Documente Academic
Documente Profesional
Documente Cultură
T4D0BP-006
1
SHENZHEN ORIC ELECTRONICS CO., LTD.
REVISION STATUS
2
SHENZHEN ORIC ELECTRONICS CO., LTD.
TABLE OF CONTENTS
REVISION STATUS................................................................................................................................... 2
TABLE OF CONTENTS.............................................................................................................................3
1. GENERAL DESCRIPTION.................................................................................................................... 4
2. MECHANICAL SPECIFICATION..........................................................................................................5
3. PIN DESCRIPTION............................................................................................................................... 6
4. ELECTRICAL CHARACTERISTICS......................................................................................................7
5.INPUT SIGNAL TIMING.....................................................................................................................10
6. OPTICAL CHARACTERISTICS.......................................................................................................... 13
7.QUALITY ASSURANCE SYSTEM....................................................................................................... 16
8. PRECAUTION RELATING PRODUCT HANDLING..........................................................................17
9. PACKAGE DRAWING.........................................................................................................................18
3
SHENZHEN ORIC ELECTRONICS CO., LTD.
1. GENERAL DESCRIPTION
1.1 DESCRIPTION
This LCM is a color active matrix thin film transistor(TFT) liquid crystal display (LCD) that
uses amorphous silicon TFT as a switchingdevice. Thismodule is composed of a TFT LCD panel,
driver IC, FPC and a Backlight unit.
1.2 FEATURES:
No. Item 项目 Specification 规格 Unit 单位 Remark
12 Weight 重量 TBD g -
4
SHENZHEN ORIC ELECTRONICS CO., LTD.
2. MECHANICAL SPECIFICATION
SHENZHEN ORIC ELECTRONICS CO.,LTD.
5
SHENZHEN ORIC ELECTRONICS CO., LTD.
3. PIN DESCRIPTION
LCM Pin Assignments 接口定义
Pin 序
Symbol 符号 Function 功能描述
号
1 LEDK LED Cathode4
3 GND Ground
6
SHENZHEN ORIC ELECTRONICS CO., LTD.
4. ELECTRICAL CHARACTERISTICS
4.1 ABSOLUTE MAXIMUM RATINGS
Values
Item Symbol Unit Remark
Min. Max.
Digital Supply Voltage VDD -0.3 4.0 V
4.2.2Current Consumption
Values
Item Symbol Condition Unit Remark
Min. Typ. Max.
Digital Current IVDD VDD= 3.3V - 160 - mA
Total Power
PC - TBD TBD mW
Consumption
7
SHENZHEN ORIC ELECTRONICS CO., LTD.
4.3BACKLIGHT UNIT
Item Symbol Min. Typ. Max. Unit
8
SHENZHEN ORIC ELECTRONICS CO., LTD.
9
SHENZHEN ORIC ELECTRONICS CO., LTD.
10
SHENZHEN ORIC ELECTRONICS CO., LTD.
11
SHENZHEN ORIC ELECTRONICS CO., LTD.
12
SHENZHEN ORIC ELECTRONICS CO., LTD.
6. OPTICAL CHARACTERISTICS Ta = 25 ± 2℃
Left θL 80 85 -
Viewing
Right θR 80 85 -
Angle Range
CR≧10 degree
Top θT 80 85 -
视角
Bottom θB 80 85 -
Response Time Ta=25℃
Ton+Toff - 35 - ms
响应时间 θ=Ф=0˚
Contrast Ratio
CR θ=Ф=0˚ 550 800 - -
对比度
Flicker 闪烁 - - 小于等于20% -
13
SHENZHEN ORIC ELECTRONICS CO., LTD.
Note1: Definition of optical measurement system (BM-7)
θL
θT θR
=180° θB =0°
Active Area
=270°
6 o'clock direction
100%
(Relative value)
90%
10%
0%
TON TOFF
15
SHENZHEN ORIC ELECTRONICS CO., LTD.
7.QUALITY ASSURANCE SYSTEM
7.1 TEMPERATURE AND HUMIDITY
Test Item Test Condition Remark
IEC60068-2-1:2007
HighTemperatureStorage Ta=60℃; 120hrs
GB2423.2-2008
IEC60068-2-1:2007
Low Temperature Storage Ta=-10℃;120hrs
GB2423.1-2008
IEC60068-2-1:2007
High Temperature Operation Ta=50℃,120Hrs
GB2423.2-2008
IEC60068-2-1:2007
LowTemperatureOperation Ta=0℃; 120hrs
GB2423.1-2008
HighTemperatureHighHumidity Ta=40℃,80%RH, IEC60068-2-78:2001
Operation 120Hrs(no condensation) GB/T2423.3-2006
Startwith cold temperature ,
-10℃(0.5h) ~ 60℃(0.5h)
Thermal Shock End with high temperature,
/ 100cycles
IEC60068-2-14:1984,GB2423.22-2002
Image Sticking 25℃ ; 1hrs Note1
Operation with test pattern sustained for 1 hrs,then change to gray pattern immediately.after
5 mins,themura must be disappeared completely
7.2 VIBRATION&SHOCK
Test item Conditions Remark
Packing Shock 980m/s2,6ms, ±x,y,z 3times for IEC60068-2-27:1987
(non-operation) direction GB/T2423.5-1995
Frequency range:10 HZ~50HZ
Packing Vibration IEC60068-2-32:1990
Stroke:1.0mm,sweep:10 HZ ~50HZ
(non-operation) GB/T2423.8-1995
x,y,z 2 hours for each direction
7.3ESD
Test item Conditions Remark
Electro Static 150pF,330Ω,
1
Discharge Test Contact:±4KV,Air:±8KV Class B
(non-operation) 200pF,0Ω,±200V contact test 2
Note: Measure point :
1. LCD glass and metal bezel ; 2. IF connector pins
3.ESD class B:some performance degradation allowed. Self-recoverable. No data lost,no
hardware failures.
16
SHENZHEN ORIC ELECTRONICS CO., LTD.
8. GENERAL PRECAUTION
8.1 SAFETY
1. Do not swallow any liquid crystal, even if there is no proof that liquid crystal ispoisonous.
2. If the LCD panel breaks, be careful not to get liquid crystal to touch your skin.
3. If skin is exposed to liquid crystal, wash the area thoroughly with alcohol or soap.
8.2 STORAGE CONDITIONS
1. Store the panel or module in a dark place where the temperature is 23±5°C
andThehumidity is below 50±20%RH.
2. Store in anti-static electricity container.
3. Store in clean environment, free from dust, active gas, and solvent.
4. Do not place the module near organics solvents or corrosive gases.
5. Do not crush, shake, or jolt the module.
8.3 HANDLING PRECAUTIONS
1. Avoid static electricity which can damage the CMOS LSI.
2. The polarizing plate of the display is very fragile. So, please handle it verycarefully.
3. Do not give external shock.
4. Do not apply excessive force on the surface.
5. Do not wipe the polarizing plate with a dry cloth, as it may easily scratch theSurface of
plate.
6. Do not use ketonics solvent & Aromatic solvent, use with a soft cloth soaked witha
cleaning naphtha solvent.
7. Do not operate it above the absolute maximum rating.
8. Do not remove the panel or frame from the module.
9. When the module is assembled, it should be attached to the system firmly,Be careful
not to twist and bend the module.
10. Wipe off water droplets or oil immediately. If you leave the droplets for a long
time,staining and discoloration may occur.
11. If the liquid crystal material leaks from the panel, it should be kept away from the
eyesormouth in case of contact with hands, legs or clothes, it must be
washedawaythoroughly with soap.
8.4 WARRANTY
1.The period is within twelve months since the date of shipping out under normal using and
storage conditions.
2. Do not repaired or modified the LCM. It may cause function to lose efficacy,Starry does
not warrant the LCM.
3. All process and material comply ROHS.
17
SHENZHEN ORIC ELECTRONICS CO., LTD.
9. Package Drawing
(1) (2)
(3) (4)
(5) (6)
3. Put 1 foam under the tray stack and 1 foam above. 在托盘上下放卡板.
4. Fix the cardboard to the tray stack with adhesive tape. 绑胶带.
18