Documente Academic
Documente Profesional
Documente Cultură
,Ltd
Professional at Kinds of Mechanical Seals
Features: For plain shafts/ Dual seal/ Unbalanced/ Rotating multiple springs/Independent of direction of rotation;
Advantages
Efficient stock keeping due to easily interchangeable faces,Extended selection of materials;
Operating range
Shaft diameter: d1 = 18 ... 200 mm; Pressure: p1 = 25 bar (363 PSI);
Temperature: t = -50 °C ... 220 °C; Sliding velocity: vg = 20 m/s (66 ft/s);
Axial movement:d1 up to 100 mm: ±0.5 mm,d1 from 100 mm: ±2.0 mm;
Features
For plain shafts
Single seal
Unbalanced
Conical spring rotating
Dependent on direction of rotation
Advantages
Economical seal solution
No damage of the shaft by set screws
Short installation length possible (G16)
Operating range
Shaft diameter: d1 = 6 ... 38 mm (0.25" ... 1.5")
Pressure: p1 = 10 bar (145 PSI)
Temperature: t = -20 °C ... 140 °C (-4 °F ... 355 °F)
Sliding velocity: vg = 15 m/s (50 ft/s)
Axial movement: ±1.0 mm
Operating range
Shaft diameter: d1 = 6 ... 80 mm (0,24" ... 3,15") Pressure: p1 = 10 bar (145 PSI)
Temperature: t = -20 °C ... +140 °C (-4 °F ... +355 °F) Sliding velocity: vg = 15 m/s (50 ft/s)
Axial movement: ±1.0 mm
Design Features: Elastomer bellows rotating;Unbalanced; Independent of direction of rotation; Conical spring;
Pressure: p1 = 12 bar (174 PSI), vacuum up to 0.5 bar (7.25 PSI),
Temperature: t = -20 °C … +140 °C (-4 °F … +284 °F)
Sliding velocity: vg = 10 m/s (33 ft/s)
Axial movement: ±0.5 mm
Design Features:
Single seal ; Loosely inserted seal face provides self-adjusting capability; In-house manufactured sliding parts;
Advantage:
The 560A is self-adjusting to shaft misalignments and deflections because of the loosely inserted seal face as well as
the ability of the bellows to stretch and tighten. The length of the contact area of the bellows with the shaft is an
optimum compromise between ease of assembly (less friction) and sufficient adhesive force for torque transmission.
Additionally the seal fulfills very specific leakage requirements.
Material:
Stationary Ring (Ceramic/SiC/TC)
Rotary Ring (Plastic Carbon/Carbon/SiC/TC)
Secondary Seal (NBR/EPDM/VITON)
Spring & Other Parts (SS304/SS316)
Introduction:
BIA series is more commonly used in mechanical seals, rubber bellows transmit torque, the structure is simple,
compact, short axial dimension, often used in the oil, water and other weak corrosive medium and two
compensation ring may form a double seal.
Application Date:
Specification 18 ~100 mm
Pressure ≤ 1.0 Mpa
Temperature -20 ~ 120 °C
Linear speed ≤ 10 m / s
Axial movement ± 1.0 mm
Materials:
Sealing face: Carbon/Ceramic/SIC/TC
Secondary seal: NBR,EPDM,Viton
Metal components: stainless steel
Carbon/SiC/Viton
Features
Rubber bellows mechanical seal
Unbalanced Single spring
Independent of direction of rotation
Short axial installation length
Advantages
Mechanical seal for large-series cold water pumps. The 301(BT-AR) owes its success to the wide range of application,
the short axial length (this allows for more economic pump construction and saves material). The elasticity of the
bellows design enables a more robust operation.
The 301(BT-AR) can also be used as a multiple seal in tandem or back-to-back arrangement when the product media
cannot ensure lubrication, or when sealing media with a higher solids content. Installation proposals can be provided
upon request.
Features
Single pusher-type seal ,Unbalanced, Conical spring, Dependent on direction of rotation
Advantages
The 155(BT-FN) combines a spring loaded ceramic seal face and the traditional pusher mechanical seals. The seal is
produced with punched metal parts that allow an economical design.
155(BT-FN) mechanical seals are also the ideal solution for light chemicals media applications. To ensure the best
reliable performance, we recommend a material combination of hard material sliding faces and proper elastomer
O-Rings.
Operating range
Shaft diameter: d1*= 10 … 40 mm (0.39" … 1.57")
Pressure: p1*= 12 (16) bar (174 (232) PSI)
Temperature: t* = -35 °C… +180 °C
Sliding velocity: vg = 15 m/s
Features: For Non-stepped shafts, Single seal, Independent of direction of rotation, Encapsulated rotating spring;
Operating range:
Shaft diameter: d1 = 18 ... 100 mm Pressure: p1*) = 0.8 abs.... 25 bar
Temperature: t = -50 °C ... +220 °C Sliding velocity: vg = 20 m/s (66 ft/s)
Axial movement: ±0.5 mm
Advantages: For extreme temperature ranges; No dynamically loaded O-Ring; Self cleaning effect;
Short installation length possible; Pumping screw for highly viscous media available.
Operating range:
Shaft diameter: d1 = 16 … 100 mm Externally pressurized: p1 = … 25 bar (363 PSI)
Internally pressurized: p1 =5 … 10 bar Temperature: t = -40 °C … +220 °C
Stationary seat lock necessary. Sliding velocity: vg = 20 m/s (66 ft/s)
WB2/152 series use PTFE Teflon bellows.It is designed with muti-spring structure.The spring of WB2 type is protected
through a PTFE cover.This mechanical seal is one of the most commonly used seals for corrosion resistant pumps.
Operating range:
Pressure:≤0.5Mpa Temperature:-10~100 ces
Linear Speed:≤15m/s Axial movement:±0.5mm
WB3 型机械密封
Fluids:
Paints and Inks / Water / Weak Acids
The Type 502 mechanical seal is one of the best-performing elastomer bellows seals available. It is suitable for
general service and provides excellent performance in a wide range of hot water and mild chemical duties. It is
specifically designed for confined spaces and limited glands lengths.
Structure characteristics:
Because the rubber bellows, simple structure, compact, also can be made of the radical and axial run-out of the shaft,
Adopting single spring, not easy jam.
Operating Limits:
Specification:0.5 inch-4 inch; Pressure: ≤ 5kg/cm2;
Temperature : -20°C-100°C; Linear speed: ≤10m/s;
John Crane Type 58U / 59U Unbalanced Type Multi Springs Mechanical Seals;
Operating Limits: Temperature: -40°C~+250°C; Pressure: ≤1.2MPa; Speed: ≤15m/s;
Seat Type: BP (For 59U,Material:SiC+PTFE);
BO (For 58U, Material:SiC+VITON)
Materials: Stationary Ring (SiC/TC/Ceramic) ;Rotary Ring (SiC/TC/Carbon) ;
Secondary Seal (VITON/PTFE/PTFE+VITON) ;Spring & Other Parts (SS304/SS316);
Applications: Strong corrosive fluids;
John Crane Type 58B / 59B balanced Type Multi Springs Mechanical Seals;
Operating Limits: Temperature: -40°C~+250°C; Pressure: ≤1.2MPa; Speed: ≤15m/s;
Seat Type: BP (For 59B,Material:SiC+PTFE);
BO (For 58B, Material:SiC+VITON);
Materials: Stationary Ring (SiC/TC/Ceramic) ;Rotary Ring (SiC/TC/Carbon) ;
Secondary Seal (VITON/PTFE/PTFE+VITON) ;Spring & Other Parts (SS304/SS316);
Applications: Strong corrosive fluids;
FBD series mechanical seal is uneasy to be blocked due to its single spring structure. It has advanced rotating ring
float ability so that reduced compensational resistance. It’s suitable for oil, water and other weak corrosive medium.
Operating limits:
Pressure: 0-1.2Mpa; Linear Speed: ≦10m/s; Temperature: -40°C~+250°C; Axial Movement:±1.0mm;
Materials:
Rotary ring: SUS304 (316) /Carbon /SIC /TC; Stationary ring: Carbon /SIC /TC/CE;
Secondary seal: NBR /EPDM /VITON /PTFE; Spring : S.S /SUS304 /SUS316;
Features:
Dual seal; Good chemical resistance and ability to handle solids; In-house manufactured sliding parts;
Advantages:
The ED560 is a dual seal in a back-to-back arrangement with an EA560 base. Therefore,it combines the advantages
of the EA560 with the advantages of a dual seal.
Operating range:
Shaft diameter: d1 = 13 ... 50 mm
Pressure: p1=2 bar ... 3 bar
vacuum ... 0.1 bar (1.45 PSI)
Temperature: t = -20 °C ... +70 °C
Sliding velocity: vg = 5 m/s (16 ft/s)
Features
Drive with clasp spring
Dependent on direction of rotation
Interchange with Wilo pump seals
Operating range
Shaft diameter: d1*= 8 … 50 mm
Pressure: P≤ 0.4 MPa
Temperature: t* = -20 °C… +200 °C
Sliding velocity: vg = 10 m/s
202U 型机械密封
202U Series Mechanical Seals
224U 型机械密封
224U Series Mechanical Seals
606 型机械密封
606 Series Mechanical Seals