Documente Academic
Documente Profesional
Documente Cultură
Description Features
The BP3125 is a high precision primary-side feedback Built-in 600V Power MOSFET
and regulation controller for LED lighting, it operates Constant current control without secondary sense
in constant current control mode and is designed to and feedback circuit.
work in inductor current discontinuous conduction ±3% LED current accuracy
Ultra low operating current to improve efficiency
mode and extremely suitable for flyback convertor
High resistance feedback resistor to improve
under universal input, the output power of system
efficiency
should be less than 12W. Universal input voltage
LED short and open circuit protection
The BP3125 integrates 600V power MOSFET. Since
VCC under-voltage protection
adopting primary sense and feedback control
Feedback loop short circuit protection
technology, the secondary sense and feedback circuit
Current sense resistor open circuit protection
is eliminated. The loop compensation components are Over temperature protection
also removed while maintaining stability overall No external loop compensation component
operating conditions. The low component counts and required
low BOM cost are realized. Available in DIP-8 package
Typical Application
NP NS
NAUX
AC BP3125
FB NC
VCC NC
CS DRAIN
GND DRAIN
BP3125_EN_DS_Rev.1.0 www.bpsemi.com 1
Bright Power Semiconductor Co. Confidential – Customer Use Only
BP3125
High Precision PSR Constant Current LED Driver
Ordering Information
Part Number Package Operating Package Method Marking
Temperature
Tube BP3125
BP3125 DIP8 -40℃ to 105℃ XXXXXY
50 Piece/Tube WWXYY
GND NC
XXXXXY: lot code
XXXXXY
BP3125
WWXYY
FB NC WW: Sign
X: Year
VCC DRAIN
YY:Week
CS DRAIN
Pin Definition
Pin No. Name Description
1 GND Ground
Feedback. This pin detects the output information from auxiliary
2 FB
winding.
3 VCC Power supply
Current sense. This pin connects a current sense resistor to GND to detect
4 CS
the primary current of transformer.
5,6 DRAIN Internal high voltage MOSFET drain.
BP3125_EN_DS_Rev.1.0 www.bpsemi.com 2
Bright Power Semiconductor Co. Confidential – Customer Use Only
BP3125
High Precision PSR Constant Current LED Driver
ESD (note3) 2 KV
Note 1: Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. Under “recommended operating
conditions” the device operation is assured, but some particular parameter may not be achieved. The electrical characteristics table defines the operation
range of the device, the electrical characteristics is assured on DC and AC voltage by test program. For the parameters without minimum and maximum
value in the EC table, the typical value defines the operation range, the accuracy is not guaranteed by spec.
Note 2: The maximum power dissipation decrease if temperature rise, it is decided by TJMAX, θJA, and environment temperature (TA). The maximum power
dissipation is the lower one between PDMAX = (TJMAX - TA)/ θJA and the number listed in the maximum table.
BP3125_EN_DS_Rev.1.0 www.bpsemi.com 3
Bright Power Semiconductor Co. Confidential – Customer Use Only
BP3125
High Precision PSR Constant Current LED Driver
Feedback Section
BP3125_EN_DS_Rev.1.0 www.bpsemi.com 4
Bright Power Semiconductor Co. Confidential – Customer Use Only
BP3125
High Precision PSR Constant Current LED Driver
Symbol Parameter Conditions Min. Typ. Max. Units
MOSFET Section
Static drain-source
RDS_ON VGS=10V/IDS=0.5A 6 Ω
on-resistance
Drain-source breakdown
BVDSS VGS=0V/IDS=250uA 600 V
voltage
Drain-source leakage
IDSS VGS=0V/VDS=600V 1 uA
current
Note 4 : production testing of the chip is performed at 25°C.
Note 5: the maximum and minimum parameters specified are guaranteed by test, the typical value are guaranteed by design, characterization and statistical
analysis
BP3125_EN_DS_Rev.1.0 www.bpsemi.com 5
Bright Power Semiconductor Co. Confidential – Customer Use Only
BP3125
High Precision PSR Constant Current LED Driver
BP3125_EN_DS_Rev.1.0 www.bpsemi.com 6
Bright Power Semiconductor Co. Confidential – Customer Use Only
BP3125
High Precision PSR Constant Current LED Driver
VCC FB DRAIN
FB SCP
6.5V 14V
OVP FB Sense
+
-
-
UVLO OTP
MOSFET
Reset CC & Logic Gate
Control Driver
LEB
Current Sense CS
+
-
500mV
GND
The BP3125 is a high performance power switch Cycle-by-Cycle current sense is offered in BP3125,
specially designed for LED lighting, it uses the the CS is connected to the current sense comparator,
patent constant current control technology of BPS. and the voltage on CS will be compared with the
The BP3125 integrates a 600V power MOSFET. The internal 500mV reference voltage, the MOSFET will
accurate LED current can be realized without be switched off when the voltage on CS reaches the
opto-coupler and TL431 feedback circuit while threshold. The output of the comparator also includes
minimizing the external component count, lowering a 500nS leading edge blanking time
the total bill of material cost. The primary peak current is given by:
Start Up 500
I P_PK (mA)
The start-up current in BP3125 is designed to as low RCS
as 25uA. The VCC capacitor will be charged through
The current in LED can be calculated by the
the start-up resistor when the system is powered on,
equation:
once the voltage on VCC reaches the start-up
threshold, the BP3125 will start to operate, and then
the VCC is supplied by the auxiliary winding.
BP3125_EN_DS_Rev.1.0 www.bpsemi.com 7
Bright Power Semiconductor Co. Confidential – Customer Use Only
BP3125
High Precision PSR Constant Current LED Driver
Protection Function
I P_PK
N
I OUT P The BP3125 has several protection functions. The
4 NS
internal MOSFET will be shut down immediately
Where, when the voltage on VCC reaches the threshold of
NP: primary winding turns of transformer OVP and the device will not recover until the
NS: secondary winding turns of transformer protection condition is removed. A 19V zener diode
IP_PK: peak current in MOSFET is designed in the BP3125 to prevent the chip
Feedback Network damage from the abnormal situation.
The BP3125 senses the output information through The thermal shutdown circuitry in the BP3125
the feedback network and the FB threshold voltage is senses the die temperature after start up, and the
set to 1V. The ratio of FB upper resistor to lower thermal protection threshold is set to 150℃ with a
resistor is recommended to about 4.0. The FB upper 20℃ hysteresis. When the temperature on die of
resistor can be set to 300KΩ~750KΩ to improve BP3125 rises and reaches the threshold, the power
efficiency of convertor. MOSFET will be shut down immediately and
maintained switch off until the temperature on die
The upper resistor on FB is also used for line
falls 20 ℃ from thermal protection trigger point.
compensation.
The system will work in low consumption mode
The ratio of line compensation can be calculated by
when the output LED short circuit or open circuit is
the equation:
detected, while the BP3125 continuous to detect
V AUX
VCS 1.1 10 6 mV output status until the LED recover to normal
RFBH condition, and then the device will be operate in
Where, RFBH is the upper resistor of the feedback normal mode.
network.
PCB Layout
Operation Switching Frequency
The following rules should be followed in BP3125
The BP3125 is designed to work in discontinuous PCB layout:
conduction mode and no external loop compensation
Bypass Capacitor
component is required while maintaining stability.
The maximum duty cycle is limited to 42%. The The bypass capacitor on VCC should be as close as
maximum switching frequency should be set to less possible to the VCC pin
than 100KHz and the minimum switching frequency Ground Path
should be set to more than 20KHz. The maximum
The power ground path for current sense should be
and minimum switching frequency is limited in
short, and the power ground path should be separated
BP3125 to ensure the stability of system.
from small signal ground path before the negative of
The switching frequency can be set by the formula: the bulk capacitor.
BP3125_EN_DS_Rev.1.0 www.bpsemi.com 8
Bright Power Semiconductor Co. Confidential – Customer Use Only
BP3125
High Precision PSR Constant Current LED Driver
NC Pin
Drain pin
FB Pin
BP3125_EN_DS_Rev.1.0 www.bpsemi.com 9
Bright Power Semiconductor Co. Confidential – Customer Use Only
BP3125
High Precision PSR Constant Current LED Driver
Physical Dimensions
BP3125_EN_DS_Rev.1.0 www.bpsemi.com 10
Bright Power Semiconductor Co. Confidential – Customer Use Only