Documente Academic
Documente Profesional
Documente Cultură
Technical Education
Range Hoods
• Removing Control Switches
• Removing Blower Motor
• Wiring Diagrams
KitchenAid
Jenn-Air
Whirlpool
Prepared by: WHIRLPOOL CONSUMER CARE
WHIRLPOOL CORPORATION assumes no responsibility for any repairs made on our products by anyone other
than authorized In-Home Service Professionals.
®Registered trademark of Whirlpool, U.S.A., KitchenAid, U.S.A., Jenn-Air, U.S.A., or Maytag Corporation or its related companies.
®MAGIC CHEF is a registered trademark of CNA International, used under license.
© 2011 All rights reserved.
i
CONTENTS Page
GOALS AND OBJECTIVES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .i
SAFETY FIRST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii
RANGE HOODS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
GXW7330DX, GXW7336DX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
GXW7330DX, GXW7336DX WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
JXI5030WS, JXI5036WS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
JXI5030WS, JXI5036WS WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
JXW9030WS, JXW9048WS, JXW9036WS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
JXW9030WS, JXW9048WS, JXW9036WS WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
KXI2536YSS, KXW2530YSS, KXW2548YSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
KXI2536YSS WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
KXU4236YSS, KXU4230YSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
KXU4236YSS, KXU4230YSS WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
KXU8030YSS, KXU8036YSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
KXU8030YSS, KXU8036YSS WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
KXW2336YSS, KXW2330YSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
KXW2336YSS, KXW2330YSS WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
KXI4336YSS, KXI4342YSS, KXW4336YSS, KXW4330YSS, KXW4436YSS, KXW4430YSS . . . . . . . . . . . . 20
KXI4336YSS, KXI4342YSS, KXW4336YSS, KXW4330YSS, KXW4436YSS, KXW4430YSS WIRING DIAGRAM . 22
KXW8730YSS, KXW8736YSS, KXW8748YSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
KXW8730YSS, KXW8736YSS, KXW8748YSS WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
KXI9736YSS, KXI9748YSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
KXI9736YSS, KXI9748YSS WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
IN-LINE, INTERNAL AND EXTERNAL BLOWER SYSTEMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
INTERNAL BLOWER SYSTEMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
UXB0600D, UXB1200D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
IN-LINE BLOWER SYSTEMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
UXI0600D, UXI1200D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
EXTERNAL BLOWER SYSTEMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
KPEU722M, KPEC922M . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
KPEU722M, KPEC922M WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
ADDITIONAL RANGE HOOD WIRING DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
JXI8042W, JXI8036W, JXI8242W, JXI8236W Jenn-Air . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
JXW5030WS, JXW5036WS Jenn-Air . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
JXW6030W, JXW6036W Jenn-Air . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
JXW8030W, JXW8036W, JXW8042W Jenn-Air . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
JXW8230W, JXW8236W Jenn-Air . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
JXW8836W Jenn-Air . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
JXW9030WS, JXW9036WS, JXW9048WS Jenn-Air . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
KXI9736Y, KXI9748Y . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
KXU2830Y KitchenAid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
KXI2536Y, KXI2536Y KitchenAid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
UXL6048YSS,UXL6036YSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
UXG7360VD, UVG73660VD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
iii
SAFETY FIRST
Federal regulations and Standards can be found on the United States Government EPA Web Site. State Regulations and Standards and
licensing requirements, in most cases, can be found on the State Government Web Site .
iii
ii
GXW7330DXS, GXW7336DX
Whirlpool Control
Filters
Figure 1
To remove the control:
1. Disconnect power to the range hood.
2. Remove the filters.
3. Remove (2) T10 Torx screws screws screws from Figure 4 Figure 5
the under side of the frame at the right corner
of the hood, see figure 1.
4. Pull the metal control housing out through the
filter opening, see figure 2.
Figure 6
8. Remove cover to access wire
connections, see figure 6.
Figure 2
1
GXW7330DXS, GXW7336DX (continued)
Wiring Diagram
WIRING DIAGRAM
Junction box
L GNDN SE11PA
R
Y-G
BK
Ballast
W
BU
BU
W
BK
EMI
Filter
W
BK
Y-G
BK
BK
BK 15uF
Y-G
W
25uF
W
Motor Resistance
(Ohms) GY
BR
BK
16uF
Blue - Black 51.6
W
GY
BR
BK
R
Y
Y-G
Motor
Characteristics
Power Supply 120 VAC
BK
BU
R
Y-G
Frequency 60 HZ
Current 1.2A
Harness Connector
LCD Display
LCD Display
with Bracket
Figure 3
To remove the motor:
1. Disconnect power to the range hood.
Electrical Shock Hazard 2. Remove the range hood from the installation.
Disconnect power before servicing. 3. Remove the glass. See figure 1.
Replace all parts and panels before operating. 4. Remove the foam insulation from around the top
Failure to do so can result in death or of the range hood flue. See figure 4.
electrical shock.
Foam Insulation Vent Hood Top
Glass
Flue
Remove
These
Screws Figure 4
Glass
Retainer 5. Remove two (2) thumb screws to release intake
Bracket cover at the bottom of the unit. See figure 5.
Figure 1
6. Remove filter. See figure 5.
3. Remove four (4) T10 Torx screws that secure the Filter
Intake Cover
two (2) glass retainer brackets.
4. Remove two (2) T10 Torx screws from control
bracket. See figure 2.
Remove
These
Screws
Foam Insulation
T20 Torx
Figure 6 Figure 8
7. Remove (4) T10 Torx screws one in each corner
of the filter guard, see figure 6.
Figure 7 Figure 9
9. Loosen or remove (2) T20 Torx screws (one on
8. Remove (4) T10 Torx screws from the motor each side) that mounts the motor into “key
mounting plate, see figure 7. hole” slots at the top of the range hood, see
figure 8 and 9.
NOTE: It is recommended that an extention be used
with the screw driver because these screws NOTE: The “key hole” screws are covered by a piece
are difficult to reach. Screws also may be of foam insulation. Be sure to replace the
obstructed by insulation. insulation when reassembling.
If this is the case, move the insulation out of
the way and replace it when reassembling. 10.Position the motor so that the screw heads
clear the “key hole”slots and remove the motor.
Figure 10
4
JXI5042WS, JXI5036WS (continued)
Jenn-Air
Wiring Diagram
WIRING DIAGRAM
WIRING BOX
Electronic User Interface
L N
CON2
Y-G
Y-G
BK
N L NL NM LA S3 S2 S1
TRANSFORMER
P1 P2 P4A P3 P4 P5 P8 P7 P6
5 4 3 2 1 6 5 4 3 2 1 CON4
CON3
SEC
PRI
BR
BR
GY
BU
BK
W
R
R
R
BR
Y
ATTENTION!:
WITH 4 LAMPS
BU
GY
BK
R
W
SEC
Y-G
TRANSFORMER
Y
PRI
BR
Y
R 1
Y
BR
W
GY
R
BK
Y-G
BU
Y-G
Y
Y Y
BR
Y Y
Front Panel
(Hologen Lights)
Figure 2
NOTE: Be sure to note the position of the locator
pins on each switch and orient the switches
properly when reassembling,
see figure 2 and 3.
To remove switches:
1. Disconnect power to the range hood.
2. Remove the air filters
3. Remove (2) T10 Torx screws from the
underside of the front panel. This
is the panel that accommodates
the incandescent lights see figure 1.
Figure 1
6
JXW9030WS, JXW9048WS, JXW9036WS
Jenn-Air
Wiring Diagram
WIRING DIAGRAM
WIRING BOX
Electronic User Interface
L N
CON2
Y-G
Y-G
BK
N L NL NM LA S3 S2 S1
TRANSFORMER
P1 P2 P4A P3 P4 P5 P8 P7 P6
5 4 3 2 1 6 5 4 3 2 1 CON4
CON3
SEC
PRI
BR
BR
GY
BU
BK
W
R
R
R
BR
Y
ATTENTION!:
WITH 4 LAMPS
BU
GY
BK
R
W
SEC
Y-G
TRANSFORMER
Y
PRI
BR
Y
R 1
Y
BR
W
GY
R
BK
Y-G
BU
Y-G
Y
Y Y
BR
Y Y
Screws
Filter Control
Figure 2
7. Disconnect harness and remove
control, see figure 3.
Glass
Figure 1
8
KXI2530YSS, KXW2536YSS, KXW2548YSS (continued)
Kitchen Aid
To remove motor:
1. Disconnect power to the range hood.
2. Remove the filters.
3. Disconnect the harness.
4. Remove (4) 1/4” screws from
the motor mounting bracket,
see figure 1.
Motor
Motor Connector
Screws
Figure 1
NOTE: It is recommended that a screwdriver
extension be used because these screws
are difficult to reach.
9
KXI2530YSS, KXW2536YSS, KXW2548YSS (continued)
Kitchen Aid
Wiring Diagram
WIRING DIAGRAM
L GND N
BR BK (Line)
BU BU (Neutral) AGC 02125
Y/G
Y Y (Lamp)
BK
W Mechanical Push
W W (Speed 1) Buttons With Back Light
R R (Speed 2)
EMI BK GY (Speed 3) Switch Operation
Filter
Position Connection
BK
Off No Connection
Black - Yellow
Lamps
(1 - 3)
Y
Black - White
BU Low Speed
(1 - 4)
Black - Red
Medium Speed
Y/G
BK
BR
(1 - 5)
BU
BK
W
R
Y
Black - Gray
High Speed
(1 - 6)
Y/G
BK
12.5uF
W
R
BU
BU
Y
Y/G
BR
BU
BK
W
R
Y
1 2 3 4 5 6 7 8 9
Y/G
BR
GY
BU
BK
Y
R
BU
Y
Y
Y
Y
BU
Y
Y
Y
Y
Y
120V
12V
120V
12V
Transformer
Motor Resistance
Transformer
Motor Characteristics
(Ohms)
Power Supply 120 V AC Blue - Red 37.7
3 Filters Control
T20 Torx
Figure 2
Ribbon Cable
Electrical Shock Hazard
Disconnect power before servicing.
Replace all parts and panels before operating.
Failure to do so can result in death or
electrical shock.
Figure 4
6. Remove (2) T10 Torx screws that secure the switch
housing to the frame, see figure 4.
7. Remove (4) screws that secure the board to the
switch housing, see figure 5. Disconnect ribbon cable.
T10 Torx
Figure 1
Ribbon Cable
Figure 5
11
KXU4236YSS, KXU4230YSS (continued)
Kitchen Aid
To remove the motor:
1. Disconnect power from the range hood.
2. Remove the filters.
3. Remove (4) 1/4” hex head phillips screws from
the motor mounting bracket, see figure 1.
Screws
Figure 1
4. Slightly rotate and reposition the motor to
disengage the stamped metal “ears” that mate
with opening in the motor mounting bracket,
see figure 2 and 3.
Locking Tabs
(“Ears”)
Figure 2
Locking Tabs
Openings
(“Ears”)
Figure 3
N L N N N LA S4 S3 S2 S1
5 4 3 2 1 6 5 4 3 2 1
Y
Y
12 V
Y/G
GY
BK
BR
W
Y
R
1 2 3 4 5 6 7 8 9
Room temp. 73.4˚F (23˚C)
Y/G
BR
BK
GY
BU
Y
R
Motor Characteristics
Y
Power supply 120 VAC Y
Frequency 60 Hz M
S50
Power absorption 420 W
Current 3.7 A
2 Filters Control
Figure 2
Electrical Shock Hazard 5. Remove the switch housing from the light panel.
Disconnect power before servicing.
Replace all parts and panels before operating.
Failure to do so can result in death or
electrical shock.
Figure 3
6. Remove (4) T10 Torx screws that attach the
cover to the switch box assembly,
see figure 4.
Screw Locations
Figure 1
Switches
Figure 4
7. Test and or replace the affected switch.
14
KXU8030YSS, KXU8036YSS (continued)
Kitchen Aid
1. To remove the motor:
a. Disconnect power to the range hood.
b. Remove the filters.
c. Disconnect quick disconnect plug.
Quick Disconnect
Figure 1
d. Remove (4) hex head phillips screws from the
2 motor mount brackets, see figures 1 and 2.
Figure 2
15
KXU8030YSS, KXU8036YSS (continued)
Kitchen Aid
WIRING DIAGRAM
Wiring Diagram
Junction Box
GND L N
Y
W W
Y/G Y
BK
W
BU BR
BK
W
BR
On Off Off
Fan Speed Fan Light
BR
BK
GY
BK
W
R
Y
Motor Resistance
(Ohms) R R
BK
Blue - Red 18
Speed 3 Y
Blue - Gray 14.3
Speed 2
Blue - Black 9.8 (max)
Speed 1
BK
GY
W
Motor
BR
Y
Y/G
Characteristics
BR
BK
Frequency 60 HZ
Current 3.7A
Filters Control
Figure 2
To remove the motor:
1. Disconnect power from the range hood.
2. Remove the filters.
3. Disconnect control and harness connector,
see figure 3.
Electrical Shock Hazard
Disconnect power before servicing. Harness Connector
Replace all parts and panels before operating.
Failure to do so can result in death or
electrical shock.
Figure 3
4. Remove (4) T10 Torx screws from the motor
mounting plate (2) on each side, see figure 4.
Control 5. Disengage locating “ears” from the slots at
the back of each bracket, see figure 4.
Ears
Screws
Figure 1 Ears
17
KXW2336YSS, KXW2330YSS (continued)
Kitchen Aid
6. Pull motor out, see figure 3.
8. Remove (2) T10 Torx screws and disengage (2)
tabs that secure the wiring harness cover, see
figure 5.
Tabs
Figure 3
7. Remove (6) T10 Torx screws that mount the
electrical housing around the motor, Figure 5
see figure 4 and 4a.
9. Disconnect motor wiring harness from
connector block and remove motor, see figure 6.
Connector Block Motor Wiring Harness
Screws
Screws
Figure 6
Figure 4
Screws
Figure 4a
18
KXW2336YSS, KXW2330YSS (continued)
Kitchen Aid
Wiring Diagram
WIRING DIAGRAM
Junction box
L GND N
1
BK (Line)
2
BU (Neutral) AGC 02125
Y (Lamp)
3
Mechanical pushbuttons
W (Speed 1) with back light
4
R (Speed 2)
5
Y/G
BK
GY (Speed 3)
W
6 Switch operation
GY
BR
BK
W
R Position
Y
Connection
R
Y
BK
W
BK/R
Medium speed
BU/BK 28.8 (max) (1-5)
Frequency 60 Hz
12.5 uF
BR
Y
Y/G
GY
BK
BK
Y
120 V BU
Transformer 1 2 3 4 5 6 7
R
12 V R
BK
W
BU
GY
R
N
Y/G
Y/G
BU
BK
W
Light Panel
Light Switch
Control
2 Filters
Figure 2
5. Remove (2) T10 Torx screws, that secure the
on/off switch bracket to the frame, see figure 3.
On/Off Switch
Screws
Electrical Shock Hazard
Disconnect power before servicing.
Replace all parts and panels before operating.
Failure to do so can result in death or
electrical shock.
Light Switch
Side Panels
Strain Relief Switch Bracket
Figure 1 Figure 4
20
KXI4336YSS, KXI4342YSS, KXW4336YSS, KXW4330YSS, KXW4436YSS, KXW4430YSS (continued)
Kitchen Aid
7. Remove (2) T10 Torx screws to release the
control bracket, see figure 5.
Control Bracket
Figure 5
8. Remove (2) T10 Torx screws from the control
box cover, see figure 6.
Ribbon Connector
Figure 6
9. Remove (4) T10 Torx screws from the Electronic
User Interface board and disconnect ribbon
connector, see figure 6.
21
KXI4336YSS, KXI4342YSS, KXW4336YSS, KXW4330YSS, KXW4436YSS, KXW4430YSS (continued)
Kitchen Aid
Wiring Diagram
WIRING DIAGRAM
2 Filters Control
Remove These Screws
Figure 3
6. Remove (2) screws, one at on each side of the
control switch, see figure 4.
Figure 5
Figure 1
4. Remove (2) screws, one at each end of the
front filter retainer panel, see figure 2. Screw Locations
Switches
Figure 2 Figure 6
23
KXW8730YSS, KXW8736YSS, KXW8748YSS (continued)
Wiring Diagram
WIRING DIAGRAM
Junction box
N L Gnd
Y-G SE112A
BK
W W
W
BU W
R R
R
R
BU
BK
3 2 1 3 2 1 On 3 Off 1 On 3 Off 1 2 1
7 5 3 1 7 5 3 1 5 5 7 5 3
Off 1
Fan speed Fan speed Fan speed Fan Light
BK
8 6 4 2 8 6 4 2 6 4 2 6 4 2 8 6 4 2
BU
W
R
GY
BR
BR
BK
Y
W
GY
BK
BK
R
W
R
R R
R
BR
Speed 1
Closure Temperature
sensor Speed 2
temperature:
167˚F±5.4˚F
(75+/-3˚C) Speed 3
Opening
BK
GY
BU
W
temperature:
≥140˚F (60˚C)
W W 1 2 3 4 5 6
1
W
Y Y
2
25uF 25uF
Y-G
GY
BK
BU
W
BR
BR
3
BU
R
Y
4
BU 1 2 3 4 5 6 7 8 9 10
BU
Y/G
BR
W
GY
BK
BR
Y
5
R
Y
6
W
Y
Switch operation with button “1-2-3” Switch operation with button “ON-OFF” Switch operation with button “Light”
Position 1 2 3 Position ON OFF Position OFF 1 2
5 7
Connection 4 2 4 6 5 7 Connection 4 6 4 2 Connection 4 2 4 6 6 8
Action Speed 1 Speed 2 Speed 3 Action Motor ON Motor OFF Action Lights Off Low High
Intensity Intensity
Control
Figure 2
3 Filters
Figure 1
25
KXI9736YSS, KXI9748YS (continued)
Kitchen Aid
WIRING DIAGRAM
Wiring Diagram
Junction box
N L Gnd
1 2 3
SE110A
Y-G
BK
W W
W
BU
W
R R
BU
1 2 3 4
BK
3 2 1 3 2 1 On 3 Off On 3 Off 2 1 Off
7 5 3 1 7 5 3 1 5 1 5 1 7 5 3 1
Fan speed Fan speed Fan Fan Light
BK
8 6 4 2 8 6 4 2 6 4 2 6 4 2 8 6 4 2
BK
GY
BR
BK
BU
GY
BR
W
BK
R
R
R
Y
W
R R
R
BR
Speed 1
Temperature
Closure sensor Speed 2
temperature:
167˚F±5.4˚F Speed 3
(75+/-3˚C)
Opening
GY
BK
temperature: BU W
≥140˚F (60˚C)
W W 1 2 3 4 5 6
W
Y Y
25uF 25uF
Y-G
GY
BU
BK
W
BR
BR
BU
R
Y
BU 1 2 3 4 5 6 7 8 9 10
BU
GY
Y/G
BR
BK
BR
W
R
Y
Y
W
Y
Switch operation with button “1-2-3” Switch operation with button “ON-OFF” Switch operation with button “Light”
Position 1 2 3 Position ON OFF Position OFF 1 2
5 7
Connection 4 2 4 6 5 7 Connection 4 6 4 2 Connection 4 2 4 6 6 8
Action Action Low High
Speed 1 Speed 2 Speed 3 Action Motor ON Motor OFF Lights Off Intensity Intensity
27
In-Line, Internal and External Blower Systems
These are dedicated blowers designed to work with the range hood models listed below. Blower models and mounting locations
are determined at the time of installation. Blowers are matched to range hood models based on individual installation
requirements.
28
Internal Blower Systems 3. Ru
UXB0600D, UXB1200D,InstallUXI600D, UXI1200D
Hood Liner Internal Blower Motor hoo
pla
1. Install the hood liner blower motor assembly inside the hood 3. R
Single
liner
InstallInternal
canopy
HoodwithBlower Motor
theInternal
Liner wiring Assembly
connection
Blower to the left for the
Motor 3. Rh
Installmotor
single Hoodsystem
Liner and
Internal
to theBlower
front orMotor
top for the dual motor h
p
3. system.
Disconnect the motor wiring harness from the p
1. Install the hood liner blower motor assembly inside the hood
1. locations
Install shown
the hood
liner canopy withliner
for a single
theblower motoror Dual
assembly
wiring connection
blower
to theinside
motor
left forthe
thehood
Single system.
liner canopy
Blower
single See
Motor
motor marked
with
systemthe
Assembly
and locations
wiring
to connection
the “A”.
front or to the
top for left
the for
dualthemotor
single
system. motor system and to the front or top for the dual motor
system.
Single Blower Motor Assembly
Single Blower Motor Assembly
6.4. Remove
Push the
the right endpower supply
of the motor wires and
mounting plateBconnector
up and snap it
into the spring tab.
from the range hood through the hole in the
NOTE:
6. Attach The spring
power cord tab mounting
A. Motor shouldfrom
connector be hole
plate outside
the range thehood
slot in
tothe 5. Remove the screws that secure the blower motor assembly
right end
mounting
connector of the
plate.
on
B.
wiring
Power
box.motor mounting plate.
supply wires and connector
to the in-line blower
A. housing and setplate
Motor mounting them aside.
4. Push the right end of the motor mounting plate up and snap it
into the spring tab.
6. Pull the spring clipB.toSpring
release
clipthe blower motor assembly.
NOTE: The spring tab should be outside the slot in the
Remove the blower motor assembly from the housing and
mounting plate.
A. Wiring connection 5. place
Align itmounting holessurface.
on a covered in motor mounting plate with motor
mounting clip nuts and install 6 x 16 mm screws and
2. Slide the left mounting plate flange under the motor
A mounting 6.4 mm lock washers (quantity 2 for single motor; quantity 5
bracket. for dual motor).
A A
A A
B C
B
B B
C
Excessive Weight
A. Wiring Hazard
box connector
Use two or moreB.people to connector
Power supply move and install
from range hood
in-line blower motor system.
7. Go to the
Failure to“Make Electrical
do so Power Supply
can result Connection
in back to Hood
or other D
Liner” section.
injury. A. Front cover
B. Blower mounting screws
Install Hood Liner In-Line
Electrical Shock (External
Hazard Type) C. Spring clip
Disconnect powerBlower
beforeMotor
servicing.
D. Bottom housing mounting holes
E. Motor electrical plug
NOTE: Your hood liner requires you to purchase either an internal
Replace
type all parts
or an in-line and
(external panels
type) blowerbefore operating.
motor system. See
FailureMotor
“Blower to do so can
System” result
in the in death
“Accessories” or
section. Install In-line Blower System
electrical shock.
Prepare for Mounting the In-Line Blower System NOTE: The blower motor housing can be mounted using 4 holes
from either the inlet side or the outlet side of the blower.
The in-line blower system must be fastened to a secure structure
of the roof, ceiling, wall, floor, or new or existing frame Outlet Side A A
construction. The 4 holes on either the inlet (bottom) side or the
outlet (top) side of the blower must be used to mount the in-line
blower system to the structure.
NOTE: The mounting hole locations must span the studs.
Additional stud framing may be required. Plywood may be used
to span open areas between ceiling joists or roof rafters to aid A
UXI0600D
installation. (600CFM),
This structure must beUXI1200D (1200
strong enough CFM) the
to support
weight of the in-line blower system (50 lb [22.6 kg] min).
Removing an In-Line Blower System:
1. Prepare
Disconnect power
the In-line to the
Blower range hood.
System A
Use two or more people, to remove the in-line
blower motor system from the mounting location.
2. Remove the 10 screws WARNINGfrom the front cover of the
in-line blower motor housing.
3. Remove the front cover
Excessive of theHazard
Weight in-line blower
motor
Use two housing and set
or more people to it aside.
move and install in-line
blower motor system.
NOTE: To make
Failure the
to do so blower
can result motor
in back housing easier to
or other injury.
remove, the blower motor assembly can be removed first. A
4.1. Disconnect the motor
Using two or more people, electrical plugblower
move the in-line from the
motor
blower
system tomotor assembly.
the mounting location. Inlet Side A
2. Remove the 10 screws from the front cover of the in-line
blower motor housing and set them aside.
31 A. Mounting holes
3. Remove the front cover of the in-line blower motor housing 1. Position the in-line blower motor housing in its mounting
2. Determine
D the location where the ¹⁄₂" (1.3 cm) wiring conduit
will be routed through the ceiling or wall between the in-line
A.blower
Front and
cover the hood liner.
3. B.Drill
Blower mounting
a 1¹⁄₄" (3.2 cm) screws
hole at this location.
4. C.Locate
Springthe
D.housing
Bottomand housing
In-Line Blower Systems (continued)
clipelectrical terminal boxes in the in-line blower
hood mounting holesthe terminal box covers and
liner. Remove
E.set the covers
Motor andplug
electrical
UXI0600D, UXI1200D Electrical Shock Hazard
screws aside.
11
32
External Blower Systems
KPEU722M, KPEC922M
Figure 3
35
Additional Range Hood Wiring Diagrams (continued)
WIRING
Models: JXI8042W, DIAGRAM
JXI8036W, JXI8242W, JXI8236W
Electronic User Interface
CON2
GND L N
W
BK
Y/G
Electronic Power Board
CON1
N L NL NM LA S4 S3 S2 S1
P1 P2 P4A P3 P4 P5 P9 P8 P7 P6
5 4 3 2 1 6 5 4 3 2 1 CON4
CON3
BU
Y
W
CON7
BU
BU
BK CON8
GY
BK
BU
BR
Y/G
W
R
Y
CON 6
BU
L 1 2 3 4 5 6 7 8 9
N CON 11
CON 12 CON 5
BU
Y
BU
N L CON 9
Y
Y/G
BK
BR
YL
GY
BU
W
R
CON 10
BU
Y
BU
BU
Y
Y
BU
BU
Y
Y
Y-G
BK
N L NL NM LA S3 S2 S1
TRANSFORMER
P1 P2 P4A P3 P4 P5 P8 P7 P6
5 4 3 2 1 6 5 4 3 2 1 CON4
CON3
SEC
PRI
BR
BR
GY
BU
BK
W
R
R
R
BR
Y
ATTENTION!:
WITH 4 LAMPS
BU
GY
BK
R
W
SEC
Y-G
TRANSFORMER
Y
PRI
BR
Y
R 1
Y
BR
W
GY
R
BK
Y-G
BU
Y-G
Y
Y Y
BR
Y Y
SE1Q7A
BU W
1
BR Y
G Y-G
2
GY
3
Y-G Y-G
GY
BK
BK
BU
YEL
Y-G
BR
BK
W
BU
BL
BL
3 2 1
BK
Y-G
BR
BR
BR
R
R
2 4 6 8 10 2 4 6
BU
BK
BR
LCB R
BRW
W
FSCB
1 3 5 7 9 1 3 5 R
BK
12V TRANSFOR-
BR
Y
MER
Y 120V
BU
BU
BK
BU BU
WIRING DIAGRAM
Electronic User Interface
BE1EWA
CON2
GND L N
Y/G
Electronic Power Board
CON1
BE1CAA
N L NL NM LA S4 S3 S2 S1
P1 P2 P4A P3 P4 P5 P9 P8 P7 P6
5 4 3 2 1
CON3 6 5 4 3 2 1 CON4
BU
Y
W
CON7
BK CON8
GY
BK
BU
BR
Y/G
W
R
BU
Y
CON 6
1 2 3 4 5 6 7 8 9
N L CON 13
CON 14 CON 5
BK
BR
GY
BU
Y
Y/G
R
BU
N L N L
CON 15 CON 16
12
Turn off the range hood and allow the halogen lamp to cool. To
Additional Range Hood Wiring Diagrams (continued)
avoid damage or decreasing the life of the new bulb, do not
touch bulb with bare fingers. Replace bulb, using tissue or
JXW8230W, JXW8236W
wearing cotton gloves to handle bulb.
3. Remove the lamp and replace with a 12-volt, 20-watt
If new lights do not operate, make sure the lamps are inserted
correctly before calling service. Jenn-Airmaximum, halogen lamp made for a G-4 base.
4. Replace the light cover.
5. Reconnect power.
WIRING DIAGRAM
Electronic User Interface
CON2
GND L N
Y/G
Electronic Power Board
CON1
N L NL NM LA S4 S3 S2 S1
P1 P2 P4A P3 P4 P5 P9 P8 P7 P6
5 4 3 2 1
CON3 BU 6 5 4 3 2 1 CON4
Y
W
Y CON7
BK CON8
BR
Y/G
GY
BK
MATEUR
TRANSTOR-
W
R
CON 6
1 2 3 4 5 6 7 8 9
CON 5
120V
12V
G Y
BK
BR
BU
Y/G
R
Y
BU
Y Y M
12
Y/G
BK
W
BU
BR
BK
W
BK
W
BK
BK
BK
BR
BU
GY
BK
W
R
Y/G
Y/G
BU
GY
BK
W
BK
L N
GY
R
W
IR switch
Junction box Position ON OFF
Switch No
N L Gnd Switch operation Connection 1 2
connection
Action Light ON Light OFF
IR lamps
Y-G
BK
W W
W
BU W
R R
BU
BK
R
On 3 Off 1 On 3 Off 1 2 1 Off 1
7 5 3 1 7 5 3 1 5 5 7 5 3
Fan speed Fan speed Fan Fan Light
BK
8 6 4 2 8 6 4 2 6 4 2 6 4 2 8 6 4 2
GY
GY
BR
BU
W
BR
BK
BK
BK
R
R
R
R
W
Y
R R R
BR
Temperature Speed 1
Closure
temperature: sensor Speed 2
167˚F±5.4˚F
(75+/-3˚C) Speed 3
Opening
GY
BK
W
temperature: BU
≥140˚F (60˚C)
W W 1 2 3 4 5 6
1
W
Y Y
2
25uF 25uF
Y-G
BU
GY
BK
BR
BR
W
3
BU
Y
4
BU 1 2 3 4 5 6 7 8 9 10
W
GY
Y/G
BR
BU
BR
BK
5
R
Y
Y
6
W
Y
Optional
lamp used
in 48" (121.9 cm)
size hood
Optional kit with 1 motor
Lamps
Switch operation with button “1-2-3” Switch operation with button “ON-OFF” Switch operation with button “Light”
Position 1 2 3 Position ON OFF Position OFF 1 2
5 7
Connection 4 2 4 6 5 7 Connection 4 6 4 2 Connection 4 2 4 6 6 8
Action Speed 1 Speed 2 Speed 3 Lights Off Low High
Action Motor ON Motor OFF Action Intensity Intensity
1 2 3
SE110A
Y-G
BK
W W
W
BU
W
R R
R
1 2 3 4
BU
BK
3 2 1 3 2 1 On Off On Off 2 1 Off
7 5 3 1 7 5 3 1 5 3 1 5 3 1 7 5 3 1
Fan speed Fan speed Fan Fan Light
8 6 4 2 8 6 4 2 6 4 2 6 4 2 8 6 4 2
BK
BK
W
GY
BU
BK
R
BR
R
GY
BK
R
BR
Y
W
R
R R
R
BR
Speed 1
Temperature
Closure sensor Speed 2
temperature:
167˚F±5.4˚F Speed 3
(75+/-3˚C)
Opening
BU
GY
BK
temperature:
W
≥140˚F (60˚C)
W W 1 2 3 4 5 6
W
Y Y
25uF 25uF
Y-G
BU
GY
BK
W
BR
BU
BR
Y
BU 1 2 3 4 5 6 7 8 9 10
BU
Y/G
GY
W
BK
BR
BR
R
Y
W
Y
Switch operation with button “1-2-3” Switch operation with button “ON-OFF” Switch operation with button “Light”
Position 1 2 3 Position ON OFF Position OFF 1 2
5 7
Connection 4 2 4 6 5 7 Connection 4 6 4 2 Connection 4 2 4 6 6 8
Action Action Low High
Speed 1 Speed 2 Speed 3 Action Motor ON Motor OFF Lights Off Intensity Intensity
SEL0015013
Motor Characteristics
Power Supply 120 V
Y
Frequency 60 Hz Y
User Interface
Speed 4
BK
GY Y Y
R R
Main Board Speed 3
Speed 2
R
BR BR Speed 1
W
Lamp Y
Neutral
Y
Neutral
BU
Y Y
L1
BK
Neutral W
W W
EMC Filter
Secondary
N
Primary
Y/G
Transformer
BK BK
L Y/G
BR BR
Y Y
Speed Motor Resistance (Ohms) Y/G Y/G
1
2
BU/W
BU/R
45.1 Min.
37.7
M W
R
W
R
GY GY
3 BU/GY 30.3 BK BK
4 BU/BK 20.8 Max. BU BU