Documente Academic
Documente Profesional
Documente Cultură
BT - Broken teeth and cutters OC - Off centre wear 8 - Reasons bit was pulled or run completed
BU - Balled up bit PB - Pinched bit BHA- Change bottom hole assembly HR - Hours on bit
CC - Cracked cone * PN- Plugged nozzle or flow by areas DMF - Downhole motor failure LOG - Run logs
CD - Cone dragged * RG - Rounded gauge DTF - Downhole tool failure PP - Pump pressure
CI - Cone interference RO - Ring out DSF - Drill string failure PR - Penetration rate
CR - Cored SD - Shirttail damage DST - Drill stem test Rig - Rig repair
CT - Chipped Teeth & cutters SS - Shelf sharpening wear DP - Drill Plug TD - Total depth / casing depth
ER - Erosion TR - Cone tracking CM - Condition mud TW - Twist off
FC - Flat crested wear WO - Wash out CP - Core point TQ - Torque
HC - Heat checking WT - Worn teeth or cutters FM - Formation change WC - Weather conditions
LD - Junk damage NO - No dull characteristics HP - Hole problems
LC - Lost cone * * Show cone # or #'s under location 4 LIH - Left in hole
TCI/Insert bits.
4 Soft formations 1. Very soft shale
Low compressive strengths 2. Soft shales.
3. Medium soft shale / lime
4. Medium lime shale.
5 Soft - medium hard formations 1. Very soft shale / sand.
Low compressive strengths 2. Soft shale / sand.
3. Medium soft shale / lime.
6 Medium - hard formations 1. Medium lime / shale.
High compressive strengths 2. Medium hard lime / sand.
3. Medium hard lime/sand/slate
7 Hard semi - abrasive 1. Hard lime / dolomite.
and abrasive formations 2. Hard sand /dolomite.
3. Hard dolomite.
8 Extremely hard & abrasive 1. Hard chert.
& abrasive 2. Very hard chert.
3. Hard granite.
Number of nozzles
Nozzle size 1 2 3 4 5 6 7 8 9
82 secs 36 ft/hr
80 secs 35 ft/hr
Rate of penetration
Rate of penetration
33 ft/hr
33 ft/hr
75 secs
73 secs
31 ft/hr
70 secs 30 ft/hr 30 ft/hr
68 secs 29 ft/hr
62 secs
60 secs 60 secs 25 ft/hr
30 Klbs 40 Klbs 50 Klbs 100 RPM 120 RPM 140 RPM
2 26.00 REED Y12 JE2828 20 20 20 20 1.2 0.8 286 638 0 2 0.5 0 5/15 60/90 4/6 1100 800 SW 8.6 ~ ~ ~ 1 1 NO A E I NO TD Drill cement.
EHP
5 12.25 Reed
51HDL
5940299 18 18 18 0 0.7 6.4 374 6148 387 16 14.3 27 35/50 120 2/6 871 3650 WBM 11.8 46 27 26 2 7 LT G12###1/16" BT PR Limestone/Chert, (90% in some samples )
7 8.50 Bbits BB657 405424RR 6 x 12 0.7 3.7 242 7085 15 3 1.0 15 7580 170 2/6 500 3900 OBM 13.5 70 40 20 Add 4.5hrs drilling cmt plugs etc.