800) 494-6104
Wiha Canvas Pouch Sets Surface resistance of handles is 106 - 109 Ohms
Canva
s Pouc
h
D D
Canva
269 90 Slotted & Phillips Precision 280 80 Slotted, Phillips & Hex s Pouc
h
Interchangeable Blade Set, 4 Pcs. Wiha ESD Precision Interchangeable Blade Set, 22 Pcs.
Safe precision collet lock handle and Wiha ESD Safe precision collet lock handle
3 Wiha interchangeable blades. and 20 Wiha interchangeable blades.
269 90 Set includes the following blades: 280 80 Set includes the following blades:
Slotted Sizes: 2.0, 3.0, 4.0mm Slotted Sizes: 1.5, 2.0, 3.0, 4.0mm
Phillips Sizes: 00, 0, 1 Phillips Sizes: 000, 00, 0, 1
lbs. .17 Torx Sizes: T3, T4, T5, T6, T7, T8,
T9, T10, T15
Canva Hex Sizes: .028, .035
s Pouc
h Ball Hex Sizes: .050, 1/16, 5/64, 3/32,
7/64, 1/8, 9/64, 5/32”
D ESD Safe Chip Lifter
lbs. .33
269 91 Slotted & Phillips Precision
Interchangeable Blade Set, 6 Pcs. Wiha ESD
Safe precision collet lock handle and 5 Wiha
interchangeable blades. In canvas pouch.
269 91 Set includes the following blades:
Slotted Sizes: 1.5, 2.0, 2.5, 3.0, 3.5, 4.0mm
ESD Technicians Kit
Phillips Sizes: 000, 00, 0, 1
Precision Screwdrivers & Tweezers
lbs. .29
Slotted,
D
Phillips, Hex
D Canva
445 90 Slotted, Phillips and Precision s Pouc
Canva h
s Pouc
269 92 Slotted, Phillips and Ball End Hex h Interchangeable Blade Set, 12 Pcs. Wiha ESD
Metric/Inch Precision Interchangeable Blade Safe precision collet lock handle, 7 Wiha
Set, 17 Pcs. Wiha ESD Safe precision collet interchangeable blades & 4 ESD Safe Tweezers.
lock handle and 15 Wiha interchangeable blades. 445 90 Set includes the following blades:
269 92 Set include the following blades: Slotted Sizes: 2.0, 3.0, 4.0mm
Slotted Sizes: 1.5, 2.0, 3.0, 4.0mm Phillips Sizes: 00, 0, 1
Phillips Sizes: 000, 00, 0, 1 Torx Sizes: T6, T7, T8, T9, T10, T15
Ball End Hex Inch: .050,1/16, 5/64, ESD Safe Precision Tweezers:
7/64, 3/32,1/8” 44501 Fine Point - AA SA
Ball End Hex Metric: 1.5, 2.0, 2.5, 44509 Extra Fine Point - 5 SA
3.0, 4.0mm 44505 Flat and Blunt - 2a SA
ESD Safe Chip Lifter 44510 Curved Fine Point - 7a SA
lbs. .63 lbs. .60
Slotted, Phillips, Torx® Set In Steel Box Slotted & Phillips Set In Steel Box
Surface resistance Surface resistance
of handles is of handles is
D 106 - 109 Ohms 106 - 109 Ohms
D
280 94 Slotted, Phillips & Torx Precision
®
269 93 Slotted & Phillips Precision
Interchangeable Blade Set, 11 Pcs. Wiha Interchangeable Blade Set, 6 Pcs. Wiha ESD
ESD Safe precision collet lock handle and Safe precision collet lock handle and 5 Wiha
10 Wiha interchangeable blades. interchangeable blades.
280 94 Set includes the following blades: 269 93 Set includes the following blades:
Slotted Sizes: 1.5, 2.0, 3.0, 4.0mm Slotted Sizes: 1.5, 2.0, 2.5, 3.0, 3.5, 4.0mm
Phillips Sizes: 000, 00, 0, 1 Phillips Sizes: 000, 00, 0, 1
: T3, T4, T5, T6, T7, T8, T9, T10, T15 lbs. .87
lbs. 1.51
Wiha Quality Tools
Germany
D
269 87 Precision Interchangeable
D
Blade Set, 8 Pcs. Wiha ESD Safe precision
269 89 Hex Inch Precision Blade Set, collet lock handle and 7 interchangeable blades.
9 Pcs. Wiha ESD Safe Precision Collet Lock 269 87 Set includes the following blades:
handle and 8 Wiha interchangeable blades. Sizes on standard blades:
269 89 Set includes the following blades: T3, T4, T5
Hex Inch Sizes: .050, 1/16, 5/64, 3/32, Sizes on reversible blades:
7/64, 1/8, 9/64, 5/32” T6, T7, T8, T9, T10, T15, T20
lbs. .35 lbs. .33
Wiha
Germany
Quality Tools
14 Toll Free: (800) 494-6104
Wiha SYSTEM 4 Micro Bits
SYSTEM 4
Handles & 750 SYSTEM 4 Slotted Bits High alloy 757 SYSTEM 4 Bits
CVM steel, hardened, on 4 mm hex stock. High alloy chrome-vanadium-molybdenum
Micro Bits Item steel, hardened, on 4 mm stock.
No. mm mm Inch lbs. Item
Tips
Exact fit, Rotating Cap 750 08 0.8 28 1.1 .01 No. Size mm Inch lbs.
precision for precise 750 12 1.2 28 1.1 .01 757 03 T3 28 1.1 .01
machined turning & control 750 15 1.5 28 1.1 .01 757 04 T4 28 1.1 .01
750 18 1.8 28 1.1 .01 757 05 T5 28 1.1 .01
Tapered Handle
allows rapid rotation, 750 20 2.0 28 1.1 .01 757 06 T6 28 1.1 .01
requires less clearance. 750 25 2.5 28 1.1 .01 757 07 T7 28 1.1 .01
Static Dissipative 750 30 3.0 28 1.1 .01 757 08 T8 28 1.1 .01
106 - 109 ohms 750 35 3.5 28 1.1 .01 757 09 T9 28 1.1 .01
Bits CVM steel, 750 40 4.0 28 1.1 .01 757 10 T10 28 1.1 .01
hardened 757 15 T15 28 1.1 .01
Use bits directly in handle or with 4” bit extension 757 20 T20 28 1.1 .01
NEWFrom
Wiha Bits hardened for
extreme durability
Surface resistance
of handles is
106 - 109 Ohms
750 93 SYSTEM 4 Slotted, Phillips, 750 95 SYSTEM 4 Slotted, Phillips, Hex Metric
Compact ESD Precision Interchangeable Bit Compact ESD Precision Interchangeable Bit
Set, 16 Pcs. Wiha precision handle, bit extension Set, 16 Pcs. Wiha precision handle, bit extension
& 14 interchangeable bits. & 14 interchangeable bits.
Item No. Combination Bit Set
750 93 Set with Standard Precision Handle NEW
From
Item No. Combination Bit Set
750 95 Set with Standard Precision Handle NEW
From
Wiha
Set includes the following bits: Wiha Set includes the following bits:
Slotted: 1.5, 2.0, 2.5, 3.0mm Slotted: 1.5, 2.0, 2.5, 3.0mm
Phillips: 00, 0, 1 Phillips: 00, 0, 1
: T6, T7, T8, T9, T10, T15, T20 Hex Metric: .9, 1.3, 1.5, 2.0,
105mm Bit Extension 2.5, 3.0, 4.0mm
lbs. .17 105mm Bit Extension
lbs. .17
NEW
Set includes the following bits:
Slotted: 1.5, 2.0, 2.5, 3.0mm
Phillips: 00, 0, 1 From
Wiha
Hex Inch: .035, .050, 1/16, 5/64,
3/32, 7/64, 1/8”
105mm Bit Extension 759 02
SYSTEM 4 Micro Bit 1/4” Drive Power Tool Adapter
lbs. .17 Shaft CVM steel, hardened, corrosion protected. 1/4” Hex drive
holds 4 mm bits. Without magnet
Item
No. Size mm mm lbs.
759 02 1/4” 60 4.0 .05
Wiha Quality Tools
Germany
Dissipative
NEW
Bit holders without material offers
protection against
Wiha
magnetics
From electrostatic
discharge
Surface resistance
of handles is
106 - 109 Ohms
NEW
From
Wiha
NEW
From
D Wiha
D
ESD
387 01 Safe Quick Release 1/4” Bit Holder, With Wiha- 281 80
ESD Safe Stubby 1/4” Bit Holder With Ring Retainer,
SoftFinish® Cushion Grip Handle, IEC 61340-5-1, DIN 3126, ISO 1173 Cushion Grip Wiha-SoftFinish® Handle, IEC 61340-5-1, DIN 3126,
Stainless steel with retaining ring bit holder. Dissipative SoftFinish® ISO 1173 Dissipative SoftFinish® cushion grip handle, multi-
cushion grip handle, multi-component, ESD Safe surface resistance component, ESD Safe surface resistance 106 - 109 Ohm.
106 - 109 Ohm. Item
Item No. Inch mm Inch lbs. pkg.
No. Inch mm Inch mm Inch lbs. pkg. 281 80 1/4” 57 2.2 .11 1
387 01 1/4” 148 5.8 38 1.5 .18 1
In Durable Pouch
NEW
From
Wiha
Surface
resistance
of handle is
106 - 109
Ohms
387 90 ESD Safe 1/4” Quick Release Bit Holder Set With
Interchangeable 70mm Power Bits & Quick Release Bit Holder
20 Pc. set includes ESD Safe Quick Release Bit Holder, cushion grip
handle, stainless steel with retaining ring bit holder. 70mm Power Bits,
CVM tool steel, hardened. Quick Release Bit Holder for power bits.
Item
No. 387 90
Slotted: 2.5, 3.0, 3.5, 4.0, 5.5, 6.5mm Phillips: 0, 1, 2
TORX®: T6, T7, T8, T9, T10, T15 Pozidriv®: 0, 1, 2
Available after January 1st, 2010
Wiha Quality Tools
Germany
Dissipative material
offers protection against
electrostatic discharge
D
302 92 Set 6 Pcs. ESD Safe Slotted & Phillips
DIN EN 61340-5-1/61340-5-2 Round blade, high alloy CVM steel,
D
hardened, hard chromed. Dissipative SoftFinish® cushion grip handle,
SoftFinish cushion multi-component, ESD Safe (106-109 Ohm).
grip handle Item
No. mm Inch mm Size mm lbs.
CVM steel hardened, 302 92 302 42* 3.0 .118 100 311 50 0 60 .96
hard chrome Finish 302 44* 4.0 .157 100 311 51 1 80
302 46* 5.5 .216 125 311 52 2 100
DIN EN 61340-5-1/ 61340-5-2 *Cabinet Tips
311
ESD Safe Phillips Screwdriver, With Wiha-SoftFinish® Handle
DIN EN 61340-5-1/61340-5-2 Round blade, high alloy CVM steel,
hardened, hard chromed. Offers protection against electrostatic
D
discharge. Dissipative SoftFinish® cushion grip handle, 362 89 Set 6 Pcs. ESD Safe Screwdrivers
multi-component, ESD Safe (106-109 Ohm). Round blade high alloy chrome-vanadium-molybdenum steel,
Item hardened, Hard chrome finish with Wiha-Chromtop satin grip tips.
No. Size mm Inch mm Inch mm Inch lbs. pkg. Molded on SoftFinish® cushion grip handle, multi-component.
311 50 0 60 2.4 3.0 1/8 164 6.5 .06 10 Item
311 51 1 80 3.1 4.5 3/16 191 7.5 .11 10 No. Size mm Size mm lbs.
311 52 2 100 3.9 6.0 1/4 218 8.6 .20 10 362 89 362 06 T6 60 362 18 T10 80 .81
362 08 T8 60 362 19 T15 80
362 09 T9 60 362 24 T20 100
Wiha Quality Tools
Toll Free: (800) 494-6104 19
Surface
resistance
of handle is
106 - 109 Ohms
281
Drive-Loc VI Interchangeable Blade
High alloy CVM steel, through hardened, hard chrome finish.
Over all blade length 150mm/5.9”. Blades fit all Drive-Loc VI handles.
Surface Item
resistance
No. Size + Size lbs. pkg.
of handle is
106 - 109 Ohms 281 26 T6 T8 .10 1
281 27 T7 T9 .10 1
ESD
284 86 Safe Drive-Loc VI Cushion Grip Handle 281 28 T10 T15 .10 1
Wiha-SoftFinish® impact resistant, with roll off protection. 281 29 T20 T25 .10 1
Advantages: 281 30 T30 T40 .10 1
Ergonomic cushion grip, Drive-Loc mechanism guarantees a secure
hold and rapid blade exchange. Static Dissipative.
Item
No. mm mm Inch mm Inch lbs.
284 86 6.0 115 4.5 36.0 1.41 .21 281
Tamper Resistant Drive-Loc VI Interchangeable Blade,
high alloy CVM steel, through hardened, hard chrome finish.
Wiha Drive-Loc VI Blades Over all blade length 150mm/5.9”. Blades fit all Drive-Loc VI handles.
Item
No. Size + Size lbs. pkg.
281 32 T6s T8s .10 1
281
Slotted Drive-Loc VI Interchangeable Blade High alloy CVM 281 33 T7s T9s .10 1
steel, through hardened, hard chrome finish. Over all blade length 281 34 T10s T15s .10 1
150mm/5.9”. Blades fit all Drive-Loc VI handles. 281 35 T20s T25s .10 1
Item 281 36 T30s T40s .10 1
No. mm + mm lbs. pkg.
281 06 3.5 4.5 .10 1
281 08 5.5 6.5 .10 1
281
Ball End Hex & Hex Metric Drive-Loc VI Interchangeable
Blade High alloy CVM steel, through hardened, hard chrome finish. 281 Drive-Loc VI Inch Nut Driver Blades
Ball end enables the user to work at angles up to 25O. Over all blade High alloy CVM steel, through hardened, hard chrome finish.
length 150mm/5.9”. Blades fit all Drive-Loc VI handles. OAL blade length 150mm/5.9”. Blades fit all Drive-Loc VI handles.
Item Item
No. mm + mm lbs. pkg. No. Inch mm lbs. pkg.
281 16 2.5 2.5 .10 1 281 56 3/16 150 .11 1
281 17 3 3 .10 1 281 57 7/32 150 .11 1
281 18 4 4 .10 1 281 58 1/4 150 .11 1
281 19 5 5 .10 1 281 59 9/32 150 .12 1
281 20 6 6 .10 1 281 60 5/16 150 .13 1
281 61 11/32 150 .14 1
281 62 3/8 150 .15 1
281 63 7/16 150 .17 1
281 64 1/2 150 .18 1
281
Hex Metric Drive-Loc VI Interchangeable Blade
High alloy CVM steel, through hardened, hard chrome finish.
Over all blade length 150mm/5.9”. Blades fit all Drive-Loc VI handles.
Item 281 Drive-Loc VI Metric Nut Driver Blades
No. mm + mm lbs. pkg. High alloy CVM steel, through hardened, hard chrome finish.
281 49 2.0 2.5 .09 1 OAL blade length 150mm/5.9”. Blades fit all Drive-Loc VI handles.
281 50 3.0 4.0 .10 1 Item
281 51 5.0 6.0 .10 1 No. mm mm lbs. pkg.
281 68 4.0 150 .10 1
281 69 4.5 150 .10 1
281 70 5.0 150 .11 1
281 71 5.5 150 .11 1
281 72 6.0 150 .12 1
281 73 7.0 150 .13 1
281 74 8.0 150 .13 1
281 77 9.0 150 .14 1
281 75 10.0 150 .15 1
281 76 11.0 150 .20 1
281
Hex Inch Drive-Loc VI Interchangeable Blade
High alloy CVM steel, through hardened, hard chrome finish. Over all
blade length 150mm/5.9”. Blades fit all Drive-Loc VI handles.
Item
No. Inch + Inch lbs. pkg.
281 22 3/32 7/64 .10 1
281 23 1/8 9/64 .10 1
281 24 5/32 3/16 .10 1 281 44 Extension Blade For Drive-Loc VI Blades
High alloy CVM steel, through hardened, hard chrome finish.
OAL blade length 6.5”. Blades fit all Drive-Loc VI handles.
Item
No. mm OAL lbs. pkg.
281 44 6.0 165mm .14 1
Wiha Quality Tools
Germany
D
288 ESD Safe Interchangeable Blades For TorqueVario-S
tip blades on narrow 5/32 Hex shafts. High alloy chrome-
vanadium-molybdenum steel, hardened, hard chromed.
With Certificate Item Max. Torque
of Calibration No. Size mm mm lbs. Nm pkg.
+/- 6% 288 25 T5 175 4.0 .07 0.4 1
D
288 26 T6 175 4.0 .07 0.6 1
285 91 Set 24 Pcs. ESD Safe Adjustable TorqueVario-S Bit Set 288 27 T7 175 4.0 .07 0.9 1
Certified to EN ISO 6798, BS EN 26789, ASME B107.14M. Set 288 28 T8 175 4.0 .07 1.3 1
includes ergonomic multi-component adjustable TorqueVario-S handle, 288 29 T9 175 4.0 .07 2.5 1
21 Micro Bits, non-magnetic Micro Bit holder and Torque adjustment 288 30 T10 175 4.0 .07 3.8 1
tool, packed in a compact durable storage box.
Item No. Surface
285 91 Slotted: 1.5, 2.0, 3.0, 4.0mm lbs. resistance
Phillips: #00, #0, #1 1.31 of handle is
: T6, T7, T8, T9, T10, T15 106 - 109 Ohms
Hex Inch: .050, 1/16, 5/64, 3/32, 7/64, 1/8, 9/64, 5/32”
28524 Handle ESD Safe Range 5 - 10 Inch lbs.
Surface resistance of handle is 106 - 109 Ohms
With Certificate
285 92 Set 24 Pcs. ESD Safe Adjustable TorqueVario-S Bit Set of Calibration +/- 10%
D
Certified to EN ISO 6798, BS EN 26789, ASME B107.14M. Set
includes ergonomic multi-component adjustable TorqueVario-S handle, 288 90 Set 24 Piece TorqueVario-S ESD Safe Micro-Bit Set
21 Micro Bits, non-magnetic Micro Bit holder and Torque adjustment Certified to EN ISO 6798, BS EN 26789, ASME B107.14M. Set
tool, packed in a compact durable storage box. includes ergonomic multi-component adjustable TorqueVario-S handle,
Item No. 21 Micro Bits, non-magnetic Micro Bit holder and Torque adjustment tool.
285 92 Slotted: 1.5, 2.0, 3.0, 4.0mm lbs. Packed in a compact durable storage box.
Phillips: #00, #0, #1 1.31 Item No.
: T6, T7, T8, T9, T10, T15 288 90 Slotted: 1.5, 2.0, 3.0, 4.0mm Phillips: #00, #0, #1 lbs.
Hex Inch: .050, 1/16, 5/64, 3/32, 7/64, 1/8, 9/64, 5/32” : T6, T7, T8, T9, T10, T15 1.33
28526 Handle ESD Safe Range 7.5 - 20 Inch lbs. Hex Inch: .050, 1/16, 5/64, 3/32, 7/64, 1/8, 9/64, 5/32”
Surface resistance of handle is 106 - 109 Ohms 28522 ESD Safe Handle Range 15-80 Inch/oz.
Wiha Quality Tools
Germany
Wiha ESD Safe Pliers & Cutters Surface resistance of handles is 106 - 109 Ohms
Precision Cutters Tapered Head 327 03 Precision Cutters, Small Tapered Head, Semi Flush
Semi Flush Cutters drop-forged for an ideal material structure. Precise aligned
9.5mm
cutting edges are additionally induction hardened at a hardness of
Approx. 64OHRC. Two component non-slip soft grip handle,
ESD Safe Dissipative. ESD standard IEC 61340-5-1
7.5mm #327 03 mm Inch Copper Head Wdth Pkg. wt.
115 4.5 1.0 9.5mm 1 .19
115mm
D
Precision Cutters Tapered Head 327 05 Precision Cutters, Small Tapered Head, Flush
Flush Cutters drop-forged for an ideal material structure. Precise aligned
9.5mm cutting edges are additionally induction hardened at a hardness of
Precision Cutters Tapered Head 327 02 Precision Cutters, Small Tapered Head With Hollow
Semi Flush Ground Back, Semi Flush
9.5mm Cutters drop-forged for an ideal material structure. Precise aligned
cutting edges are additionally induction hardened at a hardness of
Approx. 64OHRC. Two component non-slip soft grip handle,
ESD Safe Dissipative. ESD standard IEC 61340-5-1
7.5mm
#327 02 mm Inch Copper Head Wdth Pkg. wt.
115mm 115 4.5 1.0 9.5mm 1 .19
D
Precision Cutters Tapered Head 327 04 Precision Cutters, Small Tapered Head With Hollow
Flush Ground Back, Flush
9.5mm Cutters drop-forged for an ideal material structure. Precise aligned
cutting edges are additionally induction hardened at a hardness of
Approx. 64OHRC. Two component non-slip soft grip handle,
ESD Safe Dissipative. ESD standard IEC 61340-5-1
6.0mm
#327 04 mm Inch Copper Head Wdth Pkg. wt.
D 115mm 115 4.5 1.0 9.5mm 1 .19
Wiha Quality Tools
Germany
Precision Cutters Wide Tapered Head 327 06 Precision Cutters, Wide Tapered Head, Bevel
Bevel Cutters drop-forged for an ideal material structure. Precise aligned
11.5mm
cutting edges are additionally induction hardened at a hardness of
Approx. 64OHRC. Two component non-slip soft grip handle,
ESD Safe Dissipative. ESD standard IEC 61340-5-1
7.5mm #327 06 mm Inch Copper Head Wdth Pkg. wt.
115 4.5 1.4 11.0mm 1 .20
115mm Surface resistance of handles is 106 - 109 Ohms
D
Precision Cutters Wide Tapered Head 327 08 Precision Cutters, Wide Tapered Head, Flush
Flush Cutters drop-forged for an ideal material structure. Precise aligned
11.0mm
cutting edges are additionally induction hardened at a hardness of
Approx. 64OHRC. Two component non-slip soft grip handle,
ESD Safe Dissipative. ESD standard IEC 61340-5-1
7.5mm #327 08 mm Inch Copper Head Wdth Pkg. wt.
115 4.5 1.2 11.0mm 1 .19
115mm Surface resistance of handles is 106 - 109 Ohms
D
Precision Cutters Wide Tapered Head 327 10 Precision Cutters, Wide Tapered Head, Full Flush
Cutters drop-forged for an ideal material structure. Precise aligned
Full Flush 11.0mm
cutting edges are additionally induction hardened at a hardness of
Approx. 64OHRC. Two component non-slip soft grip handle,
ESD Safe Dissipative. ESD standard IEC 61340-5-1
7.5mm #327 10 mm Inch Copper Head Wdth Pkg. wt.
115 4.5 1.0 11.0mm 1 .23
115mm Surface resistance of handles is 106 - 109 Ohms
D
Precision Cutters Wide Tapered Head 327 11 Precision Cutters, Wide Tapered Head With Wire Trapping
Device, Flush
Flush 11.5mm Cutters drop-forged for an ideal material structure. Precise aligned
cutting edges are additionally induction hardened at a hardness of
Approx. 64OHRC. Two component non-slip soft grip handle,
7.5mm ESD Safe Dissipative. ESD standard IEC 61340-5-1
#327 11 mm Inch Copper Head Wdth Pkg. wt.
(10.8mm)
w/wire 115 4.5 1.2 11.0mm 1 .19
115mm
D Surface resistance of handles is 106 - 109 Ohms
Precision Cutters Slim Oval Form 327 12 Precision Cutters, Slim Oval Head, Flush
Cutters drop-forged for an ideal material structure. Precise aligned
Flush 10.5mm cutting edges are additionally induction hardened at a hardness of
Approx. 64OHRC. Two component non-slip soft grip handle,
ESD Safe Dissipative. ESD standard IEC 61340-5-1
#327 12 mm Inch Copper Head Wdth Pkg. wt.
7.5mm
115 4.5 1.0 10.5mm 1 .23
115mm Surface resistance of handles is 106 - 109 Ohms
D
Wiha Quality Tools
Germany
Precision Cutters Slim Oval Form 327 14 Precision Cutters, Slim Oval Head, Full Flush
Full Flush Cutters drop-forged for an ideal material structure. Precise aligned
9.5mm cutting edges are additionally induction hardened at a hardness of
Precision Cutters Slim Oval Form 327 16 Precision Cutters, Wide Oval Head, Bevel
Bevel Cutters drop-forged for an ideal material structure. Precise aligned
11.5mm cutting edges are additionally induction hardened at a hardness of
Precision Cutters Wide Oval 327 18 Precision Cutters, Wide Oval Head Carbide
Form And Carbide Edge Cutting Edges, Bevel
11.0mm Cutters drop-forged for an ideal material structure. Precise aligned
Bevel carbide cutting edge. Two component non-slip soft grip handle,
ESD Safe Dissipative. ESD standard IEC 61340-5-1
#327 18 mm Inch Copper Head Wdth Pkg. wt.
7.5mm 110 4 3/8 1.6 11.0mm 1 .20
Surface resistance of handles is 106 - 109 Ohms
D 110mm
Precision Cutters Wide Oval Form 327 20 Precision Cutters, Wide Oval Head, Flush
Flush Cutters drop-forged for an ideal material structure. Precise aligned
11.5mm
cutting edges are additionally induction hardened at a hardness of
Approx. 64OHRC. Two component non-slip soft grip handle,
ESD Safe Dissipative. ESD standard IEC 61340-5-1
#327 20 mm Inch Copper Head Wdth Pkg. wt.
7.5mm
115 4.5 1.2 11.0mm 1 .19
115mm Surface resistance of handles is 106 - 109 Ohms
D
Precision Cutters Wide Oval Form 327 21 Precision Cutters, Wide Oval Head With Wire
Trapping Device, Flush
Flush 11.0mm
Cutters drop-forged for an ideal material structure. Precise aligned
cutting edges are additionally induction hardened at a hardness of
Approx. 64OHRC. Two component non-slip soft grip handle,
7.5mm ESD Safe Dissipative. ESD standard IEC 61340-5-1
#327 21 mm Inch Copper Head Wdth Pkg. wt.
D 115mm 115 4.5 1.2 11.0mm 1 .23
Surface resistance of handles is 106 - 109 Ohms
Wiha Quality Tools
Germany
Oblique Angled Cutters 327 24 Oblique Angled Cutters, 29O, Full Flush
Ultra Full Flush Oblique Cutters drop-forged for an ideal material structure. Precise
12.0mm
aligned cutting edges are additionally induction hardened at a hardness
of Approx. 64OHRC. Two component non-slip soft grip handle,
ESD Safe Dissipative. ESD standard IEC 61340-5-1
7.5mm #327 24 mm Inch Copper Head Wdth Pkg. wt.
115 4.5 1.0 12.0mm 1 .24
115mm
Surface resistance of handles is 106 - 109 Ohms
D
Oblique Angled Cutters 327 26 Oblique Angled Cutters, 29O, Short Head,
Semi Flush Semi Flush
12.0mm Oblique Cutters drop-forged for an ideal material structure. Precise
aligned cutting edges are additionally induction hardened at a hardness
of Approx. 64OHRC. Two component non-slip soft grip handle,
ESD Safe Dissipative. ESD standard IEC 61340-5-1
7.5mm #327 26 mm Inch Copper Head Wdth Pkg. wt.
115 4.5 1.2 12.0mm 1 .24
D 115mm
Surface resistance of handles is 106 - 109 Ohms
Oblique Front Cutters 327 28 Oblique Front Cutters, Very Small Head, 40O, Flush
Oblique Cutters drop-forged for an ideal material structure. Precise
Flush 9.7mm aligned cutting edges are additionally induction hardened at a hardness
of Approx. 64OHRC. Two component non-slip soft grip handle, ESD
Safe Dissipative. ESD standard IEC 61340-5-1
#327 28 mm Inch Copper Head Wdth Pkg. wt.
6.2mm 130 5.1 0.6 8.5mm 1 .21
130mm Surface resistance of handles is 106 - 109 Ohms
D
Tip Width
End Cutters Extra Slim 327 32 End Cutters, Extra Slim, Semi Flush
Semi Flush End Cutters drop-forged for an ideal material structure. Precise aligned
7.0mm
cutting edges are additionally induction hardened at a hardness of
Approx. 64OHRC. Two component non-slip soft grip handle,
ESD Safe Dissipative. ESD standard IEC 61340-5-1
2.9mm 6.0mm #327 32 mm Inch Copper Tip Wdth Pkg. wt.
130 5.1 0.6 4.1mm 1 .16
130mm Surface resistance of handles is 106 - 109 Ohms
D
End Cutters Wide Head 327 34 End Cutters, Wide Head, Flush
Flush End Cutters drop-forged for an ideal material structure. Precise aligned
11.5mm
cutting edges are additionally induction hardened at a hardness of
Approx. 64OHRC. Two component non-slip soft grip handle,
ESD Safe Dissipative. ESD standard IEC 61340-5-1
16.5mm 7.5mm
#327 34 mm Inch Copper Head Wdth Pkg. wt.
115 4.5 1.4 11.0mm 1 .18
115mm
D Surface resistance of handles is 106 - 109 Ohms
ESD Safe Pliers 327 42 ESD Safe Pliers, Short Snipe Nose (Chain Nose) Straight,
Short Snipe Nose Serrated Jaws
9.5mm Pliers drop-forged for an ideal material structure. Precisely aligned,
jaws, hardened. Two component non-slip soft grip handle,
D ESD Safe Dissipative. ESD standard IEC 61340-5-1
6.5mm #327 42 mm Inch Head Wdth Pkg. wt.
120 4 3/4 9.5mm 1 .20
120mm Surface resistance of handles is 106 - 109 Ohms
ESD Safe Pliers 327 44 ESD Safe Pliers, Snipe Nose (Chain Nose)
Bent Snipe Nose 45 O Bent 45O, Smooth Jaws
9.5mm Pliers drop-forged for an ideal material structure. Precisely aligned,
jaws, hardened. Two component non-slip soft grip handle,
ESD Safe Dissipative. ESD standard IEC 61340-5-1
D #327 44 mm Inch Head Wdth Pkg. wt.
6.5mm
120 4 3/4 9.5mm 1 .20
120mm Surface resistance of handles is 106 - 109 Ohms
ESD Safe Pliers 327 46 ESD Safe Pliers, Long Needle Nose Pliers, Straight,
Long Needle Nose Serrated Jaws
12.0mm Pliers drop-forged for an ideal material structure. Precisely aligned,
jaws, hardened. Two component non-slip soft grip handle,
D ESD Safe Dissipative. ESD standard IEC 61340-5-1
7.5mm #327 46 mm Inch Head Wdth Pkg. wt.
145 5 3/4 12.0mm 1 .27
Surface resistance of handles is 106 - 109 Ohms
145mm
Wiha Quality Tools
28 Toll Free: (800) 494-6104
ESD Safe Pliers 327 48 ESD Safe Pliers, Needle Nose Pliers, Bent 90O,
Smooth Jaws
Needle Nose, Bent 90O
Pliers drop-forged for an ideal material structure. Precisely aligned,
12.0mm
jaws, hardened. Two component non-slip soft grip handle,
ESD Safe Dissipative. ESD standard IEC 61340-5-1
D #327 48 mm Inch Head Wdth Pkg. wt.
7.5mm
145 5 3/4 12.0mm 1 .21
145mm Surface resistance of handles is 106 - 109 Ohms
ESD Safe Pliers 327 50 ESD Safe Pliers, Short Round Nose Pliers,
Smooth Jaws
Short Round
Pliers drop-forged for an ideal material structure. Precisely aligned,
Nose Pliers 9.5mm
jaws, hardened. Two component non-slip soft grip handle,
ESD Safe Dissipative. ESD standard IEC 61340-5-1
#327 50 mm Inch Head Wdth Pkg. wt.
6.5mm
120 4 3/4 9.5mm 1 .17
D 120mm
Surface resistance of handles is 106 - 109 Ohms
ESD Safe Pliers 327 52 ESD Safe Pliers, Short Flat Nose Pliers,
Short Flat Nose Smooth Jaws
9.5mm Pliers drop-forged for an ideal material structure. Precisely aligned,
Pliers
jaws, hardened. Two component non-slip soft grip handle,
ESD Safe Dissipative. ESD standard IEC 61340-5-1
6.5mm #327 52 mm Inch Head Wdth Pkg. wt.
D 120 4 3/4 9.5mm 1 .16
120mm Surface resistance of handles is 106 - 109 Ohms
Surface
resistance
of handles
ESD standard is 106 - 109
IEC 61340-5-1 Ohms
D
ESD standard
IEC 61340-5-1
11
327 91 Pc. Set, 4 ESD Safe Pliers, SYSTEM 4 Slotted & Phillips
5 Pc. Set & 2 ESD Safe Tweezers Pliers drop-forged for an ideal
D
material structure. Two component non-slip soft grip handle. ESD Safe
327 90
4 Pc. ESD Safe Pliers Set In Custom Case Precision handle & 4 CVM tool steel blades. Tweezers anti-static
Pliers drop-forged for an ideal material structure. Two component non- conductive, ESD Safe Hypo allergenic, anti-magnetic stainless.
slip soft grip handle. ESD Safe Dissipative. #327 91 11 piece ESD Safe Pliers, Tweezers & SYS 4 precision
#327 90 4 piece ESD Safe Pliers Set Set in custom case includes:
Set includes: ESD Safe Pliers & Cutters
32716 4.5” Oval Side Cutters 32746 5.75” Long Nose Pliers 32716 4.5” Oval Side Cutters 32746 5.75” Long Nose Pliers
32752 4.75” Flat Nose Pliers 32728 4.375” Oblique Cutters 32752 4.75” Flat Nose Pliers 32728 4.375” Oblique Cutters
lbs. 2.06 SYSTEM 4 Set in separate pouch
Surface resistance of handles is 106 - 109 Ohms 28000 ESD Safe Conductive Precision Handle
Slotted: 1.5, 2.0, 3.0 & 4.0 Phillips: 000, 00, 0 & 1
ESD Safe Tweezers: 44501 AA SA ESD & 44510 7a SA ESD
lbs. 2.43
Wiha Quality Tools
Toll Free: (800) 494-6104 29
turn
Wiha ESD Safe Proturn Pliers & Cutters Proturn available after December 15th 2009
NEW
pro
From Wiha Two component
handle with non-slip
soft grip surface,
protects the hand
and reduces manual
effort & user fatigue
Glare free
black finish
Hardened steel
return spring ESD standard
IEC 61340-5-1 D
Surface resistance of handles is 106 - 109 Ohms
ESD Safe Wire Stripper 458 10 Proturn ESD Safe Wire Stripper
pro turn
A ESD standard IEC 61340-5-1. C70 special tool steel. Glare free,
black finish. Two component handle with non-slip grips.
D B Strips 0.2, 0.3, 0.4, 0.5, 0.6, 0.8mm
#458 10 mm Inch Strips AWG A B C Pkg. wt.
165 6.5 30 to 20 30mm 12mm 4mm 1 .25
C
165mm
ESD Safe Long Nose Pliers 458 11 Proturn ESD Safe Long Nose Pliers
pro turn
B ESD standard IEC 61340-5-1. C70 special tool steel. Glare free,
black finish. Two component handle with non-slip grips.
D #458 11 mm Inch A B C Pkg. wt.
A 160 6.3 2mm 30mm 3mm 1 .18
C
160mm
ESD Safe Flat Nose Pliers 458 12 Proturn ESD Safe Flat Nose Pliers
pro turn
B ESD standard IEC 61340-5-1. C70 special tool steel. Glare free,
black finish. Two component handle with non-slip grips.
D #458 12 mm Inch A B C Pkg. wt.
A 160 6.3 2mm 32mm 3mm 1 .18
C
160mm
Wiha Quality Tools
30 Toll Free: (800) 494-6104
ESD Safe Bent Nose Pliers B 458 13 Proturn ESD Safe Bent Nose Pliers
pro turn
ESD standard IEC 61340-5-1. C70 special tool steel. Glare free,
black finish. Two component handle with non-slip grips.
D #458 13 mm Inch A B C Pkg. wt.
A 152 6.0 2mm 30mm 4mm 1 .18
C
152mm
ESD Safe Round Nose Pliers B 458 14 Proturn ESD Safe Round Nose Pliers
pro turn
ESD standard IEC 61340-5-1. C70 special tool steel. Glare free,
black finish. Two component handle with non-slip grips.
D #458 14 mm Inch A B C Pkg. wt.
A 152 6.0 2mm 22mm 3mm 1 .17
C
152mm
A
ESD Safe Diagonal Cutter B 458 20 Proturn ESD Safe 21° Precision Cutters/Flush Cut
pro turn
ESD standard IEC 61340-5-1. C70 special tool steel. Glare free,
black finish. Two component handle with non-slip grips.
D 21° Angle #458 20 mm Inch AWG A B C Pkg. wt.
127 5.0 18/1mm 13mm 12mm 3mm 1 .16
C
127mm
pro turn
ESD standard IEC 61340-5-1. C70 special tool steel. Glare free,
black finish. Two component handle with non-slip grips.
D 45° Angle #458 21 mm Inch AWG A B C Pkg. wt.
127 5.0 18/1mm 10mm 9mm 2mm 1 .14
C
127mm
pro turn
B
ESD standard IEC 61340-5-1. C70 special tool steel. Glare free,
black finish. Two component handle with non-slip grips.
D 21° Angle #458 22 mm Inch AWG A B C Pkg. wt.
140 5.5 16/1.3mm 13mm 12mm 3mm 1 .15
C
140mm
Wiha Quality Tools
Toll Free: (800) 494-6104 31
NEW
Wiha ESD Safe Proturn Pliers & Cutters
iha
From W Surface resistance of handles is 106 - 109 Ohms
ESD Safe Diagonal Cutter A 458 23 Proturn ESD Safe 21° Precision Cutters/Flush Cut
pro turn
B ESD standard IEC 61340-5-1. C70 special tool steel. Glare free,
black finish. Two component handle with non-slip grips.
D #458 23 mm Inch AWG A B C Pkg. wt.
21° Angle
133 5.25 14/1.6mm 10mm 10mm 2mm 1 .14
133mm C
pro turn
ESD standard IEC 61340-5-1. C70 special tool steel. Glare free,
black finish. Two component handle with non-slip grips.
D #458 24 mm Inch AWG A B C Pkg. wt.
45° Angle
140 5.5 14/1.6mm 13mm 12mm 2.5mm 1 .16
140mm C
26
458 90 Pc. Set, Proturn ESD Safe Pliers, Precision Slotted &
Flat Round Tip Smooth Sides Curved Extra Fine Rounded Tips
Item No. Description wt. Item No. Description wt.
445 05 2a SA ESD - 120mm .08 445 10 7a SA ESD - 120mm .08
Static dissipative, ESD Safe hypo allergenic tweezers made from Vommaloy. Static dissipative, ESD Safe hypo allergenic tweezers made from Vommaloy.
Special stainless steel, anti-magnetic and acid resistant. Special stainless steel, anti-magnetic and acid resistant.
Wiha Quality Tools
Germany
Holds 0.8 to 2mm Diameter Narrow Rounded Tip Serrated, Guide Pin
Item No. Description wt. Item No. Description wt.
445 11 50 SA ESD - 120mm .08 445 18 22 SA ESD - 150mm .10
Static dissipative, ESD Safe hypo allergenic tweezers made from Vommaloy. Static dissipative, ESD Safe hypo allergenic tweezers made from Vommaloy.
Special stainless steel, anti-magnetic and acid resistant. Special stainless steel, anti-magnetic and acid resistant.
Holds 6.5 to 10mm Diameter MicroTip For Chips Angled 1.6 x 1 x 1mm
Item No. Description wt. Item No. Description wt.
445 14 53 SA ESD - 120mm .08 445 22 13 SA ESD - 120mm .08
Static dissipative, ESD Safe hypo allergenic tweezers made from Vommaloy. Static dissipative, ESD Safe hypo allergenic tweezers made from Vommaloy.
Special stainless steel, anti-magnetic and acid resistant. Special stainless steel, anti-magnetic and acid resistant.
Flat Bent 35O, 3mm Diameter Grip MicroTip Bent 30O 1.6mm
Item No. Description wt. Item No. Description wt.
445 24 58 SA-SMD ESD - 117mm .08 445 29 8b SA ESD - 120mm .08
Static dissipative, ESD Safe hypo allergenic tweezers made from Vommaloy. Static dissipative, ESD Safe hypo allergenic tweezers made from Vommaloy.
Special stainless steel, anti-magnetic and acid resistant. Special stainless steel, anti-magnetic and acid resistant.
Curved Extra Fine, 3mm Long Straight Tip Flat Bent 35O, 2mm Diameter Grip Radius
Item No. Description wt. Item No. Description wt.
445 25 7abb SA ESD - 120mm .08 445 30 59 SA-SMD ESD - 117mm .08
Static dissipative, ESD Safe hypo allergenic tweezers made from Vommaloy. Static dissipative, ESD Safe hypo allergenic tweezers made from Vommaloy.
Special stainless steel, anti-magnetic and acid resistant. Special stainless steel, anti-magnetic and acid resistant.
Narrow Body Low Force Bent 35O-3mm Tip ESD Safe General Purpose Fine Point
Item No. Description wt. Item No. Description wt.
445 26 SSbb SA ESD - 140mm .08 445 31 1 SA ESD - 120mm .08
Static dissipative, ESD Safe hypo allergenic tweezers made from Vommaloy. Static dissipative, ESD Safe hypo allergenic tweezers made from Vommaloy.
Special stainless steel, anti-magnetic and acid resistant. Special stainless steel, anti-magnetic and acid resistant.
Item No. Page Item No. Page Item No. Page Item No. Page Item No. Page Item No. Page
To:
Static Dissipative