Documente Academic
Documente Profesional
Documente Cultură
Weatherproof Camera
User Manual SCO-2370
safety information
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
● SAFETY INFORMATION
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol indicates that there are important operating and maintenance
instructions in the literature accompanying this unit.
English_3
safety information
7. Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fire or FCC Statement
electric shock. This device complies with part 15 of the FCC Rules. Operation is subject to the following
8. If any unusual smells or smoke come from the unit, stop using the product. In such case, two conditions :
immediately disconnect the power source and contact the service center. Continued use in 1) This device may not cause harmful interference, and
such a condition may cause fire or electric shock. 2) This device must accept any interference received including interference that may
● SAFETY INFORMATION
9. If this product fails to operate normally, contact the nearest service center. Never cause undesired operation.
disassemble or modify this product in any way. (SAMSUNG is not liable for problems CAUTION
caused by unauthorized modifications or attempted repair.) This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of FCC Rules. These limits are designed to provide
10. When cleaning, do not spray water directly onto parts of the product. Doing so may
reasonable protection against harmful interference when the equipment is operated in
cause fire or electric shock.
a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not
CAUTION installed and used in accordance with the instruction manual, may cause harmful
1. Do not drop objects on the product or apply strong blows to it. Keep away from a location interference to radio communications. Operation of this equipment in a residential area
subject to excessive vibration or magnetic interference. is likely to cause harmful interference in which case the user will be required to correct
the interference at his own expense.
2. Do not install in a location subject to high temperature (over 50°C), low temperature (below
-50°F), or high humidity. Doing so may cause fire or electric shock.
IC Compliance Notice
3. If you want to relocate the already installed product, be sure to turn off the power and then
move or reinstall it. This Class A digital apparatus meets all requirements of the Canadian
Interference.-Causing Equipment Regulations of ICES-003.
4. Remove the power plug from the outlet when there is a lighting storm. Neglecting to do so
may cause fire or damage to the product. Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
5. Keep out of direct sunlight and heat radiation sources. It may cause fire.
This marking on the product, accessories or literature indicates that the product and its electronic accessories
(e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their
6. Install it in a place with good ventilation. working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal,
please separate these items from other types of waste and recycle them responsibly to promote the sustainable
7. Avoid aiming the camera directly towards extremely bright objects such as sun, as this reuse of material resources.
may damage the CCD image sensor. Household users should contact either the retailer where they purchased this product, or their local government
office, for details of where and how they can take these items for environmentally safe recycling.
8. Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids,
Business users should contact their supplier and check the terms and conditions of the purchase contract.
such as vases, shall be placed on the apparatus. This product and its electronic accessories should not be mixed with other commercial wastes for disposal.
9. The Mains plug is used as a disconnect device and shall stay readily operable at any
Correct disposal of batteries in this product
time.
(Applicable in the European Union and other European countries with separate battery return systems.)
This marking on the battery, manual or packaging indicates that the batteries in this product should not be
disposed of with other household waste at the end of their working life. Where marked, the chemical symbols
Hg, Cd or Pb indicate that the battery contains mercury, cadmium or lead above the reference levels in EC
Directive 2006/66. If batteries are not properly disposed of, these substances can cause harm to human health
or the environment.
To protect natural resources and to promote material reuse, please separate batteries from other types of waste
and recycle them through your local, free battery return system.
● CONTENTS
5. Clean only with dry cloth.
6. Do not block any ventilation openings. Install in accordance with the manufacturer’s INSTALLATION & CONNECTION 13 Connecting to Monitor
instructions. 14 Connecting to Power
7. Do not install near any heat sources such as radiators, heat registers, or other apparatus
(including amplifiers) that produce heat.
8. Do not defeat the safety purpose of the polarized or grounding-type plug.
13 15
16
RS-485 Communication control
Using Coaxial Communications
A polarized plug has two blades with one wider than the other. A grounding type plug has
two blades and a third grounding prong. The wide blade or the third prong is provided SETUP 17 Menu Configuration
for your safety. If the provided plug does not fit into your outlet, consult an electrician for 18 Menu Setup
replacement of the obsolete outlet.
9. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
17
10. Only use attachments/accessories specified by the manufacturer. TROUBLESHOOTING 38 Troubleshooting
38
11. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or
sold with the apparatus. When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
12. Unplug this apparatus during lightning storms or when unused for long
periods of time. When a cart is used, use caution when moving the 39 Specifications
cart/apparatus combination to avoid injury from tip-over.
SPECIFICATIONS
41 Dimension
13. Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as powersupply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus
39
has been exposed to rain or moisture, does not operate normally, or has been dropped.
42
6_ important safety instructions English_7
introduction
FEATURES WHAT’S INCLUDED
y 37x Optical Zoom Check if the following items are included in the product package.
The built-in SCO-2370 optical zoom lens is a highly durable component. It features auto
focus, auto iris, and zoom functions.
● INTRODUCTION
y High Resolution ڪڞڮ
ڎڍڈ
ڋڒ
By adopting a diagonal 1/4” 410,000 (NTSC) pixel, 470,000(PAL) pixel SONY CCD, the
camera produces clear picture quality with a horizontal resolution of 600TV lines for color
and a horizontal resolution of 700TV lines for BW mode.
y SSNR3 (Samsung Super Noise Reduction) Function L-type hexagon wrenches
SCO-2370 Sunshield
The high-performance W-V DSP chip effectively removes low-light gain noise and (4.0mm)
ghosting to provide clear images even in dark environments.
High Resolution 37x
This camera has a function that automatically selects the mode that is appropriate for
daytime or night-time conditions.
The COLOR mode operates in daytime conditions to provide optimum colors, and BW
mode operates in night-time conditions to enhance the definition of the image.
y IP68 Approved/Dust and Rain Resistant
With dust and rain resistant design, the camera can be installed outside under building Sunshield Adaptor (1EA) Tapping Screw (3EA) User Guide
eaves or places that are exposed to the dust and rain.
y SSDR (Samsung Super Dynamic Range)
For images with high contrast between bright and dark Areas from difficult lighting
conditions such as backlighting, this camera selectively illuminates darker Areas while
retaining the same light level for brighter Areas to even out the overall brightness.
y Communication
RS-485, Coaxial communication methods are supported. Installation Video Output Cable
- RS-485 Communications : SAMSUNG-T, SAMSUNG-E, Pelco-P, Pelco-D, Vicon,
Panasonic, Bosch, Honeywell, AD
- Coaxial Communications : Pelco Coaxitron
y Temperature control
The built-in heater & fan enables normal operation under a severe condition of -50°C.
y OSD
The camera’s OSD is complimented by 18 foreign languages.
- NTSC : Korean, English, French, Spanish, Japanese, Portuguese, Taiwanese
- PAL : English, French, German, Spanish, Italian, Chinese, Russian, Czech, Polish,
Portuguese, Romanian, Serbian, Swedish, Danish, Turkish
8_ introduction English_9
introduction
COMPONENT NAMES AND FUNCTIONS
Front Back
● INTRODUCTION
❶ ➋ ➌
➍
ڋڒ
ڎڍ
ڈڪ
➎
ڞڮ
❶
➊ Camera Sunshield
➋ Sunshield adaptor : Fixing the sunshield onto the camera.
➌ Lens
➋
➍ Video Output Terminal to Monitor : Used for monitoring of video output When ➌
camera installation. ➍
➎ Function Setup Switch : Display the menu on the screen and move the cursor
to four directions to confirm status or after changing a ➊ Power input terminal : Connect the power as specified for each model here.
selected item. ➋ MD Output Terminal : Motion detection signals are output through this terminal.
➏ Front cover ➌ RS-485 control terminal : You can control SETUP MENU through this port by using
external controllers like a Remote controller that RS-485
Communication is supported. For details, see page 15.
➍ Video output terminal : Video signals are output through this port. Connect this port
to the Video IN port of a monitor.
This product is equipped with a built-in heater & fan that helps maintaining operational
temperature and humidity.
CCD Camera
Front cover
Heater y The connection method varies depending on the type of monitor and accessories.Please
refer to the user’s manual for each instrument.
y Please turn off the power when connecting.
1. While powered, the heater & fan operates according to the camera’s internal temperature.
Check heater & fan operation with given internal temperature by referring to the below:
y While the camera is powered, the heater & fan operates if its internal temperature drops
below -10 °C. When the camera’s internal temperature reaches -5 °C, the heater & fan
stops operating.
y While the camera is powered and its internal temperature is between -50 °C ~ -15 °C,
the message “Low Temperature Wait” appears. When it reaches -15 °C, the camera is
initialized and video begins output.
y When the camera’s internal temperature reaches 40 °C, the fan starts operating.
If the camera’s internal temperature reaches 80 °C, it will be initialized.
Be careful not to touch the heater while installing if the ambient temperature is below than -10°C,
M since the heater may operate immediately after applying the power.
If the front cover is cross threaded or not correctly tightened the camera housing will not be weatherproof.
When you combine the front cover, combine the triangle of front cover and triangle of main body
confront each other.
WHITE RS-485+
BLUE RS-485-
Using RS-485 communication will enable you to control the OSD menu from a
SAMSUNG TECHWIN System Controller or DVR.
(1) Connection to a PC.
Connect the camera to the PC via a RS-485 converter using RS-485 and a serial cable.
EX) SERIAL PORT OF THE PC(COM1) p SERIAL CABLE p RS-485 CONVERTER
---- Power Input Terminal
p RS-485 CONTROL CABLE
(2) Connection to a DVR or System Controller.
Connect the RS-485 cable to the connection ports of the DVR or System Controller.
When the resistance value of copper wire is at [20°C(68°F)] 485 Control Board Connection Port RS-485 Control Port
Copper wire size(AWG) #24(0.22mm²) #22(0.33mm ) 2
#20(0.52mm )2
#18(0.83mm )
2
y As shown in the table above, voltage decreases as the wire gets longer. * RS-485 Communication establishment initial value
Therefore having an excessively long distance between the power adaptor and the
camera may affect the camera’s performance. Item Camera ID BAUD RATE UART MODE RET PKT
 Standard voltage for camera operation : DC 12V±10% / AC 24V±10% Initial value 1 9600 8-NONE-1 DISABLE
 There may be some deviation in voltage drop depending on the type of wire and the
manufacturer.
When making a control system to control the camera, please use to the protocol(SAMSUNG-T,
M SAMSUNG-E, PELCO-P, PELCO-D, VICON, PANASONIC, BOSCH, HONEYELL,AD).
Please use a power adaptor that meets the required standards.
M Please connect the power after installation.
When you connecting to RS-485 CONTROL TERMINAL, please peel off the outer skin inside the
RS-485 CONTROL TERMINAL.
● SETUP
CAMERA DVR CONTROLLER
RIGHT RIGHT KEY JOYSTICK RIGHT ● MODE ● ZOOM TRACK ● ZOOM SPEED
ڪڞڮ
ڎڍڈ
ڋڒ
Recommended Cable
Distance
Specification
300m 3C2V(RG-59/U)
450m 5C2V(RG-6/U)
600m 7C2V(RG-11/U)
If the camera is controlled through coaxial communication, please use a video amp intended for
M coaxial communications. Regular video amps do not transfer coaxial signals.
16_ installation & connection English_17
setup
MENU SETUP SSDR (Samsung Super Dynamic Range)
SSDR illuminates darker spots of an image while retaining the same light level for brighter
Use the Function Setup switch within the camera.
spots to even out the overall brightness of images with high contrast between bright and
dark spots.
● SETUP
1. When the SETUP menu screen is displayed, MAIN SETUP
select ‘SSDR’ by using the Function Setup
䯝 SSDR ON
switch so that the arrow indicates ‘SSDR’. WHITE BAL ATW
Function Setup switch
2. Use the switch to change the SSDR level BACKLIGHT OFF
according to the contrast between bright and MOTION DET OFF
dark areas. FOCUS
EXPOSURE
SPECIAL
1. Press the Function Setup switch for 2 seconds. (Short-pressing the Function Setup RESET
Switch activates the AUTO FOCUS). EXIT
y Main setup menu is displayed on the monitor screen.
MAIN SETUP
Select the function 君SSDR ON Change the status
using the Function using the Function
Setup switch.
WHITE BAL ATW Setup switch.
BACKLIGHT OFF
MOTION DET OFF
FOCUS SSDR ON SSDR OFF
EXPOSURE
SPECIAL
RESET
White Balance (WHITE BAL)
EXIT
Use the White Balance function to adjust the screen color.
2. Select the desired feature using the Function Setup switch. 1. When the SETUP menu screen is displayed,
MAIN SETUP
y Each pressing of the Function Setup switch moves the indicator to the next or select ‘WHITE BAL’ by using the Function
SSDR ON
Setup switch so that the arrow indicates
previous feature. 䯝 WHITE BAL ATW
‘WHITE BAL’.
y Move the arrow indicator to the desired feature item. BACKLIGHT OFF
2. Select a desired mode using the Function MOTION DET OFF
3. Change the status of the selected feature using the Function Setup switch. Setup switch. FOCUS
4. When completed, move the arrow indicator to ‘EXIT’ and press the Function Setup EXPOSURE
switch. SPECIAL
RESET
Features marked with a have an accessible submenu.
M An item with the - - - icon is unavailable due to function settings.
EXIT
● SETUP
Setup switch.
the area more clearly. TOP IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII 30
- AWCSET : To find the optimal luminance level for the current environment,
point the camera towards a sheet of white paper and press the y HLC (HIGH LIGHT COMPENSATION) : BOTTOM IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII 75
Function Setup switch. If the environment changes, readjust it. If the scene contains extremely bright light LEFT IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII 30
- OUTDOOR : Select this when the color temperature is between 1,700˚K and areas such as; from car headlight, the
RIGHT IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII 70
11,000˚K. (sodium light inclusion) light can mask out much of the on-screen RETURN
detail.
- INDOOR : Select this when the color temperature is between 4,500˚K and 8,500˚K.
- LEVEL : Adjust level of the HLC function.
(LOW,MIDDLE,HIGH)
M White Balance may not work properly under the following conditions. In this case select the AWC
mode. - MASK TONE : Change the brightness
➊ When the color temperature of the environment surrounding the subject is out of the control
range (e.g. clear sky or sunset). 3. Select a desired mode using the Function Setup switch and press the Function Setup
switch.
➋ When the ambient illumination of the subject is dim.
➌ If the camera is directed towards a fluorescent light or is installed in a place where y Select ‘BLC’ to adjust the area to be enhanced then adjust the level.
illumination changes dramatically, the White Balance operation may become unstable.
M Since the following symptoms may occur according to the ambient illumination when BLC is
selected, set it to OFF.
BACKLIGHT ➊ Color or screen changes unnaturally.
➋ Noise appears in the bright part of the screen.
Unlike conventional cameras, the SCO-2370 is designed to deliver a distinctive subject
and background at the same time, even when the subject is backlight, by using the Since the performance of the BLC function may be affected by the area of the bright part of the
features of the proprietary W-V DSP chip. screen, optimize the installation angle for the best BLC performance.
If you increase LIMIT, the screen display may be distorted.
1. When the SETUP menu screen is displayed,
select ‘BACKLIGHT’ by using the Function
MAIN SETUP
For high performance of BLC function, We recommend that you set IRIS to AUTO in the
SSDR ON
Setup switch so that the arrow indicates EXPOSURE setup.
WHITE BAL ATW
‘BACKLIGHT’.
䯝 BACKLIGHT OFF Activating BLC may cause the camera to repeat the Auto Focus operation depending on lighting
MOTION DET OFF conditions. It is recommended that you use the Focus Setup menu in One-Push or Manual
FOCUS mode.
EXPOSURE
Smart Zoom and BLC cannot be used in conjunction with each other:
SPECIAL
RESET Setting up Smart Zoom and then BLC automatically cancels Smart Zoom.
EXIT
● SETUP
1. When the SETUP menu screen is displayed, MAIN SETUP
select ‘MOTION DETECTION’ by using the SSDR ON
Function Setup switch so that the arrow WHITE BAL ATW
indicates ‘MOTION DETECTION’. BACKLIGHT OFF
䯝 MOTION DET OFF
M For effective viewing of license plates, there is a minimum required illumination and the shutter
speed needs to be faster than 1/200sec.
FOCUS
EXPOSURE
SPECIAL
Because there can be a difference in the effectiveness of HLC according to the amount of light RESET
area in the screen, optimize the installation angle for the best HLC performance. EXIT
When dark, the HLC is only activated when a bright light exceeding a specific size. (In NIGHT
ONLY mode.)
y OFF : MOTION DETECTION mode is cancelled.
The HLC is not activated in day light or when bright light is not present at night. (In NIGHT ONLY mode.)
y ON : Any motion in the selected areas is observed.
The HLC is not activated when the D-ZOOM mode is ‘ON’ or DIS mode is ‘ON’. - AREA SEL : You can select the area
MD SETUP
you wish to observe from
the 8 area. 䯝AREA SEL AREA 1
- AREA MODE : Determines whether AREA MODE ON
to use the MD area SENSITIVITY LOW
selected in SENSITIVITY SMART ZOOM OFF
RETURN
- SENSITIVITY : You can select low
or high level. When
SENSITIVITY is high,
motion detection
sensitivity is increased to recognize even small movement
- SMART ZOOM : Smart zoom is operated in connection with MOTION
DETECTION. When the SMART ZOOM function is ‘ON’ while
the MOTION DETECTION mode is ‘ON’, the zoom goes to
the TARGET ZOOM position once motion is detected. Once
the zoom action is finished and ‘DWELL TIME’ has passed,
the zoom returns to the ‘SMART ZOOM’ position.
● SETUP
RETURN
switch in the ‘TARGET ZOOM’ item to on screen. Enabling D-ZOOM
select the zoom position from 1x to 37x to (ON) means that digital zoom will
activate once optical zoom ends. m : TELE n : WIDE
be used during MOTION DETECTION.
The focus automatically adjusts
y DWELL TIME : Use the Function Setup when the lens zooms in and out.
switch in the ‘DWELL TIME’ item to select a time between 5 and 60 seconds
for the dwell time before the zoom is returned to the ‘SMART ZOOM’ position.
(5,7,10,15,20,30,40,60 sec) - ONE PUSH : Focus is automatically adjusted
just once, after zoom position ZOOM/FOCUS POS SETUP
M
Tips on Using the Motion Detection Feature
The feature may not function properly under flickering light conditions.
is changed. Select ‘ONE
PUSH’ and the Function Setup
The camera interprets sudden changes in lighting and subsequent change in brightness of an switch to confirm. Increase or
object as motion. decrease optical zoom (ZOOM)
or digital zoom (D-ZOOM)
With the feature enabled, other algorithms may require additional time to operate.
positions using the directional m : TELE n : WIDE
This system does not guarantee prevention of fire or theft. The manufacturer shall not be held responsible key of Function Setup Switch ← : NEAR → : FAR
for any accident or damage incurred.
while verifying the changes
on screen. Press the Function
FOCUS Setup switch once the desired
image quality is obtained.
1. Press the Function Setup switch to access the main setup menu and then position
the indicator over FOCUS using the Function Setup switch.
2. Press the Function Setup switch. - MANUAL : Select ‘MANUAL’ and press
the Function Setup switch to ZOOM/FOCUS POS SETUP
y MODE : You can select the most suitable zoom mode. Move the arrow indicator confirm. Increase or decrease
to ’MODE‘ using Function Setup switch. optical zoom (ZOOM) or digital
MAIN SETUP FOCUS SETUP zoom (D-ZOOM) positions
SSDR ON 䯝 MODE AUTO moving directional key of
WHITE BAL ATW ZOOM TRACK AUTO TRACK Function Setup Switch while
BACKLIGHT OFF ZOOM SPEED FAST verifying the changes on screen. m : TELE n : WIDE
MOTION DET OFF D-ZOOM OFF Press the Function Setup switch ← : NEAR → : FAR
䯝 FOCUS ZOOM POS INIT OFF once desired image quality
EXPOSURE USER PRESET OFF is obtained. Focus can be
SPECIAL LENS INIT MANUAL
manually adjusted, independent
RESET RETURN
of moving zoom.
EXIT
● SETUP
‘ZOOM’ item to select ‘AUTOTRACK’ or USER PRESET OFF set before the power went off. USER PRESET OFF
‘TRACK’ and press Function Setup switch LENS INIT MANUAL LENS INIT MANUAL
- MANUAL : The zoom magnification level
to activate the zoom action focus function. RETURN RETURN
can be set from 1x to 37X.
- AUTO TRACK : Zooming in while
deciding or adjusting the status of the focus.
- TRACK : The camera moves the focus track which is established. M The zoom postion is saved after 5 seconds when you set zoom function.
- OFF : Only the zoom lens moves. y USER PRESET : Preset user-designated
FOCUS SETUP
configurations using this feature. Position
y ZOOM SPEED : Configure zoom tracing MODE AUTO
FOCUS SETUP the indicator over ‘USER PRESET’ using ZOOM TRACK AUTO TRACK
speed using this feature. Position the the Function Setup switch and then set
MODE AUTO ZOOM SPEED FAST
indicator over ‘ZOOM SPEED’ using the ZOOM TRACK AUTO TRACK to ‘ON’ using the Function Setup switch. D-ZOOM OFF
Function Setup switch and then set to 䯝 ZOOM SPEED FAST Press the Function Setup switch to confirm. ZOOM POS INIT OFF
desired mode using the Function Setup D-ZOOM OFF 䯝 USER PRESET OFF
- PRESET NO : Up to 128 preset
switch. ZOOM POS INIT OFF LENS INIT MANUAL
configuratons are supported.
- FAST : To move zoom fast. USER PRESET OFF RETURN
LENS INIT MANUAL
- PRESET SAVE : Save configured preset.
- SLOW : To move zoom slowly. - PRESET CLEAR : Clear configured preset.
RETURN
- MEDIUM : To move zoom at medium speed. - RETURN : Revert to the FOCUS SETUP menu.
● SETUP
BACKLIGHT OFF SSNR3 MEDIUM
2. Press the Function Setup switch to confirm. MOTION DET OFF - MANUAL : Manual shutter speed setting.
SENS-UP OFF
FOCUS - A.FLK (NTSC: 1/100, PAL: 1/120) : RETURN
䯝 EXPOSURE Flicker-free mode.
SPECIAL - ESC : Automatic shutter speed setting
RESET (optimal).
EXIT
Auto operation is possible only when
SHUTTER MANUAL SETUP
the IRIS is set to MANUAL.
y BR IGHTNESS : Use this feature to adjust 䯝SHUTTER VAL 1/50
EXPOSURE SETUP ➋ Position the indicator over ‘SHUTTER’
image brightness. Position the indicator RETURN
䯝 BRIGHTNESS IIIIIIIIIIÂIIIIIIIIIII 50 using the Function Setup switch. Then
over ‘BRIGHTNESS’ using the Function
IRIS AUTO select the desired shutter mode (A.FLK,
Setup switch. Then increase or decrease
SHUTTER --- ESC, MANUAL) using the Function
brightness level using the Function Setup
AGC HIGH Setup switch.
switch while verifying the changes on
screen. Set END once desired level is SSNR3 MEDIUM ➌ Press the Function Setup switch to complete.
obtained. SENS-UP OFF
RETURN
M Image may become unstable if the camera is set to ‘ESC’ mode and faces a strong fluorescent light.
Under ‘ESC’ mode, the brightness can be adjusted using the Function Setup switch.
y IRIS : Set ‘IRIS’ to ‘AUTO’ or ‘MANUAL’. EXPOSURE SETUP y AGC (Auto Gain Control) : For brighter images.
EXPOSURE SETUP
Position the indicator over ‘IRIS’ using the BRIGHTNESS IIIIIIIIIIÂIIIIIIIIIII 50 ➊ Position the indicator over ‘AGC’ using BRIGHTNESS IIIIIIIIIIÂIIIIIIIIIII 50
Function Setup switch and then select the 䯝 IRIS AUTO the Function Setup switch. IRIS AUTO
desired iris mode using the Function Setup SHUTTER --- ➋ Set ‘AGC’ to the desired mode using SHUTTER ---
switch. AGC HIGH the Function Setup switch. 䯝 AGC HIGH
- AUTO : The iris is automatically activated SSNR3 MEDIUM - HIGH : Wide range gain value SSNR3 MEDIUM
upon illumination. SENS-UP OFF adjustment SENS-UP OFF
- MANUAL : Manual iris configuration. Set RETURN - MANUAL : Selecting gain value range. RETURN
‘IRIS’ to ‘MANUAL’ using the (5dB ~ 41dB)
Function Setup switch and - OFF : Disabled
then press the Function Setup - LOW : Narrow range gain value
switch. Increase or decrease IRIS MANUAL SETUP GAIN MANUAL SETUP
adjustment
iris level using the Function 䯝IRIS F-No F1.6 - MEDIUM : MEDIUM range gain value 䯝AGC VAL F1.6
Setup switch while verifying RETURN adjustment RETURN
the changes on screen.
● SETUP
- OFF : Disabled WHITE BAL ATW
switch.
BACKLIGHT OFF
2. Press the Function Setup switch to confirm. MOTION DET OFF
M Changing the ‘AGC’ setting from LOW to HIGH results in greater sensitivity, as well as on screen noise. FOCUS
䯝 EXPOSURE
Setting ‘AGC’ to OFF locks ‘SSNR3’ configuration. SPECIAL
RESET
EXIT
y SENS-UP : This feature ensures clear images
at night or under low light conditions. SENS-UP LIMIT SETUP
y PRIVACY : Hide an area you want to hide
➊ Position the indicator over ‘SENS-UP’ using 䯝LIMIT X2 on the screen. SPECIAL SETUP
the Function Setup switch. RETURN 䯝 PRIVACY OFF
➊ When the SPECIAL menu screen is DAY/NIGHT AUTO
➋ Set ‘SENS-UP’ to the desired mode using displayed, using the Function Setup DIS OFF
the Function Setup switch. switch so that the arrow indicates SYNC INT
- AUTO : Select this mode for use in night ‘PRIVACY’. COMM ADJ
time or under low light conditions. IMAGE ADJ
➋ Set up the mode using the 4 direction
MONITOR LCD
- OFF : Disabled buttons..
DISPLAY
RETURN
M Once ‘AUTO’ mode is set, the user can configure the SENS-UP limit by increasing/decreasing
the shutter speed (e.g.: X2, X4....... X32, X64, X128, X256, X512).
The bigger ratio setting brightens darker area, but it may blur image of moving object and the - AREA SEL : You can select up to 12 areas. PRIVACY SETUP
Auto Focus may not appear to be optimal. - AREA MODE : Determines whether to use 䯝AREA SEL AREA1
the area selected in the AREA MODE ON
AREA SEL. MASK COLOR GRAY
TOP IIIIIIIÂIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII 39
- MASK COLOR : Determine area color. You
can select Green, Red, BOTTOM IIIIIIIIIIIIIÂIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII 79
LEFT ÂIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII 14
Blue, Black, White, Gray.
RIGHT IIIIIIIÂIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII 53
RETURN
● SETUP
indicates ‘DAY/NIGHT’.
IMAGE ADJ IMAGE ADJ
➋ Select a desired mode using the Function MONITOR LCD MONITOR LCD
Setup switch according to the picture DISPLAY DISPLAY
display you want. RETURN RETURN
y AUTO : The mode is switched to ‘Color’ in
y SYNC : Two synchronization modes are available INTERNAL and EXTERNAL
a normal environment, but switches to
AUTO SETUP LINE-LOCK.
‘B/W’ mode when ambient illumination
is low. To set up the switching time In LINE-LOCK mode, it synchronizes the camera’s video out signal to the
䯝DWELL TIME 5 SEC
or speed for AUTO mode, press the external SYNC signal.
DURATION SLOW - INT : Internal synchronization
Function Setup switch.
RETURN - LL : External line-lock synchronization
y COLOR : The picture is always
displayed in color. ➊ If you choose ‘LL’, you can adjust the desired phase.
y B/W : The picture is always displayed in Press the Function Setup switch.
black and white. ➋ You can adjust the desired phase from 0 to 359.
- DWELL TIME : You can select tday/
night switching delay time from. y COMM ADJ (Communication Adjustment) :
p 5,7,10,15,20,30,40, 60(sec) This function sets up the camera COMMUNICATION SETUP
communication status when controlling the 䯝 PROTOCOL SAMSUNG-T
- DURATION : You can select the day/night switching point(lux).
camera through an external controlled device. CAM ID ÂIIIIIIIIIIIIIIIIIIIIIIIIIIIII 1
Color p B/W B/W p Color BAUD RATE 9600
➊ When the SPECIAL menu screen is
Fast 2.6Lux 4.2Lux UART MODE 8-N-1
displayed, using the Function Setup
RET PKT DISABLE
switch so that the arrow indicates
Slow 1.2Lux 6.0Lux RETURN
‘COMM ADJ’.
 When AGC is middle mode.
➋ Set up the mode moving the 4 direction
y EXT : This mode allows you to apply a desired filter to external signals. of the Function Setup switch.
- PROTOCOL : Select the communication PROTOCOL. (SAMSUNG-T/PELCO-D/
M You cannot control the DAY/NIGHT menu when AGC in the EXPOSURE menu is ‘OFF’.
At this time, the exchange between DAY mode and NIGHT mode operates as like selecting
PELCO-P/ BOSCH/HONEYWELL/VICON/AD/SAMSUNG-E/PANASONIC)
- CAM ID : Determines the camera's identification number (between 0 and 255).
‘COLOR’ mode.
- BAUD RATE : You can select 2400/4800/9600/19200/38400/57600 bps.
The OSD key does not work for 3 seconds when switching to Color or B/W, to ensure stable
- UART MODE : You can select NONE, EVEN or ODD for the parity bits.
camera operation.
The camera may focus less well under infrared illumination than under normal illumination.
The brightness of illumination is changeable by installed environment.
32_ setup English_33
setup
- H-REV : You can flip the picture
horizontally on the screen. IMAGE SETUP
䯝H-REV OFF
- V-REV : You can flip the picture V-REV OFF
ڋ
ڒڎڍڈڪڞڮ CONTROLLER vertically on the screen. SHARPNESS ON
- SHARPNESS : As you increase this RETURN
● SETUP
value, the picture outline
becomes stronger and clearer.
ڋ
ڒڎڍڈڪڞڮ
ڋ
ڒڎڍڈڪڞڮ
ڋ
ڒڎڍڈڪڞڮ
CONTROLLER
CONTROLLER y Monitor : Please change the settings value of video appropriate to your monitor.
SPECIAL SETUP
# PRIVACY OFF
DAY/NIGHT AUTO
ڋ
ڒڎڍڈڪڞڮ
ڋ
ڒڎڍڈڪڞڮ
ڋ
ڒڎڍڈڪڞڮ
ڋ
ڒڎڍڈڪڞڮ
ڋ
ڒڎڍڈڪڞڮ
ڋ
ڒڎڍڈڪڞڮ
DIS OFF
SYNC INT
COMM ADJ
IMAGE ADJ
CONTROLLER 䯝 MONITOR LCD
DISPLAY
RETURN
- RET PKT : You can choose whether to send an ACK signal when the - LCD : Please select this menu item LCD MONITOR SETUP
communication control command is issued to the camera. when using an LCD monitor. 䯝GAMMA 0.45
PED LEVEL IIIIIIIIÂIIIIIIIIIIIIIIIIIIIII 17
y IMAGE ADJ : Includes image quality or
special function factors. SPECIAL SETUP COLOR LEVEL IIIIIIIIIIIIIIIIIÂIIIIIIIIIIII 50
# PRIVACY OFF RETURN
➊ When the SETUP menu screen is displayed, select DAY/NIGHT AUTO
‘IMAGE ADJ.’ using the Function Setup switch so DIS OFF
that the arrow indicates 'IMAGE ADJ. SYNC INT - CRT : Please select this menu item
COMM ADJ when using a CRT monitor. CRT MONITOR SETUP
➋ Select a desired mode using the Function Setup 䯝 IMAGE ADJ 䯝PED LEVEL IIIIIIIIÂIIIIIIIIIIIIIIIIIIIII 17
switch. MONITOR LCD COLOR LEVEL IIIIIIIIIIIIIIIIIÂIIIIIIIIIIII 50
DISPLAY RETURN
RETURN
● SETUP
➎ Enter a title, move the cursor to ‘POS’ and press
the Function Setup Switch. The entered title FRONT DOOR
appears on the screen. Select the position to
y DISPLAY : Use this feature to designate a display the title on the screen by moving the 4
name for the camera, which will display on SPECIAL SETUP
# PRIVACY OFF direction of Function Setup Switch and press
the monitor screen.
DAY/NIGHT AUTO the Function Setup Switch. When the position is
- CAM TITLE : If the camera is named, it is DIS OFF determined, select.
displayed on the monitor. SYNC INT - CAM ID : Displays camera ID on top left corner of the screen.
➊ Press the Function Setup switch to display the main COMM ADJ
IMAGE ADJ - CAM INFO : Displays camera information on screen.
setup menu and move the arrow indicator to ‘CAM
MONITOR LCD - MOTION ALARM : You can toggle the use of the camera alarm.
TITLE’ using the Function Setup switch.
䯝 DISPLAY
- ZOOM MAG : Use th is feature to display the current zoom magnification level on
➋ Set ‘CAM TITLE’ to ‘ON’ using the Function Setup RETURN
screen. Position the indicator over ‘ZOOM MAG’ using the Function
switch.
Setup switch. Then set to ON using the Function Setup switch.
DISPLAY SETUP - FONT COLOR : You can select the font color(white,yellow,green,red,blue)
䯝CAM TITLE OFF
M If the CAM TITLE feature is set to ‘OFF’, the name
will not displayed in the monitor
CAM ID ON
- LANGUAGE : You can select the menu language according to your requirements.
• NTSC : Korean, English, French, Spanish, Japanese, Portuguese,
CAM INFO ON
MOTION ALARM OFF Taiwanese
ZOOM MAG ON • PAL : English, French, German, Spanish, Italian, Chinese, Russian, Czech,
➌ Press the Function Setup switch. FONT COLOR WHITE Polish, Portuguese, Romanian, Serbian, Swedish, Danish, Turkish
LANGUAGE ENGLISH - END : Select this to save the SPECIAL menu settings and return to the
➍ You can enter up to 15 characters. RETURN SPECIAL menu.
a. Move the cursor to the character entry field
using the Function Setup switch.
b. Use the 4 direction of Function Setup Switch CAMERA TITLE SETUP RESET
to select a desired character. A B C D EF G H I J K L M
To reset your camera to factory default condition.
c. Press the Function Setup switch to confirm N O P Q R S T U V WXY Z
the selection of the blinking character. The abcdefghi j klm
character is then saved, and the cursor in the n o p q r s t u v wxy z EXIT
entry field moves to the next position. - . 0123456789
To finish setup menu.
d. Repeat steps 'a' through 'c' until the desired ← → CLR POS END
name has been entered.
● SPECIFICATIONS
Nothing appears on the screen. f Check that the power cord and line connection between the Max. 3.8W, 4.8W ( DC12V / AC 24V, Fan & Heater Off )
Power Consumption
Max. 28W ( Heater & Fan On, AC 24V )
camera and monitor are fixed properly.
f Check that you have properly connected VIDEO cable to the Video
camera VIDEO output jack. Imaging Device 1/4” Super HAD CCD
Total Pixels 811(H) x 508(V) 795(H) x 596(V)
The image on the screen is dim. f Is lens stained with dirt? Clean your lens with soft, clean cloth.
f Set the monitor to proper condition. Effective Pixels 768(H) x 494(V) 752(H) x 582(V)
f If the camera is exposed to too strong light, change the camera Scanning System 2 : 1 Interlace 2 : 1 Interlace
position. Synchronization Internal / Line lock
The image on the screen is dark. f Adjust the contrast feature of the monitor. Frequency H : 15.734KHz / V : 59.94Hz H : 15.625KHz / V : 50Hz
f If you have an intermediate device, set the 75Ω / Hi-z properly. Horizontal Resolution Color : 600 TV Lines, B/W : 700 TV Lines
Color : 0.2 Lux (50IRE@F1.2), 0.0004 Lux (Sens-up, 512x)
The camera is not working f Check that you have properly connected the camera to an Min. Illumination
B/W : 0.02 Lux (50IRE@F1.2)
properly, and the surface of the appropriate power source.
S / N (Y signal) 52dB (AGC off, Weight on)
camera is hot.
Video Output CVBS : 1.0 Vp-p / 75Ω composite
The SENS-UP function does not f Check that AGC of EXPOSURE SETUP menu is ‘OFF’. Lens
work. f Check that SHUTTER of EXPOSURE SETUP menu is ‘A.FLK’ or
Zoom Ratio 37x (Optical), 16x (Digital)
‘MANUAL’.
Focal Length 3.5 ~ 129.5mm (F1.6 ~ 3.9)
The Motion Detection function does f Check that MOTION DET of SPECIAL SETUP menu is ‘OFF’. Max. Aperture Ratio 1 : 1.6(Wide) ~ 3.9(Tele)
not work.
Angular Field of View H : 55.5°(Wide) ~ 1.59°(Tele) / V : 42.5°(Wide) ~ 1.19°(Tele)
Color is not correct. f Check the setting of WHITE BAL SETUP menu . Min. Object Distance 150cm (Tele)
Focus Auto / Manual / One push
The screen flickers continually. f Check that direction of camera turns toward the Sun.
Zoom Movement Speed 2.8 sec ( Wide to Tele )
When coaxial communication is f Make sure that the camera and monitor are installed within the Operational
not available: recommended distance.
English, Spanish, French, Italian,
f Use the video amplifier equivalent to coaxitron if the English, Japanese, Spanish, French, German, Polish, Russian, Czech,
recommended installation distance is exceeded. On Screen Display
Portuguese, Taiwanese, Korean Chinese, Danish, Portuguese, Romanian,
Serbian, Swedish, Danish, Turkish
Camera Title Off / On ( Displayed 15 characters )
Backlight Compensation BLC/HLC/Off
SSDR On / Off
Digital Noise Reduction (2D+3D) On / Off
Digital Image Stabilization On / Off
● SPECIFICATIONS
Sens-up (Frame Integration) Auto / Off (Selectable x2 ~ x512)
Gain Control Low / Medium / High / Manual / Off
White Balance AWC/Manual/Outdoor/Indoor/ATW (1700°K~11,000°K)
Electronic Shutter Speed 1/60 ~ 1/1200,000
Digital Zoom On / Off (2x ~ 16x)
Flip / Mirror On / Off
Communication RS-485 & Coaxial Control (Pelco Coaxitron)
Protocol Samsung-T, Samsung-E, Pelco-D, Pelco-P, AD, Bosch, Honeywell, Vicon, Panasonic
ENVIRONMENTAL
-50°C to +50°C / Less than 90% RH (AC 24V)
Operating Temperature / Humidity
-30°C to +50°C / Less than 90% RH (DC 12V)
Weather Proof IP68
MECHANICAL
Dimension Ø114 x 378mm
Weight 1.95Kg(4.29lb)
 The specification for this product may change without prior notice for product improvement.
Byte1 Byte2 Byte3 B yte4 ll Byte5 Byte 6 Byte7 Byte8 Byte9 Byte10 Byte11
Command Packet STX CAM ID HOST ADDR CAMMAND DATA3 DATA4 DATA5 DATA6 ETX CHECKSUM
We, the undersigned, hereby declare that the equipment specified above conforms
to the above Directive(s).
www.samsungtechwin.com
www.samsungsecurity.com
P/NO. : Z6806134201A/01