Documente Academic
Documente Profesional
Documente Cultură
Some manufacturers stamp the date, month and year on the base of the item. From this, the life of the
crockery can be determined with some accuracy. Crockery that is produced as being suitable for the
foodservice industry is often referred to as ‘hotelware’. Manufactures also tend to give trade names to
their hotelware to indicate strength or durability. Some examples of these names are:
l Vitreous l Vitrex
l Vitresso l Vitrified
l Vitrock l Steelite.
Ironstone
Foodservice crockery
There are various classifications of foodservice crockery. Although referred to as crockery here (and
throughout the book), all glazed tableware was traditionally referred to as china. Items include:
Types of crockery
Bone china
This very fine, hard china is expensive. Decorations are only found under the glaze. It can be made to
thicker specifications for hotel use. The price of bone china puts it out of reach of the majority of
everyday caterers and only a few of the top-class hotels and restaurants use it. Metalised bone china
has been developed specially for the hospitality industry. It contains added metallic oxides to make it
much stronger than bone china.
Hotel earthenware
Vitrified (or vitreous) earthenware is produced in the United Kingdom in vast quantities. It is the
cheapest but least durable hotelware although it is much stronger than regular domestic earthenware.
There is a standard range of designs and patterns in varying colours.
Domestic weight earthenware is lighter and thinner than hotel earthenware (or vitrified hotelware).
Because of its short life, lack of strength and possible high breakage rate it is not regarded as suitable
for commercial use.
Stoneware
This is a natural ceramic material traditionally made in the United Kingdom and fired at a very high
temperature, about 1,200 °C–1,315 °C (2,200 °F). It is shaped by traditional handcrafting techniques so
there are a wide variety of shapes and finishes available, from matt to a high gloss glaze. It is non-
porous and extremely durable with high thermal and shock resistance. The price is slightly higher than
earthenware due to its long-life guarantee.
72
3.9 Crockery
Porcelain
This is of a different composition with a semi-translucent body, normally cream/grey, and has a high
resistance to chipping.
Crockery sizes
A wide range of crockery items are available (see Figure 3.9(a)) and their exact sizes will vary
according to the manufacturer and the design produced. As a guide, the sizes are as follows:
l Side plate: 15 cm (6 in) diameter
l Sweet plate: 18 cm (7 in) diameter
l Fish plate: 20 cm (8 in) diameter
l Soup plate: 20 cm (8 in) diameter
l Joint plate: 25 cm (10 in) diameter
l Cereal/sweet bowl: 13 cm (5 in) diameter
l Breakfast cup and saucer: 23–28 cl (8–10 fl oz)
l Teacup and saucer: 18.93 cl (6 2⁄3 fl oz)
Coffee cup and saucer (demi-tasse): 9.47 cl (3½ fl oz)
l Teapot: 28.4 cl (½ pint)
56.8 cl (1 pint)
85.2 cl (1½ pint)
113.6 cl (2 pint)
Other items of crockery required include:
l consommé cup and saucer l hot water jug
l soup bowl/cup l coffee pot
l platter (oval plate) l milk jug
l salad crescent l cream jug
l egg cup l hot milk jug
l butter dish l sugar basin
l teapot l salt and pepper pots.
Although crockery has been the traditional medium for presenting and serving food, there is now an
increasing trend to use contemporary styles of glassware instead. Figure 3.9(b) gives examples of both
traditional crockery and also contemporary styled glassware that can be used as alternatives to
crockery.
73
Chapter 3 Food and beverage service areas and equipment
74
3.10 Tableware (flatware, cutlery and hollow-ware)
Storage
Crockery should be stored on shelves in piles of approximately two dozen. Any higher may result in
their toppling down or damage to plates at the bottom of the stack because of the weight bearing down
on them. Crockery should be stored at a convenient height for placing on and removing from the
shelves without fear of accidents occurring. If possible crockery should be kept covered to prevent dust
and germs settling on it.
flatware in the catering trade denotes all forms of spoon and fork, as well as serving flats
cutlery refers to knives and other cutting implements
hollow-ware consists of any other item, apart from flatware and cutlery, for example, teapots, milk
jugs, sugar basins and serving dishes.
Manufacturers produce varied patterns of flatware, hollow-ware and cutlery in a range of prices to suit
all demands. There are also patterns of flatware and cutlery that are scaled down to three-quarters the
normal size specifically for tray service.
Although traditionally flatware included spoons and forks and cutlery referred to knives, the modern
usage of these terms has changed. All spoons, forks and knives used as eating implements are now
referred to as cutlery. The term ‘cutlery’ is therefore used throughout the rest of this book.
The majority of foodservice areas use either plated silverware or stainless steel. Once again, the points
mentioned previously concerning purchasing should be borne in mind. In addition, when purchasing
flatware and cutlery it is important to consider:
the type of menu and service offered
the maximum and average seating capacity
the peak demand period turnover
the washing-up facilities and their turnover.
Figure 3.9 Examples of cutlery (left to right: fish fork, sweet (small) fork, joint fork, fish knife, small (side)
knife, joint knife, coffee spoon, tea spoon, soup spoon, sweet spoon, table (service) spoon).
75
Chapter 3 Food and beverage service areas and equipment
Silver
Manufacturers will often quote 20-, 25- or 30-year plate. This denotes the length of life a manufacturer
may claim for their plate subject to fair or normal usage. The length of life of silver also depends upon
the weight of silver deposited. There are three standard grades of silver plate – full standard plate, triple
plate and quadruple plate.
Method Description
Silver dip Items to be cleaned are completely immersed in dip in a plastic bowl for a very short time,
rinsed in clean water and polished with a tea cloth. This is a very quick method but is hard on
metal if left in dip too long
Burnishing Items to be cleaned are placed in a drum containing ball bearings, soap powder and water.
machine The drum rotates and the tarnish is rubbed off. All items are rinsed in hot water and dried with
a tea cloth
Polvit Items to be cleaned are placed in an enamel or galvanised iron bowl within which is the Polvit
aluminium metal sheet containing holes, together with some soda. At least one piece of silver
needs contact with the Polvit. Boiling water is poured onto the silver being cleaned. A chemical
reaction causes the tarnish to be lifted. After three to four minutes remove silver and rinse in
boiling water. Drain and then polish with a clean, dry tea cloth
A simpler version of this may be used for silver fork tips that have become tarnished. An
aluminium saucepan on the stove, half filled with gently boiling water, can be used to put fork
tips into for a short time. The forks need to touch each other and the side of the saucepan at
the same time for the chemical reaction to take place. This easily removes the tarnishing and is
less harmful to the silver than using silver dip
76
3.10 Tableware (flatware, cutlery and hollow-ware)
Method Description
Plate powder Pink powder is mixed with a little methylated spirit to a smooth paste. The smooth paste is
rubbed well onto the tarnished silver with a clean piece of cloth. The article is left until the
paste has dried which is then rubbed off with a clean cloth. The article must be rinsed well in
very hot water and given a final polish with a clean dry tea cloth. For a design or engraving use
a small toothbrush to brush the paste into the design and a clean toothbrush to remove it. This
method is both time-consuming and messy, but produces very good results.
(Information based on that obtained from the Cutlery and Allied Trades Research
Association (CATRA).)
Stainless steel
Stainless steel tableware is available in a variety of grades. The higher priced designs usually
incorporate alloys of chromium (which makes the metal stainless) and nickel (which gives a fine grain
and lustre). Good British flatware and cutlery is made of 18/8 or 18/10 stainless steel
– this is 18 per cent chromium and 8 per cent nickel. It should be noted however that the harder the
metal used for the cutting edge the more difficult it is for the manufacturer to gain a sharp edge due to
the metal’s hardness.
Stainless steel is finished by different degrees of polishing:
high polish finish
dull polish finish
light grey matt, non-reflective finish.
Stainless steel resists scratching far more than other metals and may therefore be said to be more
hygienic. Although it does not tarnish it can stain. Special cleaning products for stainless steel can be
used to keep stainless steel looking clean and polished, for example there is a commercial powder that
is applied with a wet sponge or cloth and rubbed on the surface before being rinsed off.
Table knives require attention to keep the sharpness of the blade. Table knives are normally sharpened,
according to the recommendations of the Cutlery and Allied Trades Research Association (CATRA),
to approximately a 60 ° edge angle (compared to the 30 ° for the Chef’s knife). Traditionally table
knives were sharpened with a plain edge (that is, without serrations, scallops or indentations on the
edge). Today many knives found in the foodservice industry have much thicker blades and the cutting
edges are serrated. There is a well-established myth that for a table knife to work well it must be
serrated. However, a serrated knife simply tears the meat piece rather than cutting it.
77
Chapter 3 Food and beverage service areas and equipment
Equipment Use
78
3.11 Glassware
Equipment Use
Storage
In larger establishments the silver room (also known as the plate room) is a separate service area in
which a complete stock of tableware required for the service of meals, together with a slight surplus
stock in case of emergency, is stored. Tableware for banqueting service may be of a different design
and kept specifically for that purpose within the banqueting department. In smaller establishments it is
often combined with the wash-up area.
Large tableware items such as flats, salvers, soup tureens and cloches are often stored on shelves, with
all the flats of one size together and so on. All shelves should be labelled showing where each different
item goes. This makes it easier for control purposes and for stacking; heavier items should go on lower
shelves and smaller and lighter items on higher shelves as this helps to prevent accidents. All
tableware, together with the smaller items such as cruets, butter dishes, special equipment, table
numbers and menu holders, can be stored in drawers lined with green baize. This helps to prevent noise
and stops the various items sliding about and scratching when in the drawer.
Theoretically all tableware should be stored in a room or cupboard that can be locked, since it
constitutes a large part of the capital investment of the foodservice operation. Cutlery may be stored in
cutlery trolleys or trays ready for use, which can also be locked in a store.
Staffing
For large operations there may be a head plate person with a number of staff under them. In smaller
establishments duties are often combined with the wash-up. It would then be the duty of either the
washing-up staff or the waiting staff to ensure that all the service tableware is kept clean.
3.11 Glassware
Well-designed glassware combines elegance, strength and stability, and should be fine rimmed and of
clear glass. All glassware should be clean and well-polished.
Glassware contributes to the appearance of the table and the overall attraction of the service area. There
are many standard patterns available to the foodservice operator. Most manufacturers now supply hotel
glassware in standard sizes for convenience of ordering, availability and quick delivery. Modern
drinking glasses take many new forms and shapes, although all are primarily designed to meet the
needs of the range of drinks offered. Examples of drinking glasses and their use are shown in Figure
3.12.
79
Chapter 3 Food and beverage service areas and equipment
for sparkling
wines generally Copita (sherry): mainly
and also for Brandy for sherry but also used
Alexander and Kir for sweet wines
Royale Elgin: traditional glass
Paris goblet: in various used for sherry in single
sizes and used for wines, and double measure
waters and beers. Also (Schooner) sizes. Also in
used for Cobblers, Pina smaller version used for
Colada and Green liqueurs
Blazer Port or sherry (dock)
Worthington: for glass: used for both
ports and sherries and
and for Pimms, Coolers also for sweet wines
and long drinks such as
Fruit Cups Lager/pilsner:
Rocks/Old Fashioned sizes used for bottled
glass: also known and draught lager beers
80