Ail 160 - 0s (2014)
TABLE 1 Mechanical Properios
(Condon and Diameter or Distance
Betwoon Paral Suracs. nn)
Tense Stenge, min,
(Pa)
Void Stengh (02% ose, Bongation nm or 50
‘in pal (Pa) ‘mm oF 40. min
idol (UNS nO2209
Cai-waied as wary
Rounes, 1 (25.4) and under 180000 (650) 0.000 415) 10°
eunds ovr 110 (254 to 101.6) nck. 75.000 (515) 50 000 (345) 5
Sauares, hexagons, snd rectangles, al sizes 15 000 (450) 0 000 (275) 2°
Hote
‘Al soctone, a sizes 60.000 (415) 15.00 (105) oe
Flings and ks” ass = =
Anca
"Rods and bas, al siros 55 000 (280) 15.000 (105) oo
Range and dks = E =
Forage iq x 2
= —Loi Gabon Niel (ONS NOSU7) and Solaion Srengihened Nika UNS WOGETiy
Hetero
50 00 (345) 10.000 (70) 40°
‘A educa sizes 50 000 (345) 10.000 70) 40
500 123,
{Not epplicabl to clametrs or cose sections under sin. (24 mm)
2 Maraness B45 o 8, or equiva.
Hardness B45 1 970 or equaen
(7.9 mm) and under i hikes te longaon shel be 25%, min.
Foran quai rised to chanical requirement and sue nspecion on No ns properties ar requed
Chemie
S.A The material shall conform to the composition limits
specified in Table 2
5.2 If @ product (check) analysis is performed by the
purchaser, the material shall be done per Specification BS80
and the material shall conform to the product (check) analysis
variations defined in Check Analysis Variation table of Speci
fication BS80,
1 Comp
6. Mechanical and Other Requirements
6.1 Mechanical Properties—The material shall conform to
the mechanical properties specified in Table 1
7. Dimensions and Permissible Variations
7.1 Diameter, Thickness, or Width—The permissible varia
tions from the specified dimensions as measured on the
diameter or between parallel surfaces of cold-worked rod and
bar shall be as prescribed in Table 3, and of hot-worked rod and
bar as prescribed in Table 4
‘TABLE 2 Chemical Requirements
‘Compostion Umit %
San
Beret sans feet gS,
ony” Neal ONS heaters
ran
a = ae
fone ete
oo oe ee
Minin, mae 05 Bea Sg
cone ti i ae
Sten ne ee
Eons i ois
“Element shal be detemined artrneicaly by aifrence
# Carbon max vale for UNS NO2200 was corected edo.
| Carbon max value for UNS NO2211 was conected extoray,
Copyright by ASTM Int (ll sighs reserved
Licensed trite by
‘TABLE 3 Permissible Variations in Diameter or Distance Between
Parallel Surfaces of Cold-Worked Rod and Bar
Permissible Vanaton fore
Specied Dmension,in.(mmy* __Speced Dimension fe)
ao iS cae See a
“hu (6) 10 e (4.8), excl ° 0.0 (0.05)
Ye (48) 0 '6(12.7), exe ° 0.008 (0.08)
Ye (1227) to e298), cl 0.001 (0.08) 0.002 (0.05)
vere (238 019 (49.2, ft 2.0015 (004) 0.002 (0.08)
‘Over tie (9.2) to 28 (635), na 0.002005) 0.008 (210)
rer 214 (685) 0 (76.2) ned 0.085 (0.06) 9.08 (013)
Over 9 (76.2) 1 3 (88.9), nc 0.008 (0.08)
0.006 (0.15)
Over 315 (689) 10 4 (103.9 ed 0.0095 (000) _ 0.007 (0.18
esagons, squares, rectangles
Ye(t27) ad lees ° 0.004 (010)
Over 38 (127) 1 4 (222), nt ° (0.005 (0.13)
vor (222) 0 114 (81.8), Inet 5 2.007 (0:8),
(Over 14 (81.8) fo 204 (57.2), nd ° 2.009 (0.23)
Over 21 (67.2) 6 3 762 ne, ° 2011 (028)
Over 3 (76.2) 103 (8.9), incl ° 0.015 (0.38)
Over 394 (889) 16 4 (101.8), tc ° 0.017 (048),
‘Dimensions apply to Gaeta of ourds to dtanca between paral sutoces 1
'nexagons and squares, and separately 16 width and theknese of testang,
7.2. Out-of- Round—Hot-worked rods and cold-worked rods
(except “forging quality”), all sizes, in straight lengths, shall
‘not be out-of-round by more than one half the total permissible
variations in diameter shown in Tables 3 and 4, except for
hhot-worked rods in. (12.7 mm) in diameter and under, which
may be out-of-round by the total permissible variations in
diameter shown in Table 4.
7.3 Corners—Cold-worked bars will have
angles and sharp corners,
7.4 Machining Allowances for Hot-Worked Materials —
‘When the surfaces of hot-worked products are to be machined,
the allowances. prescribed in Table 5 are recommended for
normal machining operations.
practically exact
‘ire Bafta Ter Enginering Services pursuant o License Agreement. No farther reproduction authorized