Documente Academic
Documente Profesional
Documente Cultură
BU Moulding compound b
Bakelite 151733 typical
Reviewed on: 05.05.2004
Storage capability:
2 years
(relative humidity of 50 - 60 % and maximum storage temperature 20°C)
Product description:
Phenolic moulding compound, mainly organically filled, standard moulding compound for normal stress.
Application areas:
Contact strip.
This data sheet is valid until 05.05.2005. Should this material be purchased after the validity date stated, please request an
up-to-date data sheet. Page 1 of 2
All information, recommendations and suggestions provided by Bakelite AG in the form of verbal or written communication, or in pertinent data bases, represent our best knowledge and experience. Such data are Gennaer Straße 2-4
non-binding in character, and do not represent, either explicity or implicitly, assurance or a guarantee of specific properties. The specified parameters merely represent typical data; they do not form a basis for D-58642 Iserlohn-Letmath
either a guarantee or a specification. The information, recommendations and suggestions we provide describe our products and possible applications in general or exemplary terms; they do not relate to specific
cases. The process of constant continued development and improvement of our products canlead to changes in pertinent parameters, texts and illustrations; no special mention is made of possible alterations. Our
technical advise does not free the customer of ist responsibility to verify our current information, in particular our our technical data sheets, safety data sheets and technical information leaflets. The customer will
Postfach 7154
conduct ist own tests of our products to determine their suitability for the intended processes and uses, as well as to establish that their processing properties are appropriate in the pertinent situation, since our D-58609 Iserlohn
products may be used in a wide range of tchnical applications that involve very diffrent requirements according to the specific situation. Therefore, such specific cases are outside our control, and are the exclusive
resaponsibility of the customer. A pertinent agreement is necessary in case a binding assurance of specific parameters required. Customers and users of our products must themselves observe possible patent Tel. (+49) 02374-925-0
rights, existing legislation and regulations. This publication does not represent a license, or does ti authorize infringement of any type of patent. Note:This version supersedes and replaces all previous publications on
this subject Fax (+49) 02374-925-506
Bakelite ® is a registrated trademark of Bakelite AG in Europe. Rütaphen ® is a registrated trrademark of Bakelite AG in the United States and Canada. Internet: www.bakelite.de
E-Mail: info@bakelite.de
Technical Information
BU Moulding compound b
Moulding conditions: Bakelite 151733 Reviewed on: 05.05.200
Injection molding Compression molding
Temperature of material 80 - 100 °C Mould temperature 160 - 190 °C
Mould temperature 160 - 190 °C Curing time (per mm of wall thickness) 20 - 40 s
Curing time (per mm of wall thickness) 10 - 20 s Cavity moulding pressure >15 MPa
Barrel temperature - Feed zone 60 - 75 °C
Barrel temperature - Nozzle zone 80 - 100 °C
Cavity moulding pressure >15 MPa
Back pressure 0,5 - 2 MPa
Holding pressure ca. 60% of injection pressure
All information, recommendations and suggestions provided by Bakelite AG in the form of verbal or written communication, or in pertinent data bases, represent our best knowledge and experience. Such data are Gennaer Straße 2-4
non-binding in character, and do not represent, either explicity or implicitly, assurance or a guarantee of specific properties. The specified parameters merely represent typical data; they do not form a basis for D-58642 Iserlohn-Letmath
either a guarantee or a specification. The information, recommendations and suggestions we provide describe our products and possible applications in general or exemplary terms; they do not relate to specific
cases. The process of constant continued development and improvement of our products canlead to changes in pertinent parameters, texts and illustrations; no special mention is made of possible alterations. Our
technical advise does not free the customer of ist responsibility to verify our current information, in particular our our technical data sheets, safety data sheets and technical information leaflets. The customer will
Postfach 7154
conduct ist own tests of our products to determine their suitability for the intended processes and uses, as well as to establish that their processing properties are appropriate in the pertinent situation, since our D-58609 Iserlohn
products may be used in a wide range of tchnical applications that involve very diffrent requirements according to the specific situation. Therefore, such specific cases are outside our control, and are the exclusive
resaponsibility of the customer. A pertinent agreement is necessary in case a binding assurance of specific parameters required. Customers and users of our products must themselves observe possible patent Tel. (+49) 02374-925-0
rights, existing legislation and regulations. This publication does not represent a license, or does ti authorize infringement of any type of patent. Note:This version supersedes and replaces all previous publications on
this subject Fax (+49) 02374-925-506
Bakelite ® is a registrated trademark of Bakelite AG in Europe. Rütaphen ® is a registrated trrademark of Bakelite AG in the United States and Canada. Internet: www.bakelite.de
E-Mail: info@bakelite.de