Sunteți pe pagina 1din 38

FILE NO.

SERVICE MANUAL LED-22XZ11F


PRODUCT CODE No.
1 682 351 40: PAL-B/G (CCIR)
LED-LCD TV NTSC(AV)

INPUT

REFERENCE No.:SM0915203
CONTENTS

Safety precautions………………………………………………………………………..… 3
Alignment instructions …………………………….…….………………………………… 5
Software upgrade instructions .................................................................................. 12
Working principle analysis……………………………….………….…………............... 15
Block diagram…………………………………..………………………………….…………17
IC block diagram………………………………………………………………………..……18
Wiring diagram ……………………………………………………………………………. 21
Troubleshooting flow chart ………………………………………………………………..……
22
Schematic diagram………………………………………………………………………… 25
APPENDIX-A: Assembly list
APPENDIX-B: Exploded View
Assembling the Stand
WALL MOUNTING INSTRUCTIONS
Attention: This service manual is only for service personnel to take reference with. Before
servicing please read the following points carefully.

Safety precautions
1. Instructions
Be sure to switch off the power supply before replacing or welding any components or
inserting/plugging in connection wire. Anti static measures must be taken (throughout the entire
production process!):
a) Do not touch here and there by hand at will;
b) Be sure to use anti static electric iron;
c) It’s necessary for the welder to wear anti static gloves.
Please refer to the part list before replacing components that have special safety requirements.
Do not replace with different components with different specs and type at will.

2. LCD servicing precautions


2.1 Screens are different from one model to another and therefore not interchangeable. Be sure to
use the screen of the original model for replacement.
2.2 The operation voltage of LCD screen is 700-825V. Be sure to take proper measures in
protecting yourself and the machine when testing the system in the course of normal operation or
right after the power is switched off. Please do not touch the circuit or the metal part of the module
that is in operation mode. Relevant operation is possible only one minute after the power is
switched off.
2.3 Do not use any adapter that is not identical with the TV set. Otherwise it will cause fire or
damage to the set.
2.4 Never operate the set or do any installation work in bad environment such as wet bathroom,
laundry, kitchen, or nearby fire source, heating equipment and devices or exposure to sunlight etc.
Otherwise bad effect will result.
2.5 If any foreign substance such as water, liquid, metal slices or other matters happens to fall into
the module, be sure to cut the power off immediately and do not move anything on the module lest
it should cause fire or electric shock due to contact with the high voltage or short circuit.
2.6 Should there be smoke, abnormal smell or sound from the module, please shut the power off
at once. Likewise, if the screen is not working after the power is on or in the course of operation,
the power must be cut off immediately and no more operation is allowed under the same
condition.
2.7 Do not pull out or plug in the connection wire when the module is in operation or just after the
power is off because in this case relatively high voltage still remains in the capacitor of the driving
circuit. Please wait at least one minute before the pulling out or plugging in the connection wire.
2.8 When operating or installing LCD please don’t subject the LCD components to bending,
twisting or extrusion, collision lest mishap should result.
2.9 As most of the circuitry in LCD TV set is composed of CMOS integrated circuits, it’s necessary
to pay attention to anti statics. Before servicing LCD TV make sure to take anti static measure and
ensure full grounding for all the parts that have to be grounded.
2.10 There are lots of connection wires between parts behind the LCD screen. When servicing or
moving the set please take care not to touch or scratch them. Once they are damaged the screen
would be unable to work and no way to get it repaired.
If the connection wires, connections or components fixed by the thermotropic glue need to
disengage when service, please soak the thermotropic glue into the alcohol and then pull them
out in case of dagmage.
2.11 Special care must be taken in transporting or handling it. Exquisite shock vibration may lead
to breakage of screen glass or damage to driving circuit. Therefore it must be packed in a strong
case before the transportation or handling.
2.12 For the storage make sure to put it in a place where the environment can be controlled so as
to prevent the temperature and humidity from exceeding the limits as specified in the manual. For
prolonged storage, it is necessary to house it in an anti-moisture bag and put them altogether in
one place. The ambient conditions are tabulated as follows:
Temperature Operation range 5 ~ +35 oC
Storage range -20 ~ +60 oC
Humidity Operation range 20% ~ 85%
Storage range 10% ~ 90%
2.13 Display of a fixed picture for a long time may cause a permanent after-image on the screen,
as commonly called “ghost shadow”. The degree of the after-image varies with the maker of LCD
screen. This phenomenon doesn’t represent failure. This “ghost shadow” may remain in the
picture for a period of time (several minutes). But when operating it please avoid displaying still
picture in high brightness for a long time.

3. Installation precautions
3.1 The front panel of LCD screen is made of glass. When installing it please make sure to put it in
place.
3.2 For service or installation it’s necessary to use specified screw lest it should damage the
screen.
3.3 Be sure to take anti dust measures. Any foreign substance that happens to fall down between
the screen and the glass will affect the receiving and viewing effect
3.4 When dismantling or mounting the protective partition plate that is used for anti vibration and
insulation please take care to keep it in intactness so as to avoid hidden trouble.
3.5 Be sure to protect the cabinet from damage or scratch during service, dismantling or
mounting.
Adjustment Instruction

1 Safety Instructions

1.1 Power supply must be cut off when replacing or welding any component or inserting / pulling out
connective lines;
1.2 Anti-electrostatic measures must be carried out during the whole producing processes!
a) Do not touch IC by hands at will;
b) Use anti-electrostatic iron;
c) Welder must wear anti-electrostatic glove;
1.3 Replacing any component with special safety requirement must refer to component list without
changing its specification and model at will.

2 Adjustment Equipments

Multimeter or oscilloscope
VG-849
CA-210
USB
DVD (support HDMI 1.4 ) or equipments with the same functions

3 Adjustment Processes

3.1 Power voltage checking


According to the wiring diagram specified by “Product Specification”, connect power board
assembly, data processing assembly, IR/Key board assembly, backlight board assembly correctly,
supply with power, press button to power on the TV set.
Make sure the voltages of socket X101 each pin on the main board are correct.. Voltage value
and range are listed as Table 1:
Table 1 Voltage of X101 each pin
X101 Pin1 2 3 4 5 6,7 9 10,11 12,13

5 5 12
Voltage ≤5.2 V ≤5.2 V ≤5.2V 0 0 12V±5%
V±5% V±5% V±5%
+5V Main MAIN
Function BL_ON BL_PWM PWR_SW GND GND AMP_PWR
STB 5V 12V
3.2 Adjustment flow as Fig. 1:

Check if EDID、HDCP KEY、FLASH has been written?

General assembly and combined adjustment

White balance adjustment

Input central signal, check TV function (omitted


channel, analog parameters control, etc. ), check
earphone, speakers output.
Check accessory and packing

Check AV input, output and relevant functions.

Default settings before ex-factory


Input Component signal, check YPbPr functions.

Input D-SUB signal, check display and all functions Check other functions (Radio、
(such as analog parameter), H/V center, etc.. LCN、HDMI ARC/CEC、OAD, etc.)

Input HDMI signal, check display and all functions


Check USB multimedia port and
(such as analog parameter), H/V center, etc..

Fig. 1 Adjustment flow chart


4 Adjustment Instruction

4.1 The unit adjustment


4.1.1 According to the wiring diagram specified by “Product Specification”, connect
power/backlight board assembly, data processing assembly, IR/Key board assembly correctly, supply
with power, turn on the TV set. Check display.
4.1.2 Factory menu instruction
a) Press key “INPUT”, then press digital keys “2、5、8、0” in turn to enter into primary factory
menu;
b) Press keys “▲” and “▼” to move cursor to each page of primary factory menu, then press
key “OK” to enter into submenu page;
c) Press keys “▲” and “▼” to move cursor upward or downward within any one page;
d) Press keys “◄” and “►” to do adjustment when move cursor to one item;
e) Press key “MENU” to exit submenu page to the superior factory menu;
f) Press key “EXIT” to exit factory menu in any case;
g) Press key “OK” to enter the inferior factory submenu;
h) Factory menu item: Aging Mode to be used for aging the TV set; red, green blue and
white full screen picture displays in turn; default setting is OFF;
i) Factory menu item: ADC ADJUST to be used for ADC calibration for VGA and
Component;
j) Factory menu item: Fac. Channel Preset to be used for factory channel presetting; central
signal digital frequency value for Australia program is set as CH28(529.5 MHz) and
CH33(564.5 MHz); original digital program presetting could not change if central signal
setting has any modification, so please search for digital program manually by perform item
DTV of menu Channel;
k) Factory menu item: Color Temp. to be used for white balance adjustment;
l) Factory menu item: Store Setting Init.
m) Factory menu item: USB SW Update to be used for software updating from USB port;
when U disk containing updating software is inserted into USB port, choose the item to
perform updating process;
n) Factory menu item: Other Settings include settings of EEPROM Init, MEMC Update,
Power mode, MST DEBUG, ISP MODE, Backlight, SSC, NONLINEAR, Video Quality, Audio
Quality, Light Sensor, Overscan, etc.; no need any adjustment normally.
o) Factory menu item: Shipment to be used for initializing user data; Success flag will display
after initialization, then press KEY POWER only to power off the TV set.
p) Please perform EEPROM Init before adjustment for the first time if software has been
upgraded or data have been kept in EEPROM.
4.1.3 ADC calibration for D-SUB channel
a) Switch to D-SUB channel;
b) Press key “INPUT”, then press digital keys “2、5、8、0” in turn to enter into primary factory
menu;
c) Move cursor to item “ADC ADJUST” and press key “OK” to enter into the inferior submenu;
d) Input D-SUB signal (VG-849 Timing:856 (1024×768/60 Hz), Pattern:914 Chess Pattern);
move cursor to item “MODE”, press keys “▲” and “▼” to choose item “RGB”, then move
cursor to item “AUTO ADC” and press key “OK” to perform auto adjustment until prompt
“success” displays;
4.1.4 ADC calibration for Component channel
a) Switch to Component channel;
b) Press key “INPUT”, then press digital keys “2、5、8、0” in turn to enter into primary factory
menu;
c) Move cursor to item “ADC ADJUST” and press key “OK” to enter into the inferior submenu;
d) Input Component signal (VG-849 Timing:972(1080i), Pattern:918 100% color bar); move
cursor to item “MODE”, press keys “▲” and “▼” to choose item “YPbPr”, then move cursor to
item “AUTO ADC” and press key “OK” to perform auto adjustment until prompt “success”
displays;
4.2 White balance adjustment
Unless specified by customer, default settings of COOL color temperature is 12000K and
chromatic coordinates is (280、290); referenced settings of Normal color temperature is 9300K and
chromatic coordinates is (295、305); referenced settings of Warm color temperature is 6500K and
chromatic coordinates is (313、329);
Default setting is Normal.
4.3 Adjustment procedures
The TV set should be working above 30 minutes to be in a stabler state before adjustment. Use
CA-210 BBY channel to adjust white balance;
a) Switch to HDMI channel;
b) Press key “INPUT”, then press digital keys “2、5、8、0” in turn to enter into primary factory
menu;
c) Move cursor to item “W/B ADJUST” and press key “OK” to enter into the inferior submenu;
d) Input HDMI signal (VG-849 Timing:856(1024×768/60 Hz),Pattern:914 Chess Pattern);
move cursor to item “MODE”, press keys “▲” and “▼” to choose item “HDMI”, then move
cursor to item “TEMPERTURE” and press keys “▲” and “▼” to choose “COOL”;
e) Fix “G GAIN”, adjust “R GAIN, B GAIN” to set 14th chromatic coordinates as (272、278);
f) Fix “G OFFSET”, adjust “R OFFSET、B OFFSET” to set 4th chromatic coordinates as
(272、278);
g) To make sure chromatic coordinates of bright scale are (X=280±10,Y=290±10) and
chromatic coordinates of dark scale are (X=280±10,Y=290±10) during adjusting;
h) Move cursor to item “COPY ALL” to copy white balance data to other channels except DTV
channel;
i) Check if chromatic coordinates of NORMAL and WARM meet the requirements (permitted
error of NORMAL bright scale: x±10,y±10, permitted error of NORMAL dark scale: x±10,
y±10; permitted error of WARM bright scale and dark scale: x±10,y±10); if not, adjust
“R_GAIN /B_GAIN/R_OFF/B_OFF” to be up to the requirements and then save the data;
j) Perform “Copy All” for Normal/Warm adjustments except DTV channel;
k) Check if chromatic coordinates of other channels meet the requirements, if not, do
adjustment for nonstandard channel alone with the same procedures from b) to j) as HDMI
channel’s and then save the data;
l) Switch to HDMI channel, change to 16-grey-scale program from central signal source,
adjust white balance with the same procedures from e) to g) as HDMI channel’s; but pay
attention not to perform “COPY ALL”!
m) Inspect all channels after completing adjustment to check if display is normal;
n) Refer to the following rule for adjustment:
B Gain/Offset: adjust B Gain/Offset downward, coordinates of X and Y will increase, adjust B
Gain/Offset upward, coordinates of X and Y will decrease;
R Gain/Offset: adjust R Gain/Offset will affect X value, but affect Lv value slightly, adjust R
Gain/Offset upward, coordinates of X will increase, adjust R Gain/Offset
downward, coordinates of X will decrease;
G Gain/Offset: adjust G Gain/Offset will affect Y value, and affect Lv value greatly, adjust G
Gain/Offset upward, coordinates of Y will increase, adjust G Gain/Offset
downward, coordinates of Y will decrease;
Note: Sanyo customer requires that default color temperature is Normal, adjust white
balance of color temperature Normal and Cool in Dynamic picture mode; for other
customers, please adjust white balance of color temperature Cool in Dynamic picture mode.
5 Function check
5.1 TV functions
Input central signal to RF port, enter into menu Channel first, then search for programs
automatically and check if there is any omitted program; check the speakers output and the picture
display;
5.2 AV port
Input AV signal with formats listed as Table 1 separately, check picture, sound and other
functions;
Table 1 AV video signal formats
Lines per
No. H.- Freq.(kHz) V.- Freq.(Hz) Note
frame
1 525 15.734/15.75 59.94/60 NTSC, NTSC4.43,PAL60,PAL-M
2 625 15.625 50 PAL, PAL-N, SECAM
5.3 Component port
Input Component signal from VG-849 with formats listed as Table 2 separately, check picture and
sound in the case of power-on, switching channel, changing mode, etc.;
Table 2 Component signal formats
H.- Freq. V.- Freq. Dot pulse Freq.
No. Definition Note
(kHz) (Hz) (MHz)
1 720×480 15.734/15.75 59.94/60 13.5/13.514 480i (NTSC)
2 720×576 15.625 50 13.5 576i (PAL)
3 720×480 31.469/31.5 59.94/60 27/27.027 480p (NTSC PROG)
4 720×576 31.25 50 27 576p (PAL PROG)
5 1280×720 37.5 50 74.25 720p (50p)
6 1280×720 44.955/45 59.94/60 74.176/74.25 720p (59.94p/60p)
7 1920×1080 28.125 50 74.25 1080i (50i)
8 1920×1080 33.75 59.94/60 74.176/74.25 1080i (59.94p/60p)
9 1920×1080 26.973 23.976 74.176 1080p (23.97p)
10 1920×1080 27 24 74.25 1080p (24p)
11 1920×1080 28.125 25 74.25 1080p (25p)
12 1920×1080 33.716 29.97 74.176 1080p (29.97p)
13 1920×1080 33.75 30 74.25 1080p (30p)
14 1920×1080 56.25 50 148.5 1080p (50p)
15 1920×1080 67.432/67.5 59.94/60 148.35/148.5 1080p (59.94p/60p)
5.4 D-SUB port
Input D-SUB signal from VG-849 with formats listed as Table 3 separately, check picture and
sound; if H./V. of picture displays abnormally, enter into main menu Picture->Screen->Auto Adjust to
perform auto calibration.
Table 3 D-SUB signal formats
H.- Freq. V.- Freq. Dot pulse Freq.
No. Definition Note
(kHz) (Hz) (MHz)
1 640×480 31.469 59.94 25.175 IBM
2 720×400 31.469 70.086 28.322 IBM
3 640×480 37.861 72.809 31.5 VESA
4 640×480 37.5 75 31.5 VESA
5 800×600 35.156 56.25 36 VESA
6 800×600 37.879 60.317 40 VESA
7 800×600 48.077 72.188 50 VESA
8 800×600 46.875 75 49.5 VESA
9 1024×768 48.363 60.004 65 VESA
10 1024×768 56.476 70.069 75 VESA
11 1024×768 60.023 75.029 78.75 VESA
12 1152×864 67.5 75 108 VESA
13 1280×960 60 60 108 VESA
14 1280×1024 63.98 60.02 108 VESA
15 1280×1024 80 75 135 SXGA
16 1360×768 47.7 60 85.5 WXGA
WXGA+ ( Panel
17 1440×900 55.9 60 106.5
National only)
WSXGA+ ( Panel
18 1680×1050 65.3 60 146.25
National only)
19 1920×1080 67.5 60 148.5
5.5 HDMI port
HDMI port supports all signal formats supported by Component port (Table 2) and D-SUB port
(Table 3), furthermore, it can also support signal with formats listed as Table 4 and Table 5 (video and
audio combination). Check picture and sound in the case of power-on, switching channel, changing
mode, etc.;
Table 4 Digital HDMI signal formats
Dot pulse
No H.- Freq. V.- Freq.
Definition Freq. Note
. (kHz) (Hz)
(MHz)
720(1440)×480i@59.94/60 Hz,
1 720(1440)×480 15.734/15.75 59.94/60 27/27.027
4:3/16:9
2 720(1440)×576 15.625 50 27 720(1440)×576i@50 Hz,4:3/16:9
Table 5 Video & audio signal formats of digital HDMI
No. Item Unit Parameter Note
Deep color:RGB 4:4:4(24 bit/pixel,30 bit/pixel,36 bit/pixel)、
YUV 4:4:4 (24 bit/pixel,30 bit/pixel,36 bit/pixel)、
1 Video
对于1080p,deep color只支持到30 bit/pixel。
YUV 4:2:2(16 bit)、YUV 4:2:2(20 bit)、YUV 4:2:2(24 bit)
Audio sample
2 kHz 32、44.1、48
freqence
Audio data
3 Bit 16、20、24
width
5.6 USB port
5.6.1 PVR function
Insert a formatted U disk in which recorded programs have been saved; press key “Record
List” to choose and play one program, check picture, sound and other functions;
5.6.2 Media playing function
Insert a U disk kept files of picture, sound and video, check picture, sound and other
functions;
Supported media formats as below:
Photo:JPEG,BMP,PNG
Video:H.264 ,MPEG-1,MPEG-2,VC-1,FLV
Audio:WMA,MP3,M4A (AAC)
5.7 Music port (depending on different models whether contain the port or not)
Input audio signal to side music port (analog audio input) from audio output equipment, check
audio output.
5.8 Other functions check
a) Check timing on/off, sleeping time off, picture/sound mode, OSD, stereo, digital audio port,
etc,;
b) Check pure digital audio programs (RADIO) ;
c) Check logical channel number (LCN);
d) Check HDMI ARC;
e) Check HDMI CEC;
f) Check OAD for special customer;

6 User Menu Setting before Ex-factory

Enter into Factory Menu and choose “Shipment” to perform presetting before ex-factory;
Main procedures are described as follow:
a) Clear out all programs;
b) Clear out information of VCHIP,parent control, etc.;
c) Default user analog parameter setting;
d) Recover default password;
e) Set Menu Language as English;
f) Set Power mode as Off。
Software Upgrading Instruction

Software Upgrading Instruction as Table 6

Table 6 Software Upgrading Instruction


Software SMT before
Location Part No. Part model Upgrading method
function upgrading

Upgrade with ALL100, etc.,


N104 5272532006 EN25Q32A-100HIP FLASH Yes need write protection, refer to
Note1;
N109 5272404005 CAT24C04WI-GT3 HDCP KEY Yes
Upgrade with ALL100, etc.
NB07 5272402003 CAT24C02WI VGA EDID Yes
Note 1 Write protection setting method: enter into ALL-100 upgrading interface “AUTO”, tick off
“Config”, press “config Setting”, set option “Protect” as “All Protect” and “SRWD” as “Enable”,
then press “OK” to complete write protection setting;
Please make sure option “Config” is ticked off during software upgrading and reset write
protection after ALL-100 upgrading software is opened each time;
Note 2 Upgrading method with ISP upgrading instrument:
1) Main board upgrading: connect 4-core line of ISP to Debug port (X103) on main board;
The Unit upgrading: connect both VGA ports of ISP and main board, enter into factory menu and
set “ISP Mode” as “ON”;

2) Use Mstar upgrading instrument (V4.4.2.0 or higher version), enter into menu “Device”, tick off
“WP Pin pull to high during ISP” to make sure Flash hardware write protection is removed and
erasing process is normal; please refer to Fig.2;

Fig. 2 Write protection setting

3) Press menu “Connect”, dialog box “Device Type is MX25L64” (device type depending on parts
used on board actually) will display to show successful connection; please refer to Fig. 3;
Fig. 3 Device MX25L64 successful connection
If connection is failed, press the first menu “Device” and choose “MX25L64” manually, then press
“Connect”;

4) Press “Read”, choose upgrading file, such as “MERGE.bin”; please refer to Fig. 4;

Fig. 4 Choosing upgrading file

5) Press “Auto”, tick off “All chip”, “program” and other necessary options; please refer to Fig. 5;

Fig. 5 Options
6) Press “Run” shown as Fig. 4 to perform upgrading in two steps, “Erase” and “Program”;

Normal upgrading process:

The first step “Erasing…, Flash Status: 03” will last for some time, or erasing is failed if the step

passes over immediately; please confirm procedure 2) to perform upgrading again;

The second step is “Programming…,Flash Status:00”;

Then prompt “Pass” displays;

7) Prompt “Pass” will display by button “Run” when upgrading succeeds; please refer to Fig. 6;

Fig. 6 Prompt “Pass” displayed by “Run” when upgrading succeeds

8) Need not exit ISP upgrading interface if there are other TV sets to be upgraded , only procedures
3) and 6) need repeat;

Note 3 Upgrading with USB:

1) Make sure the U disk is formatted as FAT32;

2) Copy software file named as “Merge. bin” to the U disk;

3) Turn on the TV set, then insert the U disk in USB port of the unit;
a) First press key “INPUT”, then press keys “2、5、8、0” in turn to enter into primary factory
menu;
b) Choose “USB SW Update” to begin upgrading;

4) Upgrading processes:

A、Read data from the U disk while data indicator light of the U disk is twinkling at the same time;

B、Upgrading flash, then the unit will be in “standby” mode;

5) Cut off the power supply and then restart the TV set, enter into factory menu to verify version and
time parameter, then perform “EEPROM Init” to complete the whole upgrading processes.

Note: The USB upgrading method can not be sure to be suitable for all kinds of U disk, so try another U
disk if necessary.
Working Principle of the Unit

1、 ATV PAL signal flow


Receive RF PAL analog signal and sent it to XC5200C (D/A silicon Tuner controlled by main chip
MSD309PX through I2C bus) to be demodulated, then differential IF signal is send out to main chip
MSD309PX analog demodulation to be demodulated to get analog CVBS video signal and SIF sound
signal.
CVBS video signal is processed by back-end video decoder, anti-interlacing part, video processor
and zoom controller, then LVDS signal is outputted to drive display panel.
SIF sound signal is processed by back-end demodulator to get analog sound signal, then processed
by pre-amplifier, acoustic effect processor and volume controller to get two parts of signals: the analog
part of signal is sent to earphone amplifier BH3547F to be amplified and then outputted to earphone jack;
the digital part of signal I2S is sent to digital audio power amplifier TAS5711 to be processed by D/A
converter and power amplifier, then outputted to drive speakers.

2、 DVB-T signal flow


Receive RF DVB-T digital signal and sent it to XC5200C (D/A silicon Tuner controlled by main chip
MSD309PX through I2C bus) to be processed by down-frequency-conversion, then differential IF signal is
send out to main chip MSD309PX digital demodulation to be demodulated, then standard parallel
transmission flow is outputted to back-end demultiplexer and decoder to be processed.
Video channel: demultiplexing digital video signal is processed by MSD309PX decoder and video
processor, then LVDS signal is outputted to drive display panel;
Audio channel: demultiplexing digital audio signal is processed by MSD309PX decoder and audio
processor, then double-sound-track analog audio signal (stereo) is outputted to MSD309PX to be
processed by preamplifier, acoustic effect processor and volume controller to get two parts of signals: the
analog part of signal is sent to earphone amplifier BH3547F to be amplified and then outputted to
earphone jack; the digital part of signal I2S is sent to digital audio power amplifier TAS5711 to be
processed by D/A converter and power amplifier, then outputted to drive speakers.

3、 AV input signal flow


AV video signal is inputted to main chip MSD309PX to be processed by video decoder,
anti-interlacing part, video processor and zoom controller, then LVDS signal is outputted to drive display
panel;
AV audio signal is processed by voltage divider, resistance matcher and AC coupler, then sent to
main chip MSD309PX to be processed by acoustic effect processor and volume controller to get two parts
of signals: the analog part of signal is sent to earphone power amplifier BH3547F to be amplified and
then outputted to earphone jack; the digital part of signal I2S is sent to digital audio power amplifier
TAS5711 to be processed by D/A converter and power amplifier, then outputted to drive speakers.

4、 D-SUB/YPbPr input signal flow


D-SUB、YPbPr video signal is inputted to main chip MSD309PX to be processed by A/D convertor,
video decoder, anti-interlacing part, video processor and zoom controller, then LVDS signal is outputted to
drive display panel;
D-SUB、YPbP audio signal is processed by voltage divider, resistance matcher and AC coupler, then
sent to main chip MSD309PX to be processed by acoustic effect processor and volume controller to get
two parts of signals: the analog part of signal is sent to earphone power amplifier BH3547F to be
amplified and then outputted to earphone jack; the digital part of signal I2S is sent to digital audio power
amplifier TAS5711 to be processed by D/A convertor and power amplifier, then outputted to drive
speakers.

5、 HDMI input signal flow


HDMI video signal is inputted to main chip MSD309PX to be processed by video decoder, video
processor and zoom controller, then LVDS signal is outputted to drive display panel;
HDMI audio signal is sent to main chip MSD309PX to be processed by audio decoder, pre-amplifier,
acoustic effect processor and volume controller to get two parts of signals: the analog part of signal is sent
to earphone power amplifier BH3547F to be amplified and then outputted to earphone jack; the digital
part of signal I2S is sent to digital audio power amplifier TAS5711 to be processed by D/A convertor and
power amplifier, then outputted to drive speakers.
Block Diagram

N204

NB08
BH3547F

Speakers

NV01

1
IC Block Diagram

1、 TUNER IC XC5200C
The Single-Chip Multi-Standard Tuner XC5200C supports all analog TV
formats transmitted worldwide in the 42-1000 MHz band on either cable or
terrestrial broadcast channels. It implements on-chip tuning, and channel
filtering without external (SAW) filters and has no manually tunable parts.
The broadband tuner converts the selected channel into an Intermediate
Frequency (IF), which is then sampled by an internal high-resolution
analog-to-digital converter (A/D) for further processing.
The IF signals are filtered using a standard-dependent high-rejection
channel filter and converted to a user programmable output frequency. At the
output of the D/A converter, the TV signal is low-pass filtered using a
high-performance smoothing filter and input to a variable gain amplifier. The IF
output amplifier gain can be controlled via an external analog signal on Vagc.
The XC5200C architecture is summarized in Figure 1. XC5200C Block
Diagram.
2、 AMP IC TAS5711
The TAS5711 is a 20-W, efficient, digital audio power amplifier for driving
stereo bridge-tied
speakers. One serial data input allows processing of up to two discrete audio
channels and seamless integration to most digital audio processors and MPEG
decoders. The device accepts a wide range of input data and data rates. A fully
programmable data path routes these channels to the internal speaker drivers.
The TAS5711 is an I2S slave-only device receiving all clocks from external
sources. The TAS5711
operates with a PWM carrier between 384-kHz switching rate and 352-KHz
switching rate depending on the input sample rate. Over sampling combined
with a fourth-order noise shaper provides a flat noise floor and excellent
dynamic range from 20 Hz to 20 kHz.
3、 Headphone Amplifier BH3547F

●Description
BH3547F is one headphone amplifier suitable for portable products.
BH3547F has a fixed gain of 6 dB.
External resistors for gain setting are not needed. Package of BH3541F, BH3544F, BH3547F, BH3548F is pin-to-pin
compatible (SOP8), enable to replace each other easily.
BH3547F also has mute functions that make it easy to prevent pop noise when power supply turns on/off. Moreover,
thermal shutdown function is built-in.
BH3547F can drive 16/32Ω load.
receiver.

●Features
1) Built-in mute function for preventing pop noise when power supply turns on/off
2) Built-in thermal shutdown function
3) BH3541F, BH3544F, BH3547F, BH3548F are pin-to-pin compatible
4) SOP8 small package

●Applications
TV, Desktop PC, Notebook PC, Camcorder and other equipment having headphone output

●Block diagra
m
V CC O UT2 BIA S IN2
8 7 6 5

B IAS
180 k
0d B (90 k)
(6d B)

TS D 180 k
(9 0k)

0 dB
(6d B)
MUTE

1 2 3 4

OU T1 MUTE I N1 G ND
A B C D E F G H

1
Wiring Diagram
LVDS

PANEL
2

X401

X101
3

POWER BOARD

X504
INVERTER
4
MAIN BOARD
X703

X501 X104 X102


5 XV01

TITLE: DWG NO.

9222KI5101JL
X1 X903 LE-22KI51 H
6 KEY BOARD IR BOARD DRAWN BY
REV. V1.0
Sheet1 to 1
POWER SWITCH XOCECO
APPROVED BY
XIAMEN OVERSEAS CHINESE
ELECTRONIC CO., LTD.
Troubleshooting Block Diagram

1.Panel doesn’t light up.

Supply with power,


check if red indicator Yes
lights up in STANDBY
state?
Press key POWER Red
No on remote control or
the unit, check
indicator.
Check if 5V is supplied
to X101-PIN3 ? Blue

No Check if level of
X101-PIN1 on main
Check STANDBY
board is high?
circuits on power
board. Yes
Check backlight
No board.

Check power Check if level of


control circuits on No X101-PIN5 on main
main board. board is high?

Yes

Check power Check power


control circuits on board.
main board.
2.No picture, but backlight is normal:

Can control the TV set Yes Press key MENU, Yes


by keys on remote can OSD display
control or the unit? normally?
No
No
Yes Do noTVchannel
have picture at
all?
Enter into factory menu to initialize No
EEPROM, then cut off main power
No and then turn on the TV set again,
check if there is picture?
Yes

Readjust the
main board.

Replace the main


board
3.No sound, but picture is normal:

No sound

Check if level of Yes Check if there is No Check IIS


NV01-PIN19&25 signal inputted to (signal input
are all high? NV01-PIN15&20&21 circuits) on main
No &22 ? board.
Yes

Check if level of Check power voltage No Check +24V on


VV02-b is low? of NV01. power board.

Yes No Yes

Replace Check IIC signal of


VV02 NV01- PIN23&24.

Check Reset &


Mute circuits of
power amplifier.
A B C D E F G H
N101 -A MSD309PX-LF-V1
N103 N102
K4T51163QG-HCF7 K4T51163QG-HCF7
Close to 309
MIUA MIUB Close to 309
MA_BA0 L2 B9 MA_DQ15 MIUA_ODT R123 75 MA_ODT MIUA_A0 C10 E23 MIUB_A0 MIUB_ODT R146 75 MB_ODT MB_BA0 L2 B9
BA0 DQ15 PAD_IO[8](A_A0) PAD_IO[55](B_A0) MB_DQ15
MA_BA1 L3 B1 MA_DQ14 MIUA_WEZ MA_WEZ MIUA_A1 A22 U24 MIUB_A1 MIUB_WEZ MB_WEZ MB_BA1 L3 BA0 DQ15
B1
BA1 DQ14 PAD_IO[41](A_A1) PAD_IO[88](B_A1) MB_DQ14
D9 MA_DQ13 MIUA_MCKE MA_CKE A9 D24 MIUB_A2 MIUB_MCKE MB_CKE BA1 DQ14
MIUA_A2 D9
1 MA_A12
MA_A11
MA_A10
R2
P7
M2
A12
A11
DQ13
DQ12
DQ11
D1
D3
D7
MA_DQ12
MA_DQ11
MIUA_BA1
MIUA_BA0
R124 75 MA_BA1
MA_BA0
MIUA_A3
MIUA_A4
B23
B9
A23
PAD_IO[5](A_A2)
PAD_IO[44](A_A3)
PAD_IO[3](A_A4)
PAD_IO[52](B_A2)
PAD_IO[91](B_A3)
PAD_IO[50](B_A4)
V25
D25
V24
MIUB_A3
MIUB_A4
MIUB_A5
MIUB_BA1
MIUB_BA0
R147 75 MB_BA1
MB_BA0
MB_A12
MB_A11
R2
P7 A12
A11
DQ13
DQ12
DQ11
D1
D3
MB_DQ13
MB_DQ12
MB_DQ11
MA_DQ10 MIUA_A4 MA_A4 MIUA_A5 MIUB_A4 MB_A4 MB_A10 M2 D7 MB_DQ10
P3 A10 DQ10 C9 PAD_IO[43](A_A5) PAD_IO[90](B_A5) D23 A10 DQ10
MA_A9 C2 MA_DQ9 MIUA_A6 MA_A6 MIUA_A6 MIUB_A6 MIUB_A6 MB_A6 MB_A9 P3 C2 MB_DQ9
MA_A8 P8 A9 DQ9 C8 C23 PAD_IO[6](A_A6) PAD_IO[53](B_A6) W25 A9 DQ9
MA_DQ8 MIUA_A8 MA_A8 MIUA_A7 MIUB_A7 MIUB_A8 MB_A8 MB_A8 P8 C8 MB_DQ8
A8 DQ8 R125 75 PAD_IO[45](A_A7) PAD_IO[92](B_A7) R148 75 A8 DQ8
MA_A7 P2 F9 MA_DQ7 MIUA_A11 MA_A11 MIUA_A8 B8 C25 MIUB_A8 MIUB_A11 MB_A11 MB_A7 P2 F9 MB_DQ7
A7 DQ7 MA_MCLK PAD_IO[4](A_A8) PAD_IO[51](B_A8) A7 DQ7 MB_MCLK
MA_A6 N7 F1 MA_DQ6 MA_MCLKZ MIUA_A9 A24 W24 MIUB_A9 MB_A6 N7 F1 MB_DQ6
A6 DQ6 MIUA_A5 MA_A5 PAD_IO[46](A_A9) PAD_IO[93](B_A9) MIUB_A5 MB_A5 MB_MCLKZ
MA_A5 N3 H9 MA_DQ5 MIUA_A10 B22 V23 MIUB_A10 MB_A5 N3 A6 DQ6 H9
A5 DQ5 MIUA_A10 MA_A10 PAD_IO[42](A_A10) PAD_IO[89](B_A10) MIUB_A10 MB_A10 MB_DQ5
MA_A4 N8 H1 MA_DQ4 MIUA_A11 C8 C24 MIUB_A11 MB_A4 N8 A5 DQ5 H1
A4 DQ4 R116 R117 MIUA_A1 MA_A1 PAD_IO[2](A_A11) PAD_IO[49](B_A11) MIUB_A1 MB_A1 MB_DQ4 R166 R167
MA_A3 N2 H3 MA_DQ3 100 R126 75 MIUA_A12 B24 W23 MIUB_A12 R149 75 A4 DQ4
100 MIUB_BA2 MB_BA2 MB_A3 N2 H3 MB_DQ3 100 100
M7 A3 DQ3 MIUA_BA2 MA_BA2 B7 PAD_IO[35](A_A12) PAD_IO[82](B_A12) B25 A3 DQ3
MA_A2 H7 MA_DQ2 MIUA_A13 MIUB_A13 MB_A2 M7 H7 MB_DQ2
MA_A1 M3 A2 DQ2 G2 MIUA_A12 MA_A12 PAD_IO[0](A_A13) PAD_IO[47](B_A13) MIUB_A12 MB_A12 A2 DQ2
MA_DQ1

C110
MB_A1 M3 G2 MB_DQ1

47n
M8 A1 DQ1 MIUA_A7 MA_A7 C13 H23 MIUB_A7 MB_A7 A1 DQ1 C115
MA_A0 G8 MA_DQ0 MIUA_DQ0 MIUB_DQ0 MB_A0 M8 G8 MB_DQ0 47n
A0 DQ0 MIUA_A9 MA_A9 MIUA_DQ1 A19 PAD_IO[14](A_DQ0) PAD_IO[61](B_DQ0) P24 MIUB_A9 MB_A9 A0 DQ0
R127 75 MIUB_DQ1 R150 75
A9 +1.8V-DDR2 MIUA_A3 MA_A3 MIUA_DQ2 A12 PAD_IO[32(A_DQ1) PAD_IO[79](B_DQ1) G24 MIUB_DQ2 MIUB_A3 MB_A3
A9 +1.8V-DDR2
MA_MCLKZ K8 VDDQ1 C1 MIUA_DQ3 B19 PAD_IO[15](A_DQ2) PAD_IO[62](B_DQ2) R23 MIUB_A2 VDDQ1
MIUA_A2 MA_A2 MIUB_DQ3 MB_A2 MB_MCLKZ K8 C1
MA_MCLK J8 CK VDDQ2 C3 Close to DDR MIUA_DQ4 C20 PAD_IO[33](A_DQ3) PAD_IO[80](B_DQ3) R24 MIUB_A0 CK VDDQ2
MIUA_A0 MA_A0 MIUB_DQ4 MB_A0 MB_MCLK J8 C3 Close to DDR
CK VDDQ3 C7 R128 75 B12 PAD_IO[34](A_DQ4) PAD_IO[81](B_DQ4) G25 MIUB_CASZ R151 75 MB_CASZ CK VDDQ3
MIUA_CASZ MA_CASZ MIUA_DQ5 MIUB_DQ5 C7
K2 VDDQ4 C9 MIUA_DQ6 C19 PAD_IO[13](A_DQ5) PAD_IO[60](B_DQ5) P23 MIUB_RASZ MB_RASZ VDDQ4
MA_CKE MIUA_RASZ MA_RASZ MIUB_DQ6 MB_CKE K2 C9
CKE VDDQ5 E9 MIUA_DQ7 A13 PAD_IO[31](A_DQ6) PAD_IO[78](B_DQ6) H24 CKE VDDQ5
MIUA_A13 R129 75 MA_A13 MIUB_DQ7 MIUB_A13 R152 75 MB_A13 E9
VDDQ6 G1 MIUA_DQ8 B14 PAD_IO[17](A_DQ7) PAD_IO[64](B_DQ7) J25 VDDQ6
MIUB_DQ8 G1
L8 VDDQ7 G3 MIUA_DQ9 C18 PAD_IO[18](A_DQ8) PAD_IO[65](B_DQ8) N23 VDDQ7
MIUA_MCLK MA_MCLK MIUB_DQ9 MIUB_MCLK MB_MCLK L8 G3
CS VDDQ8 G7 C14 PAD_IO[29](A_DQ9) PAD_IO[76](B_DQ9) J24 CS VDDQ8
MIUA_MCLKZ R130 22 MA_MCLKZ MIUA_DQ10 MIUB_DQ10 MIUB_MCLKZ R153 22 MB_MCLKZ G7 +1.8V-DDR2
MA_WEZ K3 VDDQ9 G9 A18 PAD_IO[19](A_DQ10) PAD_IO[66](B_DQ10) N24 VDDQ9
MIUA_DQ11 MIUB_DQ11 MB_WEZ K3 G9
WE VDDQ10 B18 PAD_IO[30](A_DQ11) PAD_IO[77](B_DQ11) N25 WE VDDQ10
MIUA_DQ12 MIUB_DQ12
2 MA_RASZ K7
RAS VDD1
A1
MIUA_DQM1 MA_DQM1
MIUA_DQ13 B13
B17
PAD_IO[28](A_DQ12)
PAD_IO[16](A_DQ13)
PAD_IO[75](B_DQ12)
PAD_IO[63](B_DQ13)
J23
M25
MIUB_DQ13 MIUB_DQM1 MB_DQM1 MB_RASZ K7
RAS VDD1
A1

100n

100n

100n

100n

100n

100n

100n

100n
C117

C119

C121

C123

C125

C127

C129

C132
E1 MIUA_DQ14 MIUB_DQ14 E1
MA_CASZ VDD2 MIUA_DQM0 R131 22 MA_DQM0 PAD_IO[27](A_DQ14) PAD_IO[74](B_DQ14) MIUB_DQM0 R154 22 MB_DQM0 VDD2
L7 J9 MIUA_DQ15 C15 K23 MIUB_DQ15 MB_CASZ L7 J9
CAS VDD3 M9 PAD_IO[20](A_DQ15) PAD_IO[67](B_DQ15) CAS VDD3
VDD4 M9
MA_DQM0 F3 R1 MIUA_DQS0 A16 L24 MIUB_DQS0 MB_DQM0 VDD4
LDM VDD5 MB_DQS0 F3 R1
MA_DQM1 B3 MIUA_DQS0 MA_DQS0 MIUA_DQSB0 C16 PAD_IO[23](A_DQS0) PAD_IO[70](B_DQS0) L23 MIUB_DQS0 MB_DQM1 LDM VDD5
MIUB_DQSB0 B3
UDM J1 MIUA_DQSB0 R132 22 MA_DQSB0 A15 PAD_IO[24](A_DQS0B) PAD_IO[71](B_DQS0B) K24 MIUB_DQSB0 R155 22 MB_DQSB0 UDM +1.8V-DDR2
MIUA_DQS1 MIUB_DQS1 J1
MA_ODT K9 VDDL J7 B15 PAD_IO[21](A_DQS1) PAD_IO[68](B_DQS1) K25 MB_ODT VDDL
MIUA_DQSB1 MIUB_DQSB1 K9 J7
ODT VSSDL PAD_IO[22](A_DQS1B) PAD_IO[69](B_DQS1B) ODT VSSDL
MIUA_DQS1 MA_DQS1 MIUA_DQM0 B16 M23 MIUB_DQM0 MIUB_DQS1 MB_DQS1

100n

100n

100n

100n

100n

100n

100n

100n

100n
C116

C118

C120

C122

C124

C126

C128

C130

C131
MA_DQS0 F7 A7 MIUA_DQM1 C17 PAD_IO[26](A_DQM0) PAD_IO[73](B_DQM0) M24 MIUB_DQSB1 R156 MB_DQS0
LDQS VSSQ1
MIUA_DQSB1 R133 22 MA_DQSB1 PAD_IO[25](A_DQM1) PAD_IO[72](B_DQM1)
MIUB_DQM1 22 MB_DQSB1 F7 A7
MA_DQSB0 E8 B2 MB_DQSB0 LDQS VSSQ1
LDQS VSSQ2 E8 B2
B8 MIUA_MCLK C12 G23 MIUB_MCLK MIUB_DQ11 MB_DQ11 LDQS VSSQ2 B8
VSSQ3 MIUA_DQ11 MA_DQ11 PAD_IO[12](A_MCLK) PAD_IO[59](B_MCLK)
D2 MIUA_MCLKZ B11 F25 MIUB_MCLKZ MIUB_DQ12 VSSQ3
VSSQ4 MIUA_DQ12 MA_DQ12 PAD_IO[10](A_MCLKZ) PAD_IO[57](B_MCLKZ) MB_DQ12 D2
MA_DQS1 B7 D8 MIUA_MCKE C21 T23 MIUB_MCKE MB_DQS1 VSSQ4
MIUA_DQ9 R134 22 MA_DQ9 MIUB_DQ9 R157 22 MB_DQ9 B7 D8
MA_DQSB1 A8 UDQS VSSQ5 E7 PAD_IO[37](A_CKE) PAD_IO[84](B_CKE) MB_DQSB1 UDQS VSSQ5
MIUA_DQ14 MA_DQ14 MIUB_DQ14 MB_DQ14 A8 E7
UDQS VSSQ6 F2 B20 R25 UDQS VSSQ6
MIUA_WEZ MIUB_WEZ F2
A_MVERF VSSQ7 MIUA_DQ6 MA_DQ6 PAD_IO[36](A_WEZ) PAD_IO[83](B_WEZ) MIUB_DQ6 MB_DQ6 B_MVERF
F8 MIUA_RASZ B10 F23 MIUB_RASZ VSSQ7 F8
VSSQ8 +1.8V-DDR2 MIUA_DQ1 MA_DQ1 PAD_IO[9](A_RASZ) PAD_IO[56](B_RASZ) MIUB_DQ1 MB_DQ1
J2 H2 MIUA_CASZ A10 E24 MIUB_CASZ J2 VSSQ8 H2 +1.8V-DDR2
VREF VSSQ9 MIUA_DQ3 R135 22 MA_DQ3 PAD_IO[7](A_CASZ) PAD_IO[54](B_CASZ) MIUB_DQ3 R158 22 MB_DQ3
H8 MIUA_BA0 A21 T24 MIUB_BA0 VREF VSSQ9 H8
VSSQ10 MIUA_DQ4 MA_DQ4 PAD_IO[39](A_BA0) PAD_IO[86](B_BA0) +1.8V-DDR2 MIUB_DQ4 MB_DQ4
A2 R114 MIUA_BA1 B21 T25 MIUB_BA1 A2 VSSQ10
NC#A2 PAD_IO[38](A_BA1) PAD_IO[85](B_BA1) R164
E2 A3 10K A_MVERF MIUA_DQ15 MA_DQ15 MIUA_BA2 C22 U23 MIUB_BA2 MIUB_DQ15 MB_DQ15 NC#A2 10K
NC#E2 VSS1 PAD_IO[40](A_BA2) PAD_IO[87](B_BA2) E2 A3 B_MVERF
MA_BA2 L1 E3 MIUA_DQ8 MA_DQ8 MIUA_ODT C11 F24 MIUB_ODT MIUB_DQ8 MB_DQ8 MB_BA2 NC#E2 VSS1
BA2 VSS2 PAD_IO[11](A_ODT) PAD_IO[58](B_ODT) R145 L1 E3
R3 J3 MIUA_DQ10 R136 22 MA_DQ10 MIUB_DQ10 R159 22 MB_DQ10 BA2 VSS2
NC#R3 VSS3 R115 C107 10K R3 J3
R7 N1 MIUA_DQ13 MA_DQ13 D22 MIUB_DQ13 MB_DQ13 NC#R3 VSS3 R165 C114
100n R7 N1
3 MA_A13 R8 NC#R7
NC#R8
VSS4
VSS5
P9
10K
MIUA_DQ7
MIUA_DQ0
MA_DQ7
MA_DQ0
MVREF
R144
10K
C111
100n
MIUB_DQ7
MIUB_DQ0
MIUB_DQ2
MB_DQ7
MB_DQ0
MB_A13 R8 NC#R7
NC#R8
VSS4
VSS5
P9
10K 100n

MIUA_DQ2 R137 22 MA_DQ2 R160 22 MB_DQ2


MIUA_DQ5 MA_DQ5 MIUB_DQ5 MB_DQ5
N105
MX25L12845EMI-10G Close to DDR
Close to DDR
1 16
NC/SIO3 SCLK
2 15
VCC SI/SIO0 N101 -D MSD309PX-LF-V1
3 14
NC_3 PO6
4 13 PWM Close to 309
N101 -C N101 -EMSD309PX-LF-V1
PO2 PO5 R119 10K AB25 AC24
MSD309PX-LF-V1
5 12 PAD_PWM0 PADA_OUTP_CH[6](PAD_R_ODD[7]) RXO0+ 004:B1
R120 10K AB24 AC25 R138 0
PO1 PO4 PAD_PWM1 PADA_OUTN_CH[6](PAD_R_ODD[6]) RXO0- 004:B1
E6 AD24
6 11 BL_PWM D6 PAD_PWM2 PADA_OUTP_CH[7](PAD_R_ODD[5]) AD25
RXO1+ 004:B1 HDMI AUDIO RGB CVBS
PO0 PO3 004:B2;005:B1 PAD_PWM3 PADA_OUTN_CH[7](PAD_R_ODD[4]) RXO1- 004:B1
AE24 G2 R4 M2 AC5 CVBS1_IN
7 10 PADA_OUTP_CH[8](PAD_R_ODD[3]) RXO2+ 004:B1 PAD_RX0N_A PAD_LINEIN_L0 VGA-LIN 003:G1 003:G3 VGA-R_IN- PADA_RIN0M PADA_CVBS0
AC23 R139 0 H3 R5 M3 W4 003:D3
CS GND PADA_OUTN_CH[8](PAD_R_ODD[2]) RXO2- 004:B1 PAD_RX0P_A PAD_LINEIN_R0 VGA-RIN 003:G1 003:G2 VGA-R_IN PADA_RIN0P PADA_CVBS1
8 9
SAR PADA_OUTP_CH[9](PAD_R_ODD[1])
AE23
RXOC+ 004:B2
H2
PAD_RX1N_A PAD_LINEIN_L1
T6
YPBPR-LIN 003:D2 003:G3 VGA-G_IN-
L2
PADA_GIN0M PADA_CVBS2
W5
SO/SIO1/PO7 J5 AD23 J3 U6 L3 AA5
005:E1 KEY PAD_SAR0 PADA_OUTN_CH[9](PAD_R_ODD[0]) RXOC- 004:B1 PAD_RX1P_A PAD_LINEIN_R1 YPBPR-RIN 003:D2 003:G2 VGA-G_IN PADA_GIN0P PADA_CVBS3
WP/SIO2 G4 AE22 J2 V6 K1 W2
PAD_SAR1 PADA_OUTP_CH[10](PAD_G_ODD[7]) RXO3+ 004:B2 PAD_RX2N_A PAD_LINEIN_L2 CVBS1-LIN 003:D4 003:G3 VGA-B_IN- PADA_BIN0M PADA_CVBS4
B4 AC22 R140 0 J1 U5 K3 W3
PAD_SAR2(POWER_DET) PADA_OUTN_CH[10](PAD_G_ODD[6]) RXO3- 004:B2 PAD_RX2P_A PAD_LINEIN_R2 CVBS1-RIN 003:D4 003:G2 VGA-B_IN PADA_BIN0P PADA_CVBS5
SPI-CK AA7 AC21 G3 AD6 K2

4 +3.3V-S
SPI-DI
SPI-CS-
PAD_SAR3 PADA_OUTP_CH[11](PAD_G_ODD[5])
PADA_OUTN_CH[11](PAD_G_ODD[4])
AD22
RXO4+
RXO4-
004:B2
004:B2
G1
M4
PAD_RXCN_A
PAD_RXCP_A
DDCDA_CK
PAD_LINEIN_L5
PAD_LINEIN_R5
AC6 003:G2
003:G2
003:G2
VGA-SOG_IN
VGA-HSYNC
VGA-VSYNC
N4
N5
PADA_SOGIN0
PAD_HSYNC0
PAD_VSYNC0
PADA_CVBS_OUT1
PADA_CVBS_OUT2
V3
AA4
CVBS_OUT
003:D4
SPI-DO
+3.3V-S
SPI PADA_OUTP_CH[12](PAD_G_ODD[3])
AC20
RXE0+ 004:B2
M5
DDCDA_DA PAD_LINEOUT_L0
V1
CVBS-LOUT 003:D6
N104 005:C1 LED C4 AD21 R141 0 K6 V2 R3 W1
EN25Q64-104HIP A4 PAD_GPIO_PM6(BOOT_FLASH_CS) PADA_OUTN_CH[12](PAD_G_ODD[2]) AE20 RXE0- 004:B2 PAD_HOTPLUGA PAD_LINEOUT_R0 AA6 CVBS-ROUT 003:D5 P2 PADA_RIN1M PADA_VCOM
R118 22 PAD_SPI_CZ(BACKUP_FLASH_CS) PADA_OUTP_CH[13](PAD_G_ODD[1]) C133 R168
A2 AD20 RXE1+ 004:B2 D2 PAD_LINEOUT_L3 Y5 P3 PADA_RIN1P
8 1
R111 47n 68
7
VCC CS
2 10K B3 PAD_SPI_CK PADA_OUTN_CH[13](PAD_G_ODD[0]) AE19 RXE1- 004:B2 E3 PAD_RX0N_B PAD_LINEOUT_R3 N2 PADA_GIN1M
NC/DQ3 DO/DQ1
A3 PAD_SPI_DI PADA_OUTP_CH[14](PAD_B_ODD[7]) AC19 RXE2+ 004:B2 E2 PAD_RX0P_B AD5 N3 PADA_GIN1P
R102 6 3 R142 0 HPAMP-LOUT
CLK WP/DQ2
PAD_SPI_DO PADA_OUTN_CH[14](PAD_B_ODD[6]) RXE2- 004:B2 PAD_RX1N_B PAD_EARPHONE_OUTL 003:F5 PADA_BIN1M
10K 5 4 B2 AC18 F3 AE5 M1
C101 DI/DQ0 VSS
PAD_GPIO_PM8(FLASH_WP) PADA_OUTP_CH[15](PAD_B_ODD[5]) RXEC+ 004:B2 PAD_RX1P_B PAD_EARPHONE_OUTR HPAMP-ROUT 003:F4 PADA_BIN1P
100n R112 AD19 F2 N1
C105 PADA_OUTN_CH[15](PAD_B_ODD[4]) AC17 RXEC- 004:B2 F1 PAD_RX2N_B W6 PADA_SOGIN1
100n 10K
PADA_OUTP_CH[16](PAD_B_ODD[3]) RXE3+ 004:B2 PAD_RX2P_B 2.2u PAD_HSYNC1
UART/I2CS PADA_OUTN_CH[16](PAD_B_ODD[2])
AD18
0 RXE3- 004:B2
D3
PAD_RXCN_B PAD_VRP
AB4
2.2u C113
Y6
PAD_VSYNC1
P6 AE17 R143 D1 AB5
003:A1;003:G1;005:D1 UART-RX DDCA_CK PADA_OUTP_CH[17](PAD_B_ODD[1]) RXE4+ 004:B2 PAD_RXCP_B PAD_VAG C112
N6 AD17 J6 AC3 U2
003:A1;003:G1;005:D1 UART-TX DDCA_DA PADA_OUTN_CH[17](PAD_B_ODD[0]) RXE4- 004:B2 DDCDB_CK AVSS_VRM_ADC_DAC 003:D2 YPBPR-PR_IN- PADA_RIN2M
L6 +3.3V U3
DDCDB_DA 003:D1 YPBPR-PR_IN PADA_RIN2P
J4 L101 T2
HOTPLUGB 003:D2 YPBPR-Y_IN- PADA_GIN2M
I2CM R171 R161 R170
BG1608B121
003:D1 YPBPR-Y_IN
T1
PADA_GIN2P
SCL
AA23
PAD_DDCR_CK
GPIO_TCON 003:A5 HDMI3-RX0-
AC8
PAD_RX0N_C I2S 10K 10K 10K 003:D2 YPBPR-PB_IN-
R1
PADA_BIN2M
AA24 AA10 AD9 A6 MCLK 005:E2 R2
SDA PAD_DDCR_DA PAD_TCON0 E2PWP- 001:A6 003:A5 HDMI3-RX0+ PAD_RX0P_C PAD_I2S_OUT_MCK 003:D1 YPBPR-PB_IN PADA_BIN2P
T5 AC9 B5 005:E3 T3
PAD_TCON1(SC1_RE1) 003:A5 HDMI3-RX1- PAD_RX1N_C PAD_I2S_OUT_SD SDIN 003:D1 YPBPR-SOG_IN PADA_SOGIN2
AB10 R232 AD10 B6 LRCLK V4
PAD_TCON2(FE_ANT5V_MONITOR) 0 003:A5 HDMI3-RX1+ PAD_RX1P_C PAD_I2S_OUT_WS 005:E3 PADA_HSYNC2
IR PAD_TCON3(TUNER_RESET)
AB7
003:A5 HDMI3-RX2-
AE10
PAD_RX2N_C PAD_I2S_OUT_BCK
C6 SCLK 005:E3
005:C2 IR G5 AA9 AC10
AVOUT_MUTE-

R163
PAD_IRIN PAD_TCON4 003:A5 HDMI3-RX2+ PAD_RX2P_C R162 R172

10K
V5 R233 AE8 C1
C108 PAD_TCON5(SC1_MUTE) AC11 0 003:A5 HDMI3-RXC- AD8 PAD_RXCN_C PAD_I2S_IN_BCK(USB0_OCD) H6 10K 10K
R122
5 +3.3V-S 30p

G101
1M
AD1
AE2
XTAL
PAD_XTAL_IN
PAD_TCON6(PCM_5V_CTL)
PAD_TCON7(SIDE_AV_DET)
AA8

R6
RST_DEMO
003:A5
003:A5
003:A6
HDMI3-RXC+
HDMI3-SCL
HDMI3-SDA
AE7
AD7
AC7
PAD_RXCP_C
DDCDC_CK
DDCDC_DA
PAD_I2S_IN_SD(USB0_CTL)
PAD_I2S_IN_WS
G6

24MHz PAD_XTAL_OUT PAD_TCON9(COMP_DET) SPDIF_CL 003:B6 HDMI3-HP HOTPLUGC


R113 PAD_TCON10(HP_DET)
Y8
HP-DCT- 003:H5
R169
100
SPDIF
C109 R121 Y9 K5 P5
Vcc 10K PAD_TCON11(HP_MUTE) HP-MUTE- 003:G4
003:A5;003:A2;003:A4 HDMI-CEC PAD_CEC PAD_SPDIF_OUT SPDIF
30p 0 RESET
E5
C104 RESET PAD_RESET T4 +3.3V-S
R235

100n
47K

C106 PAD_TCON15(SC1_DET)
GND 100n
USB
N106
APX810-29SAG-7
C2
PAD_DP_P0 GPIO
B1 A7
+3.3V PAD_DM_P0 PAD_GPIO0(NTP_MUTE) RESET_AMP 005:F4
003:G3 AD11 C7
USB-D+ PAD_DP_P1 PAD_GPIO1(AMP_RST) STB_AMP 005:E4
N110 003:G3 AE11 F4 BL_SW-
USB-D- PAD_DM_P1 PAD_GPIO2(INV_CTL) 005:B1
AT24LC32A/SN E4
R103 PAD_GPIO3(PANEL_CTL) PNPWR_SW 005:A5
1 8 10K C3
PAD_GPIO4(USB_CTL) USB_SW
2 A0 Vcc 7 R106 33 D4
E2PWP- 001:D5 LOGO_BL
3 A1 WP 6 R107 33 PAD_GPIO5(ERROR_OUT) F6
4 A2 SCL 5 R108 33 F11 PAD_GPIO12(AMD_SCL) F5
LVDS_I/O1 TITLE: DWG NO.
GND SDA E11 PAD_GND_EFUSE PAD_GPIO13(AMP_SDA) LVDS_I/O2
PAD_TESTPINPP
C102
100n 569KI0801A
GPIO_PM Core & Memory 9222KI5101DL
AB8
PAD_GPIO_PM0(5V_HDMI_3) H5
+3.3V +3.3V PAD_GPIO_PM1(5V_HDMI_1) ISP_EN 003:G1
C5

6 R101 1
N109
CAT24C04WI

8
R104
PAD_GPIO_PM4(POWER_ON_OFF)
PAD_GPIO_PM5(5V_HDMI_2)
PAD_GPIO_PM11(DSUB_DET)
K4
L5
M6 +3.3V-S
PWR_SW 005:B2
UART-RXSTB 003:A1
DRAWN BY
REV. A1.0
10K NC1 Vcc 10K PAD_GPIO_PM12(EDID_WP)
2
A1 WP
7
Sheet 1 to 4
3 6 R109 33
4.7K
R234

A2 SCL SCL
R110 33
4
Vss SDA
5

C103
100n
R105
SDA

APPROVED BY
XOCECO
0
XIAMEN OVERSEAS CHINESE
ELECTRONIC CO., LTD.
A B C D E F G H

+3.3V_TUNER

JUMPER

R242
+1.8V_TUNER

0
+3.3V_TUNER
+3.3V_TUNER R239
N101 -B MSD309PX-LF-V1 0

1 R211 R212 C203


GND-D
C206 R203
100p 0
+1.8V_TUNER
JUMPER

4.99K
R254 R213 100n

R229
4.7K
C248
100n
4.7K 4.7K 0 100 DIF_P +3.3V_TUNER
002:C4 L201 IF_P
PCMCIA TS1

R225
002:C5 T_SDA SDA_T C205 GND-D GND-D
C242
R255 STLI1608_R12KT

C241
0 150p C227 C228 C229 C231 1u R230 R256

1n
W21 Y16 C204 100n 1% 100 0
PAD_PCM_D[0] PAD_TS1_D[0] 002:C5 T_SCL SCL_T DIF_M 100n 100n 100n 100n SYS_RESET
U21 AD14 R214 R204 IF_N
PAD_PCM_D[1] PAD_TS1_D[1] JUMPER 002:C4 C207
U19 AD15 100 0

48

47

46

45

44

43

42

41

40

39

38

37
PAD_PCM_D[2] PAD_TS1_D[2] 100p

C249
100n
AD12 AC15
PAD_PCM_D[3] PAD_TS1_D[3] GND-D GND-D GND-D
AC12 AC16 GND-D

SIGN1837
VDDA

VDDC

GND

VDDA

REXT

VDDC

VDDC

VREFP

VREFN

VDDC

VI2C

RESET
AD13 PAD_PCM_D[4] PAD_TS1_D[4] Y17 GND-D +3.3V_TUNER
Y12 PAD_PCM_D[5] PAD_TS1_D[5] AB17

C230
PAD_PCM_D[6] PAD_TS1_D[6]

1n
AA11 AB19 @pinCo GND-D
PAD_PCM_D[7] PAD_TS1_D[7] Y18 X201 1 36
PAD_TS1_CLK IF-10S C225 C226 L203 VDDA GND
Y24 AE16 56p
Y22 PAD_PCM_A[0] PAD_TS1_VLD AB16 39p 12nH
GND-D 2 35
1
PAD_PCM_A[1] IN1 SDA

CS0603-R27J-S
AB22 PAD_TS1_SYNC CS0603-12NJ-S SDA_T
AA22 PAD_PCM_A[2] L202 3 34
+5V_TUNER GND 270nH GND SCL SCL_T
AA20 PAD_PCM_A[3] N201 L204
PAD_PCM_A[4] FSA4159 +5V_TUNER_A 390nH 4 33 +1.8V_TUNER
Y21
PAD_PCM_A[5] TS0 C232 CS0603-R39J-S IN2 VDDD

C253
AA18

C251

10p
10p
PAD_PCM_A[6] R205 R206 1 6 120p 5 32 C255
AA19 U20 1K
PAD_PCM_A[7] PAD_TS0_D[0] TS_D0 10K IFAGC_D B1 S RF_SEL +3.3V_TUNER_2 GND EXTREF NC 100n
AA16 V20 IF_AGC L205
PAD_PCM_A[8] PAD_TS0_D[1] TS_D1 RFAGC_A 2 5 16V 100n 6 31

GND-D
AA14 R19 GND-D

XC5200C
TS_D2 002:C4

R207
PAD_PCM_A[9] PAD_TS0_D[2] GND Vcc EXTCK X1

N204
AA12 AE13 C211 820nH

0
PAD_PCM_A[10] PAD_TS0_D[3] TS_D3 22n 3 4 C257 7 30 GND-D
Y15 AC13 C233 GND-D

2 AA17
AA15
AE14
PAD_PCM_A[11]
PAD_PCM_A[12]
PAD_PCM_A[13]
PAD_TS0_D[4]
PAD_TS0_D[5]
PAD_TS0_D[6]
Y11
AB11
AB13
TS_D4
TS_D5
TS_D6
RF_AGC
002:C4
Close to 309
GND-D
RFAGC_A B0 A IFAGC
100n 8
GND

VDDA
GND-D
GND

X2
29 G201

PAD_PCM_A[14] PAD_TS0_D[7] TS_D7 9 28 32MHz


Y20 Y19 GND-D GND-D
PAD_PCM_RESET PAD_TS0_CLK Y23 TS_CLK VDDA SEL C250 C254
R238 C234 30p 30p
PAD_TS0_VLD TS_VAL 0 10 27
AD16 W20 100n
PAD_PCM_IRQA_N PAD_TS0_SYNC TS_SYNC VDDC NC
Y13
Y14 PAD_PCM_OE_N 11 26
PAD_PCM_IORD_N GND VDDC +1.8V_TUNER
AA13 R260 GND-D
AC14 PAD_PCM_CE_N 0 R240 0 12 25

TESTMODE NC
AB23 PAD_PCM_WE_N FRONT END +1.8V_TUNER VDDC NC C252
100n
PAD_PCM_CD_N JUMPER
AB20 AA3 C235
PAD_PCM_WAIT_N PAD_IP DIF_P 002:F4
AB14 AA2 N202 100n

VDDC

VDDA

VAGC

VDDA

VDDC

VDDA

VDDD
PAD_PCM_IOWR_N PAD_IM DIF_M 002:F4 +5V +5V_TUNER +5V +3.3V_TUNER +3.3V_TUNER +3.3V_TUNER_2 +5V_TUNER

VIF

SIF

GND

GND
AA21 R210 GND-D
PAD-PCM_REG_N 51 AZ1117-3.3
Y3 C201 100n R201 2.2K 3 2 R259
PAD_QP Y2 C202 IN OUT 0
100n R202 2.2K GND-D

13

14

15

16

17

18

19

20

21

22

23

24
PAD_QM GND C260
Y25 C208 C214 C224

100u
C215
100n

C212

C213
100n
1 R250

16V
PAD_PCM2_CE_N +3.3V_TUNER_2

10u
AB1 100n C209 220u C221 C223 220u
PAD_VIFP 100n 100n +3.3V_TUNER_1 390
AA1 100n 16V 16V R252
PAD_VIFM +5V_TUNER +5V_TUNER_A C246 R243 0 GND-D 47
100n +3.3V_TUNER GND-D 2 IF_P

0
AB2 R630 MMBT3906LT1
PAD_SIFP 0 C243 C244 JUMPER
AB3 GND-D V203

R258
NAND FLASH PAD_SIFM +3.3V_DE
100n 100n +1.8V_TUNER 1
3
JUMPER
T21 AD3

GND-D
IF_AGC GND-D R244 0
T19 PAD_PF_ALE PAD_IFAGC AE3 002:G5
GND-D GND-D
3 RF_AGC GND-D
4.7K
R236

P21 PAD_PF_AD[15] PAD_RFAGC_TAGC 002:F2 C247 C256


PAD_PF_CE0Z 100n 100n
P20

+3.3V_TUNER_1
R237 +5V_TUNER
R20 PAD_PF_CE1Z AC4 100
T20 PAD_PF_OEZ PAD_TGPIO0(RF_AGC_CTRL) AD2 RF_SEL N203
PAD_PF_WEZ PAD_TGPIO1(DEMOD_RESET) SYS_RESET +3.3V_TUNER +3.3V_TUNER AS1117-1V8 GND-D GND-D
P19 AD4 +1.8V_TUNER R257 +1.8V_TUNER R227
PAD_F_RBZ PAD_TGPIO2(TUNER_SCL) T_SCL 002:H5 0 0 C261
AE4 2
4 100n
PAD_TGPIO3(TUNER_SDA) T_SDA 002:H4 3IN OUT R251
R629 R231 R226 1% 390
10u GND
1 0 0 1K 0
10u C240 R253
C222 C236 C238 C239 IFAGC 47
220u R228
C216

C217

100n 100n GND-D 2


22p

22p
50V

50V

16V IF_N
MMBT3906LT1
GND-D GND-D 1 V204
C245 3
100n +5V_TUNER_A
GND-D
GND-D GND-D
C259

JUMPER
R241
+3.3V_DE GND-D 100n R248

0
390
R249
R245 47
4.7K

2
RJ07

0 GND-D TV_FAT_IFP
+3.3V_DE +3.3V_DE MMBT3906LT1
CJ07 +5V_TUNER_A 1 V202
1u
RST_DEMO 3
RJ13 RJ15 DJ02
100K 100K
4 +1.2V_DE
RJ16
1K
HMF0603BH05BC

NC
C258
100n R246
390
R247
GND-D

GND-D
47
GND-D 2 TV_FAT_IFN
100K MMBT3906LT1
RJ17 1 V201
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55

GND-D 3
RJ01
TEST1
TEST0
DBGSEL
RESETN
VDD12_68
VDD33_67
PWM1
VDD33_65
DBGBUS10
VDD33_63
DBGBUS11
DBGBUS12
VDD33_60
VDD33_59
NC_58
VDD12_57
NC_56
NC_55

33
TS_SYNC GND-D
+1.2V_DE +3.3V_DE +3.3V_DE +1.2V_DE
TS_VAL RJ18
100K +3.3V +3.3V_DE +3.3V_DIV +1.2V-Core
1 54 +1.2V_DE
TS_CLK 2 TSPSYNC DBGBUS13 LJ01 LJ04 LJ06
53 STBH2012-221PT SGMI2012-2R2KT STPB3216-380PT
RJ02 TSBVLD DBGBUS14
3 52 RJ19
GND-D 33 TSBCLK VDD12_52
4 NJ01 51 100K
TS_D7 TSB7 VDD33_51 CJ09 CJ10 CJ11 CJ13 CJ16 CJ19 CJ22 CJ24 CJ26 CJ29 CJ32 CJ34 CJ35
5 50 100n 100n
TS_D6 TXB6 ATBM8848 TESTIO19 10u 100n 100n 100n 100n 100n 100n 100n 100n 1u 100n
6 49
TS_D5 VDD33_6 TESTIO18
7 48 RJ20
TS_D4 TSB5 TESTIO17 100K +3.3V
8 47 NJ02
RJ03 TSB4 DBGBUS15 LJ05
9 46 RJ21 STBH2012-221PT
33 TSB3 DBGBUS16 AP1117-ADJ
10 45 100K 2
4
TS_D3 VDD1210 VDD33_45 3 IN OUT
11 44
TS_D2 TSB2 DBGBUS17 1
12 43 RJ22 RJ25 CJ36 CJ38
TS_D1 TSB1 GND SDAS 100 CJ37 100K CJ39
13 42 100K +1.2V_DE 100u 100u
TS_D0 TSB0 SCLS T_SDA 002:H4 16V 100n RJ27 16V 100n
RJ06 14 73 41

5 IFAGC_D
RJ04 10K 15
16
PWM0
VDD12_PLL
VDD12_41
SDAM
40
39
4.7K +3.3V_DE
RJ23
RJ26
100
T_SCL 002:H5

RJ28
232 CJ03 +3.3V_DIV CLK_REF_OUT SCLM
17 38

0
100n 4.7K
REF_BIAS_EXT

CJ01 18 VDD_DIV I2CINT 37 RJ24 CJ12 CJ14 CJ17 CJ20 CJ23 CJ25 CJ27 CJ30 CJ33
100n REFCLKIO TESTIO10 100n 100n 100n 100n 100n 100n 100n 10u 100n
ADVDD_ADC
REFCLKI1

DVDD_ADC

AVDD_REF

TESTIO16
TESTIO15

TESTIO14
TESTIO13
TESTIO12
TESTIO11

TPJ01
VDD_OSC

VDD1229
QVINP
QVINN
IVINP
IVINN

VDD33

+3.3V_DE
RJ05
33
34
35
36
19
20
21
22
23
24
25
26

28
29
30
31
32
27

1M +1.2V_DE
+3.3V_DE +3.3VA_DE
GJ01 +3.3VA_DE LJ03
30.400MHz STBH2012-221PT
CJ02

CJ06

CJ15 CJ18
50V

50V

CJ21
33p

33p

+3.3VA_DE +3.3V_DE CJ28 CJ31


10u 100n 100n 100n 100n
TITLE: DWG NO.
CJ08
RJ08 RJ10 100n
RJ14
CJ04
10K 10K 45.3K 569KI0801A RF 9222KI5101DL
100n 59K-F
TV_FAT_IFP
CJ05

6 TV_FAT_IFN
100n

DRAWN BY
REV. A1.0
RJ09 RJ11
4.7K 4.7K Sheet 2 to 4

APPROVED BY
XOCECO
XIAMEN OVERSEAS CHINESE
ELECTRONIC CO., LTD.
A B C D E F G H
XB07
JY-3541L-01-030
VGA-LIN CB45 1u RB56 10K
G
CB17 RB10 001:F4
47n 47 CB46 1u RB57 10K
YPBPR-Y_IN VGA-RIN R
NB01 001:H5 001:F4

G
MAX232CSE CB18 RB11 CB47 RB50
R 1n 470 47p 12K CB48 RB58 L
CB01 100n 1 16 YPBPR-SOG_IN
C1+ Vcc +5V-S 47p 12K
CB02 100n 2 15 CB05 100n 001:H5

1 +5V-S
3
CB03 100n 4
5
V+ GND
C1- T1OUT
C2+ R1IN
14
13
12
RS232-TXD
RS232-RXD L
CB29
100p
RB26
75
+3.3V-S
GND-D
G

BU
6 C2- R1OUT 11 CB19 RB12 RB44
GND-D
7 V- T1IN 10 47n 47 UART-RX 33 RB52 RB59
PJ-3514-3P YPBPR-PB_IN

RB83

RB84
CB04 T2OUT T2IN 001:B4;003:A1;005:D1 470 1K
8 9 001:H5

0
100n XB01 VB05 ISP_EN
R2IN R2OUT CB30 RB27 BC847AW 001:B4
100p 75
RB53
RB45 470

R
RB01 CB20 RB13 33
GND-D UART-TX
33 47n 47 001:B5;003:A1;005:D1
UART-RXSTB YPBPR-PR_IN VB06 VB07
001:D6 001:H5 BC847AW BC847AW
RB02 CB31 RB28 VGA-SCL
33 100p 75
UART-TX VGA-SDA
001:B5;003:G1;005:D1 XB02
GND-D

10

15
5
RB03 RCA-386A-02 VGA-VSYNC RB62 100
GND-D
UART-RX 33 001:H4 RB63 100
001:B4;003:G1;005:D1 VGA-HSYNC VCC-VGA
001:H4

14
4

9
RB74 RB78
22K 22K
YPBPR-Y_IN- CB26 47n RB22 68
001:H5 CB50 47n RB64 47 ZB01 220MHz
VGA-B_IN

13
3

8
YPBPR-PB_IN- CB27 47n RB23 68 001:H4
001:H5
CB09 CB28 47n RB24 68 CB51 47n RB65 47 ZB02 220MHz
YPBPR-PR_IN- VGA-G_IN

12
7
2
47n 001:H5 001:H4
CVBS1_IN
2 001:I4
CB10
Near MSD309
VGA-SOG_IN
001:H4
VGA-R_IN
CB52
CB53
1n
47n
RB66
RB67
15K
47 ZB03 220MHz

11
1

6
1u 001:H4
CVBS1-LIN
+5V VCC-VGA RB75 RB79 RB80

XB08
HC1038-15F-3.08
001:F4 XB03 75 75 75
CB11 JY-3541L-01-030
1u CB07 RB15
CVBS1-RIN
001:F4 1u 10K BAV70
YPBPR-RIN L NB07 DB06 GND-D
CB16 001:F4 CAT24C02WI
1u CB23 RB16
CVBS_OUT 47p 12K R
1
A0 Vcc
8

001:I4 10V 2 7 RB47 10K


A1 WP
3 6 RB48 33 RB54 4.7K
G A2 SCL
CB54
CB08 GND-D RB17 4 5 RB49 33 RB55 4.7K
1u 10K Vss SDA 100n
YPBPR-LIN
RB05 Near MSD309 001:F4
100 CB24 RB18 VB04 RB51 4.7K
CVBS-ROUT 47p 12K GND-D ISP_ENGND-D
001:F4 GND-D BC847AW 001:B4
RB07 CB12
100K 180p
GND-D GND-D

GND-D
001:H4
VGA-B_IN- 47n CB56 68 RB68
001:H4
RB06 Near MSD309 VGA-G_IN- 47n CB57 68 RB69
100
CVBS-LOUT
3 001:F4
RB09
100K
CB14
180p
001:H4
VGA-R_IN- 47n CB58 68
Near MSD309
RB70
GND-D XB06
UBA-100/W
G
GND-D
4
USB-D+ RB41 5.1
3
001:B5
USB-D- RB42 5.1
FUB01 2
001:B6
SMD1206L150THWR
+5V-PU 1
1.5A 6 5 4 CB62 G
100u CB64
CB60

RB60

100n
180

NB09 16V
1u

IP4223CZ6
SPDIF
001:F5 1 2 3
RB61
120

GND-D
OR GND-D

RB32 Near MSD309 CB44


1K 1u
HPAMP-LOUT
RCA-103A-OR 001:F4
GND-D
+5V XB04 RB35 CB40

4 200K 3.3n
100n
CA04
16V

GND-D
RA05
10K

RA27 CA02
200 1u RA30 CA03
SPDIF VA06
001:F5 BC847AW 75 1u 16V +3.3V
10V
RA28

10V
300

+3.3V 47u
LB01
RA06

RA29
10K

CB37
47

+5V-PU GND-D
22uH RB76
4.7K
RA25

1K

5
RA26 HP-DCT-

100n
CB42
100u
CB38
CB49

10V
4.7K VA05 001:D5
NA03

VCC

OUT2

BIAS

IN2
SPDIF_CL 100u
BC847AW CM1213-08MS
1 10 L
2 CH1 CH8 9 10V
+5V-HDMI3

BH3547F
+5V G2
3 CH2 CH7 8

NB08
4 CH3 VP 7
GND-D
R
CB55
5 CH4 CH6 6 G5
VN CH5 100u
XA01

OUT1

MUTE

IN1

GND
HDMI ST-113

4.7K
RB43
RA09 10V XB05
10 1 GND-D
001:E5 HDMI3-RX2+ 2

4
5 001:E5
001:E5
001:E5
HDMI3-RX2-
HDMI3-RX1+
HDMI3-RX1-
3

5
4

RB37
RB38
100K

CB32
6

10V

1u
RA10 4.7K VB03
10 7 HP-MUTE-
001:D5 BC847AW
001:E5 HDMI3-RX0+ 8 DB04 GND-D
001:E5 HDMI3-RX0- 9 LL4148
001:E5 HDMI3-RXC+ 10
LL4148
DB05

001:E5 HDMI3-RXC- 11 +5V +12V_A


RB31Near MSD309 CB43
12 1K 1u
HPAMP-ROUT
1K 2

001:E5;003:A2;003:A4 HDMI-CEC 13
001:F4
1
RB81

14 RB36 CB41
001:E5 HDMI3-SCL 15 RB34 200K 3.3n
001:E5 HDMI3-SDA 16 4.7K
1 1

VB02
2 4.7K 1

17
2

+5V +5V-HDMI3 MMBT3906LT1 GND-D


RB82

+5V-HDMI3 18 CB66 DB03


+3.3V +5V-HDMI3 +5V-HDMI3 19 100n LL4148
1 2
2

BAV70
NA01
CAT24C02WI
DA01 TITLE: DWG NO.
CB39
470u

16V

1 8
RA17 RA19 RA23
1K 1K 1K
2
A0

A1
Vcc

WP
7 RA01 10K 569KI0801A
3
A2 SCL
6 RA02 33 RA13 4.7K
CA01
RA21
10K GND-D AV Interface 9222KI5101DL
4 5 RA03 33 RA14 4.7K HDMI3-HP VA03
Vss SDA 100n
001:E5 BC847AW

6 VA01 RA04 4.7K DRAWN BY


REV. A1.0
ISP_EN
BC847AW 001:B4 Sheet 3 to 4

APPROVED BY
XOCECO
XIAMEN OVERSEAS CHINESE
ELECTRONIC CO., LTD.
A B C D E F G H
+5V-S
+3.3V-S
+5V
+5V-S
+3.3V-S X102 R193 X103 X104 +3.3V-S
1K R196 TJC10-04A +3.3V-S
X101 R195 +3.3V
TJC3S-13AW R178 1 10K 1K 1
1 +3.3V

R209
1K V107

C143
100n
R184 LED 001:B4

1K
R181 BC847AW
1 10K 1K 2 2 R208
V102 BL_SW- GND-D 2 5.6K

R175
2.2K
C137 R197 R199 R200 LOGO_BL
BC847AW 001:D6 4.7K 4.7K UART-RX 1%
2 100n 3 +5V-S 33 3 KEY 001:B4
10K 3 001:B4;003:A1;003:G1

C144
R191

33p
1K R194 R198
3 +5V-S 4 IR 33 UART-TX

1 4 +5V
GND-D
+5V
+3.3V
5
R192
+3.3V
C140
39p
GND-D
001:B5 4

GND-D
001:B5;003:A1;003:G1

GND-D
5 R190
6 4.7K 4.7K
R176 R179 SDA
6 100 1K R185 7 SCL
R182
1K
7 R173
V103
C138 BC847AW
10K
BL_PWM TJC10S-07A
N101 -FMSD309PX-LF-V1
001:B4;004:B2
10K 10u
GND-D L102
8 AO3401A NR6045T150M +1.2V-Core
V106
GND-D +12V_A +12V-AMP
9 S D E22 AC2
C142 C136 F22 VDDC1.2V GND AE1

C141
470u
16V
10 G R187 220u VDDC1.2V GND
100n 100K E21 Y10
16V VDDC1.2V_3 GND
+5V-S F21
11 +5V-S G21 VDDC1.2V_4 V7 RV23 RV24
VDDC1.2V_5 GND 100 22K
+3.3V-S R189 H21 W7 LV01
12 +12V_A R174 R215 GND-D 47K E20 VDDC1.2V_6 GND CV19
10K
NR8040T220M
1K R180 001:D6 F20 VDDC1.2V_7 V8 CV10 CV13 2.2n
R177 VDDC1.2V_8 GND 4.7n 4.7n
13 10K 1K R186 PWR_SW G20 W8
V101 R183 VDDC1.2V_9 GND CV32 +12V-AMP
10K 1K V105 G22 V9 CV20
BC847AW 1 u CV34

47n
V104 PWR_SW

47n
BC847AW VDDC1.2V_10 GND W9 1u RV31
BC847AW 001:D6 C139 GND 18 220u RV27
R188 J10 10K XV01
+5V-S +5V 10u 8.2K 16V 16V

RV21 470
GND-D GND

RV22 470
H20 K10 CV21 GND-D GND-D
+12V-AMP GND-D J20 DVDD_MIUA GND M10 39n CV38 CV35 1

CV11
2 +3.3V

CV14
DVDD_MIUB GND +12V-AMP 330p 220u RV28
C134 C135 N10 10K
220u 220u L601 C619 GND 16V 2
STPB3216-380PT GND-D J21 P10
16V 16V 100n AVDD1P2 GND +3.3V

12

11

10
+2.5V R10

1
GND CV23 +12V-AMP 3
T10 RV05 CV26

BST_A
2 1 1n GND-D

PVDD_A_2
C603 C605 R612

VR_ANA

PLL_FLTP

PLL_FLTM

AVSS

PBTL

OC_ADJ

SSTIMER
GND-D

GVDD_OUT
GND

OUT_A
10K

PVDD_A_3
GND-D GND-D 10u 10u 100K M8 U10 100n CV36
AVDD2P5_ADC GND CV05 4
IN BS M9 V10 16V CV07 220u RV29
N603 L607 AVDD2P5_ADC GND RV17 10u 16V 10K
NR8040T100M W10 0 100n
7 MP2307 3 GND RV06
EN SW +1.2V-Core N8 D11 13 48
10uH AVDD25_REF GND 10K CV37
AVDD PGND_AB_48

BG1608B121
N9 G11 RV30
D602 C629 C634 AVDD25_REF GND GND-D 220u 10K
SK34A 470u 100n H11 14 47 16V

L103
R621 R9 GND J11 A_SEL PGND_AB_47 LV02
8 5 4.3K GND-D RV08 NR8040T220M
AVDD_AU25 GND K11 15 46 GND-D GND-D
SS FB 47
GND MCLK MCLK
GND-D OUT_B
1% P8 L11
P9 AVDD25_MOD GND M11 16 45 +12V-AMP
GND4 COMP RV16
AVDD25_MOD GND N11 10K OSC_RES PVDD_B_45 CV24 CV33
R622 T8 GND P11 RV18 17 44 39n
4 6 C145 AVDD25_PGA GND 18.2K CV28 CV31 RV32 1u
10K R11 DVSSO PVDD_B_44
1% 100n GND 1n 100n 18
C618 U8 T11 18 43
C622 AVSS_PGA GND VR_DIG TAS5711 BST_B

BG1608B121
10n U11 GND-D
33p +3.3V-S GND GND-D CV06 CV09 GND-D CV39
V11 100n 19 42

L104
E9 GND W11 4.7u PDN NV01 BST_C +12V-AMP 330p
C612 R617 AVDD_DVI
AVDD_DVI_E9 GND
100n 1K E10 D12 20 41
F9 AVDD_DVI GND E12 LRCLK PVDD_C_41
AVDD_DVI GND GND-D
F10 F12 21 40 CV27 CV29 CV30
GND-D AVDD_DVI GND GND-D
+12V-AMP G9 G12 SCLK PVDD_C_40 39n 1n 100n

3 L602
STPB3216-380PT
GND-D
G10
AVDD_DVI

AVDD_DMPLL
GND
GND
GND
H12
J12
K12
LRCLK
SCLK
47
47
47
RV10
RV11
RV12
22

23
SDIN OUT_C
39

38 GND-D
L606 GND SDIN
2

C604 C606 R609 C617 +1.8V-DDR2 H9 L12 33 RV13 SDA PGND_CD_38


10u 100K 100n SLF7045T-330MR82-PF AVDD3P3_ADC GND SDA
10u H10 M12 RV14 24 37
IN BS 33uH AVDD3P3_ADC GND SCL 33 GND-D
N12 SCL PGND_CD_37

PVDD_D_34

PVDD_D3_5
GND

GVDD+OUT
K9 P12

CV04

CV08
7 3

50V

50V
33p

33p
2
1

AVDD_AU33 GND R12


EN SW

RESET

STEST

BST_D

OUT_D
GND

DVDD

DVSS

AGND

VREG

RV26
J9 T12

GND
N602

3K
R620 AVDD_EAR33 GND U12
MP2309 10K GND +12V-AMP
8 5 1% V12

25

26

27

28

29

30

31

32

33

34

35

36
FB GND W12 GND-D GND-D
SS GND-D
R619 GND D13 GND-D CV22 CV25
10K +3.3V GND E13 100n 1n
GND COMP 1% C628 C631 +5V

CV18
GND

16V

1u
10u 10u E19 F13 X401
F19 VDDP GND CV17 PHB-2x20-2.0
+3.3V
4

VDDP 100n
H13 +3.3V GND-D
GND RV15 1 2
C616
C620

DV04
39n

G18 J13
16V

CV02
47p

10K GND-D VDD-P VDD-P

RV25
C610 AVDD_LPLL_MEMPLL GND 1 2
LL4148

3K
100n K13 100n
GND L13 GND-D 3 4
RV03 CV15 CV16 3 4
GND 16V
R616

M13 1K VV02 100n


1K

N606 GND 10u 5 6


N13 STB_AMP +5V
AS1117-3V3 +3.3V-S +1.8V-DDR2 GND 001:B4 GND-D 5 6
P13 CV03
GND DV02 RV04 100n 7 8
RV09 001:D4 RXO0-
GND-D +5V-S IN OUT
E17
AVDD_DDRA_E17 GND
R13 LL4148 3K 10K GND-D 7 8
E18 T13 001:D4 RXO0+
C633 C639 RV20
4 +5V N601
AZ1084S-3.3
+3.3V 100u
16V
C636
100n
GND C638
100n
100u
16V
F17
F18
G17
AVDD_DDRA_E18
AVDD_DDRA_F17
AVDD_DDRA_F18
GND
GND
U13

D14
+12V_A +5V
GND-D
RV19
1K
47K 001:D4
001:D4
001:D4
RXO1-
RXO1+
RXO2-
9

11
9 10
10

12
Vin Vout +2.5V RV07 RESET_AMP 11 12
C601 C615 AVDD_DDRA_G17 GND E14 001:D4 RXO2+
C602 C613 D601 GND-D RV01 RV02 3K CV12
100u GND 220u G16 GND F14 DV03 100n 001:D4 RXOC- 13 14
16V 100n 100n 16V 1N4007 AVDD_DDRB_G16 GND
4.7K 1K 13 14
H16 G14 LL4148 001:D4 RXOC+
+3.3V AVDD_DDRB_H16 GND 001:D4 RXO3- 15 16
C640 H17 H14 VV01 15 16
C627 C630 R625 R626 R627 R628 100u AVDD_DDRB_H17 GND 001:D4 RXO3+
100n 100n 390 390 390 390 J16 J14 MMBT3906LT1 GND-D
16V AVDD_DDRB_J16 GND SCL R401 0 001:D4 RXO4- 17 18
J17 K14 DV01 001:A6;001:B5;005:C2;005:E1;005:E3 SCL 17 18
+12V-AMP AVDD_DDRB_J17 GND LL4148 001:D4 RXO4+
L603 L14
C623 GND 19 20
STPB3216-380PT GND-D 100n GND-D M14 SDA R402 0
GND 001:A6;001:B5;005:C2;005:E1;005:E3 SDA 19 20
N14 CV01
GND R403 10K 21 22
R615

220u
100K

C609 C611 2 1 L10 P14 +3.3V 21 22


10u 10u DVDD_NODIE GND R14 16V R404 0
+5V_USB +5V GND
IN BS T14 R405 10K 001:D4 RXE0- 23 24
N604 L608 L610 GND-D 23 24
NR8040T100M STPB3216-380PT C146 GND U14 R406 0 001:D4 RXE0+
7 MP2307 3 2.2u GND 001:D4 RXE1- 25 26
EN SW 10uH 25 26
001:D4 RXE1+
220u
C637

D15 GND-D
16V

C632 C635 GND R407


10u 10u E15 22 001:D4 RXE2- 27 28
R623 GND-D GND 27 28
F15 LVDS_I/O1 001:D4 RXE2+
8 5 45.3K GND R408
G15 22 001:D4 RXEC- 29 30
SS FB 29 30
1% N19 GND H15 LVDS_I/O2 001:D4 RXEC+
M19 GND_104 GND J15 001:D4 RXE3- 31 32
GND4 COMP GND_105 GND 31 32
L19 K15 001:D4 RXE3+
4 6 R624 K19 GND_106 GND L15 001:D5 RXE4- 33 34

5 10K
1% N20 GND_107
GND_108
GND
GND_132
M15 001:D4 RXE4+
35
33 34
36
C624
47p

C621 M20 N15 35 36


10n L20 GND_109 GND_133 P15
K20 GND_110 GND_134 R15 37 38
GND_111 GND_135 37 38
C614 R618 N21 T15
100n 4.7K M21 GND_112 GND_136 U15 39 40
GND_113 GND_137 39 40 K401
+12V-AMP L21
K21 GND_116 U16
L605
STPB3216-380PT GND-D N22 GND_117 GND_85 T16
M22 GND_118 GND_86 R16
GND_119 GND_87 GND-D
L22 P16
L604 K22 GND_120 GND_88 N16
STPB3216-380PT J22 GND_121 GND_89 M16
+3.3V +5V_USB GND_122 GND_90
H22 L16
+3.3V
R613
47K C625 VDD-P
GND_123 GND_91
GND_92
K16 BOT
100n F16 +1.2V-Core +3.3V
R 6 0 5 R607 GND_93 +1.2V-Core
R601 1 K 10K U18 E16 +3.3V
R603 V603 T18 GND_124 GND_94 D16
1K 10K TITLE: DWG NO.
PNPWR_SW V601 BC847AW R18 GND_125 GND_95 K17

100n

100n

100n

100n

100n

100n
C157

C159

C161

C163

C165

C167
C607 R610
001:D6 B C 8 4 7 A W 10u 1 8 +5V-PU P18 GND_126 GND_96 L17 C153
8.2K C147 C150 C151 C155 C156
+5V_USB S2 D2_8 GND_127 GND_97 100n
GND-D 2 7
N18
GND_128 GND_98
M17 100n 100n 100n 100n 100n
569KI0801A InternalInterface
+3.3V GND-D G2 N605 D2_7
M18
GND_129 GND_99
N17
POWER & Audio AMP 9222KI5101DL
L18 P17 GND-D GND-D
+3.3V 3 AO4803A 6 K18 GND_130 GND_100 R17 GND-D GND-D
+3.3V-S +1.8V-DDR2 +2.5V
R614
47K

S1 D1_6 GND_131 GND_101 T17 +1.8V-DDR2


R606

6 4 5 GND_102 +3.3V-S
1K

R608 U17
A1.0
R602

10K G1 D1_5 GND_103 REV.


1K

100n

100n

100n

100n

100n
C158

C160

C162

C164

C166
R604 V604
10K V602 BC847AW GND-D GND-D DRAWN BY
8.2K
R611

C152
C608

USB_SW C148 C149 C154


10u

BC847AW 100n 100n 100n 100n Sheet 4 to 4


C626
100n GND-D GND-D GND-D
GND-D GND-D
GND-D GND-D
APPROVED BY
XOCECO
XIAMEN OVERSEAS CHINESE
ELECTRONIC CO., LTD.
A B C D E F G H

D[0-7]
TP1

1
5V
PAD1

D[6]

D[7]

D[0]

D[1]

D[2]

D[3]

D[4]

D[5]
X1
RESERVE
1 V33
VCC

GND 2

37

36

35

34

33

32

31
40

39

38
POWER

V33
IRQ 3

CIN0

THD0

THD1

NC
PAD2

GPIO0

GPIO1

GPIO2

GPIO3

GPIO4
DVSS
GND/THD 4 KEY INPUT

10K

10K
R5

R6
R1 NC
0 SCL
5 PAD3 1 30
SCL R2 NC CIN1 GPIO5
MENU R7
0 SDA
6 2 29 3.3K
SDA PAD8 CIN2 GPIO6
5V CH-
3 28

D[0-7]
LED1 CIN3 GPIIO7
5V D[0] PAD4 5.6K
4 27

12p

12p
R13

IT7230AFN
C1

C2
CH+ CIN4 INT#
5 26 SDA SDA
CIN5 SDA
VOL- PAD5

N2
LED2
2 D[1] 6
CIN6 SCLK
25
SCL

GND
PAD6 7 24
CIN7 ADD0
LED3
D[2] 8 23
CIN8 ADD1
R8
9 22 10K
CIN9 GPIO8 V33
R9 R14
10 21 20K 4.7K
LED4 D[3] CIN10 GPIO9

VSHILD

GPIO12

GPIO11

GPIO10
VBIAS
CIN11

CIN12

AVSS

AVCC

DVCC
LED5
D[4] R10

13

14

15

16

17

18

19

20
2K

11

12
R11

100n
1K

C6
LED6
D[5]

100
R4
R12
0
AVCC V33

100p
5V

C5
LED7 KEY

AVCC
D[6] R3 NC
0

100n
C7
3

100n
V33 AVCC

C8
LED8 TP2
N1 L1
D[7]
AS1117-3V3 BG1608B121
IN OUT

10u 5V
PAD7

C3

C4
1u
D[0-7] VOL+

Touching Key
4 R904
1.1K
LED901
HFT503MPBR-1

R902 R B
3.3K
X901 V901
TJC10-04AWT BC847AW R905
2K
5 1
GND-D GND-D
2 N902
+5V-S R903 HRM138BB5117
47 Vcc
3
GND
Vout
4 TITLE: DWG NO.
C903
22uF C904 9232KH4601DL
10V 100n IR + TOUCH KEY
6
IR GND-D
GND-D
DRAWN BY
REV.
Sheet8
A1.0
to 9

APPROVED BY
XOCECO
XIAMEN OVERSEAS CHINESE
ELECTRONIC CO., LTD.
Power board
Backlight board
APPENDIX-A: Main assembly 9222KI5111 LED-22XZ11F
NAME NO. MAIN COMPONENT AND IT'S NO.
N101 MSD309PX-LF-SV 5270309003

N102, N103 NT5TU32M16DG_AC 5273216001


Main
XI6KI00501A0 NB08 BH3547F 5273547001
board
N204 XC5200C 5275200002

NV01 TAS5711 5275711001

IR board XI635KH00800
Key
XI635KH00801
board
Power
XI6KI00520A0
board
Remote
XI6010900802 RC-908-0A
control
Panel XI5203228206 CLAA215FA04 V4
APPENDIX-B: Exploded view (LED-22XZ11F)
PART LIST OF EXPLODED VIEW

REF.No. DESCRIPION
1 Front cabinet assembly
2 Display panel
3 Main board assembly
4 GND reed
5 Main frame assembly
6 Power board assembly
7 Back cover assembly
8 Adjusting clasp
9 Power cord
10 Power cord clip
11 Pedestal assembly
12 Standing pole assembly
13 Bracket for power cord clp
14 Touching key board assembly
15 Rotor assembly
16 Speaker assembly
17 IR assembly
18 Light-guided pole
19 Interface baffle (side)

Note: Design and specification are subject to change without notice.


PART LIST
LED-22XZ11F ver.1.0
REF.No. PARTS No. DESCRIPION Q'TY REMARK
1 XI6622510090 Front cabinet assembly 1
2 XI5203228206 Display panel 1 LB_CLAA215FA04 V4
3 XI6KI00501A0 Main board assembly 1
4 XI592302860B GND reed 2
5 XI615328301C Main frame assembly 1
6 XI6KI00520A0 Power board assembly 1
7 XI672272P03A Back cover assembly 1
8 XI5720124000 Adjusting clasp 1
9 XI5602510001 Power cord 1
10 XI572011201C Power cord clip 1
11 XI6151204020 Pedestal assembly 1
12 XI6156103020 Standing pole assembly 1
13 XI58B0A4231A Bracket for power cord clp 1
14 XI635KH00801 Touching key board assembly 1
15 XI615811500A Rotor assembly 1
16 XI617081500B Speaker assembly 1
17 XI635KH00800 IR assembly 1
18 XI570031901D Light-guided pole 1
19 XI5810F72410 Interface baffle (side) 1
20 XI6010900802 Remote control 1
21 XI5944039500 User manual 1

Only the parts in above list are used for repairing.


Other parts except the above parts can't be supplied.
Appendix: Installing the Stand
If the stand is provided, please read these instructions thoroughly before attempting this installation.
You must install your TV into the stand in order for it to stand upright on a cabinet or other flat surface. If you intend
to mount your TV on a wall or other vertical surface, you must remove the stand column.
Cautions:
Make sure that you handle your TV very carefully when attempting assembly or removal of the stand. If you are not
sure of your ability to do this, or of your ability to use the tools necessary to complete this job, refer to a professional
installer or service personnel. The manufacturer is not responsible for any damages or injuries that occur due to
mishandling or improper assembly.
The speaker is not intended to support the weight of your TV. Do not move or handle your TV by the speaker. This
can cause damage to your TV that is not covered by the manufacturer's warranty.
Before attempting assembly or removal of the stand, unplug the AC power cord.

Installing the stand


To install the stand:

1. Carefully place your TV screen face-down on a cushioned, clean


surface to protect the screen from damages and scratches.
2. Secure the stand to the TV with the three provided screws.

Adjusting the viewing angle To adjust the viewing angle:


Backward Forward
! Tilt the screen forward or backward.

Caution: When adjusting the viewing angle, be careful not to tip over
your TV.

Installing a wall-mount bracket Note: If you are mounting the TV and plan on using the
(not provided) back inputs, a low profile wall mount may not work with
your TV.

To attach your TV to a wall-mount bracket (not provided)

1. Carefully place your TV screen face-down on a cushioned, clean


NOTE: surface to protect the screen from damages and scratches.
The appearance of this product in 2. Remove the two screws holding the TV to its stand column.
these illustrations may differ from 3. Remove the stand column.
your actual product, and is for 4. Secure the wall-mount bracket to the back of your TV using the four
comparative purposes only. screws provided with the bracket.
WALL MOUNTING INSTRUCTIONS
Safety Precautions:
1. Be sure to ask an authorized service personnel to carry out setup.
2. Thoroughly read this instruction before setup and follow the steps below precisely.
3.The wall to be mounted should be made from solid materials. Only use accessories supplied by the manufacturer.
4.Very carefully handle the unit during setup. We are not liable for any damage or injury caused by mishandling or improper installation.
5.Be sure to place the unit on a stable and soft platform which is strong enough to support the unit.
6.Do not uplift the speaker when moving the display. The appearance of the unit may different from the actual ones.
7.Design and specifications are subject to change without notice.
8. Retain these instructions for future reference.

Note: All the wall mounting parts are optional and may be unavailable in your model.
Below we will show you how to mount the Display on the wall using our company’s wall mounting components.

1 2 Screw 4pcs expansion bolts to fix If your wall is a wooden structure, please 3 Use the 4pcs M4 screws to fix the wall
Take out these parts from the box. the wall mounting bracket on the fix the wall mounting bracket on the wall
wall. with 8 pcs wood screws. mounting connector to the rear of the
Wall Mounting display unit.
Component
(including bracket
and connector) Wall Wall

Expansion Bolt
Wood Screw Wall Mounting Connector
Wall Mounting Bracket Wall Mounting Bracket
M4 Screw
Fig. 1 Fig. 2a Fig. 2b Fig. 3

4 Fully insert the two insertions on the wall mounting connector into the 5 Use screwdriver to revolve the Clasper to the Positioner
locating grooves on the wall mounting bracket from top to bottom end. following the direction of the arrow.

Clasper

Positioner

Fig. 4 Fig. 5
August 2011

S-ar putea să vă placă și