Documente Academic
Documente Profesional
Documente Cultură
1 Acknowledgement 2
2 Introduction 3
5 Crushing plant 7
6 Raw mill 12
7 Kilnsection 18
8 Electrostatic precipitator 22
11 Packaging plant 28
12 Quality control 29
13 Conclusion 30
Introduction
The origin of the DCM dates back to1889, when Delhi Cloth & General Mills was
established. Founded by Lala Sri Ram, DCM started its journey with the
incorporation of a public limited Company on March 26, 1889 in the name and style
of Delhi Cloth & General Mills Co. Limited under the provisions of Act VI of 1882.
Over the years, the DCM Group became one of India's largest conglomerates.
Consisting of a large number of Companies/Divisions, reputed for their product
quality, dynamism and business integrity along with their quick response to
changesinthe environment. It expanded and diversified its activities intoa number
ofmanufacturing activities such as Textiles, Sugar, Chemicals, Rayon, Tyre Cord,
Fertilizers, Information Technology and Engineering Products etc. The name of the
Company was changed on October 6, 1983 to DCMLimited.
One of the main reasons for the Group's success is its focusontechnologyand quality.
With the backing of its people, its technology and its alliances, the DCM Group is able
totackle any challenges that come itsway.
World over, the 80's was the decade of diversification. However, the 90's were a time
for consolidation and focusing on core business areas. The DCM Group, too, decided
to move out of those business ventures, which did not fit, into its overall strategic
vision. Its thrust is now on value-added products, on high technology sunriseindustries.
The business of the Company was reorganized with effect from 1.4.1990 under a
Scheme of Arrangement under section 391 / 394 of the Companies Act, 1956
approved by the shareholders, creditors and the financial institutions and sanctioned
by the Honorable High Court of Delhi at New Delhi in 1990. Under the said
reorganization, all units of the Company existing at that time stood vested and / or
continued to vest in terms of the said Scheme into four separate companies namely,
DCMLimited
DCM Shriram IndustriesLimited
DCM Shriram ConsolidatedLimited
NShriramIndustrial EnterprisesLimited
About DCM Shriram cement works
SCW is a wet process cement plant based on calcium hydroxide sludge of sister
calcium carbide plant, located in the same complex. SCW was commissioned in 1987
with the technical know- how from M/s. Lafarge CoppeeLavelin, France. Products of
the plant are OPC-53 grade, Shriram N irman (PPC) and Shriram Silver (PPC).
Besides these products, trading of POP is also carried out. The plant is certified for ISO
9001, 14001 and OHSAS 18001 for its effective Quality, Environment, and
Occupational Health and Safety Ma nagement Systems. It has also been awarded five
starcertificates by British Safety Council for its effective safetysystems.
Installed capacity of SCW is 4.0-lakh tons cement per annum.
Shriram cement is known for high quality for last several years. Following are the
major special properties:
Types of cement
Ordinary Portland cement(OPC)
Portland pozzolona cement(PPC)
Sulphate resistingcement
Rapid hardeningcement
Oil wellcement
Masonrycement
Portland blast furnace slagcement
Super Sulphatecement
High aluminacement
White gradecement
Quick settingcement
Hydrophobic cement
Silver grade cement
There are three processes of manufacturing cement which are known as the wet, dry,
and semidry processes and are so termed when the raw materials are ground wet and
fed to the kiln as a slurry, ground dry and fed as a dry powder, or ground dry and then
moistened to form manufacturing of cement.
Raw MaterialsExtraction
The limestone and clay occur together in quarries. It is necessary to drill and blast
these materials before they are loaded in trucks. The quarry trucks deliver the raw
materials to the crusher where the rock is crushed to smaller than 12mm. The raw
materials are then stored ready foruse.
Raw MaterialsPreparation
About 80% moisture contained slurry comes from carbide plant and acetylene plant,
which is the by-product of those plants. Adjusting the relative amount of limestone
and clay being used very carefully controls the chemical compositio n of the slurry.
The slurry is stored in large basins ready for use known as decanter and DP tanks and
then further fined by rawmill.
ClinkerBurning
The slurry is fed into theupper end of a rotary kiln, while at the lower end of the kiln; a
very intense flame is maintained by blowing in finely ground coal. The slurryslowly
moves down the kiln and is dried and heated until it reaches a temperature of almost
1500 degrees Celsius producing "clinker". This temperature completely changes the
limestone and clay to produce new minerals, which have the property of reacting with
water to form a cementitious binder. The hot clinker is used to preheatthe air for burning
the coal, and the cooled clinker is stored ready foruse.
CementMilling
The clinker is finely ground with about 5% gypsum in another mill, producingcement.
(The gypsum regulates the early setting characteristic of cement). The finishedcement
is stored in silos then carted to our wharf or packing plantfacilities.
CrushingPlant
| 6
The crushing plant receives limestone from mines and in two stages operation crushes
it into size of 12mm. there are two crushers, primary crusher of L&T (double toggle
jaw crusher) and secondary crusher of Economer (Hammer crusher). Crushers have
capacity of 100 ton per hour and are driven by 132 KW motors. The crushedlimestone
is stored in yard of 2miles.
The limestone from Bundi and Ramganjmandi comes into plant in loadedtrucks and
isunloaded here in the chambers having rectangular sections .The capacity of
Unloading Hopper is 60 Metricton.
Apronfeeder:
Apron feeders were designed for uniform and regulated feed of loose and lump
materials from feed bin to crushing aggregates and transporters of different types. The
transporting cloth of apron feeders is a closed circuit, consisting of plates, which are
connected hingedly. The productivity of feeders is regulated at the expense of cloth
speed changing and size of bin outlet. The transporting cloth is activated with drive
sprocket; direction and chain supporting are implemented with the shaped rolls. To
regulate the cloth tension the screw mechanism of back sprocket movement is used.
| 7
JawCrusher:
Jaw crusher is also named jaw breakers, rock crusher, or rock breaker. Jaw crusher is
mainly used to primarily and secondarily crush many kinds of mining rocks, and the
highest anti-pressure strength of crushed material is 320Mpa.
Features of JawCrusher:
Structure of JawCrusher:
The structure of jaw crusher: main frame, eccentric shaft, a large belt pulley, fly
wheel, swing jaw, side guard plate, toggle plate, Rear bracket, adjust gap
screw, reset spring, and fixed jaw and swing jaw board etc., and the toggle
plate also plays a role of protection. The length of toggle is 898 mm (movable
jaw) and 790 mm (fixed jaw).
| 8
Working Principle of JawCrusher:
The motor drives the movable jaw plate to do periodic motion towards the fixed aw
plate by the eccentric shaft.
The angle between toggle plateand movable jaw plate increases whenmovable
jaw plate moves. Sothe movable jaw plate moves towards thefixed
jaw plate.
The material between the movable jaw plate and fixed jaw plate will be
crushed in this process. The angle between toggle plate and movable jaw plate
decreaseswhen
Movable jaw plate moves down, the movable jaw plate move leaves fixed jaw plate
by pulling rod and spring, the final crushed material will be discharged from the
outlet.
Hammercrusher:
Figure 5
| 9
The materials collisions with each other at the same time, after repeatedly broken, the
materials less than sieve article eduction from the gap. Individual larger
materialsimpact by the hammerhead again, grinding, extrusion and broken. At last,
deduction from the gap. Thusobtaining products with required size. It is made by
manganese steel.
Working principle
The main working part of the Crusher is the rotor with hammer rings. The rotor is
consisted of hammer ring shaft and the ring hammer, etc. The rotor driven by motor
rotates at a high speed in the crushing chamber. The materials are conveyed into the
chamber from the top inlet, then impact by the high-speed rotating hammer ring, thus
crashed, squeezed ground among the materials and finally achieved the goal of
crushing. At the bottom of the rotor, there are grate plate equipped, the crushed
materials which smaller than the grate hole size can be discharged through the grate
plate, while the larger ones will be crushed by the hammer ring till the required size
and bedischarged.
VibratingscreenorDSMscreen
The function of DSM (Dynamic screen manager) screen is to only pass the particles
with size of not more than 12mm. It consists of vibration damper of 6-12 mm. The
rejected particles are again feed into crusher and the remaining is sent to the yard via
belts. Before coming to screen the particles are moved below the magnetic separator
so that all particles with magnetic properties shall be kept aside from the process. After
the screen there is placed a dustcollector.
The stored limestone is reclaimed is from yard by the help of reclaimer. This
equipment is supplied by space age limited. Its capacity is 100 ton per hour. The
reclaimer shaves one side of the pile in such manner that further blending ofLimestone
occurs. The reclaimed limestone is conveyed to the raw millthrough belts.
Raw Mill
|
1
0
A Raw mill section used to grind raw materials into " rawmix" during the
manufacture of cement. Rawmix is then fed to a cement kiln, which transforms it into
Clinker, which is then ground to make cement in the cement mill. The raw
millingstage of the process effectively de fines the chemistry (and therefore physical
properties) of the finished cement, and has a large effect upon the efficiency of the
whole manufacturingprocess.
|
1
1
Decanterand DP Tank
Figure 9: DPTanks
Figure 10:Decanter
Feeder
The feeder is a ferries wheel driven by a variable DC drive. There are three hoppers in
a raw mill building .one for the limestone received from the yardafter proper blending,
second for high grade limestone used sometimes to improve the limestone content to
the burn ability or melting characteristics of raw mix the clinkerizationsection.
Rawmill
Layout
A Raw/Ball mill is a horizontal cylinder partly filled with steel balls (or occasionally
other shapes) that rotates on its axis, imparting a tumbling and cascading action to the
balls. Material fed through the mill is crushed by impact and ground by attrition
between the balls. The grinding media are usually made of high-chromium steel. The
smaller grades are occasionally cylindrical ("pebs") rather than spherical. There exists
a speed of rotation (the "critical speed") at which the contents of the mill would
simply ride over the roof of the mill due to centrifugal action. The critical speed (rpm)
is given by: nC= 42.29/√ d, where d is the internal diameter in meters. Ball mills are
normally operated at around 75% of critical speed, so a mill with diameter 5 meters
will turn at around 14rpm.
The mill is usually divided into at least two cha mbers,(Depends upon feed input size
presently mill installed with Roller Press are mostly single chambered), allowing the
use of different sizes of grinding media. Large balls are used at the inlet, to crush
clinker nodules or limestone (which can be over 25 mm in diameter). Ball diameter
here is in the range 60–80 mm. In a two-chamber mill, the media in the second
chamber are typically in the range 15–40 mm, although media down to 5 mm are
sometimes encountered. As a general rule, the size of media has to match the size of
material being ground: large media can't produce the ultra-fine particles required inthe
finished cement, but small media can't break large clinkerparticles.
A current of air is passed through the mill. This helps keep the mill cool, a nd sweeps
out evaporated moisture, which would otherwise cause hydration and disrupt material
flow. The dusty exhaust air is cleaned, usually with bag filters.
A Raw mill is driven by 750 KW motor that rotates the mill at 17 rpm. The length of
mill is 13 m and diameter is 2.25 m. Both the compartments of mill are filled with
grinding media apart from sludge and limestone. in first compartment high steel balls
are put which are responsible for coarse grinding.
The second compartment contains balls o f high chromium steel, which are
responsible for grinding limestone and iron. About 36 % of compartment is filled with
theseballs.
50 20
40 10
30 6
DSMScreen
The raw mill outlet slurry goes to war man pump, which pumps the slurry to DSM
Screen. Here the fine particles passé through the drum filters and goes to slurry mixer.
The coarse particle goes back to the mill to further grinding.
Slurry mixertank
The slurry mixer is 12.5 m diameter tanks having arms on which air nozzles are fixed.
Compressed air through these nozzles about 1.5 kg/cm3 agitates the slurry and
prevents it from becoming solid. From here the slurry is feed into kiln by slurry
pumps.
Kiln Section
A Rotary kiln is a pyro processing device used to raise materials to a high temperature
(calcination) in a continuous process. The basic components of a rotary kiln are the
shell, the refractory lining, support Tyres and rollers, drive gear and internal heat
exchangers.
KilnShell
This is made from rolled mild steel plate, usually between 15 and 30 mmthick, welded
to form a cylinder, which may be up to 230 m in length and up to 6 m indiameter. This
will be usually situated on an east/west axis to prevent eddy currents. Upper limits on
diameter are set by the tendency of the shell to deform under its own weight to an oval
cross section, with consequent flexure during rotation. Length is not necessarily
limited, but it becomes difficult to cope with changes in length on heating and cooling
(typically around 0.1 to 0.5% of the length) if the kiln is very long.
RefractoryLining
The purpose of the refractory liningis toinsulate the steel shell from the high
temperatures inside the kiln, and to protect it from the corrosive properties of the
process material. It may consist of refractory bricks or cast refractory concrete, ormay
be absent in zones of the kiln that are below around 250°C. The refractory selected
depends upon the temperature inside the kiln and the chemical nature of the material
being processed. In cement, maintaining a coating of the processed material on the
refractory surface prolongs the refractory life . The thickness of the lining is generally
inthe range 80 to300 mm. A typical refractory will becapable of
maintaining a temperature drop of 1000°C or more between its hot and cold faces.
The shell temperature needs to be maintained below around 350°C in order to protect
the steel from damage, and continuous infrared scanners are used togive earlywarning
of "hot-spots" indicative of refractoryfailure.
Tyres andRollers
Tyres, sometimes called riding rings, usually consist of a single annular steel casting,
machined to a smooth cylindrical surface, which attach loosely to the kiln shell
through a variety of "chair" arrangements. These require some ingenuity of design,
since the Tyremust fit the shell snugly, but also allow thermal movement. The
Tyrerides on pairs of steel rollers, also machined to a smooth cylindrical surface, and
set about half a kiln-diameter apart. The rollers must support the kiln, and allow
rotation that is as nearly frictionless as possible. A well-engineered kiln, when the
power is cut off, will swing pendulum- like many times before coming to rest. The
mass ofa typical 6 x 60 m kiln, including refractories and feed, is around 1100 tones,
and would be carried on three Tyres and sets of rollers, spaced along the length of the
k iln. The longest kilns may have 8 sets of rollers, while very short kilns may have
only two. Kilns usually rotate at 0.5 to 2 rpm, but sometimes as fast as 5 rpm. The K
ilnsof most modern cement plants are running at 4 to 5 rpm. The bearings of the
rollers must be capable of withstanding the large static and live loads involved,
andmust be carefully protected from the heat of the kiln and the ingress of dust. In
addition to support rollers, there are usually upper and lower "retaining (or thrust)
rollers" bearing against the side of Tyres, that prevent the kiln from slipping off the
supportrollers.
DriveGear
The kiln is usually turned by means of a single Girth Gear surrounding a cooler part
of the kiln tube, but sometimes driven rollers turn it. The gear is connected through a
gear train to a variable-speed electric motor. This must have high starting torque in
order tostart the kiln with a large eccentric load. A 6 x 60 m kiln requires around 800
kW to turn at 3 rpm. The speed of material flow through the kiln is proportional
torotation speed, and so a variable speed drive is needed in order tocontrol this. When
driving through rollers, hydraulic drives may be used. These have the advantage of
developing extremely high torque. In many processes, it is dangerous to allow a ho
and bottom of the kiln may cause the kiln to warp, and refractory is damaged. It
istherefore normal to provide an auxiliary drive for use during power cuts. This may
be a small electric motor with an independent power supply, or a diesel engine. This
turns the kiln very slowly, but enough to preventdamage.
Internal heatexchangers
Otherequipment
The kiln connects with a material exit hood at the lower end and to ducts for waste
gases. This requires gas-tight seals at either end of the kiln. The exhaust gasmay go to
waste, or may enter a preheater which further exchanges heat with the entering feed.
The gases must be drawn through the kiln, and the preheater if fitted, by a fan situated
at the exhaust end. In preheater installations, which may have a high pressure-drop, a
lot of fan power may be needed, and the fan isoften then largest drive in the kiln
system. Exhaust gases contain dust and there may be undesirable constituents such as
sulfur dioxide or hydrogen chloride. Equipment is installed to scrub these out before the
exhaust gases pass to atmosphere, calledESP.
Thermalefficiency
Principle of Operation
The kiln is a cylindrical vessel, inclined slightly to the horizontal, which is rotated
slowly about its axis. The material to be processed is fed into the upper end of the
cylinder. As the kiln rotates, material gradually moves down towards the lower end,
and may undergo a certain amount of stirring and mixing. Hot gases pass along the
kiln, sometimes in the same direction as the process material (co-current), but usually
in the opposite direction (counter-current). The hot gases may be generated in an
external furnace, ormay be generated by a flame inside the kiln. Such a flame is
projected from a burner-pipe (or "firing pipe"), which acts like a large Bunsen burner.
The fuel for this may be gas, oil, pulverized petroleum coke or pulverizedcoal.
Here, at DCM SCW the kiln is 120 m long, it has a diameter of 3.75 m. it islonger than
usual because it’s a wet process and additional chain zone required to bring the
moisture down. The chain zone is about 23.75 m in length. The speed of kiln isvaried
by a D.C drive. K ilnis coal fired and the flue gases travel up the kiln. These fluegases
then passes through the ESP (electrostatic precipitator) where dust is collected and
cleaned flue gases are pulled out of the system by an I.D fan which is again driven by
a variable speed motor. The dust is again put into the decanter from where it goes again
to the normal procedures of rawpreparation
As the raw mix travel down the kiln it follows the helical path from chain zone. After
chain zone comes the preheating zonewhere the raw mix components are heated up to
the calcination temperature. A calcination zone where the raw mix gets calcinated
follows this. CO2 released .the calcination zone terminates into burning zone where
heat released through coal burning melt the oxide an bring them to react toclinker
.thefine coal, which is used to create the flame is provided by coal mill. The lengthand
temperature of various zone in kiln vary with the firing rate, feed rate and the I.D fan
speed .the burning zone temperature is1250°C-1400°C
Temperatures Reactions
180c Evaporation of water
500c and above Evolution of combined gases
900c and above Clinkerization and dehydration
1200c Production of clay and production ofCO2
1200c and above Reaction between clay and lime and thus forms the
cement compound
Electrostatic precipitator (ESP)
An electrostatic precipitator (ESP) is a filtration device that removes fine
particles, like dust and smoke, from a flowing gas using the force of an induced
electrostatic charge minimally impeding the flow of gases through the unit. In contrast
to wet scrubbers, which apply energy directly to the flowing fluid medium, an ESP
applies energy only to the particulate matter being collected and therefore is very
efficient inits consumption of energy (in the form ofelectricity).
The most basic precipitator contains a row of thin vertical wires, andfollowed by a
stack of large flat metal plates oriented vertically, with the plates typically spaced
about 1 cm to 18 cm apart, depending on the application. The air or gas stream flows
horizontally through the spaces between the wires, and then passes through the stack
of plates. A negative voltage of several thousand volts is applied between wire and
plate. If the applied voltage is high enough, an electric corona discharge ionizes the
gas around the electrodes. Negative ions flow to the plates and charge the gas- flow
particles. The ionized particles, following the negative electric field created by the
power supply, move to the grounded plates. Particles build up on the collection plates
and form a layer. The layer does not collapse, thanks to electrostatic pressure (due to
layer resistivity, electric field, and current flowing in the collectedlayer).
Collectionefficiency
1) Electrical resistivity;and
2) Particle sizedistribution.
These properties can be measured economically and accurately in the laboratory, using
standard tests. Resistivity can be determined as a function of temperature in
accordance with IEEE Standard 548. This test is conducted in a n air environment
containing a specified moisture concentration. The test is run as a function of
ascending or descending temperature, or both. Data is acquired using an average ash
layer [further explanation needed] electric field of 4 kV/cm. Since relatively low
applied voltage is used and no sulfuric acid vapor is presentin the test environment, the
values obtained indicate the maximum ashresistivity.
In an ESP, where particle charging and discharging are key functions, resistivity is an
important factor that significantly affects collection efficiency. While resistivity is an
important phenomenon in the inter-electrode region where most particle chargingtakes
place, it has a particularly important effect on the dust layer at the collection electrode
where discharging occurs. Particles that exhibit high resistivity are difficult to charge.
But once charged, they do not readily give up their acquired charge on arrival at the
collection electrode. O nthe other hand, particles with low resistivity easily become
charged and readily release their charge to the grounded collection plate. Both
extremes in resistivity impede the efficient functioning of ESPs. ESPs work best under
normal resistivityconditions.
Advantages ofESP
High collectionefficiency.
Low resistance path for gasflow
Treatment of large amount of gases and at hightemperature
Ability of coping with corrosiveatmosphere
Clinker cooler and coal section
The clinker due to rotary of the kiln gets discharged into the grate cooler where
clinker is cooled. There are four sections of grate cooler. in first section ,moving
clinker bed is cooled with the fresh air is forced through the grate cooler fan no.1 . In
second and third section, the clinker is cooled with the help of circulation air through
fan no. 2&3. Finallythe cooled clinker is about 100c. This is then feed into VSI
crusherwhere it is broken into small pieces. From here small pieces are fed into the drag
chain, which fall onto the deep where it is stored into the cementsilos.
VSI crushers use a different approach involving a high-speed rotor with wear resistant
tips and a crushing chamber designed to 'throw' the rock against. The VSI crushers
utilize velocity rather than surface force as the predominant force to break clinker.
Applying surface force (pressure) results in unpredictable and typically non-cubical
resulting particles. Utilizing velocity rather than surface force allows the breaking
force to be applied evenly both across the surface of theclinker.
VSI crushers generally utilize a high speed-spinning rotor at the center of the crushing
chamber and an outer impact surface of either abrasive resistant metal anvils or
crushed rock. Utilizing cast metal surfaces 'anvils' is traditionally referred to as a"Shoe
and AnvilVSI".
Figure 18:VS I
CementSilos
Cement silos are on-site storage containers used for the storage and distribution of
various types of cement mixtures. A cement silo can be a permanent structure, or a
portable model that can be relocated when necessary. The cement silo usually is
equipped with some type of blower to help expel the stored contents into a truck or
other receptacle.
A cement storage silo can be structured to hold no more than a few tons of dry cement
products, or be designed to efficiently hold several hundred tons. Generally, larger
silos are permanent structures that cannot be moved. It is used, where the finished
product is stored until it is time for shipment. Many building sites that utilize concrete
in the construction process opt for portable cement silos that can be moved around the
site as the need arises.
It is not unusual for construction companies to keep several portable cement silos
available for different building projects. These simple storage devices can usually be
set up in a matter of hours, and then dismantled once the project is complete. Storage
ofthe portable cement silo is relatively easy, since the components can be stored in a
Warehouse until the device is needed at another buildingsite.
Both the permanent and the portable cement silo are usually equipped with some type
of blower. The blower makes it easier to expel the product from the silo. Blowers are
often driven by electricity, although there are models that rely on propane or even
gasoline. Blower equipment with the portable silos takes very little time to set up, and
can also be stored easily when not in use.
It is important to note that the materials and the design of a cement silo will vary,
depending on the type of cement product that is to be stored in the facility. Not all
types of building materials are conduciveto keeping all ofthe various components that
go into cement blends from caking or absorbing moisture. For example, a silothat is
structured to protect the integrity of soda ash may not work as well with lime. Along
with the ingredients of the concrete, the configuration of the cement silo will
beslightly different for products that are identified as high performance concrete or
self-compactingconcrete.
There are two cement silos, one for POC and other one for PPC and one steel silo for
steel grade cement. The cement silos have a capacity of 3500 metric ton each and
steel silo is having 700 metric toncapacity.
Clinker from the silos is extracted from the bottom through three vibrofeeders installed
in each silos. The clinker belt with a constant speed feed the clinker into cementmill.
For OPC, gypsum is added and for PPC, pozzolonais added. The feeding of cement
mill is done through weight feeder. Gypsum from yard is fed into a hopper through a
conveyer belt into pozzolona bins by diverting the material with the help of
hydraulically operated diverter. Here, the ball mill is filled with grinding media
varying from 100mm-150mm sizes in first chamber and in second compartment
cylindrical pebbles clypeus of20mm-25mm.
Materialsground
Portland clinker is the main constituent of most cement. In Portland cement, a little
calcium sulfate (typically 3-10%) is added in order toretard the hydration of tricalcium
aluminate. The calcium sulfate may consist of natural gypsum, anhydrite, or synthetic
wastes such as flue-gas desulfurization gypsum. In addition, up to 5% calcium
carbonate and up to 1% of other minerals may beadded.
It is normal to add a certain amount of water, and small quantities of organic grinding
aids and performance enhancers. "Blended cements" and Masonry cements may
include large additions (up to 40%) of natural pozzolans, fly ash, limestone, silicafume
or metakaolin. Blast furnace slag cement may include up to 70% ground granulated
blast furnaceslag.
Temperaturecontrol
Heat generated in the grinding process causes gypsum (CaSO4 .2H 2O) to lose water,
forming bassanite (CaSO4 .0.2-0.7H 2 O) or γ-anhydrite (CaSO4. ~0.05H2O). The
latter minerals are rapidly soluble, and about 2% of these in cement is needed to
control tricalcium aluminate hydration. If more than this amount forms, crystallization
ofgypsumon theirre-hydrationcauses"falseset"-asuddenthickeningofthecement mix a
few minutes after mixing, which thins out onre-mixing.High milling temperature causes
this. On the other hand, if milling temperature is too low, insufficient rapidly soluble
sulfate is available and this causes "flash set" - an
irreversible stiffening of the mix. Obtaining the optimum amount of rapidly soluble
sulfate requires milling with a mill exit temperature within a few degrees of 115 °C.
Where the milling system is too hot, some manufacturers use 2.5% gypsum and the
remaining calcium sulfate as natural α-anhydrite (CaSO4).
Complete dehydration of this mixture yields the optimum 2% γ-anhydrite. In the case
of some efficient modern mills, insufficient heat is generated. This is corrected by
recirculating part of the hot exhaust air to the mill inlet.
Packagingplant
Packing of cement is done by L&T rotatory packing machine .the cement is extracted
from the selected silos and through slides; cement is taken into bucket elevator and
subsequently to the hopper just above the packer. There are two packing machines for
the emergency case.
The main measure of fineness today is specific surface. Because cement particles
react with water at their surface, the specific surface area is directly related to the
cement's initial reactivity. By adjusting the fineness of grind, the manufacture can
produce a range of products from a single clinker. Tight control of fineness is
necessary inorder toobtain cement with the desired consistent day-to-day
performance, so round-the-clock measurements are made on the cement as it is
produced, and mill feed-rates and separator settings are adjusted to maintain constant
specificsurface.
In addition to fineness, added materials in the cement must be controlled. In the case of
gypsum addition, the material used is frequently of variable quality, and itis normal
practice to measure the sulfate content of the cement regularly, typically by x- ray
fluorescence, using the results to adjust the gypsum feed rate. Again, this process is
often completely automated. Similar measurement and control protocols are applied to
other materials added, such as limestone, slag and flyash.
Conclusion
The practical training has proved to be quite fruitful .It provided me to encounter with
such huge machines and mechanisms. It has allowed me an opportunity to get an
exposure of practical aspects and their implementation to theoretical fundamentals.
I became Familiarize with the practical engineering work in various disciplines and
methods of engineering practice. This will help me improving my performance in
theory classes by introducing to the practical work. It helped me to know my strengths
and weaknesses so that I can improve my skills and overcome my limitations by
taking appropriate measures I was exposed to real work situations and I learned how to
equip them with the necessary skills so that I would be ready for the job when I’ll
begraduated.
The architecture of the plant, the way various units are linked, the way of working in
plant and how everything is controlled make me realize that engineering is not just
learning the structured description and working of various machines but the greater
part of planning management