Documente Academic
Documente Profesional
Documente Cultură
Applications
• Instrumentation Ordering Information
• Multiplexers Part # Description
• Data Acquisition LCA110 6-Pin DIP (50/Tube)
• Electronic Switching LCA110S 6-Pin Surface Mount (50/Tube)
• I/O Subsystems LCA110STR 6-Pin Surface Mount (1,000/Reel)
• Meters (Watt-Hour, Water, Gas)
• Medical Equipment—Patient/Equipment Isolation
• Security Pin Configuration
• Aerospace
• Industrial Controls AC/DC Configuration DC Only Configuration
1 6 1 6
+ Control Load + Control + Load
2 5 2 5
- Control Do Not Use - Control - Load
3 4 3 4
NC Load NC
Switching Characteristics of
Normally Open Devices
Form-A
IF
90%
ILOAD 10%
ton toff
Pb e3
DS-LCA110-R12
www.ixysic.com 1
INTEGRATED CIRCUITS DIVISION LCA110
R12
2 www.ixysic.com
INTEGRATED CIRCUITS DIVISION LCA110
30
20 20
25
20 15 15
15 10 10
10
5 5
5
0 0 0
1.17 1.19 1.21 1.23 1.25 0.82 0.84 0.86 0.88 0.90 0.92 0.94 0.285 0.295 0.305 0.315 0.325 0.335 0.345
LED Forward Voltage Drop (V) Turn-On Time (ms) Turn-Off Time (ms)
Typical IF for Switch Operation Typical IF for Switch Dropout Typical On-Resistance Distribution
(N=50, IL=120mADC) (N=50, IL=120mADC) (N=50, IL=120mADC)
25 25 35
30
20 20
Device Count (N)
25
15 15 20
10 10 15
10
5 5
5
0 0 0
0.39 0.65 0.91 1.17 1.43 1.69 1.95 0.39 0.65 0.91 1.17 1.43 1.69 1.95 20.2 20.4 20.6 20.8 21.0 21.2 21.4
LED Current (mA) LED Current (mA) On-Resistance (:)
30
Device Count (N)
25
20
15
10
0
427 430 433 436 439 442
Blocking Voltage (VP)
1.8
0.6
1.6 1.6
Turn-On Time (ms)
1.4 0.5
1.4 1.2 0.4
I F =50mA 1.0
1.2 0.8 0.3
I F =10mA
0.6 0.2
I F =5mA
1.0 0.4
0.1
0.2
0.8 0 0
-40 -20 0 20 40 60 80 100 120 0 5 10 15 20 25 30 35 40 45 50 0 5 10 15 20 25 30 35 40 45 50
Temperature (ºC) LED Forward Current (mA) LED Forward Current (mA)
*The Performance data shown in the graphs above is typical of device performance. For guaranteed parameters not indicated in the written specifications, please contact our application
department.
R12 www.ixysic.com 3
INTEGRATED CIRCUITS DIVISION LCA110
On-Resistance (:)
3.5 0.7 IF=10mA
40
3.0 0.6
2.5 0.5 30
2.0 0.4 IF=5mA
I F =5mA 20
1.5 0.3
1.0 0.2
10
0.5 0.1
I F =10mA
0 0 0
-40 -20 0 20 40 60 80 100 -40 -20 0 20 40 60 80 100 -40 -20 0 20 40 60 80 100
Temperature (ºC) Temperature (ºC) Temperature (ºC)
2.0 2.0 50
1.5 1.5 0
0 0 -150
-40 -20 0 20 40 60 80 100 -40 -20 0 20 40 60 80 100 -3 -2 -1 0 1 2 3
Temperature (ºC) Temperature (ºC) Load Voltage (V)
Maximum Load Current Typical Blocking Voltage Typical Leakage vs. Temperature
vs. Temperature vs. Temperature Measured Across Pins 4&6
210 430 0.016
DC Configuration
200 0.014
425
Blocking Voltage (VP)
180
Load Current (mA)
0.012
420
Leakage (PA)
160 I F =10mA
0.010
140 I F =5mA 415
0.008
120 410
0.006
100
AC/DC Configuration 405
80 I F =10mA 0.004
60 I F =5mA 400 0.002
0 395 0
-40 -20 0 20 40 60 80 100 120 -40 -20 0 20 40 60 80 100 -40 -20 0 20 40 60 80 100
Temperature (ºC) Temperature (ºC) Temperature (ºC)
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
10Ps 100Ps 1ms 10ms 100ms 1s 10s 100s
Time
*The Performance data shown in the graphs above is typical of device performance. For guaranteed parameters not indicated in the written specifications, please contact our application
department.
R12
4 www.ixysic.com
INTEGRATED CIRCUITS DIVISION LCA110
Manufacturing Information
Moisture Sensitivity
All plastic encapsulated semiconductor packages are susceptible to moisture ingression. IXYS Integrated
Circuits Division classified all of its plastic encapsulated devices for moisture sensitivity according to
the latest version of the joint industry standard, IPC/JEDEC J-STD-020, in force at the time of product
evaluation. We test all of our products to the maximum conditions set forth in the standard, and guarantee proper
operation of our devices when handled according to the limitations and information in that standard as well as to any
limitations set forth in the information or standards referenced below.
Failure to adhere to the warnings or limitations as established by the listed specifications could result in reduced
product performance, reduction of operable life, and/or reduction of overall reliability.
This product carries a Moisture Sensitivity Level (MSL) rating as shown below, and should be handled according
to the requirements of the latest version of the joint industry standard IPC/JEDEC J-STD-033.
ESD Sensitivity
This product is ESD Sensitive, and should be handled according to the industry standard JESD-625.
Reflow Profile
This product has a maximum body temperature and time rating as shown below. All other guidelines of J-STD-020
must be observed.
Board Wash
IXYS Integrated Circuits Division recommends the use of no-clean flux formulations. However, board washing to
remove flux residue is acceptable. Since IXYS Integrated Circuits Division employs the use of silicone coating as
an optical waveguide in many of its optically isolated products, the use of a short drying bake could be necessary
if a wash is used after solder reflow processes. Chlorine- or Fluorine-based solvents or fluxes should not be used.
Cleaning methods that employ ultrasonic energy should not be used.
Pb e3
R12 www.ixysic.com 5
INTEGRATED CIRCUITS DIVISION LCA110
MECHANICAL DIMENSIONS
LCA110
8.382 ± 0.381
7.239 TYP PCB Hole Pattern
(0.330 ± 0.015) 2.54 ± 0.127 (0.285 TYP)
(0.100 ± 0.005)
6 - 0.800 DIA.
(6 - 0.031 DIA.) 2.540 ± 0.127
9.144 ± 0.508 (0.100 ± 0.005)
6.350 ± 0.127 (0.360 ± 0.020)
(0.250 ± 0.005)
7.620 ± 0.127
(0.300 ± 0.005)
7.620 ± 0.254
Pin 1 (0.300 ± 0.010)
1.651 ± 0.254 0.254 ± 0.0127
(0.065 ± 0.010) (0.010 ± 0.0005) 6.350 ± 0.127 5.080 ± 0.127
(0.250 ± 0.005) (0.200 ± 0.005)
LCA110S
8.382 ± 0.381
0.635 ± 0.127 PCB Land Pattern
(0.025 ± 0.005)
(0.330 ± 0.015) 2.54 ± 0.127
(0.100 ± 0.005) 2.54
(0.10)
4.445 ± 0.254
(0.175 ± 0.010)
Dimensions
1.651 ± 0.254 mm
(0.065 ± 0.010) (inches)
R12
6 www.ixysic.com
INTEGRATED CIRCUITS DIVISION LCA110
P = 12.00 A0 = 10.10
K0 = 4.90 (0.398)
(0.472)
(0.19)
K1 = 3.80 Dimensions
(0.15) User Direction of Feed mm
Embossed (inches)
Carrier
NOTES:
1. All dimensions carry tolerances of EIA Standard 481-2
Embossment 2. The tape complies with all “Notes” for constant dimensions listed on page 5 of EIA-481-2
The products described in this document are not designed, intended, authorized or warranted for use as components in systems intended for surgical implant into the body, or in other
applications intended to support or sustain life, or where malfunction of IXYS Integrated Circuits Division’s product may result in direct physical harm, injury, or death to a person or severe
property or environmental damage. IXYS Integrated Circuits Division reserves the right to discontinue or make changes to its products at any time without notice.
Specification: DS-LCA110-R12
©Copyright 2012, IXYS Integrated Circuits Division