Documente Academic
Documente Profesional
Documente Cultură
1 из 18
01-136
01-137
Test requirements
CAUTION!
01-138
The socket number designations on the VAG 1598 test box are identical to the terminal
designations on the ABS control module -J104- Electrical Wiring Diagrams,
Troubleshooting and Component Locations binder.
If the measured values deviate from the specifications, repair the malfunction as described
in the right-hand column of the table Electrical Wiring Diagrams, Troubleshooting and
Component Locations binder.
Conduct continuity checks with VW 1594 connector test kit (used for bridging
terminals/sockets).
If the measured values deviate only slightly from the specifications, clean sockets and
connectors for tester and adapter cables (with contact spray G 000 700 04 ) and repeat the
test.
Before replacing components, check wiring and connections and also, particularly for
specifications of less than 10 , repeat the resistance test on the component.
Teves 20 GI ABS and ABS/EDL electrical test Стр. 4 из 18
01-139
01-140
01-141
- Check resistance of
ABS wheel speed
sensor (1.0 - 1.3 k )
- Check resistance of
ABS wheel speed
sensor (1.0 - 1.3 k )
01-142
- Check resistance of
ABS wheel speed
sensor (1.0 - 1.3 k )
- Check resistance of
ABS wheel speed
sensor (1.0 - 1.3 k )
01-143
Ignition
switched off
Min. 65 mV
- Rotate right - Check whether ABS
alternating
front wheel at wheel speed sensor has
voltage
approx. 1 been interchanged.
rev./sec. Read measuring value
block, Page 01-112
10 4 + 11 Left front Vehicle - Check installation of
ABS wheel raised ABS wheel speed
speed sensor and impulse rotor
sensor -
G47- voltage
signal
Ignition
switched off
Min. 65 mV
- Rotate left front - Check whether ABS
alternating
wheel at approx. wheel speed sensor has
voltage
1 rev./sec. been interchanged.
Reading measured
value Page 01-112
Teves 20 GI ABS and ABS/EDL electrical test Стр. 9 из 18
01-144
Ignition
switched off
190 mV to
- Rotate right - Check whether ABS
1140 mV
rear wheel at wheel speed sensor has
approx. 1 been interchanged. Read
rev./sec. measuring value block,
Page 01-112
12 2 + 10 Left rear Vehicle - Check installation of
ABS wheel raised ABS wheel speed sensor
speed and impulse rotor
sensor -G46-
voltage
signal
Ignition
switched off
190 mV to
- Rotate left rear - Check whether ABS
1140 mV
wheel at approx. wheel speed sensor has
1 rev./sec. been interchanged. Read
measuring value block,
Page 01-112
13 15 + 21 Coding 0.0 -1.0
Ignition - Check wire and wiring
bridge switched off connections in harness
connector
- Replace if value
deviates from
specifications
Teves 20 GI ABS and ABS/EDL electrical test Стр. 10 из 18
01-145
Switch to voltage measuring range - 20 V for test step 14, Resistance measurement -
200 for test step 15
Test VAG Test of Specified Repairing
Test conditions
step 1598/21 value malfunction
sockets - Additional operations
14 - Voltage supply - Connect multimeter - Check wire
for VAG 1551
(Fluke 83/equivalent) to from T16/4 to
scan tool, data T16 (black) using adapter Ground (GND)
link connector cables from VW 1594
T16 - Check wire
connector test kit
from T16/16
via -S22- to
terminal 30
10.0 -
Terminal 41): Ground 14.5 V
01-146
01-147
Removing:
CAUTION!
- Disconnect battery.
01-148
Installing:
CAUTION!
01-149
Tightening torques
01-150
Note:
01-151
01-152
01-153
Note: