Documente Academic
Documente Profesional
Documente Cultură
Important Points
• The cross section of a straight beam remains plane when the beam deforms due to bending. This causes
tensile stress on one portion of the cross section and compressive stress on the other portion. In between
these portions, there exists the neutral axis which is subjected to zero stress.
• Due to the deformation, the longitudinal strain varies linearly from zero at the neutral axis to a maximum
at the outer fibers of the beam. Provided the material is homogeneous and linear elastic, then the stress
also varies in a linear fashion over the cross section.
• The neutral axis passes through the centroid of the cross-sectional area. This result is based on the fact that
the resultant normal force acting on the cross section must be zero.
• The flexure formula is based on the requirement that the resultant internal moment on the cross section is
equal to the moment produced by the normal stress distribution about the neutral axis.
Internal Moment.
• Section the member at the point where the bending or normal stress is to be determined, and obtain the
internal moment M at the section. The centroidal or neutral axis for the cross section must be known, since
M must be calculated about this axis.
• If the absolute maximum bending stress is to be determined, then draw the moment diagram in order to
determine the maximum moment in the member.
Section Property.
• Determine the moment of inertia of the cross-sectional area about the neutral axis. Methods used for its
calculation are discussed in Appendix A, and a table listing values of I for several common shapes is given
on the inside front cover.
Normal Stress.
• Specify the distance y, measured perpendicular to the neutral axis to the point where the normal stress
is to be determined. Then apply the equation s = - My>I, or if the maximum bending stress is to be
calculated, use smax = Mc>I. When substituting the data, make sure the units are consistent.
• The stress acts in a direction such that the force it creates at the point contributes a moment about the
neutral axis that is in the same direction as the internal moment M, Fig. 6–24c. In this manner the stress
distribution acting over the entire cross section can be sketched, or a volume element of the material can
be isolated and used to graphically represent the normal stress acting at the point.
6.4 THE FLEXURE FORMULA 289
EXAMPLE 6.11
Fig. 6–25
16 in.212 kip>in2216 in.2 = 36 kip
1
F =
2
These forces, which form a couple, act in the same direction as the
stresses within each distribution, Fig. 6–25b. Furthermore, they act
through the centroid of each volume, i.e., 2316 in.2 = 4 in. from the
neutral axis of the beam. Hence the distance between them is 8 in. as
shown. The moment of the couple is therefore
EXAMPLE 6.12
The simply supported beam in Fig. 6–26a has the cross-sectional area
shown in Fig. 6–26b. Determine the absolute maximum bending stress
in the beam and draw the stress distribution over the cross section at
this location.
5 kN/m
M (kNm)
22.5
x (m)
3 6
6m
(a) (c)
SOLUTION
Maximum Internal Moment. The maximum internal moment in
20 mm the beam, M = 22.5 kN # m, occurs at the center.
B 150 mm
C Section Property. By reasons of symmetry, the neutral axis passes
6 N A through the centroid C at the midheight of the beam, Fig. 6–26b. The
20 mm
150 mm area is subdivided into the three parts shown, and the moment of
inertia of each part is calculated about the neutral axis using the
20 mm
D
parallel-axis theorem. (See Eq. A–5 of Appendix A.) Choosing to
250 mm
work in meters, we have
I = ©1I + Ad22
(b)
EXAMPLE 6.13
The beam shown in Fig. 6–27a has a cross-sectional area in the shape 2.6 kN
of a channel, Fig. 6–27b. Determine the maximum bending stress that 13 12
occurs in the beam at section a–a. 5
a
SOLUTION
Internal Moment. Here the beam’s support reactions do not have 2m 1m
a
to be determined. Instead, by the method of sections, the segment to the (a)
left of section a–a can be used, Fig. 6–27c. In particular, note that
250 mm
the resultant internal axial force N passes through the centroid of the
_
cross section. Also, realize that the resultant internal moment must be y 59.09 mm 20 mm
calculated about the beam’s neutral axis at section a–a. N A
C 200 mm
To find the location of the neutral axis, the cross-sectional area is
15 mm 15 mm
subdivided into three composite parts as shown in Fig. 6–27b. Using
Eq. A–2 of Appendix A, we have (b)
EXAMPLE 6.14
_
SOLUTION
40 N·m y Without Ribs. Clearly the neutral axis is at the center of the cross
section, Fig. 6–28a, so y = c = 15 mm = 0.015 m. Thus,
(a)
10.060 m210.030 m23 = 0.135110-62 m4
1 1
I = bh3 =
12 12
40 Nm Therefore the maximum normal stress is
Mc 140 N # m210.015 m2
_ smax = = = 4.44 MPa
0.135110-62 m4
30 mm
y Ans.
N I
5 mm With Ribs. From Fig. 6–28b, segmenting the area into the large main
rectangle and the bottom two rectangles (ribs), the location y of the
A
centroid and the neutral axis is determined as follows:
6 10 mm
©yA
10 mm y =
(b) ©A
[0.015 m]10.030 m210.060 m2 + 2[0.0325 m]10.005 m210.010 m2
=
10.03 m210.060 m2 + 210.005 m210.010 m2
Fig. 6–28
= 0.01592 m
This value does not represent c. Instead
c = 0.035 m - 0.01592 m = 0.01908 m
Using the parallel-axis theorem, the moment of inertia about the
neutral axis is
NOTE: This surprising result indicates that the addition of the ribs
to the cross section will increase the normal stress rather than decrease
it, and for this reason they should be omitted.
6.4 THE FLEXURE FORMULA 293
FUNDAMENTAL PROBLEMS
F6–15. If the beam is subjected to a bending moment of F6–18. If the beam is subjected to a bending moment of
M = 20 kN # m, determine the maximum bending stress in M = 10 kN # m, determine the maximum bending stress in
the beam. the beam.
300 mm
200 mm
200 mm 30 mm
20 mm
30 mm 50 mm
20 mm 30 mm
20 mm 150 mm
M
F6–15 M
150 mm
F6–16. If the beam is subjected to a bending moment of
M = 50 kN # m, sketch the bending stress distribution over 50 mm
the beam’s cross section.
30 mm
F6–18 6
300 mm
M
F6–19. If the beam is subjected to a bending moment of
M = 5 kN # m, determine the bending stress developed at
150 mm
point A.
150 mm
F6–16
50 mm
F6–17. If the beam is subjected to a bending moment of 50 mm
M = 50 kN # m, determine the maximum bending stress in
the beam.
150 mm
200 mm
M
25 mm
20 mm 25 mm
300 mm 150 mm
M
20 mm 50 mm
20 mm A
F6–17 F6–19
294 CHAPTER 6 BENDING
PROBLEMS
6–47. A member having the dimensions shown is used 6–50. The channel strut is used as a guide rail for a trolley.
to resist an internal bending moment of M = 90 kN # m. If the maximum moment in the strut is M = 30 N # m,
Determine the maximum stress in the member if the determine the bending stress at points A, B, and C.
moment is applied (a) about the z axis (as shown) (b) about
the y axis. Sketch the stress distribution for each case. 6–51. The channel strut is used as a guide rail for a trolley.
If the allowable bending stress for the material is
sallow = 175 MPa, determine the maximum bending moment
the strut will resist.
50 mm
C
200 mm 5 mm
y 5 mm
B
150 mm
30 mm
M
z 5 mm
x A
5 mm
Prob. 6–47 5 mm 7 mm 10 mm 7 mm
6
Probs. 6–50/51
*6–48. Determine the moment M that will produce a
maximum stress of 10 ksi on the cross section. *6–52. The beam is subjected to a moment M. Determine
•6–49. Determine the maximum tensile and compressive the percentage of this moment that is resisted by the
bending stress in the beam if it is subjected to a moment of stresses acting on both the top and bottom boards, A and B,
M = 4 kip # ft. of the beam.
D 150 mm
B 25 mm
0.5 in.
25 mm 150 mm
Probs. 6–48/49 25 mm Probs. 6–52/53
6.4 THE FLEXURE FORMULA 295
6–54. The beam is made from three boards nailed together 6–58. If the beam is subjected to an internal moment of
as shown. If the moment acting on the cross section is M = 100 kip # ft, determine the maximum tensile and
M = 600 N # m, determine the maximum bending stress in compressive bending stress in the beam.
the beam. Sketch a three-dimensional view of the stress
distribution acting over the cross section. 6–59. If the beam is made of material having an allowable
tensile and compressive stress of (sallow)t = 24 ksi and
6–55. The beam is made from three boards nailed together (sallow)c = 22 ksi, respectively, determine the maximum
as shown. If the moment acting on the cross section is allowable internal moment M that can be applied to the
M = 600 N # m, determine the resultant force the bending beam.
stress produces on the top board.
3 in.
25 mm
3 in.
6 in.
150 mm
M
20 mm
2 in.
200 mm M 600 Nm
1.5 in.
20 mm
B
Mz 16 kipft
B z
M 8 kNm 1 in.
20 mm 14 in. x
50 mm
50 mm 1 in.
6–62. A box beam is constructed from four pieces of •6–65. If the moment acting on the cross section of the
wood, glued together as shown. If the moment acting on the beam is M = 4 kip # ft, determine the maximum bending
cross section is 10 kN # m, determine the stress at points A and stress in the beam. Sketch a three-dimensional view of the
B and show the results acting on volume elements located at stress distribution acting over the cross section.
25 mm
A
250 mm
A
1.5 in.
12 in.
25 mm B
12 in.
M 10 kNm M
Prob. 6–62
1.5 in.
1.5 in.
6–63. Determine the dimension a of a beam having a
square cross section in terms of the radius r of a beam with
a circular cross section if both beams are subjected to the
same internal moment which results in the same maximum
6 bending stress. Probs. 6–65/66
a
r 6–67. The rod is supported by smooth journal bearings
at A and B that only exert vertical reactions on the shaft. If
d = 90 mm, determine the absolute maximum bending
stress in the beam, and sketch the stress distribution acting
over the cross section.
Prob. 6–63
A 12 kN/m
d
B
A B
M 300 lbft
45
3m 1.5 m
•6–69. Two designs for a beam are to be considered. *6–72. The steel beam has the cross-sectional area shown.
Determine which one will support a moment of M = Determine the largest intensity of distributed load w0 that it
150 kN # m with the least amount of bending stress. What is can support so that the maximum bending stress in the
that stress? beam does not exceed smax = 22 ksi.
300 mm 300 mm
30 mm 15 mm
15 mm 30 mm 12 ft 12 ft
(a) (b) 8 in.
B
6 ft 6 ft 6 ft G 1 ft C
A
Prob. 6–70
D
6–71. The axle of the freight car is subjected to wheel 3 ft 5 ft 4 ft
1.75 in.
loadings of 20 kip. If it is supported by two journal bearings at 1 ft
C and D, determine the maximum bending stress developed
at the center of the axle, where the diameter is 5.5 in. 3 in. 1.75 in.
40 mm 25 mm
60 in. A B C D
10 in. 10 in.
20 kip 20 kip
0.75 m 1.5 m 0.75 m
Prob. 6–71 3 kN Prob. 6–75
3 kN
298 CHAPTER 6 BENDING
*6–76. Determine the moment M that must be applied to •6–81. If the reaction of the ballast on the railway tie can be
the beam in order to create a maximum stress of 80 MPa. assumed uniformly distributed over its length as shown,
Also sketch the stress distribution acting over the cross determine the maximum bending stress developed in the tie.
section. The tie has the rectangular cross section with thickness
t = 6 in.
6–82. The reaction of the ballast on the railway tie can be
300 mm assumed uniformly distributed over its length as shown.
20 mm If the wood has an allowable bending stress of sallow =
1.5 ksi, determine the required minimum thickness t of the
rectangular cross sectional area of the tie to the nearest 18 in.
M
15 kip 15 kip
260 mm
30 mm 1.5 ft 5 ft 1.5 ft
12 in.
30 mm
20 mm 30 mm
t
Prob. 6–76
w
•6–77. The steel beam has the cross-sectional area shown.
Determine the largest intensity of distributed load w that it Probs. 6–81/82
can support so that the bending stress does not exceed
smax = 22 ksi. 6–83. Determine the absolute maximum bending stress
in the tubular shaft if di = 160 mm and do = 200 mm.
6 6–78. The steel beam has the cross-sectional area shown.
If w = 5 kip>ft, determine the absolute maximum bending *6–84. The tubular shaft is to have a cross section such
stress in the beam. that its inner diameter and outer diameter are related by
di = 0.8do. Determine these required dimensions if the
allowable bending stress is sallow = 155 MPa.
w w 15 kN/m
60 kN m d
i do
A B
8 ft 8 ft 8 ft
3m 1m
8 in.
Probs. 6–83/84
0.30 in.
0.3 in. 10 in.
6–85. The wood beam has a rectangular cross section in
0.30 in.
the proportion shown. Determine its required dimension b
if the allowable bending stress is sallow = 10 MPa.
Probs. 6–77/78
500 N/m
6–79. If the beam ACB in Prob. 6–9 has a square cross
section, 6 in. by 6 in., determine the absolute maximum
bending stress in the beam. 1.5b
A B
*6–80. If the crane boom ABC in Prob. 6–3 has a b
rectangular cross section with a base of 2.5 in., determine its 2m 2m
required height h to the nearest 14 in. if the allowable bending
stress is sallow = 24 ksi. Prob. 6–85
6.4 THE FLEXURE FORMULA 299
6–86. Determine the absolute maximum bending stress 6–91. Determine the absolute maximum bending stress
in the 2-in.-diameter shaft which is subjected to the in the 80-mm-diameter shaft which is subjected to the
concentrated forces. The journal bearings at A and B only concentrated forces. The journal bearings at A and B only
support vertical forces. support vertical forces.
6–87. Determine the smallest allowable diameter of the *6–92. Determine the smallest allowable diameter of the
shaft which is subjected to the concentrated forces. The shaft which is subjected to the concentrated forces. The
journal bearings at A and B only support vertical forces. journal bearings at A and B only support vertical forces.
The allowable bending stress is sallow = 22 ksi. The allowable bending stress is sallow = 150 MPa.
A B
800 lb
A 600 lb
0.5 m 0.4 m 0.6 m
12 kN
20 kN Probs. 6–91/92
15 in.
B
15 in. •6–93. The man has a mass of 78 kg and stands motionless at
the end of the diving board. If the board has the cross section
30 in. shown, determine the maximum normal strain developed in
the board. The modulus of elasticity for the material is
E = 125 GPa. Assume A is a pin and B is a roller.
Probs. 6–86/87
6
1200 lb
800 lb/ft
Prob. 6–93
B
6–94. The two solid steel rods are bolted together along
A
their length and support the loading shown. Assume the
support at A is a pin and B is a roller. Determine the required
8 ft 8 ft
diameter d of each of the rods if the allowable bending
stress is sallow = 130 MPa.
Prob. 6–88
6–95. Solve Prob. 6–94 if the rods are rotated 90° so that
both rods rest on the supports at A (pin) and B (roller).
80 kN
•6–89. If the compound beam in Prob. 6–42 has a square 20 kN/m
cross section, determine its dimension a if the allowable
bending stress is sallow = 150 MPa.
A
6–90. If the beam in Prob. 6–28 has a rectangular cross
section with a width b and a height h, determine the 2m B
absolute maximum bending stress in the beam. 2m
Probs. 6–94/95
300 CHAPTER 6 BENDING
*6–96. The chair is supported by an arm that is hinged so 6–99. If the beam has a square cross section of 6 in. on
it rotates about the vertical axis at A. If the load on the chair each side, determine the absolute maximum bending stress
is 180 lb and the arm is a hollow tube section having the in the beam.
dimensions shown, determine the maximum bending stress
at section a–a.
180 lb
400 lb/ft
1 in.
a B
A
A 3 in. 2.5 in.
6 ft 6 ft
a
8 in. 0.5 in.
P (in./ in.)
0.02 0.05
Prob. 6–97
w0
6–98. If the beam in Prob. 6–18 has a rectangular cross
section with a width of 8 in. and a height of 16 in., determine
the absolute maximum bending stress in the beam.
9 ft 9 ft
16 in. 9 in.
0.25 in.
0.25 in. 12 in.
0.25 in.
8 in.
6–102. The bolster or main supporting girder of a truck •6–105. If the allowable bending stress for the wood beam
body is subjected to the uniform distributed load. Determine is sallow = 150 psi, determine the required dimension b to
the bending stress at points A and B. the nearest 14 in. of its cross section. Assume the support at A
is a pin and B is a roller.
A B
A B
8 ft 12 ft 3 ft 3 ft 3 ft
F1 F2
2b
0.75 in. 6 in.
b
0.5 in. Probs. 6–105/106
12 in.
A
6–107. A beam is made of a material that has a modulus of
B elasticity in compression different from that given for
0.75 in.
tension. Determine the location c of the neutral axis, and
Prob. 6–102 derive an expression for the maximum tensile stress in the 6
beam having the dimensions shown if it is subjected to the
bending moment M.
h
s c
w Et b
P
0.5 m 1m 0.5 m
Ec
75 mm
150 mm