Documente Academic
Documente Profesional
Documente Cultură
1
Feature
Tpt Systems, has launched its new “T” range post-tensioning system, complied with FIP
and the latest ETAG requirements, which has been developed for modern civil engineering
requirements and applications. They were designed not only functionally reliable but also
easily being installed by our team work know-how and accumulated experiences at the job
site operation.
We trust that through our repeated examination and improving, the T range system has
been not only highest quality systems but also economic ones. We successfully and proudly
presented an excellent post-tension system which satisfies both budget and safety to the
world.
The following information and data can help designers and users to prepare and carry
out projects with the Tpt T range system. However, the information contained in this
brochure may be changed at any time as new techniques or materials are developed.
Welcome to contact us directly for further information.
2
Strands & Ducts
Tpt systems offer engineers a complete
range of anchorage and prestressing forces
to meet the most arduous requirements,
whilst at the same time they are designed
to give trouble-free simple site operation.
The table below gives the standards of the
strands which may be used with our T range
system.
Strand standard Nominal Dia. Tensile Strength Cross Sectional Area Breaking Load
Grade 250 0.5 12.7 250 1725 0.144 92.9 36000 160.1
Grade 250 0.6 15.2 250 1725 0.216 139.4 54000 240.2
Grade 270 0.5 12.7 270 1860 0.153 98.7 41300 183.7
Grade 270 0.6 15.2 270 1860 0.217 140.0 58600 260.7
3
T rang system
Tpt systems T rage multi-force anchorages include Live End (Stressing End ), Dead
End, Anchorage Coupler and Moveable Coupler for different requirements or
application.
Tpt has dedicated to continuous research and development to provide highest standard
products. Our quality management systems comply with BS ISO 9001 and all the
products are manufactured to strict standards and high specification materials.
4
T live end anchorage
Tpt multi-force Live End Anchorage
comprises a casting force transfer
unit (FTU), a plastic deviation cone,
an anchor head and wedges. The
individual wedges grip each strand,
the anchor head transmits the load
from the strands onto the FTU and
the FTU transmits the prestressing
force into the concrete.
13mm LE No. of
A B C Ø duct* D ØE
Anchorage Strands
**T1 4 112 118 -- 45/50 40 85
T2 7 140 144 200 55/60 40 105
T3 9 150 168 184 65/70 43 125
T4 12 156 186 266 75/80 45 145
T5 17 222 225 463 80/85 58 170
T6 19 222 225 463 80/85 62 170
T7 22 266 250 519 90/95 64 190
T8 25 282 277 544 100/105 68 210
T9 27 282 277 544 100/105 72 210
T10 31 316 306 709 100/105 75 230
All dimensions in mm.
*Duct dimensions shown are for inside/outside diameter of metal sheaths.
** There is no Deviation Cone for T1 FTU.
5
T dead end anchorage
Tpt multiforce Dead End ( or
non-stressing ) Anchorage is used
when a tendon is stressed from
one end only. In the majority of
cases the non-stressing anchorage
is accessible and so the Live End
anchorage is used as passive end,
the wedges being lightly tapped
into position with the aid of a piece
of steel tubing. During stressing,
these wedges can be seen to pull
into the anchor head progressively
as load is applied to the other end
of the tendon.
15mm LE No. of
Anchorage Strands A B C Ø duct* D ØE
6
T anchorage coupler
Tpt Anchorage Coupler
is used mainly in
continuous bridge
construction where it is
essential to couple a
tendon after initially
stressing the previous
span. The coupler uses
a special Anchor Head
with radial slope on the
outer perimeter for
second stage tape hole,
thus there is no obvious
angle on the outer
wedges. And the
PATENT Spring-Hold
Ring make you install
the strands of second Spring Hold Ring
stage easily and safely.
Force Transfer Unit
Deviation Cone
Wedge
Anchor Head
7
T movable coupler
Tpt Moveable Coupler uses special
designed inline couplers to connect the
un-stressed strands of first stage to the
second stage. The strands of the
tendon are staggered to be coupled by
inline couplers to allow for a very
compact section.
Because every single strand in a tendon
is connected with an inline coupler, the
strands perform like continuous strands
while stressing. Even the strands twist
along the tendon, the inline couplers
can adapt themselves much better
than traditional Moveable Couplers.
Spring
Wedge Outer sleeve
End plug
Inline
coupler ØA L
13mm 44 160
15mm 48 168
All dimensions in mm.
8
Bursting
Reinforcemet
Anchorage ØA B ØC D N ØA B ØC D N
T1 190 240 9 50 5 180 230 9 50 5
T2 210 260 9 45 6 190 240 9 50 5
T3 280 330 13 45 7 250 300 13 50 6
T4 330 380 13 45 8.5 310 360 13 45 8
T5 370 440 16 45 10 330 400 16 45 9
T6 390 460 16 45 10.5 360 430 16 45 9.5
T7 410 480 16 45 11 380 450 16 45 10
T8 450 520 16 45 11.5 400 470 16 45 10.5
T9 460 530 20 50 10.5 420 490 20 50 10
T10 490 560 20 50 11.5 470 540 20 50 11
T11 520 590 20 50 12 500 570 20 50 11.5
T12 550 620 20 50 12.5 520 590 20 50 12
T13 580 650 20 50 13 550 620 20 50 12.5
All dimensions in mm.
*Concrete strengths shown are cylinder test strength/cube test strength.
N=No. of turns in Helix.
9
Anchor position &
Stressing pocket
10
TF Flat anchorage
Tpt flat anchorages are used mainly in slabs and transversal tendons in bridge deck. Its
compact design makes it widely use in different applications and strict working conditions.
There are 13mm and 15mm strands anchorages can be chosen for designers. The strands are
stressed individually using a mono-strand jack. The pocket for stressing can be built by our
reusable pocket former.
Pocket Former
11
TF live end anchorage
Normally the flat anchorage system mostly uses
the live end anchorage for all applications. Dead
end or non-stressing end can use the live end
anchorage instead, and basket dead end or loop
one are commonly used for dead end
applications in slab of buildings.
Once the coupler is needed, please contact us,
we will provide proper solutions for your cases
particularly.
Sheath
Flat anchorage A B C D E F G Duct
*TF1 Casting Unit Connect Sheath Duct Directly Without Plastic Deviation Cone.
All dimensions in mm.
12
Equipment
13
Accessories
We designed some accessories for your post-tensioning work. They can cost your installation
of the post-tensioning down through our longtime experiences at site. Welcome to contact
us for the further information.
14
The specification, information and performance of the products manufactured by Tpt and featured in this publication are presented in good faith and believed to be correct. Details
may be changed without notice. We make no warranties to the completeness or accuracy of the information.