Documente Academic
Documente Profesional
Documente Cultură
The synoptic below represents the Crystal supervisor equipped with all the available options. These
options are integrated to the supervisor in function of technical data specified at the order.
LED
8 leds indicators
(Option)
UIF Mains
measurement
(Option)
CRL
Supervisor
CRYSTAL
9 Display
- Mains measurements :
- Voltages, Currents, Frequency MAINS
If UIF Option, see « Mains measurements » chapter for more information. L1 400V 1.0A 50Hz
L2 400V 1.0A
L3 400V 1.0A
Note: A specific page can be displayed for a while. Use the and keys to select the desired
page. This displayed page will maintained approximately 30 seconds then will come back to the sequential display. The sequential display
RESET
ESC
also comes back after pressing the key.
Displaying of an event
When an event occurs, a page is inserted into the display sequence. The page EVENT
describes the event and date (DD/MM/YYYY) and time (HH:MM:SS) of occurrence. No mains
When the event disappears, the page is deleted from the display sequence. 27/03/2011 13:35:23
- Memorized fault : The page is maintained till the fault is acknowledged. For FAULT
RESET End of discharge
resetting the fault, press the ESC
key.
27/03/2011 14:53:42
Note : When a fault is displayed, the other pages can be switched by pressing the or keys.
The sequential display of pages will take again automatically after 30 seconds.
Use the and keys to view events, alarms and faults. The most recent
event, alarm or fault is <001>. HISTORY
<001> Beginning
End of discharge
27/03/2011 14:53:42
The pressure on the key allows to display the older events, alarms or fault
(maximum up to 100).
RESET
Press the ESC
key to return to the sequential display.
The settings and commands below can be accessed without a password from the display screen.
Use the and keys to go to the required screen.
Use the and keys to select the required value.
SET
Press the ENTER key to validate your choice.
RESET
Press the ESC key to return to the sequential display.
LANGUAGE
<English>
Choice of language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Confirm : ENTER
DATE YYYY/MM/DD
<27/03/2008>
Setting of the date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Confirm : ENTER
HOUR HH:MM
<13:30>
Setting of the time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Confirm : ENTER
BACKLIGHT
Setting of backlight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <3>
Confirm : ENTER
CHARGER
<OFF>
Charger ON/OFF command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Confirm : ENTER
BOOST
<ON>
Boost command* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Confirm : ENTER
LED TEST
<ON>
LED test command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Confirm : ENTER
Confirm : ENTER
BATTERY TEST
Battery test command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <ON>
* See « Advanced function » chapter Confirm : ENTER
Use the and keys to go to the "RESTRICTED ACCESS" screen. RESTRICTED ACCESS
SET
ENTER
Press the key to enter the menu. Confirm : ENTER
The flashing of 3 leds (green, yellow, red) indicates the restricted access mode.
The tree structure below gives the list of commands and settings available depending on the options and
system configuration.