Documente Academic
Documente Profesional
Documente Cultură
Juniper
Exam JN0-347
Enterprise Routing and Switching, Specialist (JNCIS-ENT)
Version: 8.0
[ Total Questions: 65 ]
Juniper JN0-347 : Practice Test
Question No : 1
You disconnected a switch from the Virtual Chassis, but the disconnected switch’s member
ID is still displayed in the status output.
Answer: D
Question No : 2
You have deployed a Juniper EX Series switch in the network. The switch receives a
broadcast frame on an interface.
A. The frame is flooded out all portsthat are part of the same VLAN as the receiving port,
except for the port on which the frame was received.
B. The frame is flooded out all ports in all VLANs configured on the switch.
C. The frame is re-transmitted as a multicast frame on all ports on theswitch.
D. The frame is flooded out all ports that are part of the same VLAN as the receiving port,
including the port on which the frame was received.
Answer: A
Question No : 3
You are adding a new EX4300 member switch to your existing EX4300 Virtual Chassis.
However, the new member is not running the same Junos version as the other members.
2
Juniper JN0-347 : Practice Test
A. The new switch is not recognized by the Virtual Chassis.
B. The Virtual Chassis will transition into a split brain situation between the existing master
Routing Engine and the switch running the different version.
C. The new switch will be assigned a member ID and then placed in an inactive state.
D. The new switch will automatically pull the correct version from the master Routing
Engine and perform the necessary upgrade.
Answer: C
Question No : 4
You are configuring a new BGP service to your service provider. You want to ensure that
BGP is fully established and has all the routes in the route table before allowing traffic to
transit the router.
Answer: D
Question No : 5
Which protocol prevents loops and calculates the best path through a switched network
that contains redundant paths?
A. VRRP
B. STP
C. DHCP
D. IS-IS
Answer: B
3
Juniper JN0-347 : Practice Test
Question No : 6
You have an existing Virtual Chassis consisting of five member devices. Member 3 fails
and must be replaced. You remove the EX Series switch with a Member ID of 3 and install
a replacement switch in its place using identical cabling as shown in the exhibit. The
replacement’s member ID is 6, so the configuration for member ID 3 is not applied to it.
Referring to the exhibit, what should have been done before installing the replacement
switch?
Answer: B
Question No : 7
4
Juniper JN0-347 : Practice Test
A. A local address statement with the lo0 address must be added to R2 undergroup
external-a.
B. An import policy statement must be added to R2 undergroup external-ato allow ISP-B to
peer.
C. Thetype externalstatement must be added to R2 undergroup external-b.
D. Thepeer-asstatement needs the AS number for ISP-B.
Answer: D
Question No : 8
You are troubleshooting your OSPF configuration and notice that you have subnet
mismatch errors when running the show ospf statistics command.
Which two actions would further troubleshoot the errors? (Choose two.)
5
Juniper JN0-347 : Practice Test
Answer: A,D
Question No : 9
Answer: D
Question No : 10
6
Juniper JN0-347 : Practice Test
Referring to the exhibit, which two statements are correct? (Choose two.)
Answer: C,D
Question No : 11
7
Juniper JN0-347 : Practice Test
Referring to the exhibit, which three statements are true? (Choose three.)
8
Juniper JN0-347 : Practice Test
C. The switch cannot be managed through the production network.
D. Frames on interface ge-0/0/2 can be tagged with VLAN ID 101 or VLAN 1.
E. Frames on interface ge-0/0/0 can be tagged with VLAN ID 101.
Answer: A,C,E
Question No : 12
9
Juniper JN0-347 : Practice Test
A. The ISO address is not configured on interface ge-0/0/1.
B. Thelevel is not configured underprotocols isis.
C. The IP address is not configured on interface lo0.
D. The link MTU is too small on interface ge-0/0/1.
Answer: D
Explanation: https://www.netflask.net/isis-minimum-mtu/
Question No : 13
You are monitoring your IS-IS router and issue the command shown in the exhibit.
10
Juniper JN0-347 : Practice Test
D. The name of the local device is r1.
Answer: B,C
Question No : 14
Which two statements are true about the IRB interface? (Choose two.)
Answer: A,C
Question No : 15
11
Juniper JN0-347 : Practice Test
You created a policy to reject all incoming routes from peer 2.2.2.2. You notice that despite
applying the policy, you are still receiving routes from this peer.
Referring to the exhibit, why are you still receiving the routes?
12
Juniper JN0-347 : Practice Test
C. The policy should be an import policy.
D. You cannot block incoming IBGP routes.
Answer: C
Question No : 16
Which three statements are true regarding not-so-stubby areas (NSSAs)? (Choose three.)
Answer: A,B,E
Question No : 17
A. Tunnel endpoints must have static routes pointing to the remote endpoints.
B. You must configurethe tunnel on the physical interface connecting to the remote
endpoint.
C. You must be able to reach the remote endpoint through the tunnel.
D. Tunnel endpoints must have a route that directs traffic into the tunnel.
Answer: D
Question No : 18
13
Juniper JN0-347 : Practice Test
A routing table contains multiple BGP routes to the same destination prefix. The route
preference is the same for each route.
A. route B
B. route D
C. route A
D. route C
Answer: B
Question No : 19
14
Juniper JN0-347 : Practice Test
What would cause the status of interface ge-0/0/8 as shown in the exhibit?
Answer: D
Question No : 20
You are asked to ensure that a designated interface on an EX Series switch only allows a
specific server to pass traffic.
Which two features are required to satisfy this solution? (Choose two.)
15
Juniper JN0-347 : Practice Test
A. IP source guard
B. proxy ARP
C. MAC limiting
D. persistent MAC learning
Answer: C,D
Question No : 21
16
Juniper JN0-347 : Practice Test
You are performing network tests and notice that the Layer 3 interface in the Finance VLAN
on an EX Series switch is not responding to pings. You review the device status from the
console.
17
Juniper JN0-347 : Practice Test
What is causing the problem, as shown in the exhibit?
Answer: A
Explanation:
https://kb.juniper.net/InfoCenter/index?page=content&id=KB26488&actp=METADATA
Question No : 22
A. The frame is sent out all ports assigned to all configured VLANs except the ingress port
on whichthe frame was received.
B. The frame is sent out all access ports associated with the ingress VLAN regardless of
whether a matching MAC address was found in the bridge table.
C. The frame is sent out all ports assigned to the associated VLAN except the ingress port
on which the frame was received.
D. The frame is sent out all trunk ports associated with the ingress VLAN regardless of
whether a matching MAC address was found in the bridge table.
Answer: C
Question No : 23
Which two statements are true about link aggregation groups (LAGs)? (Choose two.)
18
Juniper JN0-347 : Practice Test
A. Member links must use contiguous ports on the same member switch.
B. Duplex and speedsettings are not required to match on both participating devices.
C. If one-member link fails, the LAG can continue to carry traffic over the remaining links.
D. LAGs increase available bandwidth based on the number of member links.
Answer: C,D
Question No : 24
What will be two results of the OSPF configuration shown in the exhibit? (Choose two.)
Answer: A,B
Question No : 25
19
Juniper JN0-347 : Practice Test
Click the Exhibit button.
You are asked to change the default behavior of your trunk port (ge-0/0/1) to now pass
untagged traffic.
A. set interfaces ge-0/0/1 native-vlan-id 1set interfaces ge-0/0/1 unit 0 family ethernet-
switching interface mode trunk vlan members vlan.1
B. set interfaces ge-0/0/1 native-vlan-id 1set interfaces ge-0/0/1 unit 0 family ethernet-
switchinginterface mode trunk vlan members native
C. set interfaces ge-0/0/1 native-vlan-id 1set interfaces ge-0/0/1 unit 0 family ethernet-
switching interface mode trunk vlan members 1
D. set interfaces ge-0/0/1 native-vlan-id 1set interfaces ge-0/0/1 unit 0family ethernet-
switching interface mode trunk vlan members native_v1
Answer: C
20
Juniper JN0-347 : Practice Test
Question No : 26
Which three mechanisms are associated with the bridging process? (Choose three.)
A. pruning
B. listening
C. learning
D. filtering
E. flooding
Answer: C,D,E
Question No : 27
A. They must be supported in all BGP implementations, but do not have to be included in
every BGP update.
B. If they are not recognized, they are ignored and not passed to other peers.
C. They must be supported by all BGP implementations and must be included in every
BGP update.
D. Although not required, they should be passedalong, unchanged to other BGP peers
when included.
Answer: D
Question No : 28
There is a GRE tunnel configured over the Internet between Router-1 and Router-2. An
OSPF adjacency is configured over this GRE tunnel. However, the OSPF adjacency briefly
reaches the Full state before it is torn down. This cycle repeats indefinitely.
Which two actions would you perform to solve this problem? (Choose two.)
21
Juniper JN0-347 : Practice Test
C. Configure the physical WAN interfaces on both routers as passive OSPF interfaces.
D. Configure static routes to the tunnel endpoints.
Answer: A
Question No : 29
Referring to the exhibit, which effect does the configuration on R2 have on OSPF routing in
the network?
Answer: D
Question No : 30
22
Juniper JN0-347 : Practice Test
Referring to the exhibit, which path will traffic from R6 take to reach R1?
Answer: D
Question No : 31
Which LSA type describes the router ID of ASBR routers located in remote areas?
A. Type 4
B. Type 5
C. Type 3
D. Type 7
Answer: A
Question No : 32
23
Juniper JN0-347 : Practice Test
Referring to the exhibit, a packet tagged with vlan-id 34 arrives on interface xe-0/2/3.0 with
a source MAC that does not match an entry in the DHCP snooping database.
Answer: D
Explanation:
The interface specified in this group is trusted. DHCP snooping and DHCPv6 snooping do
not apply to the trusted interface. Likewise, DAI, IP source guard, IPv6 source guard, and
IPv6 neighbor discovery inspection—even if they are enabled for the VLAN—do not apply
to the interface that is configured with the overrides and the trusted options. Access
interfaces are untrusted by default.
https://www.juniper.net/documentation/en_US/junos/topics/reference/configuration-
statement/overrides-edit-vlans.html
24
Juniper JN0-347 : Practice Test
Question No : 33
What are three types of bridge protocol data units? (Choose three.)
Answer: B,C,E
Question No : 34
You manage the Layer 2 network shown in the exhibit. You experience a failure on the ge-
0/0/0 link between Switch-1 and Switch-2.
25
Juniper JN0-347 : Practice Test
Which statement is correct about the expected behavior?
A. Switch-3’s ge-0/0/2 port role and state will transition to designated and forwarding.
B. Switch-3’s ge-0/0/2 port role and state will remain asalternate and discarding.
C. Switch-3 will become the root bridge for the RSTP topology.
D. Switch-3 will remove the ge-0/0/2 interface from the RSTP topology.
Answer: A
Question No : 35
Answer: D
Question No : 36
Which three BGP attributes are well-known and mandatory? (Choose three.)
A. AS Path
B. Next Hop
C. MED
D. Local Preference
E. Origin
Answer: A,B,E
Question No : 37
You are currently defining a new OSPF area. The area must advertise external routes but
26
Juniper JN0-347 : Practice Test
should not receive external routes from another area.
A. stub
B. backbone
C. not-so-stubby
D. totally stubby
Answer: C
Question No : 38
A. Area 0.0.0.0
B. Area 1.1.1.1
C. Area 2.2.2.2
D. Area 3.3.3.3
Answer: A
Question No : 39
What are three components that populate the Ethernet switching table? (Choose three.)
Answer: A,C,E
Question No : 40
27
Juniper JN0-347 : Practice Test
Which two statements are true about nonstop bridging (NSB)? (Choose two.)
A. NSB does not require all participating Routing Engines to run the same version of the
Junos OS.
B. NSB can be enabled under theprotocols layer2-controlhierarchy.
C. NSB requires you to configure gracefulRouting Engine switchover (GRES).
D. NSB does not require you to configure graceful Routing Engine switchover (GRES).
Answer: B,C
Question No : 41
Answer: B
Explanation: To encapsulate a GRE packet in an IP packet, a GRE header and an outer
IP header are added. The GRE header and outer IP header add an additional 24 bytes of
overhead to the packet. The outer header includes the source IP address, the entry point of
the tunnel, and the destination IP address—the exit point of the tunnel. The inner packet
(also known as the payload packet) is not modified, except the time-to-live (TTL) field,
which is decremented. The TTL field must be decremented to ensure that the packet does
not live forever. GRE packets that are encapsulated in IP packets use IP protocol type 47
Question No : 42
What are two terminating actions of a Layer 2 firewall filter? (Choose two.)
28
Juniper JN0-347 : Practice Test
A. reject
B. accept
C. log
D. discard
Answer: B,D
Question No : 43
Answer: B,C
Explanation: Aggregate RoutesAggregate routes allow you to combine groups of routes
with common addresses into a single entry. By combining routes into a single entry, you
can decrease the number of route advertisements sent by your device, thus decreasing the
size of the routing tables maintained by neighboring devices. A second advantage of
advertising a single route prefix that represents all other internal route prefixes is that
internal routing instabilities can be hidden from external peers.
Question No : 44
You manage a Layer 2 network that spans two buildings. You are asked to ensure that all
traffic that traverses this connection between the two buildings is secured.
Which port security feature should be used to secure this Layer 2 traffic?
A. IP source guard
B. MACsec
29
Juniper JN0-347 : Practice Test
C. DHCP snooping
D. dynamic ARP inspection
Answer: B
Question No : 45
In this scenario, which two actions would solve this problem? (Choose two.)
A. Enable 802.1x.
B. Enable persistent MAC learning.
C. Enable dynamic ARP inspection.
D. Enable storm control.
Answer: A,B
Question No : 46
30
Juniper JN0-347 : Practice Test
Referring to the exhibit, which statement explains why the route to 192.168.178.0/24
advertised from 192.168.35.90 is hidden?
Answer: A
Question No : 47
31
Juniper JN0-347 : Practice Test
Answer: B
Explanation:
In this example, the qualified next hop 10.30.30.1 is assigned the preference 2, and the
next-hop 10.20.20.1 is assigned the preference 6. The routes with a lower route preference
are always used to route traffic.
https://www.juniper.net/documentation/en_US/junos/topics/concept/routing-protocol-static-
security-route-preference-and-qualified-next-hop-understanding.html
32
Juniper JN0-347 : Practice Test
Question No : 48
You are establishing a BGP session between R1 and R2. R2 shows 172.24.1.1 as its peer
address for R1 instead of 192.168.100.1.
Answer: D
Question No : 49
33
Juniper JN0-347 : Practice Test
Which device is used to separate collision domains?
A. switch
B. router
C. hub
D. firewall
Answer: A
Question No : 50
Which two OSPF LSA types will you see in a stub area? (Choose two.)
A. network (Type 2)
B. summary (Type 3)
C. ASBR summary (Type 4)
D. external (Type 5)
Answer: A,B
Question No : 51
What are two OSPF packet types that use multicast for communication on a multicast
segment? (Choose two.)
A. hello
B. link-state request
C. database description
D. link-state update
Answer: A,D
Question No : 52
34
Juniper JN0-347 : Practice Test
The configuration shown in the exhibit was committed on an EX Series switch. You are
notified that the phone using the voice VLAN does not work. You determine that voice
traffic is not passing through the local switch.
A. You should add the voice VLAN as a member on the ge-0/0/8.0 interface.
B. You should change the port mode on ge-0/0/9.0 totrunk.
C. You should add the voice VLAN as a member on the ge-0/0/9.0 interface.
D. You should change the voice VLAN ID to match the data VLAN ID.
Answer: A
Question No : 53
Which two statements are true about Virtual Chassis? (Choose two.)
35
Juniper JN0-347 : Practice Test
D. The member ID is not preserved through reboots.
Answer: A,C
Question No : 54
Which two statements describe the BGP Local Preference attribute? (Choose two.)
Answer: A,D
Question No : 55
Which two values are used to generate a bridge ID when using STP? (Choose two.)
Answer: A,B
Question No : 56
You received an alert from your monitoring system that the master Routing Engine (RE) on
an EX4300 switch in a virtual chassis has hardware issues and might need to be replaced.
Because the switch already had graceful Routing Engine switchover (GRES) enabled and
configured, you must perform a manual switchover to the backup RE to avoid disruption.
36
Juniper JN0-347 : Practice Test
A. Log in to the backup RE and issue therequest chassis-control operation command.
B. Log in to the backup RE and issue therequest chassis routing-engine master
switchoperation command.
C. Log in to the backup RE and issue therequest chassis routing-engine master
acquireoperation command.
D. Log in to the backup RE andissue therequest iccp-serviceoperation command.
Answer: B
Question No : 57
Referring to the exhibit, which two statement are true? (Choose two.)
A. The device will not form adjacencies with devices in a different area.
B. The Level 2 database will be empty.
C. The IS-IS protocol is disabled on the device.
D. The device will not have a Level 2 database.
Answer: A,B
Question No : 58
Which static route next-hop value indicated that the packet will be silently dropped?
37
Juniper JN0-347 : Practice Test
A. resolve
B. discard
C. reject
D. next-table
Answer: B
Question No : 59
38
Juniper JN0-347 : Practice Test
There are dynamically and statically routed networks attached to the ge-0/0/1 interface on
R1. You only want the dynamically learned routes to show up in routing tables for R2 and
R3, but the statically routed networks are also appearing. Those networks should only be
seen by the R1 device.
Answer: B
Question No : 60
39
Juniper JN0-347 : Practice Test
Answer: D
Question No : 61
40
Juniper JN0-347 : Practice Test
Answer: D
Question No : 62
41
Juniper JN0-347 : Practice Test
Referring to the exhibit, which two statements are true regarding IS-IS adjacencies?
(Choose two.)
Answer: A,B
Question No : 63
Which Junos feature allows you to combine multiple interfaces into a single bundle?
A. VRRP
B. Virtual Chassis
C. LAG
D. NSB
42
Juniper JN0-347 : Practice Test
Answer: C
Question No : 64
Referring to the exhibit, when using the default routing behavior, what happens to Packet A
and Packet B on R1?
Answer: B
Question No : 65
A. internal
B. external
C. multihop
43
Juniper JN0-347 : Practice Test
D. null
Answer: B
44