Documente Academic
Documente Profesional
Documente Cultură
This will allow you to run homebrew and backup manager on your PlayStation 3.
This tutorial was written/tested under a Windows 7 x64/x86(32 bit). Other Windows
operating versions should work just fine.
5.
6. A wizard should pop up, select the advanced option.
7.
8. Highlight "Show All Devices" and click Next.
9. Click "Have Disk", then browse where ever you installed Amtel, the default should
be here:C:\Program Files (x86)\Atmel\Flip 3.4.1\usb\
10. Select atmel_usb_dfu.inf
11. Once driver is installed, press the RESET button on Blackcat again, and it should
show correctly on Device Manager.
Your done, and should have successfully flashed PSGroove on your Blackcat
Now all you have to do is boot your PS3 properly with your PSgroove flashed USB board
1. Go to http://www.rockbox.org/download/ and download the automatic
installer.
2. Once it is downloaded, open up RockboxUtility. Now plug in your iPod to
your computer. Your device should pop up where it says "Selected Device"
NOTE: For it to work your device must be in Disk Mode. An easy way to
tell is by going to my computer, and see if your iPod is detected there.
Also open up iTunes Select your Device, under Options there should be a
check for "Enable disk use"
5. Once this is finished you have Rockbox installed on your iPod. Reboot
your ipod by holding down MENU and SELECT (middle of the clickwheel)
NOTE: You cannot just remove the .2 from the rb.psgroove.patch.2. This
file needs to be COMPILED with the original rockbox.ipod for NANO 1G or
Video 5g. Dont assume all the work has been done for you.
2. Once you have the correct rockbox.ipod file, copy it to the ".rockbox"
folder, overwriting the original rockbox.ipod.
You are done, you now have the PSGROOVE exploit on your iPod.
http://sourceforge.net/projects/rbpsgroove/
.pkg files can now be placed on the root of another thumb drive and
opened from Install Package Files. Dont worry if you have no access to
/app_home/PS3_GAME/
**
USE THIS TUTORIAL AT YOUR OWN RISK, I AM NOT RESPONSIBLE
FOR ANYTHING THAT COULD HAPPEN DURING THE PROCRESS**
Step-By-Step
http://appldnld.apple.com.edgesuite....3_Restore.ipsw
4. What you need to do now is to click on the little button on the bottom
left of the screen of your iPhone when Android as loaded. It will bring you
to the main menu of openiboot.
5. Now, with the volume down button you will need to go to Install on the
bottom left of the screen and press the Home button.
6. After the installation is done, Click the Home button on the Apple Logo
to go back to your Iphone.
8. Make sure you have OpenSSH on your iphone for the next steps
9. Load iFunbox
10. Go in the directory of your iPhone, click on Raw File System, click on
Private and then click on VAR
11. Now that you're in the VAR folder, you will need to drag and drop the
2 files of PSFreedom in that folder. make sure you've dragged them and
they are the correct size!
13. On your iPhone you will have to go in Settings-- Wifi-- click on the
blue arrow next to your Wifi
14. Write down the IP Address of your iPhone to the Host Name in WinSCP
16. Click on the open folder on the right upper corner. enter this in the
address ''/private/var'' without the quotes.
it will bring you to the folder where the 2 files of PSFreedom are.
17. right click on each files that you added: zImage and android.img.gz
go to properties and put 0777 to the permissions of both files. make sure
the boxes are checked!
18. turn the iPhone off, turn it back on. go to your PS3 switch the power
to off.
plug the iPhone, switch the power back ON to your ps3, but do not boot it
right away.
Loading kernal...
Loading initrd...
Minimus board
FLIP software to flash a hex file to
board:http://www.atmel.com/dyn/products/tools … ol_id=3886
Device drivers for the
minimus:http://www.minimususb.com/files/minimus_x64_drivers.rar
Hex file to flash to minimus: http://www.ps3-
hacks.com/download.php?id=95 (Use the "psgroove_backups.hex")
PS3 at firmware NO HIGHER THAN 3.41
An official blu-ray game disc (Any will do)
Backup manager package file (google it)
Right click "My Computer", click "Manage", then click on "Device Manager" in the left
hand menu
Find the minimus in the list of devices, right click, click "update device drivers", and
locate your unzipped folder (link above).
Click: File -> Load HEX File (link above to correct hex file)
Check if the file name is correct, then press RUN to program chip (Sometimes when you
press RUN, nothing happens, if so, click it again)
Check if it says "Verify Pass" at the bottom
Hex file should be loaded, now you can safely unplug the device from the PC.
Here is a link to the official PDF help file detailing how to flash a hex to the minimus.
http://www.minimususb.com/minimus_v13.pdf
Now that you have the hex file flashed to the minimus AVR, the hard part is over.
Games with INDIVIDUAL file sizes larger than 4GB cannot be backed up to an external
drive, as the PS3 only supports FAT32 for external drives.
To copy a backed up game to the PC, use the following FTP program to copy it.
5.
6. Then make sure under "TI Device Applications" that "Device Operating System" is
checked.
7.
8. Choose your TI-84+ when it starts scanning and click select
9. At this point, if there is an update for your calculator it will prompt to for your
username and password (you can create an account for free on TI's website).
Install the update and continue to the next section.
4.
5. You now need to drag and drop the PS3JB.8XK file to the applications section that
you just expanded. If done correctly, you will see "PS3JB" listed under
Applications.
6.
Congratulations, you have successfully transfered over the exploit to your calculator.
Continue to the next step to install the exploit onto your PS3.
1. This is simple, once downloaded, simply transfer the package file onto a FAT32
formatted USB flash drive.
1. Turn your Playstation 3 completely off. Switch the power button on the back to
off, or unplug it from the power outlet.
2. On your calculator, press the "APPS" key and scroll down, you should see PS3JB.
Select it and hit Enter.
3. You will see a splash screen with a version number, press any key to continue,
then press 1 to start the exploit. Now, connect your calculator to your playstation
3 via USB. You will see this screen.
4. Flip the power switch on the back of your PS3 to on, or plug your playstation 3
back into the power outlet and turn it on, then QUICKLY press the eject button (I
press it several times to make sure). It will say "Working...", then eventually
switch to "Working...Done".
5. Go to Games under the XMB, you will see 2 new items. "Install Package File" and
"/app_home/PS3_Game/". If you see these 2 items, congratulations, you've
activated the exploit. Now onto installing backup manager.
1. Plug in your USB Flash drive (with the backup manager package on it). Then, go
to "Install PackageFile" under the Game XMB and you should see "manager.pkg",
select it.
2. It will prompt you with piracy warnings, accept if you agree and you will have
installed Backup Manager.
1. Insert a game
2. Under the Game XMB, select backup manager
3. Once backup manager loads, you will see the game you inserted into the drive
and it will give you the option to Load or Backup (Circle). Press Circle to
backup your game.
4. It will give you the option to install it to an internal or external drive, choose
whichever you want.
5. The game will now start backing up to your hard drive
6. Once finished, backup manager will return to its initial screen and you will be able
to view your backed up games.
1. Activate the exploit using your calculator (by going into APPS and selecting
PS3JB...)
2. In the Game XMB, select Backup Manager
3. Insert any Blu-ray disc into the PS3
4. Select the game you wish you play, it will kick you back to the game XMB- but
the game you selected will be mounted and show up as a blu-ray disc. Select it
and enjoy :-)
Here's a video since some people are having trouble playing the backed up video games.
IX. FAQ:
KaKaRoTo released his PSGroove clone for the Nokia N900, it is not a port of PSGroove.
You can find the news post here, however due to huge load the site went down
Instructions to install this, you need the stock kernel rootsh and wget installed for now.
Code:
root
wget http://xceleo.org/psfreedom.tar.gz
tar -xzvf psfreedom.tar.gz
chmod +x *.sh
./psfreedom-enable.sh
Turn off the PS3 from the back power switch, plug the N900 in, flip the switch on the
back, then press the power button and in less than 200ms the eject button.
The PS3 should now be jailbroken, check with dmesg on the N900 to see if it succeeded.