Documente Academic
Documente Profesional
Documente Cultură
supply if current demand exceeds DPS-15- ACU Global Global Global Global
2 3 45 67 8
maximum. Set J1 on EXT and connect to Output Output Output Output
8 7 6 5
separate power source.
O1
N
GND
Optional – Pre-alert
Optional – Pre-alert
Optional – Pre-alert
information.
NEW – The control board may require setting S2 DIP
switches. Refer to the Specifications / Settings sheet. Tape back Pre-alert outputs if using
shields at external sound alert device.
readers. Optional OCB-8 K8 K7 K6 K5
OCB
Pre-alert warns
DPS-15 Power Supply when the door is
Dual linear DC outputs: held open beyond
- ACU output 12 VDC @ 1.2 Amperes Relay
Rev. the half interval of
Shield
- AUX/RDR output 12 VDC @ 1.2 Amperes Normal the combined Door
The total current draw on each output should not exceed 1 Amp Pre- Pre- Pre- Pre- Relay Unlock Time
2 3 45 67 8
Alert Alert Alert
with 200 mA in reserve for accommodating peak current 4 3 2
Alert and the Door Held
1
Open Time. Pre-
operating demands. alert relay is also
O1
N
GND
activated on an
Connect reader shields to ACU enclosure ground lug. “alarm tripped”.
12V
Aux Aux Aux Aux EXT
Output Output Output Output J1
5 6 7 8 ACU
Aux Outputs 5 –
ACU Enclosure 8 connect to 3rd
Ground Lug connect to party devices
READER 4 READER 3 READER 2 READER 1
CONTROL 2 such as alarm
panel, CCTV or
p/n CAS6105 S3 LED ON = door locks
Relay
Cold Water
S2
Energized without readers.
O 1 2 3 4 5 6 7 8 9 10 11 12
K1 K2 K3 K4
CARD
BITS control board is powered
Connect to PSC1 Optional OCB-8 K8 K7 K6 K5
READER PWR up for the first time, press OCB
sockets on CA4500B -
10s 1s
FAIL
- press S3 within 10 S1
Relay
+
FAIL
seconds to load factory Rev.
S4
2 3 45 67 8
Not Not Not Not
O1 2
COMMUNICATION STATUS
AC AC - + FAIL - + - + FAIL AC AC
AUX/RDR BATT AUX/RDR EGND ACU ACU TD1 RD1 TD2 RD2 TD3 RD3 TD4 RD4
O1
N
PSC1
GND
Operating Temperature
41°F to 120°F Enlarged view of
(5°C to 49°C) reader terminal 12V
CONTROL 1
CONTROL 4
HC HC HC HC EXT
Humidity READER X Output Output Output Output J1
TP1
0% to 90% R.H., C1 LED D1 D0 PWR GND
connect to 1 2 3 4 ACU
DPS15
Dual Power Supply TP2
non-condensing (Beep) WHT GRN RED BLK CONTROL 4
TP3
+
TP4 -
TP5
TAMPER (TB3)
SWITCH
Credential records with Extended
GND CTS Entry enabled (Aurora) or Accessibility LED ON =
Relay
DTR
AC AC DCD Feature On (System VII and Vantage) K1 K2 K3 K4
Energized
RD
AUX/RDR ACU
TD trip the HC accessibility output. Refer HC Accessibility
GND
to the Technical Guide for more output connects to
RS-232 (COM4)
information. motorized door
Either two - 16V 40VA or
hardware on Door 2.
16.5V 37VA transformers mounted
externally. ACU Protective Cover IOCB (COM1)
RX
TX Tamper Switch K8 K7 K6 K5
Aux Outputs 1 – 4 connect
on ACU OCB
to 3rd party devices such as
ETHERNET M1 Enclosure alarm panel, CCTV or door
Control Board Current – 130 mA
Primary locks without readers.
Relay
110 VAC Rev.
Fire Contact
Normal
breaks on alarm
The PC109x control board emits an Aux Aux
- Aux Aux
2 3 45 67 8
CONTROL 1 N.C.
7 to 8 AH B) two (2) transformers are not
+
O1
DOOR INPUTS - A COMMON RTE INPUTS - B COMMON AUX INPUTS - C COMMON AUX INPUTS - D COMMON
N
1 2 3 4 1 2 3 4 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 GND
connected
12V
Door Door Door Door EXT
+
Output Output Output Output
Run Mode 1 2 3 4
J1
+ DC
ACU
Common Connect ribbon cable from Supply
-
HDR1 terminal on CIM to H2
terminal on control board. -
Door Contact OCB-8
Current – 230 mA
Door # 1 CIM with Network or Serial
Relays – Form C contacts LED ON =
N.C. Connection (CIM 0) Relay
– 5 A / 30 VDC K1 K2 K3 K4
Energized
Jumper ON J4
– 10 A / 24 VAC
Common Maglock
Program Mode (Fail Safe)
PC with To program NETCOM2P/6P Door
Connect all common cables to COMMON terminals on control board
Door Contact
Communication when plugged into CIM, Output # 1 -
Door # 2 + Door Strike
Manager place a jumper ON J12.
N.C. (Fail Secure)
After programming, remove
jumper from J12 to reset Door Output # 2
Common +
CIM board for Run mode.
to network Diode
(TCP/IP) 1N4004
N.O.
to network J7 -
V+ CAN2 -
Door # 1 Exit Push Button (TCP/IP) (+12 V)
GND
J8 CAN2
HDR1 +
J5
Ethernet COM1 CAN1
J6
EGND
GND
Common N.O. TD1
- Door Lock Cable 18 AWG
CAN1
+
RD1
PIR RTS
½ second pulse CTS RESET
COM1
CIM COM2 CIM 0
DC GND J1
Door # 2 Exit Device Supply
Serial RS-232 Connection GND
Jumper ON J4
TD2
Green
TD1
RD2 J4 J10 J11
J9
Black
J3
RD1 RTS
NETCOM2P or
CTS
Red
Common ground
1 2 1 2
Rx-COM CAN
1 2 1 2
COM CAN-Tx
J2 Fault
(Flashing) - CAT 5
lug CTS - 2 twisted pairs
Aux Input
Aux Input
* Insulate shield with PVC - maximum cable distance first CIM to last CIM -3280 ft (1000 m)
tubing such as Alpha (p/n White & Brown not @ 9600 baud
N.C.
N.C. PVC10516 16 AWG) or Shield* used.
comparable insulator. Bit Rate / Distance CIM with network or serial connection = CIM 0 – jumper ON J4
5 conductor Bit CAN Bus RS-232
Tape back 22 AWG shielded
9600 3280' (999.7 m) 49.2' (14.9 m) See over for more on CIM to CIM CAN Bus connections and
Door contacts, exit devices, or PIRs - 22 AWG cable shield.
19200* 3280' (999.7 m) 49.2' (14.9 m) jumper settings.
N.C. = Normally Closed
57600 984' (299.9 m) 26.2' (7.9 m)
Green
Black
115200* 262' (80 m) 9.84' (3 m) Also refer to the CIM – Setup Guide.
to * not applicable for reverse network communication
PC
CA4500 Control Board – Serial # _________ (Communication address) / NETCOM Device – IP Address ___________________________ Subnet Mask ____________________________
Name Name
Door # 1 ______________________________ Reader # / Direction ______________ AI/SI # 1 _____________________________ AI/SI # 9 ____________________________
Door # 2 ______________________________ Reader # / Direction ______________ AI/SI # 2 _____________________________ AI/SI # 10 ____________________________
Door # 3 ______________________________ Reader # / Direction ______________ AI/SI # 3 _____________________________ AI/SI # 11 ____________________________
Door # 4 ______________________________ Reader # / Direction ______________ AI/SI # 4 _____________________________ AI/SI # 12 ____________________________
AI/SI # 5 _____________________________ AI/SI # 13 ____________________________
AI/SI # 6 _____________________________ AI/SI # 14 ____________________________
AI/SI # 7 _____________________________ AI/SI # 15 ____________________________
AI/SI # 8 _____________________________ AI/SI # 16 ____________________________
Keyscan Inc. A Member of the Kaba Group - CA4500 - 4 Reader Access Control Board - Rev. PC109x 10.15 – Document # KD10003-E
Circuit Board Mounting Locations Communication – Network (TCP/IP)
Host PC with
IOCB (COM1)
Communication RX
Manager TX
CPB/CB COMMS
(COM4)
DPS-15 NETCOM
power
supply
Slave
to network
Optional
H2 H1
OCB-8
Locations Termination Jumpers ON
COMMON AUX INPUTS - E
Ground Lug 17 18 19 20 21 22 23 24
J5 & J6 / J7 & J8
first & last CIM
V+ J7 Orange
(+12V) -
CAN2 CAN2
Optional to network with path/ GND HDR1 J8
+
White Orange
OCB-8 connectivity to PC/server J5
EGND
Ground
CA4500B with Communication
GND CAN1
Blue
Optional Locations J6 -
Control Manager
TD1 CAN1 White Blue
NETCOM* Tamper
Locations Board
Switch
RD1 RESET CIM 0 +
RTS RJ45
SCKT1 Terminal J1
CTS CIM 0
CAN Bus 1 and CAN Bus 2 required for Jack
PC109x Jumper ON J4
reverse network applications GND
J4 J10 J11
TD2 J3 J9
OCB-8
RD2
Bit Rate / Distance RTS NETCOMP B3 B2 B1 B0 Diag J12
CIM Power
Bit CAN Bus RS-232 CTS
Good
or 9600 3280' (999.7 m) 49.2' (14.9 m) PC106x 1 2 1 2
Rx-COM CAN
1 2 1 2
COM CAN-Tx J2 Fault
NETCOM 19200* 3280' (999.7 m) 49.2' (14.9 m)
57600 984' (299.9 m) 26.2' (7.9 m) Slave - Jumper OFF - J3 CAT 5
115200* 262' (80 m) 9.84' (3 m) CAN Bus
* not applicable for reverse network communication
Connect EGND terminal on all CIMs to
ground lugs in ACU metal enclosures.
IOCB (COM1)
Bit Rate / DIP Switch Settings (0 = OFF / 1 = ON) RX
* NETCOM - for side mount, use terminal block only, not 9-pin male connector. NETCOM Bit Rate Control Board CIM TX
H2 H1
V+ J7 Orange
(+12V) -
CAN2
J8 CAN2 White Orange
GND HDR1 +
J5
EGND
Ground
GND CAN1 Blue
J6 -
TD1 CIM 1 CAN1 White Blue
IOCB (COM1) RD1 +
RESET
to USB port RX
TX Note on Elevator Control Boards RTS
(may require SCKT1
CPB/CB COMMS
Do not set a CIM as global master CTS J1
(COM4)
USB extension that is connected to an elevator
cable) GND
J4 J10 J11
PC with control unit. TD2 J3 J9
Communication RD2
Manager Diag
Global RTS B3 B2 B1 B0 J12
Power
Use 3 loose CTS
485 OUT 485 IN RS-232 wires. Master PC106x 1 2 1 2
Rx-COM CAN
1 2 1 2
COM CAN-Tx J2
Good
Fault
+ TX - + RX - H2 H1
WHT
WHT
GRN
BRN
TD2 J3
RS-232 CTS RD2
Refer to distance Diag J12
RTS B3 B2 B1 B0
chart above. Power
CTS Good
PC106x 1 2 1 2 1 2 1 2
J2
* Insulate shield with PVC tubing such as Alpha Rx-COM CAN COM CAN-Tx Fault
to ACU ground lug
(p/n PVC10516 16 AWG) or comparable insulator.
CONTROL 2
12V
Green
Black
White
Red
J1
1 2 3 4
shield at
(DIP (DIP (DIP (DIP ACU
reader. Relay
Switch 1) Switch 2) Switch 3) Switch 4) Power
H1
+
-
Shield 6 conductors
Blue - optional TAMPER (TB3) red stripe
22 AWG shielded cable SWITCH
(if using pre-alert) TB1 TB2
500 ft (152.4 m) CTS
maximum DTR OCB-8 powered
DCD through ribbon cable LED ON =
RD with J1 set to ACU. RELAY
ENERGIZED
ACU TD K1 K2 K3 K4
enclosure GND
Door # 1
RS-232 (COM4)
Door Strike
- Fail Secure -
to enclosure Shield to N.O.
ground lug +
Black
Blue-optional
Green
Fail Safe to Normally Closed (N.C.) position on OCB-8 relay Fail Secure to Normally Open (N.O.) position on OCB-8 relay