Documente Academic
Documente Profesional
Documente Cultură
TESTING MANUAL
TASK 71-21-00-213-804-B
EFFECTIVITY: ALL
ENGINE AFT MOUNT - INTERNAL
1. General
A. This task gives the procedure to do a detailed inspection of the engine aft mount-assembly, including
yoke, links, clevises, lugs and attachment hardware, LH/RH internal side of nacelle.
HARD COPY IS UNCONTROLLED. ONCE PRINTED, THIS PAGE MUST NOT BE RETAINED FOR FUTURE REFERENCE.
D. Structural Significant Item(s): 71-21-002 - ENGINE AFT MOUNT ASSEMBLY.
2. References
REFERENCE DESIGNATION
BEFORE USING, MAKE SURE THIS HARD COPY IS THE LATEST ISSUE.
Aircraft Maintenance Safety Procedures - Standard Proce-
AMM TASK 20-00-00-910-801-A/200
dures
Connection of the external AC power supply to the aircraft -
AMM TASK 24-42-02-860-801-A/200
Aircraft/System Configuration
Disconnection of the external AC power supply from the air-
AMM TASK 24-42-02-860-802-A/200
craft - Aircraft/System Configuration
AMM TASK 52-46-00-000-801-A/400 Middle Avionics-Compartment Access-Door - Removal
AMM TASK 52-46-00-400-801-A/400 Middle Avionics-Compartment Access-Door - Installation
AMM TASK 71-11-00-910-801-A/200 Fan Cowl - Open
AMM TASK 71-11-00-910-802-A/200 Fan Cowl - Close
AMM TASK 71-21-01-000-801-A/400 Engine Aft Mount - Removal
AMM TASK 71-21-01-400-801-A/400 Engine Aft Mount - Installation
AMM TASK 78-30-01-910-801-A/200 Thrust Reverser - Open
AMM TASK 78-30-01-910-802-A/200 Thrust Reverser - Close
AMM TASK 78-33-01-040-801-A/200 Isolation Control Unit (ICU) - Deactivation
AMM TASK 78-33-01-440-801-A/200 Isolation Control Unit (ICU) - Reactivation
Filtered Serial Nº contained in this publication: 178
ZONES
LOCATION REFERENCE
ACCESS
(Continued)
ZONES
LOCATION REFERENCE
ACCESS
HARD COPY IS UNCONTROLLED. ONCE PRINTED, THIS PAGE MUST NOT BE RETAINED FOR FUTURE REFERENCE.
4. Tools and Equipment
REFERENCE DESIGNATION
BEFORE USING, MAKE SURE THIS HARD COPY IS THE LATEST ISSUE.
Commercially available Hand - Held 10X Minimum Magnifying Lens
Commercially available Wiper cloth, lint-free
Commercially available Workstand - Engine/Pylon
Commercially available Circuit Breaker Ring and Tag (Inoperative - Do Not Operate)
MCDU
TYPE DESIGNATION LOCATION BUS LOCATION TIP
PAGE
6. Job Set-Up
WARNING: MAKE SURE THAT THE AIRCRAFT IS IN A SAFE CONDITION BEFORE YOU DO THE
MAINTENANCE PROCEDURES. THIS IS TO PREVENT INJURY TO PERSONS AND/OR
DAMAGE TO THE EQUIPMENT.
A. Do the procedure to make the aircraft safe for maintenance (AMM TASK 20-00-00-910-801-A/200).
B. Connect the external AC power supply to the aircraft (AMM TASK 24-42-02-860-801-A/200).
C. Open these circuit breakers and put a circuit breaker ring and tag (inoperative - do not operate) on
each one of them:
D. On the MCDU (AMM SDS 34-61-00/1), use the sequence in parentheses to open these SSPCs:
HARD COPY IS UNCONTROLLED. ONCE PRINTED, THIS PAGE MUST NOT BE RETAINED FOR FUTURE REFERENCE.
(2) Open and remove the access door 147AL (AMM TASK 52-46-00-000-801-A/400).
F. Open these circuit breakers and put a circuit breaker ring and tag (inoperative - do not operate) on
each one of them:
BEFORE USING, MAKE SURE THIS HARD COPY IS THE LATEST ISSUE.
• E1 REVERSER-LICC (DC BUS 1)
H. Use a workstand (engine and pylon) to get access to the area that you will examine.
I. Open access doors 413AL, 412AR, 423AL, and 422AR (AMM TASK 71-11-00-910-801-A/200).
J. Open access doors 415AL, 414AR, 425AL, and 424AR (AMM TASK 78-30-01-910-801-A/200).
L. Before you do the inspection, clean the area that you will inspect with a lint-free wiper cloth soaked in
water.
7. Procedure (Figure 1)
B. Use a 10X magnifying lens to do the detailed inspection of the engine aft mount-assembly, including
yoke, links, clevises, lug and attachment hardware, LH/RH internal side of nacelle. Make sure that:
• There are no nicks, scratches, gouges, dents, corrosion and other signs of damage.
8. Indication Evaluation
(1) Install and close the access door 147AL (AMM TASK 52-46-00-400-801-A/400).
HARD COPY IS UNCONTROLLED. ONCE PRINTED, THIS PAGE MUST NOT BE RETAINED FOR FUTURE REFERENCE.
C. Close access doors 413AL, 412AR, 423AL, and 422AR (AMM TASK 71-11-00-910-802-A/200).
D. Close access doors 415AL, 414AR, 425AL, and 424AR (AMM TASK 78-30-01-910-802-A/200).
BEFORE USING, MAKE SURE THIS HARD COPY IS THE LATEST ISSUE.
E. Remove the workstand (engine and pylon) and all tools, equipment and unwanted materials from the
worked area.
G. Remove the circuit breaker ring and tag (inoperative - do not operate) from each of these circuit
breakers and close them:
(1) Install and close the access door 147AL (AMM TASK 52-46-00-400-801-A/400).
I. On the MCDU (AMM SDS 34-61-00/1), use the sequence in parentheses to close these SSPCs:
J. Remove the circuit breaker ring and tag (inoperative - do not operate) from each one of these circuit
breakers and close them:
K. Disconnect the external AC power supply from the aircraft (AMM TASK 24-42-02-860-802-A/200).
EFFECTIVITY: ALL
Engine Aft Mount-Assembly - Inspection
Figure 1
HARD COPY IS UNCONTROLLED. ONCE PRINTED, THIS PAGE MUST NOT BE RETAINED FOR FUTURE REFERENCE.
B
A
BEFORE USING, MAKE SURE THIS HARD COPY IS THE LATEST ISSUE.
ZONES
416
426
FIXED LINK
FIXED LINK
LEGEND:
INSPECTION AREA.