Documente Academic
Documente Profesional
Documente Cultură
Xtreme Circuits
Electronic Projects | Electronic Circuits | Electronic
Search here....
Schematics
HOME ALARM AND SECURITY AUDIO AND MUSIC AUTOMOTIVE HOBBY IR POWER RF RELAY SWITCHE TIMER VIDEO MORE CIRCUITS
Xtreme Circuits
715 suka
A simple NiCd charger can be built using ‘junk box’ components and an inexpensive LM317 or 78xx voltage
regulator. Using a current limiter composed of R3 and a transistor, it can charge as many cells as desired until a
‘fully charged’ voltage determined by the voltage regulator is reached, and it indicates whether it is charging or Sukai Halaman Bagikan
has reached the fully charged state. If the storage capacitor (C1) is omitted, pulsed charging takes place. In this
mode, a higher charging current can be used, with all of the control characteristics remaining the same. The Jadilah orang pertama yang menyukai ini.
operation of the circuit is quite simple. If the cells are not fully charged, a charging current ows freely from the
voltage regulator, although it is limited by resistor R3 and transistor T1.
The limit is set by the formula Imax ≈ (0.6 V) ÷ R3 For Imax = 200 mA, this yields R3 = 3 Ω. The LED is on if current
limiting is active, which also means that the cells are not yet fully charged. The potential on the reference lead of
the voltage regulator is raised by approximately 2.9 V due to the voltage across the LED. This leads to a
requirement for a certain minimum number of cells. For an LM317, the voltage between the reference lead and the
output is 1.25 V, which means at least three cells must be charged (3 × 1.45 V > 2.9 V + 1.25 V). For a 78xx with a
voltage drop of around 3 V (plus 2.9 V), the minimum number is four cells.
Circuit diagram:
When the cells are almost fully charged, the current gradually drops, so the current limiter becomes inactive and
http://xtremecircuits.blogspot.com/2012/10/simple-nicd-battery-charger.html 1/3
25/11/2018 Simple NiCd Battery Charger | Xtreme Circuits
the LED goes out. In this state, the voltage on the reference lead of the regulator depends only on voltage divider
HOME ABOUT CONTACT DISCL AIMER PRIVACY POL ICY
R1/R2. For a 7805 regulator, the value of R2 is selected such that the current through it is 6 mA. Together with the
current through the regulator (around 4 mA), this yields a current of around 10 mA through R1. If the voltage
across R1 is 4 V (9 V – 5 V), this yields a value of 390 Ω. The end-of-charge voltage can thus be set to approximately
8.9 V. As the current through the regulator depends on the device manufacturer and the load, the value of R1 must
be adjusted as necessary. The value of the storage capacitor must be matched to the selected charging current. As
already mentioned, it can also be omitted for pulse charging.
Author: Wolfgang Schmidt - Copyright: Elektor July-August 2004
Click Here!
Find Active Here!
POST A COMMENT
NiCd Battery Charger Fridge-Door Open Alarm Circuit Project Alarm and Security Ampli er Circuits Audio
and Music Automotive Battery and Chargers
Simple NiCd Battery Charger Float Charger For NiMH Cells Booster Circuits Circuit Ideas Clock and Timers
Computer Related Filters and Oscillators Health
Pure Class-A Headphone Ampli er Schematic 18W + 18W Stereo Hi-Fi Audio Ampli er (TDA2030)
and Hobby Home and Garden Home Circuits
Float Charger For NiMH Cells 100W Inverter Circuit Schematic Indicators Infrared Circuits Inverters and
Converters Lighting Circuits Lights and Leds
DS1621 PC Thermometer Circuit Wireless On-O Switch
Microcontrollers Microphone Miscellaneous Motor
NTSC-PAL TV Signal Identi er Pure Class-A Headphone Ampli er Schematic Control Power Circuits Power Supply Pulse and
Frequency Radio RF Relay Sensors and Detectors Speaker and
USB Printer Share Switch Circuit Project Cheap 12V to 220V Inverter Subwoofer Speakers and Subwoofers Switches Telephone and
Intercom Test and Measurement Tone and Preampli er Video
LED Phototherapy Unit Mains Operated LED Circuit Schematic
Vumeters
Compressor For Electret Microphone USB Printer Share Switch Circuit Project
http://xtremecircuits.blogspot.com/2012/10/simple-nicd-battery-charger.html 2/3