Documente Academic
Documente Profesional
Documente Cultură
2010
Recommended Citation
Mrozinski, Brent A., "Acetaldehyde scavengers for poly(ethylene terephthalate) : chemistry of reactions, capacity, and modeling of
interactions" (2010). Theses and Dissertations. 917.
http://utdr.utoledo.edu/theses-dissertations/917
This Dissertation is brought to you for free and open access by The University of Toledo Digital Repository. It has been accepted for inclusion in Theses
and Dissertations by an authorized administrator of The University of Toledo Digital Repository. For more information, please see the repository's
About page.
A Dissertation
entitled
by
Brent A. Mrozinski
by
Brent A. Mrozinski
the material may occur. One of the more common degradation products is acetaldehyde
(AA). Due to its low boiling point, 21oC, AA is able to diffuse out of PET and into either
the atmosphere or the packaged contents of the PET container. The diffusion of AA into
packaged contents is of concern, because many food products have a limited threshold for
the sweet, fruity taste and odor of AA. One of the ways to limit the AA affects is through
the addition of AA scavenging agents. While these additives do not limit the generation
of AA; they are designed to interact with and reduce the amount of AA that can be
The purpose of this study was not only to study these AA and AA scavenger interactions
and quantify their abilities in reducing AA concentrations in PET; it was also to develop
injection molding systems. Through this work, it was determined that anthranilamide and
iii
bonding/size-enclosing scheme. Regardless of the mechanism, it was proven that these
generally found that the greater the AA scavenger concentration, the great the effect.
Additionally, the changes in the physical properties of PET due to AA scavenger addition
were studied. It was shown that melt-blending these additives into PET could adversely
affect the intrinsic viscosity (I.V.) and color of the PET blend resin and/or container. The
thermal properties and oxygen permeation of PET were not affected by AA scavenger
addition.
account for the addition of AA scavengers, to PET resin, when predicting the
accumulation of AA within PET preforms. The approach to modify this original program
and methodologies to quantify the appropriate kinetic terms has been described in detail.
Finally, the modified simulation program was then used to predict the effectiveness of
preforms. While complete agreement between the modeling results and observed trends
from single-cavity injection molding was not achieved, the groundwork was laid to make
iv
To my wife, Whitney, you are the most important part of my life and I hope that I show
you the constant and unwavering love and support that you show me everyday. I look
forward to our journey together and all the joy it may bring.
To my mother, Nancy, thank you for too many things to list. Your love, guidance, and
friendship throughout these first 29 years of my life have been unimaginable. Thank you
for the tremendous examples of how to treat and respect others, how to be a parent, and
To my late father, Richard, who was not only a parent to me; he was also my best friend.
His tireless love, support, and encouragement still lives with me to this day. We shared
many great moments together: going up north to cut firewood, playing catch, watching
Detroit Tigers baseball games, and trying to teach him about golf; a sport for which he
had no interest except for the fact that it was important to me. His sudden passing on
December 19, 2006, following a short bout with cancer, left a tremendous void in my life
and heart. We were always very close, but those last 3 months were filled with moments
that I will never forget: many shared laughs, tears, and short walks through the house.
To quote a song from Keith Urban, “I only hope when I have my own family that
First and foremost, I would like to thank Dr. Saleh A. Jabarin for giving me this
tremendous opportunity to learn from him and conduct this research project at the
Polymer Institute, under his guidance. His knowledge, encouragement, and incredible
patience have been not only appreciated, but greatly needed as well.
I would like to thank Dr. Mike Cameron for his help with the computational modeling
work and Mrs. Elizabeth Lofgren for her help with the various analytical experiments and
for reviewing this work. The generosity of their time and effort has been immensely
appreciated. Thank you to Mr. Mike Mumford for his help with the processing
equipment and experiments and to Mrs. Jackie Zydorczyk for her support and help.
Thank you to my fellow students at the Polymer Institute for your encouragement and
Kim, and Dr. Kamal Mahajan for their assistance in conducting experiments. Thank you,
as well, to the PET Industrial Consortium for their financial support for this work.
I would like to thank Dr. Dong-Shik Kim, Dr. Yong-Wah Kim, Dr. Steven E. LeBlanc,
A final thank you is extended to my wife, my mother, and my entire family for their
vi
Contents
Abstract iii
Acknowledgments vi
Contents vii
1 Introduction 1
1.4.1 Overview...................................................................................................11
vii
1.4.2 Amount of Acetaldehyde in PET..............................................................12
2 Literature Review 25
viii
2.4.2 Size-Enclosing AA Scavengers ................................................................39
2.4.2.1 Cyclodextrins...............................................................................39
3 Experimental Work 47
3.4.2 Stretch-Blow-Molding..............................................................................61
ix
3.6.1 Plate and Plate Rheometer ........................................................................69
Samples .....................................................................................120
Samples .....................................................................................125
x
4.3.2 Color .......................................................................................................126
4.3.3.2 Crystallization Behavior When Heating from the Glassy State 132
4.5 Modeling............................................................................................................144
xi
5.1.2 Effectiveness of AA Scavengers’ Apparent Reduction in Generated
AA ..........................................................................................................194
5.1.5 Modeling.................................................................................................201
References 206
1
A H NMR Spectra of AA and Alpha-Cyclodextrin Titration Experiment 220
K Data Used to Determine the k1, bb1, bb2, and b Values 289
xii
List of Figures
1-4 Reaction Scheme for the Polymerization of BHET to Produce PET and EG............4
1-11 AA Formation from Vinyl Ester End-Groups Reacting with Hydroxyl End-
xiii
2-5 Various Forms of Cyclodextrin................................................................................40
4-6 Predicted 1H NMR Spectrum for the Product Formed from the Proposed
4-8 Predicted 1H NMR Spectrum for the Product Formed from the Proposed
4-10 ESI Mass Spectrum of the Product from the Reaction Between Anthranilamide
4-12 Predicted 1H NMR Spectrum for the Product Formed from the Proposed Reaction
xiv
4-13 1H NMR Spectrum of MXDA in CDCl3 ..................................................................94
4-15 1H NMR Spectrum of the Reaction Between MXDA and AA in CDCl3 ................97
4-22 Peak Shifting of the Protons for AA and its Equilibrium Product When Titrated
4-30 DSC Cooling Curve of the 2.5 Weight % Alpha-Cyclodextrin/PET Blend ..........131
4-31 Viscosity versus Shear Rate Curves for the Voridian CB12 PET Resin ...............149
4-32 Arrhenius Plot for the Voridian CB12 PET Resin .................................................151
4-33 Temperature Profile as a Function of Radial Distance from the Center of a Flow
xv
4-34 Distribution of AA as a Function of Radial Distance from the Center of the Flow
Channel...................................................................................................................154
4-35 Distribution of Material to Fill Four Cavities within an Eight-Cavity Mold .........155
4-36 Temperatures for the Various Cavities as a Function of Filling Times .................156
Blend .....................................................................................................................167
Blend ......................................................................................................................168
4-39 60 Minute AA Generation Curve for the 10,000 ppm MXDA/PET Blend ...........168
d[AA]
4-40 Plot of ln( RG − ) Versus ln([AA]) for the 10,000 ppm
dt
d[AA]
4-41 Plot of ln( RG − ) Versus ln([AA]) for the 10,000 ppm Alpha-
dt
d[AA]
4-42 Plot of ln( RG − ) Versus ln([AA]) for the 10,000 ppm MXDA/PET
dt
4-45 60 Minute AA Generation Data for the 10,000 ppm MXDA/PET Blend Fitted
xvi
4-46 60 Minute AA Generation Data for the 10,000 ppm Anthranilamide/PET
Blend Fitted with Equation 17; Using the a, k1 at 290oC, and b Values ................177
Blend Fitted with Equation 17; Using the a, k1 at 290oC, and b Values ................177
4-48 60 Minute AA Generation Data for the 10,000 ppm MXDA/PET Blend Fitted
Blend Fitted with Equation 17; Using the a, b, and bb2 Values and the 2nd
Blend Fitted with Equation 17; Using the a, b, and bb2 Values and the 2nd
4-51 60 Minute AA Generation Data for the 10,000 ppm MXDA/PET Blend Fitted
with Equation 17; Using the a, b, and bb2 Values and the 2nd Iteration bb1
Value ......................................................................................................................181
4-54 Predicted Injection Molding Results for Various MXDA/PET Blends and for
xvii
4-57 One Minute Simulated AA Generation at 300oC ...................................................186
Process....................................................................................................................188
4-60 Predicted Injection Molding Results for Various MXDA/PET Blends, Studied
C-1 AA Generation Plots for the Voridian CB12 PET Resin .......................................248
C-3 AA Generation Plots for the “Two-Times” Processed PET Sample .....................249
C-4 AA Generation Plots for the “Three-Times” Processed PET Sample ...................250
C-5 AA Generation Plots for the 10,000 ppm Anthranilamide/PET Blend Sample.....250
C-6 AA Generation Plots for the 500 ppm Anthranilamide/PET Blend Sample..........251
Sample....................................................................................................................251
xviii
C-8 AA Generation Plots for the 100 ppm Anthranilamide/PET Blend Sample..........252
Sample....................................................................................................................252
Sample....................................................................................................................253
Sample....................................................................................................................253
C-12 AA Generation Plots for the 5000 ppm Alpha-Cyclodextrin/PET Blend Sample .254
C-13 AA Generation Plots for the 1200 ppm Alpha-Cyclodextrin/PET Blend Sample .254
C-14 AA Generation Plots for the 500 ppm Alpha-Cyclodextrin/PET Blend Sample ...255
C-15 AA Generation Plots for the 10,000 ppm MXDA Blend Sample..........................255
C-16 AA Generation Plots for the 1200 ppm MXDA Blend Sample .............................256
C-17 AA Generation Plots for the 500 ppm MXDA Blend Sample ...............................256
C-18 AA Generation Plots for the 200 ppm MXDA Blend Sample ...............................257
C-19 AA Generation Plots for the 100 ppm MXDA Blend Sample ...............................257
D-2 Arrhenius Plot for the “Two-Time” Processed PET Sample .................................260
D-3 Arrhenius Plot for the “Three-Time” Processed PET Sample ...............................260
D-4 Arrhenius Plot for the 10,000 ppm Anthranilamide/PET Blend Sample...............261
D-5 Arrhenius Plot for the 1200 ppm Anthranilamide/PET Blend Sample..................261
D-6 Arrhenius Plot for the 500 ppm Anthranilamide/PET Blend Sample ....................262
D-7 Arrhenius Plot for the 200 ppm Anthranilamide/PET Blend Sample ....................262
D-8 Arrhenius Plot for the 100 ppm Anthranilamide/PET Blend Sample ....................263
xix
D-9 Arrhenius Plot for the 50,000 ppm Alpha-Cyclodextrin/PET Blend Sample ........263
D-10 Arrhenius Plot for the 25,000 ppm Alpha-Cyclodextrin/PET Blend Sample ........264
D-11 Arrhenius Plot for the 10,000 ppm Alpha-Cyclodextrin/PET Blend Sample ........264
D-12 Arrhenius Plot for the 5000 ppm Alpha-Cyclodextrin/PET Blend Sample ...........265
D-13 Arrhenius Plot for the 1200 ppm Alpha-Cyclodextrin/PET Blend Sample ...........265
D-14 Arrhenius Plot for the 500 ppm Alpha-Cyclodextrin/PET Blend Sample .............266
D-15 Arrhenius Plot for the 1200 ppm MXDA/PET Blend Sample...............................266
D-16 Arrhenius Plot for the 500 ppm MXDA/PET Blend Sample.................................267
D-17 Arrhenius Plot for the 200 ppm MXDA/PET Blend Sample.................................267
D-18 Arrhenius Plot for the 100 ppm MXDA/PET Blend Sample.................................268
xx
List of Tables
4.3 Peak Assignment for the 1H NMR Spectrum of the Reaction Between
4.4 Peak Assignment for the 1H NMR Spectrum of MXDA in CDCl3 .........................94
xxi
4.5 Peak Assignment for the 1H NMR Spectrum of the Reaction Between MXDA
4.6 Peak Assignment for the 1H NMR Spectrum of Alpha-Cyclodextrin in D2O .......100
4.13 Comparison of the Residual AA Data for Pelletized and Preform Samples ..........120
4.16 Comparison of the I.V. Data for Pelletized and Preform Samples ........................125
4.19 Crystallization Behavior Data When Heating from the Glassy State ....................133
4.20 Melting Behavior Data When Heating from the Glassy State ...............................134
4.21 Crystallization Behavior Data When Cooling form the Melt ................................135
xxii
4.29 Explanation of the Terms in Equation 16...............................................................152
4.37 Calculated k2, for 290oC, and a Value for Each Scavenging Agent.......................172
4.38 b, bb1, and bb2 Values for Each Scavenging Agent Determined Through
4.39 Final a, b, bb1, bb2, and k1 Values for Each AA Scavenging Agent ......................182
A.1 Location of the AA and Alpha-Cyclodextrin Protons for each of the AA and
A.2 Change in Location of the Protons Representing AA and its D2O Equilibrium
B.1 AA Generation Data for the Voridian CB12 PET Resin .......................................228
B.2 AA Generation Data for the “One-Time” Processed PET Sample ........................229
B.3 AA Generation Data for the “Two-Times” Processed PET Sample ......................230
B.4 AA Generation Data for the “Three-Times” Processed PET Sample ....................231
B.5 AA Generation Data for the 10,000 ppm Anthranilamide/PET Blend Sample .....232
B.6 AA Generation Data for the 1200 ppm Anthranilamide/PET Blend Sample ........233
B.7 AA Generation Data for the 500 ppm Anthranilamide/PET Blend Sample ..........234
B.8 AA Generation Data for the 200 ppm Anthranilamide/PET Blend Sample ..........235
xxiii
B.9 AA Generation Data for the 100 ppm Anthranilamide/PET Blend Sample ..........236
Sample....................................................................................................................237
Sample....................................................................................................................238
Sample....................................................................................................................239
B.13 AA Generation Data for the 5000 ppm Alpha-Cyclodextrin/PET Blend Sample .240
B.14 AA Generation Data for the 1200 ppm Alpha-Cyclodextrin/PET Blend Sample .241
B.15 AA Generation Data for the 500 ppm Alpha-Cyclodextrin/PET Blend Sample ...242
B.16 AA Generation Data for the 10,000 ppm MXDA/PET Blend Sample ..................243
B.17 AA Generation Data for the 1200 ppm MXDA/PET Blend Sample .....................244
B.18 AA Generation Data for the 500 ppm MXDA/PET Blend Sample .......................245
B.19 AA Generation Data for the 200 ppm MXDA/PET Blend Sample .......................246
B.20 AA Generation Data for the 100 ppm MXDA/PET Blend Sample .......................247
E.1 Residual AA Data for the Control PET Pelletized Samples ..................................269
E.3 Residual AA Data for the Alpha-Cyclodextrin/PET Blend Pelletized Samples ....270
E.5 Residual AA Data for the PET Control Preform Samples .....................................270
E.6 Residual AA Data for the Anthranilamide/PET Blend Preform Samples .............271
E.8 Residual AA Data for the MXDA/PET Blend Preform Samples ..........................272
xxiv
F.1 Melt Viscosity Data for the Control PET Pelletized Samples................................273
F.2 Melt Viscosity Data for the Anthranilamide/PET Blend Pelletized Samples ........273
F.3 Melt Viscosity Data for the Alpha-Cyclodextrin/PET Blend Pelletized Samples .274
F.4 Melt Viscosity Data for the MXDA/PET Blend Pelletized Samples.....................274
F.5 Melt Viscosity Data for the Control PET Preform Samples ..................................274
F.6 Melt Viscosity Data for the Anthranilamide/PET Blend Preform Samples...........275
F.7 Melt Viscosity Data for the Alpha-Cyclodextrin/PET Blend Preform Samples....275
F.8 Melt Viscosity Data for the MXDA/PET Blend Preform Samples .......................276
G.1 Color Data for the Voridian CB12 PET Control Samples .....................................277
I.2 AA Generation Data for the 10,000 ppm Anthranilamide/PET Blend ..................284
I.3 AA Generation Data for the 10,000 ppm Alpha-Cyclodextrin/PET Blend ...........285
I.4 AA Generation Data for the 10,000 ppm MXDA/PET Blend ...............................286
J.1 Calculated Data Based on 60 Minute AA Generation Data, at 290oC, for the
J.2 Calculated Data Based on 60 Minute AA Generation Data, at 290oC, for the
J.3 Calculated Data Based on 60 Minute AA Generation Data, at 290oC, for the
xxv
K.1 Anthranilamide/PET Blend Data, at 280oC, Calculated for the Original ln(k2)
K.2 Anthranilamide/PET Blend Data, at 290oC, Calculated for the Original ln(k2)
K.3 Anthranilamide/PET Blend Data, at 300oC, Calculated for the Original ln(k2)
K.7 MXDA/PET Blend Data, at 280oC, Calculated for the Original ln(k2) Versus
K.8 MXDA/PET Blend Data, at 290oC, Calculated for the Original ln(k2) Versus
K.9 MXDA/PET Blend Data, at 300oC, Calculated for the Original ln(k2) Versus
K.10 Multiple Linear Regression Data Used to Determine the b, bb1, and bb2 Values
K.11 Multiple Linear Regression Data Used to Determine the b, bb1, and bb2 Values
xxvi
K.12 Multiple Linear Regression Data Used to Determine the b, bb1, and bb2
Modeled at 280oC...................................................................................................300
Modeled at 280oC...................................................................................................301
Modeled at 280oC...................................................................................................302
Modeled at 280oC...................................................................................................303
Modeled at 270oC...................................................................................................304
Modeled at 290oC...................................................................................................305
Modeled at 300oC...................................................................................................306
xxvii
Chapter 1
Introduction
for its optical, mechanical, and thermal properties. The combination of these properties
makes PET applicable to many industries for a variety of uses.1 Some of the more
• synthetic fiber to manufacture both apparel and carpets for the textile industry
1
For many packaging applications PET is a preferred material. When PET is properly
oriented it provides good optical transparency, high impact strength, and good gas barrier
carbon dioxide and water vapor.1, 2 Over the past twenty-five years PET has become the
leading packaging material for carbonated soft drinks, sports drinks, and water.
Depending on the final use, the molecular weight of the PET resin may vary. It is a
common practice within the industry to identify PET samples by their respective intrinsic
viscosities (I.V.) rather than their molecular weights.4 Table 1.1 shows typical I.V.
As shown in Table 1.1, the I.V., or molecular weight, of PET can vary depending on its
techniques can vary depending on the I.V. that is desired. To date, there are three
important to choose the right technique because each has its own benefits and drawbacks.
2
1.2.1 Melt-Phase Polymerization
terephthalate (DMT), both can be classified as di-acids. When TPA is used, a self-
O O
HO
HO O
HO
+ 2
+ 2 H2O
O O
OH
O OH
OH
TPA EG BHET Water
Figure 1-2: Reaction scheme for TPA and EG to produce BHET
acetaldehyde (AA), a byproduct.1, 3 Some of the common catalysts used for this reaction
include acetates of lithium (Li), calcium (Ca), magnesium (Mg), zinc (Zn), or lead (Pb);
3
CH3 HO O
O O
HO
+ 2
+ 2
CH3
O H
OH O O
O O
CH3
OH
DMT EG BHET AA
Figure 1-3: Reaction scheme for DMT and EG to produce BHET
Once BHET is produced, either from EG and TPA or EG and DMT, it must be
reaction and thus the byproduct, ethylene glycol (EG), must be removed to obtain a high
yield of PET.4 The catalysts for this reaction include acetates of antimony (Sb), Zn, or
O O
HO
O
HO
HO
n O
O
O
H
+ n
O O
n
O OH
OH
BHET PET EG
Figure 1-4: Reaction scheme for the polymerization of BHET to produce PET and EG
4
Traditional melt-phase polymerization techniques have a limit to the molecular weight, or
I.V., that can be achieved.1, 3, 4 The constraint is due to the difficulty in removing the
reaction by-products (particularly EG), BHET, and oligomers from the viscous PET
equilibrium reaction forward and thus continually increase the degree of polymerization
used as textile or as film or tape.1, 4 The desired I.V. for these applications is achievable
with melt-phase polymerization alone. When higher I.V. PET is needed to manufacture
containers or tire cord, for example, the I.V. needs to be increased beyond what melt-
second polymerization technique was required to produce higher I.V. PET. This second
molecular weight (or I.V.) by driving the various PET end-groups to react with one
another and thus increasing the length of the polymer chains.1, 3, 4 As the end-groups
react with one another, by-products are formed. Removal of these by-products (water,
EG, AA, etc.) is achieved by continual inert gas purging or by applying vacuum
progress the SSP equilibrium reactions forward and ultimately reach the desired I.V.
5
During the SSP process, solid PET pellets are heated well above the polymer’s glass
transition temperature (Tg) but below its melting temperature. This temperature range is
typically between 200 and 240oC.1 As the temperature is increased, mobility of the
polymer chains also increases. This increases the likelihood/ability of the polymer
chains’ end-groups to find and react with one another. If the temperature is excessively
increased, however, thermal degradation can occur; causing random chain scission to
occur.1, 3 Random chain scission leads to the formation of low molecular weight by-
products and the loss of molecular weight from the PET chains. The thermal degradation
is typically performed between 270 and 285oC; which is above the melting temperature
of PET, usually listed to be above 255oC. SSP, however, is carried out at a much milder
temperature range; between 200 and 240oC. Therefore, at SSP conditions PET is in a
solid, rubbery state and not the viscous liquid seen during melt-phase polymerization.
This makes it much easier for a purging gas (or vacuum) to remove the volatile
degradation products and reaction by-products that form during polymerization.1 The
greater ease of by-product removal allows the polymerization process to progress beyond
the limitation observed during melt-phase polymerization. Additionally, the milder SSP
reaction temperature causes fewer side reactions to occur.1, 3 The combination of less
side reactions and easier by-product removal create a more efficient route for the end-
6
groups of PET to react with one another and ultimately for the molecular weigh to
by solid-state polymerization) has been the traditional method to achieve high molecular,
or high I.V., PET resins. In recent years, however, new melt-phase polymerization
techniques5-12 have been developed that are now able to produce high molecular weight
PET resins without the need for solid-state polymerization. This technology has
especially become prevalent when producing PET resins to be used in the manufacturing
of containers. These new processes use the same starting materials (EG and TPA or EG
and DMT) and follow the same chemistry as the traditional two-step method (Figures 1-2
to 1-4).
The appeal of these new melt-phase polymerization methods are believed to reduce the
overall cost of production. Not only does SSP require additional reactors and energy to
run the process, it is also a time consuming operation. Elimination of the SSP step would,
Elimination of the SSP step, however, may need to be carefully considered. The inherent
advantages of SSP, as previously discussed, are something that could be critical to the
final product. Traditional solid-state polymerized PET resins possess minimal unwanted
7
by-products and good thermal stability; criteria which one-step polymerization
There are applications where it is desirable to slightly alter the physical properties of
poly(ethylene terephthalate) in order to better meet the needs of its end-use. To do this,
homopolymer.
original raw materials (EG, TPA, or DMT) with another reactant(s). The copolymer
concentration in the final product is typically less than 10%. Cyclohexane dimethanol
(CHDM) and isophthalic acid (IPA) are two of the more common reactants used as
substitutes to create PET copolymer resins.3, 4 When compared to EG, the increased size
of CHDM alters the structured packing of the polymer chains. This phenomenon affects
the resin’s crystallinity and therefore lowers its melting point.4 The carboxyl end-groups
of TPA are in a 1, 4 (“para”) configuration, where as the carboxyl end-groups of IPA are
polymer chain. This again alters the resin’s crystallinity and thus its melting point.4 The
chemical structures of CHDM and IPA are shown in Figure 1-5 and 1-6, respectively.
8
OH
HO
Figure 1-5: Chemical structure of cyclohexane 1, 4 dimethanol (CHDM)
O OH
OH
Figure 1-6: Chemical structure of isophthalic acid (IPA)
The melting and processing of PET resin into manufactured articles frequently results in
at least some degradation of the material.1, 3, 4 During the extrusion or injection molding
process the polymer can be subjected to moisture, oxygen, and/or elevated temperatures.
Each of these can cause at least one route of degradation. There are three main
degradation processes that can occur during PET processing: hydrolytic degradation,
Hydrolytic degradation occurs when of water reacts with PET at elevated temperatures.
This reaction can result in the reduction of I.V. or molecular weight; resulting in the
9
material and thus it will to absorb moisture from the atmosphere.1, 3 To limit the effects
of hydrolytic degradation, PET must be properly dried prior to processing the material. It
is generally observed that PET should contain less than 50 parts per million (ppm) of
Thermal degradation occurs when PET is exposed to high temperatures. This results in
random chain scission, forming carboxyl and vinyl ester end-groups.13, 14 The formation
temperature, the residence time, and the shear heating that occurs during extrusion or
injection molding.15
be melted and/or processed under vacuum or in an inert environment. For example, the
10
oxygen within the headspace of an extruder can be flushed by means of a nitrogen purge
or a vacuum.
1.4.1 Overview
One of the more common byproducts resulting from the degradation of PET is
including citrus fruits, bread, wine, and milk. 2, 18 AA is known to have a sweet, fruity
taste and odor.2, 18, 19 This small organic compound, shown in Figure 1-7, is also very
CH3
O H
Figure 1-7: Chemical structure of acetaldehyde
The presence of acetaldehyde within PET packages has been known to result in adverse
effects.2, 20 With a boiling point that is lower than room temperature, AA is able to
diffuse out of PET and into either the atmosphere or into the packaged contents. The
diffusion of AA into packaged contents is a concern because many food products have a
limited threshold for the taste of acetaldehyde. This is especially true when bottling
11
water because the taste of pure water is so sensitive that even a small amount of AA is
detectable by consumers.21
The amount of acetaldehyde that is present within PET varies greatly during the
PET resin of relatively low I.V., typically around 0.60 dL/g, which possesses a high
amount of AA. It is not uncommon for this resin to contain more than 20 ppm of AA.
To reduce the amount of degradation byproducts and prepare the PET resin for the
second polymerization step, the amorphous resin is subsequently dried and crystallized.
polymerize the PET resin and increase its I.V. Inherent to the SSP process, degradation
byproducts, such as AA, are removed from the polymer’s matrix. SSP can reduce the AA
concentration from less than 15 ppm to less than 3 ppm. Additional drying of the solid-
state polymerized PET resin can ultimately yield an AA concentration of less than 1 ppm.
The final step is to use this PET resin to manufacture articles for consumers to use. For
instance, preforms can be injection molded. These preforms will ultimately be stretch-
12
blow-molded into food or beverage containers. The melting and processing that occurs
during injection molding results in some PET degradation; increasing the AA content to
around 10 ppm or less. It is this 10 ppm of AA that is of concern to the PET container
manufacturers for foods and beverages. If an excessive amount of AA migrates from the
PET container to the packaged contents, the taste of the packaged product could be
undesirably altered. Figure 1-8 shows a graphical depiction of this example, showing
SSP
[≤ 10 ppm]
Figure 1-8: Acetaldehyde concentration during the lifecycle of PET
There are several identified PET degradation routes that result in the generation of
acetaldehyde. These AA producing chemical reactions result from two of the three core
13
degradation.1, 3 The factors that drive these reactions are: temperature, hydroxyl end-
groups, diethylene glycol (DEG) molecules, vinyl ester end-groups, oxygen, DEG
The chemical reaction in Figure 1-9 shows the thermal decomposition of hydroxyl end-
reaction are the presence of hydroxyl end-groups and elevated temperature. Therefore,
Figure 1-10 shows how acetaldehyde can be generated from diethylene glycol
react to form a larger PET chain that is connected by an anhydride linkage. Also
produced in this reaction is a DEG molecule. This DEG molecule can then undergo a
dehydration reaction to produce ethylene oxide vinyl ether and water. The ethylene
glycol vinyl ether molecule can subsequently decompose to produce two molecules of
acetaldehyde.
14
Figure 1-10: AA formation from diethylene glycol (DEG) molecules
Of all the factors that lead toward the generation of AA, researchers3, 22, 23 have shown
that the most prominent is the concentration of vinyl ester end-groups in PET. Vinyl
ester end-groups typically form during a random chain scission reaction; as illustrated in
thermal degradation.
Once the vinyl ester end-group is formed, it can generate AA by two different
mechanisms. The first route is by reacting with another PET chain terminated by a
hydroxyl end-group. This reaction creates a larger PET chain, connected by an ethylene
linkage, and a molecule of acetaldehyde. The second route occurs when the vinyl ester
end-group reacts with a carboxyl end-group. This reaction ultimately yields a larger PET
15
Figure 1-11: AA Formation from vinyl ester end-groups reacting with hydroxyl end-
groups and carboxyl end-groups
Not only can vinyl ester end-groups form by random chain scission and thermal
that is present during the melting and processing of PET can react with the ethylene
group may then decompose to form free radicals. As illustrated in Figure 1-12, these free
radicals will eventually yield two PET chains, one terminated by a vinyl ester end-group
and one terminated by a hydroxyl end-group. As previously shown in Figure 1-11, these
functional groups will react with one another to yield a larger PET chain and a molecule
of acetaldehyde.
16
Figure 1-12: AA generation due to the presence of oxygen
The process for synthesizing PET, melt-phase polymerization, is usually carried out
between 270 to 285oC. At these elevated temperatures, it is common for a small amount
of ethylene glycol (EG) to react with itself to form diethylene glycol (DEG). Since EG
and DEG are both diols, it is possible for DEG to replace EG during the synthesis of the
PET chains. When this occurs, a DEG linkage connects the terephthalate groups of PET
17
rather than an EG linkage. The disadvantage of this linkage, however, is that it is
When oxygen attacks the DEG linkage it forms a branched hydroperoxide group; similar
to the one formed in Figure 1-12. With elevated temperature, this hydroperoxide group
decomposes to form free radicals. In time, these free radicals lead to the formation of
PET chains terminated by vinyl ester end-groups and hydroxyl end-groups. As shown in
18
Figures 1-11, 1-12, and 1-13; ultimately the reaction of vinyl ester end-groups and
Figures 1-12 and 1-13 have shown how the presence of oxygen can lead to the generation
of free radicals and eventually AA.3, 4 Figure 1-14 also shows a degradation reaction
scheme that results from the presence of a free radical. This time, however, the free
radical is generic and could have been produced by another mechanism; such as the
When the free radical reacts with PET, as shown in Figure 1-14, it shifts from the generic
species to the ethylene portion of the PET chain. The instability of the free radical causes
the chain to split in two, forming a PET chain terminated by a vinyl ester end-group and a
1-14, the presence of the unstable end-group and the presence of the vinyl ester end-
19
Figure 1-14: AA generation due to the presence of free radicals
As previously mentioned in Sections 1.4.1 and 1.4.2, the amount of AA in PET is of great
generated during manufacturing can, with time, diffuse from the PET container and into
the packaged contents. It is known that an excessive amount of acetaldehyde can affect
the desired taste of many food products.2, 20 The most extreme scenario exists for bottled
20
water distributors. The taste of pure water is very subtle and is unable to mask the taste
There are a few common techniques that manufacturers use to limit the generation of AA
for PET packages. The first solution is to optimize the processing conditions. This
includes minimizing the melt temperature, shear rate, and residence time that the polymer
temperature and amount of time the polymer is exposed to these harsh conditions.
Of all the AA producing degradation mechanisms discussed in Sections 1.3 and 1.4.3,
thermal degradation has the greatest impact on the generation of AA. Thermal
degradation leads to random chain scission reactions, resulting in the formation of vinyl
concentration has been shown to have the most direct influence on the amount of AA that
will be generated.23
sometimes referred to as “water-grade” resins. These are resins which have been
manufacturing.
21
There are instances, however, where acetaldehyde levels are required to be lower than
called AA scavengers can be melt-blended into the PET matrix. These additives do not
limit the degradation of PET or the generation of AA; acetaldehyde scavengers work by
prepared his samples by dry-blending each scavenging agent with PET pellets and then
thermally pressing those blends into films. Each film was stored in its own aqueous
aldehyde, within each solution, over time. Suloff24 showed that aldehyde
control films. He also showed that the scavenging agents preferred smaller molecular
Suloff’s work24 examined the ability of his thermally pressed scavenging agent/PET
blend films to remove aldehydes from an aqueous solution. The purpose of the current
research project is to expand upon Suloff’s work, while focusing solely on acetaldehyde
22
overall effects of melt-blending AA scavengers into poly(ethylene terephthalate).
Through this research an understanding of the influence that the AA scavengers have
upon the physical properties of PET will also be developed. These physical properties
include: thermal properties, thermal stability, intrinsic viscosity (I.V.), barrier properties,
Through the knowledge obtained by studying the interactions that occurs between
acetaldehyde scavengers and PET, a greater understanding will be achieved and the
sequestering systems. It is also through this research that an initial model will be
developed for a multi-cavity injection molding system. This model will be used to
determine the amount of AA scavengers that will be needed to melt-blend with PET in
To meet these goals, the following five objectives have been identified as the focal points
of this work:
23
3. Study any changes in the physical properties of PET due to the addition of the AA
scavengers.
scavengers.
24
Chapter 2
Literature Review
There has been a significant amount of research focusing on reducing the presence of
acetaldehyde (AA) in PET. The majority of this work has concentrated on the
1.4.3, thermal degradation and thermal-oxidative degradation both lead to the generation
of AA.1, 3 Thermal degradation and thermal-oxidative degradation are two of the three
main degradation routes of PET. Hydrolytic degradation, the last of the three main PET
degradation routes, does not directly lead to the formation of AA. In fact, research has
shown that the presence of water during PET processing actually reduces the amount of
AA that is generated.1
As previously stated in Section 1.3.2, thermal degradation of PET occurs when the
these extreme conditions results in random chain scission reactions. Marshall and Todd25
25
believed these reactions occurred at the end of the polymer chains. Both Goodings17 and
Ritchie26 felt that thermal degradation reactions occur at the ester linkages. Although the
true location of this degradation mechanism may be of debate, it is agreed that random
chain scission reactions lead to the generation of additional carboxyl and vinyl ester end-
groups.
Thermal degradation is known to have several other effects upon PET besides the
generation of additional carboxyl and vinyl ester end-groups. With the addition of these
generated end-groups comes a reduction in the polymer’s molecular weight and intrinsic
viscosity (I.V.). Thermal degradation has also been known to cause discoloration within
the polymer, as well as the formation of oligomers and low molecular weight
byproducts.1, 3
One of the low molecular weight byproducts that are formed through the thermal
degradation of PET is acetaldehyde. AA has been shown to be the most prominent of all
determined that AA comprises 80% of all the generated, gaseous byproducts. During
ester end-groups.23 As illustrated in Figure 1-11, in Section 1.4.3.3, the vinyl ester end-
group can generate AA by reacting with either a carboxyl end-group or a hydroxyl end-
group.
26
Shukla, et al15 performed an exhaustive study examining the effects that various injection
molding parameters can have on the degradation of PET and the generation of AA. Their
work revealed that increasing the processing temperature by 10oC will cause the AA
concentration within PET to double. In addition, Shukla, et al15 showed there exists
strong relationships between an injection molder’s shear rate and the generation of AA,
as well as between the polymer’s processing time and the amount of AA that is generated.
Intuitively, to minimize the effects of thermal degradation and the amount of generated
AA, a balance must be made between the processing temperature, the residence time, and
discussed in Section 1.3.3, occurs when oxygen reacts with PET at elevated temperatures.
By comparing various melting environments, Jabarin and Lofgren14 showed that thermal-
oxidative degradation had higher reaction rates than thermal degradation; indicating that
degradation occurs more rapidly. Yoda, et al16 found that thermal-oxidative degradation
can lead to the formation of branched and cross-linked chains; and in some circumstances,
27
Both thermal degradation and thermal-oxidative degradation share many common traits.1
First, both mechanisms require excessive temperature to degrade the PET chains. Second,
for the most part, both degradation systems result in similar effects upon PET: reduction
Figure 1-12, located in Section 1.4.3.4, details the reaction scheme from which AA is
leaves the ethylene linkage of a PET chain susceptible to be attacked by oxygen. The
formed branched hydroperoxide group will decompose and form free radicals. The
formation of two free radicals causes the PET chain to split in two. One PET chain is
terminated by a vinyl ester end-group and the other is terminated by a hydroxyl end-
group. These functional end-groups then react with one another to re-form a PET chain
should be melted and/or processed under an inert environment. An example of this is the
continual flushing of the headspace of an extruder with nitrogen gas to displace any
28
2.2 Minimizing AA by Choice of Polymerization Catalysts
The manufacturing of PET requires the use of various metal acetates and/or oxides to
catalysts have been previously mentioned in Section 1.2.1.1. It is well documented that
catalyst systems play a critical role in the degradation of PET, and eventual generation of
AA. In separate publications, Zimmermann27, Rieckmann and Völker4, and Jabarin3 all
Zimmermann and co-workers27 have extensively studied both the thermal and thermal-
oxidative degradation of PET. This work was performed by using a variety of catalyst
systems. Zimmermann identifies cobalt (Co), cadmium (Cd), nickel (Ni), and zinc (Zn)
as the most aggressive catalysts which lead to PET degradation. Kao, et al28 verified
Zimmermann’s work, reporting that the use of Co, copper (Cu), and Zn acetates increase
the rate of degradation within PET. Derivatives of antimony (Sb), meanwhile, have been
phosphorus (P) based additives are able to provide stabilization and reduce the rate of
degradation.
29
2.3 Minimizing AA by Choice of PET Resins
As previously mentioned in Section 1.4.4, one avenue toward limiting the generation of
AA is through the use of specifically designed PET resins.2 These PET resins are
sometimes referred to as “water-grade” resins, since they have been “specifically tailored
to the needs of water containers”.2 Since water does not require carbonation, the strength
requirements of carbonated soft drink (CSD) PET containers. The PET water bottles
need only enough strength to house the packaged water and survive an impact.
Fundamentally, a reduction in the strength requirements for PET packaging means that
the material’s molecular weight or I.V. can be reduced. Generally, “water-grade” PET
bottles can be manufactured with resins that range in I.V. between 0.70 and 0.76 dL/g;
whereas, bottles manufactured for CSD packaging require an I.V. between 0.80 and 0.84
dL/g. Some20 believe that since these “water-grade” resins have lower intrinsic
viscosities, they are inherently exposed to less shear heating than are CSD grade resins,
during processing. Shukla, et al15 showed that minimizing shear heating can significantly
reduce the amount of AA that is generated in PET. Other researchers,1, 31 however, feel
that AA generation is unrelated to molecular weight or I.V. It is their belief that chemical
composition (catalysts, monomers, etc.) is the dominant factor in whether a PET resin
30
2.4 Minimizing AA by Means of Acetaldehyde (AA) Scavengers
Acetaldehyde (AA) scavengers are additives, which when melt-blended into PET resin
are designed to interact with any acetaldehyde that is present in the PET matrix.20, 24
There are at least three different mechanisms through which this interaction occurs. One
type of scavenger is designed to react with any generated AA and the second is designed
to lock AA into its structure. Both of these systems do not minimize the amount of AA
that is generated during the processing of PET; they simply limit its release by interacting
with generated AA and thus its effects upon the packaged contents. A third type of
scavenger is a catalyst system that converts AA into another compound which possesses
2.4.1.1 Polyamides
for PET. Several Eastman Chemical patents describe the use of polyester/polyamide
blends to improve the flavor retention for polyester packaging applications. U.S. Patent
aromatic polyamides and low molecular weight aliphatic polyamides that can be used as
AA scavengers. Of the two general classifications listed, Long, et al32 states that
aromatic polyamides are more preferable than aliphatic polyamides because the aromatic
31
polyamides tend to be more easily dispersed and produce less haze. The patent describes
blends having a polyamide composition between 0.05% and 2%, by weight; the
adipamide) should be between 3,000 to 6,000 g/mol and an inherent viscosity of 0.4 to
0.9 dL/g. Long claims that MXD6 should possess a number average molecular weight
between 4,000 to 7,000 g/mol and an inherent viscosity of 0.3 to 0.6 dL/g. The chemical
Polyamides, particularly MXD6, have been added to PET to help improve its barrier
the polymer blend typically results. Bandi, Mehta, and Schiraldi48 studied the mechanism
from which chromophores are generated when PET is melt-blended with polyamides. Of
particular interest were PET/MXD6 blends. Bandi, et al48 linked the color generation to
the formation of an imine group, which is the result of a reaction between the amine end-
group of MXD6 and the aldehyde group of AA. It is through this reaction, shown in
32
Figure 2-2, that MXD6 exhibits its use as an AA scavenger when melt-blended with PET.
It should be noted that the reaction shown in Figure 2-2 does generate a byproduct, water
(H2O).
O
H2N H2 C CH2 NH OOC (CH2)4 COOH
+ H3C CH
(MXD6) (AA)
Other polyamides, besides MXD6, have also been evaluated as AA scavengers for PET.
amine groups that allow the polymers to scavenge AA in a similar manner as MXD6.
U.S. Patent 7,022,390 teaches that optimal polymethacrylamide concentration can vary
33
2.4.1.2 Low Molecular Weight Amides
U.S. Patent 7,550,20349 lists several low molecular weight amides that can potentially be
functional groups, an amide group and an amine group, attached to a substituted benzene
ring. According to Rule, et al50, the reaction between anthranilamide and acetaldehyde
produces “water and a resulting organic compound comprising an unbridged five or six
member ring including the at least two heteroatoms”. The patent goes on to described
two more details: one, “the unbridged 5 or 6 member ring of the resulting organic
compound is bonded to the aromatic ring” and, two, “the two heteroatoms are both
nitrogen”.
NH2
NH2
34
According to Rule, et al50, it is the formation of this second ring structure that makes
art methods that depend on the formation of inherently colored imines, the formation of
was the generation of imine functional groups that Bandi48 suggested was the reason for
color generation in PET/polyamide blend systems. In addition, Rule, et al50 also claims
that “thermodynamics often favor ring formation more than imine formation; thus,
significantly lower amounts of the organic additive compound of this invention can
2.4.1.3 Polyamines
Patent literature shows that polyamines can be added to oxygen scavenging systems to
react with and stabilize the byproducts that result from those reactions. In U.S. Patent
5,942,297 Speer, et al51 identifies a list of polyamines that can react with the various
aldehydes and alcohols that are formed during oxygen scavenging reactions. This list
supported polymeric amines, and amine functionalized silicas. The scavenging reaction
between terminal amines and aldehydes follow a chemistry similar to that in the reaction
scheme shown in Figure 2-2. This condensation reaction generates an imine compound
35
Similar to the application depicted by Speer, et al51, Ching, et al52 claims a similar use for
which one of the layers is comprised of an oxygen scavenging material, a second layer is
fourth layer is a polymeric selective barrier. The intent of adding these byproduct
diffusing through the multi-layer structure and into the packaged contents. The list of
neutralizing materials listed in Patent 6,057,01352 includes low molecular weight amines,
containing polymers are: glycols containing amine groups such as polyethylene glycol
with two amines and polypropylene glycol with two amines, and dimethylaminoethanol
2.4.1.4 Polyimines
In U.S. Patent 5,362,784, Brodie, et al53 teaches that a specific class of polyimines can be
polyethylene imine (PEI). It is recommended that PEI has an average molecular weight
36
of at least 2500 g/mol, is not heavily branched, and has a low amount of tertiary amines.
The optimal blending of PEI and PET is claimed by the authors to be between 0.01 and
10:100, by weight. It is mentioned within Patent 5,362,78453 that the use of binding
agents can be used to “lock in” the polyalkylene imines into the polymer matrix.
It should be noted that Brodie, et al discuss the use of PAI and PEI as aldehyde
scavengers in two more U.S. Patents; 5,284,89254 and 5,413,82755. The application of
these two patents, however, concern blending the polyimines with polyolefin materials.
2.4.1.5 Polyols
Polyols are a class of alcohols that contain multiple hydroxyl groups. The AA
scavenging ability of these compounds has been claimed by several researchers in patent
intended to enhance the material’s melt-strength. The specific polyols mentioned in U.S.
Woodward teach that their optimal concentration is between 100 and 50,000 ppm.
While McNeely and Woodward56 did not claim the AA scavenging ability of polyols in
their patent, Al-Malaika’s patents57, 58 do state that ability. In WO Patent 006665957 and
U.S. Patent 6,936,20458, Al-Malaika describes the use of polyol/PET blend systems as a
way to reduce AA. These multiple hydroxylic compounds should ideally possess
37
between 3 to 8 hydroxyl groups and be present between 0.0001 and 2%, by weight. The
In WO Patent 010072, Eckert, et al59 also describes the use of polyols as AA scavengers
in PET systems. The authors of this patent claim that desired polyols have at least one
primary hydroxyl group and another primary, secondary, or tertiary hydroxyl in the 2
and/or 3 position. The identified list of polyols that fit the criteria includes xylitol,
mannitol, and sorbitol. To reduce AA, the concentration of these additives can range
between 50 and 5000 ppm; although polyol content can be as high as 25% by weight.
An example of the aldehyde scavenging ability of a polyol is shown in Figure 2-4. In this
reversible reaction scheme, two molecules of D-sorbitol react with one molecule of
similar reaction occurs when AA is the sought after compound. This also yields water as
the byproduct.
Odorisio and Andrews60 also identified a group of polyols that can be used as AA
scavengers in PET. This group consists of homo- and copolymers of polyhydric alcohol-
containing polymers which are derived from 2-propenoic acid ester monomers. Within
this group, the most preferable is poly(glyceryl methacrylate) homopolymer. U.S. Patent
38
Figure 2-4: Aldehyde scavenging reaction between D-sorbitol and valeraldehyde24
2.4.2.1 Cyclodextrins
glucopyranose units.24 Figure 2-5 shows the how the classification of cyclodextrin
changes with the number of glucopyranose repeat units; it also shows how the internal
and external diameters change with the number of repeat units.61 Figure 2-6 shows the
39
Figure 2-5: Various forms of cyclodextrin62
Wood, et al have several patents63-70 claiming that cyclodextrin can encapsulate AA, as
wells as other permeates, into its molecular structure. An example of this interaction
Cyclodextrin does not inhibit the generation of AA during the melt processing of PET.
As with other AA scavengers, it merely limits the diffusion of AA out of the polymer’s
40
matrix.62 According to Wood, et al, the optimal amount of cyclodextrin melt-blended
Several authors71-74 have shown that 1H NMR (proton nuclear magnetic resonance
NMR titration studies. NMR titration studies involve varying the concentration of the
inclusion species (guest) to the concentration of cyclodextrin (host). 1H NMR spectra are
recorded for several samples of varying host to guest ratios. A plot is then made of the
change in the chemical peak shift (y-axis), in ppm or ∆δ units, versus the host to guest
One such NMR titration study was performed by Hao, et al71 who studied the complex
study was performed at room temperature, using deuterium oxide (D2O) as the solvent.
Figure 2-8 shows the change in the chemical shift (∆δ) for a proton of the guest molecule
41
(GSH), labeled H5 proton, as the concentration of the host molecule (2-TeCD) is
increased.
NMR measures the overall chemical environment which a particular hydrogen or carbon
atom experiences; depending on the analysis method: proton (1H) NMR or carbon-13
(13C) NMR. It does this by averaging the chemical shift seen for each particular proton
or carbon-13 atom. When the guest molecules are dissolved in a solvent, the 1H NMR
yields a standard chemical shift for each of its protons. This particular chemical shift is
based on the chemical environment which those protons experience in that particular
solvent.
As host molecules are added, guest molecules move from the solvent to the internal
structure of the host molecules. While the guest molecules are inside the internal
structure of the host molecule, hydrogen bonding occurs between the protons of the guest
42
molecules and the protons which line the internal structure of the host molecules. The
environment of the guest molecule’s protons. The instrument responds with a different
chemical shift for the guest molecules’ protons than previously seen when they were in
solvent alone. As the concentration of the host molecules increases, the number of guest
molecules which occupy the internal structure of the host molecules also increases. Since
the NMR instrument averages the chemical shift for each particular proton, the change in
The change in the chemical shift, of the guest molecules’ protons, occurs until a
saturation point is reached. This saturation point is achieved when all of the guest
molecules are occupying the internal structure of host molecules; thus changes in the
chemical shift of the guest molecules protons can no longer occur. The saturation point is
indicated in Figure 2-8 as the position where the slope of the graph flattens and it equals
zero. Figure 2-8 shows that the saturation point for Hao’s experiment71 occurs when a
2.4.2.2 Zeolites
Zeolites75 are a class of microporous, crystalline solids that occur both naturally and
synthetically. They are generally composed of aluminum (Al), silicon (Si), and oxygen
(O). The polarity of their internal pore allows cations such as sodium (Na), calcium (Ca),
and potassium (K) and small molecules such as water to fill their internal cavities.
43
Massey and Callander76 noted that the propensity for zeolites to absorb water, into their
internal cavities, is so strong that if water is absent from the system zeolites will allow
any material into their cavities as long as it is small enough to fit through the pores and
enter the internal structure. This filter mechanism allows zeolites to act as “molecular
In U.S. Patent 4,391,971, Massey and Callander76 teach of a process for reducing AA
content by passing molten PET through a filter containing a molecular sieve. The
an extruder outlet and a receiving mold of forming die”. Massey and Callander76 also
state that their process will improve the brightness and color of the resulting PET resin.
While Massey and Callander76 pass molten PET through a zeolite based filter to reduce
AA content, Mills, et al77 teach that zeolites can also be melt-blended into the polymer’s
matrix to achieve the same result. The authors claim that the addition of small- or
clarity of the final PET article. Small-pore zeolites have an eight tetrahedral structure
with an internal diameter of 4.1 angstroms (Å); while medium-pore zeolites have a ten-
Application 942937877 teaches that the optimal addition amount of these zeolites is
44
2.4.3 AA Scavenging Catalysts
Researchers have shown that certain catalyst systems can also act as AA scavengers. As
previously discussed in Section 1.2.1.1, the catalysts used for PET polymerization
include: acetates of antimony (Sb), lithium (Li), calcium (Ca), magnesium (Mg), zinc
(Zn), and lead (Pb); as well as oxides of Sb, Pb, and germanium (Ge). AA scavenging
catalysts are not added to assist in the polymerization of PET; there sole intent is to
convert the molecular structure of AA into another product which has different migration
Go and Burzynski78 describe a method for manufacturing PET resins with enhanced
thermal stability against the generation of AA. Their process incorporates an alkali metal
Patent 4,357,46178 teaches that the alkali metal should be either sodium (Na) or
potassium (K). The authors claim that the amount of EDTA can range between 0.001
and 0.2 mol percent. They indicate that amounts above 0.5 percent can lead to
discoloration.
In U.S. Patent 6,569,47979 and W.O. Patent 013090080, Rule teaches that an oxidation
catalyst can be used to convert AA to acetic acid. Rule claims that the conversion of AA
to acetic acid occurs as oxygen gas permeates the PET packaging. Therefore, this
reaction is also capable of decreasing the migration of oxygen through PET containers.
Converting AA to acetic acid is appealing because acetic acid has a taste threshold that is
45
more than 1000 times greater than acetaldehyde. The oxidation catalysts described in
these patents are simple cobalt (Co) or manganese (Mn) salts; or Co or Mn salts
comprised of an amine, phosphine, or alcohol complex. Rule79, 80 notes that simple salts
can include: cobalt acetate, cobalt octoate, cobalt naphilhenate, manganese acetate,
EDTA and glycine. The concentration of these catalysts should be between 1 and 500
Rule and Shi81 describe a PET resin comprised of a hydrogenation catalyst and at least
one source of reactive hydrogen. In this application, the hydrogenation catalyst can be a
Group VIII metal (zero valent nickel, palladium, or platinum) or a metal hydride (tin or
titanium based complex). According to U.S. Patent 7,041,350, the catalyst’s amount can
range between 0.1 and 100 ppm; optimally between 5 and 50 ppm. The identified
46
Chapter 3
Experimental Work
3.1 Materials
donated by Mitsubishi Gas Chemical America, Inc, and alpha-cyclodextrin was supplied
by the Wacker Chemical Corporation. Acetaldehyde was also purchased from Sigma-
Aldrich and used to spectroscopically study the chemical interactions that occur between
AA and the various scavenging materials. The spectroscopic analysis, particularly NMR,
was conducted in the presence of deuterated solvents. Deuterium oxide (D2O) and
Laboratories.
Chemical, is a PET copolymer resin with an initial I.V. of 0.84 dL/g. It is designed to be
47
3.2 Spectroscopic Techniques to Study Chemical Interactions
AA scavengers work by interacting with the acetaldehyde that is present within PET.
These chemical interactions prevent AA from diffusing from the matrix of the polymer
and into either the packaged contents of the container or into the atmosphere. Studying
and determining these chemicals interactions was achieved through two spectroscopic
NMR provided the primary information, while mass spectroscopy was used to
perform structure elucidation and determine the identity of unknown compounds.82 NMR
works on the premises that certain nuclei (1H, 13C, etc.) have magnetic properties when in
absorbed by the nuclei and then sent back out. The energy is remitted at a specific
The most commonly studied nuclei in NMR are 1H and 13C. The appeal of studying these
two nuclei is due to their relative abundance within organic compounds. Although 1H
NMR is about 5700 times more sensitive than 13C NMR83, both techniques are very
powerful and capable of providing significant data. These NMR methods are sometimes
48
referred to as “one-dimensional” techniques. The reason for this designation is because
the resulting spectrum from 1H or 13C NMR appears relative to only one axis or scale.
NMR techniques. “Two-dimensional” NMR yields spectra that are shown relative to two
scales; one scale is on the x-axis and the other scale is on the y-axis. The data can be
correlated between these two axes to show which nuclei are coupled or connected to one-
methods provide, making it possible to decipher the chemical structure of compounds too
scavengers and acetaldehyde, proton nuclear magnetic resonance (1H NMR) was used.
1
H NMR was chosen over 13C NMR for two reasons: one, 1H NMR is approximately
5700 times more sensitive than 13C NMR and two, 1H NMR is able to provide
quantitative data; something 13C NMR cannot always provide.82 For this project, the
NMR Varian Inova 600 MHz spectrometer, located in the University of Toledo’s
49
The 1H NMR work began by analyzing the various AA scavengers and acetaldehyde
deuterated solvent. Its spectrum was then obtained and analyzed to characterize each 1H
After obtaining the spectrum for each respective component, the next step was to mix
acetaldehyde with each scavenger and study any changes in the resulting 1H NMR
spectrum. Both acetaldehyde and an AA scavenger were separately dissolved using the
same deuterated solvent. The weights of each component were recorded so that the
proper stoichiometric ratio was achieved. These solutions were then mixed together in an
1
3.2.1.2 H-1H COrrelation SpectroscopY (COSY)
of the protons that compose the studied chemical compound83; helping to map-out the
chemical structure. The output of this experiment is the sample’s 1H NMR spectrum on
both the y- and x-axes. Since these spectra are obtained by the same magnetization, there
is a symmetry that yields “diagonal peaks”. The “off diagonal peaks” or “cross peaks”
50
1
H-1H COSY NMR was used to help decipher those 1H NMR spectra that were, alone,
too hard to interpret. The sample preparation for this experiment was the same as for 1H
NMR. Separately, acetaldehyde and an AA scavenger were dissolved using the same
deuterated solvent. These two solutions were stoichiometrically mixed together and then
analyzed. Analysis was conducted via the NMR Varian Inova 600 MHz spectrometer,
Mass spectrometry is a versatile, analytical tool that can be used to both qualitatively and
quantitatively determine an unknown analyte based upon its mass.82, 83 Upon entering a
incumbent within the machine. These generated ions are then separated, by the
instrument’s separations method, based upon their mass to charge ratio.82 The
spectrometer’s detector subsequently quantifies the amount of ions at each mass to charge
ratio, yielding a chart illustrating the abundance of each ion at the various ratios.83
There are various types of mass spectrometers, each possessing a different ionization
method and a different mass analyzer.82, 83 For this project, the Esquire liquid
ionization, as its ionization source, and an ion trap, as its mass analyzer. The intent of the
51
mass spectrometry experiments was to compliment and validate the results seen from the
NMR work.
The preparation of each sample was as follows. A small amount of the sample, typically
with the ionization process, a very small aliquot of methanol was added to the dissolved
sample. Prior to analysis, the mass spectrometer was purged with pure solvent, in order
to clean the instrument of any residual impurities. Experimental samples were then
directly injected into the mass spectrometer. The resulting spectrum was recorded and
analyzed.
Werner and Pfleiderer ZSK-30 twin-screw extruder; operating at 300 revolutions per
minute (rpms) and 280oC. Attached to this extruder are a nitrogen tank and a vacuum
pump. Nitrogen gas is fed into the throat of the extruder to displace any oxygen, creating
an inert environment for PET melting and processing. The vacuum pump is attached to
the barrel of the extruder and is used to remove any volatile chemicals that are generated
agents with the CSD PET resin. For each AA scavenger, a “master-batch” AA
52
scavenger/PET blend sample was initially extruded. Further concentrations of each AA
scavenger/PET blend system were made by diluting the appropriate “master-batch” blend.
amount of virgin PET. For comparative purposes, control samples were also extruded
under similar conditions. These samples were the same CSD PET resin, however,
Prior to extrusion, all PET samples were dried overnight at 150oC and under vacuum; in
either a Conair Franklin desiccant hopper/dryer or a small vacuum oven. This step was
taken to limit the presence of moisture and thus minimize the effect of hydrolytic
resin and the AA scavenger were weighed and then placed in separate vacuum ovens.
The virgin PET sample was dried overnight at 150oC, while alpha-cyclodextrin was dried
at 80oC. After drying, the alpha-cyclodextrin and PET samples were removed from their
respective ovens and dry-mixed in a small metal bucket. The mixing was done as quickly
as possible to minimize the resin’s absorption of moisture from the atmosphere. This
PET blend was then extruded, pelletized, and collected. The concentration of alpha-
53
Through the dilution of this 5 weight % alpha-cyclodextrin/PET master-batch sample,
further blend concentrations were obtained. A 2.5 weight % blend was produced by
melt-blending equal parts, by weight, of the 5 weight % master-batch sample with the
virgin, CSD PET resin. Each of these components was weighed and placed in a metal
bucket that was dried overnight in a small vacuum oven, at 150oC. The next morning this
sample was extruded, pelletized, and collected. A similar process was followed to yield 1
weight % (or 10,000 ppm) and 0.5 weight % (or 5000 ppm) alpha-cyclodextrin/PET
blend samples.
was used as the concentrate instead of the 5 weight % master-batch sample. The thought
was that by using a more diluted blend the AA scavenger would have a better chance of
being uniformly dispersed, within the PET resin, during the extrusion process. A better
This methodology may have increased the possibility of acquiring more uniform AA
thermal histories of these PET blends. As an example, portions of the 500 ppm alpha-
• Extruded once: the virgin PET resin added to dilute the 1 weight % blend to the
54
• Extruded twice: the virgin resin melt-blended with the 5 weight % master-batch
• Extruded three times: the 5 weight % master-batch sample that was extruded with
blend
Table 3.1 breaks down the thermal histories of the various alpha-cyclodextrin/PET blend
samples. This table shows how much of each sample was extruded once, twice, and even
The preparation of the anthranilamide/PET blend samples was very similar to the
of the AA scavenger and pure resin. Each sample was place in its own vacuum oven and
dried overnight; virgin PET at 150oC and anthranilamide at 80oC. The next morning,
these two components were dry-mixed in a small metal bucket and then extruded and
55
pelletized. The anthranilamide concentration of this master-batch sample was 1
weight %.
sample was further diluted to make additional blend samples. The 1 weight % (or 10,000
1200 ppm blend and a 500 ppm blend. The lowest anthranilamide/PET blend samples,
the 200 ppm and the 100 ppm blends, were prepared from the 1200 ppm concentrate. As
discussed in Section 3.3.1, a more diluted blend was used with the hope that it would
produce less variability and more homogeneity among these samples. Table 3.2 has been
prepared to show the amount of each anthranilamide/PET blend that has been extruded
The process to produce the MXDA/PET blends varied slightly in comparison to the
56
temperature MXDA is a liquid84; while alpha-cyclodextrin85 and anthranilamide86 are
crystalline materials. To blend this scavenger with PET, MXDA was pumped into the
throat of the extruder at a desired rate; through the use of a pump. Prior to extrusion, the
virgin PET resin was dried overnight at 150oC in a Conair Franklin hopper/dryer to
eliminate moisture.
The next morning, the process began by extruding PET resin until a steady-state was
established. Once steady-state was achieved, the pump was turned on, blending MXDA
with the molten polymer. Collection of the pelletized MXDA/PET blend sample began
three minutes after the pump was initially turned on. As with the previous processes, a
vacuum pump and nitrogen gas were used to limit the degradation of the material during
extrusion. Since MXDA is known to be very reactive, a plastic tarp was used to create a
tent that surrounded the twin-screw extruder. This precaution was used to direct any
volatiles toward the lab hood that was located above the extruder. The resulting
should be noted that this sample had a slight greenish tint to its appearance.
The various MXDA/PET blend samples were produced by the same manner as described
(Section 3.3.2) for the range of anthranilamide/PET blends. The 1 weight % (or 10,000
ppm) master-batch blend was used to make a 1200 ppm blend and a 500 ppm blend. The
200 ppm and 100 ppm blend were created from the 1200 ppm MXDA/PET concentrate.
Table 3.3 shows the amount of each MXDA/PET blend that has been extruded once,
twice, and even three times. Since the MXDA/PET blend samples were prepared in the
57
same manner as the anthranilamide/PET blend samples, the thermal histories shown in
A pure PET resin, without the addition of any AA scavenging agent, was extruded under
various AA scavenger/PET blends. The resin used to establish this control sample was
the same CSD PET resin which was melt-blended to make each of the various AA
Sections 3.3.1, 3.3.2, and 3.3.3, a total of three control samples were prepared. Prior to
processing, all of these samples were dried overnight at 150oC in a Conair Franklin
The process to prepare these three control samples began by initially extruding,
pelletizing, and collecting a large amount of the CSD PET resin. About one-half of this
“one-time processed” control sample was set aside for analysis. The other half of this
sample was re-extruded to establish the “two-times processed” control sample. Again,
58
about one-half of this “two-times processed” sample was set aside for analysis and the
other half was re-extruded to create the “three-times processed” control sample.
While this approach does not replicate the exact blend ratios established in Sections 3.3.1,
3.3.2, and 3.3.3; it does allow for comparisons to be made. For any analytical method,
the evaluation of each control sample produces data which can be proportioned with the
data from the other two control samples. This method creates theoretical values that can
these two samples match. Matching the thermal histories is achieved by proportioning
the correct amount of the “one-time processed”, “two-times processed”, and “three-times
processed” control samples to equal the ratio for any particular AA scavenger/PET blend
Producing PET containers is generally performed by means of a two stage process. The
first step is known as injection molding, a process that melts PET resin and pushes the
viscous polymer to fill a mold. For container manufacturing, the article that is produced
This second and final step of the container manufacturing progression heats the PET
preforms to temperatures that are slightly above the glass transition temperature (Tg) of
59
the material, but below its crystallization temperature. When a polymer is heated above
its Tg, it transitions from a glassy state into a rubbery state. These rubbery preforms are
then mechanically stretched, by a rod, and blown to fill another mold. The result of the
The Arburg 320S machine was used to injection mold preforms. This is a single cavity
injection molder that has a 55-ton capacity and a reciprocating screw. The processing
injection pressure was set at 1500 bar and the cooling time was 10 seconds. The mold
used this work produces preforms specifically designed for 2-liter bottle manufacturing.
scavenger/PET blend was dry-blended with a determined amount of virgin PET. Each
dry-blended sample was then dried overnight, at 150oC, in a Conair Franklin hopper/drier.
After drying, a transfer pipe from the Conair Franklin drier was attached to the throat of
the injection molder for automated resin loading. A pure PET resin sample was also
60
For each sample set, the first ten preforms were discarded; allowing the machine to reach
a steady-state until sample collecting began. Once the machine reached steady-state,
twenty samples were collected and immediately placed in a freezer. This was to prevent
any acetaldehyde from diffusing from the PET preforms and into the atmosphere; a vital
step toward assuring accurate results when analyzing the residual AA content of those
samples. The remaining preforms were set aside to be stretch-blow-molded into 2-liter
bottles.
3.4.2 Stretch-Blow-Molding
Transforming the prepared preforms into 2-liter bottles was achieved through a stretch-
blow-molding process. This process begins by heating a PET preform above its Tg, as a
result of exposure to infrared radiation (IR). The IR heating system consists of twelve
quartz lamps, each rated at 1600 watts; with peak filament temperatures of 2200K at 240
volts. These twelve zones can be adjusted to alter the temperature profile. Figure 3-1
shows a drawing of a preform and approximately where the twelve zones are located.
1 2 3 4 5 6 7 8 9 10 11 12
Figure 3-1: Relative location of IR heating zones with respect to a perform
61
After loading a preform onto a rotating mandrel, the IR heater box passes the PET
preform twice; returning to its starting position. The speed at which the heater box passes
the preform and the voltages of the twelve IR heaters were optimized yield the best
possible bottles. Additionally, the stretch rod pressure and the blow pressures were
optimized to yield the best bottle appearance. Table 3.4 shows the optimized stretch-
and used to quantify analytes. Chromatography methods are defined by their respective
stationary and mobile phases.82 Gas chromatography (GC), for example, uses a carrier
gas as the mobile phase and a solid column as the stationary phase.
62
During GC, an inert carrier gas moves the gaseous sample through a long column, which
is stored within an oven, and eventually to the instrument’s detector where it will be
quantified. As the sample moves through the column, it separates into its individual
chemical species based on the affinity that each individual chemical species has toward
interactions is strong between the chemical compound and the stationary phase, then it
will have a longer retention time within the column than a chemical that does not interact
by two different techniques. The first method determines the rate at which AA is
generated during the processing of PET resin. The second technique, known as
headspace analysis, is used to determine the amount of AA that remains trapped within
rates were studied by a method described by Kim and Jabarin23. This technique simulates
the heating conditions that are needed to process PET. Measurements are made through
the use of a Perkin-Elmer Automatic Thermal Desorption System (ATD 400) coupled to
63
0.32 mm. The column temperature was 60oC and used a helium gas purge. The GC uses
a flame ionization detector (FID) to sense the amount of analtyes that have passed
through the system. Perkin-Elmer’s TurboChrom software then interprets the FID’s
Samples for this measurement are PET pellets, virgin or with AA scavengers, which have
been dried and crystallized overnight, at 120oC, in a vacuum oven. For each sample, two
PET pellets are weighed using a five decimal place analytical balance; the combined
target weight for these pellets is 0.03 ± 0.01 grams. These two pellets are placed in a
cylindrical Teflon sample chamber, separated by quartz wool. This packed sample
chamber is placed into a metal sample tube. Each sample tube that is placed in the ATD
400 is melted for a specified residence time and at a specified temperature; establishing
only one data point along the AA generation curve. Multiple samples, measured at
varying residence times, are therefore required to create an AA generation curve. The
slope of this curve is the AA generation rate for the studied PET sample, at the evaluated
temperature.
concentrated standard into a metal sample tube, containing a Teflon sample chamber
packed with Tenax®; an analyte absorbing agent. This standard is purged into this
sample tube for five minutes at a pressure of 0.5 pounds per square inch (psi). This
process was repeated at least three times in order to obtain an averaged peak area. These
prepared standards are placed in the ATD 400 and heated for 10 minutes at 250oC. The
64
instrument’s response is determined by dividing the averaged peak area, for the AA
standards, by the amount of sample injected. A typical value for the GC’s instrument
Equation 1 shows the equation used to calculate the amount of AA for each sample.
E PA 1
AA = × (Equation 1)
E SW S IR
AA generation rates were established at three different temperatures (280, 290, and
300oC) so that the activation energy (EA) could be determined by means of the Arrhenius
equation. Equation 1 shows the Arrhenius equation in its most common form. Table 3.6
shows the Arrhenius equation in a derived form. Using this equation, the activation
energy can be determined graphically by plotting the natural log of the rate versus the
inverse of the temperature, in degrees Kelvin. The slope of this plot is the activation
65
energy divided by the gas constant, and the y-intercept is the natural log of the pre-
exponential factor.
EA
k = A× e RT
(Equation 2)
E 1
ln (k ) = ln( A) − A × (Equation 3)
R T
As AA is generated through the degradation of PET it has the ability to diffuse out of the
polymer’s matrix; due to AA’s low boiling point of 21oC.19 A portion of the generated
AA, however, usually remains trapped within the manufactured PET article as residual
for many packaging applications because many foods and beverages have a limited
66
For this work, the quantification of residual AA was performed by a headspace analysis
for headspace analysis are identical to the parameters that were previously mentioned in
Section 3.5.1.
For this measurement, processed samples (either melt-blended by twin screw extrusion or
injection molded into preforms) were immediately collected and placed in a freezer to
prevent the AA from volatilizing out of the PET matrix. Each sample, in its amorphous
state, was ground by means of a small grinder made by the Tekmar Company. The
amorphous PET sample was placed in the grinder and then saturated with liquid nitrogen
to keep the polymer cold. The resulting ground powder was then separated using a sieve
combination of 20 mesh, 40 mesh, and solid bottom. Only the 20 mesh sample was
collected and used for this analysis. This is done in order to maximize surface area and
increase amount of AA that can diffuse from PET. The ground PET samples were, again,
immediately placed back into the freezer to prevent the diffusion of AA.
Prior to analysis, the PET powder samples were removed from the freezer and then
weighed on a five decimal place analytical balance. The samples are weighed within a
glass sample vial which is capped and sealed immediately after weighing. During
analysis, each sample is heated for 60 minutes at 150oC and at 18 psi. This temperature
does not melt the PET, it simply volatizes the residual amount of AA that is trapped
within the PET into the headspace of the glass vial. Once the sixty minutes has lapsed,
67
the TM 40 injects a needle and extracts a sample of the gaseous headspace. This sample
Calibration for this technique is similar to the procedure that is followed to perform
are respectively injected, by means of a syringe, into a glass sample vial. The
standardized sample has a typical concentration of around 1.002 µg/µL. Each of these
five samples is heated for 15 minutes at 150oC and at 18 psi. The instrument’s response
factor is determined by plotting the resulting peak areas against the respective AA
concentrations; the origin is also used as a data point. The instrument’s response factor is
the slope of this linear line. Typical instrument response values for headspace
previously shown in Section 3.5.1. Equation 1 uses the experimental sample’s weight
(ESW), the experimental sample’s resulting peak area (EPA), and the instrument’s response
factor (SIR) from the calibration standards to tabulate the AA content within the PET
sample. Table 3.5, also located within Section 3.5.1, provides further explanation of the
variables in Equation 1.
68
3.6 Rheological Methods
its melt viscosity. Conversion from melt viscosity to intrinsic viscosity was made by
evaluating the melt viscosities of standardized samples that possess precisely known I.V.s.
The solvent used to measure the intrinsic viscosities of standard PET samples was
Melt viscosity measurements were made by a RDA III viscoelastic tester from
Rheometric Scientific. Measurements were made at using parallel plate and plate
geometry. Before making any measurements, the PET samples were crystallized and
dried, at 140oC, overnight. Table 3.7 summarizes the test conditions for the melt
viscosity measurements.
69
3.6.2 Capillary Rheometer
An Instron Capillary Rheometer was used to study the viscosity of PET resin as a
function of varying shear rates. Pelletized, virgin PET resin was dried overnight, at
140oC, prior to analysis. Measurements were made at three different temperatures (260,
270, and 280oC) so that the data could be extrapolated to predict the material behavior for
an even wider range of temperatures. The resin samples were melted under an inert,
nitrogen environment. Once the samples were completely melted within the capillary
column, a desired crosshead speed was set and the force was measured; this was varied
over a range of crosshead speeds. Using this data, along with instrumentation parameters,
the apparent shear rates, shear stresses, and apparent viscosities were tabulated. Plots of
viscosity versus shear rate yielded the desired rheology curves. Mathematical constants
were determined from these plots and were used to predict the resin’s rheology behavior
within the multi-cavity injection molding modeling program. Table 3.8 lists the
Changes in color, due to the processing and/or addition of additives melt-blended into
PET, were analyzed by means of a Hunter Lab Color/Difference Meter D25-2. The
70
instrument was initially calibrated using the standard colored plates supplied the
temperature. Response from the instrument yields L, a, and b values for each sample.
These values were then converted to Y, X%, and Z% values; according to Equations 5, 6,
and 7, respectively. Ultimately, the Y, X%, and Z% values were used to calculate a
yellowness index (YI). The yellowness index was calculated according to ASTM D
YI =
(125 × ( X % − Z % )) (Equation 4)
Y
a× L
(
X % = 0.01 × L2 + ) (Equation 6)
175
b× L
Z % = (0.01 × L2 ) − (Equation 7)
70
Table 3.9 gives an explanation of the L, a, b, and YI values that are obtained from the
71
3.8 Differential Scanning Calorimetry (DSC) Analysis
thermal properties of polymeric materials. DSC analysis was performed to see if any
changes in the thermal properties of the PET resin resulted from the melt blending of AA
scavenging agents into PET. Measurements were made by means of a Perkin-Elmer DSC
during melting of the samples. Prior to analysis, samples were vacuum dried overnight at
120oC. Each sample was heated to 300oC, held for 5 minutes to remove all of its inherent
crystallinity, and then rapidly quenched to 40oC creating a completely amorphous sample.
The sample was then reheated at 10oC per minute to give the melting behavior, the
crystallization behavior, as well as a value for the glass transition temperature (Tg).
Cooling the sample at a rate of 10oC per minute also indicated its crystallization behavior
Understanding the oxygen permeation rate for a given polymeric material is vital
atmosphere permeates through the plastic wall of the package, interacting with the
packaged contents. Depending on the sensitivity of the contents, this interaction can alter
the shelf-life of the packaged material. Studying the oxygen film permeation was
72
conducted to determine if the addition of AA scavengers would have any affect upon the
In order to understand the oxygen permeation rate a coulometric method was used,
similar to the one described in ASTM Procedure D 3985.88 This procedure involves the
use of the MoCon OxTran 1050 Oxygen Permeation Analyzer. This instrument uses a
single coulometric detector that is switched by a valve to any of the 10 samples cells
Samples from sidewalls of stretch blow molded bottles were cut into four inch squares;
two samples of each material were analyzed. For each sample, the average thickness was
calculated after measuring the sample’s thickness at nine evenly distributed points using a
Magna-Mike® 8500. With the sensor turned off, the samples were placed in the
respective chambers of the analyzer and sealed in place. Initially, baseline measurements
were made by purging the instrument of any oxygen with nitrogen gas. Once a baseline
for each chamber was established, the purging gas was changed to oxygen. Over time the
oxygen permeates from one side of the chamber, through the polymeric samples, and to
the other side of the chamber where the oxygen purge is detected. The instrument output
is an electrical current that corresponds to the amount of oxygen present. This current
Equation 8 shows the calculation used to determine the oxygen gas transmission rate
73
GTR = ( AV − BV ) × IF (Equation 8)
It should be noted that the baseline voltage is an averaged value, based upon two
measurements. The voltage for oxygen permeation is the actual daily value; therefore,
the oxygen gas transmission rate is calculated each day and not an averaged value. This
GTR
OP = (Equation 9)
∆P
74
Since the fluctuations in barometric pressure are accounted for, the oxygen permeance
may be averaged over the time of analysis. This averaged value for oxygen permeance
can now be used, along with the average thickness of the sample, to determine the
oxygen permeability, shown below in Equation 10. Table 3.12 gives an explanation of
P = OP × AT (Equation 10)
75
Chapter 4
sequester AA and the exact stoichiometry for each of these mechanisms. For each
experiment, the AA scavenging mechanism was studied under the most ideal
circumstances. Most notably, the presence of PET was omitted from each system;
solvent and mixed only with the other, respective reactant and solvent solution.
components. Figure 4-1 shows the 1H NMR spectrum of AA, dissolved in deuterated
76
chloroform (CDCl3). Under each prominent signal there is an integration factor,
indicating the number of protons which are represented by that particular peak. From left
to right, the 1 to 3 ratio shown in Figure 4-1 correlates the one hydrogen atom in AA’s
aldehyde (O=CH) group to the three hydrogen atoms located in its methyl (CH3) group.
The scale on the x-axis is in ppm or δ units. Table 4.1 provides a list of the assigned
2.07
9.66
9.65
9.65
0.93 3.00
10 9 8 7 6 5 4 3 2 1
Figure 4-1: 1H NMR spectrum of AA in CDCl3
77
The 1H NMR spectrum of anthranilamide, also dissolved in deuterated chloroform, is
shown in Figure 4-2. A prominent feature of this spectrum is the broad singlet that
appears at 5.67 ppm. The peak’s broadness is due to the fact that it represents
Generally, these protons are present on heteroatoms such as oxygen (O), sulfur (S), and
nitrogen (N). The peak at 5.67 ppm represents the four protons which comprise both the
amide (O=CNH2) and the amine (NH2) groups of anthranilamide. Also shown in Figure
4-2, a number is adjacent to each of anthranilamide’s four methine (CH) groups; all are
located within the ring formation. This numbering system corresponds to Table 4.2 and
is used to ease the identification of these CH groups which are represented by the peaks
78
Table 4.2: Peak assignment for the 1H NMR spectrum of anthranilamide in CDCl3
Peak Peak Integration Peak Assignment
Location Type Factor Chemical Functional Ring
(ppm) Compound Group Position
5.67 Singlet 4.5 Anthranilamide NH2 and -
O=CNH2
6.63 Triplet 1 Anthranilamide CH 3
6.665 Doublet 1 Anthranilamide CH 4
7.20 Triplet 1 Anthranilamide CH 2
7.24 Singlet - Chloroform-d -
7.34 Doublet 1 Anthranilamide CH 1
tubes. These two solutions were combined into one tube, at room temperature, and then
reaction between anthranilamide and AA took place. This spectrum was simply a
combination of the 1H NMR spectra of AA (Figure 4-1) and anthranilamide (Figure 4-2).
The conclusion from this experiment was that energy must be added to this system to
initiate a reaction.
These two solutions, in separate NMR tubes, were then combined into one NMR tube
that was subsequently was sealed. To seal this glass NMR tube, the contents (AA,
anthranilamide, and deuterated chloroform solution) and the bottom of the tube were
frozen in liquid nitrogen. Throughout this process, vacuum pressure was applied to
continually remove air from the system. The neck of the NMR tube was then heated with
a gas flame to melt the glass. When the glass reached a sufficient temperature, the tube
79
was twisted and a seal was created. The creation of this seal ensured that this solution
could be heated without the risk of volatilizing and losing any of the components.
Figure 4-3 shows the 1H NMR spectrum that resulted after heating the anthranilamide
and AA solution, in the sealed tube, for two days at 60oC. This sample was kept just
under the boiling point deuterated chloroform, which is 62oC. Interpretation of Figure
4-3 indicates that two compounds still remain in this solution, and one of these
2.21 ppm and the quartet at 9.80 ppm. These peaks closely mirror the location of AA’s
peaks in Figure 4-1; the integration factors are close matches as well. There are two
pieces of evidence within Figure 4-3 that indication the second component is a product
The first bit of evidence is the appearance of a new peak (doublet) at 1.50 ppm, and has
an integration factor of three. The location and integration factor indicate this peak
represents a methyl group (CH3). The fact that this peak is a doublet means that it is
the formation of a quartet peak at 5.06 ppm. This peak’s integration factor equals one,
coupled to three other protons. Previously stated, the methyl group at 1.50 ppm was
80
coupled to an unknown peak representing one proton. The combination of these two
Figure 4-3: 1H NMR spectrum of the reaction between anthranilamide and AA, in
CDCl3, after heating for 2 days at 60oC
A peak assignment list for the 1H NMR spectrum shown in Figure 4-3 is provided in
Table 4.3. Within this list, there is a broad singlet at 6.24 ppm that has yet to be
determined. The broadness of the peak and integration factor indicates that it correlates
in solution, however, these protons exchange so rapidly that it is not always possible to
correlate the integration factor with the number of protons for which peak truly represents.
81
Table 4.3: Peak assignment for the 1H NMR spectrum of the reaction between
anthranilamide and AA, in CDCl3, after heating for 2 days at 60oC
Peak Peak Integration Peak Assignment
Location Type Factor Chemical Functional
(ppm) Compound Group
1.50 Doublet 3 Reaction Product CH3
2.21 Doublet 15.5 AA CH3
5.06 Quartet 1 Reaction Product Undetermined
6.24 Singlet 1 Reaction Product Undetermined
6.68 Doublet 1 Reaction Product CH
6.87 Triplet 1 Reaction Product CH
7.27 Singlet - Chloroform-d
7.31 Triplet 1 Reaction Product CH
7.89 Doublet 1 Reaction Product CH
9.80 Quartet 4 AA O=CH
To provide further clarity and proof of a reaction between anthranilamide and AA, a 1H-
1
H COSY (COrrelation SpectroscopY) NMR experiment was conducted. The scale of
the peak intensities, as seen in Figure 4-4, is very difficult to read because of the
dominant size of AA’s methyl group peak at 2.21 ppm. Figure 4-4 validates the earlier
hypothesis that the quartet peak at 5.06 ppm is coupled with the doublet at 1.50 ppm.
This spectrum, however, shows no other evidence of this peak at 5.06 ppm being coupled
to any other protons. This means one of two things: either this group is not bonded to
82
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
6.5
7.0
7.5
8.0
8.5
9.0
9.5
9 8 7 6 5 4 3 2
Figure 4-4: 1H –1H COSY NMR spectrum of the reaction between anthranilamide and
AA, in CDCl3, after heating for 2 days at 60oC
Analysis of the previous two NMR spectra can lead to the prediction of at least two
different mechanisms which are able to describe the reaction that occurs between
anthranilamide and AA. The first proposed reaction mechanism is shown in Figure 4-5.
83
This compound has a terminal methyl group (CH3) and a CH group which is attached to
O
O O OH
+ NH2
NH2
H3C H NH CH3
NH2
(Anthranilamide) (AA)
As a way to help confirm reaction mechanism #1, shown in Figure 4-5, the ChemSketch
software package was used to predict the 1H NMR spectrum for the reaction product.
The predicted 1H NMR spectrum, shown in Figure 4-6, shows a similar pattern to the
actual spectrum, shown in Figure 4-3; with one exception. In Figure 4-3 the quartet
appears at 5.06 ppm, while in Figure 4-6 that peaks appears at about 5.53 ppm. Further
analysis was needed to prove if this 0.5 ppm difference is significant or if this value lies
84
15
14
7.32[13]
13
12
O
11 CH3
11
3 10 12
1.30[12]
10
4 2 NH2 1.32[12]
13
5 1 8
9
6 NH OH
7 9
8
7
Molecular Weight = 180.2 g/mol
6
5.51[8]
3
5.53[8]
7.24[5]
2 8.05[3] 7.22[5] 5.54[8]
8.07[3] 7.12[4] 5.49[8]
0.20[7,9]
1
0
10 9 8 7 6 5 4 3 2 1 0
Figure 4-6: Predicted 1H NMR spectrum for the product formed from the proposed
reaction mechanism #1 (Figure 4.5)
4-7. This reaction results in the formation of water and a two ring structured, organic
compound. Similar to the reaction product formed in proposed reaction mechanism #1,
shown in Figure 4-5, this compound has a terminal methyl group (CH3) and a CH group
which is attached to two heteroatoms. This time, however, the CH group bonds to two
85
O
O O
NH
+
NH2
H2O + H
H3C H N
H CH3
NH2
(Anthranilamide) (AA)
ChemSketch was again used to help evaluate the reaction products from another proposed
reaction mechanism between anthranilamide and AA. Previously it was shown that the
only significant difference between the predicted 1H NMR spectrum from the first
proposed reaction mechanism (Figure 4-6) and the actual spectrum (Figure 4-3) was the
location of the CH quartet peak; 5.53 and 5.06 ppm respectively. This time, however, the
predicted 1H NMR spectrum, shown in Figure 4-8, of the reaction product shown in
Figure 4-7 closely matches the actual spectrum shown in Figure 4-3. The location of the
predicted quartet peak, representing the CH group, is 4.98 ppm; very close to the actual
86
10
1.49[11]
1.47[11]
9
8 O
12
10
9 5
6 NH
7
1
8 4 2
N CH3
6 7 11
H
3
5
Molecular Weight = 162.2 g/mol
4
4.08[1]
7.16[8]
2 7.14[8]
7.64[10] 7.06[9] 4.98[2]
7.66[10] 6.40[7]
1
4.96[2]
0
10 9 8 7 6 5 4 3 2 1 0
Figure 4-8: Predicted 1H NMR spectrum for the product formed from the proposed
reaction mechanism #2 (Figure 4-7)
Based on the data presented up to this point, it is difficult to truly distinguish between
these two proposed reaction mechanisms. Even though the 1H NMR spectra for proposed
reaction mechanism #1 (Figure 4-6) and proposed reaction mechanism #2 (Figure 4-8)
are very similar, there is one drastic difference. The reaction product for proposed
reaction mechanism #1 has a molecular weight of 180.2 grams/mol; while, the reaction
product for proposed reaction mechanism #2 has a molecular weight of 162.2 grams/mol.
One way to distinguish between the two mechanisms would be through the use of mass
spectrometry.
87
Electrospray ionization (ESI) mass spectrometry was used to analyze both a sample of
samples to aid with the ionization process. The mass spectrum of the anthranilamide
solution is shown in Figure 4-9. Within this figure, it can be seen that the molecular ion
peak is located at 159.1 m/z (mass to charge ratio). The molecular weight of
two masses is 23 grams/mol, the molecular weight of sodium (Na). Sodium is a major
component of glass containers, which happens to be what the sample was stored in prior
to analysis.
159.1
120.1
213.1
0
100 120 140 160 180 200 220 m/z
88
Figure 4-10 shows the mass spectrum of the product from the reaction between
anthranilamide and AA. The molecular ion peak for this product is 185.5 m/z. As
previously mentioned, this sample was also stored in glass. Therefore, it is assumed that
Na is the ion which is attached to the product. Subtracting the mass of sodium from the
molecular ion peak yields a mass of 162.5 grams/mol. This molecular weight (162.5
grams/mol) corresponds very well with the product which is formed from the proposed
reaction mechanism #2 (162.2 grams/mol); shown in Figure 4-7. The molecular weight
of the product formed in proposed reaction mechanism #1, shown in Figure 4-5, is 180.2
grams/mol. The use of both the mass spectrum and the 1H NMR spectral data confirm
acts as an AA scavenger.
Further examination of the patent by Rule, et al50 also indicates that proposed mechanism
#2 is the correct reaction scheme. U.S. Patent 7,550,203 describes the interaction of
anthranilamide and AA, in the presence of PET, as: “combining with polyester an
bonded to carbons of the organic additive compounds, the organic additive compound
being reactive with acetaldehyde in the polyester to form water and a resulting organic
heteroatoms”. Further on in the patent50, the authors state that “the two heteroatoms are
both nitrogen”.
89
The mass spectrum shown in Figure 4-10 produces one more peak of interest; the peak at
161.5 m/z (mass to charge ratio). ESI mass spectrometry ionizes a compound by adding
an ion such as hydrogen (H), sodium (Na), etc. While ESI does not typically knock off a
hydrogen atom, if it did the peak at 161.5 m/z would correlate very well with the mass of
the product from reaction mechanism #2 (162.2 grams/mol). As just mentioned, this
phenomenon does not typically occur. In essence, a compound which has a molecular
weight of about 160 grams/mol, ionized with a hydrogen atom, would correspond with
185.5
1.0
161.5
0.6
0.4
213.5
0.2
146.5
199.4
168.1
205.6 219.6
149.4
120.4
0.0
100 120 140 160 180 200 220 m/z
Figure 4-10: ESI mass spectrum of the product from the reaction between
anthranilamide and AA in CDCl3 and methanol
90
Figure 4-11 shows a proposed reaction mechanism for anthranilamide and AA in which
the final product possesses a molecular weight of 160.2 grams/mol. Proposed reaction
mechanism #3, Figure 4-11, starts with proposed reaction mechanism #2 (Figure 4-7) but
adds one more step to the reaction. In this de-saturation reaction, the organic product
formed in reaction mechanism #2 gives off a di-hydrogen molecule that yields a similar
two-ring structured organic compound, now with a double bond in its second ring. The
formation of this final product, shown in Figure 4-11, has been observed by several
authors.89-92 Abdel-Jalil, et al89 showed that this product can be produced through the
O
O O
NH
+
NH2
H2O + H
H3C H N
H CH3
NH2
(Anthranilamide) (AA)
O
NH
H2 +
N
CH3
Beyond what was previously stated, Rule, et al50 give no further indication of the exact
composition for the resulting organic compound that is formed. Further experiments
were required to determine if proposed mechanism #3 (Figure 4-11) is more correct than
proposed mechanism #2 (Figure 4-7). This entailed periodic 1H NMR analysis to study
91
the possible double bond formation in the second ring of the organic compound produced
To begin this work, ChemSketch was used to predict a 1H NMR spectrum of the final
reaction product that is shown in Figure 4-11. Figure 4-12 shows this predicted spectrum.
Next, the sealed NMR tube which contained the dissolved mixture of anthranilamide and
AA was heated over a four week period, at 60oC. Throughout this time, periodic 1H
2.36[12]
20
O
11
7 2
8 NH
15 3
1
4 6
9
N CH3
10 5 12
10
Molecular Weight = 160.2 g/mol
5
7.67[8]
7.71[10]
7.64[9]
7.73[10]
0
10 9 8 7 6 5 4 3 2 1 0
Figure 4-12: Predicted 1H NMR spectrum for the product formed from the proposed
reaction mechanism #3 (Figure 4-11)
92
While each 1H NMR spectra confirmed the final product in proposed mechanism #2
(Figure 4-7), there proved to be no tangible evidence of the double bond formation on the
second ring. Never was there a spectrum that resembled the appearance of Figure 4-12.
It is important to note, however, that this experiment was conducted without the presence
therefore possible that the formation of the final product in proposed reaction mechanism
#3 could be obtained when anthranilamide is added to PET. All PET resins contain a
small amount of residual catalyst within their matrix. When anthranilamide is added, to
act as an AA scavenger, this residual amount of catalyst could drive the reaction to form
(MXDA) and acetaldehyde began in the same manner as previously discussed in Section
4.1.1. The initial step was to obtain the individual 1H NMR spectra for AA and MXDA.
Previously shown and discussed, Figure 4-1 shows the 1H NMR spectrum of AA
Figure 4-13 shows the 1H NMR spectrum for MXDA in the presence of deuterated
chloroform. The peaks appearing between 7.0 and 7.3 ppm are enhanced for detailed
viewing; making it easier to see the multiplicity and integration factors. It can be seen
93
that the ratio of integration factors, from left to right, is 1:1:2:4:4. Similar to
mentioned, this broad peak indicates the presence of exchangeable protons. These
protons are from MXDA’s two primary amine groups (NH2) and are represented by the
peak located at 1.35 ppm. Table 4.4 provides a list of the assigned peaks for Figure 4-13.
3.81
1
7.14
7.13
7.22
7.25
7.23
2 4
3
1.06 0.96 1.98
1.35
7.5 7.0 6.5 6.0 5.5 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5
1
Figure 4-13: H NMR spectrum of MXDA in CDCl3
Table 4.4: Peak assignment for the 1H NMR spectrum of MXDA in CDCl3
Peak Peak Integration Peak Assignment
Location Type Factor Chemical Functional Ring
(ppm) Compound Group Position
1.35 Singlet 4 MXDA Two NH2 -
3.81 Singlet 4 MXDA Two CH2 -
7.135 Doublet 2 MXDA Two CH 2
7.22 Singlet 1 MXDA CH 1
7.25 Triplet 1 MXDA CH 3
94
Similar to the mixing procedure for anthranilamide and AA, MXDA and AA were each
dissolved in separate NMR tubes using deuterated chloroform. These two individual
solutions were then combined into one tube. The mixing of the two solutions resulted in
product. Further dilution of the resulting product altered its color from orange to a dark
The appearance of this sample was similar to that of the 1 weight % MXDA/PET blend
sample; following twin-screw extrusion. The reason for this color formation was
documented by Bandi, et al.48 Through the study of polyamide/PET blends, the authors
proved that this color generation was the result of a reaction between the amine group,
from MXD6, and generated AA, from PET. This reaction results in the formation of
imine (N=CH) groups; which Bandi, et al48 proved to be the chromophores. MXDA is
the monomer from which MXD6 is manufactured. MXDA has two primary amines,
A reaction scheme between MXD6 and AA has been previously presented in Figure 2-2.
Using this as a guide, a proposed reaction mechanism for MXDA and AA is shown in
Figure 4-14. Similar to the reaction for MXD6 and AA, the aldehyde group (O=CH) of
AA reacts with a primary amine group from MXDA. Since MXDA has two primary
amine groups, one molecule of MXDA can react with up to two molecules of AA. The
result of this reaction can therefore generate up to two imine groups and up to two
95
H2N H2 C O
CH2 NH2
+ 2 H3C CH
(MXDA) (AA)
The 1H NMR spectrum representing the reaction between MXDA and AA is shown in
Figure 4-15. This spectrum contains two pieces of evidence that verify the reaction
scheme shown in Figure 4-14. First, it can be seen that the reaction forms water, evident
by the singlet at 1.90 ppm. Second, a new peak is formed at 7.80 ppm. This peak is a
quartet and represents the two imine (HC=N) groups that were the result of the reactions
between the two amine groups from MXDA and the aldehyde group from AA. Table 4.5
provides a complete list of the identified peaks that are shown in Figure 4-15.
The 1H NMR spectrum of the reaction between MXDA and AA, Figure 4-15, also shows
another interesting fact. Analysis of this spectrum shows that only two components are
present: AA and the resulting product. This indicates that any MXDA that was
originally present has since completely reacted. This is validated by the fact that the
singlet at 1.35 ppm, present in Figure 4-13, is absent in the 1H NMR spectrum shown in
Figure 4-15. This singlet represented the two primary amines of MXDA, and the absence
96
2.18
1
2.18
2 4
3
7.13
7.12
7.15
7.26
7.24
7.25
4.51
1.99
1.98
0.90 0.80 1.65
1.90
7.12
7.15
7.80
7.80
7.26
9.5 9.0 8.5 8.0 7.5 7.0 6.5 6.0 5.5 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5
Figure 4-15: 1H NMR spectrum of the reaction between MXDA and AA in CDCl3
Table 4.5: Peak assignment for the 1H NMR spectrum of the reaction between MXDA
and AA in CDCl3
Peak Peak Integration Peak Assignment
Location Type Factor Chemical Functional Ring
(ppm) Compound Group Position
1.90 Singlet - H20 -
1.985 Doublet 4.5 AA CH3 -
2.18 Doublet 6 Reaction Product Two CH3 -
4.51 Singlet 4 Reaction Product Two CH2 -
7.135 Doublet 2 Reaction Product Two CH 2
7.15 Singlet 1 Reaction Product CH 1
7.24 Singlet - Chloroform-d -
7.26 Triplet 1 Reaction Product CH 3
7.80 Quartet 2 Reaction Product Two HC=N -
9.765 Quartet 1.5 AA O=CH -
97
4.1.3 AA and Alpha-Cyclodextrin
The previously presented 1H NMR spectra for the anthranilamide and the MXDA
scavenging reactions have all used deuterated chloroform (CDCl3) as the solvent.
Deuterated chloroform is a very common solvent because it has a low boiling point, is
contains hydroxyl groups that make it a polar molecule; while CDCl3 is non-polar. The
general rule for solubility states that “like dissolves like”. In other words, alpha-
cyclodextrin will be more soluble in a polar solvent like deuterium oxide (D2O).
was initially similar to the approach discussed in Sections 4.1.1 and 4.1.2. This process
began by obtaining the individual 1H NMR spectra for alpha-cyclodextrin and AA.
Figure 4-16 shows the 1H NMR spectrum of alpha-cyclodextrin in deuterium oxide; also
shown is alpha-cyclodextrin’s repeat unit. The peaks shown in this spectrum correspond
only to the hydrogen atoms which are bonded to carbon atoms (CH groups). Not seen in
this spectrum are the hydrogen atoms bonded to oxygen atoms; hydroxyl groups. This
phenomenon is a result of the chosen solvent. The hydrogen atoms of the hydroxyl
groups are rapidly exchanged with the deuterium atoms in deuterium oxide. This
exchange causes these hydrogen atoms to be grouped into the water peak at 4.8 ppm.
98
4.80
4.80
O OH
2 OH
H H3
1 H
H4
O 5H
H6
H
6 O
OH
n
5.07
3.87
5.07
3.92
4.00
3.60
3.89
3.66
3.98
3.66
3.64
3.64
4.02
3.86
3.59
1.00 1.12 1.43 1.59 1.04
5.2 5.1 5.0 4.9 4.8 4.7 4.6 4.5 4.4 4.3 4.2 4.1 4.0 3.9 3.8 3.7 3.6 3.5
Figure 4-16: 1H NMR spectrum of alpha-cyclodextrin in D2O
In order to aid in the peak assignment for Figure 4-16, a 1H-1H NMR COSY experiment
deuterium oxide, is shown in Figure 4-17. Due to the dominant size of the water peak at
4.80 ppm, the scale of the peak intensities is very difficult to read. The coupling pattern
of this spectrum was used to assign the various peaks to their proper CH protons, within
alpha-cyclodextrin’s repeat unit. The complete peak assignment list is shown in Table
4.6.
99
3.5
3.6
3.7
3.8
3.9
4.0
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
5.0
Table 4.6: Peak assignment for the 1H NMR spectrum of alpha-cyclodextrin in D2O
Peak Peak Integration Peak Assignment
Location Type Factor Chemical Functional Ring
(ppm) Compound Group Position
3.60 Triplet 1 α-Cyclodextrin CH 4
3.61 Doublet of 1 α-Cyclodextrin CH 2
Doublets
3.83 Triplet 1 α-Cyclodextrin CH 5
3.88 Triplet 2 α-Cyclodextrin CH2 6
3.96 Triplet 1 α-Cyclodextrin CH 3
4.80 Singlet - D2O -
5.03 Doublet 1 α-Cyclodextrin CH 1
100
The 1H NMR spectrum of AA that is dissolved in deuterated chloroform has been
previously discussed and shown, in Figure 4-1. For this part of the study, however,
NMR spectrum of AA was therefore re-obtained using deuterium oxide as the solvent.
4.80
1.34
1.33
2.25
2.25
5.25
5.26
9.68
4.83
9 8 7 6 5 4 3 2 1
Figure 4-18: 1H NMR spectrum of AA in D2O
Comparing Figures 4-1 and 4-18, it can be seen that there is a dramatic difference
between the 1H NMR spectra of AA. The reason for this disparity is the result of the
solvent that is used to dissolve AA. In the presence of deuterium oxide, which is slightly
acidic, AA reacts with D2O to form an equilibrium product; as illustrated in Figure 4-19.
ChemSketch was used to predict the 1H NMR spectrum of a solution containing AA and
101
the acetal-based equilibrium product shown in Figure 4-20. This proposed equilibrium
reaction is confirmed through the comparison of the predicted 1H NMR spectrum, Figure
4-20, and the actual spectrum, Figure 4-18. The spectral patterns of these two spectra are
2 O O D
D D 3
O 4
1 H3C
H3C O D
Figure 4-19: Equilibrium reaction between AA and D2O
11
2.00[9] 1.31[6]
10
O
7
7 H3C O
8 CH3 D2O 6 3 1 D
9 2
H O
6 8a 4 D
5
3 9.33[8a] 5.78[3]
5.79[3]
2
5.81[3] 5.77[3]
1
0
10 9 8 7 6 5 4 3 2 1 0
Figure 4-20: Predicted 1H NMR spectrum of AA in D2O
102
The peak assignment list, shown in Table 4.7, corresponds to the 1H NMR spectrum of
AA in deuterium oxide, shown in 4-18. Figure 4-18 shows the approximate ratio of
integration factors, from left to right, is 1:2:3:6. Looking back at Figure 4-1, the 1H NMR
at the peak assignment in Table 4.7, the ratio of AA’s protons, within its two functional
groups, is still 1:3. The ratio for the acetal-based equilibrium product is 2:6; simplified to
be 1:3. The doubling phenomenon indicates that the equilibrium product is twice as
structures.24 This hydrophilic exterior makes water, or deuterium oxide, the solvent of
choice to dissolve cyclodextrins. The lipophilic interior makes it favorable for aldehydes
and other organics to enter its internal cavity.24, 62 As depicted in Figure 4-21, alpha-
cyclodextrin encapsulates AA into its cyclical structure without the need for a chemical
bonding.
103
Figure 4-21: Interaction mechanism for AA and alpha-cyclodextrin
Several authors71-74 have shown that 1H NMR can be used to validate cyclodextrin’s size-
similar experimental procedure was followed in an attempt to reproduce the results, seen
in Figure 2-8. In this experiment, however, alpha-cyclodextrin is the host molecule and
AA is the guest molecule. Samples were prepared by separately weighing and then
dissolving each component in D2O. These two solutions, in separate vessels, were then
combined into one NMR tube to achieve the desired molar ratios. Nine samples were
prepared in all:
• Pure alpha-cyclodextrin
• Pure AA
104
• 1 to 1 (AA to alpha-cyclodextrin)
• 2 to 1 (AA to alpha-cyclodextrin)
• 3 to 1 (AA to alpha-cyclodextrin)
The protons that were monitored during this NMR titration study were previously
identified in Figure 4-19 and Table 4.7. For AA there are two sets of protons which can
be monitored: the aldehyde proton (group 2) and the methyl protons (group 1). For the
acetal-based equilibrium product, the methyl protons (group 3) and the CH proton (group
Figure 4-22 shows the comprehensive results from the NMR titration experiment that was
contains the individual spectra from this study. This plot shows that as the concentration
AA and its equilibrium product also increase until a saturation point is reached. The
saturation point for the AA and alpha-cyclodextrin complex occurs at a one to one ratio.
This implies that every molecule of alpha-cyclodextrin can sequester only one molecule
of AA. Figure 4-22 provides the experimental proof to confirm the interaction
mechanism between AA and alpha-cyclodextrin, which has been reported for other
105
0.070
0.060
0.030
0.020
0.010
0.000
0 0.5 1 1.5 2 2.5 3 3.5
Guest to Host Ratio
Figure 4-22: Peak shifting of the protons for AA and its equilibrium product when
titrated with alpha-cyclodextrin (solvent is D2O)
PET
The second objective of this work was to investigate the efficiency of these three
amount of AA that is present in PET. The intent of these scavenging agents is not to
limit PET degradation and reduce the amount of generated AA. The purpose of adding
AA scavengers to PET is to interact with generated AA, reducing the amount that is able
106
Acetaldehyde concentrations in PET have been studied through two gas chromatography
methods. The first method quantifies the rate at which AA is generated during the
To quantify how much AA is created during processing, the AA generation rates of each
Chromatograph. Details of the gas chromatograph column and testing conditions for
varying the sample’s heating time between 9 and 17 minutes. For each sample, rates
were established at three different temperatures: 280, 290, and 300oC. This allowed for
the determination of a sample’s activation energy (EA) through the derived Arrhenius
As an example, Figure 4-23 shows the AA generations rates that were determined for the
1200 ppm anthranilamide/PET blend sample. It can be seen from this figure that the AA
generation of this sample at 280oC is around 1.0 ppm/minute. Increasing the temperature
107
by 10oC raises the rate to about 1.9 ppm/minute. At 300oC, the AA generation rate for
the 1200 ppm anthranilamide/PET blend sample is 3.0 ppm/minute. This trend
exemplifies the fact that increasing the melting/processing temperature of PET also
45.0
280 C
40.0
290 C
35.0
300 C
Acetaldehyde (ppm)
30.0
25.0
y = 2.9939x - 10.456
R2 = 0.991
20.0
y = 1.8965x - 5.3717
R2 = 0.9924
15.0
y = 1.0138x - 1.2626
R2 = 0.9278
10.0
5.0
0.0
0 5 10 15 20
Time (minutes)
Figure 4-23: AA generation plots for the 1200 ppm anthranilamide/PET blend
Plots like Figure 4-23 were prepared for each sample analyzed throughout this work: the
virgin PET sample, the extruded PET control sample, and the various AA scavenger/PET
blend samples; they are located within Appendix C. Table 4.8 lists the AA generation
rates at 280oC, 290oC, and 300oC for each sample. The general trend is that as AA
illustrated by Figures 4-24, 4-25, and 4-26. Respectively, these plots show the AA
108
generation rate as a function of scavenger concentration and temperature for the
109
9.0
8.0
280 C
Generation Rate of AA (ppm/min.)
7.0 290 C
300 C
6.0
5.0
4.0
3.0
2.0
1.0
0.0
0 2000 4000 6000 8000 10000 12000
AA Scavenger Concentration (ppm)
Figure 4-24: AA generation rate as a function of anthranilamide concentration
9.0
8.0
280 C
Generation Rate of AA (ppm/min.)
7.0 290 C
300 C
6.0
5.0
4.0
3.0
2.0
1.0
0.0
0 10000 20000 30000 40000 50000 60000
AA Scavenger Concentration (ppm)
Figure 4-25: AA generation rate as a function of alpha-cyclodextrin concentration
110
9.0
8.0
280 C
Generation Rate of AA (ppm/min.)
7.0 290 C
300 C
6.0
5.0
4.0
3.0
2.0
1.0
0.0
0 2000 4000 6000 8000 10000 12000
AA Scavenger Concentration (ppm)
Figure 4-26: AA generation rate as a function of MXDA concentration
There are two common behaviors that are observed in each of these plots (Figures 4-24,
4-25, and 4-26). The first familiar feature among these figures is that eventually the AA
generation rate becomes independent of concentration; the slope of the plot nears zero.
For MXDA this appears to happen around 1200 ppm, for anthranilamide this
phenomenon seems to occur between 1200 ppm and 10,000 ppm, and for alpha-
cyclodextrin the slope looks to flatten in the region of 10,000 ppm (or 1 weight %). The
difference between these values has to do with the molecular structure and interaction
anthranilamide and alpha-cyclodextrin can only interact with one molecule of AA.
111
The second common feature among Figures 4-24, 4-25, and 4-26, is that at 280 and
290oC there is an initial increase in the AA generation rate for each scavenging agent.
This deviation from the previously mentioned general trend is observed for the
concentrations between 0 and 1200 ppm, and the MXDA concentrations between 0 and
200 ppm. Initially, this phenomenon was attributed to experimental error in the
investigate this idea, a second control sample was produced and subsequently analyzed.
The AA generation results from this second sample upheld those from the first control
sample.
Discussed in Section 3.3 are the twin-screw extrusion experiments that melt-blended the
various scavenging agents with PET resin. Respectively, Sections 3.3.1, 3.3.2, and 3.3.3,
describe in detail how each of the various AA scavenger/PET blend samples was
prepared. Within these sections, Tables 3.1, 3.2, and 3.3 show the proportions of each
sample that was extruded once, twice, and up to three times; this general concept is
It is known that increasing a PET sample’s thermal history will also increase its amount
of the “one-time processed” PET control sample was re-extruded to establish a “two-time
processed” control sample. A portion of this “two-time processed” PET sample was then
112
extruded again to produce the “three-time processed” control sample. A more detailed
The AA generation rates of the “one-time processed”, “two-times processed”, and “three-
times processed” control samples were analyzed and are reported in Table 4.9. It can be
seen from this data that as the thermal history of the PET sample increases, so does its
AA generation rate. This information shows that the initial increase in the AA generation
rates of the lowest concentrated samples was the result of the sample preparation
methodology.
temperatures was to allow for the determination of each sample’s activation energy (EA).
Activation energy is obtained by means of the Arrhenius plot; which is derived from the
Arrhenius equation (Equation 2). The slope of this graph is the activation energy divided
by the gas constant; the y-intercept is the natural log of pre-exponential factor. Figure
4-27 shows the Arrhenius plot for the 10,000 ppm (or 1 weight %) MXDA/PET blend
sample. Similar plots were prepared for each sample and are located within Appendix D.
The comprehensive results from these individual graphs are shown in Table 4.10.
113
1.80
1.60
1.40
1.20
y = -28068x + 50.624
1.00
R2 = 0.9996
0.80
ln Rate
0.60
0.40
0.20
0.00
0.00174 0.00175 0.00176 0.00177 0.00178 0.00179 0.00180 0.00181 0.00182
-0.20
-0.40
1/Temperature (1/K)
According to the data in Table 4.10, the respective anthranilamide and MXDA blend
samples possess similar activation energies; the lone exception being the 100 ppm
samples. The similarity in values is attributed to the fact that anthranilamide and MXDA
those of anthranilamide and MXDA. This indicates that the activation energy, which
is scavenged.
114
Table 4.10 shows that four of the six evaluated alpha-cyclodextrin/PET blend samples
have higher activation energies than any other sample. This demonstrates that it takes
than it is does to break the bonds that were formed by the reaction between AA and
anthranilamide, or between AA and MXDA. Since these samples have higher activation
energies than the virgin, unprocessed PET resin the data indicates that it requires more
115
Examination of the data in Table 4.10 indicates that generally activation energy increases
with increasing scavenger concentration. In other words, the greater the concentration of
the scavenging agent, in a PET blend system, the more likely generated AA will be
sequestered and not allowed to diffuse from the polymer. Traditionally, activation
energies for PET resins have been shown to decrease with I.V. A comparison between
Tables 4.10 and 4.14, which will be discussed in Section 4.3.1.1, show that this is still
true for the virgin PET and the three extruded PET control samples. The opposite,
however, appears to be true for the various AA scavenger/PET blend samples. In this
case, activation energy appears to increase with decreasing I.V. This phenomenon is
assumed to be the combined result of both the sample blending method and the addition
of AA scavenging agents, rather than a deviation from what has been previously observed.
4.2.2 Residual AA
As AA is generated, through the degradation of PET, it has the ability to diffuse out of
the polymer. A portion of the generated AA, however, usually remains residually trapped
within the matrix of PET. Since AA is able to diffuse out of PET, even at temperatures
as low as 21oC,19 quantifying its residual concentration is important because many foods
116
samples are ground, in a liquid nitrogen environment, and then sieved to obtain a powder
that increases the diffusion ability of AA. Samples are heated at an elevated temperature,
not to melt the polymer but to volatize the residual AA that is trapped within the PET
matrix. Details of the gas chromatograph column and testing conditions for these
comprehensive results for the residual AA experiments, for both the pelletized samples
pelletized sample was collected for headspace analysis. Immediately upon collection,
this sample was place in a freezer to prevent the AA, within this PET sample, from
volatilizing. At a later point in time this sample was further prepared to be analyzed.
Table 4.11 shows the residual AA results for the various pelletized AA scavenger/PET
blend and control samples. Within this table, the effectiveness of each AA
scavenger/PET blend sample’s ability to reduce the amount of residual AA has been
quantified relative to the “one-time processed” control sample. It should also be noted
that no data is reported for the 10,000 ppm (1 weight %) anthranilamide/PET blend
sample because the entire allotment of sample was dried and crystallized prior to
headspace analysis. It was assumed that the drying and crystallization processes removed
117
Table 4.11: Residual AA data for pelletized samples
Scavenger / Number of Concentration Residual Amount of
Sample Processing (ppm) AA (ppm) Reduction (%)
Times
PET resin 0 - 0.8 -
1 - 8.9 -
Extruded PET
2 - 13.5 -
(control)
3 - 14.5 -
- 100 5.2 41.6
- 200 3.5 60.7
Anthranilamide - 500 3.0 66.3
- 1200 1.0 88.8
- 10,000 - -
- 500 5.0 43.8
- 1200 3.3 62.9
Alpha- - 5000 2.8 68.5
Cyclodextrin - 10,000 2.6 70.8
- 25,000 2.8 68.5
- 50,000 2.6 70.8
- 100 4.1 53.9
- 200 3.3 62.9
MXDA - 500 3.6 59.6
- 1200 3.4 61.8
- 10,000 2.8 68.5
It can be seen that the results shown in Table 4.11 corroborate with the general trend that
was observed for the previously discussed AA generation rate results. Generally, as the
increases. These results also indicate, as did Table 4.9, that the amount of AA (generated
or residual) increases with increasing thermal histories. The virgin PET resin, that was
not processed, has an initial residual AA concentration that is less than 1 ppm.
Processing this resin one time increases its residual AA content up to 8.9 ppm.
Processing this resin a second and then third time, increases the residual AA
118
4.2.2.2 Preform Samples
Six of the AA scavenger/PET blend samples, along with a control sample, were chosen to
be injection molded into preform samples for two reasons. The first reason was to blow-
mold a portion of these preforms in to 2-liter bottles for further analysis. The second
reason was to analyze the residual AA content, of these samples, that resulted from an
injection molding process. Table 4.12 shows the results of this work.
The results shown in Table 4.12 clearly reveal two points. The first is that the addition of
PET preforms. The second point confirms the previously observed results; the greater the
amount of scavenging agent, the greater the reduction in AA. As with Table 4.11, the
119
4.2.2.3 Comparison of Results for Pelletized Samples and Preform Samples
Table 4.13 was prepared to compare the residual AA results for similar AA
scavenger/PET blend pellet and preform samples. The sample blending process for the
preform samples varied in comparison to the blending of the pelletized samples. The
preform samples were produced by melt-blending virgin PET resin with a master-batch
sample that was passed through the twin-screw extruder only once. In the end, these
preform samples were composed of a portion that was processed once and the remaining
amount was processed twice; twin-screw extruded once and injection molded once. As
contained portions that were extruded once, twice and three times.
Table 4.13: Comparison of the residual AA data for pelletized and preform samples
Scavenger / Concentration Residual AA (ppm)
Sample (ppm) Pellets Preforms
PET - 8.9 8.3
100 5.2 4.5
Anthranilamide
200 3.5 3.7
500 5.0 4.8
Cyclodextrin
1200 3.3 4.7
100 4.1 5.3
MXDA
200 3.3 4.6
Since the scavenger concentrations for each of these sets of samples are assumed to be
the same, the comparison of their residual AA content can be made; even though their
overall thermal histories may differ. Table 4.13 shows that in most every case the
residual AA concentration is fairly similar for each respective pelletized and preform
120
sample. The one common trend in both circumstances is that the more scavenging agent,
For sensitive PET packaging applications, reducing the amount of detectable AA can be
cost of sacrificing the overall appearance and physical properties of PET. Studying
changes in the physical properties of PET was a vital step in determining the overall
benefit of adding AA scavenging agents. The properties that were analyzed to complete
this objective are: intrinsic viscosity (I.V.), color, thermal properties, and oxygen
permeability. For each type of analysis, the results for the various AA scavenger/PET
The intrinsic viscosities (I.V.) of the various AA scavenger/PET blend and PET control
were made by means of a RDA III viscoelastic tester, using parallel plate and plate
geometry. For each sample, a conversion of melt viscosity to I.V. was made through the
possessing precisely known I.V.s. Further details of this experimental setup and testing
conditions were discussed in greater detail in Section 3.6.1. All of the data from the melt
121
viscosity measurements, for both the pelletized samples and preform samples, are shown
in Appendix F.
Each AA scavenger/PET blend sample was prepared via twin-screw extrusion. During
these melt-blending procedures, a portion of each blend was set aside for melt viscosity
analysis. Prior to their evaluation, these samples were dried and crystallized overnight in
Table 4.14 shows the I.V. for each sample and its change in comparison to that of virgin
PET resin. The general trend that is shown in this table indicates that increasing
portions that have been extruded once, twice, and up to three times. It can be seen that
one pass through the twin-screw extruded degrades the PET resin enough to reduce the
I.V. by 2.5%. A second and then third time through the extruder reduces the I.V. by
This sample blending method, however, does not completely explain the loss in I.V. for
each sample. If that were the case, the “three times processed” sample should have the
122
lowest I.V. The I.V. of that sample is 0.65 dL/g; yet, the lowest I.V. (0.34 dL/g) belongs
to the 1 weight % (or 10,000 ppm) MXDA/PET blend sample. This implies that the loss
in each sample’s I.V. is due to a combination of both the addition of scavenging agents
As previously mentioned in Section 4.2.2.2, seven PET blends were injection molded into
preforms: six AA scavenger/PET blends and one control sample. Preforms of each
sample type were put aside for melt viscosity measurements. The purpose of this work
123
was to isolate the effect of AA scavenger addition on I.V.; by keeping the thermal
histories for the various AA scavenger/PET blend samples as much the same as possible.
The data in Table 4.15 shows that the anthranilamide and MXDA samples show no
reduction in I.V.; relative to the control sample (pure PET preforms). The alpha-
cyclodextrin samples, however, did show a reduction in the viscosity. The 500 ppm
alpha-cyclodextrin samples showed a 4% reduction and the 1200 ppm samples showed an
8% reduction; compared to the pure PET samples. This implies that it may be possible to
add a small amount of AA scavenging agents, less than 500 ppm, and not affect the final
I.V. of the preform. The reason the alpha-cyclodextrin/PET blend samples have a lower
I.V. than the other samples is due to the addition levels of this scavenger. As an example,
as shown in Table 4.14, when 500 ppm and 1200 ppm of anthranilamide or MXDA are
samples are lower than those of the 500 ppm and 1200 ppm alpha-cyclodextrin/PET
blend samples.
124
4.3.1.3 Comparison of Results for Pelletized Samples and Preform Samples
As previously discussed, the blending process for the preform samples varied in
comparison to the blending for the pelletized samples; in terms of each respective
sample’s overall thermal history. Since the concentrations are assumed to be the same, a
comparison of their intrinsic viscosity values can be made among these sets of samples.
Table 4.16 shows the comparison between the I.V. of the pelletized samples and preform
samples.
Table 4.16: Comparison of the I.V. data for pelletized and preform samples
Scavenger / Concentration I.V. (dL/g)
Sample (ppm) Pellets Preforms
PET - 0.78 0.76
100 0.68 0.78
Anthranilamide
200 0.68 0.78
Alpha- 500 0.73 0.73
Cyclodextrin 1200 0.71 0.70
100 0.68 0.77
MXDA
200 0.67 0.76
While, the results for the alpha-cyclodextrin samples shows no change between the
pelletized samples and the preform samples; changes in I.V. become apparent for the
anthranilamide and MXDA samples. For both of the anthranilamide samples, the
preform I.V. is 0.10 dL/g greater than the I.V. of the pellets. The same trend is true for
the two MXDA samples; this time, however, the difference in I.V. is 0.09 dL/g.
There are two reasons for the disparities seen between pelletized and preform samples for
both anthranilamide and the MXDA. The first reason, as previously mentioned, is that
125
the preform samples have less thermal history than the pelletized samples. The second
reason is due to the mechanisms by which anthranilamide and MXDA each scavenger
AA. In each of these reactions, between anthranilamide and AA (Figure 4-7 or 4-11) or
between MXDA and AA (Figure 4-14), water forms as a byproduct. It is well known that
the presence of water decreases the I.V. Since the pelletized samples have a greater
thermal history than the preform samples, there is a greater chance for more reactions
with AA and a greater chance that residual water still exists in these samples.
4.3.2 Color
Part of PET’s appeal to the food and beverage industry is the combination of its excellent
clarity and lack of color. This makes studying color generation in PET a vital step. As
scavenging agents were to generate an undesirable color within PET, it could negatively
affect the final appearance of the container and its attractiveness to the customer.
The color of PET samples can be studied by both the human eye and by analytical
plastics can be quantified. In this method a meter is utilized, similar to the one used in
this work, to measure the L, a, and b values of a crystallized polymer at room temperature.
The meaning of each of these three variables (L, a, and b) is described in Table 3.8.
Through a series of calculations these three values are then converted into Y, X%, and
126
Z%; as respectively shown in Equations 5, 6, and 7. Ultimately, the results of these
conversions are used to calculate a yellowness index (YI) for each PET sample; as shown
of the instrument, and the equations used to tabulate the results can be found in Section
3.7.
The determination of any color changes due to processing and/or AA scavenger additive
addition, were made through the use of the Hunter Lab Color/Difference Meter D25-2.
The instrument was used to analyze the crystallized PET pellets of each blend; ultimately
determining a yellowness index (YI) for each sample. Table 4.17 shows the L, a, and b
127
The results for all of the PET samples containing alpha-cyclodextrin have been omitted
from Table 4.17 because every sample had some brownness in its appearance. The
relative prominence of this color altered the L, a, and b values and inherently yielded a
false yellowness index for each alpha-cyclodextrin/PET blend sample. It can also be seen,
in Table 4.17, that processing alone affects the b value and the yellowness index. As the
number of passes through the twin-screw extruded increases, these two values also
increase. The virgin PET resin, which had not been processed, has a b value of -2.3 and a
YI of -7.2; while, the values for the “one-time processed” sample are 0.7 and 1.4,
respectively. A second and then third pass through the extruder further increases these
values.
In terms of the anthranilamide/PET blends and the MXDA/PET blends, the general trend
in Table 4.17 shows that both the b value and yellowness index increase with scavenging
were achieved when the scavenger concentration was decreased below 500 ppm. While
their b values are higher, the yellowness indexes at the 100 and 200 ppm level for both of
these scavengers are lower than that of the PET control sample that was only extruded
once. The raw data from this analysis are shown in Appendix G.
As previously mentioned, one PET control sample and six AA scavenger/PET blend
samples were injection molded into preforms. These preforms were then stretch-blow-
128
molded into 2-liter bottles. Figure 4-28 shows a representative sample for each of the
seven concentrations that were produced: 1200 ppm alpha-cyclodextrin/PET blend, 500
ppm alpha-cyclodextrin/PET blend, 200 ppm MXDA/PET blend, 100 ppm MXDA/PET
blend, 200 ppm anthranilamide/PET blend, 100 ppm anthranilamide/PET blend, and pure
have a brownish tint. The two MXDA/PET blends and the two anthranilamide/PET
blends all have an appearance that is indistinguishable from that of the pure PET bottle.
The similar appearance of these five bottles confirms the color results seen in Table 4.17.
Figure 4-28: 2-liter blow-molded PET bottles (from left to right: 1200 ppm alpha-
cyclodextrin, 500 ppm alpha-cyclodextrin, 200 ppm MXDA, 100 ppm
MXDA, 200 ppm anthranilamide, 100 ppm anthranilamide, pure PET)
dictating its end uses. These properties also determine how the material should be
129
processed. The high melting temperature of PET requires that it be extruded or injection
is above the glass transition temperature (Tg) and below the onset of crystallization. For
PET, this window is approximately between 80oC and 130oC. The moderate Tg of PET
can occur during cooling from the melt if the PET article is properly oriented. This is
The glass transition (Tg) temperature, crystallization behavior, and melting temperature of
the various PET samples were studied by differential scanning calorimetry (DSC). The
results for the assorted AA scavenger/PET blend samples were compared relative to the
results for the PET control samples; a virgin PET resin that was not extruded and an
extruded PET sample. Figure 4-29 shows an example of a typical DSC curve obtained
when a sample is heated at a rate of 10oC per minute; following a rapid quenching to
remove any crystallinity. The glass transition temperature (Tg) is shown as the small
endothermic step change in the baseline, around 80oC, in the scan. Crystallization of the
material is shown as the only exothermic peak; occurring around 140oC. Finally, the
melting behavior is also shown the prominent endothermic peak that occurred at about
235oC. Cooling the samples at a rate of 10oC per minute gave indication of their
crystallization behavior when cooled from the melt. Figure 4-30 shows an example of
this analysis, with the dominant feature being the exothermic crystallization peak that is
130
12
10
Heat Flow Endo Up (mW)
0
30 80 130 180 230 280
-2
Temperature (oC)
Figure 4-29: DSC heating curve of the 5 weight % alpha-cyclodextrin/PET blend
12
10
8
Heat Flow Endo Up (mW)
0
30 80 130 180 230 280
-2
-4
Temperature (oC)
Figure 4-30: DSC cooling curve of the 2.5 weight % alpha-cyclodextrin/PET blend
131
4.3.3.1 Glass Transition Temperature (Tg)
Table 4.18 shows the glass transition temperatures (Tg) for all of the experimental PET
samples. It should be noted that the Tg of each sample was measured during the
reheating step after being quenched from the melt. The results indicate that the addition
While there were only minor differences in the glass transition temperatures (Tg) among
the various PET samples, some changes did occur with the samples’ crystallization
132
behavior when heated from the glassy state. As shown in Table 4.19, the heat of
crystallization (delta H) values of all the processed materials are higher than that of the
virgin PET resin. This shows a greater tendency of lower molecular weight PET to
crystallize, while being reheated from the glassy state. The same conclusion can be
stated for the “peak – onset of peak” values. The “peak – onset of peak” value is a
measure of how quick a sample crystallizes and is obtained by subtracting the location of
the crystallization curve’s onset from the location of its peak. The smaller the value, the
quicker crystallization occurs. All of these numbers are lower than that of the virgin PET
resin. In terms of the crystallization peak temperature, the general trend is that the peak
temperature increases with decreasing AA scavenger concentration. This shows that the
Table 4.19: Crystallization behavior data when heating from the glassy state
Scavenger / Concentration Peak Delta H of Peak - Onset
Sample (ppm) (oC) Peak (J/g) of Peak
PET resin - 168 -18 27
Extruded PET - 160 -33 15
100 155 -34 13
200 152 -32 13
Anthranilamide 500 149 -31 11
1200 147 -32 11
10,000 150 -33 11
500 158 -33 12
1200 153 -33 12
Alpha- 5000 149 -34 10
Cyclodextrin 10,000 144 -36 10
25,000 141 -44 10
50,000 137 -22 14
100 156 -32 12
200 153 -33 13
MXDA 500 155 -34 12
1200 151 -33 11
10,000 151 -37 14
133
4.3.3.3 Melting Behavior
Analysis of the melting behavior, when heated from the glassy state, indicates that the
addition of AA scavengers to PET has little affect upon the melting peak. Table 4.20
shows that all of blended resins have similar melting peaks to that of the extruded PET
resin; due to the fact that they have all been extruded. Table 4.20 also shows that the heat
similar to the trend seen with the crystallization behavior that was previously discussed.
Table 4.20: Melting behavior data when heating from the glassy state
Scavenger / Sample Concentration (ppm) Peak (oC) Delta H of Peak (J/g)
PET resin - 223 17
Extruded PET - 229 31
100 231 32
200 227 34
Anthranilamide 500 226 32
1200 228 36
10,000 231 35
500 229 31
1200 230 32
5000 232 35
Alpha-Cyclodextrin
10,000 232 39
25,000 234 45
50,000 234 46
100 229 28
200 230 31
MXDA 500 230 32
1200 229 33
10,000 228 34
134
4.3.3.4 Crystallization Behavior When Cooling from the Melt
Table 4.21 shows the results of the crystallization behavior when cooled from the melt
for the various PET samples. The analysis of this data shows some noticeable differences
among the AA scavenger/PET blend samples. With respect to the crystallization peak
Table 4.21: Crystallization behavior data when cooling from the melt
Scavenger / Sample Concentration (ppm) Peak (oC) Delta H of Peak (J/g)
PET resin - 166 -5
Extruded PET - 162 -15
100 162 -25
200 167 -25
Anthranilamide 500 161 -15
1200 166 -28
10,000 170 -20
500 156 -15
1200 167 -24
5000 172 -29
Alpha-Cyclodextrin
10,000 176 -33
25,000 185 -44
50,000 191 -45
100 161 -17
200 167 -25
MXDA 500 161 -13
1200 162 -17
10,000 188 -26
It can also be seen, from Table 4.21, that the addition of AA scavengers has an effect
upon the heat of crystallization values. Here is where there is a definite difference among
135
the AA scavengers. With respect to the anthranilamide and the MXDA, the data for both
samples are very sporadic. No broad conclusions can be made, other than to say the
overall addition of either scavenger increases the heat of crystallization. The alpha-
cyclodextrin samples show that there is a definite trend of increasing delta H with
Oxygen permeability is a measure of how much oxygen will permeate through a sample
for a set of specified conditions. Table 4.22 shows the oxygen film permeability values
obtained from sidewall samples cut from 2-liter bottles of varying AA scavenger/PET
100 ppm anthranilamide/PET, 200 ppm anthranilamide/PET, 100 ppm MXDA/PET, and
200 ppm MXDA/PET. The data in Table 4.21 show that the oxygen permeability does
PET - 5.3
100 5.3
Anthranilamide
200 5.2
Alpha- 500 5.3
Cyclodextrin 1200 5.1
100 5.6
MXDA
200 5.4
136
4.4 Optimal AA Scavenger/PET Blends
The fourth objective of this work was to comprehensively evaluate the previously shown
data and determine the optimal AA scavenger amounts to add to PET. As previously
stated, reducing the amount of detected AA is a concern, however, not at the cost of
sacrificing the desirable properties and physical appearance of PET. The goal is to
determine the amount of AA scavengers that both minimizes the amount of detectable
AA and minimizes any possible negative effects upon the properties of PET. Evaluations
of the various AA scavenger/PET blends samples were based upon the overall analysis of
this research: AA generation rates, residual amount of AA, color, thermal properties,
A review of the data presented in Sections 4.2 and 4.3 revealed that optimal benefits of
anthranilamide addition to PET are seen at concentrations of 200 ppm or less. As shown
in Table 4.8, the 100 ppm anthranilamide/PET blend has lower AA generation rates than
the extruded PET control sample at 280 and 300oC. The 200 ppm blend has a lower rate
than the control at 300oC. Both of these blends, however, have rates higher than that of
the control sample at 290oC. The 200 ppm blend also has a higher rate at 280oC. These
anomalies are attributed to the sample blending practice which resulted in these two
blend samples having portions of up to three thermal histories; as shown in Table 3.2.
137
These 100 and 200 ppm blends also showed benefits in reducing residual AA content.
For the pelletized samples, Table 4.11 shows that adding 100 ppm and 200 ppm of
anthranilamide can have a 41.6% and 60.7% improvement, respectively, upon residual
AA concentration. When these same concentrations were achieved through the injection
molding of preforms, shown in Table 4.12, the improvement in residual AA was 45.8%
and 55.4%.
The melt-blending of 100 and 200 ppm of anthranilamide into PET has been shown to
reduce the detection of AA. Additionally, these addition levels have shown little to no
effect upon the physical properties of PET. Table 4.15 shows that the addition of up to
200 ppm of anthranilamide does not further reduce the resulting I.V. during injection
molding of preforms. There was, however, a significant decrease in the measured I.V.
for the pelletized 100 and 200 ppm/anthranilamide/PET blends; as shown in Table 4.14.
Further analysis of the 100 and 200 ppm blends indicate that these anthranilamide
addition levels result in little to no affect upon the color, thermal properties, and oxygen
permeation of the evaluated samples. Table 4.17 shows that the pelletized 100 and 200
ppm anthranilamide/PET blends actually have lower yellowness indexes than the “one-
time processed” control sample. Similarly, Figure 4-28 shows no differences among the
appearances of the 100 and 200 ppm anthranilamide/PET blend 2-liter bottles and the
138
appearance of the pure PET 2-liter bottle. Tables 4.18, 4.19, and 4.20 demonstrate that
these low anthranilamide addition levels do not alter the Tg, crystallization behavior, or
melting behavior. The only apparent influence on PET thermal properties is observed for
the heat of fusion values when the polymer blends are cooled from the melt. Table 4.21
shows that adding anthranilamide increases the delta H values in comparison to the
results obtained for the extruded control sample. Finally, Table 4.22 shows that 100 and
200 ppm of anthranilamide addition has no affect upon the oxygen permeation of PET.
Similar to anthranilamide, the optimal benefits of melt-blending MXDA into PET resin
are seen at concentrations of 200 ppm or less. The data in Table 4.8 shows that the 200
ppm MXDA/PET blend has lower AA generation rates than the control sample at each of
the three evaluated temperatures. A comparison between the 100 ppm blend and the
control sample reveals that the experimental sample has a lower rate only at 300oC. As
blending process. As shown in Table 3.3, this sample contains portions that have up to
three thermal histories; the same can be said for the 200 ppm alpha-cyclodextrin/PET
sample as well. The 100 and 200 ppm MXDA/PET blend samples contain portions
which have been pass through the twin-screw extruder once, twice, and even three times.
The control sample, by comparison, has only been extruded once. As shown in Table 4.9,
increasing the number of passes through an extruder not only increases a sample’s
139
thermal history, it also increases the degradation within that sample. This shortens the
polymer chains and increases the number of byproducts, such as AA, which are present.
The addition of 100 and 200 ppm of MXDA to PET not only reduced the apparent AA
generation rates, it also reduced the residual AA concentrations. Table 4.11 shows that
the residual AA content of the pelletized samples was lowered by 53.9% and 62.9%,
respectively, through the addition of MXDA. Analysis of the injection molded preform
samples, as shown in Table 4.12, reveals that adding 100 ppm of MXDA reduced the
comes at the detriment of the physical properties and appearance of PET. The result of
the melt viscosity measurements for the preform samples, shown in Table 4.15, indicate
that the I.V. is not further reduced through the addition of up to 200 ppm of MXDA. The
reason for the considerable I.V. decrease show in Table 4.14, for similarly concentrated
pelletized samples, was addressed previously addressed in this section and in Section
4.4.1. The 100 and 200 ppm MXDA/PET blend samples are composed of portions which
have up to three thermal histories. It has been shown in Table 4.14 that an increase in a
Further analysis of the physical properties of the 100 and 200 ppm MXDA/PET blends
show that these additive levels cause little to no change in the color, thermal properties,
and oxygen permeation. As shown in Table 4.17, these two MXDA samples have lower
140
yellowness indexes than that of the “one-time processed” control sample. Figure 4-28
illustrates that there is no visible differences among the appearances of the 100 and 200
ppm MXDA/PET blend 2-liter bottles and that of pure PET 2-liter bottle. As mentioned
for the anthranilamide samples, Tables 4.18, 4.19, and 4.20 indicate that adding small
amounts of MXDA will not affect the Tg, crystallization behavior, or melting behavior of
the PET. The only influence that adding MXDA to PET may have is the heat of fusion
value when the polymer is cooled from the melt. While Table 4.21 shows that the
addition of MXDA does increase the delta H values relative to the extruded PET control
sample, this data is sporadic and no general trend truly exists. As stated in Section 4.3.4,
the addition of MXDA shows indication of affecting the oxygen permeation of PET.
For alpha-cyclodextrin, the optimal benefits of its addition to PET are seen at
concentrations of 500 ppm or less. Table 4.8 shows that the 500 and 1200 ppm alpha-
cyclodextrin blends have lower AA generation rates at 280 and 300oC than the extruded
PET control sample. Both of their AA generation rates at 290oC, however, are higher
than that of the control sample. Previously mentioned for the anthranilamide and MXDA
samples, this is due to the blending practice which resulted in portions of these samples
Reducing the residual amount of AA was also achieved through the addition of alpha-
cyclodextrin. The addition of 500 ppm lowered the residual AA content by 43.8%, when
141
compared to the results of the control sample. Table 4.11 also shows that the 1200 ppm
alpha-cyclodextrin/PET blend reduced the residual AA content 62.9%. Table 4.12 shows
the results obtained from the residual AA analysis of injection molded preform samples.
The addition of 500 ppm of alpha-cyclodextrin reduced the AA content by 42.2%; adding
Based solely on the AA generation rates and the residual AA concentrations, it appears
that increasing the amount of alpha-cyclodextrin in PET will yield the maximum benefits.
This preliminary conclusion is again solely based on the results from the two AA
detection techniques and makes studying the changes in the physical properties and
appearance of PET a vital step toward understanding the overall threshold for melt-
Analysis of the thermal properties and oxygen permeation results for the alpha-
affected by the addition of this scavenging agent. The conclusion based on Tables 4.18,
4.19, and 4.20 indicate that adding small amounts of alpha-cyclodextrin will not affect
the Tg, crystallization behavior, or melting behavior of PET. According to Table 4.21,
alpha-cyclodextrin may influence the heat of fusion value when PET is cooled from the
melt. In fact, the data presented in that table indicate a general trend of increasing delta
Table 4.22, signify that adding up to at least 1200 ppm of alpha-cyclodextrin will not
142
Prominent changes in the physical properties and appearance of PET become an issue
when examining the I.V. and color analysis results. For anthranilamide and MXDA, it
was previously shown that the addition of these scavengers did not further reduce the I.V.
of their preform samples in comparison to the I.V. of the control sample. For alpha-
cyclodextrin, however, Table 4.15 shows that the addition of 500 and 1200 ppm of this
scavenger additionally reduced preform I.V. by 0.03 and 0.06 dL/g, respectively.
As also observed with the other two scavengers, the addition of alpha-cyclodextrin
appeared to result in a significant decrease in the I.V. for the pelletized samples. For
MXDA and anthranilamide, this result was attributed to the sample blending process;
which caused the blend samples to have increased thermal histories in comparison to the
control sample. The 500 and 1200 ppm alpha-cyclodextrin/PET blend samples were
prepared in a similar manner and had similar thermal histories to those of anthranilamide
and MXDA. The results from the preform I.V. analysis, however, indicate that the
sample blending process is not the sole reason for the decrease in the pelletized samples’
I.V. It appears that the addition of as little as 500 ppm of alpha-cyclodextrin can affect
As previously discussed in Section 4.3.2.1, the color results for each of the alpha-
cyclodextrin/PET blend samples were omitted from Table 4.17. The reason for this
omission was due to the fact that each sample had a brownish appearance that altered the
L, a, and b values and subsequently yielded a false yellowness index for each alpha-
cyclodextrin/PET blend sample. This is further illustrated by Figure 4-28, where both of
143
the alpha-cyclodextrin/PET 2-liter bottles (500 ppm and 1200 ppm) shown in this figure
have a slight brownish tint to their appearance. While the brownish appearance of the
500 ppm bottle is less than that of the 1200 ppm bottle, the appearance of the 500 ppm
The resulting color that emerges when alpha-cyclodextrin is melt-blended with PET
resulting color for even the 500 ppm alpha-cyclodextrin/PET blend had a noticeable
amount of brown color to its appearance. This result indicates that either the
4.5 Modeling
The fifth and final objective of this work was to develop a model, representing a multi-
account for the various AA scavenging mechanisms discussed in this research. This
144
Through the use of this program the addition of AA scavengers to PET can be studied in
at least two manners. The first is to compare the AA generation results for a pure PET
simulated production setting. The second way is to predict the amount of AA scavenger
either instance, the use of such a model could save time and effort by limiting the amount
Toledo’s Polymer Institute. This program models the accumulation of AA within PET
preforms that results from the melting and shear hearing experienced during an injection
constants (for the particular PET resin being analyzed) to solve the momentum and the
Several assumptions are made in order to simply the momentum equation and thermal
energy equation into the forms shown in Equations 11 and 12, respectively. This system
assumes one directional flow, the z-direction, within the injection molder’s cylindrical
channels. It also assumes that there is a constant pressure gradient and that the viscosity
of the viscous, non-Newtonian PET melt is shear dependent. The program models both
145
steady flow and intermittent flow; whichever best represents the modeled system. Radial
diffusion of AA is assumed to be negligible. The residence time within the flow channels
is too short, on the order of seconds, for the diffusion of AA to become significant. The
from that volume of material. Appendix H presents the derivation of the thermal energy
equation, through the use of these assumptions, from the general form to the one shown
in Equation 12.
∂P 1 δ ∂v
= r ×η × (Equation 11)
∂z r δr ∂r
2
∂T ∂T 1 ∂ ∂T ∂v
ρ ×Cp +v = k × r × + η (Equation 12)
∂t ∂z r ∂r ∂r ∂r
146
Table 4.24: Explanation of the terms in Equation 12
Terms Meaning
ρ Density
Cp Heat capacity
T Temperature
t Time
k Boltzmann’s constant
∂T Accumulation of heat
over time
∂t
∂T Convection
v
∂z
1 ∂ ∂T Conduction
k × r × ( k is the thermal
r ∂r ∂r
conductivity)
2 Viscous dissipation
∂v
η
∂r
Equations 11 and 12, are used along with experimentally determined rheology and AA
generation constants to predict the amount of AA that accumulates within PET preforms;
for a particular PET resin. These two equations are continuously solved for finite
volumes of space along the flow channels of a multi-cavity injection molder. Each
change from section to section as heat accumulates. The momentum equation is solved
to obtain the velocity profile. This is then used in the thermal energy equation to
determine the viscosity term. The viscosity term is subsequently used within the
momentum equation to restart this process for the next section. During this process, the
147
The rheology constants are determined through the curve-fitting of the capillary
rheometry data. The trends for this data are determined by using the general forms
shown in Equation 13 and 14. Table 4.25 provides an explanation for each term in these
equations.
(
ln(τ ) = R5 + (R3 × X ) − R4 × X 2 ) (Equation 13)
R2
X = ln(γ ) − R1 + (Equation 14)
T
Figure 4-31 shows the capillary rheometry trends for the Voridian CB12 PET resin used
in this work. The individual results are listed in Table 4.26. Evaluations were conducted
at three different temperatures (260, 270, and 280oC) so that these results could be
also developed by the University of Toledo’s Polymer Institute, was used to analyze the
data in Table 4.26. This program determined the constants needed to run the AA
148
1000
260 C
Viscosity (Pa*s)
270 C
280 C
100
10 100 1000 10000
Shear Rate (1/s)
Figure 4-31: Viscosity versus shear rate curves for the Voridian CB12 PET resin
149
Table 4.27: Rheology constants for the predictive AA generation program
R1 R2 R3 R4 R5
17.38 6600.0 0.766 0.066 14.0
The AA generation rates for this PET resin were previously shown in Table 4.8; Section
4.2.1. For this sample, an additional data point was generated that is not listed in Table
4.8. At 270oC, the Voridian CB12 PET resin generated AA at a rate of 0.3 ppm per
minute. Equation 15 describes the generation of AA in a PET. This has been determined
to be a zero order reaction, dependent only upon temperature.15 Table 4.28 provides an
explanation for the terms listed in this equation. As previously discussed, the AA
generation rates can be plotted using the derived Arrhenius equation (Equation 3) to
extrapolate these results to make predictions for temperatures beyond the ones which
were evaluated. Figure 4-32 shows the Arrhenius plot for the Voridian CB12 PET resin.
d [ AA ]
= RG (Equation 15)
dt
150
2.50
2.00
1.50
y = -33365x + 60
2
R = 0.9632
1.00
0.50
ln Rate
0.00
0.00172 0.00174 0.00176 0.00178 0.00180 0.00182 0.00184 0.00186
-0.50
-1.00
-1.50
-2.00
1/Temperature (1/K)
Figure 4-32: Arrhenius plot for the Voridian CB12 PET resin
The previously mentioned AA generation constants are determined through the results
shown in Figure 4-32. The Arrhenius plot for Voridian CB12 PET resin shows that the
slope of the trend line is 33,365 and the y-intercept is 60. These two values are used as
the constants shown in Equation 16. The y-intercept is constant aa1 and the slope is aa2.
aa 2
( aa 1 − )
RG = e T
(Equation 16)
151
Table 4.29: Explanation of the terms in Equation 16
Terms Meaning Units
RG AA generation rate for pure PET resin ppm/minute
aa1 Constant from the Arrhenius Equation ppm/minute
aa2 Constant from the Arrhenius Equation Kelvin × ppm
min .
T Temperature Kelvin
of AA within PET preforms that results from the melting and shear hearing exhibited
during an injection molding process. As molten PET moves through the flow channels in
the manifold, shear heating predominantly occurs at the surface of these cylindrical tubes.
This is further illustrated by Figure 4-33, which shows the modeling program’s prediction
channel; for ten intervals of time within a two second period. It can be seen that the
elevation of temperature is greatest near the wall surface, due to shear heating of the
viscous polymer.
152
Figure 4-33: Temperature profile as a function of radial distance from the center of a
flow channel over a two second period of time
Proximity to the flow channel’s sidewall not only affects the PET’s temperature, it also
affects its AA concentration. It has been previously discussed that shear heating and
temperature have a great influence the generation of AA within PET. As shown in Figure
4-34, this was verified using the AA generation modeling program. The results from
Figures 4-33 and 4-34 both show that the greatest effects are seen at the flow channel’s
sidewalls. Minimal influence upon temperature and AA concentration are seen at the
153
Figure 4-34: Distribution of AA as a function of radial distance from the center of the
flow channel
Within the manifold of a multi-cavity injection molder, material exits from the main flow
channel and is then split off into multiple directions. This allows several cavities to be
filled at once. This division may create an even distribution of material; however, it
Figure 4-35 shows how material is distributed to fill the four cavities on the right-hand-
side of an eight-cavity mold. The information in Figure 4-33 indicates that the material
closest to the tube’s wall builds up the most heat. This effect diminishes the closer one
gets to the center of flow channel. As PET is injected into the manifold and flows down
154
the main flow channel, material to fill cavity D is the closest to the side wall. Material to
fill cavity C is the next closest to the sidewall, then followed by the material to fill cavity
B. Material to fill cavity A comes from the center of the main flow channel and has the
lowest temperature. This statement was verified by the AA generation modeling program,
Figure 4-35: Distribution of material to fill four cavities within an eight-cavity mold
155
Figure 4-36: Temperatures for the various cavities as a function of filling times
generation program unique. The effects exhibited by a multi-cavity injection molder can
be simulated, with this program, in order to optimize machine and manifold design to
yield the best AA results possible. Evaluations can be made for a 16, a 24, a 32, or a 48
cavity system. The previously identified variables needed to run this program are
156
Table 4.30: Variables needed to run the predictive AA generation program
Variable Meaning Reason Used to
Determine
5 Rheology Constants Determined by Parameters for Viscosity
Constants Rheology Program Equations 13 and 14
aa1 Arrhenius Plot Constant (y- Parameter for RG
intercept) Equation 15
aa2 Arrhenius Plot Constant Parameter for RG
(slope) Equation 15
T Temperature (Kelvin) Parameter for RG
Equation 15
The original AA generation modeling program was developed to predict the amount of
AA that will accumulate within PET preforms due to the melting and shear heating that
occurs during injection molding. In the previous section it was shown that this is
achieved by solving the momentum and thermal energy equations along with rheology
and AA generation models. The model constants were determined explicitly for the
The original modeling program is useful for predicting the amount of AA that will be
generated within PET preforms produced from pure resin. One limitation of this system,
however, is that it is not able to account for the addition of AA scavengers added to PET
resin. The addition of scavenging agents to PET has been analyzed, discussed, and
shown to be effective in reducing the amount of detectable AA. The ability to account
for and predict the effectiveness of their addition to PET would further improve upon the
157
To begin this process, the original AA generation rate equation, shown in Equation 15,
must be modified. This equation states that the change in AA with respect to time is only
previously shown, however, that the addition of AA scavengers to PET will affect this
relationship.
When scavenging agents are added to PET, they are able to interact with the AA that is
generated during processing. This interaction does not alter the amount of AA that is
generated by the particular PET resin. It does, however, decrease the amount of AA that
to the development of Equation 17, which states that the change in the amount of
detectable AA, with respect to time, is now a function of the resin’s AA generation rate
scavenger reaction rate expression shown in Equation 17. This group of terms contains a
reaction rate constant, k1 which is a function of temperature. Also accounted for are the
concentrations of AA ([AA]), and scavenger interaction sites ([S]), and the reaction
orders (a and b) for each of these components. k1, a, and b are generic kinetic terms of
unknown quantities. For each scavenger, these terms will be determined experimentally
and fit to the rate model shown in Equation 17. Table 4.31 provides an explanation for
158
d [ AA ]
= R G − k 1 [ AA ] a [ S ] b (Equation 17)
dt
It was previously shown, in Equation 16, that the AA generation rate (RG) can be
expressed as an Arrhenius equation. The same is true for the reaction rate constant, k1 as
shown in Equation 17. The terms in Equation 18 are also defined in Table 4.32.
bb 2
( bb 1 − )
k1 = e T
(Equation 18)
159
A similar reaction rate expression can be used to describe the consumption of the AA
scavenger reaction sites; as shown in Equation 19. Both Equations 17 and 19 assume that
one molecule of AA reacts with one functional site, on an AA scavenger, to produce one
molecule of product. The 1H NMR results, discussed in Section 4.1, have shown that one
molecule of anthranilamide and alpha-cyclodextrin can only react with one molecule of
AA. Each of these scavengers has only one functional site. MXDA, however, has two
functional sites; two amine groups. 1H NMR results, Figure 4-15, indicate that one
molecule of MXDA can react with up to two molecules of AA. In other words, MXDA
One noticeable difference between these two equations is their respective reaction rate
constant. The difference between these two constants is their units. In Equation 17, k1 is
a reaction rate constant expressed in ppm (parts per million) units of mass concentration.
Converting between these two reaction rate constants can be achieved by accounting for
the difference in molecular weight between AA and the AA scavenger being analyzed.
This conversion is shown in Equation 20. Table 4.33 provides further explanation of the
d [S ]
= − k1 ' [ AA ] a [ S ]b (Equation 19)
dt
160
MW S
k1 ' = k1 ( ) (Equation 20)
MW AA
Table 4.34 is shown to review the preform residual AA results previously presented in
Table 4.12 (Section 4.2.2.2). This data is used to compare the initial AA scavenger
concentrations versus the amount of AA that is generated within the pure PET preforms;
generated AA within each preform sample. Fundamentally, this means that the AA
161
Table 4.34: Review of the residual AA data for preform samples
Scavenger / Concentration Sample’s Theoretical AA Scavenger
Sample (ppm) Residual Concentration Concentration –
AA (ppm) of AA Theoretical
Generated Concentration of
within Each Generated AA
Sample (ppm) (ppm)
PET - 8.3 -
100 4.5 91.7
Anthranilamide
200 3.7 191.7
8.3
Alpha- 500 4.8 491.7
Cyclodextrin 1200 4.7 1191.7
100 5.3 91.7
MXDA
200 4.6 191.7
temperature, allows this term to be combined with any other constants that have the same
dependency. As previously stated, the reaction rate term, k1, fits this criteria. The
combination of these terms is shown in Equation 21; yielding a new reaction rate constant,
(Equation 22) to describe the appearance of AA when AA scavengers are added to PET.
Table 4.35 provides further explanation of the terms used in both Equations 21 and 22.
k 2 = k 1 [ S 0 ]b (Equation 21)
d [ AA ]
= R G − k 2 [ AA ] a (Equation 22)
dt
162
Table 4.35: Explanation of the terms in Equations 21 and 22
Terms Meaning Units
k2 Reaction rate constant for reaction between AA and dependant on the
scavenger site, assuming constant amount of AA quantity of a and b
scavenger sites
k1 Reaction rate constant for reaction between AA and dependant on the
scavenger site quantity of a and b
[S0] Initial, constant amount of AA scavenger sites with ppm
time
b Reaction order for [S] and [S0] unitless
describing the change in AA concentration with time (Equation 15) has been replaced
with one that accounts for the addition of AA scavengers to PET. The formation of
Equation 22 simplifies this new relationship from the one previously presented in
Equation 17. The development of Equation 22 also simplifies the process to solve for the
desired variables.
The variables needed to run the original version of this AA generation modeling program
have been previously discussed and are listed in Table 4.30. The ones needed to run the
modified program are listed in Table 4.36. This list includes the terms previously
identified in Table 4.30 and the new variables needed to simulate the effects of AA
scavenger addition. Ultimately, the value of these terms will be used within the modified
AA generation modeling program to solve for the respective variables they represent.
163
Table 4.36: Variables needed to modify the predictive AA generation program
Variables Meaning Reason Used to
Determine
5 Rheology Constants Determined by Parameters for Viscosity
Constants Rheology Program Equations 13 and 14
aa1 Arrhenius Plot Constant (y- Parameter for RG
intercept) Equation 16
aa2 Arrhenius Plot Constant Parameter for RG
(slope) Equation 16
T Temperature (Kelvin) Parameter for RG and k1
Equation 16 and 18
AA Scavenger Initial Amount of AA Initial Parameter for d [ AA]
and k2
Concentration Scavenger Added to PET Equation 17 or 21 dt
Resin
a Reaction Order for Parameter for d [ AA]
Concentration of AA ([AA]) Equation 17 or 22 dt
b Reaction Order for Parameter for d [ AA]
and k2
Concentration of AA Equation 17 or 21 dt
Scavenger ([S] or [S0])
bb1 Arrhenius Plot Constant (y- Parameter for k1, k1’, and k2
intercept) Equation 18
bb2 Arrhenius Plot Constant Parameter for k1, k1’, and k2
(slope) Equation 18
The determination of the variables used to run the original predictive AA generation
program, listed in Table 4.30 (5 rheology constants, aa1, and aa2), have been previously
discussed in Section 4.5.1. These terms are also shown in Table 4.36; which lists all the
variables needed to run the modified AA generation program. The remaining terms (a, b,
bb1, and bb2) listed in this table have been added to the original modeling program to
account for the addition of AA scavenging agents to PET; creating the modified AA
generation program. These variables need to be quantified in order to run the modified
164
4.5.2.1.1 Determination of k2 and a
time, is a function of the AA generation rate of the pure PET resin minus the rate of
scavenger is constant with time. These terms are slightly reorganized to produce
Equation 23 and then expressed as a natural log function (ln) to give Equation 24.
d[AA]
Plotting ln( RG − ) versus ln([AA]) (both sets of terms are shown in Equation 24)
dt
d [ AA ]
RG − = k 2 [ AA ] a (Equation 23)
dt
d [ AA ]
ln( R G − ) = ln( k 2 ) + a × ln([ AA ]) (Equation 24)
dt
To obtain the desired sets of terms shown in Equation 24, new AA generation studies
MXDA. These new experiments were conducted because the previously presented AA
generation data, discussed in Section 4.2.1 and listed in Appendix B, contain only three
data points obtained over a short range of time (9, 13, and 17 minutes). Using these
165
parameters, it is difficult and ambiguous to fit these data sets with anything besides a
linear model. Equation 17, however, indicates that when AA scavengers are added to
These new AA generation studies evaluated the 10,000 ppm AA scavenger/PET blend
samples, for each scavenger, at 290oC for 60 minutes. Measurements were made in five
all were obtained. These evaluations provided the increased number of data points and
increased length of time necessary to better evaluate the time dependency of the rate
model; Equation 17. The results of these experiments are shown in Figures 4-37, 4-38,
and 4-39. Additionally, the data corresponding to these figures are listed in Appendix I.
Within each figure a solid line is drawn to represent the rate of AA generation for the
pure Eastman Chemical Voridian CB12 PET resin that was used in this work. Each set
of experimental data was fit with a polynomial trend-line; which will be used in
subsequent calculations. As previously seen in Section 4.2, the results in Figures 4-37,
4-38, and 4-39 indicate that the presence of AA scavengers reduces the amount of
The polynomial trend-lines, determined for each plot, are used to determine the
determined by calculating the derivative of this curve and evaluating it for each
166
d [ AA ]
= − ( 2 × c1 × time ) + c 2 (Equation 25)
dt
180.0
160.0
Experimental Data
140.0
Generation of AA for CB12 PET Resin
Acetaldehyde (ppm)
120.0
100.0
80.0
60.0 2
y = -0.0084x + 0.9771x - 5.0688
2
40.0 R = 0.9657
20.0
0.0
0 10 20 30 40 50 60
Time (minutes)
Figure 4-37: 60 minute AA generation curve for the 10,000 ppm anthranilamide/PET
blend
167
180.0
160.0
Experimental Data
140.0
Generation of AA for CB12 PET Resin
Acetaldehyde (ppm)
120.0
100.0
80.0
60.0 2
y = -0.0074x + 1.3078x - 6.9309
2
40.0 R = 0.9938
20.0
0.0
0 10 20 30 40 50 60
Time (minutes)
Figure 4-38: 60 minute AA generation curve for the 10,000 ppm alpha-
cyclodextrin/PET blend
180.0
160.0
Experimental Data
140.0
AA Generation for CB12 PET Resin
Acetaldehyde (ppm)
120.0
100.0
80.0
60.0
40.0 2
y = -0.0192x + 2.8387x - 13.252
2
R = 0.9961
20.0
0.0
0 10 20 30 40 50 60
Time (minutes)
Figure 4-39: 60 minute AA generation curve for the 10,000 ppm MXDA/PET blend
168
Beginning at the first data point (5 minutes) and continuing up to the 60 minute mark,
these d[AA] values are then subtracted from the 290oC AA generation rate of the “one-
dt
time” processed PET sample; which was previously shown to be 2.9 ppm/minute. This
sample was chosen as the control because its thermal history most closely matches those
of the experimental samples, while free from the addition of AA scavenging agents. The
d[AA]
result of this calculation yields the various RG − values. This group of terms is
dt
then expressed as a natural log function to yield the left-hand-side of Equation 24. The
Respectively, Figures 4-40, 4-41, and 4-42 show the graphs needed to determine the k2, at
290oC, and a values for anthranilamide, alpha-cyclodextrin, and MXDA. The data
slopes of these figures equal the respective a values and the y-intercepts equal the natural
d[AA]
log of k2. Equation 24 predicts that the relationship between ln RG − and
dt
ln([AA]) should be linear. Within each of these figures, however, the experimental data
shows that at high AA concentrations the trend is not linear; linearity is observed at lower
AA concentrations. One possible reason for this phenomenon is the “plateau” effect that
occurs in each of the 60 minute AA generation studies; Figures 4-37, 4-38, and 4-39. To
an extent, this effect is observed in each of these figures, but is most prominent for
d[AA]
anthranilamide. Consequently, the ln RG − vs. ln([AA]) fit, Figure 4-40, is the
dt
169
least linear among the scavengers. The best fit is for MXDA, Figure 4-42, and its 60
The results from Figures 4-40, 4-41, and 4-42 are compiled into Table 4.37; where k2 is
shown as its true value and not as ln(k2). It can be seen that the reaction rate constant (k2)
and the reaction order (a) for anthranilamide and alpha-cyclodextrin are fairly similar.
The respective terms for MXDA, however, differ greatly compared to those of the other
two scavengers. This would appear to indicate that anthranilamide and alpha-
1.20
1.00
0.80
ln (RG - (d[AA]/dt))
0.60
y = 0.1052x + 0.6569
2
R = 0.7476
0.40
0.20
0.00
-0.50 0.00 0.50 1.00 1.50 2.00 2.50 3.00 3.50
ln ([AA])
d[AA]
Figure 4-40: Plot of ln( RG − ) versus ln([AA]) for the 10,000 ppm
dt
anthranilamide/PET blend at 290oC
170
1.00
0.90
0.80
0.70
ln (RG - (d[AA]/dt))
0.60
0.50
0.40
y = 0.1042x + 0.4394
2
R = 0.8017
0.30
0.20
0.10
0.00
0.00 0.50 1.00 1.50 2.00 2.50 3.00 3.50 4.00
ln ([AA])
d[AA]
Figure 4-41: Plot of ln( RG − ) versus ln([AA]) for the 10,000 ppm alpha-
dt
cyclodextrin/PET blend at 290oC
1.00
0.50
0.00
ln (RG - (d[AA]/dt))
-0.50
-1.00
y = 0.6324x - 2.1881
2
R = 0.9408
-1.50
-2.00
ln ([AA])
d[AA]
Figure 4-42: Plot of ln( RG − ) versus ln([AA]) for the 10,000 ppm MXDA/PET
dt
blend at 290oC
171
Table 4.37: Calculated k2, for 290oC, and a value for each scavenging agent
AA Scavenger k2 at 290oC a
Anthranilamide 1.93 0.1052
Alpha-Cyclodextrin 1.55 0.1042
MXDA 0.11 0.6324
Through the use of Polymath® 6.10 software, the k2 and a values listed in Table 4.37
were used to examine how well these calculated terms fit with the experimentally
determined data points previously shown in Figures 4-37, 4-38, and 4-39. To perform
this task, the software package was set-up to solve Equation 22 for each of the three AA
scavenging agents. The respective results are shown as a dashed, green line within
Figures 4-43, 4-44, and 4-45. For each figure, there appears to be a good correlation
between the experimental data points and this predicted d[AA] curve.
dt
180.0
140.0 No Scavenger
Fitted Curve with a and k2
Acetaldehyde (ppm)
120.0
100.0
80.0
60.0
40.0
20.0
0.0
0 10 20 30 40 50 60
Time (minutes)
Figure 4-43: 60 minute AA generation data for the 10,000 ppm anthranilamide/PET
blend fitted with Equation 22, using a and k2 values
172
180.0
160.0
Experimental Data
140.0 No Scavenger
Fitted Curve with a and k2
Acetaldehyde (ppm)
120.0
100.0
80.0
60.0
40.0
20.0
0.0
0 10 20 30 40 50 60
Time (minutes)
Figure 4-44: 60 minute AA generation data for the 10,000 ppm alpha-cyclodextrin/PET
blend fitted with Equation 22, using a and k2 values
180.0
160.0
Experimental Data
140.0
No Scavenger
Fitted Curve with a and k2
Acetaldehyde (ppm)
120.0
100.0
80.0
60.0
40.0
20.0
0.0
0 10 20 30 40 50 60
Time (minutes)
Figure 4-45: 60 minute AA generation data for the 10,000 ppm MXDA/PET blend fitted
with Equation 22, using a and k2 values
173
4.5.2.1.2 Determination of k1, bb1, bb2, and b
variables (b, k1, and k2) and two independent variables. The reaction rate order, b, is
([S0]) and temperatures must be evaluated. To achieve this, the original AA generation
data that was discussed in Section 4.2.1, and shown in Appendices B and C, was used.
This data was established for each AA scavenger at temperatures of 280, 290, and 300oC
SigmaPlot® 2000 software was used to perform the multiple linear regressions. The
regression analysis was set-up to evaluate the various ln(k2) and ln([S0]) terms as
174
temperature, used during AA generation analysis, and [S0] are readily available values.
To begin these calculations, Equation 22 was used. This equation states that the change
in AA concentration, with respect to time, ( d[AA] ) is a function of the pure PET resin’s
dt
AA generation rate (RG) minus the rate of reaction between AA and the AA scavenger
(k2[AA]a). This relationship in Equation 22 has been rearranged into the form shown in
Equation 27; which is more suitable for calculating k2. To calculate the k2 values for each
AA scavenger and each of the three evaluated temperatures, d[AA] was assigned to be
dt
the respective AA generation rate for the studied AA scavenger/PET blend. RG was the
AA generation rate of the pure, “one-time” processed PET resin. Values for both of these
d [ AA ]
( RG − )
k2 = dt
(Equation 27)
[ AA ] a
The [AA]a term was obtained by raising the AA concentration, determined for each time
interval, to the appropriate a value listed in Table 4.37. For each set of conditions, AA
scavenger/PET blend concentration and temperature, the [AA]a values were averaged
among the 9, 13, and 17 minute data to obtain one value to be used in Equation 27.
An averaged value was used because, for the most part, the disparity among the [AA]a
values for the 9, 13, and 17 data was minimal and this simplified the process.
175
These series of calculations, to determine k2, were carried out for each AA scavenger at
natural log function, ln(k2), to be used in the multiple linear regression analysis. The
The multiple linear regression results are shown in Table 4.38. This table shows the b,
bb1, and bb2 terms for each AA scavenger. It was previously shown in Equation 18, that
the bb1 and bb2 terms can be used to calculate k1 values for any desired temperature.
Table 4.38: b, bb1, and bb2 values for each scavenging agent determined through
multiple linear regression
AA Scavenger b bb1 bb2
Anthranilamide 0.5421 43.93 27,080
Alpha-Cyclodextrin 0.3466 26.08 16,310
MXDA 0.2898 50.60 31,000
Figures 4-46, 4-47, and 4-48 were prepared to examine the how well the determined a, b,
bb1, and bb2 values fit their respective 290oC, 60 minute AA generation data. Similar to
the preparation of those previous figures (4-43, 4-44, and 4-45), Polymath® 6.10
software was used to solve the predictive modeling equation, Equation 17, by using the a
values, listed in Table 4.37, and b, bb1, and bb2 values, shown in Table 4.38.
176
180.0
140.0 No Scavenger
120.0
100.0
80.0
60.0
40.0
20.0
0.0
0 10 20 30 40 50 60
Time (minutes)
Figure 4-46: 60 minute AA generation data for the 10,000 ppm anthranilamide/PET
blend fitted with Equation 17; using the a, k1 at 290oC, and b values
180.0
120.0
100.0
80.0
60.0
40.0
20.0
0.0
0 10 20 30 40 50 60
Time (minutes)
Figure 4-47: 60 minute AA generation data for the 10,000 ppm alpha-cyclodextrin/PET
blend fitted with Equation 17; using the a, k1 at 290oC, and b values
177
180.0
120.0
100.0
80.0
60.0
40.0
20.0
0.0
0 10 20 30 40 50 60
Time (minutes)
Figure 4-48: 60 minute AA generation data for the 10,000 ppm MXDA/PET blend fitted
with Equation 17; using the a, k1 at 290oC, and b values
A modified form of the kinetic model is shown in Equation 28. This form is a
combination of Equations 18, 21, and 22. There are three fundamental variables for
which Equation 28 studies: temperature (bb2), the concentration of AA (a), and the AA
scavenger concentration (b). The 60 minute AA generation data was used study how the
indicates the effect of temperature and initial scavenger concentration. This set of data
was used to determine the b and bb2 terms through multiple linear regressions. Since the
bb1 term does not depend on any other variable, it is assumed to be a constant or a scaling
factor. By modifying this independent term (bb1), for each AA scavenger, the modeled
178
bb 2
d [ AA ] bb 1 −
= RG − e T
[ AA ] a [ S ] b (Equation 28)
dt
The reason the bb1 terms needed to be optimized is due to the use of multiple data sets to
determine these kinetic terms. The initial AA generation data, discussed in Section 4.2.1,
contained only three data points that were measured at between 9 and 17 minutes. This
data was fit a linear trend, indicating the sample’s AA generation rate as the slope. This
information was generated for each AA scavenger/PET blend sample at three different
temperatures.
This approach works well for a PET sample with no AA scavenger because its measured
requires only a few data points. When AA scavengers are added to PET resin, however,
this approach may need to be extended. As shown by Equation 22, the rate of change in
AA concentration changes over time. To observe this effect, more data points and longer
evaluation time was needed. To achieve this, a 60 minute AA generation study, at 290oC,
It is apparent that the 60 minute AA generation study has two advantages over the data
presented in Section 4.2.1. Not only do the evaluated AA scavenger/PET blend samples
have similar thermal histories, this study generated 12 data points for each sample. It is
therefore believed that the data obtained during the 60 minute AA generation study is the
179
more accurate representation to model against. Modifications to the bb1 values were
Once again, the Polymath® 6.10 software package was used to evaluate the governing
predictive modeling equation, represented as Equation 17. With the values listed in
Table 4.38 as starting references, alterations were made to each AA scavenger’s bb1
value until the most desired modeled curve was obtained. It is important to note that
throughout this process the a, b, and bb2 values remained unchanged. Respectively,
Figures 4-49, 4-50, and 4.51 show the results of these modifications relative to
4.39 lists the final a, b, bb1, and bb2 values for each AA scavenging agent evaluated in
this work.
180.0
140.0 No Scavenger
120.0
100.0
80.0
60.0
40.0
20.0
0.0
0 10 20 30 40 50 60
Time (minutes)
Figure 4-49: 60 minute AA generation data for the 10,000 ppm anthranilamide/PET
blend fitted with Equation 17; using the a, b, and bb2 values and 2nd
iteration bb1 value
180
180.0
120.0
100.0
80.0
60.0
40.0
20.0
0.0
0 10 20 30 40 50 60
Time (minutes)
Figure 4-50: 60 minute AA generation data for the 10,000 ppm alpha-cyclodextrin/PET
blend fitted with Equation 17; using the a, b, and bb2 values and 2nd
iteration bb1 value
180.0
120.0
100.0
80.0
60.0
40.0
20.0
0.0
0 10 20 30 40 50 60
Time (minutes)
Figure 4-51: 60 minute AA generation data for the 10,000 ppm MXDA/PET blend fitted
with Equation 17; using the a, b, and bb2 values and 2nd iteration bb1 value
181
Table 4.39: Final a, b, bb1, bb2, and k1 values for each AA scavenging agent
k1
AA Scavenger a b bb1 bb2
280oC 290oC 300oC
Anthranilamide 0.1052 0.5421 43.72 27,080 0.00532 0.01269 0.02937
Alpha-
0.1042 0.3446 26.15 16,310 0.03559 0.06008 0.09958
Cyclodextrin
MXDA 0.6324 0.2898 50.15 31,000 0.00276 0.00747 0.01951
The previously determined reaction orders (a and b) and reaction rate constant terms (bb1
and bb2), shown for each AA scavenging agent in Table 4.39, have been used within the
resin. As described earlier, this program predicts the amount of AA that will accumulate
within PET preforms during a multi-cavity injection molding process. For each AA
scavenger, a set of evaluations was conducted to study if the amount of cavities plays a
role in how effective the scavengers are in reducing the appearance of AA. Similarly, a
second set of experiments was also performed to investigate the effect of melt
temperature. The raw data for each of these studies are listed in Appendix L.
Figures 4-52, 4-53, and 4-54 respectively show the predicted AA generation results for
injection molder. Each evaluation was conducted under a standard set of conditions; the
only variable was the number of cavities filled during each simulated run. Within each of
these three figures, it can be seen that the number of cavities within an injection molder
does not affect the AA sequestering ability of any of these three scavengers.
182
70.00
60.00
Percent Decrease in AA (%)
50.00
40.00
16 Cavity - Average AA
30.00 16 Cavity - Maximum AA
24 Cavity - Average AA
24 Cavity - Maximum AA
20.00 32 Cavity - Average AA
32 Cavity - Maximum AA
48 Cavity - Average AA
10.00 48 Cavity - Maximum AA
0.00
0 2000 4000 6000 8000 10000 12000
AA Scavenger Concentration (ppm)
Figure 4-52: Predicted injection molding results for various anthranilamide/PET blends
and for various manifold designs; modeled at 280oC
80.00
70.00
Percent Decrease in AA (%)
60.00
50.00
40.00
16 Cavity - Average AA
16 Cavity - Maximum AA
30.00
24 Cavity - Average AA
24 Cavity - Maximum AA
20.00 32 Cavity - Average AA
32 Cavity - Maximum AA
10.00 48 Cavity - Average AA
48 Cavity - Maximum AA
0.00
0 10000 20000 30000 40000 50000 60000
AA Scavenger Concentration (ppm)
Figure 4-53: Predicted injection molding results for various alpha-cyclodextrin/PET
blends and for various manifold designs; modeled at 280oC
183
1.40
1.20
Percent Decrease in AA (%)
1.00
0.80
16 Cavity - Average AA
0.60
16 Cavity - Maximum AA
24 Cavity - Average AA
0.40 24 Cavity - Maximum AA
32 Cavity - Average AA
32 Cavity - Maximum AA
0.20 48 Cavity - Average AA
48 Cavity - Maximum AA
0.00
0 2000 4000 6000 8000 10000 12000
AA Scavenger Concentration (ppm)
Figure 4-54: Predicted injection molding results for various MXDA/PET blends and for
various manifold designs; modeled at 280oC
The modeling results presented in Figures 4-52 and 4-53 show that the addition of
PET preforms. According to Figure 4-54, however, the addition of MXDA to PET may
not have any effect at all upon AA concentrations. The results seen in this figure
contradict those discussed in Section 4.2; where reductions in both residual AA and the
apparent AA generation rates were observed. According to Table 4.12, as little as 100
The reason these two observations do not agree with one another is because the kinetic
parameters (a, b, bb1, and bb2) determined for MXDA/PET blends are such that there is
very little reaction initially This can be seen by comparing Figure 4-51 with 4-49 and
184
4-50. For any given point in time, the difference between the AA generation curves for
the pure PET resin and the 10,000 ppm AA scavenger/PET blends is less for MXDA than
To further illustrate this point, Polymath® 6.10 software was used to simulate the
generation of AA for times between zero and 60 seconds. Additionally, this modeling
was performed at three different temperatures; as shown in Figures 4-55, 4-56, and 4-57.
For each evaluated temperature, it can be seen that the pure PET resin and the 10,000
ppm MXDA/PET blend have very similar AA generation paths for the first 40 seconds.
This is significant because the residence time of the PET blends within the manifold of
1.8
0.8
0.6
0.4
0.2
0
0 0.2 0.4 0.6 0.8 1
Time (Minutes)
Figure 4-55: One minute simulated AA generation at 280oC
185
3.5
1.5
0.5
0
0 0.2 0.4 0.6 0.8 1
Time (Minutes)
Figure 4-56: One minute simulated AA generation at 290oC
7
10,000 ppm Alpha-Cyclodextrin
10,000 ppm MXDA
6
No Scavenger
AA (ppm)
0
0 0.2 0.4 0.6 0.8 1
Time (Minutes)
Figure 4-57: One minute simulated AA generation at 300oC
186
To study the effect of melt temperature, predictive AA generation results were obtained
by varying the temperature between 270 and 300oC; while the remaining variables were
constant throughout this process. The outcomes of this study are shown in Figures 4-58,
4-59, and 4-60. For both anthranilamide and alpha-cyclodextrin, Figures 4-58 and 4-59
show that their addition is most effective at lower melt temperatures. This effect is more
pronounced for alpha-cyclodextrin than anthranilamide. The reason for this phenomenon
has the lowest EA (136 kJ/mol), it is able to react more than the other two scavengers at
lower temperatures. The EA for anthranilamide is 225 kJ/mol; while it is 258 kJ/mol for
MXDA.
70.00
60.00
50.00
Percent Decrease in AA (%)
40.00
270 C - Average AA
30.00 270 C - Maximum AA
280 C - Average AA
280 C - Maximum AA
20.00 290 C - Average AA
290 C - Maximum AA
300 C - Average AA
10.00 300 C - Maximum AA
0.00
0 2000 4000 6000 8000 10000 12000
AA Scavenger Concentration (ppm)
Figure 4-58: Predicted injection molding results for various anthranilamide/PET blends,
studied as a function of temperature; modeled for a 48 cavity process
187
100.00
90.00
270 C - Average AA
80.00 270 C - Maximum AA
Percent Decrease in AA (%)
280 C - Average AA
70.00 280 C - Maximum AA
290 C - Average AA
60.00 290 C - Maximum AA
300 C - Average AA
50.00
300 C - Maximum AA
40.00
30.00
20.00
10.00
0.00
0 10000 20000 30000 40000 50000 60000
AA Scavenger Concentration (ppm)
Figure 4-59: Predicted injection molding results for various alpha-cyclodextrin/PET
blends, studied as a function of temperature; modeled for a 48 cavity
process
2.50
270 C - Average AA
270 C - Maximum AA
280 C - Average AA
2.00 280 C - Maximum AA
Percent Decrease in AA (%)
290 C - Average AA
290 C - Maximum AA
1.50 300 C - Average AA
300 C - Maximum AA
1.00
0.50
0.00
0 2000 4000 6000 8000 10000 12000
AA Scavenger Concentration (ppm)
Figure 4-60: Predicted injection molding results for various MXDA/PET blends, studied
as a function of temperature; modeled for a 48 cavity process
188
The results for MXDA, however, oppose those observed for anthranilamide and alpha-
cyclodextrin. Figure 4-60 shows that the greatest benefits of MXDA’s addition are seen
at higher processing temperatures. The scale, however, is so small that these temperature
differences are very small. Again, the predictive modeling of MXDA/PET blends shows
While these predicted AA generation results are modeled for a multi-cavity injection
molding system, the observed trends can still be compared to the single-cavity residual
complete correlation was not achieved. For example, the trend observed in the predicted
results indicates that the addition of MXDA to PET will not greatly reduce the
concentration of AA. The single-cavity results shown in Table 4.12, however, reveal that
the addition of 100 and 200 ppm of MXDA can reduce AA concentrations by 36.1% and
show that their addition will reduce residual AA content within PET preforms.
There are two suspected reasons as to why these data sets do not completely agree with
each other. The first, as previously stated, is that the predicted results are modeled for a
multi-cavity injection molder; while the residual AA data presented in Section 4.2.2.2
was obtained from a single-cavity injection molder. While the exact data values may not
match each other, there should still be good correlation among the observed trends from
189
The second reason as to why these data sets do not completely agree with one another is
possible error in the approach to model these AA scavengers. In other words, there are
least 12 data points. These larger data sets will be used in the
determination of the a, b, bb1, and bb2 terms. This should eliminate any
Despite the differences between the modeling results and the measured single-cavity
results, there are two statements that can be made about this initial attempt toward
Second, a detailed method was laid out in Section 4.5.2.1 to determine the identified
terms (a, b, bb1, and bb2) to describe the interactions that occur upon AA scavenger
addition to PET.
190
Chapter 5
5.1 Conclusions
The broad purpose of this work was to comprehensively study the overall effects of melt-
included studying the reactions by which these additives scavenge AA, their effectiveness
in reducing the concentrations of AA in PET articles, and any changes in the physical
properties of PET due to the addition of these scavengers. The material properties that
were studied include: thermal properties and stability, material strength and intrinsic
Through the knowledge obtained from these first three goals, a greater understanding and
the overall benefit of adding AA scavengers to PET was achieved. The compilation of
this data provided the information needed to determine the most optimal concentrations
to melt-blend these AA scavengers into PET resins. The objective was to establish AA
scavenger/PET blends that lessened the detection of AA without adversely affecting the
191
The fifth and final outcome of this project was the creation of an initial, predictive model
blend systems. This development provides a tool to analyze and compare the amounts of
AA that are generated, for both virgin PET resins and resins melt-blended with AA
scavengers, within a multiple cavity injection molder. Comparing these two scenarios
reducing the detection of AA for a simulated injection molding operation. This program
could also be used to predict the amounts of AA scavengers that are needed to melt-blend
spectrometry. Combining data from these two techniques revealed that anthranilamide
reacts with the amide and amine groups of anthranilamide to produce a two-ring, organic
This described reaction mechanism was proven by both 1H NMR and mass spectra to be
the primary AA scavenging mechanism for anthranilamide. There was, however, mass
spectroscopy evidence that indicated a further, de-saturation reaction can also occur.
192
Additional experiments were conducted to in an attempt to observe this reaction. While
these were unsuccessful, a review of literature revealed that other researchers89-92 have
made this observation. To achieve this final product, however, elevated temperatures and
a catalyst were needed. It is possible that PET processing temperatures and presence of
residual catalysts, within PET resins, could provide the necessary conditions to initiate
reaction, the aldehyde group of AA reacts with a primary amine of MXDA to create an
imine group and water, as a byproduct. The fact that MXDA possesses two primary
amine groups allows for up to two molecules of AA to react with each MXDA molecule.
If this occurs, the result is the generation of two imine groups and two molecules of water.
The generation of imine groups, from a similar AA scavenging reaction between MXD6
and AA, was proven by Bandi, et al48 to lead to the formation of a yellowish color when
melt-blending polyamides with PET. The imine formation from the MXDA and AA
reaction also lead to the creation of color. Upon mixing a solution of dissolved MXDA
with a solution of dissolved AA a solid, orange product was formed. Through further
dilution, the color was altered to a dark yellow, slight greenish tint. This final appearance
was similar to that of the 1 weight % MXDA/PET blend sample that was produced
193
The AA scavenging mechanism for alpha-cyclodextrin was determined through an NMR
titration experiment. For this work, several samples of varying alpha-cyclodextrin and
AA concentrations were prepared and analyzed by 1H NMR. Even though the mixing of
these two solutions did not result in any chemical reactions, changes still occurred in the
1
H NMR spectra. For each respective sample, the position changes of the two proton
The trends of this plot show that as the concentration of alpha-cyclodextrin increases, the
chemical shift of AA’s protons, and the equilibrium product it forms with deuterium
oxide (D2O), increase until a saturation point is reached. The saturation point for the
alpha-cyclodextrin and AA complex was found to be reached at a one to one ratio. This
means that each molecule of alpha-cyclodextrin can only scavenge one molecule of AA.
bonding/size-enclosure mechanism; which has also been reported for other host/guest
complexes.61, 71-74, 93
AA
evaluated by two gas chromatography techniques. One technique quantifies the apparent
rate of AA generation and the other technique determines the concentration of AA that
remains residually trapped in the polymer’s matrix. The results from both of these
194
techniques indicated that as the concentration of the AA scavenger increases, the amount
of detectable AA decreases.
Both tables and plots were presented to confirm the aforementioned trend that states
rates for PET blend samples. Within these data sets there are irregularities that deviate
from this generalized trend. These have been shown to be the result of the sample
blending process. The thermal history of each sample was discussed and in some cases it
was shown that portions of these samples to have had up to three thermal histories.
One common feature among these three plots is that eventually the slope becomes zero.
This means that there is a point at which the AA generation rate becomes independent of
around 1200 ppm; for alpha-cyclodextrin the slope appears to flatten in the region of
10,000 ppm, or 1 weight %. The difference between these values has to do with the
On the surface, a relative comparison among these three scavengers reveals that
was shown that, generally, at the 1200 and 10,000 ppm addition levels, by weight, the
anthranilamide/PET blend samples have lower AA generation rates than the alpha-
195
of AA scavengers in PET is based upon weight, and not on the number of moles,
When the molecular weight and the functionality of the scavengers are factored in, alpha-
cyclodextrin is actually the most efficient at reducing the generation of AA. This is based
on the fact that for an equivalent ppm concentration, the number of moles of alpha-
and/or MXDA were not shown to be seven times more efficient than alpha-cyclodextrin
at scavenging AA. Since both MXDA (136.2 g/mol)47 and anthranilamide (136.15
g/mol) have approximately the same molecular weight, their chemical structures or
functionality determine the next most efficient scavenger. It was shown that MXDA has
two primary amines for AA can react with; making it di-functional. Anthranilamide,
however, can only react with one molecule of AA. This implies that MXDA should be
twice as effective as anthranilamide; which is not what was observed. This indicates that
was shown for both pelletized and injection molded preform samples. As with the AA
generation rate data, anomalies to this general trend exist and are the result of the sample
blending process. According to the data for pelletized samples, it would again appear
that anthranilamide is the most successful at reducing the residual AA content. When
mole percentage is used in replacement of weight percentage, it is again clear that alpha-
196
cyclodextrin is the most proficient of the three scavengers at reducing AA;
Beyond just the reductions in AA, the addition of anthranilamide, MXDA, and alpha-
cyclodextrin were studied to determine the overall effects upon the physical properties
and appearance of PET. The properties that were studied include: intrinsic viscosity
(I.V.), color, thermal properties, and oxygen permeation. Determining any changes in
The I.V. data for the pelletized PET blend samples indicates that as the AA scavenger is
increased, the I.V. decreases. AA scavenger addition, however, is not the only reason for
are composed of portions that have been extruded once, twice, and up to three times.
Examination of the control samples show that a sample’s thermal history plays a role in
The roles of thermal histories and AA scavenger addition on I.V. reduction may be better
illustrated by the PET preform I.V. data. These injection molded preform samples do not
have the varying thermal histories that the pelletized samples possess. Examination of
the anthranilamide and MXDA samples indicate that the minimal addition of these two
197
scavengers do not further reduce I.V.; relative to the control sample. For alpha-
cyclodextrin, however, it appears that the addition of at least 500 ppm can affect the I.V.
The melt-blending of alpha-cyclodextrin into PET resin may not only affect the
material’s I.V., it can also affect its color. All of the alpha-cyclodextrin/PET blend
samples possessed a brownish tint that, when analytically measured, altered their L, a,
and b values and yielded a false yellowness index for each sample. The brown
appearance of the 500 and 1200 ppm alpha-cyclodextrin/PET blend samples can be seen
in 2-liter bottle samples that were manufactured. The color is especially noticeable in the
The color analysis data for the anthranilamide and MXDA samples appear to indicate that
as scavenger concentration increases, the b value and yellowness index also increase.
The impact on color, however, cannot be attributed to AA scavenger addition alone. The
color analysis data shows that increasing thermal histories will affect these values. While
their b values are higher, the yellowness indexes at the 100 and 200 ppm level for both
anthranilamide and MXDA are lower than that of the PET control sample; which was
only extruded once. This is further illustrated by the 2-liter bottle samples, as the
appearance of the 100 and 200 ppm anthranilamide or MXDA bottles are
198
It was shown that the addition of these three scavenging agents did not impact the glass
transition temperature (Tg) or melting behavior of PET. The only suspected influence
that these additives have on the thermal properties of PET is that they appear to act as
nucleating agents, making crystallization easier. Finally, it was shown that the addition
of PET.
The optimal amounts of AA scavengers to melt-blend into PET were determined through
the evaluation of the data presented in Section 4.2 and 4.3. This involved balancing the
reduction of detectable AA with any negative effects that result due to the addition of the
Results showed that increasing the AA scavenger concentration decreases both the
apparent AA generation rates and residual amount of AA with PET. The data points that
lay outside of this general trend have been shown to be the result of the sample blending
process. This methodology caused portions of these samples to have up to three thermal
histories.
199
Although results indicate that the addition of scavenging agents to PET do not greatly
affect the thermal properties or oxygen permeation, it was found that I.V. and color can
MXDA does not further reduce the I.V. during injection molding. For alpha-cyclodextrin,
however, even as little as 500 ppm reduced the I.V. by an additional 0.03 dL/g; compared
Color analysis showed that beyond 200 ppm of either anthranilamide or MXDA the
yellowness index of the PET blend sample becomes an issue. The addition of alpha-
samples had enough of a brownish tint that they were not accurately measurable. This is
further illustrated by the appearance of the 2-liter bottle samples. While the brownish
appearance of the 500 ppm bottle is less than that of the 1200 ppm bottle, the appearance
of the 500 ppm bottle would still not be acceptable for a commercial application. The
appearance of the 100 and 200 ppm anthranilamide/PET, 100 and 200 ppm MXDA/PET,
and the pure PET 2-liter bottles are indistinguishable to one another.
The data presented in this work suggests that the generation of color and decrease in I.V.
are factors that limit the addition of AA scavengers to PET. For these reasons, it is
suggested that the most optimal addition amounts for both anthranilamide and MXDA are
200 ppm or less. When adding alpha-cyclodextrin to PET, its concentration should be no
200
5.1.5 Modeling
An existing modeling program, which simulates the AA generation that occurs during
scavenging agents to PET. To quantify the interactions between the scavengers and AA,
a new modeling equation, Equation 17, was developed to describe the appearance of AA
over time. This new, governing equation utilizes four kinetic terms (a, b, bb1, and bb2) to
describe the AA and scavenger interactions. This equation contains two reaction orders, a
and b, and a reaction rate constant, k1. The reaction rate constant, a function of
temperature, is further broken down into an Arrhenius function and described by the
terms bb1 and bb2. The addition of these terms to the original modeling program allow
The methodologies to quantify the a, b, bb1, and bb2 terms for each AA scavenging agent
was also described. These values were determined through a combination of graphical
and numerical analysis techniques. The final a, b, bb1, and bb2 values have been listed
Using these terms, modeling simulations were conducted to analyze the effects that melt
temperature and number of cavities, within an injection molding set-up, have upon the
number of cavities has no impact upon the effectiveness of the AA scavengers. It was
201
shown, however, that temperature does play a role in the scavenger’s capability to reduce
The results from the multi-cavity modeling were then compared to the residual AA data
obtained from a single-cavity injection molding system. Since this predictive program is
set-up to model a different machine, the actual values were not expected to match; only
the observed trends. Both sets of experiments showed that anthranilamide and alpha-
For MXDA, however, the modeling results did not correlate with the observed trends
from the single-cavity injection molding results. The residual AA results, obtained from
the PET preforms manufactured through single-cavity injection molding, indicate that
MXDA is an effective AA scavenger; while the modeling results show only minor
changes in AA concentrations as a result of its addition. This result points toward the
conclusion that error may have occurred during the establishment of the four kinetic
terms to describe the interaction between MXDA and AA. It is suspected that this is the
result of the initial sample blending process and/or the establishment of only one set of 60
202
5.2 Recommendations
While this work provided a broad investigation toward understanding the overall effects
1. One of the identified limitations of this work was the sample blending method
of the final, desired concentrations. This process would produce blends that all
have one thermal history and that can be compared directly to one another.
2. The scavengers that were studied included two which are patented
sequester AA by mechanisms other than the ones studied in this work. These
203
include such scavengers that have been identified in this work, including
3. The version of cyclodextrin that was examined in this study was alpha-
cyclodextrin; the same is true for the work by Suloff.24 It was mentioned that
three forms of cyclodextrin exist: alpha, beta, and gamma. The reason the
alpha version was chosen is because it possesses the smallest internal cavity and
point in time.
PET was the generation of a brownish color. The appearance of this color could
intent of eliminating or managing this color formation. This could be done with
204
compatibilizers, alternate molecular structures to either increase the compound’s
5. The results presented in Section 4.5 are only theoretical and have not been
injection molding system similar to the one previously described in this work.
the experimental verification of the theoretical results obtained from this work.
this work. The goal would be to improve upon the initial model and
205
References
J.; Long, T. E., Eds. John Wiley & Sons, Ltd.: 2003; pp 31 - 115.
Resins with Reduced Viscosity Change and Containers and Other Articles
206
6. DeBruin, B. Polyester Process Using a Pipe Reactor. U.S. Patent 6906164, 2005.
2005.
2008.
10. DeBruin, B. R.; Martin, D. L. Polyester Process Using a Pipe Reactor. U.S. Patent
7074879, 2006.
11. Nelson, G. W.; Cherry, C.; Olsen, E. G. Process for Producing Polyester Articles
12. Nelson, G. W.; Nicely, V. A. Process for Producing Polyester Articles Having
51, 164-173.
207
14. Jabarin, S. A.; Lofgren, E. A., Thermal Stability of Polyethylene Terephthalate.
16. Yoda, K.; Tsuboi, A.; Wada, M.; Yamadera, R., Network Formation in
18. Delaware Health and Social Services Division of Public Health. Acetaldehyde.
2009)
19. Material Safety Data Sheet - Acetaldehyde, 99.5%. Fisher Scientific. 2005.
208
21. van Aardt, M.; Duncan, S. E.; Bourne, D.; Marcy, J. E.; Long, T. E.; Hackney, C.
R.; Heisey, C., Flavor Threshold for Acetaldehyde in Milk, Chocolate Milk, and
1381.
22. Khemani, K. C., A Novel Approach for Studying the Thermal Degradation, and
terephthalate). III. Thermal Stabilities in Terms of the Vinyl Ester End Group
Blacksburg, 2002.
25. Marshall, I.; Todd, A., The Thermal Degradation of Polyethlyene Terephthalate.
209
26. Ritchie, P. D., High Temperature Resistance and Thermal Degradation of
in Polymer Degradation, Grassie, N., Ed. Applied Science: London, 1984; Vol. 5,
p 79.
28. Kao, C.-Y.; Cheng, W.-H.; Wan, B.-Z., Investigation of Catalytic Glycolysis of
30. Granzow, A.; Ferrillo, R. G.; Wilson, A., The Effect of Elemental Red
31. Bashir, Z.; Al-Uraini, A.-A.; Jamjoom, M.; Al-Khalid, A.; Al-Hafez, M.; Ali, S.,
210
32. Long, T. E.; Bagrodia, S.; Moreau, A.; Duccase, V. Process for Improving the
34. Nelson, G. W.; Nicely, V. A.; Turner, S. R. Process for Producing Polyester PET
211
39. Mills, D. E.; Stafford, S. L. Polyamide Concentrate Useful for Producing Blends
Having Improved Flavor Retaining Property and Clarity. U.S. Patent 5340884,
1994.
40. Schumann, H.-D.; Thiele, U. Process for Direct Production of Low Acetaldehyde
41. Dalton, J. S. N.; Stafford, S. L.; Hewa, J. D. Polyester and Optical Brightener
42. Odorisio, P. A.; Andrews, S. M.; Lazzari, D.; Simon, D.; King, R. E.; Stamp, M.;
Reinicker, R.; Tinkl, M.; Berthelon, N.; Muller, D.; Hirt, U. Polyester and
6908650, 2005.
43. Odorisio, P. A.; Andrews, S. M.; Lazzari, D.; Simon, D.; King, R. E.; Stamp, M.;
Reinicker, R.; Tinkl, M.; Berthelon, N.; Muller, D.; Hirt, U. Polyester and
7022390, 2006.
9728218, 1997.
212
45. Usilton, J. J.; Andrews, S. M. Polyester Compositions of Low Residual Aldehyde
48. Bandi, S.; Mehta, S.; Schiraldi, D. A., The Mechanism of Color Generation in
49. Ferrari, G.; Sisson, E. A.; Knudsen, R. Compartmentalized Resin Pellets. U.S.
50. Rule, M.; Shi, Y.; Huang, X. Method to Decrease the Acetaldehyde Content of
213
52. Ching, T. Y.; Goodrich, J. L.; Katsumoto, K. Oxygen Scavenging System
54. Brodie, V.; Visioli, D. Aldehyde Scavenging Compositions and Methods Relating
59. Eckert, R.; Sela, M.; Munjal, S.; Nagel, M.; Voerckel, V.; Wiegner, J.-P.
214
60. Odorisio, P. A.; Andrews, S. M. Polyester Compositions of Low Residual
64. Wood, W. E.; Beaverson, N. Rigid Polymeric Beverage Bottles with Improved
65. Wood, W. E.; Beaverson, N. J. Rigid Polymeric Beverage Bottles with Improved
66. Wood, W. E.; Beaverson, N. J.; Lawonn, P.; Huang, X. Reducing Concentration
215
67. Wood, W. E.; Beaverson, N. J.; Lawonn, P.; Huang, X. Reducing Concentration
68. Wood, W. E.; Beaverson, N. J.; Lawonn, P.; Huang, X. Reducing Concentration
71. Hao, Y.-Q.; Wu, Y.; Liu, J.; Luo, G.; Yang, G., 1H NMR Study on the Inclusion
72. Lantz, A. W.; Rodriguez, M. A.; Wetterer, S. M.; Armstrong, D. W., Estimation
216
73. Inokuma, S.; Kimura, K.; Funaki, T.; Nishimura, J., Synthesis and Complexing
74. Tan, Z. J.; Zhu, X. X.; Brown, G. R., Formation of Inclusion Complexes of
2010)
78. Go, S. W.; Burzynski, D. J. Polyester Stabilization and Composition. U.S. Patent
4357461, 1982.
217
80. Rule, M. Process for Reduction of Acetaldehyde and Oxygen in Beverages
81. Rule, M.; Shi, Y. Polyester Composition and Articles with Reduced Acetaldehyde
Content and Method Using Hydrogenation Catalyst. U.S. Patent 7041350, 2006.
82. Fox, M. A.; Whitesell, J. K., Organic Chemistry. Second ed.; Jones and Bartlett
Publlishers: 1997.
Organic Compounds. Seventh ed.; John Wiley & Sons, Inc.: 2005.
84. Material Safety Data Sheet - MXDA. Mitsubishi Gas Chemical Company, Inc.
2005.
86. Material Safety Data Sheet - Anthranilamide, 99+%. Fisher Scientific. 2005.
87. ASTM Method D 1925 - Test Method for Yellowness Index of Plastics; 1988.
88. ASTM Method D 3985 - Standard Test Method for Oxygen Gas Transmission
218
89. Abdel-Jalil, R. J.; Voelter, W.; Saeed, M., A novel method for the synthesis of
90. Hanumanthu, P.; Seshavatharam, S. K. V.; Ratnam, C. V.; Subba Rao, N. V.,
92. Smith, T. A. K.; Stephen, H., Synthesis in the Quinazolone Series - VI. The
1957, 1, 38-44.
93. Chen, S.; Teng, Q.; Wu, S., Theoretical Studies on the Binding Affinities of B-
94. Fogler, H. S., Elements of Chemical Reaction Engineering. Third ed.; Prentice
1999.
219
Appendix A
1
H NMR Spectra of AA and Alpha-Cyclodextrin Titration Experiment
220
221
222
223
224
225
226
Table A.1: Location of the AA and Alpha-Cyclodextrin Protons for each of the AA and
Alpha-Cyclodextrin NMR Titration Experiments
Chemical Proton Various AA to Alpha-Cyclodextrin Ratios
Compound Group 0.000 0.211 0.426 0.613 0.800 1.006 2.016 3.026
Proton #1 5.071 5.070 5.072 5.072 5.073 5.073 5.074 5.073
Proton #2 3.653 3.653 3.653 3.654 3.655 3.655 3.656 3.656
Alpha- Proton #3 3.999 3.997 3.999 3.998 3.997 3.997 3.996 3.994
Cyclodextrin Proton #4 3.602 3.602 3.603 3.603 3.604 3.604 3.606 3.606
Proton #5 3.869 3.867 3.868 3.869 3.869 3.868 3.868 3.868
Proton #6 3.921 3.920 3.921 3.922 3.923 3.922 3.923 3.922
Methyl 2.249 2.264 2.282 2.291 2.296 2.310 2.312 2.311
AA
Aldehyde 9.685 9.699 9.719 9.724 9.738 9.744 9.747 9.748
AA’s
Methyl 1.337 1.343 1.344 1.346 1.349 1.351 1.351 1.350
Equilibrium
Product in
Aldehyde 5.254 5.259 5.260 5.262 5.264 5.266 5.266 5.267
D2O
Table A.2: Change in Location of the Protons Representing AA and its D2O Equilibrium
Product, Due to the Presence of Alpha-Cyclodextrin
Chemical Proton Various AA to Alpha-Cyclodextrin Ratios
Compound Group 0.000 0.211 0.426 0.613 0.800 1.006 2.016 3.026
Methyl 0.000 0.015 0.033 0.042 0.048 0.061 0.063 0.062
AA
Aldehyde 0.000 0.014 0.034 0.039 0.053 0.059 0.062 0.063
AA’s
Equilibrium Methyl 0.000 0.006 0.007 0.009 0.012 0.014 0.014 0.013
Product in
D2O Aldehyde 0.000 0.005 0.006 0.008 0.010 0.012 0.012 0.013
227
Appendix B
Table B.1: AA generation data for the Voridian CB12 PET resin
Temperature Time Sample Peak Calibration AA Concentration
o
( C) (minutes) Weight Area Factor (ppm)
(grams) Measured Average
0.03590 10021.33 5.3
9 0.03565 10637.06 5.6 5.3
0.02995 7912.75 5.0
0.03640 11327.21 5.9
280 13 0.04045 15090.50 7.1 6.5
0.03520 11976.80 6.4
0.03945 19272.92 9.2
17 0.04375 21695.30 9.4 9.2
0.04060 19546.90 9.1
0.03940 11647.28 5.6
9 0.04250 11753.70 5.2 5.4
0.04330 12313.72 5.4
0.04390 42196.15 18.2
290 15 0.03935 38641.15
52912
18.6 18.8
0.04180 43367.87 19.6
0.03695 45658.21 23.4
17 0.03860 51691.67 25.3 24.6
0.03890 51522.70 25.0
0.03765 22114.05 11.1
9 0.04150 25685.65 11.7 11.6
0.03765 23797.18 11.9
0.04220 64826.03 29.0
300
13 0.03915 53881.40 26.0 27.4
0.04365 62594.79 27.1
0.03305 118835.97 68.0
0.03790 125983.47 62.8
17
0.03595 112324.94 59.1
62.6
0.04385 140493.70 60.6
228
Table B.2: AA generation data for the “one-time” processed PET sample
Temperature Time Sample Peak Calibration AA Concentration
(oC) (minutes) Weight Area Factor (ppm)
(grams) Measured Average
0.03675 21561.67 11.1
9 0.05290 26224.16 9.4 10.3
0.03320 18188.71 10.4
0.03660 32478.93 16.8
280 13 0.02845 23381.53 15.5 16.0
0.03210 26570.23 15.6
0.02765 31566.38 21.6
17 0.02845 33645.70 22.4 22.8
0.03160 41023.85 24.5
0.03480 30106.83 16.4
9 0.02995 25659.67 16.2 16.1
0.03080 25741.07 15.8
0.03355 39748.23 52912 22.4
290 13 0.02935 34547.64 22.2 23.1
0.04185 54840.06 24.8
0.02480 51687.63 39.4
17 0.02525 53062.66 39.7 39.6
0.02720 57303.06 39.8
0.02750 35911.24 24.7
9 0.03710 50612.11 25.8 25.9
0.02715 39078.79 27.2
300 0.03295 97288.47 55.8
13
0.03225 97192.73 57.0
56.4
17 0.02910 139276.83 90.5 90.5
229
Table B.3: AA generation data for the “two-times” processed PET sample
Temperature Time Sample Peak Calibration AA Concentration
(oC) (minutes) Weight Area Factor (ppm)
(grams) Measured Average
0.02680 19086.90 14.8
9 0.03125 19304.59 12.9 13.7
0.03080 19881.60 13.5
0.03740 37567.37 20.9
280 13 0.03690 30734.59 17.4 19.2
0.03455 32154.95 19.4
0.03585 45155.96 26.2
17 0.04010 56210.06 29.2 28.4
0.03060 43798.33 29.8
0.02675 20099.93 15.7
9
0.02720 21411.92 16.4
16.0
0.03505 41574.96 24.7
290
13 0.02985 39945.77 27.9 27.3
0.03650 51133.55 29.2
0.04175 84840.30 42.3
17 0.03445 78842.81
47986 47.7 43.9
0.02655 53093.88 41.7
0.04300 67648.51 32.8
0.03075 40882.68 27.7
0.02615 24352.52 19.4
9
0.02900 39893.46 28.7
27.7
0.02400 27161.42 23.6
0.03185 51644.79 33.8
300 0.02780 68678.28 51.5
0.03855 104591.71 56.5
13
0.03445 90257.62 54.6
53.8
0.03960 100011.75 52.6
0.03375 145962.51 90.1
17 0.03300 159866.00 101.0 92.9
0.03745 157664.24 87.7
230
Table B.4: AA generation data for the “three-times” processed PET sample
Temperature Time Sample Peak Calibration AA Concentration
(oC) (minutes) Weight Area Factor (ppm)
(grams) Measured Average
0.03480 19983.98 12.0
9 0.03705 18711.93 10.5 11.1
0.03515 18150.14 10.8
0.03395 34505.04 21.2
280 13 0.03070 27271.89 18.5 19.8
0.03575 33724.72 19.7
0.03875 55181.86 29.7
17
0.03840 61038.78 33.1
31.4
0.03335 28107.98 17.6
9 0.03530 31510.98 18.6 17.2
0.02395 17628.15 15.3
0.03410 53302.24 32.6
290 13 0.03455 49735.29 30.0 31.1
0.03675 54171.85 30.7
0.03525 83178.72 49.2
17 0.03635 81792.24
47986 46.9 48.1
0.03540 81691.81 48.1
0.03380 46176.30 28.5
0.03505 49510.63 29.4
0.03610 43349.75 25.0
9
0.03255 45173.80 28.9
25.5
0.03945 29147.50 15.4
0.03830 47533.72 25.9
300 0.03310 97304.28 61.3
13 0.03880 117635.76 63.2 60.5
0.03450 94438.06 57.0
0.03055 136156.96 92.9
0.03485 171052.89 102.3
17
0.03220 142404.74 92.2
96.5
0.03805 180394.53 98.8
231
Table B.5: AA generation data for the 10,000 ppm anthranilamide/PET blend sample
Temperature Time Sample Peak Calibration AA Concentration
(oC) (minutes) Weight Area Factor (ppm)
(grams) Measured Average
0.02245 4249.97 3.6
9
0.02120 4245.73 3.8
3.7
0.02165 6291.43 5.5
280
13
0.02105 5852.28 5.3
5.4
0.01955 6051.81 5.9
17 0.02160 7280.81 6.4 6.1
0.02015 6508.65 6.1
0.02060 3627.16 3.3
9
0.02395 6130.99 4.8
4.1
0.02185 6725.36 5.8
290
13
0.02025 5997.03 5.6
5.7
0.02070 12793.24 11.7
17 0.02130 12423.49 52912 11.0 10.9
0.02120 11228.52 10.0
0.02040 5418.01 5.0
9 0.02085 8824.99 8.0 6.2
0.02130 6296.73 5.6
0.02140 17216.12 15.2
13 0.02230 18149.60 15.4 14.5
300 0.02210 15163.62 13.0
0.02205 25131.05 21.5
0.02005 22510.37 21.2
17 0.02175 26931.84 23.4 21.7
0.02395 25677.80 20.3
0.02265 26426.77 22.1
232
Table B.6: AA generation data for the 1200 ppm anthranilamide/PET blend sample
Temperature Time Sample Peak Calibration AA Concentration
(oC) (minutes) Weight Area Factor (ppm)
(grams) Measured Average
0.02330 9896.61 8.0
9 0.02510 11507.79 8.7 8.5
0.02505 11733.47 8.9
0.02420 14406.13 11.3
280 13 0.02260 12812.98 10.7 10.6
0.02415 12607.13 9.9
0.02535 23442.67 17.5
17 0.02290 22603.12 18.7 16.6
0.02405 17490.64 13.7
0.02355 15553.14 12.5
9 0.02515 15674.32 11.8 12.1
0.02390 15151.83 12.0
0.02345 24561.60 19.8
290 13 0.02335 22359.01
52912
18.1 18.5
0.02285 21346.96 17.7
0.02425 36310.41 28.3
17 0.02165 32864.18 28.7 27.3
0.02365 30998.15 24.8
0.02180 22027.68 19.1
9 0.02220 19628.29 16.7 17.1
0.02220 18364.02 15.6
0.02260 35213.92 29.4
0.02205 28914.71 24.8
300 13 0.02485 35418.39 26.9 27.1
0.02420 35430.54 27.7
0.02545 36231.08 26.9
0.02105 47545.93 42.7
17 0.02310 48288.46 39.5
41.1
233
Table B.7: AA generation data for 500 ppm anthranilamide/PET blend sample
Temperature Time Sample Peak Calibration AA Concentration
(oC) (minutes) Weight Area Factor (ppm)
(grams) Measured Average
0.02810 18021.34 12.1
0.03145 19407.38 11.7
9 0.02615 13790.78 10.0 11.0
0.03050 16692.38 10.3
0.02880 16376.51 10.7
0.03045 20993.01 13.0
280 0.02975 24129.28 15.3
13
0.02915 25945.29 16.8
15.7
0.02965 27567.94 17.6
0.02920 33708.79 21.8
17 0.02940 36425.88 23.4 22.4
0.03135 36548.79 22.0
0.03075 16768.51 10.3
11.3
9 0.02945 19494.97 12.5
0.02380 13985.96 11.1
0.02900 37315.08 24.3
0.02930 35571.38 22.9
290 13 0.02810 34562.32
52912 23.2 22.4
0.02875 31650.26 20.8
0.02775 30169.45 20.5
0.02895 48544.61 31.7
17 0.02775 43053.66 29.3 32.2
0.02885 54501.38 35.7
0.03080 33083.18 20.3
9 0.02860 34598.22 22.9 22.3
0.02870 36228.11 23.9
0.02950 60455.79 38.7
0.02890 74613.97 48.8
300 13 0.02960 62517.32 39.9 42.9
0.02985 68620.31 43.4
0.03075 71221.23 43.8
0.02810 120124.21 80.8
17 0.02925 93989.92 60.7 70.3
0.02860 105137.97 69.5
234
Table B.8: AA generation data for 200 ppm anthranilamide/PET blend sample
Temperature Time Sample Peak Calibration AA Concentration
(oC) (minutes) Weight Area Factor (ppm)
(grams) Measured Average
0.03030 10225.45 6.4
9 0.03165 10644.51 6.4 6.6
0.03130 11481.15 6.9
0.03140 24122.73 14.5
280 13 0.03010 22480.27 14.1 13.9
0.03205 22101.00 13.0
0.03110 34760.10 21.1
17 0.03170 34558.37 20.6 22.0
0.02985 38158.87 24.2
0.02730 10873.25 7.5
9 0.03050 14021.67 8.7 8.0
0.02960 12310.55 7.9
0.03205 46925.65 27.7
290 13 0.03115 43623.08 52912 26.5 27.7
0.03175 48448.48 28.8
0.02925 71773.69 46.4
17 0.02960 63022.82 40.2 46.0
0.02895 78874.51 51.5
0.02920 28766.98 18.6
0.02990 31040.32 19.6
9
0.03015 27853.00 17.5
18.1
0.03105 27150.27 16.5
300 0.03080 77789.41 47.7
13 0.03135 82340.70 49.6 46.8
0.02975 67856.91 43.1
0.02985 113689.79 72.0
17
0.03045 124115.41 77.0
74.5
235
Table B.9: AA generation data for 100 ppm anthranilamide/PET blend sample
Temperature Time Sample Peak Calibration AA Concentration
(oC) (minutes) Weight Area Factor (ppm)
(grams) Measured Average
0.03570 12735.22 6.7
9 0.03480 12492.80 6.8 6.9
0.03505 13341.74 7.2
0.03560 19565.94 10.4
280 13 0.03520 20124.78 10.8 10.7
0.03550 20461.39 10.9
0.03365 31584.91 17.7
17 0.03375 33297.00 18.6 18.2
0.03435 33074.75 18.2
0.03215 18921.91 11.1
9 0.03445 19842.30 10.9 11.3
0.03255 20607.85 12.0
0.03355 37765.31 52912 21.3
290 13 0.03360 39113.55 22.0 21.6
0.03385 38620.54 21.6
0.03400 70310.31 39.1
17 0.03385 74614.29 41.7 41.8
0.03420 81055.47 44.8
0.03345 36266.90 20.5
9 0.03295 33385.59 19.1 18.8
0.03355 29598.84 16.7
300 13
0.03390 87612.33 48.8
51.3
0.03540 100510.02 53.7
0.03230 133978.81 78.4
17
0.03540 148366.18 79.2
78.8
236
Table B.10: AA generation data for 50,000 ppm alpha-cyclodextrin/PET blend sample
Temperature Time Sample Peak Calibration AA Concentration
(oC) (minutes) Weight Area Factor (ppm)
(grams) Measured Average
0.02660 6595.91 4.7
9 0.03120 7747.56 4.7 4.7
0.02905 7457.12 4.9
0.02680 8188.56 5.8
280 13 0.02860 8392.27 5.5 5.8
0.02605 8455.12 6.1
0.02965 10721.99 6.8
17
0.02970 10608.79 6.8
6.8
0.02980 10112.52 6.4
9 0.03550 14179.20 7.5 6.5
0.02895 8704.33 5.7
0.02900 13060.14 8.5
290 13
0.02715 12847.98
52912 8.9
8.7
0.02910 20739.10 13.5
17 0.02765 16413.42 11.2 12.7
0.02965 20896.71 13.3
0.03210 19118.94 11.3
9 0.02795 17774.72 12.0 11.4
0.02935 16961.20 10.9
0.02940 33958.58 21.8
300 13
0.03175 29992.48 17.9
19.8
0.02755 43588.17 29.9
17 0.02630 51193.84 36.8 35.9
0.03185 69159.29 41.0
237
Table B.11: AA generation data for 25,000 ppm alpha-cyclodextrin/PET blend sample
Temperature Time Sample Peak Calibration AA Concentration
(oC) (minutes) Weight Area Factor (ppm)
(grams) Measured Average
0.03035 6540.76 4.1
9
0.02710 5377.78 3.8
3.9
0.02525 6910.67 5.2
280
13
0.02585 7437.02 5.4
5.3
0.02585 7675.39 5.6
17 0.02840 9225.79 6.1 6.1
0.02595 8795.84 6.4
0.02760 9190.52 6.3
9 0.02890 8589.87 5.6 5.9
0.02890 8802.35 5.8
0.02405 9342.69 7.3
290 13 0.02725 12520.92 8.7 7.8
0.02580 9909.52 52912 7.3
0.02505 14992.04 11.3
17 0.02895 14512.46 9.5 11.9
0.02790 21937.51 14.9
0.02605 8530.57 6.2
9 0.02865 11646.99 7.7 7.7
0.03155 15509.56 9.3
0.02765 24849.61 17.0
300 13 0.02685 28596.51 20.1 18.4
0.02665 25474.35 18.1
0.02980 56340.97 35.7
17 0.02985 61681.45 39.1 37.6
0.02435 49060.00 38.1
238
Table B.12: AA generation data for 10,000 ppm alpha-cyclodextrin/PET blend sample
Temperature Time Sample Peak Calibration AA Concentration
(oC) (minutes) Weight Area Factor (ppm)
(grams) Measured Average
0.02940 5281.10 3.4
9 0.02920 6594.27 4.3 4.1
0.02805 6963.86 4.7
0.02985 7509.68 4.8
280 13 0.02960 10526.92 6.7 5.3
0.03175 7260.41 4.3
0.03125 11185.25 6.8
17 0.02835 12178.99 8.1 7.1
0.02960 10185.59 6.5
0.03030 6860.12 4.3
9 0.02990 6806.93 4.3 4.3
0.03070 7078.03 4.4
0.03035 10375.66 6.5
290 13 0.02840 12320.47 52912 8.2 7.2
0.03035 11328.21 7.1
0.03115 22331.10 13.5
17 0.02710 20352.17 14.2 13.4
0.02855 18745.94 12.4
0.02945 11015.65 7.1
9 0.02875 9707.83 6.4 6.7
0.03040 10746.55 6.7
0.02915 26449.12 17.1
300 13
0.02730 25143.91 17.4
19.5
0.02930 35513.64 22.9
0.02650 28967.23 20.7
0.03215 77981.30 45.8
17
0.02735 54976.22 38.0
41.9
239
Table B.13: AA generation data for 5000 ppm alpha-cyclodextrin/PET blend sample
Temperature Time Sample Peak Calibration AA Concentration
(oC) (minutes) Weight Area Factor (ppm)
(grams) Measured Average
0.03370 4028.45 2.3
9 0.03180 4449.18 2.6 2.7
0.02635 4498.99 3.2
0.03410 8351.80 4.6
280 13 0.03115 8591.22 5.2 4.9
0.03045 7872.67 4.9
0.02915 9293.40 6.0
17 0.03275 11399.70 6.6 6.7
0.03075 12166.39 7.5
0.02830 8853.82 5.9
9 0.02935 8248.81 5.3 5.7
0.03090 9842.70 6.0
0.03220 19480.79 11.4
290 13 0.03045 19106.01 52912 11.9 11.3
0.03120 17479.80 10.6
0.02990 33492.25 21.2
17 0.03185 33031.97 19.6 20.0
0.03135 31897.86 19.2
0.03175 16590.18 9.9
9 0.03375 20325.06 11.4 9.7
0.03085 12915.65 7.9
0.03275 34816.97 20.1
300 13 0.03395 36154.95 20.1 20.7
0.03150 36298.49 21.8
0.03420 82093.43 45.4
17 0.02830 57303.69 38.3 43.3
0.03310 81164.35 46.3
240
Table B.14: AA generation data for 1200 ppm alpha-cyclodextrin/PET blend sample
Temperature Time Sample Peak Calibration AA Concentration
(oC) (minutes) Weight Area Factor (ppm)
(grams) Measured Average
0.03275 10353.17 6.0
9 0.03450 9201.02 5.0 5.4
0.03110 8691.70 5.3
0.03280 20289.26 11.7
13 0.03115 18825.27 11.4 11.7
280 0.02920 18719.20 12.1
0.03305 22355.14 12.8
0.03210 21024.08 12.4
17 0.03250 19807.18 11.5 12.0
0.03015 18523.24 11.6
0.03235 19769.17 11.5
0.02990 12760.17 8.1
9 0.03165 13754.56 8.2 7.9
0.03315 13207.64 7.5
0.03170 22940.03 13.7
290 13 0.02925 22020.73
52912 14.2 14.6
0.03065 25651.33 15.8
0.03245 57244.16 33.3
17 0.03385 60454.90 33.8 33.1
0.03345 57115.96 32.3
0.03125 23378.92 14.1
9 0.03190 26013.59 15.4 14.3
0.02945 20654.78 13.3
0.03305 56562.87 32.3
0.03095 53728.78 32.8
300 13
0.03265 65121.31 37.7
34.5
0.03035 56663.26 35.3
0.03000 90427.19 57.0
17 0.03205 117884.86 69.5 63.7
0.03300 112926.56 64.7
241
Table B.15: AA generation data for 500 ppm alpha-cyclodextrin/PET blend sample
Temperature Time Sample Peak Calibration AA Concentration
(oC) (minutes) Weight Area Factor (ppm)
(grams) Measured Average
0.03540 12693.84 6.8
9 0.03355 11745.19 6.6 6.6
0.03535 12102.76 6.5
0.03170 23279.11 13.9
280 13 0.03505 24231.11 13.1 13.3
0.03355 23261.63 13.1
0.03680 33651.79 17.3
17 0.03645 34374.17 17.8 17.5
0.03445 31610.63 17.3
0.03545 19266.52 10.3
9 0.03360 19989.25 11.2 10.3
0.03310 16684.28 9.5
0.03490 39173.70 21.2
0.03405 38066.63 21.1
13
0.03530 42430.24 22.7
22.5
290 0.03405 44991.92
52912 25.0
0.03455 77099.50 42.2
0.03570 82365.18 43.6
17 0.03435 74410.02 40.9 42.2
0.03350 76266.25 43.0
0.03470 75943.04 41.4
0.03445 31196.78 17.1
9 0.03130 33359.75 20.1 19.3
0.03235 35547.25 20.8
0.03650 83803.01 43.4
300 13 0.03365 76059.88 42.7 42.6
0.03530 78098.14 41.8
0.03575 134801.71 71.3
17 0.03440 155068.99 85.2 77.0
0.03085 121579.66 74.5
242
Table B.16: AA generation data for 10,000 ppm MXDA/PET blend sample
Temperature Time Sample Peak Calibration AA Concentration
(oC) (minutes) Weight Area Factor (ppm)
(grams) Measured Average
0.01915 10754.44 10.6
9 0.02440 10904.45 8.4 9.5
0.02775 13664.13 9.3
0.02880 22799.00 15.0
280 13 0.02750 22376.95 15.4 15.6
0.02600 22565.43 16.4
0.03050 26850.58 16.6
17 0.03000 26629.59 16.8 16.5
0.02510 21336.00 16.1
0.01520 9012.27 11.2
9 0.02335 12347.19 10.0 10.9
0.02545 15505.40 11.5
0.02680 28529.24 20.1
290 13
0.02675 31445.05
52912 22.2
21.2
0.02605 40309.15 29.2
17 0.02795 45428.41 30.7 28.8
0.02320 32385.49 26.4
0.03255 31877.31 18.5
9 0.03005 34953.07 22.0 20.0
0.01910 19864.26 19.7
0.02755 57753.20 39.6
300 13
0.02650 55280.63 39.4
37.9
0.02870 52144.27 34.3
0.02395 48557.32 38.3
0.02735 89201.85 61.6
17
0.02845 91998.16 61.1
61.4
243
Table B.17: AA generation data for 1200 ppm MXDA/PET blend sample
Temperature Time Sample Peak Calibration AA Concentration
(oC) (minutes) Weight Area Factor (ppm)
(grams) Measured Average
0.02640 6649.77 4.8
9 0.02620 7235.20 5.2 5.0
0.02750 7401.17 5.1
0.02680 18914.67 13.3
280 13
0.02530 17367.92 13.0
13.2
0.02735 21933.95 15.2
17 0.02460 21345.86 16.4 15.8
0.02470 20843.12 15.9
0.02430 13497.20 10.5
9 0.02510 14573.04 11.0 11.2
0.02670 17207.69 12.2
0.02710 23537.10 16.4
290 13
0.02605 24523.26 52912 17.8
17.1
0.02955 49215.59 31.5
17 0.02755 43674.35 30.0 30.5
0.02500 39667.18 30.0
0.03005 36184.83 22.8
9 0.02825 33937.10 22.7 22.8
0.02435 29587.95 23.0
0.02695 55417.39 38.9
300 13 0.02620 62362.74 45.0 40.8
0.02755 55980.98 38.4
0.02640 76308.92 54.6
17 0.02635 82921.32 59.5 63.0
0.02650 104928.60 74.8
244
Table B.18: AA generation data for 500 ppm MXDA/PET blend sample
Temperature Time Sample Peak Calibration AA Concentration
(oC) (minutes) Weight Area Factor (ppm)
(grams) Measured Average
0.02765 13191.44 9.0
0.02820 12492.65 8.4
9 0.02525 13328.85 10.0 9.6
0.02555 14422.95 10.7
0.02705 14393.95 10.1
0.03065 20966.06 12.9
0.02830 20708.67 13.8
0.02745 20939.59 14.4
280 0.02665 17507.10 12.4
13
0.02790 19088.11 12.9
13.4
0.02780 19932.43 13.6
0.02835 21572.78 14.4
0.02645 17871.96 12.8
0.02885 36947.35 24.2
0.02780 30677.74 20.9
17
0.02780 31587.87 21.5
21.9
0.02790 31245.72 21.2
0.02590 16052.88 11.7
0.02700 18553.96
52912 13.0
9
0.02690 18183.49 12.8
12.0
0.02740 15284.85 10.5
0.02775 32819.58 22.4
290 13 0.02945 37924.79 24.3 23.7
0.03030 39276.05 24.5
0.02810 42378.80 28.5
17 0.02605 41239.44 29.9 30.6
0.02585 45655.78 33.4
0.02675 25835.95 18.3
0.02785 25942.89 17.6
9
0.02865 33708.15 22.2
20.5
0.02575 32832.29 24.1
300 13
0.02850 62757.82 41.6
40.8
0.02760 58393.91 40.0
0.02645 92609.84 66.2
17 0.02980 105440.67 66.9 63.9
0.02695 83682.10 58.7
245
Table B.19: AA generation data for 200 ppm MXDA/PET blend sample
Temperature Time Sample Peak Calibration AA Concentration
(oC) (minutes) Weight Area Factor (ppm)
(grams) Measured Average
0.03445 16212.06 8.9
9 0.03310 15477.49 8.8 8.9
0.03495 16748.32 9.1
0.03720 28532.02 14.5
280 13 0.03495 26934.12 14.6 14.8
0.03345 27149.13 15.3
0.03345 41604.17 23.5
17 0.03515 34630.82 18.6 20.7
0.03335 35111.05 19.9
0.03395 21221.74 11.8
9 0.03465 22229.38 12.1 12.6
0.03410 24742.35 13.7
0.03270 43249.72 25.0
290 13 0.03470 39944.27 52912 21.8 24.0
0.03515 46892.40 25.2
0.03385 58241.69 32.5
17 0.03295 57959.91 33.2 33.0
0.03330 58616.22 33.3
0.03235 28788.19 16.8
9 0.03525 36024.56 19.3 18.5
0.03515 35902.69 19.3
0.03095 60134.01 36.7
300 13 0.03430 69062.89 38.1 39.3
0.03610 82593.73 43.2
0.03295 122668.66 70.4
17 0.03320 116086.15 66.1 67.4
0.03290 114399.97 65.7
246
Table B.20: AA generation data for 100 ppm MXDA/PET blend sample
Temperature Time Sample Peak Calibration AA Concentration
(oC) (minutes) Weight Area Factor (ppm)
(grams) Measured Average
0.03710 20894.29 10.6
9 0.03535 20557.17 11.0 10.4
0.03525 17958.63 9.6
0.03460 33680.88 18.4
0.03390 33325.23 18.6
0.03235 32686.28 19.1
280 13
0.03315 32775.89 18.7
18.4
0.03440 32475.79 17.8
0.03295 31438.10 18.0
0.03695 51837.08 26.5
17 0.03650 47193.62 24.4 24.5
0.03450 40945.71 22.4
0.03190 22810.96 13.5
0.03580 23400.97 12.4
9
0.03335 25164.79 14.3
13.5
0.03690 27110.60 13.9
0.03285 42073.29 24.2
0.03790 50437.61 52912 25.2
0.03240 39126.95 22.8
290 13
0.03410 43681.92 24.2
23.8
0.03680 44574.51 22.9
0.03455 42487.90 23.2
0.03355 91214.95 51.4
0.03440 92538.91 50.8
17
0.03525 96388.32 51.7
50.5
0.03465 87926.34 48.0
0.03505 34816.07 18.8
9 0.03330 32006.28 18.2 18.7
0.03490 35129.44 19.0
0.03405 93445.80 51.9
300 13 0.03405 92382.33 51.3 51.3
0.03410 91450.67 50.7
0.03625 132755.61 69.2
17 0.03405 138677.16 77.0 73.1
0.03365 130307.69 73.2
247
Appendix C
AA Generation Plots
70.0
280 C
60.0
290 C
50.0 300 C
Acetaldehyde (ppm)
40.0
y = 6.3768x - 49.045
2
R = 0.954
30.0
y = 2.3578x - 15.977
2
R = 0.9968
20.0
y = 0.4915x + 0.6075
2
R = 0.9459
10.0
0.0
0 5 10 15 20
Time (minutes)
Figure C-1: AA generation plots for the Voridian CB12 PET resin
248
100.0
90.0
80.0 280 C
290 C
70.0
Acetaldehyde (ppm)
300 C
60.0
10.0
0.0
0 5 10 15 20
Time (minutes)
Figure C-2: AA generation plots for the “one-time” processed PET sample
100.0
90.0
280 C
80.0 290 C
70.0 300 C
Acetaldehyde (ppm)
60.0
y = 8.1602x - 47.946
2
R = 0.987
50.0
y = 3.4842x - 16.226
2
R = 0.9876
40.0
y = 1.8384x - 3.4389
2
R = 0.9794
30.0
20.0
10.0
0.0
0 5 10 15 20
Time (minutes)
Figure C-3: AA generation plots for the “two-times” processed PET sample
249
100.0 280 C
290 C
80.0 300 C
Acetaldehyde (ppm)
y = 8.8765x - 54.546
2
R = 0.9999
60.0
y = 3.8605x - 18.08
2
R = 0.9968
40.0
y = 2.5396x - 12.258
2
R = 0.9932
20.0
0.0
0 5 10 15 20
Time (minutes)
Figure C-4: AA generation plots for the “three-times” processed PET sample
25.0
280 C
290 C
20.0
300 C
y = 1.9366x - 11.038
Acetaldehyde (ppm)
2
R = 0.9982
15.0
y = 0.8527x - 4.187
2
R = 0.9162
10.0
y = 0.3034x + 1.1103
2
R = 0.9508
5.0
0.0
0 5 10 15 20
Time (minutes)
Figure C-5: AA generation plots for the 10,000 ppm anthranilamide/ PET blend sample
250
90.0
280 C
80.0
290 C
70.0
300 C
Acetaldehyde (ppm)
60.0
50.0
y = 5.9991x - 32.787
2
R = 0.9933
40.0
y = 2.6164x - 12.04
2
R = 0.9989
30.0
y = 1.4318x - 2.2536
2
R = 0.9898
20.0
10.0
0.0
0 5 10 15 20
Time (minutes)
Figure C-6: AA generation plots for the 500 ppm anthranilamide/ PET blend sample
80.0
70.0
280 C
290 C
60.0
300 C
Acetaldehyde (ppm)
50.0
40.0
y = 7.0565x - 45.271
2
R = 0.9999
30.0
y = 4.7512x - 34.526
2
R = 0.9996
20.0
y = 1.9258x - 10.9
2
R = 0.9992
10.0
0.0
0 5 10 15 20
Time (minutes)
Figure C-7: AA generation plots for the 200 ppm anthranilamide/ PET blend sample
251
80.0
70.0 280 C
290 C
60.0
300 C
Acetaldehyde (ppm)
50.0
40.0
y = 7.5038x - 47.941
2
R = 0.9978
30.0
y = 3.815x - 24.668
2
R = 0.9658
20.0
y = 1.4109x - 6.4099
2
R = 0.9652
10.0
0.0
0 2 4 6 8 10 12 14 16 18 20
Time (minutes)
Figure C-8: AA generation plots for the 100 ppm anthranilamide/ PET blend sample
45.0
280 C
40.0
290 C
35.0 300 C
Acetaldehyde (ppm)
30.0
25.0
y = 3.0638x - 17.446
2
R = 0.9687
20.0
y = 0.7651x - 0.6319
2
R = 0.9731
15.0
y = 0.2561x + 2.4553
2
R = 0.9992
10.0
5.0
0.0
0 5 10 15 20
Time (minutes)
Figure C-9: AA generation plots for the 50,000 ppm alpha-cyclodextrin/ PET blend
sample
252
40.0
35.0
280 C
30.0
290 C
Acetaldehyde (ppm)
25.0 300 C
y = 3.7375x - 27.343
2
R = 0.9734
20.0
y = 0.7491x - 1.2275
2
R = 0.9552
15.0
y = 0.2676x + 1.6111
2
R = 0.9706
10.0
5.0
0.0
0 5 10 15 20
Time (minutes)
Figure C-10: AA generation plots for the 25,000 ppm alpha-cyclodextrin/ PET blend
sample
50.0
45.0 280 C
40.0 290 C
35.0 300 C
Acetaldehyde (ppm)
30.0
y = 4.4006x - 34.489
2
25.0 R = 0.976
y = 1.1339x - 6.4286
2
R = 0.9597
20.0
y = 0.3763x + 0.6121
2
R = 0.9815
15.0
10.0
5.0
0.0
0 5 10 15 20
Time (minutes)
Figure C-11: AA generation plots for the 10,000 ppm alpha-cyclodextrin/ PET blend
sample
253
50.0
45.0 280 C
290 C
40.0
300 C
35.0
Acetaldehyde (ppm)
30.0
5.0
0.0
0 5 10 15 20
Time (minutes)
Figure C-12: AA generation plots for the 5000 ppm alpha-cyclodextrin/ PET blend
sample
70.0
60.0
280 C
290 C
50.0 300 C
Acetaldehyde (ppm)
40.0
y = 6.1812x - 42.849
2
R = 0.9893
30.0
y = 3.1481x - 22.382
2
R = 0.9306
20.0
y = 0.817x - 0.9064
2
R = 0.7758
10.0
0.0
0 5 10 15 20
Time (minutes)
Figure C-13: AA generation plots for the 1200 ppm alpha-cyclodextrin/ PET blend
sample
254
90.0
280 C
80.0
290 C
70.0
300 C
Acetaldehyde (ppm)
60.0
50.0
y = 7.2048x - 47.341
2
R = 0.9879
40.0
y = 3.9843x - 26.77
2
R = 0.9816
30.0
y = 1.3576x - 5.165
2
R = 0.9813
20.0
10.0
0.0
0 5 10 15 20
Time (minutes)
Figure C-14: AA generation plots for the 500 ppm alpha-cyclodextrin/ PET blend
sample
70.0
60.0 280 C
290 C
50.0
300 C
Acetaldehyde (ppm)
40.0
y = 5.166x - 27.374
2
R = 0.994
30.0
y = 2.2346x - 8.7653
2
R = 0.9927
20.0
y = 0.8797x + 2.4067
2
R = 0.8454
10.0
0.0
0 5 10 15 20
Time (minutes)
Figure C-15: AA generation plots for the 10,000 ppm MXDA/ PET blend sample
255
80.0
70.0
280 C
60.0 290 C
Acetaldehyde (ppm)
300 C
50.0
40.0
y = 5.0212x - 23.097
2
R = 0.9962
30.0
y = 2.4073x - 11.696
2
R = 0.9521
20.0
y = 1.3516x - 6.233
2
R = 0.9218
10.0
0.0
0 5 10 15 20
Time (minutes)
Figure C-16: AA generation plots for the 1200 ppm MXDA/ PET blend sample
70.0
60.0
280 C
50.0
290 C
Acetaldehyde (ppm)
300 C
40.0
y = 5.4201x - 28.709
2
R = 0.9986
30.0
y = 2.3245x - 8.1065
2
R = 0.9778
20.0
y = 1.5383x - 5.0164
2
R = 0.9529
10.0
0.0
0 5 10 15 20
Time (minutes)
Figure C-17: AA generation plots for the 500 ppm MXDA/ PET blend sample
256
70.0
280 C
60.0
290 C
50.0
300 C
Acetaldehyde (ppm)
y = 6.1134x - 37.74
2
R = 0.9928
40.0
y = 2.5574x - 10.064
2
R = 0.9954
30.0
y = 1.4682x - 4.2849
2
R =1
20.0
10.0
0.0
0 5 10 15 20
Time (minutes)
Figure C-18: AA generation plots for the 200 ppm MXDA/ PET blend sample
80.0
70.0 280 C
290 C
60.0
300 C
Acetaldehyde (ppm)
50.0
y = 6.8088x - 40.829
2
R = 0.9871
40.0
y = 4.6202x - 30.822
2
R = 0.938
30.0
y = 1.7549x - 5.0404
2
R = 0.9933
20.0
10.0
0.0
0 5 10 15 20
Time (minutes)
Figure C-19: AA generation plots for the 100 ppm MXDA/ PET blend sample
257
*The AA generation plots for the 1200 ppm anthranilamide/PET blend sample are shown
in Figure 4-23.
258
Appendix D
Arrhenius Plots
2.50
2.00
y = -25926x + 47.253
R2 = 0.9795
1.50
ln Rate
1.00
0.50
0.00
0.00174 0.00175 0.00176 0.00177 0.00178 0.00179 0.00180 0.00181 0.00182
1/Temperature (1/K)
Figure D-1: Arrhenius plot for the “one-time” processed PET sample
259
2.50
2.00
y = -23603x + 43.24
R2 = 0.9915
1.50
ln Rate
1.00
0.50
0.00
0.00174 0.00175 0.00176 0.00177 0.00178 0.00179 0.00180 0.00181 0.00182
1/Temperature (1/K)
Figure D-2: Arrhenius plot for the “two-times” processed PET sample
2.50
2.00
y = -19796x + 36.649
R2 = 0.961
1.50
ln Rate
1.00
0.50
0.00
0.00174 0.00175 0.00176 0.00177 0.00178 0.00179 0.00180 0.00181 0.00182
1/Temperature (1/K)
Figure D-3: Arrhenius plot for the “three-times” processed PET sample
260
1.00
0.50
y = -29401x + 51.988
R2 = 0.9969
0.00
ln Rate
-0.50
-1.00
-1.50
1/Temperature (1/K)
Figure D-4: Arrhenius plot for the 10,000 ppm anthranilamide/PET blend sample
1.20
1.00
0.80
y = -18593x + 33.577
R2 = 0.9865
0.60
ln Rate
0.40
0.20
0.00
0.00174 0.00175 0.00176 0.00177 0.00178 0.00179 0.00180 0.00181 0.00182
-0.20
1/Temperature (1/K)
Figure D-5: Arrhenius plot for the 1200 ppm anthranilamide/PET blend sample
261
2.00
1.80
1.60
1.00
0.80
0.60
0.40
0.20
0.00
0.00174 0.00175 0.00176 0.00177 0.00178 0.00179 0.00180 0.00181 0.00182
1/Temperature (1/K)
Figure D-6: Arrhenius plot for the 500 ppm anthranilamide/PET blend sample
2.50
2.00
1.50
y = -20631x + 38.032
ln Rate
R2 = 0.9559
1.00
0.50
0.00
0.00174 0.00175 0.00176 0.00177 0.00178 0.00179 0.00180 0.00181 0.00182
1/Temperature (1/K)
Figure D-7: Arrhenius plot for the 200 ppm anthranilamide/PET blend sample
262
2.50
2.00
y = -26518x + 48.332
R2 = 0.9902
1.50
ln Rate
1.00
0.50
0.00
0.00174 0.00175 0.00176 0.00177 0.00178 0.00179 0.00180 0.00181 0.00182
1/Temperature (1/K)
Figure D-8: Arrhenius plot for the 100 ppm anthranilamide/PET blend sample
1.50
1.00
y = -39310x + 69.649
R2 = 0.9939
0.50
0.00
ln Rate
-0.50
-1.00
-1.50
-2.00
1/Temperature (1/K)
Figure D-9: Arrhenius plot for the 50,000 ppm alpha-cyclodextrin/PET blend sample
263
1.50
1.00
y = -41738x + 74.034
R2 = 0.9816
0.50
0.00
ln Rate
-0.50
-1.00
-1.50
-2.00
1/Temperature (1/K)
Figure D-10: Arrhenius plot for the 25,000 ppm alpha-cyclodextrin/PET blend sample
2.00
1.50
1.00
y = -38954x + 69.396
R2 = 0.9952
0.50
ln Rate
0.00
0.00174 0.00175 0.00176 0.00177 0.00178 0.00179 0.00180 0.00181 0.00182
-0.50
-1.00
-1.50
1/Temperature (1/K)
Figure D-11: Arrhenius plot for the 10,000 ppm alpha-cyclodextrin/PET blend sample
264
2.00
1.50
y = -33837x + 60.536
R2 = 0.9896
1.00
ln Rate
0.50
0.00
0.00174 0.00175 0.00176 0.00177 0.00178 0.00179 0.00180 0.00181 0.00182
-0.50
-1.00
1/Temperature (1/K)
Figure D-12: Arrhenius plot for the 5000 ppm alpha-cyclodextrin/PET blend sample
2.50
2.00
y = -32138x + 58.003
R2 = 0.968
1.50
ln Rate
1.00
0.50
0.00
0.00174 0.00175 0.00176 0.00177 0.00178 0.00179 0.00180 0.00181 0.00182
-0.50
1/Temperature (1/K)
Figure D-13: Arrhenius plot for the 1200 ppm alpha-cyclodextrin/PET blend sample
265
2.50
2.00
y = -26500x + 48.287
R2 = 0.9759
1.50
ln Rate
1.00
0.50
0.00
0.00174 0.00175 0.00176 0.00177 0.00178 0.00179 0.00180 0.00181 0.00182
1/Temperature (1/K)
Figure D-14: Arrhenius plot for the 500 ppm alpha-cyclodextrin/PET blend sample
1.80
1.60
1.40
y = -20787x + 37.85
R2 = 0.9937
1.20
1.00
ln Rate
0.80
0.60
0.40
0.20
0.00
0.00174 0.00175 0.00176 0.00177 0.00178 0.00179 0.00180 0.00181 0.00182
1/Temperature (1/K)
Figure D-15: Arrhenius plot for the 1200 ppm MXDA/PET blend sample
266
1.80
1.60
1.40
y = -19922x + 36.371
R2 = 0.9579
1.20
1.00
ln Rate
0.80
0.60
0.40
0.20
0.00
0.00174 0.00175 0.00176 0.00177 0.00178 0.00179 0.00180 0.00181 0.00182
1/Temperature (1/K)
Figure D-16: Arrhenius plot for the 500 ppm MXDA/PET blend sample
2.00
1.80
1.60
y = -22580x + 41.148
1.40
R2 = 0.9812
1.20
ln Rate
1.00
0.80
0.60
0.40
0.20
0.00
0.00174 0.00175 0.00176 0.00177 0.00178 0.00179 0.00180 0.00181 0.00182
1/Temperature (1/K)
Figure D-17: Arrhenius plot for the 200 ppm MXDA/PET blend sample
267
2.50
2.00
y = -21544x + 39.602
R2 = 0.9471
1.50
ln Rate
1.00
0.50
0.00
0.00174 0.00175 0.00176 0.00177 0.00178 0.00179 0.00180 0.00181 0.00182
1/Temperature (1/K)
Figure D-18: Arrhenius plot for the 100 ppm MXDA/PET blend sample
*The Arrhenius plot for the virgin PET sample, Voridian CB12 PET resin, is shown in
Figure 4-32.
**The Arrhenius plot of the 10,000 ppm MXDA/PET blend sample is shown in Figure
4-27.
268
Appendix E
Table E.1: Residual AA data for the control PET pelletized samples
Number of Sample Peak Calibration AA Concentration
Processing Weight Area Factor (ppm)
Times (grams) Measured Average
0.31795 262.89 997.76 0.8
0
0.37230 309.34 997.76 0.8
0.8
0.36160 3440.53 997.76 9.5
1 0.33355 2810.13 997.76 8.4 9.0
0.36225 3222.81 997.76 8.9
0.42160 3548.47 607.32 13.9
2
0.29300 2339.18 607.32 13.1
13.5
0.32455 2787.06 607.32 14.1
3 0.34670 3014.77 607.32 14.3 14.5
0.37735 3442.92 607.32 15.0
Table E.2: Residual AA data for the anthranilamide/PET blend pelletized samples
AA Scavenger Sample Peak Calibration AA Concentration
Concentration Weight Area Factor (ppm)
(ppm) (grams) Measured Average
0.37050 382.29 997.76 1.0
1200 0.41515 418.46 997.76 1.0
1.0
0.30000 883.41 997.76 3.0
500 0.32855 943.95 997.76 2.9
2.9
0.31830 1121.57 997.76 3.5
200 0.32530 1101.01 997.76 3.4
3.5
0.31940 1759.95 997.76 5.5
100 0.30195 1467.89 997.76 4.9
5.2
*10,000 ppm anthranilamide/PET blend sample was crystallized prior to residual AA
analysis and was therefore not analyzed.
269
Table E.3: Residual AA data for the alpha-cyclodextrin/PET blend pelletized samples
AA Scavenger Sample Peak Calibration AA Concentration
Concentration Weight Area Factor (ppm)
(ppm) (grams) Measured Average
0.32105 850.28 997.76 2.7
50,000 0.33890 859.9 997.76 2.5
2.6
0.30835 771.16 997.76 2.5
25,000 0.32920 976.4 997.76 3.0
2.7
0.30890 825.7 997.76 2.7
10,000 0.29715 740.93 997.76 2.5
2.6
0.33785 1045.93 997.76 3.1
5000 0.32785 803.48 997.76 2.5
2.8
0.32540 1034.51 997.76 3.2
1200 0.31900 1059.25 997.76 3.3
3.3
0.29275 1456.23 997.76 5.0
500 0.31710 1539.92 997.76 4.9
4.9
Table E.4: Residual AA data for the MXDA/PET blend pelletized samples
AA Scavenger Sample Peak Calibration AA Concentration
Concentration Weight Area Factor (ppm)
(ppm) (grams) Measured Average
0.32840 810.54 997.76 2.5
10,000 0.29355 893.1 997.76 3.0
2.8
0.38100 1270.76 997.76 3.3
1200 0.30530 1069.07 997.76 3.5
3.4
0.30215 1136.53 997.76 3.8
500 0.30175 1031.58 997.76 3.4
3.6
0.35285 1122.09 997.76 3.2
200 0.33590 1092.64 997.76 3.3
3.2
0.29875 1398.91 997.76 4.7
100 0.33440 1174.02 997.76 3.5
4.1
Table E.5: Residual AA data for the PET control preform samples
Number Preform Sample Peak Calibration AA Concentration
of # Weight Area Factor (ppm)
Processing (grams) Measured Overall
Times Average
0.23540 2016.35 997.76 8.6
1 0.28975 2220.50 997.76 7.7
0.31690 2497.23 997.76 7.9
0.25230 2113.16 997.76 8.4
1 2 0.26200 2076.94 997.76 7.9
8.3
0.23540 2115.34 997.76 9.0
3 0.27660 2573.11 997.76 9.3
0.26920 2030.63 997.76 7.6
270
Table E.6: Residual AA data for the anthranilamide/PET preform samples
AA Scavenger Preform Sample Peak Calibration AA Concentration
Concentration # Weight Area Factor (ppm)
(ppm) (grams) Measured Overall
Average
0.31950 1329.36 997.76 4.2
1 0.32495 1208.60 997.76 3.7
0.32155 1117.58 997.76 3.5
0.28760 1068.99 997.76 3.7
200 2 0.30770 1143.28 997.76 3.7 3.7
0.30220 1173.87 997.76 3.9
0.27245 835.33 997.76 3.1
3 0.34575 1269.13 997.76 3.7
0.28550 1083.24 997.76 3.8
0.28610 1226.11 997.76 4.3
1 0.29265 1253.49 997.76 4.3
0.35085 1984.18 997.76 5.7
2
100 0.29525 1367.02 997.76 4.6 4.5
0.31510 1167.27 997.76 3.7
3 0.27695 1244.44 997.76 4.5
0.34720 1364.31 997.76 3.9
271
Table E.8: Residual AA data for the MXDA/PET preform samples
AA Scavenger Preform Sample Peak Calibration AA Concentration
Concentration # Weight Area Factor (ppm)
(ppm) (grams) Measured Overall
Average
0.27425 1599.40 997.76 5.8
1 0.31565 1619.12 997.76 5.1
0.32605 1664.68 997.76 5.1
0.36975 1391.97 997.76 3.8
200 2 0.30485 986.34 997.76 3.2 4.6
0.25450 793.49 997.76 3.1
0.34915 1905.83 997.76 5.5
3 0.29340 1172.77 997.76 4.0
0.34005 1992.79 997.76 5.9
0.33475 2207.49 997.76 6.6
1 0.25985 1241.14 997.76 4.8
0.28880 1226.73 997.76 4.3
2 0.29330 1018.32 997.76 3.5
100 0.31425 1982.32 997.76 6.3
5.3
0.32795 1902.30 997.76 5.8
3 0.29690 1170.65 997.76 4.0
0.25850 1673.71 997.76 6.5
272
Appendix F
Table F.1: Melt viscosity data for the control PET pelletized samples
Resin Number of η* (Paxseconds) @ I.V. (dL/g)
Processing Times 10 radians/second Calculated Average
853.900 0.80
1234.400 0.86
754.640 0.78
0 776.730 0.79
0.80
814.700 0.79
762.010 0.78
CB12 724.320 0.78
1 685.990 0.77
0.78
407.340 0.69
2 389.950 0.69
0.69
319.280 0.66
3 303.520 0.65
0.65
Table F.2: Melt viscosity data for the anthranilamide/PET blend pelletized samples
Resin AA Scavenger η* (Paxseconds) I.V. (dL/g)
Concentration @ 10
Calculated Average
(ppm) radians/second
125.570 0.52
10,000 148.680 0.55 0.51
88.662 0.47
324.320 0.66
1200 299.250 0.65
0.66
CB12 500
363.900 0.68
0.68
375.300 0.68
373.130 0.68
200 339.770 0.67
0.68
319.240 0.66
100 360.030 0.68
0.67
273
Table F.3: Melt viscosity data for the alpha-cyclodextrin/PET blend pelletized samples
Resin AA Scavenger η* (Paxseconds) I.V. (dL/g)
Concentration @ 10 Calculated Average
(ppm) radians/second
54.810 0.40
50,000 54.806 0.40
0.40
80.640 0.46
25,000 79.998 0.46
0.46
142.070 0.54
10,000 143.420 0.54
0.54
CB12 186.590 0.58
5000 186.380 0.58
0.58
463.270 0.71
1200 450.910 0.71
0.71
506.740 0.73
500 527.640 0.73
0.73
Table F.4: Melt viscosity data for the MXDA/PET blend pelletized samples
Resin AA Scavenger η* (Paxseconds) I.V. (dL/g)
Concentration @ 10 Calculated Average
(ppm) radians/second
35.708 0.33
10,000 37.114 0.34
0.34
360.350 0.68
1200 352.600 0.67
0.68
432.210 0.70
CB12 500 395.860 0.69
0.70
352.630 0.67
200 318.130 0.66
0.67
372.120 0.68
100 353.780 0.67
0.68
Table F.5: Melt viscosity data for the control PET preform samples
Resin Preform η* (Paxseconds) I.V. (dL/g)
# @ 10
radians/second Calculated Overall Average
660.740 0.76
1
618.040 0.75
628.370 0.76
CB12 2
641.580 0.76
0.76
668.130 0.77
3
719.220 0.78
274
Table F.6: Melt viscosity data for the anthranilamide/PET blend preform samples
Resin AA Scavenger Preform η* (Paxseconds) I.V. (dL/g)
Concentration # @ 10 Calculated Overall
(ppm) radians/second Average
729.520 0.78
1 688.350 0.77
727.550 0.78
200 2 734.040 0.78
0.78
871.040 0.80
3 715.910 0.78
CB12 689.730 0.77
1 698.670 0.77
768.700 0.79
100 2 763.020 0.78
0.78
889.980 0.81
3 724.990 0.78
Table F.7: Melt viscosity data for the alpha-cyclodextrin/PET blend preform samples
Resin AA Scavenger Preform η* (Paxseconds) I.V. (dL/g)
Concentration # @ 10 Calculated Overall
(ppm) radians/second Average
501.820 0.72
1 379.990 0.68
487.060 0.72
1200 2 394.790 0.69
0.70
475.970 0.72
3 388.100 0.69
CB12 521.390 0.73
1 532.320 0.73
547.480 0.74
500 2 526.190 0.73
0.73
538.930 0.73
3 496.260 0.72
275
Table F.8: Melt viscosity data for the MXDA/PET blend preform samples
Resin AA Scavenger Preform η* (Paxseconds) I.V. (dL/g)
Concentration # @ 10 Calculated Overall
(ppm) radians/second Average
632.750 0.76
1 574.410 0.74
627.680 0.76
200 2 672.820 0.77
0.76
704.760 0.77
3 634.310 0.76
CB12 818.820 0.80
1 560.270 0.74
741.200 0.78
100 2 604.420 0.75
0.77
979.010 0.82
3 633.530 0.76
276
Appendix G
Table G.1: Color data for the Voridian CB12 PET control samples
Number of Measured Average
Sample
Processing Y X% Z%
# L a b L a b
Times
1 75.0 -1.8 -2.4
0 2 74.4 -1.7 -2.2 74.8 -1.8 -2.3 56.0 55.2 58.4
3 75.0 -1.9 -2.3
1 68.5 -0.4 0.7
1 2 68.4 -0.4 0.7 68.5 -0.4 0.7 46.9 46.7 46.2
3 68.5 -0.3 0.7
1 71.5 -0.3 4.0
2 2 71.6 -0.5 3.9 71.5 -0.4 4.0 51.1 50.9 47.1
3 71.4 -0.4 4.0
1 71.1 -0.4 5.8
3 2 71.2 -0.4 5.6 71.2 -0.4 5.6 50.6 50.5 44.9
3 71.2 -0.5 5.5
277
Table G.2: Color data for the anthranilamide/PET blend samples
AA
Measured Average
Scavenger Sample
Y X% Z%
Concentr- # L a b L a b
ation (ppm)
1 67.0 -8.9 8.3
10,000 2 69.1 -8.9 8.1 68.5 -8.9 8.2 46.9 43.4 38.9
3 69.4 -8.8 8.3
1 72.5 -7.7 6.7
1200 2 72.1 -7.6 6.9 72.6 -7.6 6.8 52.7 49.6 45.7
3 73.2 -7.5 6.8
1 73.7 -7.2 7.4
500 2 73.9 -7.1 7.3 73.6 -7.2 7.4 54.2 51.1 46.4
3 73.2 -7.2 7.5
1 70.2 -10.3 2.9
200 2 69.9 -10.3 3.0 69.9 -10.3 3.0 48.8 44.7 45.9
3 69.5 -10.3 3.0
1 65.1 -10.1 2.6
100 2 66.3 -9.9 2.3 66.2 -10.0 2.4 43.8 40.0 41.5
3 67.1 -10.0 2.3
278
Table G.4: Color data for the alpha-cyclodextrin/PET blend samples
AA
Measured Average
Scavenger Sample
Y X% Z%
Concentr- # L a b L a b
ation (ppm)
1 53.2 -36.7 12.8
50,000 2 52.0 -37.1 12.7 52.4 -36.9 12.8 27.5 16.4 17.9
3 52.0 -37.0 12.8
1 43.4 -47.6 12.7
25,000 2 43.8 -47.3 12.7 43.5 -47.3 12.7 18.9 7.2 11.0
3 43.3 -47.1 12.7
1 43.6 -47.7 12.3
10,000 2 43.7 -47.5 12.4 43.7 -47.6 12.4 19.1 7.2 11.4
3 43.8 -47.6 12.4
1 41.8 -44.7 10.5
5000 2 41.7 -44.6 10.6 41.8 -44.7 10.5 17.5 6.8 11.2
3 41.9 -44.7 10.5
1 58.6 -22.8 11.8
1200 2 59.1 -22.3 11.9 58.5 -22.6 11.9 34.2 26.7 24.3
3 57.8 -22.7 11.9
1 63.9 -11.7 10.0
500 2 64.3 -11.9 10.2 64.2 -11.9 10.1 41.2 36.8 31.9
3 64.3 -11.9 10.1
*The b value was so greatly altered that the resulting yellowness indexes were false
values and therefore the data for the alpha-cyclodextrin/PET blend samples was not
included in the results and discussion of this work.
279
Appendix H
DT
ρ ×Cp = (∇ • q ) − (τ : ∇v ) (Equation 29)
Dt
ρ ×Cp
DT
( )
= k∇ T − (τ : ∇v )
2
(Equation 30)
Dt
DT ∂T ∂T vθ ∂T ∂T
where: = + vr + + vz (Equation 31)
Dt ∂t ∂r r ∂θ ∂z
∂ 2T 1 ∂T 1 ∂ 2T ∂ 2T
where: ( 2
)
k∇ T = k 2 + + 2 + 2 (Equation 32)
∂ r r ∂r r ∂θ 2
∂z
∂vr 1 ∂vr vθ ∂v
τ rr + τ rθ − + τ rz r
∂r r ∂θ r ∂z
∂v 1 ∂vθ vr ∂v
+ τ θr θ + τ θθ + + τ θz θ
where: (τ : ∇v ) = ∂r r ∂θ r ∂z (Equation 33)
∂v 1 ∂vz ∂v
+ τ zr z + τ zrθ + τ zz z
∂r r ∂θ ∂z
280
∂T ∂T 1 ∂ ∂T ∂v
ρ ×Cp + vz = k × r × + τ zr z (Equation 34)
∂t ∂z r ∂r ∂r ∂r
2
∂v ∂v ∂v ∂v
where: τ zr z = η z z = η z (Equation 35)
∂r ∂r ∂r ∂r
2
∂T ∂T 1 ∂ ∂T ∂v
ρ ×Cp + vz = k × r × + η z (Equation 36)
∂t ∂z r ∂r ∂r ∂r
2
∂T ∂T 1 ∂ ∂T ∂v
ρ ×Cp +v = k × r × + η (Equation 12)
∂t ∂z r ∂r ∂r ∂r
281
Table H.1: Definition of Terms Listed in Equations 12 and 29 to 36
Terms Meaning
ρ Density
Cp Heat capacity
T Temperature
t Time
∇ Gradient
q Heat generation
v Velocity
τ Shear stress
k Boltzmann’s constant
vr Velocity in the radial direction
vθ Velocity in the rotation direction
vz Velocity in the longitudinal direction
r Radial direction
θ Rotational direction
z Longitudinal direction
τrr Flux of radial momentum directed in the radial direction
τrθ Flux of rotational momentum directed in the radial direction
τrz Flux of longitudinal momentum directed in the radial direction
τθr Flux of radial momentum directed in the rotational direction
τθθ Flux rotational momentum directed in the rotational direction
τθz Flux of longitudinal momentum directed in the rotational direction
τzr Flux of radial momentum directed the longitudinal direction
τzθ Flux of rotational momentum directed in the longitudinal direction
τzz Flux of longitudinal momentum directed in the longitudinal direction
η Viscosity
282
Appendix I
283
Table I.2: AA Generation Data for the 10,000 ppm Anthranilamide/PET Blend
AA Scavenger AA Scavenger Temperature Time AA Average
Concentration (oC) (minutes) (ppm) AA
(ppm) (ppm)
5 1.4
1.0
5 0.6
10 3.0
2.6
10 2.2
15 8.9
8.6
15 8.3
20 12.1
11.3
20 10.5
25 13.5
10.4
25 7.3
30 16.4
16.6
Anthranilamide 10,000 30 16.8
290
35 22.9
20.4
35 17.8
40 19.3
20.9
40 22.5
45 22.0
23.8
45 25.6
50 28.8
22.5
50 16.2
55 22.2
23.6
55 24.9
60 20.9
22.2
60 23.4
284
Table I.3: AA Generation Data for the 10,000 ppm Alpha-Cyclodextrin/PET Blend
AA Scavenger AA Scavenger Temperature Time AA Average
Concentration (oC) (minutes) (ppm) AA
(ppm) (ppm)
5 1.4
1.2
5 1.0
10 5.2
4.6
10 3.9
15 9.6
9.0
15 8.3
20 16.8
17.0
20 17.2
25 21.2
20.5
25 19.8
30 24.9
Alpha- 26.0
10,000 30 27.0
Cyclodextrin 290
35 30.4
29.2
35 28.1
40 33.5
34.4
40 35.2
45 38.6
36.5
45 34.4
50 41.2
41.7
50 42.2
55 39.0
42.8
55 46.6
60 42.4
43.4
60 44.4
285
Table I.4: AA Generation Data for the 10,000 ppm MXDA/PET Blend
AA Scavenger AA Scavenger Temperature Time AA Average
Concentration (oC) (minutes) (ppm) AA
(ppm) (ppm)
5 3.2
3.5
5 3.8
10 12.5
9.6
10 6.8
15 24.7
23.8
15 22.8
20 34.7
36.6
20 38.5
25 39.8
45.9
25 52.1
30 54.0
53.9
MXDA 10,000 30 53.7
290
35 62.2
64.9
35 67.5
40 71.7
70.4
40 69.1
45 78.8
75.8
45 72.9
50 74.4
78.3
50 82.3
55 84.6
85.5
55 86.4
60 91.7
88.1
60 84.5
286
Appendix J
Table J.1: Calculated Data Based on 60 Minute AA Generation Data, at 290oC, for the
10,000 ppm Anthranilamide/PET Blend
Time Average d[AA]/dt RG – ln (RG – ln ([AA])
(minutes) AA (ppm) (d[AA]/dt) (d[AA]/dt))
5 1.0 0.89 2.0 0.72 0.00
10 2.6 0.81 2.1 0.76 0.95
15 8.6 0.73 2.2 0.80 2.15
20 11.3 0.64 2.3 0.83 2.42
25 10.4 0.56 2.4 0.87 2.34
30 16.6 0.47 2.5 0.90 2.81
35 20.4 0.39 2.6 0.94 3.01
40 20.9 0.31 2.6 0.97 3.04
45 23.8 0.22 2.7 1.00 3.17
50 22.5 0.14 2.8 1.03 3.11
55 23.6 0.05 2.9 1.06 3.16
60 22.2 -0.03 3.0 1.09 3.10
287
Table J.2: Calculated Data Based on 60 Minute AA Generation Data, at 290oC, for the
10,000 ppm Alpha-Cyclodextrin/PET Blend
Time Average d[AA]/dt RG – ln (RG – ln ([AA])
(minutes) AA (ppm) (d[AA]/dt) (d[AA]/dt))
5 1.2 1.23 1.7 0.53 0.19
10 4.6 1.16 1.8 0.58 1.52
15 9.0 1.09 1.9 0.62 2.19
20 17.0 1.01 1.9 0.66 2.83
25 20.5 0.94 2.0 0.69 3.02
30 26.0 0.86 2.1 0.73 3.26
35 29.2 0.79 2.2 0.77 3.38
40 34.4 0.72 2.2 0.80 3.54
45 36.5 0.64 2.3 0.83 3.60
50 41.7 0.57 2.4 0.86 3.73
55 42.8 0.49 2.4 0.89 3.76
60 43.4 0.42 2.5 0.92 3.77
* The natural log of a value less than or equal to zero does not produce a real number
Table J.3: Calculated Data Based on 60 Minute AA Generation Data, at 290oC, for the
10,000 ppm MXDA/PET Blend
Time Average d[AA]/dt RG – ln (RG – ln ([AA])
(minutes) AA (ppm) (d[AA]/dt) (d[AA]/dt))
5 3.5 2.65 0.3 -1.22 1.26
10 9.6 2.45 0.5 -0.72 2.26
15 23.8 2.26 0.7 -0.39 3.17
20 36.6 2.07 0.9 -0.14 3.60
25 45.9 1.88 1.1 0.06 3.83
30 53.9 1.69 1.3 0.23 3.99
35 64.9 1.49 1.4 0.37 4.17
40 70.4 1.30 1.6 0.49 4.25
45 75.8 1.11 1.8 0.60 4.33
50 78.3 0.92 2.0 0.70 4.36
55 85.5 0.73 2.2 0.79 4.45
60 88.1 0.53 2.4 0.88 4.48
288
Table K.1: Anthranilamide/PET Blend Data, at 280oC, Calculated for the Original ln(k2)
Versus ln([S0]) Plot
Average Appendix K
Average [AA]a
[S0] Time a [AA]a Calculated ln
[AA] for Each ln (k2)
(ppm) (min.) Value (ppm) k2 [S0]
(ppm) [S0]
(ppm)
9 6.9 1.2
100 13 10.7 1.3 1.3 0.1225 -2.0995 4.6
17 18.2 1.4
9 6.6 1.2
200 13 13.9 1.3 1.3 -0.2731 * 5.3
17 22.0 1.4
289
9 11.0 1.3
500 13 15.7 0.1052 1.3 1.3 0.1189 -2.1294 6.2
Data Used to Determine the k1, bb1, bb2, and b Values
17 22.4 1.4
9 8.5 1.3
1200 13 10.6 1.3 1.3 0.4292 -0.8458 7.1
17 16.6 1.3
9 3.7 1.1
10,000 13 5.4 1.2 1.2 1.0753 0.0726 9.2
17 6.1 1.2
* The natural log of a value less than or equal to zero does not produce a real number
Table K.2: Anthranilamide/PET Blend Data, at 290oC, Calculated for the Original ln(k2) Versus ln([S0])
Plot
9 11.3 1.3
100 13 21.6 1.4 1.4 -0.6312 * 4.6
17 41.8 1.5
9 8.0 1.2
200 13 27.7 1.4 1.4 -1.3058 * 5.3
17 46.0 1.5
9 11.3 1.3
500 13 22.4 0.1052 1.4 1.4 0.2365 -1.4419 6.2
290
17 32.2 1.4
9 12.1 1.3
1200 13 18.5 1.4 1.4 0.7690 -0.2627 7.1
17 27.3 1.4
9 4.1 1.2
10,000 13 5.7 1.2 1.2 1.6965 0.5286 9.2
17 10.9 1.3
* The natural log of a value less than or equal to zero does not produce a real number
Table K.3: Anthranilamide/PET Blend Data, at 300oC, Calculated for the Original ln(k2) Versus ln([S0])
Plot
9 18.8 1.4
100 13 51.3 1.5 1.5 0.2969 -1.2144 4.6
17 78.8 1.6
9 18.1 1.4
200 13 46.8 1.5 1.5 0.6154 -0.4855 5.3
17 74.5 1.6
9 22.3 1.4
500 13 42.9 0.1052 1.5 1.5 1.3405 0.2930 6.2
291
17 70.3 1.6
9 17.1 1.3
1200 13 27.1 1.4 1.4 3.5627 1.2705 7.1
17 41.1 1.5
9 6.2 1.2
10,000 13 14.5 1.3 1.3 4.6350 1.5336 9.2
17 21.7 1.4
Table K.4: Alpha-Cyclodextrin/PET Blend Data, at 280oC, Calculated for the Original ln(k2) Versus
ln([S0]) Plot
292
17 6.7 1.2
0.1042
9 4.1 1.2
10,000 13 5.3 1.2 1.2 1.0007 0.0007 9.2
17 7.1 1.2
9 3.9 1.2
25,000 13 5.3 1.2 1.2 1.1039 0.0989 10.1
17 6.1 1.2
9 4.7 1.2
50,000 13 5.8 1.2 1.2 1.0936 0.0894 10.8
17 6.8 1.2
Table K.5: Alpha-Cyclodextrin/PET Blend Data, at 290oC, Calculated for the Original ln(k2) Versus
ln([S0]) Plot
293
17 20.0 1.4
0.1042
9 4.3 1.2
10,000 13 7.2 1.2 1.2 1.4637 0.3810 9.2
17 13.4 1.3
9 5.9 1.2
25,000 13 7.8 1.2 1.2 1.7605 0.5656 10.1
17 11.9 1.3
9 6.5 1.2
50,000 13 8.7 1.3 1.3 1.7303 0.5483 10.8
17 12.7 1.3
* The natural log of a value less than or equal to zero does not produce a real number
Table K.6: Alpha-Cyclodextrin/PET Blend Data, at 300oC, Calculated for the Original ln(k2) Versus
ln([S0]) Plot
294
17 43.3 1.5
0.1042
9 6.7 1.2
10,000 13 19.5 1.4 1.4 2.7272 1.0033 9.2
17 41.9 1.5
9 7.7 1.2
25,000 13 18.4 1.4 1.4 3.1425 1.1450 10.1
17 37.6 1.5
9 11.4 1.3
50,000 13 19.8 1.4 1.4 3.5927 1.2789 10.8
17 35.9 1.5
Table K.7: MXDA/PET Blend Data, at 280oC, Calculated for the Original ln(k2) Versus ln([S0]) Plot
9 10.4 4.4
100 13 18.4 6.3 6.1 -0.0306 * 4.6
17 24.5 7.6
9 8.9 4.0
200 13 14.8 5.5 5.4 0.0185 -3.9876 5.3
17 20.7 6.8
9 9.6 4.2
500 13 13.4 0.6324 5.2 5.5 0.0113 -4.4850 6.2
295
17 21.9 7.0
9 5.0 2.8
1200 13 13.2 5.1 4.5 0.0479 -3.0393 7.1
17 15.8 5.7
9 9.5 4.1
10,000 13 15.6 5.7 5.2 0.1316 -2.0277 9.2
17 16.5 5.9
* The natural log of a value less than or equal to zero does not produce a real number
Table K.8: MXDA/PET Blend Data, at 290oC, Calculated for the Original ln(k2) Versus ln([S0]) Plot
9 13.5 5.2
100 13 23.8 7.4 8.2 -0.2053 * 4.6
17 50.5 11.9
9 12.6 5.0
200 13 24.0 7.5 7.2 0.0534 -2.9295 5.3
17 33.3 9.1
9 12.0 4.8
500 13 23.7 0.6324 7.4 7.0 0.0846 -2.4697 6.2
296
17 30.6 8.7
9 11.2 4.6
1200 13 17.1 6.0 6.4 0.0829 -2.4900 7.1
17 30.5 8.7
9 10.9 4.5
10,000 13 21.2 6.9 6.6 0.1071 -2.2343 9.2
17 28.8 8.4
* The natural log of a value less than or equal to zero does not produce a real number
Table K.9: MXDA/PET Blend Data, at 300oC, Calculated for the Original ln(k2) Versus ln([S0]) Plot
9 18.7 6.4
100 13 51.3 12.1 11.2 0.1049 -2.2544 4.6
17 73.1 15.1
9 18.5 6.3
200 13 39.3 10.2 10.3 0.1816 -1.7061 5.3
17 67.4 14.3
9 20.5 6.8
500 13 40.8 0.6324 10.4 10.4 0.2484 -1.3925 6.2
297
17 63.9 13.9
9 22.8 7.2
1200 13 40.8 10.4 10.5 0.2829 -1.2627 7.1
17 63.0 13.7
9 20.0 6.7
10,000 13 37.9 10.0 10.0 0.2865 -1.2499 9.2
17 61.4 13.5
* The natural log of a value less than or equal to zero does not produce a real number
Table K.10: Multiple Linear Regression Data Used to Determine the b, bb1, and bb2
Values for the Anthranilamide/PET Blends
ln (k2) ln ([S0]) Temperature Temperature 1/Temperature
(oC) (oK) (1/oK)
0.0726 9.21
-0.8458 7.09
280 553.15 0.001808
-2.1294 6.21
-2.0995 4.61
0.5286 9.21
-0.2627 7.09 290 563.15 0.001776
-1.4419 6.21
1.5336 9.21
1.2705 7.09
0.2930 6.21 300 573.15 0.001745
-0.4855 5.30
-1.2144 4.61
Table K.11: Multiple Linear Regression Data Used to Determine the b, bb1, and bb2
Values for the Alpha-Cyclodextrin/PET Blends
ln (k2) ln ([S0]) Temperature Temperature 1/Temperature
(oC) (oK) (1/oK)
0.0894 10.82
0.0989 10.13
0.0007 9.21
280 553.15 0.001808
-0.0883 8.52
-0.4468 7.09
-1.8111 6.21
0.5483 10.82
0.5656 10.13
290 563.15 0.001776
0.3810 9.21
-0.1024 8.52
1.2789 10.82
1.1450 10.13
1.0033 9.21
300 573.15 0.001745
1.0128 8.52
0.2261 7.09
-0.6389 6.21
298
Table K.12: Multiple Linear Regression Data Used to Determine the b, bb1, and bb2
Values for the MXDA/PET Blends
ln (k2) ln ([S0]) Temperature Temperature 1/Temperature
(oC) (oK) (1/oK)
-2.0277 9.21
-3.0393 7.09
280 553.15 0.001808
-4.4850 6.21
-3.9876 5.30
-2.2343 9.21
-2.4900 7.09
290 563.15 0.001776
-2.4697 6.21
-2.9295 5.30
-1.2499 9.21
-1.2627 7.09
-1.3925 6.21 300 573.15 0.001745
-1.7061 5.30
-2.2544 4.61
299
Table L.1: Predicted AA Generation Results for a 24 Cavity Injection Molding Process,
Modeled at 280oC
AA [AA]G – Appendix L
Scavenger AA in Cavities (ppm) Æ
Sample / AA (ppm) [AA]Initial
Concen- [AA]G
Scavenger (ppm)
tration
(ppm) 1 2 3 4 Avg. Max Avg. Max
CB12 PET 0 1.822 1.822 1.887 1.919 1.863 1.919 0.363 0.419
Anthranilamide 500 1.781 1.781 1.836 1.864 1.816 1.864 0.316 0.364
1200 1.758 1.758 1.808 1.833 1.789 1.833 0.289 0.333
10,000 1.634 1.634 1.657 1.669 1.649 1.669 0.149 0.169
300
500 1.752 1.752 1.799 1.823 1.782 1.823 0.282 0.323
1200 1.720 1.720 1.762 1.782 1.746 1.782 0.246 0.282
Alpha- 5000 1.654 1.654 1.682 1.696 1.672 1.696 0.172 0.196
Cyclodextrin 10,000 1.624 1.624 1.643 1.652 1.636 1.652 0.136 0.152
25,000 1.596 1.596 1.607 1.617 1.604 1.617 0.104 0.117
50,000 1.579 1.579 1.588 1.606 1.588 1.606 0.088 0.106
100 1.822 1.822 1.886 1.918 1.862 1.918 0.362 0.418
200 1.821 1.821 1.885 1.917 1.861 1.917 0.361 0.417
MXDA 500 1.820 1.820 1.885 1.917 1.861 1.917 0.361 0.417
1200 1.820 1.820 1.884 1.916 1.860 1.916 0.360 0.416
10,000 1.818 1.818 1.882 1.914 1.858 1.914 0.358 0.414
[AA]Initial (AA from Resin and Extruder) = 1.5 ppm, Each Cavity Represents a Set of 4 Symmetric Cavities
Table L.2: Predicted AA Generation Results for a 24 Cavity Injection Molding Process, Modeled at 280oC
[AA]G –
AA Scavenger AA in Cavities (ppm) Æ [AA]G AA (ppm) [AA]Initial
Sample /
Concentration (ppm)
Scavenger
(ppm)
1 2 3 4 5 6 Avg. Max Avg. Max
CB12 PET 0 1.850 1.850 1.821 1.821 1.966 1.966 1.879 1.966 0.379 0.466
100 1.831 1.831 1.804 1.804 1.941 1.941 1.859 1.941 0.359 0.441
200 1.823 1.823 1.797 1.797 1.930 1.930 1.850 1.930 0.350 0.430
Anthranilamide 500 1.807 1.807 1.783 1.783 1.908 1.908 1.833 1.908 0.333 0.408
1200 1.784 1.784 1.762 1.762 1.875 1.875 1.807 1.875 0.307 0.375
10,000 1.674 1.674 1.663 1.663 1.716 1.716 1.684 1.716 0.184 0.216
301
500 1.773 1.773 1.751 1.751 1.859 1.859 1.794 1.859 0.294 0.359
1200 1.746 1.746 1.727 1.727 1.822 1.822 1.765 1.822 0.265 0.322
Alpha- 5000 1.686 1.686 1.674 1.674 1.737 1.737 1.699 1.737 0.199 0.237
Cyclodextrin 10,000 1.645 1.645 1.637 1.637 1.680 1.680 1.654 1.680 0.154 0.180
25,000 1.612 1.612 1.603 1.603 1.641 1.641 1.619 1.641 0.119 0.141
50,000 1.597 1.597 1.590 1.590 1.620 1.620 1.602 1.620 0.102 0.120
100 1.849 1.849 1.820 1.820 1.965 1.965 1.878 1.965 0.378 0.465
200 1.849 1.849 1.820 1.820 1.965 1.965 1.878 1.965 0.378 0.465
MXDA 500 1.848 1.848 1.820 1.820 1.965 1.965 1.878 1.965 0.378 0.465
1200 1.848 1.848 1.820 1.820 1.964 1.964 1.877 1.964 0.377 0.464
10,000 1.847 1.847 1.819 1.819 1.963 1.963 1.876 1.963 0.376 0.463
[AA]Initial (AA from Resin and Extruder) = 1.5 ppm, Each Cavity Represents a Set of 4 Symmetric Cavities
Table L.3: Predicted AA Generation Results for a 32 Cavity Injection Molding Process, Modeled at 280oC
AA [AA]G –
Scavenger AA in Cavities (ppm) Æ [AA]G AA (ppm) [AA]Initial
Sample /
Concen- (ppm)
Scavenger
tration
(ppm) 1 2 3 4 5 6 7 8 Avg. Max Avg. Max
CB12 PET 0 1.848 1.848 1.884 1.884 1.812 1.812 1.848 1.848 1.848 1.884 0.348 0.384
100 1.829 1.829 1.863 1.863 1.796 1.796 1.829 1.829 1.829 1.863 0.329 0.363
200 1.822 1.822 1.854 1.854 1.789 1.789 1.822 1.822 1.822 1.854 0.322 0.354
Anthranilamide 500 1.806 1.806 1.836 1.836 1.775 1.775 1.806 1.806 1.806 1.836 0.306 0.336
1200 1.782 1.782 1.810 1.810 1.754 1.754 1.782 1.782 1.782 1.810 0.282 0.310
10,000 1.659 1.659 1.672 1.672 1.646 1.646 1.659 1.659 1.659 1.672 0.159 0.172
302
500 1.771 1.771 1.797 1.797 1.744 1.744 1.771 1.771 1.771 1.797 0.271 0.297
1200 1.744 1.744 1.767 1.767 1.721 1.721 1.744 1.744 1.744 1.767 0.244 0.267
Alpha- 5000 1.679 1.679 1.695 1.695 1.664 1.664 1.679 1.679 1.679 1.695 0.179 0.195
Cyclodextrin 10,000 1.638 1.638 1.648 1.648 1.627 1.627 1.638 1.638 1.638 1.648 0.138 0.148
25,000 1.609 1.609 1.620 1.620 1.602 1.602 1.609 1.609 1.610 1.620 0.110 0.120
50,000 1.595 1.595 1.609 1.609 1.589 1.589 1.595 1.595 1.597 1.609 0.097 0.109
100 1.847 1.847 1.883 1.883 1.811 1.811 1.847 1.847 1.847 1.883 0.347 0.383
200 1.847 1.847 1.882 1.882 1.811 1.811 1.847 1.847 1.847 1.882 0.347 0.382
MXDA 500 1.847 1.847 1.882 1.882 1.811 1.811 1.847 1.847 1.847 1.882 0.347 0.382
1200 1.846 1.846 1.882 1.882 1.811 1.811 1.846 1.846 1.846 1.882 0.346 0.382
10,000 1.845 1.845 1.881 1.881 1.810 1.810 1.845 1.845 1.845 1.881 0.345 0.381
[AA]Initial (AA from Resin and Extruder) = 1.5 ppm, Each Cavity Represents a Set of 4 Symmetric Cavities
Table L.4: Predicted AA Generation Results for a 48 Cavity Injection Molding Process, Modeled at 280oC
[AA]G –
AA Scavenger AA in Cavities (ppm) Æ [AA]G AA (ppm) [AA]Initial
Sample /
Concentration (ppm)
Scavenger
(ppm)
1 2 3 4 5 6 7 8 9 10 11 12 Avg. Max Avg. Max
CB12 PET 0 1.880 1.880 1.824 1.824 1.960 1.960 1.880 1.880 1.824 1.824 1.907 1.907 1.879 1.960 0.379 0.460
100 1.860 1.860 1.807 1.807 1.935 1.935 1.860 1.860 1.807 1.807 1.885 1.885 1.859 1.935 0.359 0.435
200 1.851 1.851 1.800 1.800 1.924 1.924 1.851 1.851 1.800 1.800 1.876 1.876 1.850 1.924 0.350 0.424
Anthranil- 1.834 1.834 1.786 1.786 1.902 1.902 1.834 1.834 1.786 1.786 1.857 1.857 1.833 1.902 0.333 0.402
500
amide
1200 1.808 1.808 1.764 1.764 1.870 1.870 1.808 1.808 1.764 1.764 1.828 1.828 1.807 1.870 0.307 0.370
10,000 1.674 1.674 1.653 1.653 1.703 1.703 1.674 1.674 1.653 1.653 1.684 1.684 1.674 1.703 0.174 0.203
303
500 1.795 1.795 1.753 1.753 1.854 1.854 1.795 1.795 1.753 1.753 1.815 1.815 1.794 1.854 0.294 0.354
1200 1.765 1.765 1.729 1.729 1.817 1.817 1.765 1.765 1.729 1.729 1.782 1.782 1.765 1.817 0.265 0.317
5000 1.695 1.695 1.670 1.670 1.729 1.729 1.695 1.695 1.670 1.670 1.706 1.706 1.694 1.729 0.194 0.229
Alpha-
Cyclodextrin 10,000 1.650 1.650 1.633 1.633 1.673 1.673 1.650 1.650 1.633 1.633 1.658 1.658 1.650 1.673 0.150 0.173
25,000 1.617 1.617 1.606 1.606 1.646 1.646 1.617 1.617 1.606 1.606 1.621 1.621 1.619 1.646 0.119 0.146
50,000 1.596 1.596 1.588 1.588 1.627 1.627 1.596 1.596 1.588 1.588 1.592 1.592 1.598 1.627 0.098 0.127
100 1.880 1.880 1.823 1.823 1.959 1.959 1.880 1.880 1.823 1.823 1.906 1.906 1.879 1.959 0.379 0.459
200 1.879 1.879 1.823 1.823 1.959 1.959 1.879 1.879 1.823 1.823 1.906 1.906 1.878 1.959 0.378 0.459
MXDA 500 1.879 1.879 1.823 1.823 1.959 1.959 1.879 1.879 1.823 1.823 1.906 1.906 1.878 1.959 0.378 0.459
1200 1.879 1.879 1.823 1.823 1.958 1.958 1.879 1.879 1.823 1.823 1.905 1.905 1.878 1.958 0.378 0.458
10,000 1.878 1.878 1.822 1.822 1.957 1.957 1.878 1.878 1.822 1.822 1.904 1.904 1.877 1.957 0.377 0.457
[AA]Initial (AA from Resin and Extruder) = 1.5 ppm, Each Cavity Represents a Set of 4 Symmetric Cavities
Table L.5: Predicted AA Generation Results for a 48 Cavity Injection Molding Process, Modeled at 270oC
[AA]G –
AA Scavenger AA in Cavities (ppm) Æ [AA]G AA (ppm) [AA]Initial
Sample /
Concentration (ppm)
Scavenger
(ppm)
1 2 3 4 5 6 7 8 9 10 11 12 Avg. Max Avg. Max
CB12 PET 0 1.639 1.639 1.618 1.618 1.668 1.668 1.639 1.639 1.618 1.618 1.649 1.649 1.639 1.668 0.139 0.168
100 1.631 1.631 1.611 1.611 1.658 1.658 1.631 1.631 1.611 1.611 1.640 1.640 1.630 1.658 0.130 0.158
200 1.627 1.627 1.608 1.608 1.653 1.653 1.627 1.627 1.608 1.608 1.636 1.636 1.627 1.653 0.127 0.153
Anthranil- 1.620 1.620 1.602 1.602 1.644 1.644 1.620 1.620 1.602 1.602 1.628 1.628 1.619 1.644 0.119 0.144
500
amide
1200 1.609 1.609 1.593 1.593 1.631 1.631 1.609 1.609 1.593 1.593 1.616 1.616 1.609 1.631 0.109 0.131
10,000 1.554 1.554 1.547 1.547 1.563 1.563 1.554 1.554 1.547 1.547 1.557 1.557 1.554 1.563 0.054 0.063
304
500 1.591 1.591 1.578 1.578 1.608 1.608 1.591 1.591 1.578 1.578 1.597 1.597 1.591 1.608 0.090 0.108
1200 1.574 1.574 1.564 1.564 1.588 1.588 1.574 1.574 1.564 1.564 1.579 1.579 1.574 1.588 0.074 0.088
5000 1.536 1.536 1.531 1.531 1.541 1.541 1.536 1.536 1.531 1.531 1.537 1.537 1.535 1.541 0.035 0.041
Alpha-
Cyclodextrin 10,000 1.514 1.514 1.513 1.513 1.515 1.515 1.514 1.514 1.513 1.513 1.514 1.514 1.514 1.515 0.014 0.015
25,000 1.509 1.509 1.508 1.508 1.510 1.510 1.509 1.509 1.508 1.508 1.509 1.509 1.509 1.510 0.009 0.010
50,000 1.507 1.507 1.506 1.506 1.508 1.508 1.507 1.507 1.506 1.506 1.507 1.507 1.507 1.508 0.007 0.008
100 1.639 1.639 1.618 1.618 1.668 1.668 1.639 1.639 1.618 1.618 1.649 1.649 1.639 1.668 0.139 0.168
200 1.639 1.639 1.618 1.618 1.668 1.668 1.639 1.639 1.618 1.618 1.649 1.649 1.639 1.668 0.139 0.168
MXDA 500 1.639 1.639 1.618 1.618 1.668 1.668 1.639 1.639 1.618 1.618 1.649 1.649 1.639 1.668 0.139 0.168
1200 1.639 1.639 1.618 1.618 1.668 1.668 1.639 1.639 1.618 1.618 1.649 1.649 1.639 1.668 0.139 0.168
10,000 1.639 1.639 1.618 1.618 1.667 1.667 1.639 1.639 1.618 1.618 1.648 1.648 1.638 1.667 0.138 0.167
[AA]Initial (AA from Resin and Extruder) = 1.5 ppm, Each Cavity Represents a Set of 4 Symmetric Cavities
Table L.6: Predicted AA Generation Results for a 48 Cavity Injection Molding Process, Modeled at 290oC
[AA]G –
AA Scavenger AA in Cavities (ppm) Æ [AA]G AA (ppm) [AA]Initial
Sample /
Concentration (ppm)
Scavenger
(ppm)
1 2 3 4 5 6 7 8 9 10 11 12 Avg. Max Avg. Max
CB12 PET 0 2.537 2.537 2.387 2.387 2.756 2.756 2.537 2.537 2.387 2.387 2.610 2.610 2.536 2.756 1.036 1.256
100 2.489 2.489 2.348 2.348 2.695 2.695 2.489 2.489 2.348 2.348 2.558 2.558 2.488 2.695 0.988 1.195
200 2.469 2.469 2.331 2.331 2.670 2.670 2.469 2.469 2.331 2.331 2.536 2.536 2.468 2.670 0.968 1.170
Anthranil- 2.428 2.428 2.297 2.297 2.618 2.618 2.428 2.428 2.297 2.297 2.491 2.491 2.427 2.618 0.927 1.118
500
amide
1200 2.367 2.367 2.247 2.247 2.541 2.541 2.367 2.367 2.247 2.247 2.425 2.425 2.366 2.541 0.866 1.041
10,000 2.058 2.058 1.996 1.996 2.148 2.148 2.058 2.058 1.996 1.996 2.088 2.088 2.057 2.148 0.557 0.648
305
500 2.393 2.393 2.269 2.269 2.574 2.574 2.393 2.393 2.269 2.269 2.454 2.454 2.392 2.574 0.892 1.074
1200 2.344 2.344 2.229 2.229 2.511 2.511 2.344 2.344 2.229 2.229 2.400 2.400 2.343 2.511 0.843 1.011
5000 2.201 2.201 2.109 2.109 2.336 2.336 2.201 2.201 2.109 2.109 2.246 2.246 2.200 2.336 0.700 0.836
Alpha-
Cyclodextrin 10,000 2.111 2.111 2.034 2.034 2.224 2.224 2.111 2.111 2.034 2.034 2.149 2.149 2.111 2.224 0.611 0.724
25,000 2.038 2.038 1.977 1.977 2.136 2.136 2.038 2.038 1.977 1.977 2.070 2.070 2.039 2.136 0.539 0.636
50,000 1.979 1.979 1.956 1.956 2.094 2.094 1.979 1.979 1.956 1.956 2.010 2.010 1.996 2.094 0.496 0.594
100 2.533 2.533 2.384 2.384 2.751 2.751 2.533 2.533 2.384 2.384 2.606 2.606 2.532 2.751 1.032 1.251
200 2.533 2.533 2.383 2.383 2.750 2.750 2.533 2.533 2.383 2.383 2.605 2.605 2.531 2.750 1.031 1.250
MXDA 500 2.532 2.532 2.383 2.383 2.749 2.749 2.532 2.532 2.383 2.383 2.604 2.604 2.531 2.749 1.031 1.249
1200 2.530 2.530 2.382 2.382 2.747 2.747 2.530 2.530 2.382 2.382 2.603 2.603 2.529 2.747 1.029 1.247
10,000 2.526 2.526 2.378 2.378 2.742 2.742 2.526 2.526 2.378 2.378 2.598 2.598 2.525 2.742 1.025 1.242
[AA]Initial (AA from Resin and Extruder) = 1.5 ppm, Each Cavity Represents a Set of 4 Symmetric Cavities
Table L.7: Predicted AA Generation Results for a 48 Cavity Injection Molding Process, Modeled at 300oC
[AA]G –
AA Scavenger AA in Cavities (ppm) Æ [AA]G AA (ppm) [AA]Initial
Sample /
Concentration (ppm)
Scavenger
(ppm)
1 2 3 4 5 6 7 8 9 10 11 12 Avg. Max Avg. Max
CB12 PET 0 4.282 4.282 3.887 3.887 4.868 4.868 4.282 4.282 3.887 3.887 4.477 4.477 4.281 4.868 2.781 3.368
100 4.162 4.162 3.788 3.788 4.718 4.718 4.162 4.162 3.788 3.788 4.347 4.347 4.161 4.718 2.661 3.218
200 4.110 4.110 3.746 3.746 4.653 4.653 4.110 4.110 3.746 3.746 4.291 4.291 4.109 4.653 2.609 3.153
Anthranil- 4.007 4.007 3.661 3.661 4.523 4.523 4.007 4.007 3.661 3.661 4.180 4.180 4.007 4.523 2.507 3.023
500
amide
1200 3.852 3.852 3.533 3.533 4.329 4.329 3.852 3.852 3.533 3.533 4.011 4.011 3.852 4.329 2.352 2.829
10,000 3.037 3.037 2.857 2.857 3.305 3.305 3.037 3.037 2.857 2.857 3.127 3.127 3.037 3.305 1.537 1.805
306
500 4.017 4.017 3.669 3.669 4.536 4.536 4.017 4.017 3.669 3.669 4.190 4.190 4.016 4.536 2.516 3.036
1200 3.922 3.922 3.590 3.590 4.416 4.416 3.922 3.922 3.590 3.590 4.087 4.087 3.921 4.416 2.421 2.916
5000 3.692 3.692 3.401 3.401 4.128 4.128 3.692 3.692 3.401 3.401 3.838 3.838 3.692 4.128 2.192 2.628
Alpha-
Cyclodextrin 10,000 3.536 3.536 3.272 3.272 3.930 3.930 3.536 3.536 3.272 3.272 3.667 3.667 3.536 3.930 2.036 2.430
25,000 3.411 3.411 3.179 3.179 3.782 3.782 3.411 3.411 3.179 3.179 3.518 3.518 3.413 3.782 1.913 2.282
50,000 3.319 3.319 3.121 3.121 3.691 3.691 3.319 3.319 3.121 3.121 3.472 3.472 3.341 3.691 1.841 2.191
100 4.264 4.264 3.873 3.873 4.846 4.846 4.264 4.264 3.873 3.873 4.458 4.458 4.263 4.846 2.763 3.346
200 4.261 4.261 3.870 3.870 4.841 4.841 4.261 4.261 3.870 3.870 4.454 4.454 4.260 4.841 2.760 3.341
MXDA 500 4.255 4.255 3.866 3.866 4.835 4.835 4.255 4.255 3.866 3.866 4.449 4.446 4.254 4.835 2.754 3.335
1200 4.249 4.249 3.861 3.861 4.827 4.827 4.249 4.249 3.861 3.861 4.442 4.442 4.248 4.827 2.748 3.327
10,000 4.227 4.227 3.843 3.843 4.798 4.798 4.227 4.227 3.843 3.843 4.418 4.418 4.226 4.798 2.726 3.298
[AA]Initial (AA from Resin and Extruder) = 1.5 ppm, Each Cavity Represents a Set of 4 Symmetric Cavities