Documente Academic
Documente Profesional
Documente Cultură
Order No.
outdoor unit
YJHJZH018BARRAFX-SM Table of Contents
Table of Contents
1. Introduction ……………………………………………………………………..1
3. Specifications …………………………………………………………………...6
9. Removal Procedure……………………………..…….…………………...….80
1. Introduction
1.1 Safety Cautions
Be sure to read the following safety cautions before conducting repair work.
The caution items are classified into “Warning” and “Caution”. The “Warning” items are especially important
since they can lead to death or serious injury if they are not followed closely. The “Caution” items can also lead
to serious accidents under some conditions if they are not followed. Therefore, be sure to observe all the safety
caution items described below.
About the pictograms
This symbol indicates an item for which caution must be exercised.
The pictogram shows the item to which attention must be paid.
This symbol indicates a prohibited action.
The prohibited item or action is shown inside or near the symbol.
This symbol indicates an action that must be taken, or an instruction.
The instruction is shown inside or near the symbol.
After the repair work is complete, be sure to conduct a test operation to ensure that the equipment operates
normally, and explain the cautions for operating the product to the customer.
Warning
Be sure to disconnect the power cable plug from the plug socket before disassembling the equipment for
a repair.
Working on the equipment that is connected to a power supply can cause an electrical shook.
If it is necessary to supply power to the equipment to conduct the repair or inspecting the circuits, do not
touch any electrically charged sections of the equipment.
If the refrigerant gas discharges during the repair work, do not touch the discharging refrigerant gas.The
refrigerant gas can cause frostbite.
When disconnecting the suction or discharge pipe of the compressor at the welded section, release the
refrigerant gas completely at a well-ventilated place first.
If there is a gas remaining inside the compressor, the refrigerant gas or refrigerating machine oil
discharges when the pipe is disconnected, and it can cause injury.
If the refrigerant gas leaks during the repair work, ventilate the area. The refrigerant gas can generate
toxic gases when it contacts flames.
The step-up capacitor supplies high-voltage electricity to the electrical components of the outdoor unit.
Be sure to discharge the capacitor completely before conducting repair work.A charged capacitor can
cause an electrical shock.
Do not start or stop the air conditioner operation by plugging or unplugging the power cable plug.
Plugging or unplugging the power cable plug to operate the equipment can cause an electrical shock or
fire.
Warning
Do not repair the electrical components with wet hands. Working on the equipment with wet hands can
cause an electrical shock.
Do not clean the air conditioner by splashing water. Washing the unit with water can cause an electrical
shock.
Be sure to provide the grounding when repairing the equipment in a humid or wet place, to avoid electrical
shocks.
Be sure to turn off the power switch and unplug the power cable when cleaning the equipment. The
internal fan rotates at a high speed, and cause injury.
Do not tilt the unit when removing it. The water inside the unit can spill and wet the furniture and floor.
Be sure to check that the refrigerating cycle section has cooled down sufficiently before conducting repair
work. Working on the unit when the refrigerating cycle section is hot can cause burns.
Use the welder in a well-ventilated place. Using the welder in an enclosed room can cause oxygen
deficiency.
Warning
Be sure to use an exclusive power circuit for the equipment, and follow the technical standards related to
the electrical equipment, the internal wiring regulations and the instruction manual for installation when
conducting electrical work.
Insufficient power circuit capacity and improper electrical work can cause an electrical shock or fire.
Be sure to use the specified cable to connect between the indoor and outdoor units. Make the
connections securely and route the cable properly so that there is no force pulling the cable at the
connection terminals.
Improper connections can cause excessive heat generation or fire.
When connecting the cable between the indoor and outdoor units, make sure that the terminal cover does
not lift off or dismount because of the cable.
If the cover is not mounted properly, the terminal connection section can cause an electrical shock,
excessive heat generation or fire.
Do not damage or modify the power cable.
Damaged or modified power cable can cause an electrical shock or fire. Placing heavy items on the
power cable, and heating or pulling the power cable can damage the cable.
Do not mix air or gas other than the specified refrigerant (R-410A / R22) in the refrigerant system.
If air enters the refrigerating system, an excessively high pressure results, causing equipment damage
and injury.
If the refrigerant gas leaks, be sure to locate the leak and repair it before charging the refrigerant. After
charging refrigerant, make sure that there is no refrigerant leak.
If the leak cannot be located and the repair work must be stopped, be sure to perform pump-down and
close the service valve, to prevent the refrigerant gas from leaking into the room. The refrigerant gas itself
is harmless, but it can generate toxic gases when it contacts flames, such as fan and other heaters,
stoves and ranges.
When replacing the coin battery in the remote controller, be sure to disposed of the old battery to prevent
children from swallowing it.
If a child swallows the coin battery, see a doctor immediately.
Caution
Installation of a leakage breaker is necessary in some cases depending on the conditions of the
installation site, to prevent electrical shocks.
Do not install the equipment in a place where there is a possibility of combustible gas leaks.
If a combustible gas leaks and remains around the unit, it can cause a fire.
For
Be sure to install the packing and seal on the installation frame properly. If the packing and seal are not
integral
installed properly, water can enter the room and wet the furniture and floor.
units only
Warning
Check to make sure that the power cable plug is not dirty or loose, then insert the plug into a power outlet
all the way.
If the plug has dust or loose connection, it can cause an electrical shock or fire.
If the power cable and lead wires have scratches or deteriorated, be sure to replace them.
Damaged cable and wires can cause an electrical shock, excessive heat generation or fire.
Warning
Do not use a joined power cable or extension cable, or share the same power outlet with other electrical
appliances, since it can cause an electrical shock, excessive heat generation or fire.
Caution
Check to see if the parts and wires are mounted and connected properly, and if the connections at the
soldered or crimped terminals are secure. Improper installation and connections can cause excessive
heat generation, fire or an electrical shock.
If the installation platform or frame has corroded, replace it. Corroded installation platform or frame can
cause the unit to fall, resulting in injury.
Check the grounding, and repair it if the equipment is not properly grounded. Improper grounding can
cause an electrical shock.
Be sure to measure the insulation resistance after the repair, and make sure that the resistance is 1 M
ohm or higher.
Faulty insulation can cause an electrical shock.
Be sure to check the drainage of the indoor unit after the repair.
Faulty drainage can cause the water to enter the room and wet the furniture and floor.
Functions
AS18GN3ERA
Category
1U18EN2ERA
Healthy negative ion make your room full of an abundance natural negative ions. N
Child lock Avoid the child's wrong operation on the remote controller Y
3D air flow The 3D airflow is able to deliver the airflow horizontally and vertically. N
24Hour timer Use the timer function to set on,or off,or from on to off,or from off to on Y
Easy clean design The panel is easy to wash and the airflow vents can be detached easily Y
Intelligent air With twin-blade technology ,the airflow can be adjusted not to blow directly Y
Anti-mold filter Catches most small particles and remove unpleasant odors effectively. Y
The setting temprature and the indoor noise can be adjusted to a more comfortable
Sleep mode Y
level when you set the "sleep mode"during night sleep
Constant temperature
Make dehumidifying in the room while keeping the constant temperature inside N
dehumidification
5
YJHJZH018BARRAFX-SM
3. Specifications
AS18GN3ERA/1U18EN2ERA
Cooling Heating
4.8 4.8
16381 16381
4127 4127
2.0
4.1 6.1
163~941~2250 377~1412~2850
96 97
5.1 3.4
6.35
12.7
16.0
25
15
10
20
AS18GN3ERA
14.2 15.0
12.7 13.5
11.2 13.0
- -
40
4.1 6.1
941 1412
96 96
938X187X265
1016X304X360
10.5
12.5
55/52/48
55
6
YJHJZH018BARRAFX-SM Specifications
1U18EN2ERA
SNB130FGYMC-L1
900
FV50S
0.5
R410a
1.2
33 33
1176.5 1176.5
Propeller
40
4.1 6.1
941 1412
98 98
15
780X245X640
930X340X714
33
35.5
54
54
5m
7
YJHJZH018BARRAFX-SM Connector Wiring Diagram
3ULQWHG&LUFXLW%RDUG&RQQHFWRU:LULQJ'LDJUDP
4.1˖Indoor unit Connectors
Connectors
PCB(1) (Control PCB) For AS18GN3ERA
1) CN26 Connector for fan motor
2) CN1 Connector for heat exchanger thermistor and Room temperature thermistor
3) CN11’ Connector for UP&DOWN STEP motor
4) CON2 Connector for power N wire
5) CON1 Connector for power L
6) CON13 Connector for power GRN
7) CN32 Connector for display board
8) CON7 Connector for communicate between the indoor board and the outdoor board
9) CN34 Connector for long-range control
PCB(1)
CN1 CN11’
CN32
CN26
CON13
CON1
CON2
CN34
CON7
PCB (1)
CN21
CN17
CN18
CN19
CN20
CN16
CN4
CN10
CN3
CN1
CN9
CN8
CN2
CN5 CN6
PCB (2)
CN6 CN7
CN11
CN10
CN5
CN4
CN3
CN2
CN1
Set speed
5.1.8 Timing.
You can set 24 hours’ on/off timing accordingly. After the setting, the timing indicator will be lightened.
Also, the light will be turning off after the timing is finished. The followings are several timing methods.
1.system /on timing: The timing indicator will be lightened and the indoor system is under the waiting
mode. The light will be turned off when the timing is finished and the rest of the system will operate
under a normal condition. The timing starts since the last reception of the timing singal. You can have
the dormacy setting under the timing mode, the order of your settings will be operated according to
the timing settings.
2.system /off timing: When the system is turned on, the timing indicator is lightened, the rest of the
system will operated under a normal condition. When set time comes, the indicator light will be turned
off and the system will be turned off. If you have set the dormant functions, the order of your settings
will be operated according to the timing settings.
3 .system /on and off timing: The settings will be completed according to the orders.
T <1 ˙1 ˙2 ˙3 4
The percentage of the 50% 70% 100% 120% 160%
rated frequency P
Heating mode˖
T <1 ˙1 ˙2 ˙3 4
The percentage of the 150% 170% 200% 220% 240%
rated frequency P
The indoor set Breeze Low Medium High Strong Quiet Healthy
airflow speed airflow
The percentage 70ˁ 80% 90% 100% 180% 65% 65%
of the rated
frequency Ki
The calculation of the actual output frequency: when there is no healthy airflow: F =F-ED-*hPhK
When the healthy airflow has been set: F =F-ED-*hPhK˄airflow speed˅hK˄healthy airflow˅
When refrigerating, it is needed to satisfy ˢˉ˩INˉ̀< F<ˢˉ˩˝˴ˉ̀
When heating, it is needed to satisfy ˢˉ˩INˉr< F<ˢˉ˩˝˴ˉr
11 //ice_temp_3+5
9
ice_temp_3+3 Increasing slowly
8 //ice_temp_3+2
Keeping the frequency
ice_temp_3 7 6
ice_temp_2 5 Decreasing slowly
ice_temp_1 3 Decreasing rapidly ice_temp_1
0 Stop
When Tpg_indoor ice_temp_1 , the frequency of the compressor decreases at the speed of
1HZ/1second.
When Tpg_indoor ice_temp_2 , the frequency of the compressor decreases at the speed of
1HZ/10seconds.
25 Domestic Air Conditioner
YJHJZH018BARRAFX Funcitions and Control
When Tpg_indoor begins to rise again, and ice_temp_2İTpg_indoorİ ice_temp_3ć, the frequency
of thecompressor doesn’t change.
When ice_temp_3LJTpg_indoorLJice_temp_3+3ć, the frequency of the compressor increases at the
speed of 1HZ/10seconds.
For example, Tpg_indoorİ0ćˈlast for 2 minutes, and then the outdoor unit will stop, and report
underload malfunction, but don’t send malfunction report to the indoor.
The compressor stops for more than 3 minutes, Tpg_indoor> ice_temp_3+2ć, the compressor
recovers.
R25ć=10K¡f3%
B25ć/50ć=3700Kf3%
Discharging Sensor
R80ć=50K¡f3%
B25/80ć=4450Kf3%
Temp.((ć)) Max.(Kȍ) Normal(Kȍ) Min.(Kȍ) Tolerance(ć)
39
YJHJYH018BARRAFX-SM System Configration
5 7
Operation
Base Operation Emergency operation and test operation
Emergency Operation: Pi
Use this operation only when the remote controller
Remote controller is defective or lost.
When the emergency operation switch is
SPEED
pressed,the" Pi "sound is heard once, which
means the start of this operation.
In this operation, the system automatically selects
the operation modes,cooling or fan or heat,
according to the room. temperature.
Room Operation Designated Timer Air flow
temperature mode temperature mode
ABOVE 23 C
O
COOLING 26 C
O NO AUTOMATIC
BELOW 23OC HEAT 23OC NO AUTOMATIC
Operation e tDisplay
o m e R
Note
Cautions:
Mode r Board
e l l o r t n o C When adjusting the flap by hand,turn off the unit.
Under the mode of auto operation, air conditioner will
automatically select Cool or Heat operation according When humidity is high,condensate water might occur
AUTO
to room temperature. When FAN is set to AUTO, the at air outlet if all vertical louvers are adjusted to left or
air conditioner automatically adjusts the fan speed
according to room temperature.
right.
COOL
It is advisable not to keep horizontal flap at downward
In DRY mode, when room temperature becomes
lower than temp.setting+2 oC,unit will run intermittently position for a long time in COOLor DRY mode ,
DRY at LOW speed regardless of FAN setting. otherwise, condensate water might occur.
In FAN operation mode, the unit will not operate in
COOL or HEAT mode but only in FAN mode ,AUTO is
Note:
FAN not available in FAN mode.And temp.setting is disabled. When restart after remote turning off, the remote
In FAN mode,SLEEP operation is not available.
controller will automatically memorize the previous
set swing position.
1 Domestic Air Conditioner
YJHJZH018BARRAFX-SM
Parts and Functions
Operation
Sleep Operation
4. In FAN mode
Press button to enter additional options, when It has no SLEEP function.
cycle display to , will flash. And then press 5.Set the wind speed change when sleeping
If the wind speed is high or middle before setting for the
enter to sleep function.
sleep, set for lowing the wind speed after sleeping.
If it is low wind, no change.
Note
When TIMER function is set, the sleeping function can’t be
set up .After the sleeping function is set up , if user resets
TIMER function, the sleeping function will be cancelled; the
machine will be in the state of timing-on.
POWER/QUIET Operation
(1) POWER Operation
Operation Mode
When you need rapid heating or cooling, you can use this function.
1. In COOL,DRY mode
1 hours after SLEEP mode starts,temp.will become 1OC Press button to enter additional options, when cycle
higher than temp.setting.After another 1 hours,temp.rises display to , will flash,and then press ,enter to
by 1OC futher.The unit will run for further 6 hours then stops
power function. When cancel the function, please enter
Temp. is higher than temp.setting so that room temperature
won’t be too low for your sleep. additional options again and to cancel power function.
1 hr Decreases 2OC
1 hr
Decreases 2OC
3 hrs
3 hrs Rises 1OC
SLEEP SLEEP
operation starts operation stops
In HEAT mode
3. In AUTO mode
The unit operaters in corresponding sleep mode
adapted to the automatically selected operation mode.
EUROPEAN REGULATIONS
Operation CONFORMITY FOR THE MODELS
CE
Timer On/Off On-Off Operation All the products are in conformity with the following
1.After unit starts, select your desired operation mode. European provision:
2.Press TIMER button to change TIMER mode. Every - Low Voltage Directive 73/23/EEC
time the button is pressed, display changes as follows: - Low Voltage Directive 2006/95/EC
Remote controller: -Electomagnetic CompatibilitY 89/336/EEC
BLANK -Electomagnetic CompatibilitY 2004/108/EC
0.5h 0.5h 0.5h 0.5h ROHS
TIMER ON TIMER OFF TIMER ON-OFF TIMER OFF-ON The products are fulfilled with the requirements in the
Then select your desired TIMER mode (TIMER ON or directive 2002/95/EEC of the European parliament and of
TIMER OFF or TIMER ON-OFF). " "or " "will flash. council on the Restriction of the use of Certain Hazardous
Substances in Electrical and Electronic Equipment (EU
3.Press / button to set time. RoHS Directive)
Press the button for each time, setting time in the first WEEE
12 hours increased by 0.5 hour every time, after 12 In accordance with the directive 2002/96/CE of the European
hours,increased by 1 hour every time.
parliament, herewith we inform the consumer about the dis-
Press the button for each time, settiing time in the first posal requirements of the electrical and electronic products.
12 hours decreased by 0.5 hour every time, after 12 DISPOSAL REQUIREMENTS:
hours,decreased by 1 hour every time. Your air conditioning product is marked with this
It can be adjusted within 24 hours.
4.Confirm timer setting symbol.This means that electrical and electronic
products shall not be mixed with unsorted
After adjust the time,press button and confirm the household waste. Do not try to dismantle the
time ON or OFF button will not flash any more. system yourself : the dismantling of the air
5.Cancel timer setting conditioning system,treatment of the refrigerant, of oil and of
Press the timer button by times until the time display other part must be done by a qualified installer in accordance
eliminated.
with relevant local and national legislation. Air conditioners
Hints: must be treated at a specialized treatment facility for reuse,
After replacing batteries or a power failure happens, time recycling and recovery. By ensuring this product is disposed
setting should be reset. of correctly, you will help to prevent potential negative cons-
According to the Time setting sequence of TIMER ON or equences for the environment and humen health. Please
TIMER OFF, either Start-Stop or Stop-Start can be achieved. contact the installer or local authority for more information.
Healthy airflow Operation Battery must be removed from the remote controller and dis-
posed of separately in accordance with relevant local and
1.Press to starting nationl legislation.
Setting the comfort work conditions.
2.The setting of healthy airflow function
IMPORTANT INFORMATION REGA-
Press button to enter additional options,Press this RDING THE REFRIGERANT USED
button continuously, the louvers location will cycle between
Contains fluorinated greenhouse gases
in the following three locations, to choose the swing location covered by the Kyoto Protocol A
what you needed,and then press button to confirm. R410A 1= kg
B
Healthy Healthy
airflow airflow
Present 2 2= kg
position C
upwarder downwarder 1
3.The cancel of the healthy airflow function 1+2= kg
D
button continuously, the louvers location will cycle between This product contains fluorinated greenhouse gases covered by
in the following three locations again,and then press the Kyoto Protocol. Do not vent into the atmosphere.
button to cancel. Refrigerant type:R410A
GWP* value:1975
Notice: Do not direct the flap by hand. Otherwise, the GWP=global warming potential
grille will run incorrectly. If the grille is not run correctly, stop Please fill in with indelible ink,
•1 the factory refrigerant charge of the product
for a minute and then start, adjusting by remote •2 the additional refrigerant amount charged in the field and
controller. • 1+2 the total refrigerant charge
Note: on the refrigerant charge label supplied with the product.
The filled out label must be adhered in the proximity of the product
1.After setting the healthy airflow function, the position charging port (e.g. onto the inside of the stop value cover).
grill is fixed. A contains fluorinated greenhouse gases covered by the Kyoto
2.In heating, it is better to select the mode. Protocol
3.In cooling, it is better to select the mode. B factory refrigerant charge of the product: see unit name plate
4.In cooling and dry, using the air conditioner for a long C additional refrigerant amount charged in the field
time under the high air humidity, condensate water may D total refrigerant charge
occur at the grille . E outdoor unit
F refrigerant cylinder and manifold for charging
Maintenance
For Smart Use of The Air Conditioner
Setting of proper room Do not block the air inlet Remote Controller Indoor Body
temperature or outlet
NOTE:
Detach old Air Purifying Filter The photocatalyst air purifying filter will be solarized in fixed
time. In normal family, it will be solarized every 6 months.
Cautions
WARNING
Please call Sales/Service Shop for the Installation.
Do not attempt to install the air conditioner by yourself because improper works
may cause electric shock, fire, water leakage.
WARNING
When abnormality such as burnt-small found, Use an exclusive Check proper
immediately stop the operation button and power source installation of the
contact sales shop. with a circuit drainage securely
breaker
Do not start or stop the Do not channel the air flow directly Do not try to repair or Connect the earth
operation by disconnecting at people, especially at infants or reconstruct by yourself.
the aged. cable.
the power supply cord
and so on.
earthing
PROHIBITION PROHIBITION
CAUTION
Do not use for the purpose of storage of Take fresh air occasionally especially Do not operate the switch with
food, art work, precise equipment, when gas appliance is running at the wet hand.
breeding, or cultivation. same time.
STRICT
PROHIBITION ENFORCEMENT PROHIBITION
Do not install the unit near a fireplace Check good condition of the Do not pour water onto the unit
or other heating apparatus. installation stand for cleaning
Phenomenon Cause or check points Do not allow children to play with the air conditioner.In no
case should children be allowed to sit on the outdoor unit.
The system When unit is stopped, it won't restart
does not restart immediately until 3 minutes have Specifications
immediately. elapsed to protect the system.
When the electric plug is pulled out The refrigerating circuit is leak-proof.
and reinserted, the protection circuit
will work for 3 minutes to protect the The machine is adaptive in following situation
air conditioner. 1.Applicable ambient temperature range:
During unit operation or at stop,
a swishing or gurgling noise may Maximum:D.B/W.B 32oC/23oC
Noise is heard be heard.At first 2-3 minutes after Indoor Minimum:D.B/W.B 21oC/15oC
unit start, this noise is more noticeable. Cooling
(This noise is generated by Maximum:D.B/W.B 46oC/26oC
refrigerant flowing in the system.)
Outdoor Minimum: D.B 18oC
During unit operation, a cracking Maximum:D.B 27oC
noise may be heard.This noise is Indoor Minimum: D.B 15oC
generated by the casing expanding
Normal or shrinking because of Heating
Maximum:D.B/W.B 24oC/18oC
Performance temperature changes. Outdoor
Minimum:D.B/W.B - 7 oC/-8oC
inspection Should there be a big noise from o o
air flow in unit operation, air Outdoor Maximum:D.B/W.B 24 C/18 C
filter may be too dirty. (INVERTER) Minimum:D.B -15oC
This is because the system
Smells are circulates smells from the interior 2. If the power supply cord is damaged, it must be replaced by the
generated. air such as the smell of furniture, manufacturer or its service agent or a similar qualified person.
paint, cigarettes.
3.If the fuse of indoor unit on PC board is broken,please change
Mist or steam are
blown out. During COOL or DRY operation, it with the type of T. 3.15A/ 250V. If the fuse of outdoor unit is
indoor unit may blow out mist. broken,change it with the type of T.25A/250V
This is due to the sudden cooling
of indoor air. 4. The wiring method should be in line with the local wiring standard.
Arrangement of piping
directions
Rear left
more than Left Rear
10cm right
Right
Below
The distance between the indoor unit and the Àoor should be more than 2m.
Please be subject to the actual product purchased,the above picture is just for your reference.
Heat insulation
material Piping
B= Ø 70mm Lid for right Pipe supporting
piping plate
Lid for left piping Drain hose
Lid for under piping pipe
A=145mm
Indoor/outdoor electric cable and drain hose must be bound with
efrigerant piping by protecting tape.
[ Other direction piping ]
B= 70mm Cut away, with a nipper, the lid for piping according to the piping
direction and then bend the pipe according to theposition of wall
hole. When bending, be careful not to crash pipes.
A=150mm Connect beforehand the indoor/outdoor electric cable, and then
35mm
Ø70mm
Correct Incorrect
When connecting the cable after installing the indoor unit
1. Insert from outside the room cable into left side of the wall
Lean Damage of Àare Crack Partial Too outside
hole, in which the pipe has already existed.
2. Pull out the cable on the front side, and connect the cable
making a loop. On Drainage
7.Installation
Installation Manual of Room Air Conditioner
EUROPEAN REGULATIONS IMPORTANT INFORMATION REGA-
CONFORMITY FOR THE MODELS RDING THE REFRIGERANT USED
CE Contains fluorinated greenhouse gases
covered by the Kyoto Protocol A
All the products are in conformity with the following
European provision: R410A 1= kg
B
- Low Voltage Directive 73/23/EEC
2 2= kg
- Low Voltage Directive 2006/95/EC C
-Electomagnetic CompatibilitY 89/336/EEC 1
-Electomagnetic CompatibilitY 2004/108/EC 1+2= kg
D
ROHS F E
The products are fulfilled with the requirements in the
directive 2002/95/EEC of the European parliament and of This product contains fluorinated greenhouse gases covered
by the Kyoto Protocol. Do not vent into the atmosphere.
council on the Restriction of the use of Certain Hazardous
Substances in Electrical and Electronic Equipment (EU Refrigerant type:R410A
RoHS Directive) GWP* value:1975
GWP=global warming potential
WEEE
Please fill in with indelible ink,
In accordance with the directive 2002/96/CE of the European •1 the factory refrigerant charge of the product
parliament, herewith we inform the consumer about the dis- •2 the additional refrigerant amount charged in the field
posal requirements of the electrical and electronic products. and
DISPOSAL REQUIREMENTS: • 1+2 the total refrigerant charge
on the refrigerant charge label supplied with the product.
Your air conditioning product is marked with this The filled out label must be adhered in the proximity of the
symbol.This means that electrical and electronic product charging port (e.g. onto the inside of the stop value
products shall not be mixed with unsorted cover).
household waste. Do not try to dismantle the A contains fluorinated greenhouse gases covered by the
system yourself : the dismantling of the air Kyoto Protocol
conditioning system,treatment of the refrigerant, of oil and of B factory refrigerant charge of the product: see unit name
other part must be done by a qualified installer in accordance plate
with relevant local and national legislation. Air conditioners C additional refrigerant amount charged in the field
must be treated at a specialized treatment facility for reuse, D total refrigerant charge
recycling and recovery. By ensuring this product is disposed E outdoor unit
of correctly, you will help to prevent potential negative cons- F refrigerant cylinder and manifold for charging
equences for the environment and humen health. Please
contact the installer or local authority for more information.
Battery must be removed from the remote controller and dis-
posed of separately in accordance with relevant local and
nationl legislation.
Left Rear A
right
Right
C
Below
more than
20cm
more than 20cm Fixing of outdoor unit
ƽ Fix the unit to concrete or block
ƽ The marks from A to with bolts (10mm) and nuts ¿rmly
G in the ¿gure are the
and horizontally.
parts numbers.
ƽ When ¿tting the unit to wall
ƽ The distance between
the indoor unit and the D surface, roof or rooftop, ¿x
Àoor should be more a supporter surely with nails
than 2m. or wires in consideration of
E
earthquake and strong wind.
more than 60cm ƽ If vibration may affect the
house, ¿x the unit by attaching a
vibration-proof mat.
AIR OUTLET
AIR INLET
CONNECTING PIPING AND ELECTRICAL WIRING
4 DRAIN HOSE
Compressor(Inside of Unit)
ƽ The above indoor and outdoor units’ picture is just for your reference.
Please be subject to the actual product purchased.
Safety Precautions
WARNING
CAUTION
Safety Precautions
Safety Precautions
Precautions for Handing Units for with R410A
Safety Precautions
Installation Procedure
NO
Air outlet
Wind direction
Cushion rubber
4.Installation dimension(Unit:mm)
Model W D H L1 L2 L3
Power Wiring 1U09BS2ERA
Terminal 1U12BS2ERA
Power Wiring 1U18EN2ERA
Distribution
Installation Procedure
1.
1U09BS2ERA
1U12BS2ERA
1U18EN2ERA
2. Connection of pipes
ƽ To bend a pipe, give the roundness as large as possible not to crush the pipe ,
and the bending radius should be 30 to 40 mm or longer.
ƽ Connecting the pipe of gas side ¿rst makes working easier.
ƽ The connection pipe is specialized for R410A.
Half union Flare nut Forced fastening without careful centering may
damage the threads and cause a leakage of gas.
Be careful that matters, such as wastes of sands,water,, etc. shall not enter the pipe.
CAUTION
The standard pipe length is C m. If it is over D m, the function of the unit will be affected. If the pipe has
to be lengthened, the refrigerant should be charged, according to E g/m. But the charge of refrigerant
must be conducted by professional air conditioner engineer. Before adding additional refrigerant,
perform air purging from the refrigerant pipes and indoor unit using a vacuum pump,then charge
additional refrigerant.
Outdoor unit
Ɣ Max.Elevation: Amax
Outdoor unit Ɣ In case the elevation A is more
than 5m, oil trap shoud be
installed every 5~7
B Oil trap Ɣ Max. Length: Bmax
Ɣ In case the pipe length B is
Indoor unit more thanDm, the refrigerant
A
should be charged, according
to E g/m.
(e.g.1U18EN2ERA)
1U09BS2ERA
1U12BS2ERA
1U18EN2ERA
T 25A/250V.
Connecting wiring 2 2
4G0.75mm 4G0.75mm
1(N ) 2 (L) 3 (C )
{
L
POWER 3G1.5mm2
N
POWER
Power cable 3G2.5mm2
Outdoor Unit
1
2
4
5 15
6
8 110
9
10
11 Suction temperature sensor failure When the The wiring of compressor is wrong or
the connection is poor
12
13
15
m 15
17
18
19
25
25
25
8.Service Diagnosis
8.1 Caution for Diagnosis
The operation lamp flashes when any of the following errors is detected.
1.When a protection device of the indoor or outdoor unit is activated or when the thermistor malfunctions,
disabling equipment operation.
2.When a signal transmission error occurs between the indoor and outdoor units.In either case, conduct the
diagnostic procedure described in the following pages.
Large operating Check the installation Check to make sure that the required spaces for
noise and condition. installation (specified in the Technical Guide, etc.) are
vibrations provided.
Code indication
Indoor
Outdoor Reference
displaying fault description
(LED1 flash Page
panel code
times)
indication
Indoor and Communication fault between indoor and
E7 15 Page .76
Outdoor outdoor units
E1 -- Room temperature sensor failure Page .67
Indoor Malfunction E2 -- Heat-exchange sensor failure Page .67
E4 -- Indoor EEPROM error Page .68
E14 -- Indoor fan motor malfunction Page .69
F12 1 Outdoor EEPROM error Page .68
F1 2 The protection of IPM Page .71
Outdoor 3 Overcurrent protection of AC electricity
F22 Page .72
Malfunction for the outdoor model
Communication fault between the IPM and
F3 4 Page 73
outdoor PCB
F19 6 Power voltage is too high or low Page .74
F27 7 Compressor is lockrotor or stopt momentary -------
F4 8 Overheat protection for exhaust temperature Page .75
F8 9 Outdoor fan motor malfunction Page .72
F21 10 Frost-removing temperature sensor failure Page .74
F7 11 Suction temperature sensor failure Page .69
F6 12 Ambient temperature sensor failure Page .74
F25 13 Exhaust temperature sensor failure Page .74
F11 18 deviate from the normal for the compressor Page .78
Troubleshooting * Caution Be sure to turn off power switch before connect or disconnect connector, or
else parts damage may be occurred.
NO
Yes
NO
Yes
Replace the indoor unit PCB
Method of The Data detected by the EEPROM are used to determine MCU
Malfunction
Detection
Malfunction when the data of EEPROM is error or the EEPROM is damaged
Decision
Conditions
Troubleshooting * Caution Be sure to turn off power switch before connect or disconnect connector, or
parts damage may be occurred.
Method of The rotation speed detected by the Hall IC during fan motor operation is used to determine
Malfunction abnormal fan motor operation
Detection
Malfunction when the detected rotation feedback singal don’t receiced in 2 minutes
Decision
Conditions
Supposed Ŷ Operation halt due to breaking of wire inside the fan motor .
Causes Ŷ Fan motor overheat protection
Ŷ Operation halt due to breaking of the fan motor lead wires
Ŷ Detection error due to faulty indoor unit PCB
Troubleshooting * Caution Be sure to turn off power switch before connect or disconnect connector, or
else parts damage may be occurred.
<HV
Yes
Measure whether there is voltage pulse(0-5VDC)
<HV
check whether motor can run between the positions middle wire and black wire
Is it ok?
12
12
<HV
the indoor motor is damaged and need replace
the indoor pcb is damaged and need replace
Yes
run
Yes
Is it normal?
Is it normal?
N0 Yes
N0
the motor of the outdoor unit is damaged The mainboard of the outdoor unit is
Method of IPM protection is detected by checking the compressor running condition and so on
Malfunction
Detection
Troubleshooting * Caution Be sure to turn off power switch before connect or disconnect connector, or
else parts damage may be occurred.
Malfunction unsolved
NO
1ǃThe system may have been over or under charged with gas, which can be judged through the pressure of the
measuring system.
2ǃThe shaft of compressor is seized and the compressor needs replacing.
Troubleshooting * Caution Be sure to turn off power switch before connect or disconnect connector, or
parts damage may be occurred.
NO
NO
NO
Method of Communication is detected by checking the IPM module and the outdoor PCB
Malfunction
Detection
Troubleshooting * Caution Be sure to turn off power switch before connect or disconnect connector, or
else parts damage may be occurred.
Malfunction unsolved
YES
NO
Method of An abnormal voltage rise or fall is detected by checking the specified voltage detection circuit.
Malfunction
Detection
Malfunction An voltage signal is fed from the voltage detection circuit to the microcomputer
Decision
Conditions
Troubleshooting * Caution Be sure to turn off power switch before connect or disconnect connector, or else
parts damage may be occurred.
Yes
Maybe there is some disturbance
Is it ok?
No
>150 V or <390V?
NO
Yes
Change the IPM module
~230 is ok?
NO
Method of The exhaust temperature control is checked with the temperature being detected
Malfunction by the exhaust pipe thermistor
Detection
Malfunction when the compressor discharge temperature is above 110ć
Decision
Conditions
Supposed Ŷ Electronic expansion valve defective
Causes Ŷ Faulty thermistor
Ŷ Faulty PCB
Troubleshooting * Caution Be sure to turn off power switch before connect or disconnect connector, or
else parts damage may be occurred.
Electrify the machine again and turn it on with the remote controller,
then measure the temperature at the exhaust temperature sensor of
the compressor on the outdoor unit
NO
YES
The sensor is damaged. Replace the sensor
the results deviate
with a new one.
much?
NO
Method of Communication is detected by checking the indoor PCB and the outdoor PCB
Malfunction
Detection
Troubleshooting * Caution Be sure to turn off power switch before connect or disconnect connector, or
else parts damage may be occurred.
NO
YES
Yes
˄A˅
˄A˅
Yes
Check the indoor mainboard
No multimeter.
YES
Method of The position of the compressor rotor can not detected normally
Malfunction
Detection
Troubleshooting * Caution Be sure to turn off power switch before connect or disconnect connector, or parts
damage may be occurred.
YES
Malfunction unsolved
Method of High work-intense control is activated in the heating mode if the temperature
Malfunction being sensed by the heat exchanger thermistor exceeds the limit.
Detection
Malfunction Activated when the temperature being sensed by the heat exchanger
Decision rises above 65ć twices in 30 minutes.
Conditions
Troubleshooting * Caution Be sure to turn off power switch before connect or disconnect connector, or
else parts damage may be occurred.
NO
YES
the indoor unit blows poorly 1) Clean the filters
due to blocked filters or poor 2) Reinstall the fan.
condition of the fan?
NO
Removal of indoorunit
two
HOOKS
three
flap
flap
flap
flap
Remove the
2
Remove the
4
10.Wiring Diagrams
10.1 INDOOR UNIT
,1'22581,7',$*5$0
5
&21
: 5
%
<* &21
&1
5
$1,21 &21
*(1(5$725 5 &21
&21
%
&21
&1 &1
&21 '&)$102725
&21 &21
&21
&1 $0%,(177(036(1625
&1 3,3,1*7(036(1625
&21
6: E M E R G E N R Y
6:
S W IT C H
&21 7$9$&
&21 &1
<*
<*
',63/$<%2$5'
: % 5
1 / &
10.2.Outdoor unit
287'225:,5,1*',$*5$0
:$51,1*
02'8/(%2$5'
CN6 &$87,21
CN9 CN8 '21
7728&+&$3$&,725(9(1$)7(5
3/8*2))'$1*(52)(/(&75,&6+2&.
AC-N AC-L 5 : % 7KHFDSDFLWRUUHWDLQVKLJK
CN11 CN10 CN1 YROWDJHHYHQDIWHUWKHSOXJRII
CN7 : 9 8 )RU\RXUVDIHW\EHVXUHWRZDLW
CN5 CN4 CN3CN 2 DWOHDVWPLQXWHVDIWHUSOXJ
3)&5($&725 RIIDQGXVHDWHVWHUWRFRQILUP
WKHYROWDJHEHWZHHQFRQQHFWRU3
%/ 25 DQG1RQPRGXOHERDUGLVOHVV
WKDQ'&9EHIRUHVWDUW
: % VHUYLFLQJ
WRGRXEOHZD\DLU : CN26
H[FKDQJHPRWRU CN1 CN3 CN22
% PE
CN2 CN24
CN23
TO INDOOR UNIT
'&)$102725
CN4
&1
&1 &1
32:(5 2YHUSUHVVXUHRU2YHUKHDW
SURWHFWLRQIRUWKHFRPSUHVVRU
3RZHUYROWDJHLVWRRKLJKRUORZ
2YHUKHDWSURWHFWLRQIRU
H[KDXVWWHPSHUDWXUH
BL BL )URVWUHPRYLQJWHPSHUDWXUH
$&)$102725
AMBIENT TEMP.SENSOR
WRVLQJOHZD\ VHQVRUIDLOXUH
SUCTION TEMP.SENSOR
&2035(6625',6&+$5*(
7(036(1625
DLUH[FKDQJHPRWRU $PELHQWWHPSHUDWXUHVHQVRUIDLOXUH
(/(&75,&
(OHFWULF (;3$16,219$/9( ([KDXVWWHPSHUDWXUHVHQVRUIDLOXUH
'HYLDWHIURPWKHQRUPDO
7(036(1625
+HDWLQJ&DEOH
IRUWKHFRPSUHVVRU
'()5267
:$<9$/9(
%˖%/$&. :˖:+,7( /RRSRIWKHVWDWLRQGHWHFWHUURU
5˖5(' 2YHUFXUUHQWRIWKHFRPSUHVVRU
<*˖<(//2:*5((1 Remark ˖the dotted parts are
2YHUFXUUHQWSURWHFWLRQIRU
%/˖%/8( 25˖25$1*( optional for different unit. VLQJOHSKDVHRIWKHFRPSUHVVRU
11.Circuit Diagrams
11.1.INDOOR UNIT
1 2 3 4
10K
10K
10K
P1 DIGL R6 100ƻ
1 +5V 1 COM3
notice2˖ SW1,SW1', CN48 choose one to use DIGH R16 E7
2 C28 C20 C2 100ƻ/560ƻ 2 COM2
+5V
R8
3
R37
R96
R10 notice1˖ R54,R63,R85,R86 TJC8-02 0.1uF 0.1uF 0.1uF 100uF-16V-105?
10K R11 used for different display boardDŽ R103 20K 4 GND
RST 4 5 SER R18 100ƻ/560ƻ
+5V 3 R102
6 10K R104 2K BM R17 100ƻ/560ƻ 5 SER
2K RCK 6 RCK
C1 R85 10K 2 7 R69 2K 25/35 SRCK R21 100ƻ/560ƻ
R23 7 SRCK
0.1uF 1 8 R7 2K A/B IR
10K 8 IR
R54 10K 100uF-16V-105? R31 1K
+5V E2 C6 SW2 10K
C19 R62
R63 R94 10K IC2 1nF +5V +5V
TVS1 10K 1 0.1uF 64SCL
R86 10K P3_3/SSI P3_5/SCL/SSCK 4
+5V 2 63SDA ROOM R24 1K
C P3_4/SDA/SCS P3_7/SSO 3 C
ROOMPIPE
HTVSB7.0CA-100
R51 10K
25 40
5 B
4 C
3 D
2
1
E15 P1_6/CLK0 P6_4/RXD2 COMM_RX 10K CN11'
CON15 NET_RX 26 39R40 step motor
A
200±10mm -R P1-5/RXD0(TRAIO)/INT1
P6_5/(CLK1)/CLK2 Ǽ3ˉR
IC8
NET_TX 27 38REMOTE_RX +12V
12V
+12V 47uF-50V-105? SWITCH P1_4/TXD0 P6_7/INT3/RXD1
28 P8_6 P6_6/INT2/TXD1 37REMOTE_TX 1
A1 B1
16
R77 10K
29 36IR USTEP_D R70 1K 2 15 D1
R78 10K P8_5/TRFO12 P4_5/INT0 A2 B2
30 P8_4/TRFO11 P6_0/TREO 35FK USTEP_C R72 1K 3
A3 B3
14 C2
R35 R73 R34 1K R45 10K
+5V
REMOTE_RX 31 P8_3/TRFO10/TRF1 P8_1/TRFO00 34R75 10K USTEP_B R76 1K 4
A4 B4
13 B3
10K R44 10K
32 33R41 10K USTEP_A R79 1K 5 12 A4
10K P8_2/TRFO02 P8_2/TRFO01 A5 B5
CN36 C13 REMOTE_TX BUZZ R80 1K 6 11 12V
R38 10nF A6 B6 5
2 R5F212A7SNFA FLZ R81 1K 7
A7 B7
10
N1 8 9 CN11+12V
1 10K 2SC2412K GND +12 R82
+5V
R43 ULN2003A +12V
R83 220ƻ
27ƻ C15 R50
10K
+12V CON9 0.1uF 2K BUZZ1
NET_TX
NET_RX
1
R56 N4
+5V R74 K3
4 GND 10K 2SC2412K 892N-1AC-C 1 R
4.7K D6 D4 PKM13EPY-4002
3 TX
2
2
R66 10K CON8
5267-04A 220V_L
1 2 3 4
1 2 3 4
VCC
CON003 R009 ZD003 E007
200±10mm -B E006 10uF- 25V- 105?
D002 1. 5K- 1/ 4W 1N4746A(18V-1W)
D 1N5399 10uF- 25V- 105? D
NTC001 310V
4. 7nF- 275VAC
C003 C008 C005
SCK084R72 +12V
CON001 220VL D001 1N5399 R001 1 T001 7 L7805CV˄ 1. 5A˅ H- 25*15
RED 2 6 2. 2nF- 250V 2. 2nF- 250V
47K- 2W I C001
R002
D003 BCK-6-FE1901H 3
BLACK 220VN 0.1uF-275VAC D005 C007 +12V
100uF- 450V- 105? D007 C006 2
2
CON004 IC003
SWITCH POWER SUPPIAY 200±10mm -R ZD002
E002 1N4742A(12V-1W)
R004 22uF- 25V- 105?
C ICE2A265 C
I C002 TLP421
4 1
1 2
2
3 34
4
ZD001
C A
18V-1W
1
R007
100K- 1/ 4W
3 E K 2
27Ω - 1/ 4W
C004
0. 1uF/ 50V
R005 E003
B RTB-1.5-2P B
220V_L CN30
L FUSE1 +5V
LB2271(32mH-0.35A)2.2nF-250VAC
4 2 1 1
1 CY1 2
CON1 1 R13
4 3
T3.15A-250VAC 330ȍ
B LX1 IC4 R12 D11
~220VAC RV1
1 1 4 100K-1/4W R14
CX1 R90 A C 220V_L
2
CY2 CON13
COMM_TX COMM_TX 2 3 1N4007 47K-2W
1 2.2nF-250VAC 4. 7K N5 K E R15
CON2
TVR14561* 0.1uF-275VAC SS8050LT1H
TLP851/PC851 C8 47K-2W
R91 IC6 E4
W 0.1uF-50V ZD1
220V-N
+5V 4. 7K 4 C A 1 1N4746A(18V-1W)
R20 100uF-50V-105? 220V-N
COMM_RX COMM_RX 3 E K 2
CN002 C17 E1 1K R22 CY3
+5V 4 220uF-25V-105 ? R19 TLP421 2K-1/4W 2.2nF-250VAC
C9
GND 3 0.1uF 1nF 10K
D12 CON7
A +12V 2 +12V R26 A
COMM 1
GND 1 C4 E6
1N4007 2K-2W
80±5mm -R/B-4P 0.1uF
220uF-25V-105 ? communication
1 2 3 4
11.2.OUTDOORUNIT
11.2.1Control Bard Circuit Diagrams
COM heater
AC-L AC-N AC-N OUT AC-L OUT Four -Way Comment:
CN25 CN11 CN27 CN36 Three-speed AC Fan Two-speed AC Fan CN14 CN15
CN5 CN6 CN8 CN9
3
2
1
1
1
2
1
1
2
9
8
7
6
5
4
3
2
1
5
4
3
2
1
1
CN10
CN12
CN13
CN2 FUSE1 PTC1 COM ST W B White BlackCOM L H C C COM L H C C
J24 J25 J26 J27
Black 1 L1 L2 2U/450V
T25A 250VAC 400N R12 FUSE2 C1
AC-L RV1 R1 CX1 R2 CX2 CX3 100/1W CX4 T1A/250V
CN1 1M 1M 225/275V 103/275V 2SC2412K
S14K350 225/275V 225/275V N4
8MH/10A 8MH/10A J32
White 1
J28 J29 J30 J31 K1
AC-N K5 K3 K4 K6 K2
RV2 RV3 R88
CY1
CY2
CY3
CY4
CY5
CY6
CN3 SA1 +12V
S14K350 S14K350 10K R87
Yellow/Green 1 J34 4.7K
D6
PE RA-362M 12V-5A-892H(N)-1AC-C 12V-5A-892H(N)-1AC-C 12V-5A-892-1CC-C LL4148 CN17
472/250V/275V
472/250V/275V
103/250V/275V
103/250V/275V
472/250V/275V
472/250V/275V
12V-25A-891P-1A-C 12V-5A-892H(N)-1AC-C 12V-5A-892H(N)-1AC-C +5V
+5V +5V 3
+12V+12V J6 J33 D11 D5 2
N P 2SC2412K 2SC2412K LL4148 LL4148
J7 J15 N5 N3 E11 1
P N
TQ(White)
+15V+15V J23 J16
R82
4.7U/16V
47K/1%
J13 J4 J10 C23 C24 C25 C26
J14 J37 J8 CN18
J12 J38 J3 R89 R85 R84 104/50V 104/50V
104/50V 104/50V 3
CN21 +15V +5V R92 0 10K 10K 4.7K 2
Comment: 2SC2412K E12
310V CX7 ZD2 R34 1K 4 IC8 1 R38 N1 R93 0 +5V 1
R80
1 4.7U/16V
XQ(Red)
0 C10
20K/1%
104/275V 10V/0.5W 62
2 0V R13 330/1W 3 2 330
R94
0 61 VCC TX 51 52
1K R83 R91
CN19
3 15V ZD3 R99 1K R81
5.1V/0.5W PC817A 104/50V 59 VREF XQ 53
1K R79 10K
4 䇗䗳 R39 R40 5.1K/1% J36 13 AVSS CS 54 2
5 10K 1K R77
1 IC9 36 DC-FANSPEED HW 46 1
Ⳉ⌕亢ᴎ
ড作 103/50V 4 E13
6 R33 E9
41 DC Com OUT Fre Light 31
FAN PG Adjust
CS(White)
R78 R76
J9 R41 1K J5 4.7U/16V
20K/1% 20K/1%
C15 2.2K 47U/25V C14 Indoor Fault CN20
(ⱑ ) 2 3 38 55 R75 2K
37 Indoor
102/50V Com IN SW-1 56
R36 1K R35 1K PC817A J22 3
45 PC COM SW-2 60 4.7K E14 2
R37 330 R102 28 NC HEAT-2 47
R86 4.7U/16V 1
Terminal Pro
Fan/E-Valve select
HW(Yellow)
0 27 29
MODULE COMOUT SDA C19
LED1
26 30
3 IC11 2 N6 MODULE COM IN SCL 104/50V
ERROR
CN4 J21 +5V Comment: 2SC2412K 44 NC H/L FAN SPEED 42 J2
R100 24
R3 D1 4 1 R42
4.7K 50 TEST-EN FAN 57 J1 CN31
㑶 1 VSS 4-WAY
58
1
CN7 2K/2W TLP851/PC851 330 23 63
COM 1N4007 R43 R101 COOL-EN HEAT-1 2
GND +5V 22 64
1 5V J18 4.7K 6 HEAT-EN PTC 1 +5V 3
2 RST 0 RESET E-VALVE-D 4
102/50V
102/50V
10K/1%
10K/1%
9 2
3 MODE R98 R4 1 IC10 4 R104
7 XIN E-VALVE-C 4
SW TEST(BLUE)
4 10K 2K XOUT E-VALVE-B
CY7
ⱑ 0 8 5
CY10
R73
C21
R74
C22
2 3 R44 J20 48 VSS E-VALVE-A 3
222/250VAC
222/250VAC
R66 1K 1
4.7K
Comment: 102/50V VCC NC 40 R67 1K 2
16
14 NC 39 15
NC R68 1K 3 CN16
15 NC
NC 35
14
R69 1K 4 D 1
17 NC 34 13
NC R70 1K C 2
CN32 18 NC 33 5 12
+5V NC J39 R71 1K B
CN23 TEST/SS 19 NC
NC 32
6 11 3
5V R49 R48 1 GND IC5 J40 R72 1K 7 A 4
20 NC 16 10
3 10K 10K 2 +5V 21 NC R5F212A8SNFA NC
2 COM +5V +5V
R61 NC 12 GND12V 5
GND J17 25 NC 11 6
1 NC C13
E-valve(White)
1K
1K
1K
1K
PCJ35 SW1 5
GND 4
C11
102/50V COOL 2 3 7
CN33 4 R64 GND GND 1
R46 5 TEST/SS 10K R65 8 VCC GND
10K
White2 0
FUCTION TEST(White) C12
1 +5V 104/50V
1 3
R19
47
C3
P
CY8 R22
470U/25V Comment: 100U/16V
104/50V
472/1KV 104/50V 1K/0.5W
R14
3 9
100K/2W
D10
CX5 ER106 +5VD
104/275V
D7 L3
ZD1 6 MBR1100\SB1100 20UH/1A
IN5948B R24 R29 CY9
C7
104/50V
E5 E6
47 100U/16V
5.1K/1%
ADJ HV
10K
2 FB NC 7 R18 47
C2 +15V CN22
R90 0
3 6 102/100V 1
CS VCC
D9 2
J11 4 GNDDRV
5 4 MUR115\MUR130\ER106 3
E4 C6 R17
NCP1200P100 330/1W ഫ ᵓ ⬉ ⑤ (㪱 )
470U/25V 104/50V
R26 R15 5
1K 15 E3
R27 M1 22U/25V R32
10K IRFUC20 5.1K/1%
IC2 PC817A IC3
C4 4 1 C5 TL431C
103/50V R30 R31 104/50V
1K 1K
R16 2/1W 3 2
1 2 3 4
L
5.2MH/15A
CN7 CN6 CN1 24 P
2
LI LO D207 P CN2
U 23 U
FFA30U60DN
PM1
D PS21964-AT/AST/PS219A4-ASTX D
CN8 1 3 IC8 V 22 CN3
AC-L C405 C404 C406 V
104/275V SGH40N60UF 680U/400V*2 104/275V
474/630VDC
R215
BG1 CN4
4
D25BX60B 10K W 21 W
RS1 RS2 20
N N
CN9 0.015/5W CN5 0.02/5W
AC-N
VUFB
VVFB
VWFB
UP
VP
WP
VP1
VNC
UN
VN
WN
VN1
FO
CIN
VNC
VNO
R214 R222,R225খ᭄⬅य़㓽ᴎ䗔⺕⬉⌕䅵ㅫ㗠ᅮ
100 5V 15V
5V 15V R225 4.22K 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
2 8 5V
IC7 6 D206
1K
1K
R217
330
R216 C204 104 IC5
10 R218 82 8
6
223
C012 C502 IC5
C205
104 100U/25V 7 HA17393AF
R221 140 R220 82 5 R213 100
1
TR1 4 HA17393AF 15V
R230 D203
MMBT9013 C207 C208 C203
104 104 104 10 US1M C022
C C032 C412 103 C
104 22U/25V R008
D202 5V
4.7K R231
4.7K C003 C002
US1M
5V C034 C411 104 104 C006
R208
6.8K 104 22U/25V 5V 474
D201 C004
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
R224 R011 R212 104
4.7K 4.7K 9.1K 2 8 R207 1K 6 US1M 20
IC6 IC6 C036 C410 41
1 7 R009 4.7K 42 19
R209 1K 104 22U/25V
C201 3 5 43 18
44 17
104 R211 4 HA1630D06 R210 6.8K
HA1630D06
16
5V 45
1K 1 8 46 15
2 IC3 7 R005 4.7K R006 100 47 14
3 6 C020 48 13
4 24C04 5 102 49 12
R017 4.7K C019 50 IC1 11C001
5V 5V 103 51 10 104
R202 SH7046 9
R010 52
6.2K 53 8
R205 4.7K 54 7 C015
1K 8 R201 1K 15V C028
2 6 R007 4.7K 55 6 102
130KR226
C011 5V 6
100U/16V 104 TXD
⬉⑤(㪱) 5
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
5V RXD
4 MD1
3
D205
LL4148
5V 2 5V
C008
474
PC2 R012 1 GND
C030
471
C029
471
130KR228
C007
474
4.7K R003
4.7K R001
4.7K R002
4.7K R004
R019
R015 4.7K
471
4.7K X1 10M
C009
330 PC817A R018 4.7K
CN11 D204
4.22K R229
1 2 3
Sincere Forever