Documente Academic
Documente Profesional
Documente Cultură
May, 2010
Model No.: V236H1-LE2
Approval
Customer:
Approved by:
Note:
www.jxlcd.com
www.jxlcd.com
TVHD
Approved By
Chao-Chun Chung
1 / 28
Version 2.0
Issued Date: 6. May, 2010
Model No.: V236H1-LE2
Approval
- CONTENTS -
REVISION HISTORY .............................................................................................................................3
1. GENERAL DESCRIPTION.................................................................................................................4
1.1 OVERVIEW
1.2 FEATURES
1.3 APPLICATION
1.4 GENERAL SPECIFICATIONS
1.5 MECHANICAL SPECIFICATIONS
3. ELECTRICAL CHARACTERISTICS...................................................................................................7
3.1 TFT LCD MODULE
3.1.1 Vcc POWER DIP CONDITION
3.2 BACKLIGHT UNIT
3.3 LIGHTBAR CONNECTOR PIN ASSIGNMENT
www.jxlcd.com
5.2 LVDS DATA MAPPING TABLE
www.jxlcd.com
5.3 COLOR DATA INPUT ASSIGNMENT
8. PACKAGING......................................................................................................................................21
8.1 PACKING SPECIFICATIONS
8.2 PACKING METHOD
10.RELIABILITY TEST...........................................................................................................................24
2 / 28
Version 2.0
Issued Date: 6. May, 2010
Model No.: V236H1-LE2
Approval
REVISION HISTORY
Ver 2.0 6, May, 10’ - V236H1-LE2 Approval specification was first issued.
www.jxlcd.com
www.jxlcd.com
3 / 28
Version 2.0
Issued Date: 6. May, 2010
Model No.: V236H1-LE2
Approval
1. GENERAL DESCRIPTION
1.1 OVERVIEW
V236H1-LE2 is a 23.6” TFT Liquid Crystal Display module with WLED Backlight unit and 30 pins
2ch-LVDS interface. This module supports 1920 x 1080 Full HD mode and can display up to 16.7M colors.
The converter module for Backlight is not built in.
1.2 FEATURES
- Extra-wide viewing angle.
- High contrast ratio.
- Fast response time.
- Full HD (1920 x 1080 pixels) resolution.
- DE (Data Enable) only mode.
- LVDS (Low Voltage Differential Signaling) interface.
- RoHS compliance.
www.jxlcd.com
1.3 APPLICATION
www.jxlcd.com
- TFT LCD TV / Monitor
4 / 28
Version 2.0
Issued Date: 6. May, 2010
Model No.: V236H1-LE2
Approval
80
60
Operating Range
www.jxlcd.com
40
www.jxlcd.com 20
10 Storage Range
-40 -20 0 20 40 60 80
Temperature (ºC)
Gap= 3 ~ 5 mm Bracket
5 / 28
Version 2.0
Issued Date: 6. May, 2010
Model No.: V236H1-LE2
Approval
www.jxlcd.com
www.jxlcd.com
6 / 28
Version 2.0
Issued Date: 6. May, 2010
Model No.: V236H1-LE2
Approval
3. ELECTRICAL CHARACTERISTICS
3.1 TFT LCD MODULE Ta = 25 ± 2 ºC
Value
Parameter Symbol Unit Note
Min. Typ. Max.
Power Supply Voltage Vcc 4.5 5.0 5.5 V -
Ripple Voltage VRP - - 300 mV -
Rush Current IRUSH 3 A (2)
White 0.5 0.6 A (3)a
Power Supply Current Black 1.1 1.32 A (3)b
Vertical Stripe 0.9 1.08 A (3)c
Power Consumption PLCD 5.5 6.6 Watt (4)
LVDS differential input voltage Vid 200 - 600 mV
LVDS common input voltage Vic 1.0 1.2 1.4 V
Logic High Input Voltage VIH 2.64 - 3.6 V
Logic Low Input Voltage VIL 0 - 0.66 V
Note (1) The module should be always operated within above ranges.
Note (2) Measurement Conditions:
+5.0V
Q1 2SK1475
Vcc
C3
FUSE (LCD Module Input)
R1 1uF
47K
www.jxlcd.com
www.jxlcd.com
(High to Low)
(Control Signal)
SW
+12V
R2
1K
Q2
2SK1470
47K C2
VR1
C1
0.01uF
1uF
0.9Vcc
0.1Vcc
GND
470µs
7 / 28
Version 2.0
Issued Date: 6. May, 2010
Model No.: V236H1-LE2
Approval
Note (3) The specified power supply current is under the conditions at Vcc = 5.0 V, Ta = 25 ± 2 ºC, Fr = 60
Hz, whereas a power dissipation check pattern below is displayed.
R G B R G B
B R G B R G B R
B R G B R G B R
R G B R G B
www.jxlcd.com
www.jxlcd.com
Active Area
Note (4)The power consumption is specified at the pattern with the maximum current
Note (5) VID waveform condition
8 / 28
Version 2.0
Issued Date: 6. May, 2010
Model No.: V236H1-LE2
Approval
4.5V
4.0V
Td
www.jxlcd.com
www.jxlcd.com
LED Light Bar Current
Per Input Pin
LED Life Time
Power Consumption
IPIN
LLED
PBL
0
30000
---
40
12.3
50
13.5
mA
Hrs
W
(1), (2)
Duty=100%
(3)
(1)
Duty=100%,
IPIN=40mA
Note (1) LED light bar input voltage and current are measured by utilizing a true RMS multimeter as shown
below:
Note (2) PBL = IPIN × VPIN × ( 8 ) input pins , LED light bar circuit is (12)Series, (8)Parallel.
Note (3) The lifetime of LED is defined as the time when LED packages continue to operate under the
conditions at Ta = 25 ±2 ℃ and I= (20)mA (per chip) until the brightness becomes ≦ 50% of its
original value.
VPIN , IPIN(8)
Function generator
9 / 28
Version 2.0
Issued Date: 6. May, 2010
Model No.: V236H1-LE2
Approval
www.jxlcd.com
www.jxlcd.com Pin 1 define
10 / 28
Version 2.0
Issued Date: 6. May, 2010
Model No.: V236H1-LE2
Approval
4. BLOCK DIAGRAM
4.1 TFT LCD MODULE
RXO0(+/-)
RXO1(+/-)
SCAN DRIVER IC
LVDS INPUT /
RXO2(+/-)
(STM MSCKT2407P30HA
RXO3(+/-) (1920x3x1080)
or Equivalent )
RXOC(+/-)
RXE0(+/-)
RXE1(+/-)
RXE2(+/-)
RXE3(+/-)
DATA DRIVER IC
RXEC(+/-)
NC
DC/DC CONVERTER &
Vcc REFERENCE VOLTAGE
GND
VLED
BACKLIGHT UNIT
ILED
www.jxlcd.com
www.jxlcd.com
11 / 28
Version 2.0
Issued Date: 6. May, 2010
Model No.: V236H1-LE2
Approval
12 / 28
Version 2.0
Issued Date: 6. May, 2010
Model No.: V236H1-LE2
Approval
www.jxlcd.com
www.jxlcd.com
13 / 28
Version 2.0
Issued Date: 6. May, 2010
Model No.: V236H1-LE2
Approval
Green(0) / Dark 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Green(1) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0
www.jxlcd.com
Green(2) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0
www.jxlcd.com
Gray
: : : : : : : : : : : : : : : : : : : : : : : : :
Scale
: : : : : : : : : : : : : : : : : : : : : : : : :
Of
Green(253) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 0 1 0 0 0 0 0 0 0 0
Green
Green(254) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0
Green(255) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
Blue(0) / Dark 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Blue(1) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
Blue(2) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
Gray
: : : : : : : : : : : : : : : : : : : : : : : : :
Scale
: : : : : : : : : : : : : : : : : : : : : : : : :
Of
Blue(253) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 0 1
Blue
Blue(254) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0
Blue(255) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
Note (1) 0: Low Level Voltage, 1: High Level Voltage
14 / 28
Version 2.0
Issued Date: 6. May, 2010
Model No.: V236H1-LE2
Approval
6. INTERFACE TIMING
6.1 INPUT SIGNAL TIMING SPECIFICATIONS
The input signal timing specifications are shown as the following table and timing diagram.
Signal Item Symbol Min. Typ. Max. Unit Note
Frequency Fc 58.54 74.25 98 MHz -
Period Tc - 13.47 - ns
Input cycle to
Trcl -0.02*Tc - 0.02*Tc ns (1)
cycle jitter
Spread
spectrum
modulation Fclkin_mod 0.98*Fc - 1.02*Fc MHz
LVDS Clock
range
(2)
Spread
spectrum
FSSM - - 200 KHz
modulation
frequency
High Time Tch - 4/7 - Tc -
Low Time Tcl - 3/7 - Tc -
Setup Time Tlvs 600 - - ps
LVDS Data (3)
Hold Time Tlvh 600 - - ps
Frame Rate Fr 50 60 75 Hz Tv=Tvd+Tvb
Total Tv 1115 1125 1136 Th -
Vertical Active Display Term
Display Tvd 1080 1080 1080 Th -
Blank Tvb 35 45 56 Th -
Total Th 1050 1100 1150 Tc Th=Thd+Thb
Horizontal Active Display Term Display Thd 960 960 960 Tc -
www.jxlcd.com
Blank Thb 90 140 190 Tc -
Note:
www.jxlcd.com
Because this module is operated by DE only mode, Hsync and Vsync input signals are ignored.
Tv
TVd TVb
DE
Th
DCLK
TC
Thb Thd
DE
DATA
15 / 28
Version 2.0
Issued Date: 6. May, 2010
Model No.: V236H1-LE2
Approval
Note (1) The input clock cycle-to-cycle jitter is defined as below figures. Trcl = I T1 – TI
T T1
Note (2) The SSCG (Spread spectrum clock generator) is defined as below figures.
www.jxlcd.com
www.jxlcd.com
Note (3) The LVDS timing diagram and setup/hold time is defined and showing as the following figures.
LVDS RECEIVER INTERFACE TIMING DIAGRAM
Tc
RXCLK+/-
RXn+/-
Tlvs
Tlvh
1T 3T 5T 7T 9T 11T 13T
14 14 14 14 14 14 14
16 / 28
Version 2.0
Issued Date: 6. May, 2010
Model No.: V236H1-LE2
Approval
90% 90% t4
t2 t3
- Interface Signal
Valid Data
(LVDS Signal of 0V
Transmitter), VI
t5 t6
50% 50%
OFF ON OFF
- Power for Backlight
Timing Specifications:
0.5< t1 ≦ 10 msec
0 < t2 ≦ 50 msec
www.jxlcd.com
0 < t3 ≦ 50 msec
www.jxlcd.com
t4 ≧ 500 msec
t5 ≧ 450 msec
t6 ≧ 90 msec
5< t7 ≦ 100 msec
Note.
(1) The supply voltage of the external system for the module input should be the same as the definition of Vcc.
(2) When the backlight turns on before the LCD operation of the LCD turns off, the display may momentarily
become abnormal screen.
(3) In case of VCC = off level, please keep the level of input signals on the low or keep a high impedance.
(4) T4 should be measured after the module has been fully discharged between power off and on period.
(5) Interface signal shall not be kept at high impedance when the power is on.
(6) It is not guaranteed that products are damaged which is caused by not following the Power Sequence.
(7) It is suggested that Vcc falling time follows t7 specification, else slight noise is likely to occur when LCD
is turned off (even backlight is already off).
17 / 28
Version 2.0
Issued Date: 6. May, 2010
Model No.: V236H1-LE2
Approval
7. OPTICAL CHARACTERISTICS
7.1 TEST CONDITIONS
Item Symbol Value Unit
o
Ambient Temperature Ta 25±2 C
Ambient Humidity Ha 50±10 %RH
Supply Voltage VCC 5 V
Input Signal According to typical value in "3. ELECTRICAL CHARACTERISTICS"
LED Light Bar Input Current
IPIN 40 ± 1.2 mADC
Per Input Pin
PWM Duty Ratio D 100 %
LED Light Bar Test Converter CMO 27-D041745
www.jxlcd.com
www.jxlcd.com
White
LC
CR
250
700
0.329
300
1000
-
-
cd/m
-
2
(4), (5)
(2), (5)
TR - 1.5 2.5
Response Time θx=0°, θY =0° ms (3)
TF - 3.5 5.5
θx=0°, θY =0°
White Variation δW - - 1.33 - (5), (6)
USB2000
x- +
Horizontal 150 170 -
x+ CR ≧ 10
Viewing Angle Deg. (1), (5)
y- + USB2000
Vertical 140 160 -
y+
x- + 160
Horizontal 178 ---
x+ CR ≧ 5
Viewing Angle Deg. (1), (5)
y- + USB2000 150
Vertical 170 ---
y+
18 / 28
Version 2.0
Issued Date: 6. May, 2010
Model No.: V236H1-LE2
Approval
Normal
θx = θy = 0º
θy- θy+
6 o’clock
y- x+ θX+ = 90º
θy- = 90º
www.jxlcd.com
www.jxlcd.com
L 0: Luminance of gray level 0
CR = CR (5)
CR (X) is corresponding to the Contrast Ratio of the point X at Figure in Note (6).
90%
Optical
Response
Gray Level 0
10%
0%
Time
TR TF
66.67ms 66.67ms
19 / 28
Version 2.0
Issued Date: 6. May, 2010
Model No.: V236H1-LE2
Approval
LCD Module
LCD Panel
USB2000 CS-2000
CS-1000T
www.jxlcd.com
www.jxlcd.com 500 mm
Light Shield Room
(Ambient Luminance < 2 lux)
Note (6) Definition of White Variation (δW):Measure the luminance of gray level 255 at 9 points
δW = Maximum [L (1) ~ L (9)] / Minimum [L (1) ~ L (9)]
Horizontal Line
D
D/10 D/2 D/10
W/10 1 2 3
Vertical Line
W/10 7 8 9
Active Area
20 / 28
Version 2.0
Issued Date: 6. May, 2010
Model No.: V236H1-LE2
Approval
8. PACKAGING
8.1 PACKING SPECIFICATIONS
(1) 11 LCD modules / 1 Box
(2) Box dimensions: 620(L) X 348(W) X 430(H) mm
(3) Weight: approximately: 30.1kg (11 modules per box)
www.jxlcd.com
www.jxlcd.com
21 / 28
Version 2.0
Issued Date: 6. May, 2010
Model No.: V236H1-LE2
Approval
Sea / Land Transportation (40ft HQ Container) Sea / Land Transportation (40ft Container)
Corner Protector
(50*50*1000mm)
PP Belt
Corner Protector
Film
(50*50*800mm)
PE Sheet
Corner Protector
PE Sheet
(50*50*1250mm) Corner Protector
Film (50*50*800mm)
Film
Pallet Pallet
(1250*1050*143mm) (1250*1050*143mm)
PE Sheet
Corner Protector
(50*50*1250mm)
Film
Pallet
(1250*1050*143mm)
Carton label
22 / 28
Version 2.0
Issued Date: 6. May, 2010
Model No.: V236H1-LE2
Approval
9. DEFINITION OF LABELS
The barcode nameplate is pasted on each module as illustration, and its definitions are as following explanation.
CHI MEI
OPTOELECTRONICS V236H1 –LE2 Rev.
RoHS
XXXXXXXYMDLNNNN
Serial No.
CMO Internal Use
Year, Month, Date
CMO Internal Use
Revision
www.jxlcd.com
www.jxlcd.com CMO Internal Use
(c) Production Location: MADE IN XXXX. XXXX stands for production location.
(d) UL Factory ID:
Region Factory ID
TWCMO GEMN
NBCMO LEOO
NBCME CANO
NHCMO CAPG
23 / 28
Version 2.0
Issued Date: 6. May, 2010
Model No.: V236H1-LE2
Approval
www.jxlcd.com
www.jxlcd.com
24 / 28
Version 2.0
Issued Date: 6. May, 2010
Model No.: V236H1-LE2
Approval
11. PRECAUTIONS
11.1 ASSEMBLY AND HANDLING PRECAUTIONS
(1) Do not apply rough force such as bending or twisting to the module during assembly.
(2) To assemble or install module into user’s system can be only in clean working areas. The dust and oil
may cause electrical short or worsen the polarizer.
(3) It’s not permitted to have pressure or impulse on the module because the LCD panel and Backlight will
be damaged.
(4) Always follow the correct power sequence when LCD module is connecting and operating. This can
prevent damage to the CMOS LSI chips during latch-up.
(5) Do not pull the I/F connector in or out while the module is operating.
(6) Do not disassemble the module.
(7) Use a soft dry cloth without chemicals for cleaning, because the surface of polarizer is very soft and
easily scratched.
(8) It is dangerous that moisture come into or contacted the LCD module, because moisture may damage
LCD module when it is operating.
(9) High temperature or humidity may reduce the performance of module. Please store LCD module within
the specified storage conditions.
(10) When ambient temperature is lower than 10ºC may reduce the display quality. For example, the
www.jxlcd.com
response time will become slowly,
www.jxlcd.com
11.2 SAFETY PRECAUTIONS
(1) If the liquid crystal material leaks from the panel, it should be kept away from the eyes or mouth. In
case of contact with hands, skin or clothes, it has to be washed away thoroughly with soap.
(2) After the module’s end of life, it is not harmful in case of normal operation and storage.
11.4. Storage
(1) Do not leave the module in high temperature, and high humidity for a long time.
It is highly recommended to store the module with temperature from 0℃ to 35℃
And relative humidity of less than 70%
(2) Do not store the TFT – LCD module in direct sunlight
(3) The module should be stored in dark place. It is prohibited to apply sunlight or fluorescent light in storing
25 / 28
Version 2.0
Issued Date: 6. May, 2010
Model No.: V236H1-LE2
Approval
11.6 OTHER
When fixed patterns are displayed for a long time, remnant image is likely to occur.
www.jxlcd.com
www.jxlcd.com
26 / 28
Version 2.0
Issued Date: 6. May, 2010
Model No.: V236H1-LE2
Approval
www.jxlcd.com
www.jxlcd.com
27 / 28
Version 2.0
Issued Date: 6. May, 2010
Model No.: V236H1-LE2
Approval
www.jxlcd.com
www.jxlcd.com
28 / 28
Version 2.0